Harman Becker Automotive Systems BE2729 Navigation and Connectivity Box User Manual Display Audio Ext U 33A02U

Harman Becker Automotive Systems, Inc. Navigation and Connectivity Box Display Audio Ext U 33A02U

08 user guide

1
1QUICK GUIDE 9
2APPLICATION-“Map19
3APPLICATION-THE OTHERS 73
4AUDIO SYSTEM 99
5Bluetooth® HANDS-FREE SYSTEM 153
6VOICE COMMAND SYSTEM 185
7VEHICLE INFORMATION 189
8SETUP 195
9REAR VIEW MONITOR SYSTEM 213
INDEX 221
WITH NAVIGATION (2ND SECTION)
TABLE OF CONTENTS
2
1. BASIC INFORMATION BEFORE OPERATION
Introduction
This manual explains the operation of the Display Audio system. Please read
this manual carefully to ensure proper use. Keep this manual in your vehicle at
all times.
The screen shots in this document and the actual screens of the Display Audio
system differ depending on whether the functions and/or a contract existed and
the map data available at the time of producing this document.
The Navigation System is one of the most technologically advanced vehicle ac-
cessories ever developed. The system receives satellite signals from the Global
Positioning System (GPS) operated by the U.S. Department of Defense. Using
these signals and other vehicle sensors, the system indicates your present po-
sition and assists in locating a desired destination.
The navigation system is designed to select efficient routes from your present
starting location to your destination. The system is also designed to direct you
to a destination that is unfamiliar to you in an efficient manner. The system is
developed by “Harman International” using “Navteq” maps. The calculated
routes may not be the shortest nor the least traffic congested. Your own person-
al local knowledge or “short cut” may at times be faster than the calculated
routes.
The navigation system’s database includes Point of Interest categories to allow
you to easily select destinations such as restaurants and hotels. If a destination
is not in the database, you can enter the street address or a major intersection
close to it and the system will guide you there.
The system will provide both a visual map and audio instructions. The audio in-
structions will announce the distance remaining and the direction to turn in ap-
proaching an intersection. These voice instructions will help you keep your eyes
on the road and are timed to provide enough time to allow you to maneuver,
change lanes or slow down.
Please be aware that all current vehicle navigation systems have certain limita-
tions that may affect their ability to perform properly. The accuracy of the vehi-
cle’s position depends on the satellite condition, road configuration, vehicle
condition or other circumstances. For more information on the limitations of the
system, refer to page 66.
DISPLAY AUDIO SYSTEM OWNER’S MANUAL
NAVIGATION SYSTEM
3
1. BASIC INFORMATION BEFORE OPERATION
For safety reasons, this manual indicates items requiring particular attention
with the following marks.
IMPORTANT INFORMATION ABOUT THIS MANUAL
CAUTION
This is a warning against anything which may cause injury to people if the warning is
ignored. You are informed about what you must or must not do in order to reduce the risk
of injury to yourself and others.
NOTICE
This is a warning against anything which may cause damage to the vehicle or its equip-
ment if the warning is ignored. You are informed about what you must or must not do in
order to avoid or reduce the risk of damage to your vehicle and its equipment.
4
1. BASIC INFORMATION BEFORE OPERATION
To use this system in the safest possible
manner, follow all the safety tips shown
below.
This system is intended to assist in reach-
ing the destination and, if used properly,
can do so. The driver is solely responsible
for the safe operation of your vehicle and
the safety of your passengers.
Do not use any feature of this system to
the extent it becomes a distraction and
prevents safe driving. The first priority
while driving should always be the safe op-
eration of the vehicle. While driving, be
sure to observe all traffic regulations.
Prior to the actual use of this system, learn
how to use it and become thoroughly famil-
iar with it. Read the entire Display Audio
system Owner’s manual to make sure you
understand the system. Do not allow other
people to use this system until they have
read and understood the instructions in
this manual.
For your safety, some functions may be-
come inoperable when driving. Unavail-
able screen buttons are dimmed. Only
when the vehicle is not moving, can the
destination and route selection be done.
While driving, listen to the voice instruc-
tions as much as possible and glance at
the screen briefly and only when it is safe.
However, do not totally rely on voice guid-
ance. Use it just for reference. If the sys-
tem cannot determine the current vehicle
position correctly, there is a possibility of
incorrect, late, or non-voice guidance.
The data in the system may occasionally
be incomplete. Road conditions, including
driving restrictions (no left turns, street clo-
sures, etc.) frequently change. Therefore,
before following any instruction from the
system, look to see whether the instruction
can be done safely and legally.
This system cannot warn about such
things as the safety of an area, condition of
streets, and availability of emergency ser-
vices. If unsure about the safety of an ar-
ea, do not drive into it. Under no
circumstances is this system a substitute
for the driver’s personal judgement.
Use this system only in locations where it
is legal to do so. Some states/provinces
may have laws prohibiting the use of video
and navigation screens next to the driver.
SAFETY INSTRUCTION CAUTION
For safety, the driver should not operate
the Display Audio system while he/she
is driving. Insufficient attention to the
road and traffic may cause an accident.
While driving, be sure to obey the traffic
regulations and maintain awareness of
the road conditions. If a traffic sign on
the road has been changed, route guid-
ance may not have the updated informa-
tion such as the direction of a one way
street.
5
1. BASIC INFORMATION BEFORE OPERATION
TABLE OF CONTENTS
6
1. CONTROLS AND FEATURES ........ 10
OVERVIEW BUTTONS ......................... 10
SYSTEM FUNCTION INDEX................. 12
TOUCH SCREEN OPERATION............ 14
1. NAVIGATION OPERATION ............ 20
QUICK REFERENCE ............................ 20
NAVIGATION SYSTEM
FUNCTION INDEX.............................. 23
MAP SCREEN OPERATION................. 25
MAP ICONS........................................... 29
2. DESTINATION SEARCH................. 33
DESTINATION SEARCH....................... 33
3. ROUTE GUIDANCE......................... 42
STARTING ROUTE GUIDANCE ........... 42
ROUTE GUIDANCE .............................. 44
SETTING AND DELETING
THE ROUTE........................................ 46
4. MY DESTINATIONS ........................ 52
REGISTERING A ENTRY...................... 52
DISPLAYING AND EDITING
THE ENTRY INFORMATION.............. 58
SENDING STORED CONTACTS
TO A USB MEMORY .......................... 60
5. NAVIGATION SETTING .................. 61
MAP SETTINGS .................................... 61
ROUTE SETTINGS ............................... 64
6. NAVIGATION SYSTEM
INFORMATION .............................. 66
LIMITATIONS OF THE NAVIGATION
SYSTEM.............................................. 66
MAP INFORMATION............................. 68
1. APPLICATIONS OPERATION........ 74
QUICK REFERENCE............................. 74
PICTURE SLIDESHOW......................... 75
EMAIL..................................................... 77
CALENDAR............................................ 79
2. ENTUNE SERVICE ......................... 80
ENTUNE SERVICE................................ 80
OPERATING NAVIGATION FUNCTION
USING ENTUNE SERVICE................. 83
OPERATING AN APPLICATION
USING ENTUNE SERVICE................. 93
1. AUDIO SYSTEM OPERATION ..... 100
QUICK REFERENCE........................... 100
SOME BASICS..................................... 102
RADIO OPERATION............................ 106
RADIO OPERATION (XM® Satellite
Radio BROADCAST)......................... 112
CD PLAYER OPERATION................... 117
USB MEMORY/iPod OPERATION ...... 123
AUX DEVICE OPERATION ................. 130
Bluetooth® AUDIO OPERATION ......... 132
STEERING SWITCHES ....................... 141
AUDIO SYSTEM
OPERATING HINTS.......................... 144
1QUICK GUIDE
2APPLICATION-Map”
3APPLICATION-THE OTHERS
4AUDIO SYSTEM
7
1
2
3
4
5
6
7
8
9
1. BASIC INFORMATION
BEFORE OPERATION ................ 154
QUICK REFERENCE .......................... 154
HANDS-FREE SYSTEM ..................... 157
CONNECTING A
Bluetooth® PHONE ........................... 161
REGISTERING A ENTRY ................... 165
2. TELEPHONE OPERATION........... 170
CALLING ON A Bluetooth® PHONE ... 170
RECEIVING CALLS ON A
Bluetooth® PHONE ........................... 175
TALKING ON A Bluetooth® PHONE ... 176
3. SHORT MESSAGE FUNCTION .... 179
SHORT MESSAGE FUNCTION.......... 179
1. VOICE COMMAND SYSTEM
OPERATION ................................ 186
VOICE COMMAND SYSTEM.............. 186
1. VEHICLE INFORMATION ............. 190
QUICK REFERENCE .......................... 190
FUEL CONSUMPTION ....................... 191
TIRE PRESSURE WARNING
SYSTEM ........................................... 193
1. SETUP OPERATION .................... 196
QUICK REFERENCE .......................... 196
GENERAL SETTINGS......................... 197
DISPLAY SETTINGS........................... 200
Bluetooth® SETTINGS......................... 202
PHONE SETTINGS ............................. 209
AUDIO SETTINGS............................... 210
VEHICLE SETTINGS........................... 211
1. REAR VIEW MONITOR
SYSTEM ...................................... 214
REAR VIEW MONITOR SYSTEM
OPERATION ..................................... 214
DRIVING PRECAUTIONS
(WITH REAR VIEW MONITOR
GUIDE LINES) .................................. 218
ALPHABETICAL INDEX................... 222
5Bluetooth® HANDS-FREE
SYSTEM
6VOICE COMMAND SYSTEM
7VEHICLE INFORMATION
8SETUP
9REAR VIEW MONITOR
SYSTEM
INDEX
8
1
9
1
2
3
4
5
6
7
8
9
1. OVERVIEW BUTTONS ................. 10
2. SYSTEM FUNCTION INDEX......... 12
3. TOUCH SCREEN OPERATION.... 14
INPUT SCREEN OPERATION .............. 14
LIST SCREEN OPERATION ................. 16
1CONTROLS AND FEATURES
QUICK GUIDE
10
1. CONTROLS AND FEATURES
1. OVERVIEW BUTTONS
zThe actual design and button position may differ depending on the vehicle. For
details, see Section 3 of “Owner’s Manual”.
No. Name Function Page
Touch screen
display
By touching the screen with your finger, you can
control the selected functions. 14
Disc slot Insert a disc into this slot. The CD player turns on
immediately. 117
“TUNE SCROLL”
knob
Turn this knob to select radio station bands,
tracks and files. Also, the knob can be used for
selection from the list display.
103
“AUDIO” button Press this button to access the audio system. The
audio system turns on in the last mode used.
100, 102,
103
button* Press this button to pause or resume playing the
music.
button Press this button to access the Bluetooth®
hands-free system. 154
“SETUP” button Press this button to customize the function set-
tings. 196
11
1. CONTROLS AND FEATURES
1
QUICK GUIDE
*: If equipped
“SEEK/TRACK
button
Press the “ ” or “ ” button to seek up or down for
a radio station, or to access a desired track or file.
107, 114,
119, 121,
124, 137
“CAR” button* Press this button to access the vehicle informa-
tion system. 190
“APPS” button Press to display a list of applications. 20, 74
“PWR VOL” knob Press this knob to turn the audio system on and
off, and turn it to adjust the volume. 102
button Press this button to eject a disc. 117
No. Name Function Page
12
1. CONTROLS AND FEATURES
2. SYSTEM FUNCTION INDEX
To access the application system, press
the “APPS” button. The “Applications”
menu screen will be displayed. The driver
can use the navigation system and the oth-
er applications. For details, see page 19,
73.
To access the audio system, press the
“AUDIO” button. The audio control screen
will be displayed. Audio sources: Radio,
CDs, iPod, USB, AUX and Bluetooth® au-
dio. For details, see page 99.
To access the Bluetooth® hands-free sys-
tem, press the button. The driver
can make or receive phone calls without
taking their hands off the steering wheel.
For details, see page 153.
To access the voice command system,
press the switch on the steering
wheel. The driver can operate the Display
Audio system by giving a command. For
details, see page 185.
APPLICATION SYSTEM
AUDIO SYSTEM
Bluetooth® HANDS-FREE
SYSTEM
VOICE COMMAND SYSTEM
13
1. CONTROLS AND FEATURES
1
QUICK GUIDE
To access the vehicle information system,
press the “CAR” button. Fuel consump-
tion and tire pressure can be checked. For
details, see page 189.
To customize the function settings, press
the “SETUP” button. The interface lan-
guage can also be changed from the setup
menu. For details, see page 195.
Shifting into the “R” position will automati-
cally show the view behind the rear of the
vehicle on the display screen. For details,
see page 213.
VEHICLE INFORMATION
(IF EQUIPPED)
SETUP
REAR VIEW MONITOR SYSTEM
14
1. CONTROLS AND FEATURES
3. TOUCH SCREEN OPERATION
zTo prevent damage to the screen, lightly
touch screen buttons on the screen with
the finger. When a screen button on the
screen is touched, a beep sounds. (To set
a beep sound, see page 197.)
zDo not use objects other than your finger
to touch the screen.
1Touch the keys directly to input letters
or numbers.
: Touch to delete one letter. Touch
and hold to continue deleting letters.
2Touch “OK”.
This system is operated mainly by the
screen buttons on the screen.
NOTICE
To prevent the 12-volt battery from being
discharged, do not leave the system on
longer than necessary when the engine
is not running.
INFORMATION
If the system does not respond to a
touch on a screen button, move the fin-
ger away from the screen and then
touch it again.
Dimmed screen buttons cannot be oper-
ated.
Wipe off fingerprints using a glass clean-
ing cloth. Do not use chemical cleaners
to clean the touch screen.
The displayed image may become
darker and moving images may be
slightly distorted when the display is
cold.
Under extremely cold conditions, the
screen may not be displayed and the
data input by a user may be deleted.
Also, the screen buttons may be harder
than usual to depress.
When you look at the screen through
polarized material such as polarized
sunglasses, the screen may be dark and
hard to see. If so, look at the screen
from different angles, adjust the screen
settings (See “DISPLAY SETTINGS” on
page 200.), or take off your sunglasses.
INPUT SCREEN OPERATION
When searching for an address or a
name, letters and numbers can be in-
put via the screen.
INFORMATION
Letters cannot be input while driving.
INPUTTING LETTERS AND
NUMBERS
INFORMATION
When a character is input, a hint will
appear displaying a possible match for
the word to be searched.
Currently unavailable screen buttons will
be dimmed.
When an entry is too long to be dis-
played in the input field, the last section
of the input text will be displayed with
the initial section displayed as “...”.
If the vehicle starts moving while letters
are being input, a warning message will
be displayed and letters cannot be input.
Touch “Previous” to return to the previ-
ous screen.
15
1. CONTROLS AND FEATURES
1
QUICK GUIDE
CHANGING BETWEEN LOWER
CASE AND UPPER CASE
1Touch or .
: Touch to enter in lower case.
: Touch to enter in upper case.
zEach time or is touched,
input will change between upper case and
lower case input.
INPUTTING SYMBOLS
1Touch .
2Touch ( ) or .
X ( ) keyboard layout
Xkeyboard layout
3Touch the symbol keys directly to input
symbols.
INFORMATION
In the following situations, the input
mode will automatically change between
upper and lower case.
When the keyboard layout is
changed to upper case input, the lay-
out will automatically change back to
lower case input after one letter has
been entered.
When “/”,“&”,“.” or “(” is input, the
keyboard layout will automatically be
changed to upper case input.
When all characters are deleted, the
keyboard layout will automatically
change to upper case input.
16
1. CONTROLS AND FEATURES
1Enter letters.
zIf a candidate entry text displayed in the
input field is what is desired, touch “OK.
zTouching displays the candidate
entry text list. The number of matching
items is shown. Up to 300 items are dis-
played.
zThe list will be displayed automatically, if
the number of matching entries is 5 or
less.
2Touch desired item.
or : Touch to shift to the next or
previous page.
zBy touching and holding this screen but-
ton, the screen can be scrolled up or
down. Scrolling will automatically stop
when the top/bottom of the list is reached.
:Touch to have entries that are too
long to fit in the current field scrolled
automatically from right to left.
ENTERING FROM THE LIST OF
MATCHING ENTRIES
On certain screens, a candidate entry
text or word prediction list based on the
input letters will be displayed. The de-
sired item can be selected and en-
tered.
LIST SCREEN OPERATION
When a list is displayed, use the appro-
priate screen button to scroll through
the list.
INFORMATION
While driving, changing pages will be
limited.
:This indicates the displayed screen’s
position.
17
1. CONTROLS AND FEATURES
1
QUICK GUIDE
1Touch one of the character screen but-
tons.
CHARACTER JUMP BUTTONS
IN LISTS
Some lists contain character screen
buttons, ABC”,“DEF” etc., which al-
low a direct jump to list entries that be-
gin with the same letter as the
character screen button.
INFORMATION
Every time the same character screen
button is touched, the list starting with
the subsequent character is displayed.
18
1. QUICK REFERENCE .................... 20
2. NAVIGATION SYSTEM
FUNCTION INDEX ...................... 23
3. MAP SCREEN OPERATION......... 25
TO DISPLAY MAP SCREEN ................. 25
MAP SCREEN OPERATION ................. 25
4. MAP ICONS................................... 29
POI* ICONS ........................................... 29
1. DESTINATION SEARCH............... 33
DESTINATION SEARCH ON THE
“My Destinations” SCREEN................. 33
DESTINATION SEARCH ON THE
“Enter Destination” SCREEN............... 35
1NAVIGATION OPERATION
2DESTINATION SEARCH
*: Point of Interest
2
19
1
2
3
4
5
7
8
9
6
1. STARTING ROUTE
GUIDANCE .................................. 42
STARTING ROUTE GUIDANCE
SCREEN ............................................. 42
SETTING THE ROUTE ......................... 43
2. ROUTE GUIDANCE....................... 44
ROUTE GUIDANCE SCREEN .............. 44
VOICE GUIDANCE ............................... 45
3. SETTING AND DELETING
THE ROUTE................................. 46
SETTING FROM THE “Options
SCREEN ............................................. 46
ADDING DESTINATIONS..................... 49
DETOURING A SEGMENT ON THE
ROUTE................................................ 51
1. REGISTERING A ENTRY .............. 52
REGISTERING A NEW ENTRY............ 52
2. DISPLAYING AND EDITING
THE ENTRY
INFORMATION............................ 58
DISPLAYING AND EDITING THE
ENTRY INFORMATION...................... 58
3. SENDING STORED CONTACTS
TO A USB MEMORY ................... 60
SENDING STORED CONTACTS TO A
USB MEMORY.................................... 60
1. MAP SETTINGS ............................ 61
SETTING THE MAP .............................. 61
2. ROUTE SETTINGS ....................... 64
SETTING THE ROUTE OPTIONS ........ 64
1. LIMITATIONS OF THE
NAVIGATION SYSTEM .............. 66
2. MAP INFORMATION..................... 68
3ROUTE GUIDANCE
4MY DESTINATIONS
5NAVIGATION SETTING
6NAVIGATION SYSTEM
INFORMATION
APPLICATION-“Map”
20
1. NAVIGATION OPERATION
1. QUICK REFERENCE
X“Applications” menu screen
The navigation application and several other applications can be accessed by
pressing the “APPS button.
When the “APPS” button is pressed, the “Applications” menu screen that was last
displayed is returned to. Touch to display the “Applications” menu screen.
No. Function Page
Press to display a list of applications.
“Map” provides the user with navigation, route calculation, destination
entry (manually or via voice recognition), turn by turn directions, and
real-time traffic.
25
Touch to view pictures stored on a USB memory. 75
Touch to display Emails. 77
Touch to access the connected phone’s calendar, tasks and notes. 79
Touch to access the applications. 83, 85, 93
Touch to close or delete the applications. 93, 94
Touch to shift to the next or previous page.
21
1. NAVIGATION OPERATION
2
APPLICATION-“Map”
X“Navigation” menu screen
To display the “Navigation” menu screen, touch “Dest” on the map. From this
screen, destinations can be entered and route-related settings can be changed.
No. Function Page
Touch to display the “My Destinations” screen.
A destination can be entered by selecting an item from the list of stored
destinations, previous destinations or the addresses from the connect-
ed phone’s phone book.
33
Touch to display the “Enter Destination” screen.
A destination can be entered by address, POI or using advanced op-
tions. It can also be added as a waypoint to a destination.
35, 49
Touch to display the “Traffic Messages” screen.
Traffic messages function is using Entune service.
It contains a list of traffic messages relating to the set route, all traffic
messages and warnings.
86
Touch to display the “Route Options” screen.
The route preferences, avoidance criteria and traffic messages func-
tion can be adjusted.
64
Touch the corresponding icon to change to the “My Destinations”, “En-
ter Destination”, “Traffic Messages” or “Route Options” screen.
33, 35, 49,
64, 86
22
1. NAVIGATION OPERATION
XOverview guidance screen
No. Function Page
This symbol indicates a map layout. Touching this symbol changes the
map layout. 28
Displays the distance, the estimated travel time to the destination, or
the estimated arrival time at the destination. 44
Displays traffic information on the route. 86
Displays the distance to the next turn with the arrow indicating the turn
direction. 44
Touch to display the “Options” screen. 46
Touch to display the “Navigation” menu screen. 21
Displays the current street name. 44
Touch to display the “Applications” menu screen. 20, 74
Touch to hear voice guidance and/or adjust the volume of voice guid-
ance. 45
Touch to change the map scale. 27
23
2
APPLICATION-“Map”
1. NAVIGATION OPERATION
2. NAVIGATION SYSTEM FUNCTION INDEX
XMap
XRoute guidance
Displaying maps Page
Viewing the map screen 25
Displaying the current vehicle position 25
Viewing the current vehicle position vicinity map 27
Changing the scale 27
Changing the map layout 27
Displaying Point of Interest Icons 29
Viewing traffic messages 86
Searching destination Page
Searching the destination 33
Setting the entry registered with the system as the destination 33
Before starting route guidance Page
Recalculating the route 43
Viewing alternative routes 42
Starting route guidance 42
Before starting or during route guidance Page
Viewing the route 46
Adding destinations 49
Recalculating the route 47
Changing the estimated travel/arrival time display 63
24
1. NAVIGATION OPERATION
XMemory point
During route guidance Page
Stopping route guidance 46
Adjusting route guidance volume 45
Displaying the entire route map 46
Memory point Page
Registering the entry 52
Editing the entry 58
Loading the entry from external devices 56
25
2
APPLICATION-“Map”
1. NAVIGATION OPERATION
3. MAP SCREEN OPERATION
1Press the APPS” button.
zWhen the “APPS” button is pressed, the
“Applications” menu screen that was last
displayed will be returned to. Touch
until the “Applications” menu
screen is displayed.
2Touch “Map”.
3Touch “Confirm”.
zAfter about a few seconds, the “CAU-
TION” screen automatically switches to
the map screen.
zThe current vehicle position mark
appears in the center of the map screen.
TO DISPLAY MAP SCREEN INFORMATION
The “CAUTION” screen will be displayed
when the screen is changed to the map
screen for the first time after the engine
switch has been in the “ACC” or “ON”
position.
If “Map” is touched while the map is
loading or an application is in use, a
pop-up window will be displayed. When
the loading process is complete, the
map screen will be displayed.
MAP SCREEN OPERATION
CURRENT VEHICLE POSITION
DISPLAY
When starting the navigation system,
the current position is displayed first.
This screen displays the current vehi-
cle position and a map of the surround-
ing area.
26
1. NAVIGATION OPERATION
CURRENT LOCATION AND GPS IN-
FORMATION
1Touch “Options on the map.
2Touch “Location & GPS Informa-
tion”.
3An information screen will be dis-
played.
zOn this screen, the following information is
displayed.
INFORMATION
The vehicle icon can be changed. (See
page 61.)
While driving, the current vehicle posi-
tion mark is fixed on the screen and the
map moves.
The current position is automatically set
as the vehicle receives signals from the
GPS (Global Positioning System). If the
current position is not correct, it is auto-
matically corrected after the vehicle
receives signals from the GPS.
After 12-volt battery disconnection, or on
a new vehicle, the current position may
not be correct. As soon as the system
receives signals from the GPS, the cor-
rect current position is displayed.
Current location, geo-coordinates and
GPS information are displayed.
No. Information
The information provided varies,
depending whether the road cur-
rently being travelled on is a free-
way or a street.
Latitude and Longitude
Amount of available satellites
and the altitude.
27
1. NAVIGATION OPERATION
2
APPLICATION-“Map”
zIf a finger is continuously held on the
screen, the map will continue scrolling in
that direction until the finger is removed.
zA street name or geo-coordinates of the
touched point will be shown, depending
on the scale of the map.
zAfter the screen is scrolled, the map
remains centered at the selected location
until another function is activated. The cur-
rent vehicle position mark will continue to
move along your actual route and may
move off the screen. When is
touched, the current vehicle position mark
returns to the center of the screen and the
map moves as the vehicle proceeds along
the designated route.
zWhen the scroll feature is used, the cur-
rent vehicle position mark may disappear
from the screen. Touch to display
the current vehicle position on the map
screen.
MAP SCALE
1Touch “+” or “-” to change the scale of
the map screen.
SCREEN SCROLL OPERATION
When any point on the map is touched,
that point moves to the center of the
screen and is shown by the cursor
mark .
zWhen Calculate is touched, the start-
ing route guidance screen is displayed.
(See page 42.)
zWhen “Save” is touched, the point is
registered in the “Stored” list on the “My
Destinations” screen. (See page 54.)
MAP CONFIGURATIONS
Any of the following map configura-
tions can be selected.
INFORMATION
The scale range is from 150 ft to 250
miles.
After the scale has been changed, the
new scale indicator will be displayed in
the upper left area of the screen for a
while.
28
1. NAVIGATION OPERATION
MAP LAYOUT
1Touch or .
2Touch the desired map layout.
“3D Heading”: Touch to display 3D map.
The direction of vehicle travel is always up.
“2D Heading”: Touch to display 2D map.
The direction of vehicle travel is always up.
“2D North”: Touch to display 2D map. Re-
gardless of the direction of vehicle travel,
north is always up.
X3D Heading
X2D Heading
X2D North
The map layout can be changed from
“3D Heading”,“2D Heading” or “2D
North”.
zMap layout can be also changed by
“Map Settings”. (See page 61.)
29
2
APPLICATION-“Map”
1. NAVIGATION OPERATION
4. MAP ICONS
zPOI icons are displayed on the map.
LIST OF POI ICONS
XPublic
POI ICONS
DISPLAY POI ICONS
Points of Interest such as gas stations
and restaurants can be displayed on
the map screen. Their location can
also be set as a destination.
zYou can select a particular type of Point
of Interest displayed on the screen.
(See page 61.)
Icon Name
Library
College/University
School
Tourist office
Cemetery, funeral director
Government Office, Institution,
City hall, Community gen.
Community
Court house
Place of worship
Accommodation, Hotel/Motel
Pharmacy
Convention Center, Exhibition
Center
Finance, Bank
Cash Dispenser
Post Office
Business, B. General, B. facility
Medical, Doctor, Health & Care
Ambulance, Hospital/Polyclinic
Fire Station
Police Station
Phone Box, Communication
Dentist
Veterinarian
Icon Name
30
1. NAVIGATION OPERATION
XTraffic
XClubbing
XSport
Icon Name
Car Dealer/Repairer, Repair Fa-
cility, Repair General, Car Wash,
Tire Repair
Car Dealer
Highway Exit
Airport, Dep. /Arrival, Ground, In-
ternational, Domestic
Bus Terminal, Bus Stop, Trans-
portation, Public Transp. Stop,
Transport general
Railway Station
Metropolitan Train
Gas Station
Rent-a-Car,-Facility, -Parking
Ferry Terminal
Parking, Open Parking Area, P.
