Harman Magnafire Sf Owner S Manual
2014-07-05
: Harman Harman-Magnafire-Sf-Owner-S-Manual harman-magnafire-sf-owner-s-manual harman pdf
Open the PDF directly: View PDF 
.
Page Count: 18
| Download | |
| Open PDF In Browser | View PDF |
Installation & Operating Manual NOTICE: SAVE THESE INSTRUCTIONS ! WARNING HOT SURFACES! Glass and other surfaces are hot during operation and cool down. Model(s): SF250 Coal Stove Hot glass will cause burns. • Do not touch glass until it is cooled • NEVER allow children to touch glass • Keep children away • CAREFULLY SUPERVISE children in same room as stove. • Alert children and adults to hazards of high temperatures. High temperatures may ignite clothing or other flammable materials. • Keep clothing, furniture, draperies and other flammable materials away. SAFETY NOTICE Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property damage, bodily injury, or even death. FOR USE IN THE U.S. AND CANADA. not SUITABLE FOR INSTALLATION IN MOBILE HOMES IF THIS Harman® STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. FOR YOUR SAFETY, FOLLOW INSTALLATION DIRECTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN YOUR AREA. Contact your local authority (such as municipal building department, fire department, fire prevention bureau, etc.) to determine the need for a permit. Cette guide d’utilisation est disponible en francais. Chez votre concessionnaire de Harman®. save these instructions. 3-90-70738R9_08/13 TABLE OF CONTENTS Safety Considerations. . . . . . . . . . . . . . 3 Specifications . . . . . . . . . . . . . . . . . . . . 4 Assembly. . . . . . . . . . . . . . . . . . . . . . . . 5 Installation. . . . . . . . . . . . . . . . . . . . . . . 6 Chimney & Venting . . . . . . . . . . . . . . 7-8 Operating Instructions. . . . . . . . . . . . . . 9 Maintenance . . . . . . . . . . . . . . . . . . . . 10 Optional Bent Hot Water Coil . . . . 11-12 Testing Label. . . . . . . . . . . . . . . . . . . . 13 Warranty . . . . . . . . . . . . . . . . . . . . 14-15 Service & Maintenance Log. . . . . . . . 16 Signature Page. . . . . . . . . . . . . . . . . . 18 = Contains updated information 2 3-90-70738R9_08/13 Safety Considerations CAUTION • Keep Children Away • May Cause Serious Burns • All Surfaces of stove are hot. Do not touch. • Keep children away. • Serious burns will result if touched. Fuel/Firing Warnings Danger Do not use chemicals or fluids to start or “freshen up” a fire. Severe body burns or a fire in your home could result. Do not burn garbage, gasoline, thinners, drain oil or engine oil, kerosene, or fuel oil, etc. An explosion, a house fire, or personal injury could result. Keep all such liquids well away from the stove while in use. Curing Paint During the first few hours of burning, a blue smoke will be observed rising from the painted surface of the stove. It is advisable to increase the amount of fresh air (open window) in the room during this breaking-in period. Do not be alarmed, this is normal and does not cause harm. Mobile Homes This Harman® Stove is not approved for installation in mobile/manufactured homes. SPECIAL WARNING: NEVER OPERATE YOUR STOVE WITH THE FIRE OR ASH DOOR OPEN! Keep Ash Pan Empty Excessive ash buildup will block the airflow around the grates. This, and only this, will cause the grates to warp and sag. Neglect is not covered by your stove’s warranty. Never burn materials other than coal. A chimney fire or heat exchanger failure could result. This includes large amounts of corrugated boxes, wood shavings, paper scraps, garbage or other burnable materials. If chimney pipes or connectors reach 500 degrees fahrenheit (maximum temperature), the stove is being over-fired. We recommend the purchase of a Magnetic Temperature Gauge to monitor the stove and stack temperatures relative to the amount of draft the customer permits the stove to operate. It has been verified that creosote will ignite at 650 degrees fahrenheit. It is the owner’s responsibility to follow these recommendations. This stove consumes air when it is burning. if your house is tightly sealed and insulated, it is advisable that a window in the vicinity be opened slightly while the stove is burning. Information contained in this manual is manufacturer’s recommendations and if there is any difference between our recommendations and local code requirements, we suggest following local code requirements. 