Hanwha Techwin SSA-S1000V Standalone RFID Access Controller User Manual 20101005 v1 Appen

Download:
Mirror Download [FCC.gov]
Document ID	1355655
Application ID	+Ghxx36/ShZkOn0kmCiLww==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	23.06kB (288231 bits)
Date Submitted	2010-10-07 00:00:00
Date Available	2010-10-07 00:00:00
Creation Date	2010-10-07 18:11:49
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2010-10-07 18:11:49
Document Title	User Manual_20101005_v1 - Appen.PDF
Document Creator	PScript5.dll Version 5.2
Document Author:	ltsai

Standalone RFID
Access Controller
User Manual
SSA-S1000V
Standalone RFID Access Controller
User Manual
Copyright
©2010 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung
Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but
no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the
user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without
prior notice.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve
the problem for free of charge. The warranty period is 3 years. However, the followings are excluded:
• If the system behaves abnormally because you run a program irrelevant to the system operation.
• Deteriorated performance or natural worn-out in process of time
• Sensory phenomenon that does not affect the performance or quality of the product (ex : working noise)
safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
This symbol indicates that dangerous voltage consisting a risk of electric shock is
present within this unit.
This exclamation point symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING
• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to
the product.
3. Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the controller, fasten it securely and firmly. The fall of controller may cause personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the
controller. Doing so may cause personal injury due to fire, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the
power source and contact the service center. Continued use in such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in
any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)
10.. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive
vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -20°C), or high humidity.
Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fire or damage
to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the controller directly towards extremely bright objects such as sun.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.
English English _ 3
SAFETY INFORMATION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
safety information
FCC Statement
Caution : Any changes or modifications in construction of this device which are not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, any cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third
prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus
combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
4_ safety information
contents
Feature
What’s included
At a Glance
Cable Color Scheme
Cable Selection
INSTALLATION AND EXTERNAL
CONNECTION
10
10
11
Installation
Bypass Diode Connection
I/O Connection
SYSTEM INITIALIZATION & BASIC
OPERATIONS
13
13
14
14
Initializing the system by short-circuiting
Basic Operations
To register /delete Master ID
To register/delete ID card
TROUBLESHOOTING
15
TroubleShooting
PRODUCT SPECIFICATIONS
16
Product Specifications
10
13
15
16
English English _ 5
CONTENTS
PRODUCT INTRODUCTION
product introduction
FEATURE
This product is designed for use with one-door access control for security applications. With its compact design, you can
install this product on the wall or a doorframe; Its epoxy adhesion and aluminium case guarantee shock-resistance as well as
stable operation in a challenging environment. This product enables you to control the door using the user card and provides
a simple method to register or delete cards, and initialize the system, which is, one of the most convenient and safest door
controller.
And it is also featured by the 2-color LED indicator and the internal buzzer, enabling you to easily check the current mode
and operation of the door lock.
◆ 125 kHz Proximity Access Controller
◆ Up to 512 users including one Master ID can be registered
◆ Standalone (no application S/W required)
◆ Direct Control of the Door Lock
◆ Can select a lock device type from Power Fail Safe and Power Fail Secure
◆ Epoxy adhesion and aluminium case
◆ Weatherproof and Dustproof
6_ product introduction
WHAT’S INCLUDED
Check if the following items are included in the product package.
SSA-S1000V
Bezel
Main Module
Master Card (x1)
Keytag (x5)
3mm Hex Wrench (x1)
3.5 x 40mm Screws (x2)
3.5 x 25mm Screws (x2)
6 x 30mm Plastic Anchors (x2)
Diode (X 2)
(UF4004, 1N4001~4007)
Quick Guide
CD Manual
English English _ 7
PRODUCT INTRODUCTION
tˆš›Œ™Gjˆ™‹
product introduction
AT A GLANCE
Front/Rear
SSA-S1000V
LED
Displays the system operation status using red and green indicators.
Fixing Hole
Fixing hole for wall-mounting.
Connection Cable
Used to connect to the power or I/O cable.
Tamper Switch
A tamper switch to detect falling from the wall.
Buzzer
Piezo buzzer.
8_ product introduction
CABLE COLOR SCHEME
Item
Cable Color
Signal Line
Description
Red
DC+12V
Black
GND
Yellow
AUX INPUT#1
Blue
Door Contact Sensor
Green
Exit Button
Exit Button Connection Port
Purple
Alarm Out
Alarm Device Connection
Port
White
Door Lock Out
Door Lock device connection
port
Pink
TAMPER COM
COM Port of Tamper
Switch
Light yellow
TAMPER NC
+12V supplied
Input
Earth-Grounding for Power
Select a Lock Type
Door Sensor Connection Port
Output
Tamper
NC Port of Tamper Switch
Gray
Orange
Not used
Brown
CABLE SELECTION
Item
Power (DC +12V)
Belden #9409, 18 AWG 2 Conductor, Unshielded
Door Contact Sensor
Belden #9512, 22 AWG 4 Conductor, Shielded
Exit Button
Sensor Input
Tamper
Cable Type
Door Lock
Alarm Device
Belden #9514, 22 AWG 8 Conductor, Shielded
Belden #9409, 18AWG 2 Conductor, Unshielded
English English _ 9
PRODUCT INTRODUCTION
Power
installation and external connection
INSTALLATION
6-32 hole
6-32 or M3 Screws
1/2” hole
63.1mm
6-32 hole
Reader
Module
22.1mm
000V
SSA-S1
Bezel
3mm Hex Wrench
- On a doorframe or the wall
1. Drill a 1/2-inch (12.7 mm) hole onto the center of the doorframe or the wall where SSA-S1000V is installed,
which makes room for the cable of the reader module.