Area general
Parking Garage
Open P.A. P+P
Rest Area
Motoring Organization, Automo-
bile Club
Mover, Moving Company
Motorcycle Dealer
Icon Name
Multiple POI
Bar, Nightlife
Leisure, Cultural Center, The-
ater, Music Center, Concert Hall
Cinema
Casino
Cafe/Bar, Cafe
Restaurant, French, Belgian,
Chinese, German, Greek, Vege-
tarian, Fast Food, Grill, Sea
Food, Sandwich, Steak...
Icon Name
Sport, Sport General, sport activ-
ities
Golf Course
Race Track
Stadium, Sports Center, Hippo-
drome
Water Sports
Bowling
Icon Name
31
1. NAVIGATION OPERATION
2
APPLICATION-“Map”
XLeisure
Icon Name
Amusement Park
Winery
Museum
Shopping, Market Place, Shop-
ping Center, Factory Outlet
Shop, Department Store, Drive-
through-bottle-shop
Tourist Attractions, Important
Tourist Attractions
Park/Recreational Area
Yacht Basin, Harbour
Camping Ground
Grocery Store
Historical Monument
RV Park, Camping
Bookstore
Hair & Beauty
Photography
Shoestore
Wine & Liquor
Clothing
Cleaning & Laundry
Icon Name
32
1. NAVIGATION OPERATION
1Touch the desired POI icon on the
map.
2Touch .
XOne POI
XMultiple POI
3POI information will be displayed.
DISPLAYING POI
INFORMATION
zWhen “Calculate is touched, the start-
ing route guidance screen is displayed.
(See page 42.)
zWhen Save” is touched, the point is
registered in the “Stored” list on the “My
Destinations” screen. (See page 54.)
zWhen is touched, the registered
telephone number is called.
33
2
APPLICATION-“Map”
2. DESTINATION SEARCH
1. DESTINATION SEARCH
1Touch “Dest” on the map.
2Touch “My Destinations.
zThe “My Destinations” screen can be dis-
played by touching on any of the
“Navigation” screens.
3Touch the tab for the desired method.
zPlease refer to the following pages for a
description of each operation.
1Touch “Stored” on the “My Destina-
tions” screen.
2Touch the desired entry.
3The starting route guidance screen will
be displayed. (See page 42.)
DESTINATION SEARCH ON
THE “My Destinations”
SCREEN
There are several ways to search a
destination.
(a)Destination search by stored desti-
nations
(b)Destination search by previous des-
tinations
(c)Destination search by the connect-
ed phone’s phone book
DESTINATION SEARCH BY
“Stored”
Destinations can be selected from the
destinations registered with the sys-
tem. To use this function, it is neces-
sary to register the entry. (See page
52.)
zTouch to display and edit the entry
information. (See page 58.)
INFORMATION
If “Home” has not been registered, a
message will be displayed and the
setting screen will automatically
appear. (See page 53.)
34
2. DESTINATION SEARCH
1Touch “Previous” on the “My Destina-
tions” screen.
2Touch the desired entry.
3The starting route guidance screen will
be displayed. (See page 42.)
1Touch “Phone Book” on the “My Des-
tinations” screen.
2Touch the desired entry.
3The starting route guidance screen will
be displayed. (See page 42.)
DESTINATION SEARCH BY
“Previous”
A destination can be selected from the
past destination list.
zTouch to display and edit the entry
information. (See page 58.)
INFORMATION
The list can contain a maximum of
100 entries. When the maximum is
reached, the oldest destination is
deleted, making room for the new des-
tination to be stored in the list.
DESTINATION SEARCH BY
“Phone Book”
A destination can be set using the
address of a contact from the phone
book of a connected cellular phone.
Before using this function, connect a
Bluetooth® phone with a phone profile.
(See page 203.)
If a contact does not have address in-
formation stored, the entry will be
dimmed.
zTouch Search Contact” to search by
the contact's name.
zTouch to display and edit the entry
information. (See page 58.)
INFORMATION
“Search Contact cannot be oper-
ated while driving.
35
2. DESTINATION SEARCH
2
APPLICATION-“Map”
1Touch “Dest” on the map.
2Touch “Enter Destination”.
zThe “Enter Destination” screen can be dis-
played by touching on any of the
“Navigation” screens.
3Touch the tab for the desired method.
zPlease refer to the following pages for a
description of each operation.
1Touch “Address” on the “Enter Desti-
nation” screen.
2Touch “Country”.
3Touch the desired country.
4Touch “State” and enter the desired
state (USA and Mexico) or province
(Canada).
DESTINATION SEARCH ON
THE “Enter Destination”
SCREEN
There are several ways to search a
destination.
(a)Destination search by address
(b)Destination search by POI
(c)Destination search by advanced
DESTINATION SEARCH BY
“Address”
A destination can be searched using a
city name or zip code.
36
2. DESTINATION SEARCH
5Touch “City” or “Zip” to enter the city
name or zip code.
zWhen either a “City or “Zip is entered,
the other will be entered automatically.
6Touch “Street to enter the street
name.
7Touch “No.” to enter the street No.
8Touch “Calculate Route”.
9The starting route guidance screen will
be displayed. (See page 42.)
SEARCHING “By Category”
1Touch “POI” on the “Enter Destina-
tion” screen.
2Touch “By Category”.
3Touch the desired item to search the
area. (See page 38.)
4Touch the desired category.
INFORMATION
“Calculate Route” can be selected
once a “City” or “Zip” has been
entered. If “Calculate Route” is
touched when only “City” or “Zip has
been entered, a route search starts with
the center of the city entered as the des-
tination.
While driving, screen buttons other than
“Country” cannot be selected.
DESTINATION SEARCH BY
“POI”
POIs in a specific area can be
searched by category, name or from
the map.
37
2. DESTINATION SEARCH
2
APPLICATION-“Map”
5Touch for the desired item.
zIf you touch the desired item, the starting
route guidance screen will be displayed
directly. (See page 42.)
6Touch “Calculate”.
7The starting route guidance screen will
be displayed. (See page 42.)
SEARCHING “By Name”
1Touch “POI on the “Enter Destina-
tion” screen.
2Touch “By Name” on the “POI”
screen.
3Touch the desired item to search the
area. (See page 38.)
4Input POI name.
5Touch “OK”.
6Follow the steps “SEARCHING “By
Category”” from “STEP 5”. (See page
36.)
zWhen “Save” is touched, the point is
registered in the “Stored” list on the “My
Destinations” screen. (See page 54.)
zWhen is touched, the registered
telephone number is called.
INFORMATION
The POI search result list is sorted by
distance to the POI. The distance can be
sorted by the following methods:
When the search area is set to “At
Current Position”,“Around” or
“Along Route”, the distance will be
calculated from the current position to
the POI.
When the search area is set to “At
Destination”, the distance will be
calculated from the destination to the
POI.
INFORMATION
Searching “By Name” cannot be
operated while driving.
38
2. DESTINATION SEARCH
SELECTING “By Map”
1Touch “POI on the “Enter Destina-
tion” screen.
2Touch “By Map on the “POI” screen.
3Touch the desired item to search the
area. (See page 38.)
4Touch the desired POI icon on the
map.
5Follow the steps “SEARCHING “By
Category”” from “STEP 5”. (See page
36.)
SELECTING THE SEARCH AREA
1Touch “By Category”,“By Name or
“By Map.
2Touch the desired item to search the
area.
“At Current Position”: Around the cur-
rent position
“Around: Around the defined country
(See page 39.)
“At Destination”: Around the main desti-
nation
“Along Route”: Along the current route
INFORMATION
Depending on the current map scale,
not all POI icons will be available for
selection.
INFORMATION
When route guidance is not in use, “At
Destination” and Along Route” can-
not be selected.
When “At Destination” is selected,
POIs around the destination will be
searched. POIs around waypoints will
not be searched.
39
2. DESTINATION SEARCH
2
APPLICATION-“Map”
XSelecting “Around” area
1Touch “Country” to select a country.
2Touch “State and enter the desired
state (USA and Mexico) or province
(Canada).
3Touch “City” or “Zip” to enter the
name or zip code.
zWhen either a “City” or “Zip” is entered,
the other will be entered automatically.
4Touch “Define as Search Area”.
ONLINE SEARCH
FUEL PRICES
If you select “Around”, touch “De-
fine” to select the desired search area.
INFORMATION
If only country is selected, a countrywide
POI search is possible.
A destination can be selected via En-
tune service. For detailed information
about “Online Search”, see page 83.
Fuel Prices function is using Entune
service. It enables the navigation sys-
tem to display current fuel prices and
gas station locations, which can be set
as a destination if desired.
For detailed information about “Fuel
Prices”, see page 85.
40
2. DESTINATION SEARCH
1Touch “Advancedon the “Enter Des-
tination” screen.
2Touch the desired method to search
the destination.
zPlease refer to the following pages for a
description of each operation.
SELECTING ON MAP
1Touch “Select Point on Map” on the
“Advanced” screen.
2Touch the desired point on the map.
3Touch “Calculate”.
4The starting route guidance screen will
be displayed. (See page 42.)
DESTINATION SEARCH BY
“Advanced”
zWhen “Save” is touched, the point is
registered in the “Stored” list on the “My
Destinations” screen. (See page 54.)
41
2. DESTINATION SEARCH
2
APPLICATION-“Map”
ENTER GEO-COORDINATES
1Touch “Enter Geo-coordinateson
the “Advanced” screen.
2Touch “N” or “S”.
3Input the latitude (Degreesq, Minutes’,
Seconds”).
4Touch “W” or “E.
5Input the longitude (Degreesq, Min-
utes’, Seconds”).
6Touch “OK.
7Touch “Calculate”.
8The starting route guidance screen will
be displayed. (See page 42.)
ENTER INTERSECTION
1Touch “Enter Intersection” on the
“Advanced” screen.
2Touch “Country” to select a country.
3Touch “State” and enter the desired
state (USA and Mexico) or province
(Canada).
4Touch “City” or “Zip to enter the city
name or zip code.
5Touch “Street” to input the name of
the first intersecting street and then
touch “OK”.
6Touch “Street” to input the name of
the second intersecting street and then
touch “OK”.
7Touch “Start Calculation”.
8The starting route guidance screen will
be displayed. (See page 42.)
Geo coordinates can be entered in
DMS format (Degreesq, Minutes’, Sec-
onds”). Only coordinate values that
can potentially exist are able to be en-
tered. Impossible coordinate values
and their relevant screen buttons will
be dimmed.
zWhen “Save” is touched, the point is
registered in the “Stored” list on the “My
Destinations” screen. (See page 55.)
INFORMATION
If a destination that is not located on a
road is set, the vehicle will be guided to
the point on a road nearest to the desti-
nation.
This function cannot be operated while
driving.
42
3. ROUTE GUIDANCE
1. STARTING ROUTE GUIDANCE
1Touch “Start”.
2Starts route guidance. (See page 44.)
1Touch one of the three recommended
routes to select it.
2Start route guidance. (See page 44.)
STARTING ROUTE
GUIDANCE SCREEN
After searching the destination, the
starting route guidance screen will be
displayed.
According to the setting, either the nor-
mal screen or route alternatives screen
will be displayed. (See page 64.)
CAUTION
Be sure to obey traffic regulations and
keep road conditions in mind while driv-
ing. If a traffic sign on the road has been
changed, the route guidance may not
indicate such changed information.
NORMAL SCREEN
The recommended route will be dis-
played on the map.
z“Preferences: Touch to adjust the
route preferences before starting the
route guidance. (See page 43.)
z“Avoid”: Touch to adjust the avoidance
criteria before starting the route guid-
ance. (See page 43.)
INFORMATION
The default recommended route can be
changed. (See pages 43 and 64.)
The arrival time or the remaining time
will be displayed in the upper right area
of the map. Each time the area is
touched, the display switches between
displaying the arrival time and remaining
time.
Distance of the entire route is displayed
on the map.
The starting route guidance screen will
always be displayed in 2D North.
ROUTE ALTERNATIVES
SCREEN
Three recommended routes are dis-
played on the map.
z“Avoid”: Touch to adjust the avoidance
criteria before starting the route guid-
ance. (See page 43.)
INFORMATION
The arrival time and distance of the
entire route will be displayed in the list.
The starting route guidance screen will
always be displayed in 2D North.
43
3. ROUTE GUIDANCE
2
APPLICATION-“Map”
1Touch “Preferences” on the starting
route guidance screen.
2Touch the desired item.
“Fast Route”: Touch to calculate the fast-
est route.
“Short Route”: Touch to calculate the
shortest route.
“Ecological Route”: Touch to calculate
an ecological route.
3The route will be recalculated.
1Touch “Avoid” on the starting route
guidance screen.
2Touch the desired item.
“Avoid Freeways”: Touch to avoid
freeways.
“Avoid Toll Roads”: Touch to avoid toll
roads.
“Avoid Tunnels”: Touch to avoid tun-
nels.
“Avoid Ferries”: Touch to avoid ferries.
“Avoid Border Crossings”: Touch to
avoid border crossings.
3Touch .
4The route will be recalculated.
SETTING THE ROUTE
SETTING THE ROUTE
PREFERENCES
SETTING THE AVOIDANCE
CRITERIA
INFORMATION
Setting the route preference and avoid-
ance can be also changed from the
“Route Options” screen. (See page 64.)
44
3. ROUTE GUIDANCE
2. ROUTE GUIDANCE
zOn this screen, the following information is
displayed.
SIGNPOSTS
LANE RECOMMENDATION
ROUTE GUIDANCE SCREEN
While guiding the route, the following
screen will be displayed.
No. Information
Distance and travel/arrival time to
the destination
Traffic message on the route (See
page 86.)
The colored section of the bar re-
duces as the vehicle approaches
the next turn
Distance to the next turn with the ar-
row indicating the turn direction
The name of the road currently be-
ing travelled on
Guidance route
Current position
When approaching the turn, a signpost
will automatically be displayed.
When approaching a maneuver, the
lane recommendation will automatical-
ly be displayed.
INFORMATION
If the vehicle goes off the guided route,
the route will be recalculated.
For some areas, the roads have not
been completely digitized in our data-
base. For this reason, the route guid-
ance may select a road that should not
be traveled on.
The above items will be displayed
depending on the map scale.
The displaying of the above items can
be switched off. (See page 61.)
45
3. ROUTE GUIDANCE
2
APPLICATION-“Map”
zWhen is touched while route guid-
ance is active, the last navigation
announcement will be repeated.
zAfter touching , touch “+ or “- to
adjust the volume level of the navigation
announcements.
zAfter touching “+” or “-”, short audible
information will be given to control the cur-
rent volume level (e.g. turn up/turn down).
VOICE GUIDANCE
The voice guidance provides various
messages as you approach an inter-
section, or other points where maneu-
vering the vehicle is necessary.
INFORMATION
The street names may not be pro-
nounced correctly or clearly due to the
text to-speech function.
On freeways, interstates or other high-
ways with higher speed limits, the voice
guidance will be made at earlier points
than on city streets in order to allow time
to maneuver the vehicle.
If the system cannot determine the cur-
rent vehicle position correctly (in cases
of poor GPS signal reception), the voice
guidance may be early or delayed.
CAUTION
Be sure to obey the traffic regulations
and keep the road condition in mind
especially when you are driving on IPD
roads. The route guidance may not have
the updated information such as the
direction of a one way street.
46
3. ROUTE GUIDANCE
3. SETTING AND DELETING THE ROUTE
1Touch “Options.
2Touch the desired items.
zOn this screen, the following functions can
be operated.
Routes can be checked, changed and
recalculated during route guidance.
SETTING FROM THE
“Options” SCREEN
Checking and setting routes is mainly
performed from the “Options” screen.
No. Function
Touch to change the map setting.
(See page 61.)
Touch to stop the current route guid-
ance.
Touch to set the route preferences
and the avoidance criteria for the
route calculation. (See page 47.)
(The current status is displayed on
the right of the item.)
Touch to display a list of the different
segments of the route. It is also pos-
sible to define a detour. (See page
47.) (The current status is displayed
on the right of the item.)
Touch to display the complete route.
Touch to block a fixed distance on
the road ahead. (See page 48.) (The
current status is displayed on the
right of the item.)
Touch to display the current loca-
tion, geo-coordinates and GPS in-
formation. (See page 26.)
Touch to display the destination’s in-
formation. (See page 48.)
47
3. ROUTE GUIDANCE
2
APPLICATION-“Map”
1Touch “Route Options For Current
Routeon the “Options” screen.
2Touch the desired item to change the
route setting.
“Preferences”: Touch to adjust the route
preferences. (See page 43.)
“Avoid”: Touch to adjust the avoidance
criteria. (See page 43.)
3The route will be recalculated.
1Touch “Route List” on the “Options
screen.
2Touch the desired item to display the
segment.
zGuidance arrow, street name, distance to
the point are displayed.
3The detail of the segment is displayed.
or : Touch to display the next or pre-
vious segment.
SETTING THE ROUTE
PREFERENCE OR AVOIDANCE
CRITERIA
DISPLAYING THE ROUTE LIST
A list of the different segments of the
route can be displayed.
zTouch “Detour” to detour the desired
segment. (See page 51.)
48
3. ROUTE GUIDANCE
1Touch “Block Road Ahead” on the
“Options” screen.
2Touch the desired item to select the
desired detour distance.
“Deactivate Block Road Ahead: Touch
to deactivate the function.
“Block Next 1 mi” ~ “Block Next 12mi”:
Touch to detour the next 1 mile ~ 12 miles
of the current route (road).
z“Deactivate Block Road Ahead” can be
selected when the block road ahead func-
tion has been activated.
3The route will be recalculated.
zA blocked route will be marked in the map.
zAfter the blocked route has been
detoured, the block road ahead function
will automatically be deactivated.
1Touch “Destination Information” on
the “Options” screen.
2The destination information screen will
be displayed.
zOn this screen, the following information is
displayed.
BLOCK ROAD AHEAD
A fixed distance on the road ahead can
be blocked.
DISPLAYING THE
DESTINATION INFORMATION
The destination information is dis-
played.
No. Information
Address of destination
Selected route preference
Selected avoidance criteria
Arrival time, remaining time and
distance to destination
Address of each waypoint (if en-
tered)
49
3. ROUTE GUIDANCE
2
APPLICATION-“Map”
1Touch “Dest” on the map.
2Touch “Enter Destination”.
zThe “Enter Destination” screen can be dis-
played by touching on any of the
“Navigation” screens.
3Touch “Waypoint” on the “Enter Des-
tination” screen.
4Touch the desired method to search
the destination.
zFor detailed information about searching
the destination on the map, see page 33.
XIf you search the destination by “Enter
Address”
5Touch “Add as Waypoint”.
XIf you search the destination by “Select
Point on Map” or Enter Geo-coordi-
nates”
5Touch “Add”.
XIf you search the destination by the other
methods
5Touch the desired entry.
6Touch “Insert Waypoint” to select the
position of the waypoint.
7The route will be recalculated.
ADDING DESTINATIONS
Destinations can be added and the
route changed accordingly.
INFORMATION
In addition to the main destination, a
maximum of 4 waypoints can be set.
The main destination is marked by ,
the waypoints are marked by .
50
3. ROUTE GUIDANCE
1Touch “Show Destination List” on
the “Waypoint” screen.
2Touch the desired destination to be ed-
ited.
3Touch desired item.
zOn this screen, the following functions can
be operated.
EDITING DESTINATIONS
No. Function
Touch to register the point in the
“Stored” list on the “My Destina-
tions” screen. (See page 55.)
Touch to change the order of the
destinations. Touch or to
move the destination up or down the
order displayed on the next screen.
Touch to delete the destination.
Touch to delete all waypoints.
INFORMATION
If the main destination is deleted, the
last waypoint before the deleted destina-
tion will become the new main destina-
tion.
51
3. ROUTE GUIDANCE
2
APPLICATION-“Map”
1Display the route list. (See page 47.)
2Touch the desired segment to detour.
3Touch “Detour”.
or : Touch to display the next or
previous segment.
4The route will be recalculated.
1Display the route list. (See page 47.)
2Touch “Detours”.
3Touch “Detour Off”.
zIf there is more than one point to detour, a
list of points to detour will be displayed.
Select points from the list to cancel
detouring them.
4The route will be recalculated.
DETOURING A SEGMENT ON
THE ROUTE
When detouring a segment, the detour
route can be changed.
DETOURING THE SEGMENT
CANCELLING THE DETOURED
SEGMENT
52
4. MY DESTINATIONS
1. REGISTERING A ENTRY
1Touch “Dest” on the map.
2Touch “My Destinations.
zThe “My Destinations” screen can be dis-
played by touching on any of the
“Navigation” screens.
3Touch “Stored on the “My Destina-
tions” screen.
4Touch “Create New Entry”.
5Input the entry address. (See page 35.)
6Touch “Save New Entry”.
7Input the entry name.
8Touch “OK”.
9The entry is saved in the “Stored” list.
REGISTERING A NEW ENTRY
Up to 200 destinations can be regis-
tered with this system.
INFORMATION
This function cannot be operated while
driving.
REGISTERING FROM THE “My
Destinations” SCREEN
zTouch to display and edit the entry
information. (See page 58.)
53
4. MY DESTINATIONS
2
APPLICATION-“Map”
REGISTERING “Home
1Touch “Home”.
2Touch “Yes”.
3Touch the desired method to search
the point.
zFor details about searching the point on
the map, see page 33.
XIf you search the destination by “Enter
Address”
4Touch “Save as Home Address”.
XIf you search the destination by “Select
Point on Map” or Enter Geo-coordi-
nates”
4Touch “Save”.
XIf you search the destination by the other
methods
4Touch the desired entry from the list.
5The entry is registered as “Home” in
the “Stored” list.
If “Home” has not been registered,
touching “Home allows a home ad-
dress to be registered.
zTouch to display and edit the entry
information. (See page 58.)
54
4. MY DESTINATIONS
1Touch the desired point on the map.
2Touch “Save.
3Follow the steps “REGISTERING
FROM THE “My Destinations”
SCREEN” from “STEP 7”. (See page
52.)
1Search the point by “POI”. (See pages
32 and 36.)
2Touch “Save.
3Follow the steps “REGISTERING
FROM THE “My Destinations”
SCREEN” from “STEP 7”. (See page
52.)
REGISTERING FROM THE LIST ON
THE “Previous” OR “Phone Book”
SCREEN
1Search the point by “Previous” or
“Phone Book”. (See pages 34 and 34.)
2Touch next to the desired item.
3Touch “Add to Stored Destinations”.
4Follow the steps “REGISTERING
FROM THE “My Destinations
SCREEN” from “STEP 7”. (See page
52.)
REGISTERING FROM THE MAP
REGISTERING FROM POI
REGISTERING FROM THE LIST
INFORMATION
If the contact includes an address and a
phone number, they will be stored in the
“Stored” list on the “My Destinations”
screen and “Contacts” screen. (See
pages 52 and 165.)
55
4. MY DESTINATIONS
2
APPLICATION-“Map”
REGISTERING FROM THE DESTI-
NATION LIST
1Display the “Show Destination List”
screen. (See page 50.)
2Touch the desired destination.
3Touch “Add to Stored Destinations”.
4Follow the steps “REGISTERING
FROM THE “My Destinations
SCREEN” from “STEP 7”. (See page
52.)
1Search the point by “Enter Geo-coor-
dinates”. (See page 41.)
2Touch “Save”.
3Follow the steps “REGISTERING
FROM THE “My Destinations
SCREEN” from “STEP 7”. (See page
52.)
REGISTERING FROM GEO-
COORDINATES
56
4. MY DESTINATIONS
LOADING ADDRESSES VIA A USB
MEMORY
1Open the cover of the USB/AUX port
and connect a USB memory.
zThe USB/AUX port is located on the
instrument panel, or in the console box or
glove box etc. The location and design are
different depending on the vehicle. For
details, see the Pictorial index of “Owners
Manual”.
2Touch “Dest” on the map.
3Touch “Enter Destination.
zThe “Enter Destination” screen can be dis-
played by touching on any of the
“Navigation” screens.
4Touch “Advanced” on the “Enter Des-
tination” screen.
5Touch “Load Contacts from USB”.
6The following screen will be displayed
while loading the data.
zTo cancel this function, touch “Cancel”.
7The following screen will be displayed
when loading is complete.
8The entry is registered in the “Stored”
list on the “My Destinations” screen
and “Contacts” screen. (See pages 52
and 165.)
REGISTERING FROM AN
EXTERNAL DEVICE
“vCard” formatted data can be trans-
ferred from a USB memory to this sys-
tem. Transferred addresses and
numbers will be stored in the “Stored”
list on the “My Destinations” screen
and “Contacts” screen. (See pages 52
and 165.)
NOTICE
Do not turn off the engine while down-
loading.
57
4. MY DESTINATIONS
2
APPLICATION-“Map”
LOADING ADDRESSES FROM A
PHONE
INFORMATION
If a message similar to the one below is
displayed, delete X item(s) in the
“Stored” list on the “My Destinations”
screen and “Contacts” screen to make
room for the new destination(s). (See
pages 58 and 168.)
Address and number will be stored in
the “Stored” list on the “My Destina-
tions” screen and “Contacts” screen.
(See pages 52 and 165.) For detailed
information about “Load Addresses
from Phone”, see page 91.
58
4. MY DESTINATIONS
2. DISPLAYING AND EDITING THE ENTRY INFORMATION
1Touch next to the desired item on
the “My Destinations” screen.
XThe entry options screen of “Stored” list
XThe entry options screen of “Previous”
list
XThe entry options screen of “Phone
Book” list
zOn this screen, the following functions can
be operated.
DISPLAYING AND EDITING
THE ENTRY INFORMATION
Detailed information of entries in the
list can be displayed or edited.
NO. Function
Touch to display the details of
the entry information. (See page
59.)
Touch to change the entry name.
(See page 59.)
Touch to edit the address. (See
page 59.)
Touch to delete the entry.
Touch to delete all entries.
Touch to register the entry in the
“Stored” list on the “My Destina-
tions” screen and “Contacts”
screen. (See page 54.)
59
4. MY DESTINATIONS
2
APPLICATION-“Map”
1Touch “Show Details” on the entry
options screen.
2This screen will be displayed.
zThe address will be marked on the map.
zThe address and a picture, if available, of
the contact from the system’s phone book
will be displayed.
1Touch “Rename XX” on the entry op-
tions screen.
2Input the new name.
3Touch “OK.
1Touch “Edit Address” on the entry
options screen.
2Input the new address. (See page 35.)
3Touch “Save Changes”.
SHOW DETAILS OF THE
ENTRY
zWhen you touch “Start”, the starting
route guidance screen will be displayed.
CHANGING THE ENTRY NAME
INFORMATION
This function cannot be operated while
driving.
EDITING THE ADDRESS
INFORMATION
This function cannot be operated while
driving.
If an entry that is transferred from a cel-
lular phone is edited, the change will
affect the entry in the “Stored” list on the
“My Destinations” screen and “Contacts”
screen. (See pages 52 and 165.)
60
4. MY DESTINATIONS
3. SENDING STORED CONTACTS TO A USB MEMORY
1Open the cover of the USB/AUX port
and connect a USB memory.
zThe USB/AUX port is located on the
instrument panel, or in the console box or
glove box etc. The location and design are
different depending on the vehicle. For
details, see the Pictorial index of “Owners
Manual”.
2Press the “SETUP” button.
3Touch “General.
4Touch “Send Stored Contacts to
USB”.
5The following screen will be displayed
while sending the data.
zTo cancel this function, touch “Cancel”.
6The following screen will be displayed
when sending data to the USB memory
is complete.
SENDING STORED
CONTACTS TO A USB
MEMORY
The entries stored in the “Stored” list
on the “My Destinations” screen and
“Contacts” screen (See pages 52 and
165.) can be transferred to a USB
memory.