3 3-90-70738R9_08/13 Specifications 5 13/16 32 5/8 42 15/16 7/8 36 11/16 35 3/4 42 15/16 20 1/2 4 3-90-70738R9_08/13 Assembly Blower The blower slides into the channel bracket on the rear of the stove as shown at right. Plug the blower into a properly grounded receptacle. Shaker Handle The shaker handle installs onto the shaker handle mount using the two hex-bolts and washers provided. Firebricks The SF250 uses 14 “standard” firebricks, as shown below. These standard firebricks measure 9” X 4½” X 1¼” each. The firebricks are already installed in the stove but can be removed to lighten the stove for moving. The doors can also be removed by simply lifting them off of the hinges. Firebrick Diagram 5 3-90-70738R9_08/13 Installation WARNING: This stove must be installed in accordance with all state and local building code requirements. Locating the stove Locate the stove as close to the chimney or flue as possible, while still maintaining the clearances to combustibles. Adjustable Leveling Feet To accomodate an un-even hearth surface, the SF250 is equipped with adjustable leveling feet. Each foot can be turned in or out of the leg to lower or raise that corner of the stove. Locate the stove where there is sufficient air supply for ventilation and proper combustion. Clearance to Combustibles Safe stove clearance to combustible walls is 24” to the rear and 36” to the sides and front. Do not place furniture and the like directly in front of the stove. Floor Protection Floor protection for a combustible floor should consist of 3/8” millboard or a stove board providing equal protection(k=.84, R=.45). The floor protection should extend 8” to the rear and either side and 16” in front of the stove. The floor protection should also extend 2” to either side of the chimney connector, to the wall where the connector enters the flue. Alternate floor protector dimension may be used as long as they satisfy the measurement requirements shown below. Minumum size floor protection for a corner installation hearth pad is 54" x 54" (USA ONLY). Turn the round foot in or out to level each corner of the stove. It is recommended that you have your unit installed and serviced by professionals who are certified by the National Firplace Institute (NFI) as NFI Specialists. Floor Protection 54" 24” 8” 54" 8” 36” Floor Protection 6 16” 3-90-70738R9_08/13 Chimney & venting Types Of Chimneys The chimney is one of the most important, yet most neglected and misunderstood portions of any solid fuel burning stove installation. Do not connect this stove to a chimney flue serving another heating device. More than 10 Ft. (3 m) 10 Ft. (3 m) THE STOVE MUST BE CONNECTED TO ITS OWN TILE-LINED FLUE. A MINIMUM FLUE SIZE OF 8” X 8” IS NECESSARY FOR PROPER OPERATION. 2 Ft. (.6 m) Min UNDER NO CIRCUMSTANCES SHOULD A MANUAL FLUE DAMPER BE INSTALLED IN THE SMOKE PIPE BETWEEN THE STOVE AND THE CHIMNEY. NO DAMPER, HEAT SAVER OR AUTOMATIC VENT DAMPER DEVICE SHOULD BE INSTALLED IN OR ON THE SMOKE PIPE. Height necessary above any roof surface within 10 Ft. (3 m) 3 Ft. (.9 m) minimum above exit point Ridge CAUTION: THE CHIMNEY MUST BE A CLASS “A” CHIMNEY, IN GOOD OPERATING AND CLEAN CONDITION. NOTE: THE USE OF ALUMINUM TYPE “B” GAS VENT FOR SOLID FUELS IS UNSAFE AND PROHIBITED BY THE NATIONAL FIRE PROTECTION AGENCY CODE. There are three types of class “A” chimneys: 1. Masonry with tile liner, to include brick or stone. It must be supported on grade level foundation. 2. Insulated, manufactured chimney, listed or certified by a national test agency. 3. Triple-wall metal class “A” chimney, listed or certified by a national test agency. If your masonry chimney has not been used for some time, have it inspected by a qualified person. If a listed or certified manufactured chimney is to be used, make certain it is installed in accordance with the manufacturer’s instructions and all local and state codes. The minimum recommended height for solid fuel chimneys is 16 feet from the stove collar. The chimney must be two feet higher than anything within ten feet. It also must extend three feet above the point where it intersects or exits the roof line. Chimney The three foot, two foot, ten foot rule In order to have a properly operating solid fuel heating system, the chimney must be capable of providing the necessary draft. The minimum required draft is .06 inches of water column (W.C.). This must be measured using a draft gauge. If the chimney cannot supply this constant draft, the stove will not operate properly. A barometric damper may be used and properly adjusted to compensate for excessive draft only. IMPORTANT: When you measure the the draft, the stove must be operating with sufficient time given for the stove and chimney to warm. Burn for at least thirty minutes. The draft reading is best taken 18” up from the center of the flue outlet, in the connector pipe. Drill a hole in the pipe for the meter tube, and fill it with a screw or silicone when done with the test. IMPORTANT: The connector pipe must be 24 gauge or thicker. When connecting