Harman JBLCONTROLXWLS Wireless Speaker User Manual TR01319 Control X Wireless OM Global

Harman International Industries, Inc Wireless Speaker TR01319 Control X Wireless OM Global

User Manual_rev.pdf

CONTROL X WIRELESS2-way 5.25” (133mm) Portable Stereo Bluetooth® SpeakersOWNER’S MANUALThe JBL® brand has been involved in every aspect of music, film recording and reproduction from live performances to the recordings you play in the home, car, or on-the-go. We’re confident that the JBL system you have chosen will provide every note of enjoyment that you expected and that when you think about purchasing additional audio equipment for your home, car or office, you will once again choose a JBL product.The JBL Control X is an advanced indoor/outdoor* Bluetooth® active loudspeaker system that allows you to enjoy your favorite music in remote locations around the home or in commercial spaces. To ensure trouble-free performance, please carefully read these instructions completely before connecting or using the system. *Please note that while the JBL Control X WIRELESS is an all weather outdoor loudspeaker, it is not waterproof. These speakers should NOT be submerged or directly exposed to water, ice, snow or sustained moisture. Do not spray water into the speaker’s rear port.THANK YOU FOR CHOOSING THIS JBL® PRODUCTENGLISH
2UNPACKING THE SYSTEMCarefully unpack the system. If you suspect damage from transit, report it immediately to your dealer and/or delivery service. Keep the shipping carton and packing materials for future use. Open the package and verify the following contents:INCLUDED1 x JBL Control X Wireless Primary speaker1 x JBL Control X Wireless Secondary speaker2 x AC power cord1 x Owner’s Manual1 x Safety sheetTOP-PANEL CONTROLSPRIMARY SPEAKER1. Power2. Bluetooth pairing (Press and Hold 2 seconds to un-pair current Bluetooth device)3. Transport control button (Previous track)4. Play / Pause5. Transport control button (Next track)6. Volume Down7. Volume Up8. Battery level indication9. Front panel LED indicationLED informationFixed Quick Flash Regular FlashWhite On / No Bluetooth device connectedAdditional speaker association mode Volume Up and Down (Stops when reaches Max or Min)System is waking upBlue Bluetooth device connectedBluetooth pairing modeNote: The front LED indication times out in normal operation modeNote: To mute the systems simply press and hold volume up and down simultaneously for at least 2 seconds. Simply press volume up or volume down to un-mute the system.SECONDARY SPEAKER 1. Power2. Battery level indication3. Front panel LED indicationLED informationFixed Quick Flash Regular FlashWhite On / No Bluetooth device connectedAdditional speaker association mode Volume Up and Down (Stops when reaches Max or Min)System is waking upBlue Bluetooth device connectedBluetooth pairing modeREAR-PANEL CONTROLSPRIMARY SPEAKER AC INAUX-INL/R/L+RP SMODE WALL/OTHER123 4561. AC input connector2. Auxiliary 3.5mm audio input3. Primary-Secondary mode selector4. Boundary compensation switch a. Wall: Speaker equalization optimized for wall mounting. b. Other: Speaker equalization optimized for other placement conditions5. Left / Right / Left + Right switch a. Left: Speaker reproduces left channel information only b. Right: Speaker reproduces right channel information only c. Left + Right: Mono configuration speaker reproduces left and right channels information6. Association pin hole1 2 3 4 5 6 789123
3www.jbl.comENGLISHSECONDARY SPEAKER AC INL/R/L+RWALL/OTHER12341. AC input connector2. Boundary compensation switch a. Wall: Speaker equalization optimized for wall mounting. b. Other: Speaker equalization optimized for other placement conditions3. Left / Right / Left + Right switch a. Left: Speaker reproduces left channel information only b. Right: Speaker reproduces right channel information only c. Left + Right: Mono configuration speaker reproduces left and right channels information4. Association pin holePLACING THE SPEAKERSThese speakers can be mounted or placed on a stand, shelf or table. The following figure shows a possible indoor application. For optimal performance, do not block the rear port on the back of each