61
2
APPLICATION-“Map”
5. NAVIGATION SETTING
1. MAP SETTINGS
1Touch “Options”.
2Touch “Map Settings”.
3Touch the item to be set.
zOn this screen, the following functions can
be set.
SETTING THE MAP
No. Function
Touch to change the map layout.
(See page 28.)
Touch to set the display of POI
icon categories. (See page 62.)
Touch to change the vehicle
icon. (See page 62.)
Touch to change the screen to
“Day” or “Night”. (See page
63.)
Touch to change the estimated
time between “Arrival Time/Dis-
tance” and “Remaining Time/
Distance” to the destination.
(See page 63.)
Touch to set the display of the
route guidance arrow on or off.
(See page 44.)
Touch to set the display of the
name of the road currently being
travelled on to on or off. (See
page 44.)
Touch to set the display of sign-
posts on or off. (See page 44.)
Touch to set the display of the
lane recommendation on or off.
(See page 44.)
Touch to set the display of the
traffic message icons on or off.
(See page 44.)
INFORMATION
The current setting of each item is dis-
played on its right.
Selected items checkboxes will change
to when the item has been
selected. All selected items will be acti-
vated simultaneously.
62
5. NAVIGATION SETTING
1Touch “POIs on Map” on the “Map
Settings” screen.
2Select the POI categories.
zOn this screen, the following functions can
be operated.
3Touch .
1Touch “Vehicle Iconson the “Map
Settings” screen.
2Touch the desired icon.
3Touch .
POIS ON MAP
POI categories displayed on the map
can be selected.
No. Function
Touch to display all categories.
Touch to hide all icons.
Touch to display the selected
icons.
Touch to select items from other
categories.
VEHICLE ICONS
The vehicle icon can be changed.
63
5. NAVIGATION SETTING
2
APPLICATION-“Map”
1Touch “Day/Night Modeon the “Map
Settings” screen.
2Touch the desired item.
“Automatic”: Touch to change the screen
to day or night mode depending on the po-
sition of the headlight switch.
“Day: Touch to always display the map in
day mode.
“Night”: Touch to always display the map
in night mode.
3Touch .
1Touch “Arrival Information” on the
“Map Settings” screen.
2Touch the desired item.
“Off”: Touch to turn off the estimated time/
distance.
“Arrival Time/Distance”: Touch to dis-
play the arrival time in the upper right area
of the map. The distance to the destination
will also be displayed.
“Remaining Time/Distance”: Touch to
display the remaining time to reach the
destination in the upper right area of the
map. The distance to the destination will
also be displayed.
3Touch .
DAY/NIGHT MODE
The screen can be changed to day
mode or night mode.
ARRIVAL INFORMATION
The estimated time to the destination
can be changed between arrival time/
distance and remaining time/distance.
It can also be turned off.
64
5. NAVIGATION SETTING
2. ROUTE SETTINGS
1Touch “Dest” on the map.
2Touch “Route Options”.
zThe “Route Options” screen can be dis-
played by touching on any of the
“Navigation” screens.
3Touch “Preferences” on the “Route
Options” screen.
4Touch the desired item.
“Route Type”: Touch to select the route
type between “Fast Route”,“Short
Route” and “Ecological Route”.
“Show Route Alternatives”: Touch to
display 3 routes (fastest, shortest and eco-
logical) on the map after a route calcula-
tion.
“Make a Round Trip”: Touch to have the
route automatically calculated back to the
starting point after the set destination has
been reached.
zEntered waypoints will also be considered
on the way back to the starting point.
5Touch .
SETTING THE ROUTE
OPTIONS
SETTING THE ROUTE
CALCULATION
The route preferences for the route cal-
culation can be set.
INFORMATION
“Show Route Alternatives” and
“Make a Round Trip” are not select-
able at the same time.
65
5. NAVIGATION SETTING
2
APPLICATION-“Map”
1Touch “Dest” on the map.
2Touch “Route Options”.
zThe “Route Options” screen can be dis-
played by touching on any of the
“Navigation” screens.
3Touch “Avoid on the “Route Options”
screen.
4Touch the desired item.
“Avoid Freeways: Touch to avoid free-
ways.
“Avoid Toll Roads: Touch to avoid toll
roads.
“Avoid Tunnels”: Touch to avoid tunnels.
“Avoid Ferries”: Touch to avoid ferries.
“Avoid Border Crossings”: Touch to
avoid border crossings.
5Touch .
SETTING THE AVOIDANCE
CRITERIA FOR THE ROUTE
CALCULATION
The avoidance criteria for the route cal-
culation can be set.
66
6. NAVIGATION SYSTEM INFORMATION
1. LIMITATIONS OF THE NAVIGATION SYSTEM
The Global Positioning System (GPS) de-
veloped and operated by the U.S. Depart-
ment of Defense provides an accurate
current vehicle position, normally using 4
or more satellites, and in some case 3 sat-
ellites. The GPS system has a certain level
of inaccuracy. While the navigation system
will compensate for this most of the time,
occasional positioning errors of up to 300
feet (100 m) can and should be expected.
Generally, position errors will be corrected
within a few seconds.
The GPS signal may be physically ob-
structed, leading to inaccurate vehicle po-
sition on the map display. Tunnels, tall
buildings, trucks, or even the placement of
objects on the instrument panel may ob-
struct the GPS signals.
The GPS satellites may not send signals
due to repairs or improvements being
made to them.
Even when the navigation system is re-
ceiving clear GPS signals, the vehicle po-
sition may not be shown accurately or
inappropriate route guidance may occur in
some cases.
zAccurate current vehicle position may not
be shown in the following cases:
When driving on a small angled Y-
shaped road.
When driving on a winding road.
• When driving on a slippery road such as
in sand, gravel, snow, etc.
When driving on a long straight road.
When motorway and surface streets run
in parallel.
After moving by ferry or vehicle carrier.
When a long route is searched during
high speed driving.
When driving without setting the current
position calibration correctly.
After repeating a change of direction by
going forward and backward, or turning
on a turntable in the parking lot.
When leaving a covered parking lot or
parking garage.
When a roof carrier is installed.
When driving with tire chains installed.
When the tires are worn.
After replacing a tire or tires.
When using tires that are smaller or
larger than the factory specifications.
• When the tire pressure in any of the four
tires is not correct.
This navigation system calculates the
current vehicle position using satellite
signals, various vehicle signals, map
data, etc. However, an accurate posi-
tion may not be shown depending on
satellite condition, road configuration,
vehicle condition or other circumstanc-
es.
NOTICE
The installation of window tinting may
obstruct the GPS signals. Most window
tinting contains some metallic content
that will interfere with GPS signal recep-
tion of the antenna. We advise against
the use of window tinting on vehicles
equipped with navigation systems.
67
6. NAVIGATION SYSTEM INFORMATION
2
APPLICATION-“Map”
zInappropriate route guidance may occur in
the following cases:
When turning at an intersection off the
designated route guidance.
• If you set more than one destination but
skip one of them, auto reroute will dis-
play a route returning to the destination
that was skipped.
When turning at an intersection for which
there is no route guidance.
When passing through an intersection
for which there is no route guidance.
During auto reroute, the route guidance
may not be available for the next turn to
the right or left.
It may take a long time to operate auto
reroute during high speed driving. In
auto reroute, a detour route may be
shown.
After auto reroute, the route may not be
changed.
An unnecessary U-turn may be shown or
announced.
A location may have multiple names and
the system will announce one or more.
Some routes may not be searched.
If the route to your destination includes
gravel, unpaved roads or alleys, the
route guidance may not be shown.
Your destination point might be shown
on the opposite side of the street.
When a portion of the route has regula-
tions prohibiting the entry of the vehicle
that vary by time or season or other rea-
sons.
The road and map data stored in the
navigation system may not be complete
or may not be the latest version.
INFORMATION
This navigation system uses tire turning
data and is designed to work with fac-
tory-specified tires for the vehicle.
Installing tires that are larger or smaller
than the originally equipped diameter
may cause inaccurate display of the cur-
rent vehicle position. The tire pressure
also affects the diameter of the tires so
make sure the tire pressure of all four
tires is correct.
68
6. NAVIGATION SYSTEM INFORMATION
2. MAP INFORMATION
END-USER TERMS
The data (“Data”) is provided for your
personal, internal use only and not for
resale. It is protected by copyright, and
is subject to the following terms and
conditions which are agreed to by you,
on the one hand, and Harman
(“Harman”) and its licensors (including
their licensors and suppliers) on the
other hand.
© 2011 NAVTEQ B.V., © Bundesamt
für Eich- und Vermessungswesen, ©
EuroGeographics, source: © IGN 2009
– BD TOPO®, Die Grundlagendaten
wurden mit
Genehmigung der zustaendigen
Behoerden entnommen, Contains
Ordnance Survey data © Crown
copyright and database right 2010
Contains Royal Mail data © Royal Mail
copyright and database right 2010,
Copyright Geomatics Ltd., Copyright ©
2003; Top-Map Ltd., La Banca Dati
Italiana è stata prodotta usando quale
riferimento anche cartografia numerica
ed al tratto prodotta e fornita dalla
Regione Toscana., Copyright © 2000;
Norwegian Mapping Authority, Source:
IgeoE – Portugal, Información
geográfica propiedad del CNIG, Based
upon electronic data Ó National Land
Survey Sweden., Topografische
Grundlage: Ó Bundesamt für
Landestopographie.. All rights
reserved.
TERMS AND CONDITIONS
PLEASE READ THIS END USER
LICENSE AGREEMENT
CAREFULLY BEFORE USING THE
NAVTEQ DATABASE
NOTICE TO THE USER
THIS IS A LICENSE AGREEMENT -
AND NOT AN AGREEMENT FOR
SALE – BETWEEN YOU AND
NAVTEQ B.V. FOR YOUR COPY OF
THE NAVTEQ NAVIGABLE MAP
DATA-BASE, INCLUDING
ASSOCIATED COMPUTER
SOFTWARE, MEDIA AND
EXPLANATORY PRINTED
DOCUMENTATION PUBLISHED BY
NAVTEQ (JOINTLY “THE
DATABASE”). BY USING THE
DATABASE, YOU ACCEPT AND
AGREE TO ALL TERMS AND
CONDITIONS OF THIS END USER
LICENSE AGREEMENT
(“AGREEMENT”). IF YOU DO NOT
AGREE TO THE TERMS OF THIS
AGREEMENT, PROMPTLY RETURN
THE DATABASE, ALONG WITH ALL
OTHER ACCOMPANYING ITEMS,
TO YOUR SUP-PLIER FOR A
REFUND.
OWNERSHIP
The Database and the copyrights and
intellectual property or neighboring
rights therein are owned by NAVTEQ
or its licensors. Ownership of the media
on which the Database is contained is
retained by NAVTEQ and/or your
supplier until after you have paid in full
any amounts due to NAVTEQ and/or
your supplier pursuant to this
Agreement or similar agreement(s)
under which goods are provided to you.
69
6. NAVIGATION SYSTEM INFORMATION
2
APPLICATION-“Map”
LICENSE GRANT
NAVTEQ grants you a non-exclusive
license to use the Database for your
personal use or, if applicable, for use in
your business’ internal operations. This
license does not include the right to
grant sub-licenses.
LIMITATIONS ON USE
The Database is restricted for use in
the specific system for which it was
created. Except to the extent explicitly
permitted by mandatory laws (e.g.
national laws based on the European
Software Directive (91/250) and the
Database Directive (96/9)), you may
not extract or reutilize substantial parts
of the contents of the Database nor
reproduce, copy, modify, adapt,
translate, disassemble, decompile,
reverse engineer any portion of the
Database. If you wish to obtain
interoperability information as meant in
(the national laws based on) the
European Software Directive, you shall
grant NAVTEQ reasonable opportunity
to provide said information on
reasonable terms, including costs, to
be determined by NAVTEQ.
TRANSFER OF LICENSE
You may not transfer the Database to
third parties, except when installed in
the system for which it was created or
when you do not retain any copy of the
Database, and provided that the
transferee agrees to all terms and
conditions of this Agreement and
confirms this in writing to NAVTEQ.
Multi-disc sets may only be transferred
or sold as a complete set as provided
by NAVTEQ and not as subset thereof.
LIMITED WARRANTY
NAVTEQ warrants that, subject to the
warnings set out below, for a period of
12 months after acquisition of your
copy of the Database, it will perform
substantially in accordance with
NAVTEQ’s Criteria for Accuracy and
Completeness existing on the date you
acquired the Database; these criteria
are available from NAVTEQ at your
request. If the Database does not
perform in accordance with this limited
warranty, NAVTEQ will use reasonable
efforts to repair or replace your non-
conforming copy of the Database. If
these efforts do not lead to
performance of the Database in
accordance with the warranties set out
herein, you will have the option to either
receive a reasonable refund of the
price you paid for the Database or to
rescind this Agreement. This shall be
NAVTEQ’s entire liability and your sole
remedy against NAVTEQ. Except as
expressly provided in this section,
NAVTEQ does not warrant nor make
any representations regarding the use
of results of the use of the Database in
terms of its correctness, accuracy,
reliability, or otherwise. NAVTEQ does
not warrant that the Database is or will
be error free. No oral or written
information or advice provided by
NAVTEQ, your supplier or any other
person shall create a warranty or in any
way increase the scope of the limited
warranty described above. The limited
warranty set forth in this Agreement
does not affect or prejudice any
statutory legal rights that you may have
under the legal warranty against
hidden defects.
70
6. NAVIGATION SYSTEM INFORMATION
If you did not acquire the Database
from NAVTEQ directly, you may have
statutory rights against the person from
whom you have acquired the Database
in addition to the rights granted by
NAVTEQ hereunder according to the
law of your jurisdiction. The above
warranty of NAVTEQ shall not affect
such statutory rights and you may
assert such rights in addition to the
warranty rights granted herein.
LIMITATION OF LIABILITY
The price of the Database does not
include any consideration for
assumption of risk of consequential,
indirect or unlimited direct damages
which may arise in connection with
your use of the Database. Accordingly,
in no event shall NAVTEQ be liable for
any consequential or indirect damages,
including without limitation, loss of
revenue, data, or use, incurred by you
or any third party arising out of your use
of the Database, whether in an action in
contract or tort or based on a warranty,
even if NAVTEQ has been advised of
the possibility of such damages. In any
event NAVTEQ’s liability for direct
damages is limited to the price of your
copy of the Database.
THE LIMITED WARRANTY AND
LIMITATION OF LIABILITY, SET
FORTH IN THIS AGREE-MENT, DO
NOT AFFECT OR PREJUDICE YOUR
STATUTORY RIGHTS WHERE YOU
HAVE ACQUIRED THE DATABASE
OTHERWISE THAN IN THE COURSE
OF A BUSINESS.
WARNINGS
The Database may contain inaccurate
or incomplete information due to the
passage of time, changing
circumstances, sources used and the
nature of collecting comprehensive
geographic data, any of which may
lead to incorrect results. The Database
does not include or reflect information
on - inter alia - neighborhood safety;
law enforcement; emergency
assistance; construction work; road or
lane closures; vehicle or speed
restrictions; road slope or grade; bridge
height, weight or other limits; road or
traffic conditions; special events; traffic
congestion; or travel time.
GOVERNING LAW
This Agreement shall be governed by
the laws of the jurisdiction, in which you
reside at the date of acquisition of the
Database. Should you at that moment
reside outside the European Union or
Switzerland, the law of the jurisdiction
within the European Union or
Switzerland where you acquired the
Database shall apply. In all other
cases, or if the jurisdiction where you
acquired the Database cannot be
defined, the laws of the Netherlands
shall apply. The courts competent at
your place of residence at the time you
acquired the Database shall have
jurisdiction over any dispute arising out
of, or relating to this Agreement,
without prejudice to NAVTEQ’ right to
bring claims at your then current place
of residence.
71
6. NAVIGATION SYSTEM INFORMATION
2
APPLICATION-“Map”
72
6. NAVIGATION SYSTEM INFORMATION
3
73
1
2
3
4
5
6
7
8
9
1. QUICK REFERENCE..................... 74
2. PICTURE SLIDESHOW ................. 75
DISPLAYING THE PICTURES.............. 75
PLAYING PICTURE SLIDESHOWS ..... 76
3. EMAIL ............................................ 77
RECEIVING A NEW EMAIL .................. 77
CHECKING “Email ............................... 77
4. CALENDAR ................................... 79
CHECKING CALENDAR ....................... 79
1. ENTUNE SERVICE ....................... 80
BEFORE USING ENTUNE .................... 80
AVAILABILITY OF SERVICE................. 82
INITIALIZING PERSONAL DATA .......... 82
2. OPERATING NAVIGATION
FUNCTION USING ENTUNE
SERVICE ..................................... 83
ONLINE SEARCH.................................. 83
FUEL PRICES ....................................... 85
TRAFFIC MESSAGES........................... 86
LOADING ADDRESSES FROM A
PHONE................................................ 91
3. OPERATING AN APPLICATION
USING ENTUNE SERVICE......... 93
OPERATING AN APPLICATION ........... 93
IF A MESSAGE APPEARS ON THE
SCREEN ............................................. 95
1APPLICATIONS OPERATION 2ENTUNE SERVICE
APPLICATION-THE OTHERS
74
1. APPLICATIONS OPERATION
1. QUICK REFERENCE
X“Applications” menu screen
The navigation application and several other applications can be accessed by
pressing the “APPS button.
When the “APPS” button is pressed, the “Applications” menu screen that was last
displayed is returned to. Touch to display the “Applications” menu screen.
No. Function Page
Press to display a list of applications.
“Map” provides the user with navigation, route calculation, destination
entry (manually or via voice recognition), turn by turn directions, and
real-time traffic.
25
Touch to view pictures stored on a USB memory. 75
Touch to display Emails. 77
Touch to access the connected phone’s calendar, tasks and notes. 79
Touch to access the applications. 83, 85, 93
Touch to close or delete the applications. 93, 94
Touch to shift to the next or previous page.
75
3
APPLICATION-THE OTHERS
1. APPLICATIONS OPERATION
2. PICTURE SLIDESHOW
1Open the cover of the USB/AUX port
and connect a USB memory.
zThe USB/AUX port is located on the
instrument panel, or in the console box or
glove box etc. The location and design are
different depending on the vehicle. For
details, see the Pictorial index of “Owner’s
Manual”.
2Press the “APPS” button to display
the “Applications” menu screen.
zIf the “Applications” menu screen is not
displayed, touch until it is dis-
played.
3Touch “Pictures.
4The slideshow starts automatically.
: Touch to stop the slideshow.
When the vehicle is stopped, pictures
stored on a USB memory can be
viewed.
INFORMATION
Images cannot be viewed while driving.
When the vehicle starts moving while
viewing pictures, a pop-up window will
be displayed and pictures cannot be dis-
played. Touch Previous” to return to
the previous screen.
Available image data format: JPEG,
PNG and BMP
DISPLAYING THE PICTURES
INFORMATION
All readable pictures on the device are
displayed in chronological order. The
slideshow will repeat when it is finished.
The pictures will be changed every few
seconds.
76
1. APPLICATIONS OPERATION
1Touch “Show”.
2Operating switches will be displayed.
“Hide”: Touch to close the slideshow op-
tions.
: Touch to pause the slideshow.
: Touch to play the slideshow
again.
: Touch to display the previous
picture.
: Touch to display the next pic-
ture.
PLAYING PICTURE
SLIDESHOWS
A slideshow can be played, paused,
and desired images can be selected.
INFORMATION
When the slideshow is playing, the
pause and skip screen buttons disap-
pear automatically after a few seconds.
77
3
APPLICATION-THE OTHERS
1. APPLICATIONS OPERATION
3. EMAIL
1Press the “APPS” button to display
the “Applications” menu screen.
zIf the “Applications” menu screen is not
displayed, touch until it is dis-
played.
2Touch “Email”.
zWhen the downloading of an Email has
been completed, the mail list will be dis-
played.
3Touch the desired Email.
Incoming Emails to a connected
Bluetooth® capable phone can be
downloaded. Before using this
application, connect the Bluetooth®
phone with phone profile. (See page
203.)
RECEIVING A NEW EMAIL
When a new Email is received, a pop-up
window is displayed on the screen.
zThis function can be set to “On” or
“Off”. (See page 209.)
CHECKING “Email”
78
1. APPLICATIONS OPERATION
zThe state of Email is shown by the follow-
ing icons.
: Unread mail
: Read mail
: Important mail
4The text of the Email is displayed.
: Touch to have the Email read out.
To cancel this function, touch .
NOTICE
Do not turn off the engine while down-
loading.
INFORMATION
Email cannot be sent.
79
3
APPLICATION-THE OTHERS
1. APPLICATIONS OPERATION
4. CALENDAR
1Press the “APPS” button to display
the “Applications” menu screen.
zIf the “Applications” menu screen is not
displayed, touch until it is dis-
played.
2Touch “Calendar”.
zWhen the downloading of the calendar is
complete, the current day’s calendar
entries will be displayed.
3When a displayed schedule entry is
touched, the entry’s detailed informa-
tion is displayed.
: Touch to display the previous day’s
schedule.
: Touch to display the following day’s
schedule.
: Touch to display the current day’s
tasks.
: Touch to display the notes.
Calendar entries, tasks and notes from
a connected Bluetooth® capable
phone can be downloaded. Before
using this application, connect the
Bluetooth® phone with phone profile.
(See page 203.)
CHECKING CALENDAR
NOTICE
Do not turn off the engine while down-
loading.
INFORMATION
Calendar entries cannot be edited.
80
2. ENTUNE SERVICE
1. ENTUNE SERVICE
1Perform user registration from the des-
ignated web address.
1Touch “enTune Username”.
2Input the username and then touch
“OK”.
3Touch “enTune Password”.
4Input the password and then touch
“OK”.
5Touch “Confirm Login Information”.
zWhen “Remember Password” is on, the
entered user login information will be
remembered for every login.
BEFORE USING ENTUNE
USER REGISTRATION
When purchasing the vehicle, an email
address is registered at your Toyota
dealer. If your email address was not
registered at your Toyota dealer, your
email address can be registered at the
Entune website. A user registration
guidance email containing a web ad-
dress will be sent.
LOGIN PROCESS TO ENTUNE
SERVICE
If the following screen is displayed
when you use the Entune service, en-
ter the login information.
: Entune is available in the 48 states, D.C. and Alaska.
81
2. ENTUNE SERVICE
3
APPLICATION-THE OTHERS
1Download the Entune application using
your cellular phone.
2Run the Entune application on your
cellular phone.
3Enter a user name and password into
the Entune application on your cellular
phone.
REGISTERING THE
DOWNLOADED ENTUNE
APPLICATION
INFORMATION
If your email address was not registered
at your Toyota dealer when the vehicle
was purchased, an email address can
be registered at http://www.toyota.com/
entune/.
Entune operational procedures can also
be confirmed by visiting http://
www.toyota.com/entune/.
This system supports the following ser-
vice.
• Bluetooth® Specification
Ver.1.1 or higher
(Recommended: Ver.2.1 + EDR or
higher)
•Profiles
HFP (Hands Free Profile)
Ver.1.0 or higher
(Recommended: Ver.1.5 or higher)
DUN (Dial-Up Networking Profile)
Ver.1.1 or higher
PAN (Personal Area Network)
Ver. 1.0
PBAP (Phone Book Access Profile)
Ver.1.0 or higher
SSP (Serial Port Profile)
MAP (Message Access Profile)
•Application
PIM (Personal Information Manager)
If your cellular phone does not support
HFP, you cannot register the Bluetooth®
phone, or use DUN/PAN or PBAP pro-
files individually.
If the connected Bluetooth® phone ver-
sion is older than recommended or
incompatible, this function may not be
used.
82
2. ENTUNE SERVICE
zEntune is available in the 48 states,
D.C. and Alaska.
zThe following personal data can be
deleted and returned to their default set-
tings:
Downloaded contents
Radio stations that were listened to
• Input history
AVAILABILITY OF SERVICE
INFORMATION
When using Entune, depending on the
details of your cellular phone contract,
data usage fees may apply. Confirm
data usage fees before using this ser-
vice.
In this section, the required operations
to activate application, connect a cellular
phone to the navigation system and reg-
istration steps for Entune are explained.
For details regarding Entune operations
and each of the application, refer to
http://www.toyota.com/entune/.
INITIALIZING PERSONAL
DATA
The personal data used in application
can be reset. (See “DELETE PER-
SONAL DATA” on page 199.)
INFORMATION
Once initialized, data will be erased. Pay
close attention when initializing the data.
83
3
APPLICATION-THE OTHERS
2. ENTUNE SERVICE
2. OPERATING NAVIGATION FUNCTION USING ENTUNE SERVICE
1Touch “Dest” on the map.
2Touch “Enter Destination”.
zThe “Enter Destination” screen can be dis-
played by touching on any of the
“Navigation” screens.
3Touch “POI” on the “Enter Destina-
tion” screen.
4Touch “Online Search by Xxxx”.
zOnline search can be entered on the
“Applications” menu screen.
zWhen the following screen is displayed,
enter the user login information and then
touch “Confirm Login Information”.
(See page 80.)
zWhen the cost warning or roaming warn-
ing screen is displayed, touch “Con-
tinue. This function can be set to on or
off. (See page 208.)
5Touch Search Area.
6Select the desired search area.
“At Current Position”: Touch to define
the area at the current position.
“Define City”: Touch to define the area by
city name. Input the city name and then
touch “OK”.
“From Map”: Touch to define the area on
map. Touch the desired city on the map
and then touch “Select”.
“At Destination”: Touch to define the
area around the main destination. When
route guidance is not in use, “At Destina-
tion” cannot be selected.
ONLINE SEARCH
A destination can be selected via on-
line search.
Before using this function, connect a
Bluetooth® phone with an internet pro-
file. (See page 203.)
84
2. ENTUNE SERVICE
7Touch “Enter Search Word”.
8Input the search word and then touch
“OK”.
9The search results will be displayed.
Touch the desired item.
zUp to 20 items will be searched when per-
forming an online search.
“Download More”: Touch to search up to
20 new items. Up to 60 items can be down-
loaded.
“Previous Results”: Touch to display the
previous result.
“Next Results”: Touch to display the next
result.
10Touch “Calculate”.
“Details”: Touch to display the details of
the point information.
: Touch to call the registered tele-
phone number.
11The starting route guidance screen will
be displayed. (See page 42.)
INFORMATION
The color of indicates if online con-
nection is active or not. After a timeout
of 1 minute, an active online connection
will automatically be terminated.
85
2. ENTUNE SERVICE
3
APPLICATION-THE OTHERS
1Touch “Dest” on the map.
2Touch “Enter Destination”.
zThe “Enter Destination” screen can be dis-
played by touching on any of the
“Navigation” screens.
3Touch “POI” on the “Enter Destina-
tion” screen.
4Touch “Fuel Prices” on the “POI”
screen.
zWhen the login information screen is dis-
played, enter the user login information
and then touch “Confirm Login Informa-
tion”. (See page 80.)
zWhen the cost warning or roaming warn-
ing screen is displayed, touch “Con-
tinue”. This function can be set to on or
off. (See page 208.)
5Touch for the desired item.
zOn this screen, the following functions can
be operated.
zIf you touch the desired item, the starting
route guidance screen will be displayed
directly. (See page 42.)
6Touch “Calculate”.
7The starting route guidance screen will
be displayed. (See page 42.)
FUEL PRICES
It enables the navigation system to dis-
play current fuel prices and gas station
locations, which can be set as a desti-
nation if desired.
Before using this function, connect a
Bluetooth® phone with an internet pro-
file. (See page 203.)
No. Function
Touch to display search result list
sorted by company brand.
Touch to display search result list
sorted by the price.
Touch to display search result list
sorted by the distance.
Touch to select the desired fuel
type.
zWhen “Save” is touched, the point is
registered in the “Stored” list on the “My
Destinations” screen. (See page 54.)
zWhen is touched, the registered
telephone number is called.