the flue pipe to the stove, the first section should be installed inside the stove collar. It should be secured to the collar with, at least, three screws or rivets. Do not pass the connector pipe through a wall or ceiling without first checking with your local codes. If allowed, use only approved pass-thru methods. NOTE: All horizontal runs of venting should have a 1/4 inch of rise per foot of length. Use no more than two 90° elbows in the connector. If a barometric damper is needed, to compensate for excessive draft, install it only in a vertical section of vent pipe. 7 3-90-70738R9_08/13 Chimney & venting Possible causes of insufficient draft; A. Chimney Leaks - Air leaking in around a loose fitting cleanout door, flue pipe joints and/or seams not secured, improper plug openings or defective masonry. B. Chimney Too Short - The general rule for chimneys; 16 feet tall, three feet above the roof exit, and two feet taller than anything within ten feet. C. Blocked Chimney - Have the chimney cleaned and inspected prior to installation and before each heating season. D. Trees Or Other Topographical Barriers - Impeding on the chimney’s operation or causing a down draft situation. This can also be caused by adjacent buildings or another roof of the same structure giving air currents a downward swirl. NOTE: The chimney on the illustrated house is too low, it should be raised to compensate for down draft potential. Wind direction The most common cause of poor draft is an improperly sized flue liner. It is recommended that the inside dimensions of the liner be at least as large as the appliance flue outlet and no larger than 125% of the collar for a round flue. An example, a 8” flue collar is 50 square inches. Increased by 25% would be 63 square inches, or approximately a 9” round flue. In general for round liners, it is recommended that they not be increased by more than one inch from that of the stove collar. This will help ensure proper draft with the lower flue temperatures. REMEMBER; A solid fuel burning stove can only perform as well as its venting system will allow it to. THE MOST IMPORTANT THING TO REMEMBER ABOUT CHIMNEYS IS THEIR NEED FOR MAINTENANCE AND CLEANING. IF A CHIMNEY IS NOT CLEANED ON A FREQUENT BASIS, IT WILL AFFECT THE DRAFT AS WELL AS BEING A CONTRIBUTING CAUSE TO A POSSIBLE CHIMNEY FIRE. IF YOU HAVE A CHIMNEY FIRE: 1. GET EVERYONE OUT OF THE HOUSE. 2. CALL THE FIRE DEPARTMENT. 3. CLOSE THE DRAFT CONTROL KNOBS ON THE STOVE. DO NOT USE THE CHIMNEY UNTIL IT HAS BEEN THOROUGHLY CLEANED AND INSPECTED BY A QUALIFIED PERSON. E. Chimney Size - The chimney can not be smaller than the flue exit from the appliance. Too large of a chimney could stay too cool to promote adequate draft. F. Chimney Offsets - Offset chimneys should be avoided. The offset area can collect debris and cause a blockage. G. Elbow restrictions - There should be no more than two 90° elbows or the equivalent used in connecting the stove to the chimney flue. H. Shared Flue - No more than one appliance shall vent into a single flue. 8 3-90-70738R9_08/13 operating instructions The SF250 is approved for use with coal only. Burning wood or other such fuels in this stove, except for the purpose of igniting a coal fire, is prohibited. Starting A Fire Begin by opening the draft control knobs on both the load door and the ash door. Open both doors. Be sure all items have been removed from the ash pan (i.e. touch-up paint, warranty registration, etc...) Place aproximately eight sheets of newspaper, crumbled, on top of the grates. Lay some kindling on top of the crumbled paper. This kindling should be dry and no larger than 3/4 in. diameter. It should be layered in a criss-cross fashion to allow good air flow. Now place some slightly larger pieces of wood (about 2” diameter) on top of the kindling. Using a match or grill lighter, ignite the paper at the bottom just inside the door. Close both doors and allow the kindling and larger wood to catch fire. After around five minutes, open the load door slightly, for a few seconds and then open completely. This is a good practice to get into as it will allow any smoke and gases to clear away from the door opening. Add small compact pieces of wood when the kindling is burning hot. When a substantial bed of hot wood coals is established, start adding coal in small amounts at a time. Allow a few minutes between coal loadings to be sure that what you’ve added is ignited. You can keep the ash door open through this process, but NEVER LEAVE THE STOVE UNATTENDED WITH A DOOR OPEN. Once you have a bed of burning coal, you can load coal into the stove to the top of the firebricks. Always make sure there is some flame showing through the coal. This