2. Drill a 6-32 inch hole at the 43.1mm point straight higher from the center hole and at 22.1mm straight lower,
respectively.
3. Insert the reader module cable to the center hole and fix the module using two screws inserted in the upper and
lower corners.
4. Insert the outer case into the product and fix it with the 3mm hex wrench.
BYPASS DIODE CONNECTION
If you connected an inductor (door lock or alarm device) to the output relay, there should occur a voltage surge while the
inductor was between turning on and turning off. If you do not connect a reverse diode to the relay, the voltage surge will
cause damage to the electric circuit of the controller. To reduce this surge, it is recommended to connect the bypass
diode to the relay.
10_ installation and external connection
I/O CONNECTION
Input Connection
INSTALLATION AND EXTERNAL CONNECTION
DOOR CONTACT (blue)
Door Contact Sensor
EXIT BUTTON
(green)
Exit Button
PUSH
SSA-S1000V
DC +12V
GND
(black)
GND
DC +12V
(red)
DC 12V(+) POWER
- To connect the power supply unit
1. Connect the DC+12V to the red line.
2. Connect GND to the black line.
- To connect the Door Contact Sensor
1. Connect the COM port of the sensor to the blue line.
2. Connect the NO port of the sensor with the GND line.
- To connect the Exit Button
1. Connect one end of the button to the green line.
2. Connect the other end of the button to GND.
English English _ 11
installation and external connection
Output Connection
DOOR LOCK OUT
(white)
Door Lock
ALARM OUT
(purple)
Alarm Device
SSA-S1000V
Lock Type Select
(yellow)
Cathode
Anode
1N4004 ~ 1N4007 or equiv.
DC +12V
GND
DC 12V(+) POWER
- To connect the power supply unit
1. Connect the DC+12V to the red line.
2. Connect GND to the black line.
- To connect the door lock device
1. Connect the plus(+) line of the lock device to DC+12V.
2. Connect the minus(-) line of the lock device to the white line.
- To connect the alarm device
1. Connect the plus(+) line of the alarm device to DC+12V.
2. Connect the minus(-) line of the alarm device to the purple line.
- To specify the lock type
POWER FAIL SAFE: Connect the yellow line to GND.
POWER FAIL SECURE: Leave the yellow line in the floating state.
12_ installation and external connection
system initialization & basic operations
INITIALIZING THE SYSTEM BY SHORT-CIRCUITING
Short-Circuit
White
2. When you turn the product back on, all of the LED indicators
turn red or green, repeat turning on/off twice before being
completely turned off.
Door Lock
Green
Exit Button
Yellow
Lock Type
3. In the power-off condition, all LED indicators turn green
bottom up in sequence.
SSA-S1000V
4. When you hear a beep 4 times, that indicates that the
initialization is completed.
Black
Power
Red
 If you initialize the system, all of the data settings will return to the factory default.
BASIC OPERATIONS
When the power is supplied
1. All of the LED indicators will turn red or green, and repeat turning ON/OFF twice before being completely turned
OFF. In the power-off condition, all LED indicators turn red bottom up in sequence.
2. You will hear a beep once.
When you present a registered card to the product or press the Exit button
1. All LED indicators turn from red to green, and turn off top down in sequence before turning back red.
2. Then, the door stays open for the specified time with the upper one indicators turning green, which indicates the
door is open.
3. You will hear a beep once.
When you present an unregistered card to the product
1. All LED indicators turn red, and repeat turning on/off twice before staying in ON.
2. You will hear a beep twice.
When you present a user card to the product while the door is open
1. The one LED indicators from the top stay green, indicating the door is open; in the mean time, the other
indicators reflect the authentication results.
English English _ 13
SYSTEM INITIALIZATION & BASIC OPERATIONS
1. Turn off the product and short-circuit three lines: white line of
the door lock device, green line of the Exit button, and yellow
line of the lock type.
system initialization & basic operations
TO REGISTER /DELETE MASTER ID
1. First turn off the product, and short-circuit two lines: purple line of
Alarm Out and blue line of the Door Contact Sensor.
SSA-S1000V
Cable
Blue
2. When you turn the product back on, you will hear the beep twice while
all of the LED indicators turn red, and repeat turning on/off twice before
being completely ON; then the Master card will be deleted.
Yellow
Green
Short-Circuit
3. Upon deletion of the Master Card, you will hear a beep once and
all of the LED indicators toggle between green and red twice
before turning off; in this condition, they turn red from bottom up
in sequence.