86
2. ENTUNE SERVICE
1Touch “Dest” on the map.
2Touch “Traffic Messages”.
zThe “Traffic Messages” screen can be dis-
played by touching on any of the
“Navigation” screens or “Traffic” on the
“Applications” menu screen.
zWhen the login information screen is dis-
played, enter the user login information
and then touch “Confirm Login Informa-
tion”. (See page 80.)
zWhen the cost warning or roaming warn-
ing screen is displayed, touch “Con-
tinue”. This function can be set to on or
off. (See page 208.)
3Touch “On Route,“Show All” or
“Warnings” to select the desired list.
“On Route”: During route guidance, the
traffic messages relating to the set route
will be displayed.
“Show All”: All traffic messages will be
displayed.
“Warnings”: Traffic messages with warn-
ings will be displayed.
4Touch the desired message.
TRAFFIC MESSAGES
It contains a list of traffic messages re-
lating to the set route, all traffic mes-
sages and warnings.
Before using this function, connect a
Bluetooth® phone with an internet pro-
file. (See page 203.)
DISPLAYING TRAFFIC
MESSAGES
87
2. ENTUNE SERVICE
3
APPLICATION-THE OTHERS
zOn this screen, the following information is
displayed.
5The traffic message will be displayed.
or : Touch to display next or pre-
vious traffic message.
: Touch to have the traffic message
read out. To cancel this function, touch
.
“More”: Touch to display all messages.
LIST OF TRAFFIC MESSAGE
ICONS
No. Information
Street number
Route segment
If route segment is not available,
information such as street name,
city name, region or country will
be displayed.
: Icon of an incident
: Icon of an incident on the
route
: Icon of an incident on the
detoured route
Distance to incident
Icon Name
Slippery
Bad weather
Wind
Snow fall
Traffic
Heavy traffic
Accident
Road construction
Narrow track
Warning
Blockage
Security checkpoint
Information
88
2. ENTUNE SERVICE
DETOURING THE SEGMENT
1Displaying the traffic information list.
(See page 86.)
2Touch “On Route” on the “Traffic
Messages” screen.
3Touch the desired segment to detour.
4Touch “Detour”.
or : Touch to display the next or
previous message.
: Touch to have the traffic message
read out. To cancel this function, touch
.
“More: Touch to display all traffic mes-
sages.
5The route will be recalculated.
zThe mark of the TMC on the “On Route”
screen changes into .
CANCELLING THE DETOURED
SEGMENT
1Touch the detoured segment on the
“On Route” screen.
2Touch “Detour Off”.
or : Touch to display the next or
previous message.
: Touch to have the traffic message
read out. To cancel this function, touch
.
“More”: Touch to display all traffic mes-
sages.
3The route will be recalculated.
zThe mark of the TMC on the “On Route”
screen changes to .
DETOURING A SEGMENT
FROM A TRAFFIC MESSAGE
LIST
If a traffic message relates to the route
being travelled, the desired segment
can be detoured.
89
2. ENTUNE SERVICE
3
APPLICATION-THE OTHERS
IF “Automatic” IS SELECTED
1The following screen will be displayed.
2The route will be recalculated automat-
ically.
IF “Manual” IS SELECTED
1The following screen will be displayed.
“Consider”: Touch to display with the cur-
rent route, the TMC event and the sug-
gested detour.
“Ignore”: Touch to ignore the message.
XIf “Consider” is selected
2Touch “Ignore” or “Detour”.
“Ignore”: Touch to ignore the message.
“Detour”: Touch to recalculate the route.
RECALCULATING THE ROUTE
BY THE TRAFFIC MESSAGES
You will be informed about relevant
traffic messages on the route by a pop-
up window.
A pop-up window may differ depending
on the traffic message settings. (See
page 91.)
90
2. ENTUNE SERVICE
1Touch “Dest” on the map.
2Touch “Route Options”.
zThe “Route Options” screen can be dis-
played by touching on any of the
“Navigation” screens.
3Touch “Settings”.
zPlease refer to the following pages for a
description of each setting.
SETTING “Radius Filter”
1Touch “Radius Filter” on the “Set-
tings” screen.
2Touch desired item.
“Off”: Touch to deactivate the function.
“6 mi” ~ “60 mi”: Touch to set the radius
from 6 miles to 60 miles.
3Touch .
TRAFFIC MESSAGE SETTINGS
Once the radius filter has been set,
only traffic messages within the radius
will be displayed in the traffic message
list.
91
2. ENTUNE SERVICE
3
APPLICATION-THE OTHERS
SETTING “Dynamic Reroute”
1Touch Dynamic Reroute” on the
“Settings” screen.
2Touch the desired item.
“Off”: Touch to disable receiving traffic
messages and no reroute will be calculat-
ed.
“Automatic”: Touch to enable relevant
traffic messages on the route to be dis-
played as a pop-up window and activate
automatic reroute calculation.
“Manual”: Touch to enable relevant traffic
messages on the route to be displayed as
a pop-up window but disable automatic re-
route calculation. The user decides if re-
route calculation is desirable or not.
3Touch .
1Touch “Dest” on the map.
2Touch “Enter Destination”.
zThe “Enter Destination” screen can be dis-
played by touching on any of the
“Navigation” screens.
3Touch “Advanced” on the “Enter Des-
tination” screen.
4Touch “Load Addresses from
Phone”
zWhen the login information screen is dis-
played, enter the user login information
and then touch “Confirm Login Informa-
tion”. (See page 80.)
The method of reroute can be set.
LOADING ADDRESSES
FROM A PHONE
Addresses and numbers will be stored
in the “Stored” list on the “My Destina-
tions” screen and “Contacts” screen.
(See pages 52 and 165.)
92
2. ENTUNE SERVICE
zWhen the cost warning or roaming warn-
ing screen is displayed, touch “Con-
tinue”. This function can be set to on or
off. (See page 208.)
5The following screen will be displayed
when loading is complete.
6The entry is registered in the “Stored”
list on the “My Destinations” screen
and “Contacts” screen. (See pages 52
and 165.)
NOTICE
Do not turn off the engine while down-
loading.
INFORMATION
If a message similar to the one below is
displayed, delete X item(s) in the
“Stored” list on the “My Destinations”
screen and “Contacts” screen to make
room for the new destination(s). (See
pages 58 and 168.)
93
3
APPLICATION-THE OTHERS
2. ENTUNE SERVICE
3. OPERATING AN APPLICATION USING ENTUNE SERVICE
OPENING AN APPLICATION
1Press the “APPS” button to display
the “Applications” menu screen.
zIf the “Applications” menu screen is not
displayed, touch until it is dis-
played.
2Touch the desired application.
zWhen the login information screen is dis-
played, enter the user login information
and then touch “Confirm Login Informa-
tion”. (See page 80.)
zWhen the cost warning or roaming warn-
ing screen is displayed, touch “Con-
tinue. This function can be set to on or
off. (See page 208.)
zSeveral downloaded applications can be
opened at the same time and the desired
application can be selected.
z is displayed on the left side of applica-
tion names that are currently open.
3The application is opened.
(on some applications): Touch to up-
date the data
CLOSING AN APPLICATION
1Touch .
2Touch “Close” on the right side of the
application to be closed.
OPERATING AN
APPLICATION
Before using applications, connect the
Bluetooth® phone with an internet
profile. (See page 203.) If a Bluetooth®
connection with an internet profile is
not currently active, applications will be
dimmed.
OPENING/CLOSING AN
APPLICATION
94
2. ENTUNE SERVICE
1Touch .
2Touch “Delete” on the right side of the
application to be deleted.
zApplications that displayed “Delete” on the
right side of the application can be
removed.
3The following confirmation screen will
be displayed. Touch “Yes”.
DELETING AN APPLICATION
95
2. ENTUNE SERVICE
3
APPLICATION-THE OTHERS
: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
IF A MESSAGE APPEARS ON THE SCREEN
When problems occur starting up the application player, a message will appear on
the screen. Referring to the table below to identify the problem, take the suggested
corrective action.
Message Display conditions Corrective action
“This feature is unavailable
while transferring contacts.”
Contacts are being trans-
ferred manually from the
phone book.
When the transfer of contacts
is complete, perform the op-
eration.
“There is a problem with the
Bluetooth connection.
For troubleshooting
assistance, please visit
toyota.com or call 1-800-331-
4331.”
The cellular phone cannot be
connected.
Refer to http://
www.toyota.com/entune/ to
confirm if the phone is
compatible or not.
“This feature is unavailable
during a handsfree call.”
A hands-free call is in
progress.
After the hands-free call is fin-
ished, perform the operation.
To use the services, an active
application needs to be run-
ning on your phone. For more
information, please visit
toyota.com.
The Entune application can-
not be connected to SSP.
Refer to http://
www.toyota.com/entune/ to
confirm if the phone is SSP
compatible or not, and then
activate the Entune applica-
tion.
Apps connection was
dropped.
Please check your phone.
Communication was discon-
nected.
After a few moments, retry
the operation.
96
2. ENTUNE SERVICE
97
2. ENTUNE SERVICE
3
APPLICATION-THE OTHERS
98
1. QUICK REFERENCE .................. 100
2. SOME BASICS............................ 102
TURNING THE AUDIO SYSTEM
ON OR OFF....................................... 102
CONTROLS USING THE
“TUNE SCROLL” KNOB.................... 103
SWITCHING AUDIO SOURCE............ 103
DSP CONTROL ................................... 104
TONE AND BALANCE......................... 105
3. RADIO OPERATION ................... 106
SWITCHING TO RADIO MODE........... 106
PRESETTING A STATION .................. 106
SELECTING A STATION..................... 107
RADIO BROADCAST DATA
SYSTEM ............................................ 107
TRAFFIC ANNOUNCEMENT .............. 108
USING HD Radio™ TECHNOLOGY.... 109
1AUDIO SYSTEM OPERATION
4
99
1
2
3
4
5
6
7
8
9
4. RADIO OPERATION
(XM® Satellite Radio
BROADCAST) ........................... 112
HOW TO SUBSCRIBE TO AN
XM® Satellite Radio .......................... 112
DISPLAYING THE RADIO ID.............. 112
SWITCHING TO SATELLITE RADIO
MODE ............................................... 113
CHANNEL CATEGORY ...................... 113
PRESETTING A CHANNEL ................ 113
SELECTING A CHANNEL................... 114
DISPLAYING THE TITLE
AND NAME ....................................... 114
IF THE SATELLITE RADIO TUNER
MALFUNCTIONS.............................. 115
5. CD PLAYER OPERATION .......... 117
INSERTING OR EJECTING A DISC... 117
SWITCHING TO CD MODE ................ 118
PLAYING AN AUDIO CD .................... 118
PLAYING A MP3/WMA DISC.............. 120
6. USB MEMORY/iPod
OPERATION.............................. 123
CONNECTING A USB
MEMORY OR iPod ........................... 123
SWITCHING TO
USB OR iPod MODE ........................ 124
PLAYING A USB
MEMORY OR iPod ........................... 124
7. AUX DEVICE OPERATION......... 130
CONNECTING A PORTABLE
AUDIO DEVICE................................. 130
SWITCHING TO AUX MODE .............. 131
PLAYING A PORTABLE
AUDIO DEVICE................................. 131
8. Bluetooth® AUDIO
OPERATION ............................. 132
SWITCHING TO Bluetooth®
AUDIO MODE ................................... 133
CONNECTING Bluetooth® AUDIO ...... 134
PLAYING Bluetooth® AUDIO............... 137
9. STEERING SWITCHES............... 141
STEERING SWITCHES
(WITH TWO DIRECTION
STEERING SWITCH)........................ 141
STEERING SWITCHES
(WITH FOUR DIRECTION
STEERING SWITCH)........................ 142
10. AUDIO SYSTEM
OPERATING HINTS.................. 144
RADIO RECEPTION............................ 144
iPod...................................................... 145
USB MEMORY .................................... 146
CARING FOR YOUR CD PLAYER
AND DISCS....................................... 146
MP3/WMA FILES................................. 148
CD-R AND CD-RW DISCS .................. 149
TERMS ................................................ 150
Gracenote®.......................................... 151
AUDIO SYSTEM
100
1. AUDIO SYSTEM OPERATION
1. QUICK REFERENCE
zThe actual design and button position may differ depending on the vehicle. For
details, see Section 3 of “Owner’s Manual”.
To access the audio system, press the “AUDIO” button. The audio system turns
on in the last mode used.
No. Name Function Page
Audio control
screen
A selected audio source is displayed, and it can
be operated with the touch screen controls.
Disc slot Insert a disc into this slot. The CD player turns on
immediately. 117
“Source” Touch to select your desired audio sources. The
audio source selection screen will be displayed. 103
“TUNE SCROLL”
knob
Turn to select radio station bands, tracks and
files. Also, the knob can be used for selection
from the list display.
103
“AUDIO” button Press to display the audio control screen. The au-
dio system turns on in the last mode used. 102103
button* Press to pause or resume playing the music.
101
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
*: If equipped
“SEEK/TRACK
button
Press the “ ” or “ ” button to seek up or down for
a station, or to access a desired track or file.
107, 114,
119, 121,
124, 137
“PWR VOL” knob Press to turn the audio system on and off, and
turn to adjust the volume. 102
button Press to eject a disc. 117
No. Name Function Page
102
1. AUDIO SYSTEM OPERATION
2. SOME BASICS
“AUDIO” button: Press this button to dis-
play screen buttons for the audio system.
“PWR VOL” knob: Press this knob to turn
the audio system on and off. Turn this
knob to adjust the volume. The system
turns on in the last mode used.
This section describes some of the ba-
sic features of the audio system. Some
information may not pertain to your
system.
Your audio system works when the en-
gine switch is turned to the “ACC” or
“ON” position.
CAUTION
For vehicles sold in U.S.A. and Canada:
Part 15 of the FCC Rules
FCC Warning: Changes or modifications
in construction not expressly approved
by the party responsible for compliance
could void the user’s authority to operate
the equipment. Radio frequency expo-
sure. This device is approved for Mobile
Application only and, to comply with
applicable FCC radio frequency expo-
sure regulations, must be used with a
distance of at least 7.9 in. (20 cm)
between the antenna and the body of
any person at all time during use.
Laser products
Do not take this unit apart or attempt to
make any changes yourself. This is an
intricate unit that uses a laser pickup to
retrieve information from the surface of
compact discs. The laser is carefully
shielded so that its rays remain inside
the cabinet. Therefore, never try to dis-
assemble the player or alter any of its
parts since you may be exposed to
laser rays and dangerous voltages.
This product utilizes a laser. Use of
controls or adjustments or perfor-
mance of procedures other than those
specified herein may result in hazard-
ous radiation exposure.
NOTICE
To prevent the 12-volt battery from being
discharged, do not leave the audio sys-
tem on longer than necessary when the
engine is not running.
TURNING THE AUDIO
SYSTEM ON OR OFF
INFORMATION
If the volume is adjusted while music is
paused or muted, the pause or mute will
be cancelled.
103
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
XRadio mode
Radio stations can be tuned in manually
using this knob.
XModes other than radio
Tracks, songs or files can be selected us-
ing the knob.
XWhen a list displayed
When a list is displayed on the screen, turn
the “TUNE SCROLL” knob to move the
cursor box to select a desired item from
the list, and pressing the knob will play it.
The track that is being played is highlight-
ed.
1Press the “AUDIO” button.
zThe audio system turns on in the last
mode used.
2Touch “Source” on the screen.
3Touch a desired audio source.
CONTROLS USING THE
“TUNE SCROLL” KNOB
SWITCHING AUDIO SOURCE
INFORMATION
You cannot select dimmed screen but-
tons. Connect the audio device before
selecting.
104
1. AUDIO SYSTEM OPERATION
1Press the “AUDIO” button.
2Touch or .
XUSB memory/iPod and Bluetooth® au-
dio modes
XModes other than USB memory/iPod
and Bluetooth® audio
3Touch the “DSP” tab to display this
screen.
XWithout JBL sound system
XWith JBL sound system
4Touch the desired screen button.
XWithout JBL sound system
1Touch “On” of “Automatic Sound
Levelizer”.
2Touch “OK”.
XWith JBL sound system
1Touch “High”,“Mid” or “Low” of
“Automatic Sound Levelizer”.
2Touch “OK”.
1Touch “On” of “Surround”.
2Touch “OK”.
DSP CONTROL
zDSP control can be set from the
“Options” screen. Touch “Options” and
then touch “Sound Settings” on the
next screen.
AUTOMATIC SOUND
LEVELIZER (ASL)
The system adjusts to the optimum vol-
ume and tone quality according to ve-
hicle speed to compensate for
increased vehicle noise.
SURROUND FUNCTION
(IF EQUIPPED)
105
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
1Press the “AUDIO” button.
2Touch or .
XUSB memory/iPod and Bluetooth® au-
dio modes
XModes other than USB memory/iPod
and Bluetooth® audio
3Touch the Sound” tab to display this
screen.
4Touch the desired screen button.
“Treble” “+” or “-: To adjust high-
pitched tones.
“Mid” “+” or “-”: To adjust mid-pitched
tones.
“Bass” “+” or “-”: To adjust low-pitched
tones.
“Front” or “Rear”: To adjust the sound
balance between the front and rear speak-
ers.
“L” or “R”: To adjust the sound balance
between the left and right speakers.
5Touch “OK”.
TONE AND BALANCE
TONE
How good an audio program sounds is
largely determined by the mix of the
treble, mid and bass levels. In fact, dif-
ferent kinds of music and vocal pro-
grams usually sound better with
different mixes of treble, mid and bass.
BALANCE
A good balance of the left and right ste-
reo channels and of the front and rear
sound levels is also important.
Keep in mind that when listening to a
stereo recording or broadcast, chang-
ing the right/left balance will increase
the volume of one group of sounds
while decreasing the volume of anoth-
er.
zTone and balance can be set from the
“Options” screen. Touch “Options” and
then touch “Sound Settings” on the
next screen.
INFORMATION
The tone of each mode can be adjusted.
106
1. AUDIO SYSTEM OPERATION
3. RADIO OPERATION
1Press the “AUDIO” button.
zThe audio system turns on in the last
mode used.
2Touch “Source on the screen.
3Touch “AM” or “FM” on the screen.
1Tune in the desired station.
2Touch one of the left side screen but-
tons (1-6) and hold it until a beep is
heard. This sets the frequency to the
screen button. The station’s frequency
will be displayed in the screen button.
zTo change the preset station to a different
one, follow the same procedure.
zTouch or to change the preset
page.
SWITCHING TO RADIO MODE PRESETTING A STATION
Radio mode has a mix preset function,
which can store up to 36 stations (6
station per page u 6 page) from any of
the AM, FM or SAT bands.
107
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
Preset tuning: Touch one of the mix pre-
set channels on the left side of the screen
to select the desired station. The screen
button is highlighted and the station fre-
quency appears on the screen.
Manual tuning: Search for a desired radio
station by turning the “TUNE SCROLL”
knob.
Seek tuning: Press the “ ” or “ ” button
of “SEEK/TRACK”. The radio will begin
seeking up or down for a station of the
nearest frequency and will stop when a
station is found. Each time the button is
pressed, the stations will be searched au-
tomatically one after another.
To scan all the frequencies: Touch
“SCAN”. “SCAN” will appear on the
screen. The radio will find the next station
and stay there for 10 seconds if “All” or
“HD Only” is selected, or 5 seconds if
“Analog” is selected, and then scan
again. To stay tuned to a station and stop
the scanning, touch “SCAN” again. (To
set the HD Radio™ system, see page
210.)
1Touch “Options”.
SELECTING A STATION
Tune in the desired station using one of
the following methods.
RADIO BROADCAST DATA
SYSTEM
This audio system is equipped with Ra-
dio Broadcast Data Systems (RBDS).
RBDS mode allows text messages to
be received from radio stations that uti-
lize RBDS transmitters.
When RBDS is on, the radio can
— only select stations of a particular
program type,
— display messages from radio sta-
tions,
— search for a stronger signal station.
RBDS features are available only
when listening to an FM station that
broadcasts RBDS information and the
“FM info” indicator is on.
SELECTING A DESIRED TYPE
108
1. AUDIO SYSTEM OPERATION
2Touch TYPE >” or “< TYPE” to move
forward and backward through the pro-
gram list.
zOnce a program type has been set,
“TYPE SEEK” will appear on the screen.
zThe program list is in the following order:
• Classical
• Country
• EasyLis (Easy Listening)
Inform (Information)
•Jazz
•News
• Oldies
• Other
Pop Music
• Religion
•Rock
R&B (Rhythm and Blues)
• Sports
•Talk
Traffic (Not available when “HD Radio™
Settings” are set to analog)
Alert (Emergency Alert)
3Touch “TYPE SEEK” and the system
will start to seek for stations in the rele-
vant program type.
“Traffic”: Touch to seek a traffic program
station. “TRAF SEEK” will appear on the
screen.
INFORMATION
If no relevant program can be found, “no
type” will appear on the screen.
TRAFFIC ANNOUNCEMENT
A station that regularly broadcasts traf-
fic information is automatically located.
INFORMATION
If no traffic program station is found, “No
Traffic” will appear on the screen.
If a traffic program station is found, the
name of the traffic program station will
be displayed for a while.
109
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
1Touch “HD Radio” to turn the indicator
on.
zAs a user works through the analog radio
stations, (where applicable) the radio
receiver will automatically tune from an
analog signal to a digital signal within 5
seconds.
zAn orange “HD)” logo indicator will be dis-
played on the screen when in digital. The
“HD)” logo will first appear in a gray color
indicating the station is indeed (an analog
and) a digital station. Once the digital sig-
nal is acquired, the logo will change to a
bright orange color.
1Touch “Text”.
2Information such as the artist name,
song title, album title and music genre
being listened to are displayed on the
text screen.
zTo display messages from the station,
touch “Additional information”.
1Touch “Multicast”.
zEach time “Multicast” is touched, the
supplemental program changes.
zIf Multicast” is touched when tuned to
the last of the supplemental programs, the
main program will be returned to.
USING HD Radio™
TECHNOLOGY
HD Radio™ Technology is the digital
evolution of analog AM/FM radio. Your
radio product has a special receiver
which allows it to receive digital
broadcasts (where available) in
addition to the analog broadcasts it
already receives. Digital broadcasts
have better sound quality than analog
broadcasts as digital broadcasts
provide free, crystal clear audio with no
information, and a guide to available
radio stations and programming, refer
to www.hdradio.com.
INFORMATION
MULTICAST
On the FM radio frequency most digital
stations have “multiple” or supplemen-
tal programs on the FM station.
110
1. AUDIO SYSTEM OPERATION
1Touch “Tag” to bookmark the music
information.
2Open the cover and connect iPod us-
ing an iPod cable.
zThe USB/AUX port is located on the
instrument panel, or in the console box or
glove box etc. The location and design are
different depending on the vehicle. For
details, see the Pictorial index of “Owners
Manual”.
zTurn on the power of the iPod if it is not
turned on.
zOnce an iPod is connected, the music tag
moves from the radio into the iPod.
zWhen the iPod is connected to iTunes, the
“tagged” information of the songs which
were tagged while listening to the radio
can be viewed. Then a user may decide to
purchase the song or CD/Album which
has been listened to on their radio.
TAG INFORMATION
If tagging the music information fails,
“Saving the HD Radio tag failed.” will be
displayed on the screen. If this occurs,
tag the information again.
HD Radio™ stations can be preset.
111
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
TROUBLESHOOTING GUIDE
Experience Cause Action
Mismatch of time alignment
a users may hear a short
period of programming re-
played or an echo, stutter
or skip.
The radio stations analog
and digital volume is not
properly aligned or the sta-
tion is in ballgame mode.
None, radio broadcast issue. A
user can contact the radio station.
Sound fades, blending in
and out.
Radio is shifting between
analog and digital audio.
Reception issue, may clear-up as
the vehicle continues to be driven.
Touching “HD Radio” with the in-
dicator off can force radio in an an-
alog audio.
Audio mute condition when
an HD2/HD3 multicast
channel has been playing.
The radio does not have
access to digital signals at
the moment.
This is normal behavior, wait until
the digital signal returns. If out of
the coverage area, seek a new
station.
Audio mute delay when se-
lecting an HD2/HD3 multi-
cast channel preset.
The digital multicast con-
tent is not available until
HD Radio™ broadcast can
be decoded and make the
audio available. This takes
up to 7 seconds.
This is normal behavior, wait for
the audio to become available.
Text information does not
match the present song au-
dio.
Data service issue by the
radio broadcaster.
Broadcaster should be notified.
Complete the form;
www.ibiquity.com/automotive/
report_radio_station_experiences.
No text information shown
for the present selected fre-
quency.
Data service issue by the
radio broadcaster.
Broadcaster should be notified.
Complete the form;
www.ibiquity.com/automotive/
report_radio_station_experiences.
HD Radio Technology manufactured under license from iBiquity Digital Corpora-
tion. U.S. and Foreign Patents. HD Radio™ and the HD, HD Radio, and “Arc” logos
are proprietary trademarks of iBiquity Digital Corp.
112
1. AUDIO SYSTEM OPERATION
4. RADIO OPERATION (XM
®
Satellite Radio BROADCAST)
zIf “CH 000” is selected using the
“TUNE SCROLLknob, the ID code,
which is 8 alphanumeric characters, will
be displayed. If another channel is
selected, the ID code will no longer be
displayed. The channel (000) displays
the radio ID and the specific radio code.
HOW TO SUBSCRIBE TO AN
XM® Satellite Radio
To listen to a satellite radio broadcast
in the vehicle, a subscription to the
XM® Satellite Radio service is neces-
sary.
An XM® Satellite Radio is a tuner de-
signed exclusively to receive broad-
casts provided under a separate
subscription. Availability is limited to
the 48 contiguous U.S. states and
some Canadian provinces.
HOW TO SUBSCRIBE
It is necessary to enter into a separate
service agreement with XM® Satellite
Radio in order to receive satellite
broadcast programming in the vehicle.
Additional activation and service sub-
scription fees apply that are not includ-
ed in the purchase price of the vehicle
and digital satellite tuner.
zFor complete information on subscrip-
tion rates and terms, or to subscribe to
XM® Satellite Radio:
XU.S.A.
Refer to www.siriusxm.com or call 1-
800-967-2346.
XCanada
Refer to www.xmradio.ca or call 1-
877-209-0079.
INFORMATION
XM® Satellite Radio is solely responsi-
ble for the quality, availability and con-
tent of the satellite radio services
provided, which are subject to the terms
and conditions of the XM® Satellite
Radio customer service agreement.
Customers should have their radio ID
ready; the radio ID can be found by tun-
ing to “channel 000” on the radio. For
details, see “DISPLAYING THE RADIO
ID” below.
All fees and programming are the
responsibility of XM® Satellite Radio and
are subject to change.
SATELLITE TUNER
TECHNOLOGY NOTICE
Toyota’s satellite radio tuners are
awarded Type Approval Certificates
from XM® Satellite Radio Inc. as proof
of compatibility with the services of-
fered by XM® Satellite Radio.
DISPLAYING THE RADIO ID
Each XM® tuner is identified with a
unique radio ID. The radio ID is re-
quired when activating an XM® service
or when reporting a problem.
113
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
1Press the “AUDIO” button to display
the audio control screen.
zThe audio system turns on in the last
mode used.
2Touch “Source” on the screen.
3Touch “SAT on the screen.
1Touch “Options”.
2Touch either “TYPE >” or “< TYPE” to
go to the next or previous category.
1Tune in the desired channel.
2Touch one of the left side screen but-
tons (1-6) and hold it until a beep is
heard. This sets the preset frequency
to the screen button. The Channel
number will be displayed in the screen
button.
zTo change the preset channel to a differ-
ent one, follow the same procedure.