will ensure the gases are being burned and not accumulating in the firebox. After a good coal ignition, set the draft controls on the load door to about 1/4 turn open. The draft control on the ash door is used to control the rate of burn. After starting a fire, keep it about 2 full turns open for about 30 minutes. Then, adjust further closed to the proper output level. Normal operation will be between cracked and one turn open. Since coal responds slowly to draft adjustments, make only small adjustments and allow time in between. Loading Coal should only be added when there is a reasonably hot fire. The coal bed should be bright and vigorous. If the fire is burning hot and there is a deep bed of coals, full loads can be added. If it is not as described, add coal in small batches only. 9 Increasing Heat From A Low Fire Every effort should be made not to let a coal fire burn so long that it has started to die. This will cause the reloading process to be much longer, and there is a good posibility of losing the fire. Do not shake or stir a low fire. Open the draft control all the way until the fire gets as hot as possible. Start adding small batches of coal and follow the instructions for starting a fire. Once there is a good bed of burning coals, the grates may be shaken to remove ashes. Shaking Ashes Shaking should be done only when there is a hot fire burning. The frequency of shaking will depend on the degree of burning. Shaking should be done at least once per day, preferably twice. The best results from shaking will occur when short choppy strokes are used, rather than long, even strokes. Grasp the shaker handle with one hand and shake it, only moving the actual handle 1/2 inch or less. Do this until you start to see hot coals falling into the ash pan, then stop. Do not rock the grates, as this will allow burning coal to fall through, and you’ll lose the fire. Ashes The ashes should never be allowed to accumulate in the ash pan. Excess ash will block the required airflow through the grates and cause them to warp and sag. Neglect is not covered by your stove’s warranty. Ashes should be placed in a metal container with a tight fitting lid. This closed container of ashes should be placed on a noncombustible floor or on the ground, well away from any combustible materials, pending final disposal. If the ashes are disposed of by burial in soil, or otherwise locally dispersed, they should be retained in the closed container until all cinders have thoroughly cooled. Fuel The SF250 is approved for burning anthracite coal. Pea, Nut, and Stove sized coal are all suitable. Grates The functions of a grate system are to support the fuel load, while allowing air flow to the fire in a balanced amount. Another function is to allow for ash removal without losing the fire. The SF250 grate system provides for all of this and can be removed with no tools required. 3-90-70738R9_08/13 Maintenance Spiral Chamber Cleanout SHAKER HANDLE (external) SHAKER BAR GRATES GRATE LINK Close-up view of grate system components Periodic and Normal Everyday Maintenance Blower Motor- Clean periodically to remove pet hair and lint from the intake and fan. Cleanout Plate Removed Grates- Keep ash pan empty. CAUTION: BEFORE CLEANING THE CHIMNEY AND SMOKE PIPE, BE SURE THE FIRE IS OUT AND THE STOVE IS COOL. Avoid Chimney Fires. On a regular schedule, check for creosote and soot buildup in the chimney, smoke pipe, and spiral chamber. These areas must be kept clean. Keep a professional chimney sweep in mind. Steel brushes are the safest for cleaning metal surfaces. Salt solutions and some chemical cleaners may damage the flue liner. To clean the chimney, obtain a stiff brush with an extendable handle. Insert the brush into the chimney from the top. Continue brushing and sweeping downward until the entire length of the chimney is cleaned. After cleaning the chimney, any debris will be at the bottom by the clean-out door. Open the clean-out and vacuum the loose debris. Clean the smoke pipe, from the chimney to the stove, using a metal brush. In the firebox, remove all ashes and vacuum the entire firebox. Inspect and replace any cracked firebricks. Since coal and coal ashes will draw moisture, it is important to thoroughly clean the firebox at the end of the heating season. Some users apply a thin coating of oil or other rust inhibitor to the inside workings, over the summer. The main thing is that you remove all of the ash. Cleaning of the spiral chamber - Remove clean-out plate from the front of the stove. Using a 3/4” wrench, loosen the clean-out bolt approximately 2 turns. Slide the clean-out plate to one side and remove it from the opening. Scrape the spiral chamber with a putty knife or similar tool. The residue will fall down to the bottom of the chamber and can be removed through the flue opening on the back of the stove by means of a vacuum cleaner or a small scoop. 