HeathCo 60WRC02TX 6002TX Remote Control Transmitter User Manual 598 1136 00

Download:
Mirror Download [FCC.gov]
Document ID	337197
Application ID	wCbcNipLk0ZFB1mKfhHx4A==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	36.19kB (452416 bits)
Date Submitted	2003-07-02 00:00:00
Date Available	2003-07-02 00:00:00
Creation Date	2003-06-13 09:15:59
Producing Software	Acrobat Distiller 5.0.5 for Macintosh
Document Lastmod	2003-06-13 11:54:16
Document Title	598-1136-00
Document Creator	Adobe PageMaker 6.52
Document Author:	Keith Peterson

Multi-Channel
Remote Control
Features
ALL OFF
PANIC
DIM
OFF
•
•
•
•
Operational range of up to 100 feet.
Controls all Heath®/Zenith Remote Home™ products.
FCC/IC tested and approved.
Flash control on compatible receivers when using the Panic
feature.
DRAFT COPY
ALL ON
ON
Battery Installation
Battery Cover
The Multi-Channel Remote Control is designed for 3 Volt operation:
1. Remove battery cover on rear of housing by pushing clip and lifting up.
2. Install 2-AAA batteries (not included)
according to polarity markings.
Two AAA
Batteries (Not
Included)
Installing 2-AAA Batteries
Setting Receiver(s) Dip Switches
The Control Panel transmitter has
preprogrammed dip switch settings for each
channel. In order for the Control Panel to
communicate with a receiver, the dip
switches on the receiver must correspond
with the preprogrammed dip switch settings
of the channel you wish to use. Note: There
are no dip switches on the Control Panel
that require setting.
1. Determine which receiver(s) will be
operated by which channel.
2. Set receiver(s) dip switches 1, 2, and 3
to match the dip switch settings for the
channel you wish to operate the
receiver(s).
3. Determine whether the receiver(s) will
be in Group A or B.
4. Set dip switch 4 on the receiver to the
same setting as Group A or B.
© 2003 DESA Specialty Products™
(Dip Switch 4 in
UP position)
(Dip Switch 4 in
DOWN position)
GROUP
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
Preprogrammed Dip Switch
Settings for Remote Control
(Included on Back of Product
as a Reference)
598-1145-00
Control Descriptions
A or B GROUP: Allows each
Group Selection
Group Selection
channel to be used for 2 difLED Indicators
Buttons
ferent groups of receivers (for
a total of 16 channels). To
ALL ON
ALL OFF
choose Group A, press the
“A” button (the Group “A” inON
DIM
OFF
dicator will be on). To choose
Channel
Group B, press the “B” butLabel
ton (the Group “B” indicator
Guide
will be on).
Label Channels: Remove
clear plastic film from channel label guide by placing two
fingers on the plastic and
“pinching” the plastic. RePANIC
move card. Use the decals
(included) or write on the card
to label each channel. Replace card and plastic film.
ALL ON: Turns ON all light
Group Selection
fixtures programmed for either Group A or Group B. Either Group A or Group B LED indicator will light as
units are turned on. To perform this function, select either Group A or Group B
then press ALL ON. If lights are off or dimmed (where applicable) they will be
turned on full power.
ALL OFF: Turns OFF all light fixtures programmed for either Group A or Group
B. Either Group A or Group B LED indicator will light as units are turned off. To
perform this function, select either Group A or Group B then press ALL OFF. If
lights are on or dimmed (where applicable) they will be turned off.
PANIC: Turns ON all light fixtures programmed for either Group A or Group B.
Light fixtures within the selected group that have Flash capability will FLASH
when this command is received. Either Group A or Group B LED indicator will
light. ALL OFF will turn off all channels within the selected group and reset all light
fixtures to normal operating mode.
Channel ON: Turns ON all light fixtures that are configured to work with a
particular channel. To perform this function, press the ON button after selecting
the channel number desired (between 1 and 8). When ON is pressed, the A or
B LED will momentarily light.
Channel OFF: Turns OFF all light fixtures that are configured to work with a
particular channel. To perform this function, press the OFF button after selecting
the channel number desired (between 1 and 8). When OFF is pressed, the A or
B LED will momentarily light.
ALL OFF
FT
PY
ALL ON
598-1145-00
C
PY
Channel DIM: Dims all light fixtures that are equipped with the dimming feature
that are configured to work with a particular channel. To perform this function,
press the DIM button located by the channel number desired (between 1 and 8).
Pressing DIM repeatedly will toggle thru the different dim levels if the light fixture