speaker.Left RearChannelRight RearChannelCenter RearChannelLeft FrontChannelRight FrontChannel45 oQUICK SETUP AND OPERATIONThe speaker set is already factory setup to operate as a pair (primary and secondary).1. Connect AC power cords to AC-IN plug located at the rear of each speaker. Keep AC plugged to maintain battery fully charged.2. Press power button on each speaker(s) to start operation.3. Press Bluetooth button and pair with streaming device. (Refer to Listening to Audio from a Bluetooth capable device section below)4. If desired to use in battery mode, just unplug the AC power. Speaker and audio will not be interrupted. Reconnect to AC to recharge battery.Note: Primary and Secondary speakers’ factory default settings are as followControl / Switch Primary SecondaryMode (P) N/AWall/ Other Other OtherL/R/L+R (L) (R)Note: When the system is not playing music it will go automatically into auto standby mode. To reactivate the system, simply start playing music and the system will resume automatically. A slight delay may occur before the secondary speaker wakes up as it needs resynchronization with the primary speaker. During this phase the front LED of the secondary speaker will be blinking.Note: If the system is manually powered off using the power button, it will need to be manually powered on first to resume playing music.The system also features sound prompt commands for the following action / operation1. Power On2. Power Off3. Bluetooth pairing mode4. Bluetooth connection success5. Association mode (see Speaker association section)6. Battery low levelLISTENING TO AUDIO FROM A BLUETOOTH-CAPABLE DEVICE 1. With speaker(s) powered on AC or Battery power, Press Bluetooth button on primary speaker2. An audible prompt will indicate that the speaker successfully entered BT pairing mode. The front LED will also blink Blue as an indication that BT pairing mode is enabled.3. Search and pair with “JBL Control X” from your Bluetooth streaming device.4. An audible confirmation will be played once the streaming device successfully paired with the speaker. The front LED will stop blinking and remain Blue. Secondary speaker will confirm Bluetooth pairing by flashing front panel LED Blue for a few seconds.Note: Only one Bluetooth device can be paired at the same time with the system. If you need to un-pair the current Bluetooth device to connect a new one simply press and hold the Bluetooth button on the primary speaker for more than 2 seconds to disconnect current device. Then resume the pairing process above from step 2.LISTENING TO AUDIO FROM AUX-INBluetooth operation has priority over Aux-In input. If you want to use the auxiliary in input, any paired Bluetooth device need to be disconnected or unpaired from JBL control X Wireless by pressing and holding the Bluetooth button for more than 2 seconds or by disconnecting it from your Bluetooth streaming device.1. With speaker(s) powered on AC or Battery power, connect a 3.5mm audio cable from the audio source to the AUX-IN on the primary speaker.SPEAKER ASSOCIATIONJBL Control X Wireless speakers are factory associated to each other. In case of association problems were the secondary speaker is not playing music, WSLHZLMVSSV^HZZVJPH[PVUZ[LWZVUKL[HPSLKZLJ[PVUILSV^[VÄ_[OLPZZ\L6US`one secondary speaker can be associated at the time with a primary speaker. 1. With both primary and secondary speaker(s) powered on AC or Battery power, use a paper clip to press the association button on the back of the ZLJVUKHY`ZWLHRLY;OLMYVU[3,+^PSSÅHZO^OP[LPUKPJH[PUNHZZVJPH[PVUmode is active