SWITCHING TO SATELLITE
RADIO MODE
CHANNEL CATEGORY
PRESETTING A CHANNEL
114
1. AUDIO SYSTEM OPERATION
Preset tuning: Touch the channel selector
screen button (1-6) to listen to the desired
channel. The selected screen button (1-6)
is highlighted and its related information
appears on the right side of the screen.
Manual tuning: Turn the “TUNE SCROLL”
knob to select the next or previous channel.
Turning the knob quickly allows rapid scroll-
ing through the channel list.
To select a channel within the current
category: Press the “ ” or “ ” button of
“SEEK/TRACK”. The radio will change up
or down to a channel within the current
channel category.
To scan the currently selected channel
category: Touch “SCAN”. “SCAN” ap-
pears on the screen. The radio will find the
next channel in the same channel catego-
ry, stay there for a few seconds, and then
scan again. To select a channel, touch
“SCAN” again.
1Touching “Text” displays the artist
name and song title you are currently
listening to.
SELECTING A CHANNEL
Tune in the desired channel using one
of the following methods.
DISPLAYING THE TITLE AND
NAME
INFORMATION
Up to 64 alphanumeric characters can
be displayed. (Some information will not
be fully displayed.)
115
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
IF THE SATELLITE RADIO TUNER MALFUNCTIONS
When problems occur with the XM® tuner, a message will appear on the screen.
Referring to the table below to identify the problem, take the suggested corrective
action.
Message Explanation
Ck Antenna
The XM® antenna is not connected. Check whether the XM® an-
tenna cable is attached securely.
A short circuit occurs in the antenna or the surrounding antenna
cable. See a Toyota certified dealer for assistance.
Ch Unauth
You have not subscribed to XM® Satellite Radio. The radio is be-
ing updated with the latest encryption code. Contact XM® Satel-
lite Radio for subscription information. When a contract is
canceled, you can choose “CH000” and all free-to-air channels.
The premium channel you selected is not authorized. Wait for
about 2 seconds until the radio returns to the previous channel or
“CH001”. If it does not change automatically, select another
channel. To listen to the premium channel, contact XM® Satellite
Radio.
No Signal The XM® signal is too weak at the current location. Wait until your
vehicle reaches a location with a stronger signal.
Loading The unit is acquiring audio or program information. Wait until the
unit has received the information.
Ch Off Air The channel you selected is not broadcasting any programming.
Select another channel.
----- There is no song/program title or artist name/feature associated
with the channel at that time. No action is required.
Ch Unavail
The channel you selected is no longer available. Wait for about 2
seconds until the radio returns to the previous channel or
“CH001”. If it does not change automatically, select another
channel.
INFORMATION
Contact the XM® Listener Care Center at 1-800-967-2346 (U.S.A.) or 1-877-209-0079
(Canada).
116
1. AUDIO SYSTEM OPERATION
NOTICE
This equipment has been tested and
found to comply with the limits for a
class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable protec-
tion against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed
and used in accordance with the instruc-
tions, may cause harmful interference to
radio communications. However, there
is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful
interference to radio or television recep-
tion, which can be determined by turning
the equipment off and on, the user is
encouraged to try to correct the interfer-
ence by one or more of the following
measures:
Reorient or relocate the receiving
antenna.
Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet
on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
Information to user
Alternation or modifications carried
out without appropriate authorization
may invalidate the users right to
operate the equipment.
INFORMATION
This XM® tuner supports “Audio
Services” (Music and Talk) of only XM®
Satellite Radio and “Text Information*”
linked to the respective “Audio
Services”.
*: Text Information includes, Station
Name, (Artist) Name, (Song) Title and
Category Name.
117
4
AUDIO SYSTEM
1. AUDIO SYSTEM OPERATION
5. CD PLAYER OPERATION
1Insert a disc with the label side up.
zWhen a disc is correctly inserted into the
slot, the CD player will automatically start
playing from the first track or the first file of
the first folder on a disc.
1Press the button.
zThe disc will be ejected.
The CD player can play audio CDs, CD
text and MP3/WMA discs.
(a)Audio CD, CD text (see page 118)
(b)MP3/WMA disc (see page 120)
For appropriate discs for this player,
see “AUDIO SYSTEM OPERATING
HINTS” on page 144.
INSERTING OR EJECTING A
DISC
INSERTING A DISC
INFORMATION
If the label is facing down, “Check DISC”
will appear on the screen.
The player is intended for use with 12
cm (4.7 in.) discs only. To play 8 cm (3
in.) discs, use an adaptor.
NOTICE
Do not stack up two discs for insertion,
or it will cause damage to the CD player.
Insert only one disc into the slot at a
time.
Never try to disassemble or oil any part
of the CD player. Do not insert anything
other than a disc into the slot.
EJECTING A DISC
118
1. AUDIO SYSTEM OPERATION
1Press the “AUDIO” button.
zThe audio system turns on in the last
mode used.
2Touch “Source on the screen.
3Touch “DISC” on the screen.
zIf a CD-TEXT disc is inserted, the title of
the track and disc currently being played
will be displayed.
: Touch to pause the track.
: Touch to resume playing the track.
1Press and hold the “” or “” of the
“SEEK/TRACK” button to fast forward
or reverse. When the button is re-
leased, the player will start playing
from that position.
SWITCHING TO CD MODE
INFORMATION
If no disc is in the slot, “DISC” cannot
be selected. Insert a disc into the slot.
PLAYING AN AUDIO CD
zWhen you touch , you can adjust
sound settings. (See pages 104 and
105)
INFORMATION
The progress bar indicator does not
always correspond to the actual elapsed
playback position.
FAST FORWARD AND
REVERSE
119
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
“SEEK/TRACK” button: Press the or
“” of “SEEK/TRACK” button to select a
desired track.
“TUNE SCROLL” knob: Turn this knob to
select a desired track. Also, the knob can
be used for selection from the list display.
Track list: A desired track can be selected
from a list.
zTouch “Tracks on the screen. The list
will be displayed.
zTouch a desired track. The player will start
playing the selected track from the begin-
ning.
zTouch or to scroll the list.
zIf appears to the right of titles, the
complete titles are too long for the display.
Touch this screen button to scroll to titles.
SELECTING A DESIRED
TRACK
Select a desired track using one of the
following methods.
120
1. AUDIO SYSTEM OPERATION
(Repeat mode): Use it to automat-
ically repeat the track you are currently lis-
tening to.
zThe repeat mode changes as follows each
time the screen button is touched.
(Random mode): Use it for auto-
matic random selection of the track.
zThe random mode changes as follows
each time the screen button is touched.
zThe title of the file and folder currently
being played will be displayed.
: Touch to pause the file.
: Touch to resume playing the file.
1Press and hold the “” or “” of the
“SEEK/TRACK” button to fast forward
or reverse. When the button is re-
leased, the player will start playing
from that position.
PLAYING REPEAT AND
RANDOM ORDER
: Repeating the track
: OFF
:Playing the tracks in ran-
dom order
:OFF
PLAYING A MP3/WMA DISC
zWhen you touch , you can adjust
sound settings. (See pages 104 and
105)
INFORMATION
The progress bar indicator does not
always correspond to the actual elapsed
playback position.
FAST FORWARD AND
REVERSE
121
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
“SEEK/TRACK” button: Press the or
“” of “SEEK/TRACK” button to select a
desired file.
“TUNE SCROLL” knob: Turn this knob to
select a desired file. Also, the knob can be
used for selection from the list display.
File list: A desired file can be selected
from a list.
zTouch “Files” on the screen. The list will
be displayed.
zTouch a desired file. The player will start
playing the selected file from the begin-
ning.
zTouch or to scroll the list.
zIf appears to the right of titles, the
complete titles are too long for the display.
Touch this screen button to scroll to titles.
1Touch “Folders” on the screen. The
folder list will be displayed.
2Touch a desired folder from the list.
The file list for the folder will be dis-
played.
zWhen a desired file is touched, the player
will start playing the file.
zTouch or to scroll the list.
zIf appears to the right of titles, the
complete titles are too long for the display.
Touch this screen button to scroll to titles.
SELECTING A DESIRED FILE
Select a desired file using one of the
following methods.
SELECTING A DESIRED
FOLDER
122
1. AUDIO SYSTEM OPERATION
(Repeat mode): Use it to automat-
ically repeat the file or folder you are cur-
rently listening to.
zThe repeat mode changes as follows each
time the screen button is touched.
(Random mode): Use it for auto-
matic random selection of the file.
zThe random mode changes as follows
each time the screen button is touched.
PLAYING REPEAT AND
RANDOM ORDER
:Repeating the file
:Repeating the folder
:OFF
:Playing the files on the fold-
er in random order
:Playing the files in all the
folders in random order
:OFF
123
4
AUDIO SYSTEM
1. AUDIO SYSTEM OPERATION
6. USB MEMORY/iPod OPERATION
1Open the cover of the USB/AUX port
and connect a USB memory or iPod
using an iPod cable.
zThe USB/AUX port is located on the
instrument panel, or in the console box or
glove box etc. The location and design are
different depending on the vehicle. For
details, see the Pictorial index of “Owner’s
Manual.
zTurn on the power of the USB memory or
iPod if it is not turned on.
zIf a USB memory or iPod is inserted, it
starts playing automatically. As soon as it
is ready to play, the audio control screen is
shown automatically.
The system enables users to enjoy
music played from a USB memory or
iPod on the vehicle's speakers.
CAUTION
Do not operate the player’s controls or
connect the USB memory or iPod while
driving.
NOTICE
Do not leave your portable player in the
vehicle. The temperature inside may rise
to a level that could damage the portable
player.
Do not press down on or apply unneces-
sary pressure to the portable player
while it is connected as this may dam-
age the portable player or its terminal.
Do not insert foreign objects into the
USB port as this may damage the porta-
ble player or its terminal.
INFORMATION
This system has a charging function for
iPods.
When the battery level of an iPod is very
low, the iPod may not operate. If so,
charge the iPod before use.
Depending on the portable player that is
connected to the system, certain func-
tions may not be available. If a function
is unavailable due to a malfunction, dis-
connecting your portable player and
reconnecting it may resolve the problem.
When an iPod does not operate, update
the software of the iPod to the latest ver-
sion, and then retry. For supported mod-
els and software versions, see page
145.
This system supports MTP devices.
CONNECTING A USB
MEMORY OR iPod
124
1. AUDIO SYSTEM OPERATION
1Press the “AUDIO” button.
zThe audio system turns on in the last
mode used.
2Touch “Source.
3Touch “USB” or “iPod”.
PLAY AND PAUSE
: Touch to pause the song.
: Touch to resume playing the song.
SWITCHING TO USB OR iPod
MODE
INFORMATION
If no USB memory or iPod is connected,
“USB or “iPod” cannot be selected.
Connect a USB memory or iPod to the
USB port.
PLAYING A USB MEMORY OR
iPod
PLAYING A SONG
The title of the album, song and artist
name of the song currently being lis-
tened to will be displayed.
zWhen you touch , you can adjust
sound settings. (See pages 104 and
105)
INFORMATION
The progress bar indicator does not
always correspond to the actual elapsed
playback position.
USB memory only: If the song’s data
does not contain an ID3 tag, the file and
folder name will be displayed instead of
the song and album title. Please note
that the file name will not include the
file’s extension.
125
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
FAST FORWARD AND REVERSE
1Press and hold the “” or “” of the
“SEEK/TRACK” button to fast forward
or reverse. When the button is re-
leased, the player will start playing
from that position.
SELECTING A PLAYLIST
1Touch “Browse.
2Touch the desired list.
zTouch the desired item to display its list.
Continue to touch the applicable screen
button until its song list is displayed.
3Touch the desired song.
SELECTING A DESIRED SONG
Songs can be sorted and selected from
various playlists.
zThe selecting playlist screen is can be
displayed from the “Options” screen.
Touch “Options” and then touch
“Browse For Music” on the next
screen.
126
1. AUDIO SYSTEM OPERATION
SELECTING BY LIST
1Touch “List.
2Touch the desired song.
SELECTING A DESIRED SONG US-
ING “SEEK/TRACK” BUTTON OR
“TUNE SCROLL” KNOB
“SEEK/TRACK” button: Press the “” or
“” of the “SEEK/TRACK” button to se-
lect a desired song.
“TUNE SCROLL” knob: Turn to select a
desired song.
INFORMATION
USB memory only: Files that do not con-
tain song title and/or album information
will be displayed as “Unknown” in the
“Artist” and/or “Album” list.
While the media is being synchronized,
a pop-up window is displayed. When
synchronization is complete, a pop-up
window will be displayed and the func-
tion will be available. Touch “OK to
return to the previous screen.
The desired song can be selected from
the current playlist.
zThe list is can be displayed from the
“Options” screen. Touch “Options” and
then touch “Current Playlist” on the
next screen.
127
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
1Touch the cover art.
2A list of all the songs from the album
will be displayed.
3Touch the desired song.
1Touch “Play More Like This”.
zA pop-up window is displayed until the
playlist is created. If you touch “Cancel”
on the screen, the creation of the new
playlist is cancelled.
zAs soon as the new playlist is ready, the
first similar song starts playing.
“Play More Like This” SETTING
1Touch “Options”.
COVER ART FUNCTION
The album, that the song currently be-
ing listened to is from, is called up so
that a song from it can be selected.
INFORMATION
If a song other than the one currently
being listened to is selected, the current
playlist is updated and will include all the
songs from the album being listened to.
It may take time to display iPod cover
art. Only iPod cover art that is saved in
JPEG format can be displayed.
When Audio book or Podcast playlists
are selected, this function is not avail-
able.
PLAYING “PLAY MORE LIKE
THIS” FUNCTION
The system creates a new playlist con-
taining songs similar to the one cur-
rently being listened to.
The size of the playlist of similar songs
can be set.
128
1. AUDIO SYSTEM OPERATION
2Touch “Play More Like This Set-
tings”.
3Touch the desired size of the playlist.
4Touch .
FROM THE AUDIO CONTROL
SCREEN
1Touch or .
(Repeat mode): Use it to automatical-
ly repeat the song you are currently listen-
ing to.
zThe repeat mode changes as follows each
time the screen button is touched.
(Random mode): Use it for automatic
random order in the current playlist.
zThe random mode changes as follows
each time the screen button is touched.
REPEAT AND RANDOM PLAY
FUNCTIONS
Repeat and random play functions are
available.
: Repeating the song
:OFF
: Playing the songs in random
order
:OFF
129
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
FROM THE “Options” SCREEN
1Touch “Options”.
2Touch “Random or “Repeat Track”.
zTo cancel repeat or random order, touch
“Random” or “Repeat Track” again.
INFORMATION
When “Random” is on, the songs in the
current playlist can be played in random
order.
130
1. AUDIO SYSTEM OPERATION
7. AUX DEVICE OPERATION
1Open the cover of the USB/AUX port
and connect a portable audio device.
zThe USB/AUX port is located on the
instrument panel, or in the console box or
glove box etc. The location and design are
different depending on the vehicle. For
details, see the Pictorial index of “Owner’s
Manual”.
Connecting a portable audio device
with the AUX port enables users to en-
joy music via the vehicle speakers.
CAUTION
Do not connect a portable audio device
or operate the device controls while driv-
ing.
NOTICE
Do not leave the portable audio device
in the car. In particular, high tempera-
tures inside the vehicle may damage the
device.
Do not push down on or apply unneces-
sary pressure to the portable audio
device while it is connected as this may
damage the device or its terminal.
Do not insert foreign objects into the
AUX port as this may damage the porta-
ble audio device or its terminal.
CONNECTING A PORTABLE
AUDIO DEVICE
131
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
1Press the “AUDIO” button.
zThe audio system turns on in the last
mode used.
2Touch “Source” on the screen.
3Touch “AUX” on the screen.
zOnly the volume can be adjusted using
the audio system controls. The remaining
controls need to be operated on the porta-
ble audio device itself.
SWITCHING TO AUX MODE
INFORMATION
If no portable audio device is connected,
“AUX” cannot be selected. Connect the
portable audio device to the AUX port.
PLAYING A PORTABLE
AUDIO DEVICE
zWhen you touch , you can adjust
sound settings. (See pages 104 and
105)
132
1. AUDIO SYSTEM OPERATION
8. Bluetooth® AUDIO OPERATION
Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
The Bluetooth® audio system enables
users to enjoy music played on a por-
table player from the vehicle speaker
via wireless communication.
If your portable player does not support
Bluetooth®, the Bluetooth® audio
system will not function.
CAUTION
Do not operate the player’s controls or
connect to the Bluetooth® audio system
while driving.
NOTICE
Do not leave your portable audio player
in the car. In particular, high tempera-
tures inside the vehicle may damage the
portable audio player.
INFORMATION
In the following conditions, the system
may not function.
The portable audio player is turned
off.
• The portable audio player is not con-
nected.
The portable audio player has a low
battery.
Depending on the portable audio player
that is connected to the system, certain
functions may not be available.
It may take time, the phone connection
is carried out during Bluetooth® audio
play.
INFORMATION
Portable audio players must correspond
to the following specifications in order to
be connected to the Bluetooth® audio
system. However, please note that some
functions may be limited depending on
the type of portable audio player.
• Bluetooth® Specification
Ver.1.1 or higher
(Recommended: Ver.2.1+EDR or
higher)
• Profile
A2DP (Advanced Audio Distribution
Profile)
Ver.1.0 or higher
(Recommended: Ver.1.2 or higher)
AVRCP (Audio/Video Remote Con-
trol Profile)
Ver.1.0 or higher
(Recommended: Ver.1.4 or higher)
133
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
1Press the “AUDIO” button.
zThe audio system turns on in the last
mode used.
2Touch “Source” on the screen.
3Touch “Bluetooth.
zIf a Bluetooth® audio device is not con-
nected, the connecting Bluetooth® audio
screen will automatically appear.
: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
CAUTION
FCC WARNING: Changes or modifica-
tions not expressly approved by the
party responsible for compliance could
void the user’s authority to operate the
equipment.
CAUTION: Radio Frequency Radiation
Exposure
This equipment complies with FCC radi-
ation exposure limits set forth for uncon-
trolled equipment and meets the FCC
radio frequency (RF) Exposure Guide-
lines in Supplement C to OET65 and
RSS-102 of the IC radio frequency (RF)
Exposure rules. This equipment has
very low levels of RF energy that it
deemed to comply without maximum
permissive exposure evaluation (MPE).
But it is desirable that it should be
installed and operated with at least 20
cm and more between the radiator and
person’s body (excluding extremities:
hands, wrists, feet and ankles).
Co-location: This transmitter must not be
co-located or operated in conjunction
with any other antenna or transmitter.
SWITCHING TO Bluetooth®
AUDIO MODE
134
1. AUDIO SYSTEM OPERATION
CONNECTING FROM THE SYSTEM
1Switching to Bluetooth® audio mode.
(See page 133.)
2Touch Search Bluetooth Devices”.
3Touch “Search for Bluetooth Devic-
es”.
zWhen a Bluetooth® device is currently
connected, a pop-up window is displayed.
To disconnect it, touch “Yes”.
: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
CONNECTING Bluetooth®
AUDIO
In order to use the Bluetooth® audio
system, it is necessary to pair a porta-
ble player and connect the audio pro-
file (A2DP) with the system. (In this
manual, pairing refers to a Bluetooth®
device connecting with the system.
Connecting refers to the paired de-
vice’s profile(s) being connected to the
system.)
Once you have connected a device
with audio profile (A2DP), you can en-
joy your music on the vehicle’s audio
system.
If you have not yet connected a porta-
ble player with audio profile (A2DP),
you must first pair a portable player
with audio profile (A2DP) according to
the following procedures. Connect
your portable player with audio profile
(A2DP) after bringing the vehicle to a
complete stop.
zSee “Bluetooth® SETTINGS” on page
202 of additional registration when reg-
istering.
CONNECTING Bluetooth®
AUDIO
135
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
4The following screen will be displayed
while searching for a Bluetooth® de-
vice.
zTo cancel this function, touch “Cancel”.
5Touch the device to be paired.
zConnectable Bluetooth® devices are listed
on the display.
6The following screen will be displayed.
zTo cancel this function, touch “Cancel”.
7Confirm the PIN.
XIf the device supports SSP (Secure Sim-
ple Pairing)
zConfirm the PIN displayed on the screen,
and then touch “Accept”.
XIf the device does not supports SSP (Se-
cure Simple Pairing)
zInput the PIN displayed on the screen into
your portable player.
8The following screen will be displayed
when pairing is complete.
9The system waits for connection re-
quests coming from the paired device.
All requested profiles are connected
automatically.
zIf the automatic connection failed, the fol-
lowing screen will be displayed. Touch
“Connect for Music”.
zOnce a portable player has been con-
nected, it will be automatically connected
whenever the engine switch is in the
“ACC” or “ON” position.
INFORMATION
For details on device detection and
operation of the portable player, refer to
the manual that comes with the portable
audio player.
136
1. AUDIO SYSTEM OPERATION
CONNECTING FROM THE DEVICE
1Switching to Bluetooth® audio mode.
(See page 133.)
2Touch Search Bluetooth Devices”.
3Touch “Make Discoverable”.
zWhen a Bluetooth® device is currently
connected, a pop-up window is displayed.
To disconnect it, touch “Yes”.
4The following screen will be displayed.
zTo cancel this function, touch “Cancel”.
: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
5Confirm the PIN.
XIf the device supports SSP (Secure Sim-
ple Pairing)
zConfirm the PIN displayed on the screen,
and then touch “Accept”.
XIf the device does not supports SSP (Se-
cure Simple Pairing)
zInput the PIN displayed on the screen into
your portable player.
137
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
zIf the Bluetooth® device is disconnected
on purpose, such as it was turned off, this
does not happen. Reconnect it manually
using either of the following methods:
Select a portable player again. (See
page 206.)
Connect the audio profile. (See page
203.)
PLAY AND PAUSE
: Touch to pause the song.
: Touch to resume playing the song.
RECONNECTING Bluetooth®
AUDIO
If a portable player is disconnected due
to poor reception from the Bluetooth®
network when the engine switch is in
the “ACC” or “ON” position, the system
will automatically reconnect the porta-
ble player.
PLAYING Bluetooth® AUDIO
PLAYING A SONG
The title of the song, album and artist
name of the song currently being lis-
tened to will be displayed.
zWhen you touch , you can adjust
sound settings. (See pages 104 and
105)
INFORMATION
The progress bar indicator does not
always correspond to the actual elapsed
playback position.
If the song’s data does not contain an
ID3 tag, the file and folder name will be
displayed instead of the song and album
title. Please note that the file name will
not include the file’s extension.
Bluetooth® audio screen may differ
depending on your device.
138
1. AUDIO SYSTEM OPERATION
FAST FORWARD AND REVERSE
1Press and hold the “ ” or “ ” of the
“SEEK/TRACK” button to fast forward
or reverse. When the button is re-
leased, the player will start playing
from that position.
SELECTING A PLAYLIST
1Touch “Browse”.
2Touch the desired list.
zTouch the desired item to display its list.
Continue to touch the applicable screen
button until its song list is displayed.
3Touch the desired song.
SELECTING A DESIRED SONG
Songs can be sorted and selected from
various playlists.
zThe selecting playlist screen is can be
displayed from the “Options” screen.
Touch “Options and then touch
“Browse For Music” on the next
screen.
INFORMATION
Files that do not contain song title and/or
album information will be displayed as
“Unknown” in the “Artist” and/or “Album”
list.
This function may not be available
depending on the portable audio player.
139
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
SELECTING BY LIST
1Touch “List”.
2Touch the desired song.
SELECTING A DESIRED SONG US-
ING “SEEK/TRACK” BUTTON OR
“TUNE SCROLL” KNOB
“SEEK/TRACK” button: Press the “ ” or
“”of the “SEEK/TRACK” button to select
a desired song.
“TUNE SCROLL” knob: Turn to select a
desired song.
The desired song can be selected from
the current playlist.
zThe list is can be displayed from the
“Options” screen. Touch “Options” and
then touch “Current Playlist” on the
next screen.
INFORMATION
This function may not be available
depending on the portable audio player.
140
1. AUDIO SYSTEM OPERATION
FROM THE AUDIO CONTROL
SCREEN
1Touch or .
(Repeat mode): Use it to automatical-
ly repeat the song you are currently listen-
ing to.
zThe repeat mode changes as follows each
time the screen button is touched.
(Random mode): Use it for automatic
random order in the current playlist.
zThe random mode changes as follows
each time the screen button is touched.
FROM THE “Options” SCREEN
1Touch “Options.
2Touch “Random” or “Repeat Track”.
zTo cancel repeat or random order, touch
“Random” or “Repeat Track” again.
REPEAT AND RANDOM PLAY
FUNCTIONS
Repeat and random play functions are
available.
: Repeating the song
:OFF
: Playing the songs in random
order
:OFF
INFORMATION
When “Random” is on, the songs in the
current playlist can be played in random
order.
141
4
AUDIO SYSTEM
1. AUDIO SYSTEM OPERATION
9. STEERING SWITCHES
zThe design and switch position may differ
depending on the vehicle. For details, see
the Pictorial index of “Owners Manual.
zDetails of the specific switches, controls,
and features are described below.
Volume control switch
zPress the “+ side to increase the volume.
The volume continues to increase while
the switch is being pressed.
zPress the “-” side to decrease the vol-
ume. The volume continues to decrease
while the switch is being pressed.
“” “” switch
XRadio
To select a preset station: Press the “”
or “ switch.
To seek a radio station: Press and hold
the “” or “” switch until you hear a beep.
If you press either the “” or “” switch in
seek mode, the seek mode will be can-
celled.
XCD player
To select a desired track or file:Press
the “” or “” switch.
To select a desired folder (MP3/WMA):
Press and hold the “” or “” switch until
you hear a beep.
XUSB memory/iPod
To select a desired song: Press the “”
or “ switch.
Fast forward and reverse: Press and
hold the “” or “” switch until you hear a
beep.
XBluetooth® audio player
To select a desired song: Press the “”
or “ switch.
Fast forward and reverse: Press and
hold the “” or “” switch until you hear a
beep.
“MODE” switch
zPress the “MODE switch to select an
audio mode. Each press changes the
mode sequentially if the desired mode is
ready to use.
zTo turn the audio system on, press the
“MODE” switch.
zPress and hold the “MODE switch until
you hear a beep and the music will pause
or be muted. By the same operation, it is
released.
Some parts of the audio system can be
adjusted with the switches on the
steering wheel.
STEERING SWITCHES (WITH
TWO DIRECTION STEERING
SWITCH)
No. Switch
Volume control switch
“” “” switch
“MODE” switch
142
1. AUDIO SYSTEM OPERATION
zThe design and switch position may differ
depending on the vehicle. For details, see
the Pictorial index of “Owners Manual”.
zDetails of the specific switches, controls,
and features are described below.
Volume control switch
zPress the “+” side to increase the volume.
The volume continues to increase while
the switch is being pressed.
zPress the “- side to decrease the vol-
ume. The volume continues to decrease
while the switch is being pressed.
“”
“” “” switch
XRadio
To select a preset station: Press the “”
or “ side of the switch. Repeat this to se-
lect the next preset station.
To seek a station: Press and hold the “
or “ ” side of the switch until a beep is
heard. Repeat this to find the next station.
If either side of the switch is pressed dur-
ing seek mode, seeking will be canceled.
To change the preset page: The radio’s
preset page can be changed by pressing
the “ ” or ” side of the switch.
XCD player
To select a desired track or file: Press
the “ ” or “ ” side of the switch until the
desired track or file to play is selected. To
return to the beginning of the current track
or file, press the “ ” side of the switch once
quickly.
To select a desired folder (MP3/WMA):
Press the “ or “ switch to change to
the next or the previous folder.
XUSB memory/iPod
To select a desired song: Press the “
or “ ” switch until the desired song is se-
lected.
