Harbor Freight Multipurpose Workbench With Light Product Manual

2015-05-27

: Harbor-Freight Harbor-Freight-Multipurpose-Workbench-With-Light-Product-Manual-723970 harbor-freight-multipurpose-workbench-with-light-product-manual-723970 harbor-freight pdf

Open the PDF directly: View PDF .
Page Count: 12

Download
Open PDF In Browser	View PDF

Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
REV 15e

Tools Sold Separately

Visit our website at: http://www.harborfreight.com
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2012 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.

Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Table of Contents
Safetye��������������������������������������������������������� 5
Specifications.............................................. 4
Assembly..................................................... 5

Maintenancei����������������������������������������������� 8
Parts List and Diagram............................... 10
Warranty..................................................... 12

WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMPORTANT SAFETY INFORMATION
Assembly Precautions
1. Assemble only according to these instructions.
Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.

4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or when under the
influence of alcohol, drugs or medication.
6. Weight capacity and other product capabilities apply
to properly and completely assembled product only.

Use Precautions
1. This product is not a toy. Do not allow
children to play with or near this item.
2. Setup and use indoors only. Keep dry.
3. Do not overtighten workpiece; damage
to workpiece may occur. Be careful not
to pinch fingers when working
4. Locate Workbench on a flat, level, solid surface
that is capable of supporting the weight of
the workpiece, Workbench and tools.
5. Use as intended only.
6. Replace bulb only with same bulb size and rating.
7. Inspect before every use; do not use
if parts are loose or damaged.

Page 2

8. Do not exceed listed weight capacity, evenly
distributed Be aware of dynamic loading!
Sudden load movement may briefly create
excess load causing product failure.
9. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
10. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
11. WARNING: This product contains lead, a chemical
known to the State of California to cause cancer
and birth defects or other reproductive harm.
(California Health & Safety Code , et seq.)

For technical questions, please call 1-888-866-5797.

Item 60723

12. Grounding

TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING
WIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
Do not modify the power cord plug provided with the tool. Never remove the grounding prong from
the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service
facility before use. If the plug will not fit the outlet, have a proper outlet installed by a
qualified el§ 25249.5ectrician.

Grounded Tools: Tools with Three Prong Plugs
2. The grounding prong in the plug is connected through
the green wire inside the cord to the grounding
system in the tool. The green wire in the cord must
be the only wire connected to the tool’s grounding
system and must never be attached to an electrically
“live” terminal. (See 3-Prong Plug and Outlet.)

3-Prong Plug and Outlet

3. The tool must be plugged into an appropriate outlet,
properly installed and grounded in accordance with
all codes and ordinances. The plug and outlet should
look like those in the preceding illustration.
(See 3-Prong Plug and Outlet.)

1. Tools marked with “Grounding Required” have a three
wire cord and three prong grounding plug. The plug
must be connected to a properly grounded outlet.
If the tool should electrically malfunction or break
down, grounding provides a low resistance path to
carry electricity away from the user, reducing the risk
of electric shock. (See 3-Prong Plug and Outlet.)

Double Insulated Tools: Tools with Two Prong Plugs
1. Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies
OSHA requirements and complies with
the applicable standards of Underwriters
Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code.

Outlets for 2-Prong Plug

2. Double insulated tools may be used in either of the
120 volt outlets shown in the preceding illustration.
(See Outlets for 2-Prong Plug.)

Extension Cords
1. Grounded tools require a three wire extension cord.
Double Insulated tools can use either
a two or three wire extension cord.
2. As the distance from the supply outlet increases,
you must use a heavier gauge extension cord.
Using extension cords with inadequately sized wire
causes a serious drop in voltage, resulting in loss of
power and possible tool damage. (See Table A.)

Item 60723

3. The smaller the gauge number of the wire, the
greater the capacity of the cord. For example,
a 14 gauge cord can carry a higher current
than a 16 gauge cord. (See Table A.)
4. When using more than one extension cord to
make up the total length, make sure each cord
contains at least the minimum wire size required.
(See Table A.) If you are using one extension
cord for more than one tool, add the nameplate
amperes and use the sum to determine the
required minimum cord size. (See Table A.)

For technical questions, please call 1-888-866-5797.

Page 3

5. If you are using an extension cord outdoors, make
sure it is marked with the suffix “W-A” (“W” in
Canada) to indicate it is acceptable for outdoor use.

Double Insulated
Canadian Standards Association

6. Make sure the extension cord is properly wired
and in good electrical condition. Always replace
a damaged extension cord or have it repaired
by a qualified electrician before using it.

Underwriters Laboratories, Inc.

