Harman Kardon Avr 240 Users Manual Quick Start Guide
AVR 240 to the manual 200736e1-f335-40f3-9c83-e935939663c8
2015-01-25
: Harman-Kardon Harman-Kardon-Avr-240-Users-Manual-235839 harman-kardon-avr-240-users-manual-235839 harman-kardon pdf
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
AVR 240 QUICK-START GUIDE Thank you for purchasing a Harman Kardon® AVR 240. This Quick-Start Guide will help you with a basic system installation. For detailed information on any step in this Guide, please refer to the pages referenced in the Owner’s Manual. We strongly recommend that you read the Owner’s Manual for complete details on how to install, configure and operate the AVR 240, as well as for the important safety information it contains. Figure 1 – Speaker Placement CENTER SPEAKER (Green) FRONT LEFT SPEAKER FRONT RIGHT SPEAKER (Red) (White) SURROUND RIGHT SPEAKER The colors shown for each speaker correspond to the matching output terminal connection on the back of the AVR 240 (see page 8). (Gray) SUBWOOFER (Purple) Connections Color Guide Audio Connections Left Right SURROUND LEFT SPEAKER Front Center Surround Subwoofer Surround Back (Blue) SURROUND BACK LEFT SPEAKER (Brown) SURROUND BACK RIGHT SPEAKER (Tan) Digital Audio Connections Coaxial Optical Video Connections Composite S-Video Match the colored jacks on the AVR 240 to the appropriate jacks on your source equipment or speakers. The colors are standardized, but not all equipment or connectors use them. Step 1. Place your speakers in the listening room (see pages 17–18). SPEAKER PLACEMENT AVR 240 QUICK-START GUIDE The Bridge LINE IN/SUB/LFE SUBWOOFER + _ FRONT RIGHT SPEAKER Step 2. Connect the speakers to the receiver: red (+) on speaker to colored (+) on receiver, and black (–) to black (–) (see page 15). Step 3. Connect the Subwoofer Pre-Out jack to the Line-In jack on your subwoofer (see page 15). You may adjust the settings on the subwoofer later as needed. + _ FRONT LEFT SPEAKER + _ SURROUND BACK RIGHT SPEAKER + _ SURROUND BACK LEFT SPEAKER + _ SURROUND RIGHT SPEAKER + _ SURROUND LEFT SPEAKER + _ CENTER SPEAKER Figure 2 – Speaker Connections Figure 3 – How to Use the Binding-Post Speaker Terminal FM Antenna AM Antenna CD PLAYER L R Optical Coax The TM Bridge The Bridge Figure 5 – Connecting EzSet+ Microphone AUDIO RECORDER Figure 4 – Audio Connections REC/IN Dashed lines (– – – –) indicate coaxial and optical digital audio connections. Choose either type (but not both) for each digital audio source. PLAY/OUT /EQ /EQ Step 4. Connect AM and FM antennas as shown above (see page 15). Step 5. Connect source components, as shown in Figures 4 and 6 and the Device Connection Options chart on the back of this Guide (see pages 15–16). AUDIO connections: Right channel (red) on source to right (red) on AVR, and left channel (white) on source to left (white) on AVR. DIGITAL AUDIO connections, if available: Choose either coax (orange) to coax (orange) OR optical to optical for each device. The Coax 1 input defaults to the DVD player, and the Optical 1 input defaults to Video 2 (Cable/Sat), but either may be reassigned. Assign the other digital inputs and outputs as appropriate for your equipment (see Step 7). VIDEO connections: Choose either composite (yellow) or S-video (4-pin) for each video source. Connect the Composite and S-video Monitor outputs to your video monitor (TV). Switch your TV set’s input to match the type of video used for the currently selected source. TM Bridge : Make sure the AVR 240 is turned off, then connect the optional TheBridge to the DMP connector. Dock your compatible iPod® (not included) in TheBridge . The TM TM Step 6. Plug all components into AC power outlets. The outlets on the back of the AVR 240 should be used only for low-current products, such as CD or DVD players, and the total should not exceed 100 watts. Basic Receiver Configuration Step 7. Select digital inputs: If your DVD is connected to Coax 1, and your cable or satellite TV box (Video 2 source) is connected to Optical 1, no adjustment is needed. For any other digital-device connections, use the On-Screen Input Setup menu, or the front-panel Digital Select and arrow buttons to select digital input (see pages 21, 35). Step 8. Select a surround mode: Press the Surround Mode button on the front panel to select Dolby ® Pro Logic ® II – Movie. (You may select other modes later as you become familiar with the AVR 240; see pages 21–23 and 32–37.) + to configure and optimize your system: Step 9. Use Plug the EzSet+ microphone into the front-panel Headphones Jack (Figure 5). Place the microphone at the center of the