Fast forward and reverse: Press and
hold the “” or “” switch until you hear a
beep.
XBluetooth® audio player
To select a desired song: Press the “
or “ ” side of the switch until the desired
song is selected.
Fast forward and reverse: Press and
hold the “” or “” switch until you hear a
beep.
STEERING SWITCHES (WITH
FOUR DIRECTION STEERING
SWITCH)
No. Switch
Volume control switch
“” “” switch
“MODE/HOLD” switch
Back switch
Enter switch
143
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
“MODE/HOLD” switch
zPress the “MODE/HOLD” switch to select
an audio mode. Each press changes the
mode sequentially if the desired mode is
ready to use.
zTo turn the audio system on, press the
“MODE/HOLD” switch.
zPress and hold the “MODE/HOLD” switch
until you hear a beep and the music will
pause or be muted. By the same opera-
tion, it is released.
Back switch
zPress the back switch to return to the pre-
vious screen.
Enter switch
zWhen in radio mode, pressing the enter
switch returns to the preset screen.
zWhen in media mode, pressing the enter
switch returns to the list screen.
144
1. AUDIO SYSTEM OPERATION
10. AUDIO SYSTEM OPERATING HINTS
Fading and drifting stations: Generally,
the effective range of FM is about 25 miles
(40 km). Once outside this range, you may
notice fading and drifting, which increase
with the distance from the radio transmit-
ter. They are often accompanied by distor-
tion.
Multi-path: FM signals are reflective, mak-
ing it possible for two signals to reach your
antenna at the same time. If this happens,
the signals will cancel each other out,
causing a momentary flutter or loss of re-
ception.
Static and fluttering: These occur when
signals are blocked by buildings, trees, or
other large objects. Increasing the bass
level may reduce static and fluttering.
Station swapping: If the FM signal you
are listening to is interrupted or weakened,
and there is another strong station nearby
on the FM band, your radio may tune in the
second station until the original signal can
be picked up again.
Fading: AM broadcasts are reflected by
the upper atmosphere especially at
night. These reflected signals can interfere
with those received directly from the radio
station, causing the radio station to sound
alternately strong and weak.
Station interference: When a reflected
signal and a signal received directly from a
radio station are very nearly the same fre-
quency, they can interfere with each other,
making it difficult to hear the broadcast.
Static: AM is easily affected by external
sources of electrical noise, such as high
tension power lines, lightening, or electri-
cal motors. This results in static.
NOTICE
To avoid damaging the audio system:
Be careful not to spill beverages over
the audio system.
Do not put anything other than on
appropriate discs into the CD player
slot.
INFORMATION
The use of a cellular phone inside or
near the vehicle may cause a noise from
the speakers of the audio system which
you are listening to. However, this does
not indicate a malfunction.
RADIO RECEPTION
Usually, a problem with radio reception
does not mean there is a problem with
your radio it is just the normal result
of conditions outside the vehicle.
For example, nearby buildings and ter-
rain can interfere with FM reception.
Power lines or telephone wires can in-
terfere with AM signals. And of course,
radio signals have a limited range, and
the farther you are from a station, the
weaker its signal will be. In addition, re-
ception conditions change constantly
as your vehicle moves.
Here are some common reception
problems that probably do not indicate
a problem with your radio.
FM
AM
145
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
zCargo loaded on the roof luggage carrier,
especially metal objects, may adversely
affect the reception of XM® Satellite
Radio.
zAlternation or modifications carried out
without appropriate authorization may
invalidate the users right to operate the
equipment.
z“Made for iPod” and “Made for iPhone”
means that an electronic accessory has
been designed to connect specifically to
iPod, or iPhone, respectively, and has
been certified by the developer to meet
Apple performance standards.
zApple is not responsible for the operation
of this device or its compliance with safety
and regulatory standards.
ziPhone, iPod, iPod classic, iPod nano,
iPod shuffle, and iPod touch are trade-
marks of Apple Inc., registered in the U.S.
and other countries.
Depending on differences between mod-
els or software versions etc., some models
listed above might be incompatible with
this system.
iPad is not compatible with this system.
XM®
iPod
ABOUT iPod
COMPATIBLE MODELS
Model Generation Software
Version
iPod 5G 1.3.0
iPod classic
1G 1.1.2
2G 2.0.1
2009 (160GB) 2.0.4
iPod nano
1G 1.3.1
3G 1.1.3
4G 1.0.4
5G 1.0.2
6G 1.0.0
iPod touch
1G iOS 3.1.3
2G
iOS 3.1.3
iOS 4.2.1
2009 (8GB)
3G
4G iOS 4.2.1
iPhone
iPhone iOS 3.1.3
iPhone 3G iOS 3.1.3
iOS 4.2.1
iPhone 3GS
iPhone 4 iOS 4.2.1
146
1. AUDIO SYSTEM OPERATION
zUSB memory that can be used for MP3
and WMA playback.
USB communication formats: USB 2.0
FS (12 Mbps)
File formats: FAT 16/32 (Windows®)
Correspondence class: Mass storage
class
zYour CD player is intended for use with
4.7 in. (12 cm) discs only. To play 3 in. (8
cm) discs, use an adaptor.
zExtremely high temperatures can keep
your CD player from working. On hot
days, use air conditioning to cool the vehi-
cle interior before you listen to a disc.
zBumpy roads or other vibrations may
make your CD player skip.
zIf moisture gets into your CD player, you
may not hear any sound even though your
CD player appears to be working. Remove
the discs from the CD player and wait until
it dries.
zUse only discs marked as shown above.
The following products may not be play-
able on your CD player.
• SACDs
dts CDs
Copy-protected CDs
•Video CDs
XSpecial shaped discs
XTransparent/translucent discs
USB MEMORY
CARING FOR YOUR CD
PLAYER AND DISCS
CAUTION
CD player uses an invisible laser beam
which could cause hazardous radiation
exposure if directed outside the unit. Be
sure to operate the CD player correctly.
Audio CDs
147
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
XLow quality discs
XLabeled discs zHandle discs carefully, especially when
you are inserting them. Hold them on the
edge and do not bend them. Avoid getting
fingerprints on them, particularly on the
shiny side.
zDirt, scratches, warping, pin holes, or
other disc damage could cause the CD
player to skip or to repeat a section of a
track. (To see a pin hole, hold the disc up
to the light.)
zRemove discs from the CD player when
you are not using them. Store them in their
plastic cases away from moisture, heat,
and direct sunlight.
zTo clean a disc: Wipe it with a soft, lint-
free cloth that has been dampened with
water. Wipe in a straight line from the cen-
ter to the edge of the disc (not in a circle).
Do not use a conventional record cleaner
or anti-static device.
NOTICE
Do not use special shaped, transparent/
translucent, low quality or labeled discs
such as those shown in the illustrations.
The use of such discs may damage the
player, or it may be impossible to eject
the disc.
This system is not designed for use of
Dual Disc. Do not use Dual Disc
because it may cause damage to the
player.
Correct Wrong
148
1. AUDIO SYSTEM OPERATION
zMP3 (MPEG Audio Layer 3) and WMA
(Windows Media Audio) are audio com-
pression standards.
zThe MP3/WMA player can play MP3 and
WMA files on CD-ROM, CD-R and CD-
RW discs.
The unit can play disc recordings compati-
ble with ISO 9660 level 1,2 (Romeo Joliet)
and UDF (2.01 or lower) file system.
zWhen naming an MP3 or WMA file, add
the appropriate file extension (.mp3 or
.wma).
zThe MP3/WMA player plays back files
with .mp3 or .wma file extensions as MP3
or WMA files. To prevent noise and play-
back errors, use the appropriate file exten-
sions.
zThe player can play only the first session
using multi-session compatible CDs.
zMP3 files are compatible with the ID3 Tag
Ver. 1.0, Ver. 1.1, Ver. 2.2, and Ver. 2.3
formats. The unit cannot display disc title,
track title and artist name in other formats.
zUSB memory: MP3 files are compatible
with the ID3 Tag Ver. 1.0, Ver. 1.1, Ver.
2.2, Ver. 2.3 and Ver. 2.4 formats. The unit
cannot display track title and artist name
in other formats.
zWMA files can contain a WMA tag that is
used in the same way as an ID3 tag. WMA
tags carry information such as track title,
artist name.
zThe sound quality of MP3/WMA files gen-
erally improves with higher bit rates. In
order to achieve a reasonable level of
sound quality, files recorded with a bit rate
of at least 128 kbps are recommended.
MP3 files:
MPEG 1 AUDIO LAYER 3 32, 44.1, 48
kHz
MPEG2 AUDIO LAYER3 16, 22.05, 24
kHz
WMA files for WMA player:
Ver. 7, 8, 9 CBR 32, 44.1, 48 kHz
WMA files for USB memory:
Ver. 7, 8, 9 HIGH PROFILE 32, 44.1, 48
kHz
MP3 files for MP3 player:
MPEG1 LAYER3 32 to 320 kbps
MPEG2 LSF LAYER3 8 to 160 kbps
MP3 files for USB memory:
MPEG 1 AUDIO LAYER 2, 3 32 to 320
kbps
MPEG 2 AUDIO LAYER 2, 3 8 to 160
kbps
WMA files for WMA player:
Ver. 7, 8 CBR 48 to 192 kbps
Ver. 9 CBR 48 to 320 kbps
WMA files for USB memory:
Ver. 7, 8, 9 CBR 48 to 320 kbps
zM3u playlists are not compatible with the
audio player.
zMP3i (MP3 interactive) and MP3PRO for-
mats are not compatible with the audio
player.
zThe player is compatible with VBR (Vari-
able Bit Rate).
zWhen playing back files recorded as VBR
(Variable Bit Rate) files, the play time will
not be correctly displayed if fast-forward or
reverse operations are used.
zIt is not possible to check folders that do
not include MP3/WMA files.
MP3/WMA FILES SAMPLING FREQUENCY
PLAYABLE BIT RATES
149
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
zMP3/WMA files in folders up to 8 levels
deep can be played. However, the start of
playback may be delayed when using
discs containing numerous levels of fold-
ers. For this reason, we recommend creat-
ing discs with no more than two levels of
folders.
zWMA files Ver. 9 depends on “Windows
Media® Audio Standard”.
zThe play order of the compact disc with
the structure shown on the left is as fol-
lows:
zMP3/WMA player: It is possible to play up
to 192 folders or 255 files on one disc.
zUSB memory:
Maximum number of folder in device:
3000
Maximum number of files in one folder:
255
Maximum number of files in device: 9999
zThe order changes depending on the PC
and MP3/WMA encoding software you
use.
zCD-R/CD-RW discs that have not been
subject to the “finalizing process” (a pro-
cess that allows discs to be played on a
conventional CD player) cannot be
played.
zIt may not be possible to play CD-R/CD-
RW discs recorded on a music CD
recorder or a personal computer because
of disc characteristics, scratches or dirt on
the disc, or dirt, condensation, etc. on the
lens of the unit.
zIt may not be possible to play discs
recorded on a personal computer depend-
ing on the application settings and the
environment. Record with the correct for-
mat. (For details, contact the appropriate
application manufacturers of the applica-
tions.)
zCD-R/CD-RW discs may be damaged by
direct exposure to sunlight, high tempera-
tures or other storage conditions. The unit
may be unable to play some damaged
discs.
zIf you insert a CD-RW disc into the MP3/
WMA player, playback will begin more
slowly than with a conventional CD or CD-
R disc.
zRecordings on CD-R/CD-RW cannot be
played using the DDCD (Double Density
CD) system.
001.mp3
002.wma
Folder 1
003.mp3
Folder 2
004.mp3
005.wma
Folder 3
006.mp3
001. mp3 002. wma. . . 006. mp3
CD-R AND CD-RW DISCS
150
1. AUDIO SYSTEM OPERATION
zThis is a general term that describes the
process of writing data on-demand to CD-
R, etc., in the same way that data is writ-
ten to floppy or hard discs.
zThis is a method of embedding track-
related information in an MP3 file. This
embedded information can include the
track title, the artist’s name, the album
title, the music genre, the year of produc-
tion, comments and other data. The con-
tents can be freely edited using software
with ID3 tag editing functions. Although
the tags are restricted to the number of
characters, the information can be viewed
when the track is played back.
zWMA files can contain a WMA tag that is
used in the same way as an ID3 tag. WMA
tags carry information such as track title,
artist name.
zThis is the international standard for the
formatting of CD-ROM folders and files.
For the ISO 9660 format, there are two
levels of regulations.
zLevel 1: The file name is in 8.3 format (8
character file names, with a 3 character
file extension. File names must be com-
posed of one-byte capital letters and num-
bers. The “_” symbol may also be
included.)
zLevel 2: The file name can have up to 31
characters (including the separation mark
“.” and file extension). Each folder must
contain fewer than 8 hierarchies.
zPlaylists created using “WINAMP” soft-
ware have a playlist file extension (.m3u).
zMP3 is an audio compression standard
determined by a working group (MPEG) of
the ISO (International Standard Organiza-
tion). MP3 compresses audio data to
about 1/10 the size of that on conventional
discs.
zWMA (Windows Media Audio) is an audio
compression format developed by
Microsoft®. It compresses files into a size
smaller than that of MP3 files. The decod-
ing formats for WMA files are Ver. 7, 8,
and 9.
TERMS
PACKET WRITE
ID3 TAG
WMA TAG
ISO 9660 FORMAT
m3u
MP3
WMA
151
1. AUDIO SYSTEM OPERATION
4
AUDIO SYSTEM
Gracenote®
zMusic recognition technology and
related data are provided by
Gracenote®. Gracenote is the industry
standard in music recognition technol-
ogy and related content delivery. For
more information visit
www.gracenote.com.
z
Gracenote® End User License Agree-
ment
This application or device contains
software from Gracenote, Inc. of Em-
eryville, California (“Gracenote”). The
software from Gracenote (the
“Gracenote Software”) enables this
application to perform disc and/or file
identification and obtain music-related
information, including name, artist,
track, and title information
(“Gracenote Data”) from online serv-
ers or embedded databases (collec-
tively, “Gracenote Servers”) and to
perform other functions. You may use
Gracenote Data only by means of the
intended End-User functions of this
application or device.
You agree that you will use Gracenote
Data, the Gracenote Software, and
Gracenote Servers for your own per-
sonal non-commercial use only. You
agree not to assign, copy, transfer or
transmit the Gracenote Software or
any Gracenote Data to any third party.
YOU AGREE NOT TO USE OR EX-
PLOIT GRACENOTE DATA, THE
GRACENOTE SOFTWARE, OR
GRACENOTE SERVERS, EXCEPT
AS EXPRESSLY PERMITTED
HEREIN.
You agree that your non-exclusive li-
cense to use the Gracenote Data, the
Gracenote Software, and Gracenote
Servers will terminate if you violate
these restrictions. If your license termi-
nates, you agree to cease any and all
use of the Gracenote Data, the
Gracenote Software, and Gracenote
Servers. Gracenote reserves all rights
in Gracenote Data, the Gracenote
Software, and the Gracenote Servers,
including all ownership rights. Under
no circumstances will Gracenote be-
come liable for any payment to you for
any information that you provide. You
agree that Gracenote, Inc. may en-
force its rights under this Agreement
against you directly in its own name.
The Gracenote service uses a unique
identifier to track queries for statistical
purposes. The purpose of a randomly
assigned numeric identifier is to allow
the Gracenote service to count que-
ries without knowing anything about
who you are. For more information,
see the web page for the Gracenote
Privacy Policy for the Gracenote ser-
vice.
152
1. AUDIO SYSTEM OPERATION
The Gracenote Software and each
item of Gracenote Data are licensed to
you “AS IS.” Gracenote makes no rep-
resentations or warranties, express or
implied, regarding the accuracy of any
Gracenote Data from in the Gracenote
Servers. Gracenote reserves the right
to delete data from the Gracenote
Servers or to change data categories
for any cause that Gracenote deems
sufficient. No warranty is made that
the Gracenote Software or Gracenote
Servers are error-free or that function-
ing of Gracenote Software or
Gracenote Servers will be uninterrupt-
ed. Gracenote is not obligated to pro-
vide you with new enhanced or
additional data types or categories
that Gracenote may provide in the fu-
ture and is free to discontinue its ser-
vices at any time.
GRACENOTE DISCLAIMS ALL
WARRANTIES EXPRESS OR IM-
PLIED, INCLUDING, BUT NOT LIM-
ITED TO, IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, TI-
TLE, AND NON-INFRINGEMENT.
GRACENOTE DOES NOT WAR-
RANT THE RESULTS THAT WILL BE
OBTAINED BY YOUR USE OF THE
GRACENOTE SOFTWARE OR ANY
GRACENOTE SERVER. IN NO
CASE WILL GRACENOTE BE LIA-
BLE FOR ANY CONSEQUENTIAL
OR INCIDENTAL DAMAGES OR
FOR ANY LOST PROFITS OR LOST
REVENUES.
copyright © 2000 to present
Gracenote
5
153
1
2
3
4
5
6
7
8
9
1. QUICK REFERENCE................... 154
2. HANDS-FREE SYSTEM .............. 157
USING THE PHONE SWITCH............ 158
ABOUT THE PHONE BOOK IN THIS
SYSTEM ........................................... 159
WHEN YOU RELEASE YOUR CAR ... 159
3. CONNECTING A
Bluetooth® PHONE................... 161
CONNECTING A
Bluetooth® PHONE ........................... 161
4. REGISTERING A ENTRY ............ 165
REGISTERING A NEW ENTRY.......... 165
REGISTERING A ENTRY AS
“Speed Dials” .................................... 167
DISPLAYING AND EDITING THE
ENTRY INFORMATION.................... 168
SENDING STORED CONTACTS
TO A USB MEMORY ........................ 169
1. CALLING ON A
Bluetooth® PHONE................... 170
BY DIAL............................................... 170
BY “Stored” LIST ON THE
“Contacts” SCREEN.......................... 170
BY PHONE BOOK............................... 171
BY SPEED DIALS................................ 172
BY CALL HISTORY ............................. 173
CALLING USING A SHORT
MESSAGE......................................... 173
BY POI* CALL...................................... 174
2. RECEIVING CALLS ON A
Bluetooth® PHONE .................. 175
3. TALKING ON A
Bluetooth® PHONE .................. 176
ADJUSTING THE RECEIVER
VOLUME ........................................... 177
SENDING TONES ............................... 177
DIALING A SECOND NUMBER .......... 177
1. SHORT MESSAGE
FUNCTION ................................ 179
RECEIVING A NEW SHORT
MESSAGE......................................... 179
CHECKING RECEIVED SHORT
MESSAGES ...................................... 179
CHECKING SENT SHORT
MESSAGES ...................................... 180
SENDING A NEW SHORT
MESSAGES ...................................... 180
1BASIC INFORMATION BEFORE
OPERATION
2TELEPHONE OPERATION
3SHORT MESSAGE FUNCTION
Bluetooth® HANDS-FREE SYSTEM
*: Point of Interest
154
1. BASIC INFORMATION BEFORE OPERATION
1. QUICK REFERENCE
X“Phone” menu screen
zThe actual design and button position may differ depending on the vehicle. For
details, see Section 3 of “Owner’s Manual”.
Pressing the button allows access to the “Phone” menu screen.
When the button is pressed, the screen that was last displayed is returned
to. Touch to display the “Phone” menu screen.
No. Function Page
Touch to display the “Dial By Number” screen.
A call can be made by dialing the number. 155, 170
Touch to display the “Contacts” screen.
An entry from the list of contacts in the “Stored” screen, “Phone Book”
or “Speed Dials” can be selected and called.
170, 171,
172
Touch to display the “Call History” screen.
An entry from the missed, received or dial call lists can be selected
and called.
173
Touch to display the “Messages” screen.
A list of received and sent short messages and a menu to create new
short messages can be displayed.
179
Touch to display the “Phone” menu screen.
155
1. BASIC INFORMATION BEFORE OPERATION
5
Bluetooth® HANDS-FREE SYSTEM
X“Dial By Number” screen
To display the “Dial By Number” screen, touch “Dial By Number” on the “Phone”
menu screen, or touch on any of the “Phone” screens. The “Dial By Number”
screen can also be displayed by pressing the switch on the steering wheel.
No. Name Function
Shortcut keys Touch the corresponding icon to change to the “Dial By Number”,
“Contacts”, “Call History” or “Messages” screen.
The Name of
phone and pro-
vider
Displaying name of the phone and provider. These information may
not be displayed depending on the phone.
Number keys Touch to input a phone number.
Save the num-
ber screen but-
ton
Touch to register a phone number.
Delete screen
button Touch to delete an input phone number.
Off hook screen
button Touch to make a phone call.
The receiving
area
“R” is displayed when receiving in a Roaming area.
xThe receiving area may not be displayed depending on the
phone.
156
1. BASIC INFORMATION BEFORE OPERATION
The amount of
battery charge
left
The six bars display the charge level of the phone’s battery.
xThe amount displayed does not always correspond with the
amount displayed on the cellular phone. The amount of battery
charge left may not be displayed depending on the phone. This
system does not have a charging function.
xIf this information is not available from the connected phone, the
icon will be shown with a question mark.
The level of re-
ception
The five bars display the level of reception.
xThe level of reception does not always correspond with the level
displayed on the cellular phone.
xThe level of reception may not be displayed depending on the
phone.
xIf this information is not available from the connected phone, the
icon will be shown with a question mark.
Bluetooth® con-
nection The icon indicates an active BT-connection
Short messag-
es information Displays short messages information.
Missed calls in-
formation Displays missed calls information.
INFORMATION
An antenna for the Bluetooth® connection is built into the instrument panel. The system
may not function when you use the Bluetooth® phone in the following conditions and
places:
• When the cellular phone is obstructed by certain objects (such as when it is behind the
seat or in the glove box and console box).
When the cellular phone touches or is covered with metal materials.
No. Name Function
157
5
Bluetooth® HANDS-FREE SYSTEM
1. BASIC INFORMATION BEFORE OPERATION
2. HANDS-FREE SYSTEM
Bluetooth® hands-free system allows
you to make or receive a call without
taking your hands off the steering
wheel by connecting your cellular
phone.
This system supports Bluetooth®.
Bluetooth® is a wireless data system
by which you can call without your
cellular phone being connected with a
cable or placed on a cradle.
The operating procedure of the system
is explained in this section.
zFor registering and setting of the phone,
see “Bluetooth® SETTINGS” on page
202.
CAUTION
Use a cellular phone or connect the
Bluetooth® phone only when safe and
legal to do so.
NOTICE
Do not leave your cellular phone in the
car. The temperature inside may be high
and damage the phone.
If the Bluetooth® phone is too close to
the system, quality of the sound may
deteriorate and connecting condition
may go down.
INFORMATION
If your cellular phone does not support
Bluetooth®, this system will not function.
Depending on the cellular phone mod-
els, some functions may be restricted.
In the following conditions, the system
may not function.
The cellular phone is turned off.
The current position is outside the
communication area.
The cellular phone is not connected.
• The cellular phone has a low battery.
When outgoing is controlled, due to
heavy traffic on telephone lines, etc.
• When the cellular phone itself cannot
be used
When transferring the phone book
data from the cellular phone
When using Bluetooth® audio and
hands-free at the same time, the follow-
ing problems may occur.
The Bluetooth® connection may be
cut.
Noise may be heard on the
Bluetooth® audio playback.
The Bluetooth® phone battery will burn
out quickly when it is connected to
Bluetooth®.
158
1. BASIC INFORMATION BEFORE OPERATION
Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
zBy pressing the phone, you can receive a
call or hang up without taking your hands
off the steering wheel.
zBy pressing the volume switch, you can
adjust the volume.
zYou can use the microphone when talking
on the phone.
INFORMATION
This system supports the following ser-
vice.
• Bluetooth® Specification
Ver.1.1 or higher
(Recommended: Ver.2.1 + EDR or
higher)
• Profiles
HFP (Hands Free Profile)
Ver.1.0 or higher
(Recommended: Ver.1.5 or higher)
DUN (Dial-Up Networking Profile)
Ver.1.1 or higher
PAN (Personal Area Network)
Ver. 1.0
PBAP (Phone Book Access Profile)
Ver.1.0 or higher
SSP (Serial Port Profile)
MAP (Message Access Profile)
• Application
PIM (Personal Information Manager)
If your cellular phone does not support
HFP, you cannot register the Bluetooth®
phone, or use DUN/PAN or PBAP pro-
files individually.
If the connected Bluetooth® phone ver-
sion is older than recommended or
incompatible, this function may not be
used.
USING THE PHONE SWITCH
The actual design and switch position
may differ depending on the vehicle.
For details, see the Pictorial index of
“Owner’s Manual”.
159
1. BASIC INFORMATION BEFORE OPERATION
5
Bluetooth® HANDS-FREE SYSTEM
zThe following data is stored for every reg-
istered phone. When another phone is
connecting, you cannot read the regis-
tered data.
Phone book data
• Call history data
zYou can initialize the following data in the
system.
Phone book data
• Call history data
Speed dial data
• Bluetooth® phone data
Volume setting
• Bluetooth® setting
INFORMATION
The other party’s voice outputs from the
front speaker. When the received calls
or received voice outputs, the audio
from the audio system will be muted.
Talk alternately with the other party on
the phone. If you talk at the same time,
your voices may not reach each other. (It
is not a malfunction.)
Keep the volume of receiving voice
down. Otherwise, an echo will be heard
and receiving voice can be heard out-
side of the vehicle. When you talk on the
phone, speak clearly towards the micro-
phone.
In the following situations, your voice
may not reach the other party.
Driving on an unpaved road. (Due to
traffic noise.)
Driving at high speed.
A window is open.
Turning the air-conditioning vents
towards the microphone.
The sound of the air-conditioning fan
is loud.
There is an effect from the cellular
phone network.
ABOUT THE PHONE BOOK IN
THIS SYSTEM
INFORMATION
When you delete the phone, the above-
mentioned data is also deleted.
WHEN YOU RELEASE YOUR
CAR
A lot of personal data is registered
when you use the Hands-free system.
When you release your car, initialize
your data. (See “DELETE PERSONAL
DATA” on page 199.)
INFORMATION
If you initialize it, the former state will
never come back again. Pay attention
when initializing the data.
160
1. BASIC INFORMATION BEFORE OPERATION
CAUTION
FCC WARNING: Changes or modifica-
tions not expressly approved by the
party responsible for compliance could
void the user’s authority to operate the
equipment.
CAUTION: Radio Frequency Radiation
Exposure
This equipment complies with FCC radi-
ation exposure limits set forth for uncon-
trolled equipment and meets the FCC
radio frequency (RF) Exposure Guide-
lines in Supplement C to OET65 and
RSS-102 of the IC radio frequency (RF)
Exposure rules. This equipment has
very low levels of RF energy that it
deemed to comply without maximum
permissive exposure evaluation (MPE).
But it is desirable that it should be
installed and operated with at least 20
cm and more between the radiator and
person’s body (excluding extremities:
hands, wrists, feet and ankles).
Co-location: This transmitter must not be
co-located or operated in conjunction
with any other antenna or transmitter.
161
5
Bluetooth® HANDS-FREE SYSTEM
1. BASIC INFORMATION BEFORE OPERATION
3. CONNECTING A Bluetooth® PHONE
CONNECTING FROM THE SYSTEM
1Press the button.
2Touch “Search Bluetooth devices.
3Touch “Search for Bluetooth Devic-
es”.
zWhen a Bluetooth® device is currently
connected, a pop-up window is displayed.
To disconnect it, touch “Yes”.
4The following screen will be displayed
while searching for a Bluetooth® de-
vice.
zTo cancel this function, touch “Cancel.
: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
CONNECTING A Bluetooth®
PHONE
In order to use the hands-free system,
it is necessary to pair the phone and
connect the phone’s profile (HFP) with
the system. (In this manual, pairing re-
fers to a Bluetooth® device connecting
with the system. Connecting refers to
the paired device’s profile(s) being
connected to the system.)