Purple
White
SSA-S1000V
Red
DC12V
4. When the deletion is completed, turn off the product.
Connect the purple line of Alarm Out and the blue line of the Door
Contact Sensor back to their original ports, respectively.
Power
GND
Black
5. When you turn the product back on, it recognizes and registers the first-read card as the Master Card. And
if you present a registered user card to the product upon deletion of the Master Card, that card will be
registered as the Master Card.
 If you present a registered user card after the Master Card is deleted, that card will be registered as the Master Card.
TO REGISTER/DELETE ID CARD
1. If you present the Master Card to the product, it will sound the beep
once and the first two LED indicators from the top will turn green from
the top.
2. If you present a new user card to the product, it will sound the beep
once and all of the LED indicators except for the first two ones from
the top will turn from red to green. Then, they all turn off and turn
back on bottom up in sequence. When all of the LED indicators turn
back on, they will turn red except for the first two LED indicators from
the top . Then, the user card will be registered.
SSA-S1000V
MASTER CARD
SSA-S1000V
3. If you present a registered user card, the product will sound the beep twice and all LED indicators except for the
first 2 from the top will turn red, and repeat turning on/off twice before being completely ON. Then the user card
will be deleted.
4. When you present the Master Card to the product after the user card is deleted, the product will sound the
beep once and all of the LED indicators turn red, starting with the first two LED indicators from the top turning
from green to red.
 If you present a registered user card after the Master Card is deleted, that card will be registered as the Master Card.
14_ system initialization & basic operations
troubleshooting
TROUBLESHOOTING
If the product does not function properly, please see the below for trouble shooting.
SOLUTION
PROBLEM
1)
The Exit button does not work at all.
1)
Check if the product works properly.
- If the product works properly and you have the Master Card
c Read the Master Card.
d Read the card to delete.
e Read the Master Card again to switch to normal mode.
f For more information about deleting user cards, refer to the ID registration and
deletion section in this manual.
- If you lost the Master Card
c Turn off the product and short-circuit the purple and blue lines, then turn the
product back on.
d The Master ID will be deleted with a flashing LED indicator and beep.
e When the Master card is deleted, turn off the product and restore the purple
and blue lines to their respective original positions.
f The very first card read by the product after turning on the product will be
registered as the Master Card.
g For deleting the ID once the Master Card is registered, refer to the ID
registration and deletion section in this manual.
h Turn off the product and short-circuit the purple and blue lines, then turn the
product back on.
i The Master ID will be deleted with a flashing LED indicator and beep.
j When the Master card is deleted, turn off the product and restore the purple
and blue lines to their respective original.
k The very first card read by the product after turning on the product will be
registered as the Master Card.
Check if the Exit button is connected to SSA-S1000V properly. (the Exit button
should be used with a NO-type button)
2) Check if the Exit button works normally.
- Check the connection cable between the Exit button and SSA-S1000V for any
disconnection or short-circuit.
- Try to connect the two lines on the Exit button.
c If SSA-S1000V responds when you press the Exit button
¥ Replace the Exit button as it is defective.
d If SSA-S1000V does not respond at all
¥ Initialize the product as it is damaged or malfunctions. (Initializing the product
will lose all user data.)
3) If the trouble persists after following the procedures above, contact a
designated service center.
English English _ 15
TROUBLESHOOTING
The user card is not deleted.
product specifications
PRODUCT SPECIFICATIONS
Item
SSA-S1000V
Users
512 Users
Power / Current
DC 12V / Max.180mA
Reading Time (Card)
30ms
Door Open Time
5sec. (Fixed)
Input Port
3ea: Exit Button, Door Sensor, Lock Type Select [Power fail Safe / Power Fail Secure]
Output Port
2ea : TR Output / DC 12V. Rating Max. 300mA Alarm Output, DC 12V. Rating Max.
1A Lock Output
LED Indicator
5 LED Indicators (Red and Green)
Beeper
Piezo Buzzer
Operating Temperature
-20°C to +50°C
Operating Humidity
10% to 90% Relative Humidity Non-Condensing
Color / Material
Silver with Black/ Polycarbonate & Aluminum Die casting
Dimension
(W x H x D(mm))
47 x 120 x 26
Weight
250g ±10
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these
items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for
details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of
with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate
that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are
not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and
recycle them through your local, free battery return system.
16_ product specifications
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : +1-877-213-1222 FAX : +1-310-632-2195
www.samsungcctvusa.com
www.samsungsecurity.com
www.samsungtechwin.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
P/No. : Z8100239401A

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2010:10:07 18:11:49-07:00
Modify Date                     : 2010:10:07 18:11:49-07:00
Page Count                      : 17
Creation Date                   : 2010:10:08 01:11:49Z
Mod Date                        : 2010:10:08 01:11:49Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : ltsai
Metadata Date                   : 2010:10:08 01:11:49Z
Creator                         : ltsai
Title                           : User Manual_20101005_v1 - Appen.PDF

EXIF Metadata provided by EXIF.tools