Harbor Freight Assorted Aluminum Polishing Kit With 1 4 In Shank 14 Pc Product Manual
Manual for the 98707 14 Piece Aluminum Polishing Kit 98707 Aluminum Polishing Tool Kit - 14 Piece
2015-05-27
: Harbor-Freight Harbor-Freight-Assorted-Aluminum-Polishing-Kit-With-1-4-In-Shank-14-Pc-Product-Manual-723254 harbor-freight-assorted-aluminum-polishing-kit-with-1-4-in-shank-14-pc-product-manual-723254 harbor-freight pdf
Open the PDF directly: View PDF .
Page Count: 2
Manual Revised 11g
14 pc. Aluminum Polishing Kit
Item 98707
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-800-444-3353 as soon as possible.
Visit our website at: http://www.harborfreight.com
Email our technical support at: tech@harborfreight.com
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools. Diagrams
within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described
herein. Tools required for assembly and service may not be included.
Specications
Part Description MAX
RPM QTY
14" Diameter Bufng Wheel 2,800 1
22-1/2" Diameter Bufng Wheel 2,800 1
3 3" Diameter Polishing Wheel 2,800 1
42-1/4" L X 2" D to 1-1/4" D
Tapered Buffer 2,800 1
51-3/4" L X 1-3/4" D
Cylindrical Buffer 2,800 1
62-3/4" D
Mushroom Style Buffer 2,800 1
72-1/4" L X 3/4" D
Ball Type Felt Bob 20,000 1
82-3/4" L X 3/4" D
Bullet Type Felt Bob 20,000 1
92-7/16" L X 3/4" D
Pear (Balloon) Type Felt Bob 20,000 1
10 2-3/8" L X 1" D Wide Cone
(Dome) Type Felt Bob 20,000 1
11 2-1/2" L X 3/4" D
Cone Type Felt Bob 20,000 1
12 Black Emery Compound (For
Hard Bufng Wheels - Coarse) 1
13 Brown Tripoli Compound
(For Rough Bufng - Medium) 1
14 White Aluminum Oxide
Compound (Fine) 1
Safety Information
1. Do not exceed the stated
maximum RPM for each item.
2. Wear ANSI-approved safety
goggles during use.
3. Keep bystanders out of the
work area during use.
4. Inspect before use; do not use if
parts are loose or damaged.
Polishing Instructions
1. Remove deep scratches from the
workpiece and clean thoroughly
to remove any dirt, grease or oil.
2. Clamp rmly in place.
3. Connect the chosen accessory (Part 1 -
11) to an electric drill (sold separately).
Set the drill speed at or below the
maximum RPM for the accessory.
4. Turn on the drill. When the accessory
is rotating at full speed, gently rub
the bufng compound against the
rotating pad to load the accessory
with the polishing medium.
Note: Use the appropriate bufng
compound for the job. Do not mix
compounds on the same accessory.
Coarser compounds mixed with ner
compounds will scratch the surface
when polishing. Begin with the coarse
compound, then work up to the nest
compound, thoroughly cleaning the
workpiece and switching wheels before
changing to the next compound. See
Specications at left for compound types.
5. Slowly move the accessory over
the workpiece. Keep the accessory
moving to avoid an uneven nish.
6. When nished with the compound
loaded accessory, repeat the
process using a clean accessory
to clean any compound residue.
SKU 98707 For technical questions, please call 1-800-444-3353. Page 2