V
~
A

7. Protect the extension cords from sharp objects,
excessive heat, and damp or wet areas.
Table A: RECOMMENDED MINIMUM WIRE
GAUGE FOR EXTENSION CORDS* (120/240 VOLT)

NAMEPLATE
AMPERES
(at full load)

EXTENSION CORD
LENGTH
25´ 50´ 75´ 100´ 150´

0 – 2.0

2.1 – 3.4

3.5 – 5.0

5.1 – 7.0

7.1 – 12.0

12.1 – 16.0

16.1 – 20.0

Volts
Alternating Current
Amperes

n0 xxxx/min. No Load Revolutions per Minute (RPM)

* Based on limiting the line voltage drop to five volts at
150% of the rated amperes.

WARNING marking concerning Risk
of Eye Injury. Wear ANSI‑approved
safety goggles with side shields.
Read the manual before
set-up and/or use.
WARNING marking
concerning Risk of Fire.
Do not cover ventilation ducts.
Keep flammable objects away.
WARNING marking concerning
Risk of Electric Shock.
Properly connect power cord
to appropriate outlet.

Specifications
Power Strip Rating

125VAC / 13A

Replacement Bulb

T5 14W
514 lb. evenly distributed as follows:

Maximum Weight
Capacity

Page 4

Bench Top - 220 lb.
Bottom Shelf - 200 lb.
Each Drawer - 25 lb.
Top Shelf - 44 lb.

For technical questions, please call 1-888-866-5797.

Item 60723

Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.

Note: Unless stated otherwise, all connections are
made using Bolts, Washers and Nuts (B). Finger tighten
all connections until assembly is done. Assemble
the Workbench on a flat, level, hard surface.
1. Attach Side Beams (4) to Front (1)
and Back Posts (2).
2. Attach Rubber Feet (3) to the bottom of each post.

4. Attach Side Beam (4) and Side Beam with Power
Strip Opening (4A) to the top 2 holes on Front
Posts and the middle 2 holes on Back Posts.
Note: Side Beam with Power Strip Opening can
be attached to either the right or left side.
5. Attach Power Strip (22) to Side Beam with Power
Strip Opening using U Brackets (F) and Screws (E).

F
E

2
2

F
4
4
3

3
3

Figure A
3. Attach Bottom Beams (5) to Front and Back Posts.

Figure C
6. Attach Top Beams (6) to the top 2 holes on
Front Posts and the middle 2 holes on Back Posts.

Note: Make sure the Front Top Beam carries
the Warning Label and is right-side up.

Figure B
6

Warning
Label
1

Figure D

Item 60723

For technical questions, please call 1-888-866-5797.

Page 5

7. Attach Front (7F) and Back (7B)
Drawer Brackets to Top Beams.

10. Attach Drawer Handle (14) to the
Front Drawer Panel (11) using Bolts, Washers
and Nuts (A). Repeat for second Front
Drawer Panel. Tighten hardware.

11. Lay Drawer Bottom (13) down on a flat
surface. Attach Right (10R) and Left (10L)
Drawer Panels to the Front and Back (12)
Drawer Panels. Repeat for second Drawer.

12. Install the Drawers, making sure the runners on
the Drawers are level with the Drawer Mounts.
14

A
A
11

A
A

10L

Figure E
8. Attach Middle Drawer Mount (8) to
Front and Back Drawer Brackets.

9. Attach Left (9L) and Right (9R) Drawer Mounts
to Front and Back Posts. Tighten hardware.

10R

Figure G
13. Attach left and right Back Upper Posts (15)
to left and right Back Posts.
9L

14. Attach Back Shelf Beam (16B) to Back Upper Posts.

8
9R

15. Attach Left Shelf Beam (17L) and Right
Shelf Beam (17R) to back Shelf Beam.
16. Attach Front Shelf Beam (16F) to
Left and Right Shelf Beams.

17L
16B

Figure F

17R

16F

15
15

Figure H

Page 6

For technical questions, please call 1-888-866-5797.

Item 60723

17. Attach Pegboard (18) to Back Upper
Posts and Middle Drawer Mount using
Bolts, Washers and Nuts (C).

19. Attach Top Shelf (21) to Shelf Beams using Bolts,
Washers and Nuts (D).
D

C
C

Figure K
Figure I
18. Attach Bench Top (19) to Side Beams and
Bottom Shelf (20) to Lower Side Beams using Bolts,
Washers and Nuts (D).

20. Attach Light Fixture (23) to the underside
of the Top Shelf using Bolts (G).
a. Insert a Bolt through each Light Fixture Clip.
b. Thread Bolts through the holes on
the underside of the Top Shelf.
c. Push Light Fixture up into the Clips.