Once the profile has been connected,
hands-free calls can be made.
If you have not yet connected any
Bluetooth® phones with phone profile
(HFP), you must first pair your phone
with phone profile (HFP) according to
the following procedure. Connect your
Bluetooth® phone with phone profile
(HFP) after bringing the vehicle to a
complete stop.
zSee “Bluetooth® SETTINGS” on page
202 of additional registration when reg-
istering.
CONNECTING A Bluetooth®
PHONE
162
1. BASIC INFORMATION BEFORE OPERATION
5Touch the device to be paired.
zConnectable Bluetooth® devices will be
displayed in the list.
6The following screen will be displayed.
zTo cancel this function, touch “Cancel”.
7Confirm the PIN.
XIf the device supports SSP (Secure Sim-
ple Pairing)
zConfirm the PIN displayed on the screen,
and then touch “Accept.
XIf the device does not supports SSP (Se-
cure Simple Pairing)
zInput the PIN displayed on the screen into
the phone.
8The following screen will be displayed
when pairing is complete.
9The system waits for connection re-
quests coming from the paired device.
All requested profiles are connected
automatically.
zIf the automatic connection failed, the fol-
lowing screen will be displayed. Touch
“Connect for Phone”.
zOnce the Bluetooth® phone has been con-
nected, it will be automatically connected
whenever the engine switch is in the
“ACC” or “ON” position.
INFORMATION
For details on device detection and the
operation of your cellular phone, see the
manual that comes with the cellular
phone.
163
1. BASIC INFORMATION BEFORE OPERATION
5
Bluetooth® HANDS-FREE SYSTEM
CONNECTING FROM THE DEVICE
1Press the button.
2Touch “Search Bluetooth devices”.
3Touch “Make Discoverable.
zWhen a Bluetooth® device is currently
connected, a pop-up window is displayed.
To disconnect it, touch “Yes”.
: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
4The following screen will be displayed.
zTo cancel this function, touch “Cancel.
5Confirm the PIN.
XIf the device supports SSP (Secure Sim-
ple Pairing)
zConfirm the PIN displayed on the screen,
and then touch “Accept.
XIf the device does not supports SSP (Se-
cure Simple Pairing)
zInput the PIN displayed on the screen into
the phone.
164
1. BASIC INFORMATION BEFORE OPERATION
zIf the Bluetooth® phone is disconnected
on purpose, such as it was turned off, this
does not happen. Reconnect it manually
using either of the following methods:
Select the Bluetooth® phone again. (See
page 206.)
Connect the phone profile. (See page
203.)
RECONNECTING THE
Bluetooth® PHONE
If a Bluetooth® phone is disconnected
due to poor reception from the
Bluetooth® network when the engine
switch is in the “ACC” or “ON” position,
the system will automatically
reconnect the Bluetooth® phone.
165
5
Bluetooth® HANDS-FREE SYSTEM
1. BASIC INFORMATION BEFORE OPERATION
4. REGISTERING A ENTRY
1Touch “Contacts”.
zThe “Contacts” screen can be displayed
by touching on any of the “Phone
screens.
2Touch “Stored” on the “Contacts
screen.
3Touch “Create New Entry”.
4Select one of 4 phone types (“Mo-
bile”,“Home”,“Work” or “Other”)
and input a number.
: Touch to delete one number. Touch
and hold to continue deleting numbers.
zYou can enter a number for each phone
type.
5Touch .
6Input the entry name.
7Touch “OK”.
8The entry is registered in the “Stored”
list.
REGISTERING A NEW ENTRY
Up to 200 numbers can be registered
with this system.
INFORMATION
This function cannot be operated while
driving.
REGISTERING FROM THE
“Contacts” SCREEN
zTouch to display and edit the entry
information. (See page 168.)
166
1. BASIC INFORMATION BEFORE OPERATION
1Touch “Dial By Number” on the
“Phone” menu screen.
zThe “Dial By Number” screen can be dis-
played by touching on any of the
“Phone” screens.
zYou can also press the switch on the
steering wheel to display the “Dial By
Number” screen.
2Input the numbers.
3Touch .
4Follow the steps “REGISTERING
FROM THE “Contacts” SCREEN” from
“STEP 6”. (See page 165.)
1Search the entry by “Phone Book”.
(See page 171.)
2Touch for desired item.
3Touch “Add to Stored Phone Num-
bers”.
4Follow the steps “REGISTERING
FROM THE “Contacts” SCREEN” from
“STEP 6”. (See page 165.)
1Searching the entry by “Call History”.
(See page 173.)
2Touch next to the desired item.
3Follow the steps “REGISTERING
FROM THE “Contacts” SCREEN” from
“STEP 6”. (See page 165.)
REGISTERING FROM THE “Dial
By Number” SCREEN
INFORMATION
The phone type is registered as
“Mobile”.
REGISTERING FROM THE
“Phone Book” SCREEN
INFORMATION
The phone type is registered as
“Mobile”.
If the contact includes an address and a
phone number, they will be stored in the
“Stored” list on the “My Destinations”
screen and “Contacts” screen. (See
pages 52 and 165.)
REGISTERING FROM THE “Call
History” SCREEN
INFORMATION
The phone type is registered as
“Mobile”.
REGISTERING FROM AN
EXTERNAL DEVICE
“vCard” formatted data can be trans-
ferred from a USB memory to this sys-
tem. Transferred addresses and
numbers will be stored in the “Stored”
list on the “My Destinations” screen
and “Contacts” screen. (See pages 52
and 165.)
167
1. BASIC INFORMATION BEFORE OPERATION
5
Bluetooth® HANDS-FREE SYSTEM
1Touch “Contacts”.
zThe “Contacts” screen can be displayed
by touching on any of the “Phone
screens.
2Touch Speed Dials” on the “Con-
tacts” screen.
3Touch the desired speed dial screen
button the phone number is to be reg-
istered to.
4Touch “Yes”.
5Touch the desired list to select the en-
try.
6Touch the desired entry to register.
zIf there are 2 or more phone numbers,
touch the desired number in the list.
7The entry is registered as “Speed Di-
als”.
REGISTERING A ENTRY AS
“Speed Dials”
Phone numbers from the list in the
“Stored” screen and “Phone Book” can
be registered as speed dials. Up to 15
speed dials can be registered.
zTouch to display and edit the entry
information. (See page 168.)
168
1. BASIC INFORMATION BEFORE OPERATION
1Touch next to the desired entry
on the “Contacts” screen.
XEntry options screen of the “Stored” and
“Speed Dials” list
XEntry options screen of the “Phone
Book” list
zOn this screen, the following functions can
be operated.
1Touch “Rename XX” on the entry op-
tions screen.
2Input the entry name.
3Touch “OK”.
DISPLAYING AND EDITING
THE ENTRY INFORMATION
Detailed information of entries in the
list can be displayed or edited.
No. Function
Touch to display the details of
the entry information.
xTouch the desired entry to call
it.
Touch to change the entry name.
(See page 168.)
Touch to edit phone numbers.
(See page 169.)
Touch to delete the entry.
Touch to delete all entries.
Touch to register the entry in the
“Stored” list on the “My Destina-
tions” screen and “Contacts”
screen. (See page 166.)
INFORMATION
“Rename XX and Edit Phone Num-
bers” cannot be operated while driving.
CHANGING THE ENTRY NAME
169
1. BASIC INFORMATION BEFORE OPERATION
5
Bluetooth® HANDS-FREE SYSTEM
1Touch “Edit Phone Numbers” on the
entry options screen.
2Select one of 4 phone types and input
a number.
: Touch to delete one number. Touch
and hold to continue deleting numbers.
zYou can edit a number for each phone
type.
3Touch .
EDITING PHONE NUMBERS
INFORMATION
If an entry that is transferred from a cel-
lular phone is edited, the change will
affect the entry in the “Stored” list on the
“My Destinations” screen and “Contacts”
screen. (See pages 52 and 165.)
SENDING STORED
CONTACTS TO A USB
MEMORY
The entries stored in the “Stored” list
on the “My Destinations” screen and
“Contacts” screen can be transferred
to a USB memory. (See page 60.)
170
2. TELEPHONE OPERATION
1. CALLING ON A Bluetooth® PHONE
1Press the switch on the steering
wheel.
zThe “Dial By Number” screen can be dis-
played by touching “Dial By Number”
on the “Phone” menu screen or on
any of the “Phone” screens.
2Touch the desired key to input the
phone number.
: Touch to delete one number. Touch
and hold to continue deleting numbers.
3Touch .
4The connecting screen will be dis-
played.
zTo cancel the call, touch “End Call”.
1Touch “Contacts”.
zThe “Contacts” screen can be displayed
by touching on any of the “Phone
screens.
2Touch “Stored” on the “Contacts”
screen.
After a Bluetooth® phone has been
connected, a call can be made using
the hands-free system. There are sev-
eral methods by which a call can be
made. These are described below.
BY DIAL
You can call by inputting the phone
number.
zWhen is touched, the number is
registered in the “Stored” list on the
“Contacts” screen. (See page 166.)
INFORMATION
This function cannot be operated while
driving.
BY “Stored” LIST ON THE
“Contacts” SCREEN
Calls can be made using the “Stored”
list on the “Contacts” screen. To use
this function, it is necessary to register
the entry. (See page 165.)
171
2. TELEPHONE OPERATION
5
Bluetooth® HANDS-FREE SYSTEM
3Touch the desired entry.
zIf there are 2 or more phone numbers,
touch the desired number in the list.
4The connecting screen will be dis-
played.
zTo cancel the call, touch “End Call”.
1Touch “Contacts”.
zThe “Contacts” screen can be displayed
by touching on any of the “Phone”
screens.
2Touch “Phone Book” on the “Con-
tacts” screen.
3Touch the desired entry.
zIf there are 2 or more phone numbers,
touch the desired number in the list.
zTouch to display and edit the entry
information. (See page 168.)
BY PHONE BOOK
Calls can be made using the phone
book data of the connected cellular
phone. The phone book changes de-
pending on the phone connected.
If a contact does not have phone num-
ber stored, the entry will be dimmed.
You can update the Phone’s book list.
(See page 209.)
172
2. TELEPHONE OPERATION
4The connecting screen will be dis-
played.
zTo cancel the call, touch “End Call”.
1Touch “Contacts”.
zThe “Contacts” screen can be displayed
by touching on any of the “Phone
screens.
2Touch “Speed Dials” on the “Con-
tacts” screen.
3Touch the desired entry.
4The connecting screen will be dis-
played.
zTo cancel the call, touch “End Call”.
zTouch “Search Contact” to search by
the contact’s name. This function cannot
be operated while driving.
zTouch to display and edit the entry
information. (See page 168.)
INFORMATION
When a phone is connected for the first
time, its phone book must be down-
loaded. If the phone book can not be
downloaded, a pop-up window will be
displayed.
BY SPEED DIALS
You can call by “Speed Dial” number
list. Registering number in the “Speed
Dial” number list is to see page 167.
zTouch to display and edit the entry
information. (See page 168.)
173
2. TELEPHONE OPERATION
5
Bluetooth® HANDS-FREE SYSTEM
1Touch “Call History”.
zThe “Call History” screen can be displayed
by touching on any of the “Phone
screens.
2Touch the desired list.
“All”: Touch to display all numbers
(missed, received and dialed).
“Missed”: Touch to display missed
calls.
“Received”: Touch to display received
calls.
“Dialed”: Touch to display dialed num-
bers.
zThe state of a call is shown by the follow-
ing icons.
: Missed
: Received
: Dialed
3Touch the desired entry.
4The connecting screen will be dis-
played.
zTo cancel the call, touch “End Call”.
1Touch “Call Sender”.
2The connecting screen will be dis-
played.
zTo cancel the call, touch “End Call”.
BY CALL HISTORY
Calls can be made using one of the 4
call lists functions.
zWhen is touched, the entry is reg-
istered in the “Stored” list on the “Con-
tacts” screen. (See page 166.)
CALLING USING A SHORT
MESSAGE
Calls can be made to a short message
sender’s phone number. (See page
179.)
174
2. TELEPHONE OPERATION
1Touch .
2The connecting screen will be dis-
played.
zTo cancel the call, touch “End Call”.
BY POI CALL
Calls can be made to a POI when its
details are displayed on the screen.
(See pages 32 and 36.)
175
5
Bluetooth® HANDS-FREE SYSTEM
2. TELEPHONE OPERATION
2. RECEIVING CALLS ON A Bluetooth® PHONE
1Press the switch on the steering
wheel.
“Accept”: Touch to talk on the phone.
“Reject”: Touch to reject the call.
zThe layout of the incoming call screen
may differ depending on the information
available from the connected phone.
XSingle call
2The ongoing screen is displayed. (See
page 176.)
XCall waiting
2The ongoing screen is displayed. (See
page 176.)
zThe first call is put on hold.
zThe second call’s information is displayed
below the first call information.
When a call is received, this screen is
displayed and a sound is heard.
zRingtone and ringtone volume can be
set. (See pages 197 and 209.)
INFORMATION
During international phone calls, the
other partys name may not be displayed
correctly depending on the cellular
phone which you have.
176
2. TELEPHONE OPERATION
3. TALKING ON A Bluetooth® PHONE
XSingle call
XCall waiting
zOn this screen, the following functions can
be operated.
While you are talking on a Bluetooth®
phone, the ongoing screen is dis-
played. The operations outlined below
can be performed on this screen.
NO. Function
Touch to hang up the phone.
xThe switch on the steering
wheel can also be pressed to
hang up the phone.
Touch to dial a second number.
(See page 177.)
Touch to send a tone. (See page
177.)
Touch to put a call on hold. To
cancel this function, touch “Ac-
tive call”.
Touch to mute your voice. To
cancel muting your voice, touch
“Unmute call”.
Touch to transfer the call. Touch
“Transfer to Phone to change
from Hands-free call to cellular
phone call. Touch “Handsfree
mode” to change from cellular
phone call to Hands-free call.
Displays a call duration.
Touch to adjust the volume of the
other party’s voice. (See page
177.)
Displays the name, number and
picture of the other party. The in-
formation shown here may differ
depending on the information
available from your phone.
Touch to change parties.
Touch to change to a conference
call.
INFORMATION
When you change from cellular phone
call to Hands-free call, the Hands-free
screen will be displayed and the call can
be operated on the screen.
Transferring methods will be different
depending on the type of cellular phone
which you have.
For the operation of the phone, see the
manual that comes with your cellular
phone.
NO. Function
177
2. TELEPHONE OPERATION
5
Bluetooth® HANDS-FREE SYSTEM
1Touch .
2Touch “-” or “+” to adjust the volume
of the other party’s voice.
1Touch “Dial Pad.
2Inputting the numbers.
zInput numbers are sent immediately as
tones.
zTouch “Quit” to return the previous
screen.
1Touch “Dial”.
2Touch the desired method to call.
XIf “Dial Number is selected
3Input the number and then touch .
XIf “Dial From Contacts” is selected
3Touch the desired method and then
touch the desired entry.
ADJUSTING THE RECEIVER
VOLUME
zThe receiver volume can also be
adjusted using the switch on the steer-
ing wheel.
SENDING TONES
DIALING A SECOND NUMBER
178
2. TELEPHONE OPERATION
XIf “Dial From Call History” is selected
3Touch the desired list and then touch
the desired entry.
4The connecting screen will be dis-
played.
zTo cancel the call, touch “End Call”.
5When a new call has been established,
the following screen will be displayed.
zThe first call is put on hold.
zThe second call’s information is displayed
below the first call information.
CHANGING PARTIES
1Touch “Swap Calls”.
zEvery time “Swap Calls” is touched, the
party who is on hold will be switched.
CHANGING TO A CONFERENCE
CALL
1Touch “Link Calls”.
INFORMATION
“Dial Number” cannot be operated
while driving.
INFORMATION
If your cellular phone is not HFP Ver. 1.5
compatible, this function can not be
used.
Dialing a second number operation may
differ depending on your phone com-
pany and cellular phone.
179
5
Bluetooth® HANDS-FREE SYSTEM
3. SHORT MESSAGE FUNCTION
1. SHORT MESSAGE FUNCTION
1Touch “Messages”.
zThe “Messages” screen can be displayed
by touching on any of the “Phone
screens.
2Touch “Inbox on the “Messages
screen.
3Touch the desired short message.
zThe state of a message is shown by the
following icons.
: New message
: Read message
: Unread message
4The short message will be displayed.
zOn this screen, the following functions can
be operated.
Received messages can be forwarded
from the connected Bluetooth® phone,
enabling checking and replying using
this system.
RECEIVING A NEW SHORT
MESSAGE
When a new short message is re-
ceived, a pop-up window is displayed
on the screen.
zThis function can be set to “On” or
“Off”. (See page 209.)
CHECKING RECEIVED
SHORT MESSAGES
No. Function
Touch to have the short
message read out. To cancel this
function, touch .
Touch to call the sender.
Touch to reply to the short mes-
sage by free text.
Touch to reply to the short mes-
sage by template.
180
3. SHORT MESSAGE FUNCTION
1Touch “Reply Free Text” or “Reply
Template.
2Input the short message.
3Touch “OK”.
4The short message will be sent.
1Touch “Messages” on the “Phone”
menu screen.
zThe “Messages” screen can be displayed
by touching on any of the “Phone”
screens.
2Touch “Sent” on the “Messages”
screen.
3Touch the desired short message.
4The short message will be displayed.
: Touch to have the short message
read out. To cancel this function, touch
.
1Touch “Messages” on the “Phone”
menu screen.
zThe “Messages” screen can be displayed
by touching on any of the “Phone
screens.
2Touch “Create New” on the “Messag-
es” screen.
3Touch “Create Message” or “Use
Template.
REPLYING THE SHORT
MESSAGE
INFORMATION
“Reply Free Text” cannot be selected
while driving.
CHECKING SENT SHORT
MESSAGES
SENDING A NEW SHORT
MESSAGES
181
3. SHORT MESSAGE FUNCTION
5
Bluetooth® HANDS-FREE SYSTEM
4Input the short message. (See page
182.)
5Touch “OK.
6Select the desired number/contact to
whom the short message should be
sent.
z“Enter Number,“Select Contact and
a list of former recipients will be displayed.
XIf “Enter Number” is selected
7Enter the number.
8Touch “OK.
9The short message will be sent.
XIf “Select Contact” is selected
7Touch the desired list.
8Touch the desired contact.
9The short message will be sent.
XIf a recipient is selected
7The short message will be sent imme-
diately.
INFORMATION
“Create Message” cannot be selected
while driving.
182
3. SHORT MESSAGE FUNCTION
FROM THE “Create Message”
SCREEN
1Input the short message.
2Touch “OK”.
FROM THE “Use Template”
SCREEN
1Touch the desired template.
: Touch to delete the template.
z10 messages have already been regis-
tered to the message template screen.
2Edit the short message.
zThis screen is not displayed while driving.
When a template is touched, the screen
will be changed to the recipient selection
screen.
3Touch “OK”.
CREATE A NEW SHORT
MESSAGE
INFORMATION
The cursor’s position can be moved by
touching the desired location in the input
screen. Touch or to scroll the
input screen up or down.
The short messages can contain up to
160 characters. If the entered text
exceeds the characters available for one
short message, a new short message
will begin automatically. This is indicated
by a separation line and an icon in the
input field, which is shown as soon as
there are only 10 characters left for the
short message.
The number of characters left for the
short message is displayed.
A maximum of 6 short messages can be
written in series.
183
3. SHORT MESSAGE FUNCTION
5
Bluetooth® HANDS-FREE SYSTEM
1Touch “Prepare Template Message”.
2Input the short message.
3Touch “OK.
4The message is registered in the tem-
plate list on the “Use Template
screen.
REGISTER NEW TEMPLATES
New templates can be created. Up to
15 templates can be registered.
INFORMATION
This function is unavailable while driv-
ing.
184
3. SHORT MESSAGE FUNCTION
6
185
1
2
3
4
6
7
8
9
1. VOICE COMMAND SYSTEM...... 186
USING THE VOICE COMMAND
SYSTEM............................................ 186
VOICE COMMAND SYSTEM
OPERATION ..................................... 187
1VOICE COMMAND SYSTEM
OPERATION
VOICE COMMAND SYSTEM
186
1. VOICE COMMAND SYSTEM OPERATION
1. VOICE COMMAND SYSTEM
XType A (Two direction steering switch)
XType B (Four direction steering switch)
Talk switch
zPress the talk switch to start the voice
command system.
zPress and hold the talk switch to cancel
the voice command system.
Back switch
zPress the back switch to return to the pre-
vious screen.
The voice command system enables
the navigation, audio and hands-free
systems to be operated using voice
commands.
INFORMATION
Voice recognition language can be
changed.(See “SELECTING A LAN-
GUAGE” on page 198)
USING THE VOICE
COMMAND SYSTEM
The actual design and switch position
may differ depending on the vehicle.
For details, see the Pictorial index of
“Owner’s Manual”.
STEERING SWITCHES FOR
THE VOICE COMMAND
SYSTEM
MICROPHONE
It is unnecessary to speak directly into
the microphone when giving a com-
mand.
187
1. VOICE COMMAND SYSTEM OPERATION
6
VOICE COMMAND SYSTEM
1Press the talk switch.
2After a beep sounds, say the desired
command or touch the desired com-
mand.
: The icon will be displayed if the user
can speak a command.
: Touch to adjust the volume of the
voice guidance volume.
INFORMATION
Wait for the confirmation beep before
speaking a command.
Voice commands may not be recognized
if:
Spoken too quickly.
Spoken at a low or high volume.
The windows are open.
Passengers are talking while voice
commands are spoken.
The air conditioning speed is set high.
The air conditioning vents are turned
towards the microphone.
In the following conditions, the system
may not recognize the command prop-
erly and using voice commands may not
be possible:
The command is incorrect or unclear.
Note that certain words, accents or
speech patterns may be difficult for the
system to recognize.
There is excessive background noise,
such as wind noise.
VOICE COMMAND SYSTEM
OPERATION
zThe voice command system is acti-
vated, press the talk switch to skip the
current dialog state.
zIn case of an activated speech recog-
nizer waiting for input, press the talk
switch to restart the speech recognizer.
188
1. VOICE COMMAND SYSTEM OPERATION
DISPLAYING THE COMMAND LIST
SCREEN
1Say “More commands or touching
“More commands” on the voice com-
mand main menu screen.
2Say the desired command or touch the
desired command.
3Say the desired command or touch the
desired command.
zThe command list is read out and the cor-
responding command is highlighted. To
cancel this function, press the talk switch.
7
189
1
2
3
4
5
6
7
8
9
1. QUICK REFERENCE .................. 190
2. FUEL CONSUMPTION................ 191
FUEL CONSUMPTION
(VEHICLES WITH HYBRID
SYSTEM) .......................................... 191
FUEL CONSUMPTION
(VEHICLES WITH GASOLINE
ENGINE) ........................................... 191
3. TIRE PRESSURE WARNING
SYSTEM.................................... 193
SHOWING THE TIRE PRESSURE
SCREEN ........................................... 193
1VEHICLE INFORMATION
VEHICLE INFORMATION
190
1. VEHICLE INFORMATION
1. QUICK REFERENCE
zThe actual design and button position may differ depending on the vehicle. For
details, see Section 3 of “Owner’s Manual”.
zThe “Information” screen shown above is displayed if the vehicle is equipped with
both a fuel consumption and a tire pressure warning system.
*: If equipped
Fuel consumption information and tire pressure value can be displayed. To access
the vehicle information system, press the “CAR button.
No. Name Function Page
“Fuel Consumption”* Displays the “Trip Information”, “History” and
“Energy Monitor” screen. 191
“Tire Pressure”* Displays the “Tire Pressure” screen. 193
“CAR” button* Press this button to access the vehicle information
system.
191
7
VEHICLE INFORMATION
1. VEHICLE INFORMATION
2. FUEL CONSUMPTION
zEnergy monitor
zTrip consumption
zHistory
1Press the “CAR” button.
2Touch “Fuel Consumption”.
z“Trip Information” or “History” screen will
be displayed.
zThe “Information” screen is not displayed
if the vehicles not equipped with a tire
pressure warning system.
zIf the “Trip Information” screen is not dis-
played, touch “Trip Information.
“Clear: Trip information data can be de-
lete by touching this screen button.
“History”: “History” screen can be dis-
played by touching this screen button.
FUEL CONSUMPTION
(VEHICLES WITH HYBRID
SYSTEM)
Fuel consumption such as shown be-
low can be displayed on the screen.
For details see Section 1-1 of “Owner’s
Manual”.
FUEL CONSUMPTION
(VEHICLES WITH GASOLINE
ENGINE)
: If equipped
TRIP INFORMATION
No. Name
Average speed
Elapsed time
Cruising range
Previous fuel consumption per
minute
Current fuel consumption per
minute
INFORMATION
The trip information display indicates
general driving conditions. Accuracy
varies with driving habits and road con-
ditions.
192
1. VEHICLE INFORMATION
zIf the “History” screen is not displayed,
touch “History”.
zThe average fuel consumption history is
divided by color into past averages and
the average fuel consumption since the
last reset.
“Clear: Past record data can be delete by
touching this screen button.
“Update”: Reset the average fuel con-
sumption to measure the current fuel con-
sumption again.
XVehicle with multi-information display
When you touch “Update”, the average
fuel consumption displayed in the multi-in-
formation display will be reset at the same
time.
“Trip Information”: “Trip Information”
screen can be displayed by touching this
screen button.
HISTORY
No. Name
Previous fuel economy record
Current fuel economy
Best recorded fuel economy
193
7
VEHICLE INFORMATION
1. VEHICLE INFORMATION
3. TIRE PRESSURE WARNING SYSTEM
zTo confirm tire pressure values,
touch “Yes. To cancel and return
to the previous screen, touch
“No”. (This screen will not be
shown if the tire pressure screen
is already being displayed.)
1Press the “CAR” button.
2Touch “Tire Pressure”.
3The tire pressure value of each
tire will be displayed.
XType A
XType B
zLow tire pressure values will be
displayed in orange.
zThe display pattern varies
depending on the vehicle. Some
vehicles do not show the spare
tire pressure.
Vehicles equipped with a tire pres-
sure warning system will display a
warning screen in addition to a
warning indication on the meter if
tire pressure becomes low. For in-
formation on the tire pressure
warning system, refer to “Owner’s
Manual.
SHOWING THE TIRE
PRESSURE SCREEN
The tire pressure value of each tire
can be confirmed using the tire
pressure screen.
: If equipped
194
1. VEHICLE INFORMATION
8
195
1
2
3
4
5
6
7
8
9
1. QUICK REFERENCE .................. 196
2. GENERAL SETTINGS ................ 197
SCREENS FOR GENERAL
SETTINGS ........................................ 197
3. DISPLAY SETTINGS .................. 200
TURN OFF DISPLAY........................... 200
CHANGING BETWEEN DAY AND
NIGHT MODE ................................... 201
ADJUST CONTRAST/
BRIGHTNESS ................................... 201
4. Bluetooth® SETTINGS ............... 202
Bluetooth® FUNCTION ON/OFF.......... 202
PAIRING A Bluetooth® DEVICE .......... 203
DISPLAYING THE PAIRED
DEVICE LIST .................................... 206
SETTING PIN ...................................... 207
SETTING THE INTERNET
CONNECTION .................................. 208
5. PHONE SETTINGS ..................... 209
SCREEN FOR PHONE SETTINGS..... 209
6. AUDIO SETTINGS ...................... 210
7. VEHICLE SETTINGS .................. 211
1SETUP OPERATION
SETUP
196
1. SETUP OPERATION
1. QUICK REFERENCE
zThe actual design and button position may differ depending on the vehicle. For
details, see Section 3 of “Owner’s Manual”.