is capable of more than one level of dim. Each time the DIM button is pressed,
the channel LED will momentarily light.
The receiver saves the last dim setting used. To recall the last dim setting, press
the DIM channel once.
Note: The receiver must be capable of dimming for the DIM button to work
properly.
Specifications
Range .......................................................................... Up to 100 feet (30.5 m)
Rated Voltage (2-AAA Batteries) .......................................................... 3 VDC
Troubleshooting Guide
SOLUTION
POSSIBLE CAUSE
Remote control does not
come on.
1. Batteries installed incor- 1. Install batteries according
to polarity markings inside
rectly.
remote control.
2. Replace batteries.
2. Batteries are dead.
Remote control will not operate receiver.
1. Dip switch settings on receiver do not match controller.
2. Wrong group or channel is
selected.
3. Signals from controller are
being blocked, or transmitter is out of range.
4. Batteries are weak.
FT
SYMPTOM
1. Check dip switch settings
on receiver.
2. Verify correct group and
channel are selected.
3. Check for metal objects that
could block the signal, or
reposition the transmitter.
4. Replace batteries.
Technical Service
(Do Not Send Products)
If you experience a problem, follow this guide. You may also want to visit our Web
site at: www.desatech.com. If the problem persists, call* for assistance at 1-800858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to:
DESA Specialty Products™
P.O. Box 90004, Bowling Green, KY 42102-9004
ATTN: Technical Service Specialty Products
* If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase.
No Service Parts Available for this Product
598-1145-00
Regulatory Information
PY
This device complies with Part 15 of the FCC Rules and RSS-210 of Industry
Canada. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The term “IC:” before the radio certification number only signifies that Industry
Canada technical specifications were met.
The user is cautioned that changes or modifications not expressly approved by
the party responsible for regulatory compliance could void the user’s authority
to operate the equipment.
TWO YEAR LIMITED WARRANTY
FT
This is a “Limited Warranty” which gives you specific legal rights. You may also have
other rights which vary from state to state or province to province.
For a period of two years from the date of purchase, any malfunction caused by
factory defective parts or workmanship will be corrected at no charge to you.
Batteries are not covered. To obtain a refund or a replacement, return the product
to the place of purchase.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or
negligence, light bulbs and other expendable items are not covered by this warranty.
Unauthorized service or modification of the product or of any furnished component
will void this warranty in its entirety. This warranty does not include reimbursement
for inconvenience, installation, setup time, loss of use, or unauthorized service.
This warranty covers only DESA Specialty Products™ assembled products and is
not extended to other equipment and components that a customer uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR
CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR
ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL
SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER
AND THERE SHALL BE NO LIABILITY ON THE PART OF DESA SPECIALTY
PRODUCTS™ FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR
PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not
allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. Retain receipt for warranty claims.
DESA Specialty Products™ reserves the right to discontinue products and to
change specifications at any time without incurring any obligation to incorporate
new features in products previously sold.
598-1145-00

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2003:06:13 09:15:59-05:00
Modify Date                     : 2003:06:13 11:54:16-05:00
Subject                         : 598-1136-00
Page Count                      : 4
Creation Date                   : 2003:06:13 14:15:59Z
Mod Date                        : 2003:06:13 14:15:59Z
Producer                        : Acrobat Distiller 5.0.5 for Macintosh
Author                          : Keith Peterson
Keywords                        : 
Metadata Date                   : 2003:06:13 14:15:59Z
Creator                         : Keith Peterson
Title                           : 598-1136-00
Description                     : 598-1136-00

EXIF Metadata provided by EXIF.tools