10 3-90-70738R9_08/13 optional bent hot Water coil Optional Bent Hot Water Coil - Part #3-10-49202 Use a hole saw and the template supplied with the coil to make two holes through the side wall of the stove. Keep the coil holes above the firebrick and away from the loading door. Place one of the supplied nuts on each leg of the coil. Place the coil through the holes in the stove, and adjust the nuts so that the pipes stick out about 1¼” to 1½” from the sidewall of the stove. Put flat washers and nuts on the outside, and tighten within ¼ inch. Place fiberglass gasket around each pipe at the washers and tighten securely. You are now ready to run pipes according to one of the following examples. Washer Outside Nut Packing Outside Nut Stove Side Example 1: Thermo-siphon Method. This is the simplest and most economical method, providing the existing water heater (storage tank) is within 10 feet of the stove. The water inlet, where the Temp/Pressure relief valve is located, must be higher than the top leg of the water coil. The storage tank should be elevated, if necessary, to allow for proper thermo-siphon action. 1. Turn off the water heater and the water supply to it. Drain the tank completely. 2. Remove the Temp/Pressure relief valve and discard. Install a short ¾” nipple and tee (1) along with a new Temp/Pressure relief valve. 3. Run ¾” copper tubing, along with the necessary fittings, between the storage tank and the top leg of the coil. Install a ¾” vent elbow and automatic “float type” air vent (2) in the high point of the line. Within two feet of the top leg of the coil, install a 150 lb. pressure relief valve (7). Run ¾” tubing from the release exit of both relief valves, downward (3) so that the hot water may escape in the event of over-heating. 4. Remove the drain valve, at the bottom of the storage tank. Install a ¾” nipple and tee, and reinstall the drain valve to the tee (4). Run ¾” copper tubing, with the necessary fittings, between the drain/tee combination and the lower leg of the coil. After all of the connections are completed, you can refill the tank. Restore power to the water heater ONLY after the tank has been completely refilled. EXAMPLE 1: Thermo-siphon Method. (less than 10 feet.) 11 3-90-70738R9_08/13 Water coil option Example 2: Circulating pump method. Used when the distance is more than ten feet or when the stove is on a higher level than the existing water heater. In addition to a circulator, you may want to add a aquastat to control the pump according to water temperature. This is not necessary if the circulator is left run continuously. Another option is a gate valve placed near the circulator to control the rate of flow. 1. Turn off the water heater and the water supply to it. Drain the tank completely. 2. Remove the Temp/Pressure relief valve and discard. Install a short ¾” nipple and tee (1) along with a new Temp/Pressure relief valve. 3. Remove the drain valve, at the bottom of the storage tank. Install a ¾” nipple and tee, and reinstall the drain valve to the tee (4). 4. Install a circulating pump (6) as shown. Run ¾” copper tubing from the circulator to the lower leg of the coil. This is where the optional gate valve (5) can be installed. 5. Install a ¾” tee and a 150 lb. pressure relief valve (7) in the top leg within 2 feet of the top outlet of the water coil. 6. Complete the copper line by running it back to the tee at the top of the water tank, making sure to install a vent elbow and automatic air vent (2) at the high point of the line. The optional aquastat can be installed in this line a maximum of six feet from the stove. The aquastat must be a “close on temperature rise” type and must be wired and set to turn on the circulator when the water temperature reaches 120˚ Farenheit. The system is now ready to be refilled and power restored to the water heater ONLY after the tank is filled. EXAMPLE 2: Circulator Method. (more than 10 feet.) 12 3-90-70738R9_08/13 SA M PL E testing label * This appliance is also approved for installation into a shop 3-90-70738R9_08/13 hearth & home Technologies lImITEd lIFETImE wArrANTY Hearth & Home Technologies, on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer. wArrANTY COvErAgE: HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period, HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty is subject to conditions, exclusions and limitations as described below. wArrANTY PErIOd: Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent, authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for