*: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
To customize the function settings, press the “SETUP” button.
No. Name Function Page
“General” Settings are available for language selection,
operation sounds, etc. 197
“Bluetooth*”
Registering, removing, connecting and discon-
necting Bluetooth® devices and settings are
available for Bluetooth®.
202
“Display” Settings are available for contrast and bright-
ness of the screen. 200
“Phone” Settings are available for phone sound, phone
book, etc. 209
“SETUP” button Press this button to display the “Setup” screen. 197, 200, 202,
209, 210, 211
“Vehicle” Settings are available for vehicle customization. 211
“Audio” Settings are available for HD Radio™ system. 210
197
8
SETUP
1. SETUP OPERATION
2. GENERAL SETTINGS
1Press the SETUP” button.
2Touch “General”.
3Touch the items to be set.
4Touch “Save”.
zOn this screen, the following functions are
operational.
Settings are available for language se-
lection, operation sounds, etc. SCREENS FOR GENERAL
SETTINGS
No. Function
You can change the language.
(See “SELECTING A
LANGUAGE” on page 198.)
“On” or “Off” can be selected to
sound beeps.
The personal data can be delet-
ed. (See “DELETE PERSONAL
DATA” on page 199.)
Touch to set the distance unit to
“Kilometer” or “Mile”.
198
1. SETUP OPERATION
1Press the “SETUP” button.
2Touch “General” on the “Setup
screen.
3Touch “Language”.
4Touch the desired screen button.
zThe previous screen will be displayed.
zThe selectable languages may differ
depending on the model or region.
5Touch “Save”.
Touch to change a keyboard lay-
out. (See “SELECTING A KEY-
BOARD LAYOUT” on page 199.)
Touch to set the navigation
prompt volume.
Touch to set the phone volume.
Touch to set the ringtone vol-
ume.
Touch to set the voice dialog vol-
ume.
The entries stored in the “Stored”
list on the “My Destinations”
screen and “Contacts” screen
(See pages 52 and 165.) can be
transferred to a USB memory.
(See “SENDING STORED CON-
TACTS TO A USB MEMORY” on
page 60.)
“vCard” formatted data can be
transferred from a USB memory
to this system. Transferred ad-
dresses and numbers will be
stored in the “Stored” list on the
“My Destinations” screen and
“Contacts” screen. (See “LOAD-
ING ADDRESSES VIA A USB
MEMORY” on page 56.)
Touch to select on or off for day-
light saving time.
Touch to display the system in-
formation.
No. Function SELECTING A LANGUAGE
The desired language can be selected.
199
1. SETUP OPERATION
8
SETUP
1Press the SETUP” button.
2Touch “General” on the “Setup”
screen.
3Touch “Delete Personal Data”.
4Touch “Delete”.
1Press the “SETUP” button.
2Touch “General on the “Setup”
screen
3Touch “Keyboard Layout”.
4Touch the desired keyboard layout.
“QWERTY”: Latin characters, “QWER-
TY”-Layout
“ABC”: Latin characters, “ABC”-Layout
DELETE PERSONAL DATA
INFORMATION
The following personal data can be
deleted or returned to their default set-
tings:
Phone book data
Call history data
Speed dial data
• Bluetooth® devices data
Phone sound setting
• Bluetooth® setting
Sound setting
SELECTING A KEYBOARD
LAYOUT
200
1. SETUP OPERATION
3. DISPLAY SETTINGS
1Press the “SETUP” button.
2Touch “Display”.
3Touch the items to be set.
zPlease refer to the following pages for
each setting.
1Press the “SETUP” button.
2Touch “Display” on the “Setup”
screen.
3Touch “Screen Off”.
zThe display screen will be turned off. To
turn it on, press the “AUDIO”,“CAR” or
“SETUP” button.
You can adjust the contrast and bright-
ness of the screen. You can also turn
the display off.
TURN OFF DISPLAY
201
1. SETUP OPERATION
8
SETUP
1To display the screen in day mode
even with the headlight switch on,
touch “Day Mode” on the adjustment
screen for brightness and contrast con-
trol.
1Press the “SETUP” button.
2Touch “Display” on the “Setup”
screen.
3Touch “General or “Camera”, in
which you want to make an adjust-
ment.
4Select “Contrast” or “Brightness”
using the or .
5Adjust the contrast or brightness using
the “+ or “-”.
6After adjusting the screen, touch
“OK”.
CHANGING BETWEEN DAY
AND NIGHT MODE
Depending on the position of the head-
light switch, the screen changes to day
or night mode.
INFORMATION
If the screen is set in day mode with the
headlight switch turned on, this condition
is memorized even with the engine
turned off.
ADJUST CONTRAST/
BRIGHTNESS
Screen button Function
“Contrast” “+” Strengthens the contrast
of the screen
“Contrast” “-” Weakens the contrast of
the screen
“Brightness” “+” Brightens the screen
“Brightness” “- Darkens the screen
202
1. SETUP OPERATION
4. Bluetooth® SETTINGS
1Press the “SETUP” button.
2Touch “Bluetooth.
3The following screen will be displayed.
zPlease refer to the following pages for a
description of each setting.
1Touch “Bluetooth.
2Touch “On” or “Off”.
: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
To set up a Bluetooth® device. Bluetooth® FUNCTION ON/
OFF
The Bluetooth® function can be
switched on or off.
INFORMATION
When Bluetooth® function is off,
“Search for Bluetooth Devices”,
“Make Discoverable”,“Paired Device
List”,Set PIN for Pairing” and “Inter-
net Connection” will be dimmed.
203
1. SETUP OPERATION
8
SETUP
1Touch “Search for Bluetooth Devic-
es”.
zWhen a Bluetooth® device is currently
connected, a pop-up window is displayed.
To disconnect it, touch “Yes”.
2The following screen will be displayed
while searching for a Bluetooth® de-
vice.
zTo cancel this function, touch “Cancel”.
: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
3Touch the device to be paired.
zConnectable Bluetooth® devices will be
displayed in the list.
4The following screen will be displayed.
zTo cancel this function, touch “Cancel.
5Confirm the PIN.
XIf the device supports SSP (Secure Sim-
ple Pairing)
zConfirm the PIN displayed on the screen,
and then touch “Accept.
XIf the device does not supports SSP (Se-
cure Simple Pairing)
zInput the PIN displayed on the screen into
the device.
6The following screen will be displayed
when pairing is complete.
PAIRING A Bluetooth®
DEVICE
Up to 4 Bluetooth® devices can be
paired. A paired device can be con-
nected to any of its supported profiles
such as phone, music and/or internet.
CONNECTING FROM THE
SYSTEM
204
1. SETUP OPERATION
7The system waits for connection re-
quests coming from the paired device.
All requested profiles are connected
automatically.
zInternet profile is not connected automati-
cally. For details on connecting internet
profile, see “LOGIN PROCESS INTER-
NET PROFILE” on page 205.
zIf the automatic connection failed, the fol-
lowing screen will be displayed. Touch the
desired profile to be connected.
“Connect for Phone”: Touch to connect
the phone profile.
“Connect for Music”: Touch to connect
the music profile.
“Connect for Internet”,“Advanced”:
Touch to connect the internet profile. The
screen will be changed to the login pro-
cess. (See page 205.)
“Connect All”: Touch to connect all sup-
ported profiles.
zOnce you have connected the Bluetooth®
device, it is automatically connected
whenever the engine switch is in the
“ACC” or “ON” position.
INFORMATION
For details on device detection and the
operation of your Bluetooth® device, see
the manual that comes with the
Bluetooth® device.
The music profiles the paired device
supports can be connected individually
as desired. Some devices do not allow
individual profiles to be connected. In
that case, a pop-up window is displayed.
205
1. SETUP OPERATION
8
SETUP
1Touch “Make Discoverable.
zWhen a Bluetooth® device is currently
connected, a pop-up window is displayed.
To disconnect it, touch “Yes”.
2The following screen will be displayed.
zTo cancel this function, touch “Cancel”.
3Confirm the PIN.
XIf the device supports SSP (Secure Sim-
ple Pairing)
zConfirm the PIN displayed on the screen,
and then touch “Accept”.
XIf the device does not supports SSP (Se-
cure Simple Pairing)
zInput the PIN displayed on the screen into
the device.
XIf “Connect for Internet” is selected
1Touch “Connect for Internet”.
2Touch the desired provider.
zThis screen is displayed only when mak-
ing the first connection.
XIf “Advanced” is selected.
1Touch “Advanced”.
CONNECTING FROM THE
DEVICE
LOGIN PROCESS INTERNET
PROFILE
206
1. SETUP OPERATION
2Touch “Confirm Provider Informa-
tion”.
zUser login information can be changed on
this screen.
1Touch “Paired Device List”.
2Touch the desired device.
zThe tone of the icons show which profiles
the device supports. (Dimmed icons are
not available.)
zThe device’s currently connected profiles
are highlighted.
3The following screen will be displayed.
zOn this screen, the following functions can
be operated.
INFORMATION
When making the first connection,
“Advanced” is not displayed.
When Remember User Login Infor-
mation” function is on, the entered user
login information will be remembered for
every login. (See page 208.)
DISPLAYING THE PAIRED
DEVICE LIST
Devices can be disconnected and
each profile connection status can be
changed using the list.
Up to 4 devices can be paired at the
same time.
207
1. SETUP OPERATION
8
SETUP
1Touch “Rename XX”.
2Input the device name.
3Touch “OK.
1Touch “Delete Pairing”.
2Touch “Yes”.
1Touch the desired profile to be con-
nected or disconnected.
“Connect All”: Touch to connect all sup-
ported profiles.
“Disconnect All”: Touch to disconnect all
supported profiles.
1Touch “Set PIN for Pairing.
2Input the desired number.
zA 4 to 8-digit PIN can be selected.
3Touch “OK”.
CHANGING THE DEVICE NAME
DELETING A PAIRED DEVICE
CONNECTING OR
DISCONNECTING PROFILES
SETTING PIN
To change the PIN.
208
1. SETUP OPERATION
1Touch “Internet Connection”.
2Touch the desired items to be set.
zOn this screen, the following functions can
be set.
SETTING THE INTERNET
CONNECTION
To change the internet settings.
No. Function
Touch to turn the automatic
download of addresses function
on or off.
Touch to turn the show cost
warning function on or off.
When this function is activated, a
pop-up window will be displayed
before using Entune service.
Touch to turn the show roaming
warning function on or off. When
this function is activated, a pop-
up window will be displayed be-
fore using Entune service.
Touch to turn the remember user
login information function on or
off.
When this function is activated,
the entered user login informa-
tion will be remembered for every
user login.
Touch to turn the automatic syn-
chronization function on or off.
INFORMATION
If “Automatic Download of
Addresses” is activated, “Show Cost
Warning and “Show Roaming Warn-
ing” will be dimmed.
209
8
SETUP
1. SETUP OPERATION
5. PHONE SETTINGS
1Press the SETUP” button.
2Touch “Phone”.
3Touch the desired items to be set.
zOn this screen, the following functions can
be set.
Settings are available for ringtone se-
lection, announce incoming short mes-
sage and email, and “Stored” lists.
SCREEN FOR PHONE
SETTINGS
No. Function
Touch to select a ringtone. No
ringtone, the phone’s ringtone
and the system’s 4 ringtones are
available for selection.
Touch to turn the incoming short
message announcement func-
tion “On” or “Off”.
Touch to turn the incoming Email
announcement function “On or
“Off”.
Touch to update the phone book
of the connected phone. The up-
dated list refers to the “Stored”
list on the “My Destinations”
screen and “Contacts” screen.
(See pages 52 and 165.)
210
1. SETUP OPERATION
6. AUDIO SETTINGS
1Press the “SETUP” button.
2Touch “Audio.
3Touch “HD Radio Settings”.
4Select the desired setting from “HD
Radio/Analog Setting”.
5Touch “Save”.
HD Radio™ system can be set using
the following procedure:
Screen button Function
“All”
Touch to receive both an-
alog and digital broad-
casts.
“HD Only” Touch to receive only digi-
tal broadcasts.
“Analog” Touch to receive only ana-
log broadcasts.
211
8
SETUP
1. SETUP OPERATION
7. VEHICLE SETTINGS
1Press the SETUP” button.
2Touch “Vehicle”.
3Touch the desired items to be set.
zFor a list of the settings that can be
changed, see “Owners Manual”.
4After changing the settings, touch
“Save”.
zA message indicating that the settings are
being saved will appear. Do not perform
any other operations while this message is
displayed.
Vehicle customization settings can be
changed.
: If equipped
212
1. SETUP OPERATION
9
213
1
2
3
4
5
6
7
8
9
1. REAR VIEW MONITOR
SYSTEM OPERATION.............. 214
REAR VIEW MONITOR GUIDE
LINES................................................ 215
AREA DISPLAYED ON SCREEN........ 216
THE REAR VIEW MONITOR SYSTEM
CAMERA ........................................... 216
2. DRIVING PRECAUTIONS
(WITH REAR VIEW MONITOR
GUIDE LINES)........................... 218
1REAR VIEW MONITOR
SYSTEM
REAR VIEW MONITOR SYSTEM
214
1. REAR VIEW MONITOR SYSTEM
1. REAR VIEW MONITOR SYSTEM OPERATION
1To display the rear view image on the
screen, the shift lever is in the “R” posi-
tion when the engine switch is in the
“ON” position.
zIf you move the shift lever out of the “R”
position, the screen returns to the previ-
ous screen.
The rear view monitor system assists
the driver by displaying an image of the
view behind the vehicle while backing
up.
The image is displayed in reverse on
the screen. This allows the image to
appear in the same manner as that of
the rear view mirror.
CAUTION
Never depend on the rear view monitor
system entirely when backing up.
Always make sure your intended path is
clear.
Use caution, just as you would when
backing up any vehicle.
Never back up while looking only at the
screen. The image on the screen is dif-
ferent from actual conditions. Depicted
distances between objects and flat sur-
faces will differ from the actual dis-
tances. If you back up while looking only
at the screen, you may hit a vehicle, a
person or an object. When backing up,
be sure to check behind and all around
the vehicle visually and with mirrors
before proceeding.
Do not use the system when the back
door, trunk or tailgate is not completely
closed.
Use your own eyes to confirm the vehi-
cle’s surroundings, as the displayed
image may become faint or dark, and
moving images will be distorted, or not
entirely visible when the outside temper-
ature is low. When backing up, be sure
to check behind and all around the vehi-
cle visually and with mirror before pro-
ceeding.
Do not use the system in the following
cases:
On icy or slick road surfaces, or in
snow.
When using tire chains or emergency
tires.
On an uneven road, such as a slope.
XWith rear view monitor guide lines (If
equipped)
Always check the vehicle surrounding
area, because the guide lines are ancil-
lary lines.
The guide lines are ancillary lines and
do not change even if the steering wheel
is turned.
215
1. REAR VIEW MONITOR SYSTEM
9
REAR VIEW MONITOR SYSTEM
zGuidelines shown differ from those shown
on the actual screen.
Vehicle width extension guide lines
(blue)
zThese lines indicate the estimated vehicle
width extension.
Distance guide line (blue)
zThis line indicates a position on the
ground about 3 ft. (1 m) behind on the
ground of the rear bumper of the vehicle.
Distance guide line (red)
zThis line indicates a position on the
ground about 1.5 ft. (0.5 m) behind on the
ground of the rear bumper of the vehicle.
Vehicle center guide lines (blue)
zThese lines indicate the estimated vehicle
center on the ground.
NOTICE
If the back of the vehicle is hit, the posi-
tion and mounting angle of the camera
may change. Be sure to have the cam-
era’s position and mounting angle
checked at your Toyota dealer.
As the camera has a water proof con-
struction, do not detach, disassemble or
modify it. This may cause incorrect oper-
ation.
If the temperature changes rapidly, such
as when hot water is poured on the vehi-
cle in cold weather, the system may not
operate normally.
Do not strongly rub the camera lens. If
the camera lens is scratched, it can not
transmit a clear image.
Do not allow organic solvent, car wax,
window cleaner or glass coat to adhere
to the camera. If this happens, wipe it off
as soon as possible.
If the tire size is changed, the area dis-
played on the screen may change.
When washing the vehicle, do not apply
intensive bursts of water to the camera
or camera area. Doing so may result in
the camera malfunctioning.
INFORMATION
If the camera lens becomes dirty, it can-
not transmit a clear image. If water drop-
lets, snow, or mud adhere to the lens,
rinse with water and wipe with a soft
cloth. If the lens is extremely dirty, wash
it with a mild cleanser and rinse.
REAR VIEW MONITOR GUIDE
LINES (IF EQUIPPED)
Guide lines are displayed on the
screen.
216
1. REAR VIEW MONITOR SYSTEM
zThe actual camera location may differ
depending on the vehicle. For details, see
the Pictorial index of “Owner’s Manual.
AREA DISPLAYED ON
SCREEN
Image is displayed approximately level
on screen.
INFORMATION
The area detected by the camera is lim-
ited. The camera does not detect
objects which are close to either corner
of the bumper or under the bumper.
Corners of bumper
INFORMATION
The area displayed on the screen may
vary according to vehicle orientation or
road conditions.
THE REAR VIEW MONITOR
SYSTEM CAMERA
The rear view monitor system camera
is located as shown in the illustration.
217
1. REAR VIEW MONITOR SYSTEM
9
REAR VIEW MONITOR SYSTEM
XOn some models
If a bright light (for example, sunlight re-
flected off the vehicle body) is picked up by
the camera, the smear effect* peculiar to
the camera may occur.
*: Smear effect A phenomenon that oc-
curs when a bright light (for example, sun-
light reflected off the vehicle body) is
picked up by the camera; when transmit-
ted by the camera, the light source ap-
pears to have a vertical streak above and
below it.
INFORMATION
The camera uses a special lens. The
distance of the image that appears on
the screen differs from the actual dis-
tance.
In the following cases, it may become
difficult to see the images on the screen,
even when the system is functioning.
In the dark (for example, at night)
When the temperature near the lens
is high or low
When water droplets are adhering to
the camera, or when humidity is high
(for example, when it rains)
When foreign matter (for example,
snow or mud) is adhering to the cam-
era
When the camera has scratches or
dirt on it
When the sun or the beam of head-
lights is shining directly into the cam-
era lens
When the camera is used under fluores-
cent lights, sodium lights, or mercury
lights etc., the lights and the illuminated
areas may appear to flicker.
218
1. REAR VIEW MONITOR SYSTEM
2. DRIVING PRECAUTIONS (WITH REAR VIEW MONITOR GUIDE LINES)
zWhen the grade behind the vehicle slopes
up sharply, objects appear to be farther
away than they actually are.
zWhen the grade behind the vehicle slopes
down sharply, objects appear to be closer
than they actually are.
zWhen any part of the vehicle sags due to
the number of passengers or the distribu-
tion of the load, there is a margin of error
between the guide lines on the screen and
the actual distance/course on the road.
In any of the following situations, there
is a margin of error between the guide
lines on the screen and the actual dis-
tance/course on the road.
219
1. REAR VIEW MONITOR SYSTEM
9
REAR VIEW MONITOR SYSTEM
Approx. 1.5 ft. (0.5 m)
The distance that appears on the screen
between three-dimensional objects (such
as vehicles) and flat surfaces (such as the
road) and the actual distance differ as fol-
lows.
In reality, = < ( and are
equally far away; is farther than
and ). However, on the screen, the
situation appears to be < < .
On the screen, it appears that a truck is
parking approximately 1.5 ft. (0.5 m)
away. However, in reality if you back up
to point , you will hit the truck.
220
1. REAR VIEW MONITOR SYSTEM
221
1
2
3
4
5
6
7
8
9
INDEX
222
ALPHABETICAL INDEX
A
Adding destinations.................................. 49
“Address” ..................................................35
Adjust contrast/brightness...................... 201
“Advanced”................................................40
“AM” ........................................................106
Application operation ................................93
Apps..........................................................93
APPS button .......................................20, 74
“Audio” ....................................................100
Audio remote controls
(steering switches) ............................. 141
Audio system ............................................99
Audio system operating hints................. 144
Caring for your CD player
and discs......................................... 146
CD-R and CD-RW discs..................... 149
iPod .................................................... 145
MP3/WMA files................................... 148
Radio reception .................................. 144
Terms ................................................. 150
USB memory...................................... 146
B
“Beep” .....................................................197
Bluetooth®...............................132, 153, 202
Bluetooth® audio .................................... 132
Connecting Bluetooth® audio ............. 134
Playing Bluetooth® audio player......... 137
Sound setting.............................. 104, 105
Switching to Bluetooth® audio
mode............................................... 133
Bluetooth® hands-free system ................153
Bluetooth® settings ................................ 202
Bluetooth® function ON/OFF.............. 202
Displaying the paired device list ......... 206
Pairing a Bluetooth® device................ 203
Setting pin........................................... 207
C
“Calendar” .................................................79
“Call History” ...........................................173
Calling on a Bluetooth® phone............... 170
By call history ..................................... 173
By dial................................................. 170
223
By phone book ................................... 171
By POI call ......................................... 174
By speed dials.................................... 172
By “Stored” list on the
“Contacts” screen ........................... 170
Calling using a short message........... 173
CAR button .............................................190
CD........................................................... 117
Cellular phone......................................... 153
Channel category.................................... 113
Checking calendar................................... 79
Connecting a Bluetooth® phone ............ 161
Connecting Bluetooth® audio ................. 134
Controls using the
“TUNE SCROLL” knob........................ 103
D
“Day / Night Mode”.................................... 61
“Delete Personal Data” ........................... 197
Destination search................................... 33
On the “Enter Destination” screen........ 35
On the “My Destinations” screen.......... 33
Detour the segment on the route....... 51, 88
Dial.......................................................... 170
Displaying and editing the entry
information.................................... 58, 168
Displaying the radio ID............................112
Displaying the title and name..................114
Download application............................... 93
Operating application ........................... 93
DSP control.............................................104
Automatic sound levelizer (ASL) .........104
Surround function ...............................104
E
Eject button.............................................117
Email........................................................ 77
Checking “Email”.................................. 77
Receiving a new email ......................... 77
“Enter Destination”....................................35
F
“FM” ........................................................106
Fuel consumption....................................191
History .................................................192
Trip information ...................................191
Function index...........................................12
224
ALPHABETICAL INDEX
G
“General.................................................197
General settings..................................... 197
H
HD Radio™.............................................106
HD Radio™ broadcasting .......................106
Home ........................................................52
How to subscribe to an XM®
Satellite Radio .....................................112
How to subscribe.................................112
Satellite tuner technology notice .........112
I
If the satellite radio tuner malfunctions ...115
“Information” screen............................... 190
Input screen ............................................. 14
Inserting or ejecting a disc ......................117
Ejecting a disc .....................................117
Inserting a disc ....................................117
iPod........................................................ 123
About iPod.......................................... 145
Compatible models..............................145
iPod cover art..........................................127
L
“Language”..............................................197
Limitations of the navigation system ........ 66
List screen................................................ 16
M
“Map”.........................................................19
Map icons................................................. 29
POI icons.............................................. 29
Traffic messages .................................. 86
Map information ....................................... 68
Map layout.................................................28
Map screen .............................................. 25
Map settings............................................. 61
MP3.........................................................117
MP3/WMA files........................................117
Playable bit rates.................................148
Sampling frequency.............................148
Multicasting (only when listening
to an HD Radio™ channel)..................109
“My Destinations” ................................33, 52
225
N
“Navigation” menu screen........................ 21
Navigation operation.................................20
Navigation setting .....................................61
Navigation system .................................... 19
O
“Options” button........................................ 46
Overview buttons and
“Applications” menu screen............ 20, 74
Overview guidance screen ...................... 22
P
“Phone”................................................... 154
Phone book.............................................171
Phone book data..................................... 159
Phone settings....................................... 209
Picture slideshow..................................... 75
Displaying the pictures......................... 75
Playing picture slideshows................... 76
“Pictures”...................................................75
Play/Pause button...................................100
Playing a MP3/WMA disc........................120
Playing repeat and random order........122
Selecting a desired file ........................121
Selecting a desired folder....................121
Playing a USB memory/iPod...................124
Repeat and random play functions......128
Selecting a desired song.....................125
Playing an audio CD ...............................118
Playing repeat and random order........120
Selecting a desired track.....................119
Playing Bluetooth® audio ........................137
Repeat and random play functions......140
Selecting a desired song.....................138
“POI” .........................................................29
POI call ...................................................174
POI icon ....................................................29
Presetting a channel ...............................113
Presetting a station .................................106
PWR VOL knob.......................................102
226
ALPHABETICAL INDEX
Q
Quick guide.................................................9
R
Radio broadcast data system .................107
Radio reception.......................................144
AM.......................................................144
FM .......................................................144
XM®.....................................................145
Rear view monitor system.......................213
Recalculating the route by the
traffic messages ................................... 89
Receiving on a Bluetooth® phone.......... 175
Reconnecting the Bluetooth® phone...... 164
Registering a entry........................... 52, 165
Displaying and editing the entry
information................................ 58, 168
Registering a entry
as “Speed Dials ............................. 167
Registering a new entry................ 52, 165
Sending stored contacts to a
USB memory .................................... 60
Registering “Home”.................................. 52
Route guidance.........................................44
Route guidance screen ............................ 44
“Route Options”.........................................64
Route preferences...............................43, 64
Route settings .......................................... 64
S
Satellite radio (SAT)................................112
Screens for general settings ...................197
Delete personal data ...........................199
Selecting a language...........................198
“SEEK/TRACK” button............................100
Selecting a channel.................................114
Selecting a station...................................107
Setting “Home” as the destination............ 33
Setting the route....................................... 43
Setup.......................................................195
SETUP button .........................................196
“Setup” screen........................................ 196
Short message function ......................... 179
Checking received short messages.... 179
Checking sent short messages .......... 180
Sending a new short messages ......... 180
227
Showing the tire pressure screen ........... 193
SMS message ........................................ 179
“Speed Dials”.................................. 167, 172
Starting route guidance screen................ 42
Steering switches.................................... 141
Switching audio source........................... 103
Switching to AUX mode.......................... 131
Switching to Bluetooth® audio mode ...... 133
Switching to CD mode ............................ 118
Switching to radio mode .........................106
Switching to satellite radio mode ............ 113
Switching to USB or iPod mode.............. 124
T
Talking on the Bluetooth® phone........... 176
Adjusting the receiver volume............ 177
Dialing a second number ................... 177
Incoming call waiting.......................... 175
Sending tones .................................... 177
Telephone............................................... 153
Telephone (hands-free system for
cellular phone).................................... 153
About the phonebook
in this system.................................. 159
Using the phone switch...................... 158
When you sell or dispose of the
vehicle ............................................ 159
Terms......................................................150
ID3 tag.................................................150
ISO 9660 format..................................150
m3u .....................................................150
MP3.....................................................150
Packet write.........................................150
WMA....................................................150
WMA tag..............................................150
To display map screen............................. 25
Tone and balance ...................................105
Balance ...............................................105
Tone ....................................................105
Traffic announcement .............................108
Traffic message setting............................ 90
“Traffic Messages” ....................................86
“TUNE SCROLL” knob............................103
Turn off display .......................................200
Turning the audio system on or off .........102
U
USB memory...........................................146
USB memory/iPod ................................. 123
Connecting a USB memory or iPod ... 123
Playing a USB memory or iPod.......... 124
Sound setting ............................. 104, 105
Switching to USB or iPod mode ......... 124
Using the phone switch...........................158
228
ALPHABETICAL INDEX
V
Vehicle information .................................189
Voice command system......................... 185
Voice guidance ........................................ 45
Volume adjustment ...................45, 177, 197
W
“Waypoint”.................................................49
When you release your car.....................159
WMA ...............................................120, 148
Z
Zoom in button..........................................27
Zoom out button........................................27

Navigation menu