4© 2015 HARMAN International Industries, Incorporated. All rights reserved.JBL and CMMD are trademarks of HARMAN International Industries, Incorporated, registered in the United States and/or other countries. Bluetooth® is a registered trademark of Bluetooth SIG, Inc. Features, specifications and appearance are subject to change without notice.HARMAN International Industries, Inc. 8500 Balboa Boulevard, Northridge, CA 91329 USA www.jbl.comTR01319_A2. Press the association button on the primary speaker. An audible confirmation will be played to indicate that the speaker successfully entered association mode. The front LED will blink blue if already paired with a Bluetooth device, otherwise it will blink white.3. Wait until association process finishes. The process is complete as soon as the front LED on each speaker stops blinking.Note: in case the association needs to be redone for speaker replace-ment or configuration change, the current association set up needs to be reset. Press and hold the FWD and REV buttons on the top of the primary speaker for more than 3 seconds.It is also possible to associate a second pair of JBL control X wireless speaker set to an existing pair to extend the system coverage. If you want to have a set of 4 speakers connected.1. With all four primary and secondary speaker(s) powered on AC or Battery power2. Use a paper clip to press the association button on the back of the second set primary speaker with the back control mode switch set to secondary “S”. The front LED will flash white indicating Association mode is active.3. Press the association button on the primary speaker of the first master set. An audible confirmation will be played to indicate that the speaker successfully entered association mode. The front LED will blink blue if already paired with a Bluetooth device, otherwise it will blink white.4. Wait until association process finishes. The process is complete as soon as the front LED on each speaker stops blinking.5. Use a paper clip to press the association button on the back of the second set secondary speaker. The front LED will flash White indicating Association mode is active.6. Press the association button on the secondary speaker of the first master set. An audible confirmation will be played to indicate that the speaker successfully entered association mode. The front LED will blink blue if already paired with a Bluetooth device, otherwise it will blink white.7. Wait until association process finishes. The process is complete as soon as the front LED on each speaker stops blinking.Note: in case the association needs to be redone for speaker replacement or configuration change, the current association set up needs to be reset. Press and hold the FWD and REV buttons on the top of the primary speaker for more than 3 seconds.MAINTENANCE AND SERVICEThe speaker enclosures may be cleaned using a soft cloth to remove fingerprints or to wipe off dust.All wiring connections should be inspected and cleaned or remade periodically. The frequency of maintenance depends on the metals involved in the connections, atmospheric conditions and other factors, but once per year is the minimum. In the event that your system ever needs service, contact your local JBL dealer or distributor, or visit www.jbl.com for a service center near you.BATTERY DISPOSALRechargeable batteries (i.e., nickel cadmium, nickel metalhydride, lithium and lithium-ion) are considered hazardous household materials and may pose an unnecessary health and safety risk.In the European Union and other locations, it is illegal to dispose of any battery with household trash. All batteries must be disposed of in an environmentally sound manner. Contact your local waste management officials for information regarding the environmentally sound collection, recycling and disposal of used batteries.SPECIFICATIONSLow Frequency Transducer: 5.25" (133mm) polypropylene graphite-filled coneHigh Frequency Transducer: 1” (25mm) CMMD® Lite dome / High Definition Imaging WaveguideRated Power: 30W per channel RMS (AC mode)Frequency Response: 62Hz - 20kHz (-6db)Sensitivity: (2.83V@1m) 87dBSignal-to-noise ratio: >75 dBPower supply: AC 100-240 VAC, 50-60HzBattery Type: Lithium-ion Polymer (7.4V, 2600mAh)Battery Charge Time: 2.4 hours @ 0.5CPlayback Time: Up to 4 hours (varies by volume level and audio content)Bluetooth® 2.1 with AVRCP profile v1.5Bluetooth® Transmitter Power: 0-4 dBmBluetooth® Transmitter Frequency Range: 2.402 – 2.480 GHzBluetooth® Transmission Range: Up to 10m (from source)Speaker Range: Up to 30m (between primary and secondary speakers)Dimensions: 9-1/4” x 6-1/2” x 6-1/4” (235mm x 165mm x 159mm)Weight: 6.5 lbs (2.95 kg)Finishes: Graphite / White / RedAC INAUX-INL/R/L+RP SMODE WALL/OTHER(For Primary Speaker Use Only)

Navigation menu