room, or at your normal listening position. If desired, the microphone may be attached to a standard camera tripod using the threads on the bottom of the microphone. Activate EzSet+ using the on-screen menu system (see pages 23–25). As EzSet+ senses the output of each speaker, you will hear loud test signals. When the on-screen menu indicates that setup is complete, your system is adjusted for output levels, delay times and speaker settings. Unplug the microphone and store it for future use. Step 10. Your system is configured – sit back and enjoy! SPEAKER AND AUDIO CONNECTIONS TV or Video Monitor R VIDEO Video S-Video Cable or Sat or HDTV Set-Top Box (Video 2) Component Video Y In/Rec Pb Pr Component Video Y Pb Pr L OUT R Video Optical Coax S-Video IN Out/Play The Bridge DVD PLAYER Component Video L R Video Y S-Video Pb Optical Pr Coax Figure 6 – Video Connections Dashed lines (– – – –) indicate coaxial and optical digital audio connections. Choose either type (but not both) for each digital audio source. Dotted lines (••••) indicate component, composite or S-video connections. Component video is the preferred connection when available, but you may use any of the three types (but not more than one). When component, composite and S-video sources are connected to the AVR, you must also connect all outputs from the AVR to your TV. Device Connection Options: Recommended connections are shown in red, but connections may be made to best fit your system requirements. The Video 3 inputs are on the front panel of the receiver. Device Input Name CD Player DVD Player VCR Cable Box or Satellite Receiver CD DVD Video 1 Video 2 The TM Bridge Audio Recorder TV or Projector Audio Input Connections CD L/R Inputs, Optical Digital 1 or 2, or Coaxial Digital 1 or 2 Coaxial Digital 1 or 2, Optical Digital 1 or 2, or DVD L/R Inputs Video 1 L/R Inputs Video 2 L/R Inputs, Optical Digital 1 or 2, or Coaxial Digital 1 or 2 Inputs* The Bridge DMP TheBridge DMP Connector Tape Tape L/R Inputs, Optical Digital 1/2** or Coaxial Digital 1/2** Inputs Not applicable Not required TM TM Audio Output Connections Video Connections Not required Not required Video 1 L/R Outputs Not required Not required Tape L/R Outputs, Digital Optical** or Coaxial Outputs** Not required Not required DVD Component, Composite or S-Video Video 1 Composite or S-Video Input and Output Video 2 Component, Composite or S-Video Input Not required Not required Monitor-Out Component, Composite and/or S-Video * Check with your cable company to determine whether digital audio is available for all channels. It may be necessary to make BOTH analog and digital connections if it is not. ** Digital audio recorders only. ® Power for the Digital Revolution. ® VIDEO CONNECTIONS 250 Crossways Park Drive, Woodbury, New York 11797 www.harmankardon.com © 2005 Harman International Industries, Incorporated. All rights reserved. Harman Kardon, Harman International and Power for the Digital Revolution are registered trademarks, and The Bridge and EzSet+ are trademarks, of Harman International Industries, Incorporated. Dolby and Pro Logic are registered trademarks of Dolby Laboratories. iPod is a registered trademark of Apple Computer, Inc. Part No. CQE1A259Z VCR (Video 1) L
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Page Count : 4 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:b42565cc-53f6-4f7b-8757-b4ff2c918c46 Producer : QuarkXPress(tm) 6.5 X Press Private : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%DocumentCustomColors: (PANTONE 466 C).%%+ (PANTONE 464 CVC copy).%%+ (PANTONE 361 C).%%+ (PANTONE 464 C).%%+ (PANTONE 2582 C).%%+ (PANTONE Process Blue C).%%+ (PANTONE Red 032 C).%%+ (PANTONE Warm Gray 7 C).%%+ (PANTONE 433 C).%%+ (PANTONE 299 C).%%+ (PANTONE 877 C).%%+ (PANTONE 1505 U).%%+ (PANTONE Yellow 012 U).%%CMYKCustomColor: .12 .22 .43 0 (PANTONE 466 C).%%+ .47 .65 1 0 (PANTONE 464 CVC copy).%%+ .69 0 1 0 (PANTONE 361 C).%%+ .1 .49 1 .35 (PANTONE 464 C).%%+ .46 .72 0 0 (PANTONE 2582 C).%%+ 1 .1 0 .1 (PANTONE Process Blue C).%%+ 0 .9 .86 0 (PANTONE Red 032 C).%%+ 0 .08 .14 .38 (PANTONE Warm Gray 7 C).%%+ .33 .03 0 .95 (PANTONE 433 C).%%+ .85 .19 0 0 (PANTONE 299 C).%%+ 0 0 0 .4 (PANTONE 877 C).%%+ 0 .42 .77 0 (PANTONE 1505 U).%%+ 0 .18 1 0 (PANTONE Yellow 012 U).%%EndComments Create Date : 2005:08:04 12:03:19Z Creator Tool : QuarkXPress(tm) 6.5 Modify Date : 2005:08:05 15:46:51-04:00 Metadata Date : 2005:08:05 15:46:51-04:00 Document ID : uuid:017dd316-a420-4aec-85c7-27f7704b3af4 Format : application/pdf Title : AVR 240 Quick Start Guide Creator : QuarkXPress(tm) 6.5EXIF Metadata provided by EXIF.tools