19
D
D
D

D
D

Figure J

Figure L
21. Attach the Light Fixture power cord to the receptacle
at the end of the fixture. It will only connect one way.
Route the cord through the hole in the Pegboard.
Note: Make sure all Shelves are level. Then,
tighten all Bolts and Screws securely.
Item 60723

For technical questions, please call 1-888-866-5797.

Page 7

Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Make sure that the Trigger is in the off‑position and unplug the tool from its
electrical outlet before performing any procedure in this section.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the general
condition of the Workbench. Check for:

2. AFTER USE, wipe external surfaces with clean cloth.

• loose hardware,
• misalignment or binding of moving parts,
• damaged cord/electrical wiring,
• cracked or broken parts, and
• any other condition that may
affect its safe operation.

Replacing Light Bulb
The Light Fixture has a semitransparent
cover over the bulb.
1. Allow Bulb to cool completely, then gently pull straight
down at both ends of the cover and set aside.
2. Remove the Bulb by rotating it 90º, rolling
in a forward or backward direction and
dropping the Bulb straight down.

Page 8

3. With the prongs on either end of the Bulb
vertically aligned, fit the new bulb up into the
slots at the right and left fixture receptacles.
4. Rotate the Bulb 90º again to seat
the bulb. Replace the cover.

For technical questions, please call 1-888-866-5797.

Item 60723

PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Item 60723

For technical questions, please call 1-888-866-5797.

Page 9

Parts List and Diagram

Parts List
Part
1
2
3
4
4A
5
6
7F
7B
8
9L
9R
10L
10R
11
12
13
14

Description

Front Post
Back Post
Rubber Foot
Side Beam
Side Beam with Power Strip Opening
Bottom Beam
Top Beam
Front Drawer Bracket
Back Drawer Bracket
Middle Drawer Mount
Left Drawer Mount
Right Drawer Mount
Left Drawer Panel
Right Drawer Panel
Front Drawer Panel
Back Drawer Panel
Drawer Bottom
Drawer Handle

Qty
2
2
4
3
1
2
2
1
1
1
1
1
2
2
2
2
2
2

Part
15
16F
16B
17L
17R
18
19
20
21
22
23
A
B
C
D
E
F
G

Description

Back Upper Post
Front Shelf Beam
Back Shelf Beam
Left Shelf Beam
Right Shelf Beam
Pegboard
Bench Top
Bottom Shelf
Top Shelf
Power Strip (not shown)
Light Fixture (not shown)
Bolt (M4x10), Washer, Nut
Bolt (M6x10), Washer, Nut
Bolt (M6x16), Washer, Nut
Bolt (M5x25), Washer, Nut
Screw (ST4x9.5)
U Bracket
Bolt (M4x16)

Qty
2
1
1
1
1
1
1
1
1
1
1
8
78
13
12
4
2
2

Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.

Page 10

For technical questions, please call 1-888-866-5797.

Item 60723

Assembly Diagram
21

16B

17L

17R

16F
15
15

18
4A

7B
8

(Under Part 20)

1
1

13
3

12
10L

10L

10R

Item 60723

10R

For technical questions, please call 1-888-866-5797.

Page 11

Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c014 79.156797, 2014/08/20-09:53:02
Instance ID                     : uuid:38fc7a8e-0f38-7f47-bca4-1baecf784178
Original Document ID            : adobe:docid:indd:2947f79c-bab0-11df-a4dc-d1b6dbadcc65
Document ID                     : xmp.id:1063b9e8-156d-41d4-bdf3-ee692dd78433
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:44bb470f-1f0f-49af-b8e1-491f433a7212
Derived From Document ID        : xmp.did:d4843987-a900-4cb2-838c-fa4ad6fdbd32
Derived From Original Document ID: adobe:docid:indd:2947f79c-bab0-11df-a4dc-d1b6dbadcc65
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2014 (Macintosh)
History Changed                 : /
History When                    : 2015:05:04 08:56:35-07:00
Create Date                     : 2015:05:04 08:56:35-07:00
Modify Date                     : 2015:05:04 08:56:45-07:00
Metadata Date                   : 2015:05:04 08:56:45-07:00
Creator Tool                    : Adobe InDesign CC 2014 (Macintosh)
Export Script                   : Export pdf script v3.80
Format                          : application/pdf
Rights                          : Copyright©2012 by Harbor Freight Tools®.  All rights reserved.  No portion of this document or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
Web Statement                   : http://www.harborfreight.com
Marked                          : True
Producer                        : Adobe PDF Library 11.0
Trapped                         : False
Page Count                      : 12
Creator                         : Adobe InDesign CC 2014 (Macintosh)

EXIF Metadata provided by EXIF.tools

Harbor Freight Multipurpose Workbench With Light Product Manual

Navigation menu

Versions of this User Manual:

Views

Navigation