HeathCo 64WDB40TX Wireless Chime Control User Manual 595 5507 rev09

HeathCo LLC Wireless Chime Control 595 5507 rev09

Users Manual

DRAFT COPYLighted WirelessPush Button AccessoryThe Heath®/Zenith Wireless Push Button Accessory works with existingHeath®/Zenith jumper or dip switch systems.•Battery powered push button - No wires to run.•128 selectable codes allow more than one chime system in the samehouse.•LED lighted push bar in dark conditions.© 2002 DESA International 598-1137-00(Style may vary from illustration)Lighted Push Bar FeatureYour Heath®/Zenith wireless (battery operated) push button contains aLED (Light Emitting Diode) that will turn on in dark conditions so thepush button will be more visible for your guests. This patent (pending)technology and built-in photocontrol will allow the light intensity of thepush button LED to increase as the outdoor light conditions around thepush button decreases. The actual time and intensity that the LED isvisible will depend on the specific mounting environment of the pushbutton. In darker environments, such as garages, carports, or coveredporches, the LED will be visible a longer period of time each day oralways. In very well lighted environments, the LED will be visible for ashorter period of time each day or never. In nominal conditions the bat-teries will typically last 2 years.
-2-598-1137-00DRAFT COPY2. Set the push button jumpers to match the chime receivercode. See “Code and Tune Setting” section.1. Install lithium type CR2032 3 voltbatteries (included). Remove back ofcase by pushing in tab on bottom witha small screwdriver. Make sure batteryis oriented properly (see page 5).4. Mount push button.Use either screws or double sided tapeto mount push button.To mount with screws, remove back ofcase by pushing in tab on bottom with asmall screwdriver.Attach back of case to door jamb or wall.Snap front of push button on.When attaching push button using double sided tape, make surethe surface of the door jamb or wall is clean.3. Test range. Temporarily position push button where you wantit mounted. Press push button to verify chime and push buttonwork properly. If chime does not sound, see Troubleshooting.
-3-598-1137-00DRAFT COPYCode and Tune SettingsCode SettingsNote: Most installations will not require you to change anyjumpers on your chime and push button.WARNING: Disconnect chime unit from power source be-fore opening code access door. Close door and replacescrew before reconnecting to power.The push button and chime communicate by using a code thatcan be changed by removing and/or adding jumpers on boththe push button and chime. The code is factory set; however,there are 128 selectable codes that allow you to expand yoursystem and prevent outside interference. Other wireless prod-ucts may cause interference and the system may not functionproperly. Follow the instructions below for setting a new code.1. Unplug wireless chime (if applicable).2. Open the cases and locate the jumpers on both the push but-ton and chime (See illustration on page 5).3. The push button and chime both have eight different jumperlocations. The jumper positions 1 through 7 are used for set-ting the code.4. To change the code, add and/or remove jumpers as needed.It is recommended to only change one jumper at a time andthen check to see if system is functioning properly. Note: Jump-ers in positions 1 through 7 must be exactly the same for boththe push button and chime for this system to function.
-4-598-1137-00DRAFT COPYTune SettingsYour Heath®/Zenith wireless chime has different selectable tunes:Ding (one note), Ding-Dong (two note), or Westminster (eightnote) (Available on selected Heath®/Zenith chimes). The fac-tory setting is for the Ding-Dong tune (or Westminster, whenavailable). This tune can be changed by following the instruc-tions below.•Ding (one note tune)Push button: Add a jumper to location 8.•Ding-Dong (two note tune)Push button: Remove jumper from location 8.Chime: Remove jumper from location 8.•Westminster (Eight note tune) (Available on selected Heath®/Zenith chimes)Push button: Remove jumper from location 8.Chime: Add a jumper to location 8.Note: All models have both front and back door tune capabili-ties. You may purchase any Heath®/Zenith wireless push buttonfor a second entrance. We recommend the back door use theDing tune and the front door use the Ding-Dong tune (orWestminster tune, available on selected Heath®/Zenith chimes).Models that include two push buttons will come factory set forfront and back doors. Decals on the rear of the push button willindicate its setting.
-5-598-1137-00DRAFT COPYCR2032+1 2 3 4 5 6 7 812345678Inside PushButtonReplacing Push Button BatteriesInstall two lithium type CR2032 3 voltbatteries. See diagram inside pushbutton for correct battery orientation.* Code Settings1-7 Must MatchBoth PushButton andChimeRemovescrew to openaccess doorTune Setting (Notused on all models)Back ofChimeTuneSettingNote: Some models might requirethe use of tweezers to remove andreplace the jumpers.
-6-598-1137-00DRAFT COPYTroubleshootingChime does not sound:•Make sure push button and chime codes are the same (See pages 3,4, and 5).•Check orientation of push button battery (See page 5).•Check charge of push button and chime batteries (if applicable), re-place if necessary.Batteries seem OK, but the chime does not work when installed:•Do not mount chime or push button on metal or near metal studs.This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm)wood shims to move chime or push button off metal surface.•Concrete floors may reduce range. Move chime away from floor.•Try locating chime closer to push button.Push button light (LED) is “ON” or “OFF” all the time (see page 1).The range of the wireless chime can vary with location, temperatureand battery condition.
-7-598-1137-00DRAFT COPYNo Service Parts Available for this ProductTechnical Service(Do Not Send Products)If you experience a problem, follow this guide. You may also want to visitour Web site at: www.desatech.com. If the problem persists, call* forassistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You mayalso write* to:DESA International, Inc.P.O. Box 90004, Bowling Green, KY 42102-9004ATTN: Technical Service Specialty Products* If contacting Technical Service, please have the following informationavailable: Model Number, Date of Purchase, and Place of Purchase.Regulatory InformationThis device (6440TX) complies with Part 15 of the FCC Rules and RSS-210 ofIndustry Canada. Operation is subject to the following two conditions: (1) thisdevice may not cause harmful interference, and (2) this device must accept anyinterference received, including interference that may cause undesired opera-tion.The term “IC:” before the radio certification number only signifies that IndustryCanada technical specifications were met.The user is cautioned that changes or modifications not expressly approved by theparty responsible for regulatory compliance could void the user’s authority to oper-ate the equipment.
-8-598-1137-00DRAFT COPYYOUR HEATH®/ZENITH FIVE YEAR LIMITED WARRANTYThis is a “Limited Warranty” which gives you specific legal rights. You may alsohave other rights which vary from state to state or province to province.For a period of five year from the date of purchase, any malfunction caused byfactory defective parts or workmanship will be corrected at no charge to you.Batteries are not covered. To obtain a refund or a replacement, return theproduct to the place of purchase.Not Covered - Repair service, adjustment and calibration due to misuse, abuse ornegligence, light bulbs and other expendable items are not covered by this warranty.Unauthorized service or modification of the product or of any furnished componentwill void this warranty in its entirety. This warranty does not include reimbursementfor inconvenience, installation, setup time, loss of use, or unauthorized service.This warranty covers only Heath®/Zenith assembled products and is notextended to other equipment and components that a customer uses inconjunction with our products.THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATIONOR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FITFOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OFALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THECUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OFDESA FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUEN-TIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OFBUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Somestates or provinces do not allow the exclusion or limitation of incidental orconsequential damages, so the above limitation or exclusion may not apply toyou. Retain receipt for warranty claims.Heath®/Zenith reserves the right to discontinue and to change specifications at anytime without notice without incurring any obligation to incorporate new features inpreviously sold products.

Navigation menu