parts and labor for covered components is produced in the following table. The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These time periods reflect the minimum expected useful lives of the designated components under normal operating conditions. Warranty Period Parts Labor 1 Year 2 years HHT Manufactured Appliances and Venting Gas X X Wood X X X 3 years Pellet EPA Wood Coal X X X X X X X X X Components Covered Electric Venting X X All parts and material except as covered by Conditions, Exclusions, and Limitations listed Igniters, electronic components, and glass Factory-installed blowers Molded refractory panels X Firepots and burnpots 5 years 1 year 7 years 3 years 10 years 1 year X Limited 3 years Lifetime X X X X X 90 Days X X X X X X X X Castings and baffles X X Manifold tubes, HHT chimney and termination Burners, logs and refractory Firebox and heat exchanger X X All replacement parts beyond warranty period See conditions, exclusions, and limitations on next page. 4021-645F 02-18-13 14 Page 1 of 2 3-90-70738R9_08/13 wArrANTY CONdITIONS: • This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of HHT authorized dealers is available on the HHT branded websites. • This warranty is only valid while the HHT appliance remains at the site of original installation. • This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance resides. • Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service from a dealer other than the dealer from whom you originally purchased the product. • Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges for parts are not covered by this warranty. wArrANTY EXCluSIONS: This warranty does not cover the following: • Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and exterior surface finishes may occur. This is not a flaw and is not covered under warranty. • Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items, or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes. • Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, batteries and the discoloration of glass. • Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints related to this noise are not covered by this warranty. • Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/ incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7) installation or use of components not supplied with the appliance or any other components not expressly authorized and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing; and/or (9) interruptions or fluctuations of electrical power supply to the appliance. • Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance. • Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed. • HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Information is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consideration must be given to appliance location and configuration, environmental conditions, insulation and air tightness of the structure. This warranty is void if: • • • The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling, cracking and discoloration of steel or enamel finishes. The appliance is subjected to prolonged periods of dampness or condensation. There is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation. lImITATIONS OF lIAbIlITY: • The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you. This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EXPRESSED WARRANTY SPECIFIED ABOVE. 4021-645F 02-18-13 15 Page 2 of 2 3-90-70738R9_08/13 Service & Maintenance Log Date Of Service 16 Performed By Description Of Service 3-90-70738R9_08/13 notes 17 3-90-70738R9_08/13 At Harman®, we build each product to a standard, not a price. (Signature of Boxer) Your premium quality hearth product designed and assembled by the experienced and skilled members at Harman® in Halifax, PA, USA. Proudly Printed On 100% Recycled Paper
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Create Date : 2013:11:01 11:13:38-04:00 Creator : Adobe InDesign CS6 (Windows) Modify Date : 2013:11:08 11:39:54-06:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2013:11:08 11:39:54-06:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:a5c71aba-657d-4520-a17b-8b718f6b2e83 Original Document ID : adobe:docid:indd:4c67997f-6d4e-11de-8897-d27510167b41 Document ID : xmp.id:F9E795FA0743E31183F6FF9964267B87 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:C265701A12FAE211853DE569528B42C5 Derived From Document ID : xmp.did:90470CC210FAE211853DE569528B42C5 Derived From Original Document ID: adobe:docid:indd:4c67997f-6d4e-11de-8897-d27510167b41 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2013:11:01 11:13:38-04:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 18EXIF Metadata provided by EXIF.tools