HeathCo 64WDB40TX Wireless Chime Control User Manual 595 5507 rev09

Download:
Mirror Download [FCC.gov]
Document ID	274719
Application ID	axOFEyHrfYmGe3SvzUw6yw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	36.68kB (458550 bits)
Date Submitted	2002-10-04 00:00:00
Date Available	2002-10-04 00:00:00
Creation Date	2002-09-04 11:34:44
Producing Software	Acrobat Distiller 5.0.5 for Macintosh
Document Lastmod	2002-09-04 11:34:44
Document Title	595-5507(rev09)
Document Creator	Adobe PageMaker 6.52

(Style may vary from illustration)
Lighted Wireless
Push Button Accessory
FT
The Heath®/Zenith Wireless Push Button Accessory works with existing
Heath®/Zenith jumper or dip switch systems.
• Battery powered push button - No wires to run.
• 128 selectable codes allow more than one chime system in the same
house.
• LED lighted push bar in dark conditions.
Lighted Push Bar Feature
Your Heath®/Zenith wireless (battery operated) push button contains a
LED (Light Emitting Diode) that will turn on in dark conditions so the
push button will be more visible for your guests. This patent (pending)
technology and built-in photocontrol will allow the light intensity of the
push button LED to increase as the outdoor light conditions around the
push button decreases. The actual time and intensity that the LED is
visible will depend on the specific mounting environment of the push
button. In darker environments, such as garages, carports, or covered
porches, the LED will be visible a longer period of time each day or
always. In very well lighted environments, the LED will be visible for a
shorter period of time each day or never. In nominal conditions the batteries will typically last 2 years.
© 2002 DESA International
598-1137-00
1. Install lithium type CR2032 3 volt
batteries (included). Remove back of
case by pushing in tab on bottom with
a small screwdriver. Make sure battery
is oriented properly (see page 5).
2. Set the push button jumpers to match the chime receiver
code. See “Code and Tune Setting” section.
3. Test range. Temporarily position push button where you want
it mounted. Press push button to verify chime and push button
work properly. If chime does not sound, see Troubleshooting.
FT
4. Mount push button.
Use either screws or double sided tape
to mount push button.
To mount with screws, remove back of
case by pushing in tab on bottom with a
small screwdriver.
Attach back of case to door jamb or wall.
Snap front of push button on.
When attaching push button using double sided tape, make sure
the surface of the door jamb or wall is clean.
-2-
598-1137-00
Code and Tune Settings
FT
Code Settings
Note: Most installations will not require you to change any
jumpers on your chime and push button.
WARNING: Disconnect chime unit from power source before opening code access door. Close door and replace
screw before reconnecting to power.
The push button and chime communicate by using a code that
can be changed by removing and/or adding jumpers on both
the push button and chime. The code is factory set; however,
there are 128 selectable codes that allow you to expand your
system and prevent outside interference. Other wireless products may cause interference and the system may not function
properly. Follow the instructions below for setting a new code.
1. Unplug wireless chime (if applicable).
2. Open the cases and locate the jumpers on both the push button and chime (See illustration on page 5).
3. The push button and chime both have eight different jumper
locations. The jumper positions 1 through 7 are used for setting the code.
4. To change the code, add and/or remove jumpers as needed.
It is recommended to only change one jumper at a time and
then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for both
the push button and chime for this system to function.
598-1137-00
-3-
D
FT
Tune Settings
Your Heath®/Zenith wireless chime has different selectable tunes:
Ding (one note), Ding-Dong (two note), or Westminster (eight
note) (Available on selected Heath®/Zenith chimes). The factory setting is for the Ding-Dong tune (or Westminster, when
available). This tune can be changed by following the instructions below.
• Ding (one note tune)
Push button: Add a jumper to location 8.
• Ding-Dong (two note tune)
Push button: Remove jumper from location 8.
Chime: Remove jumper from location 8.
• Westminster (Eight note tune) (Available on selected Heath®/
Zenith chimes)
Push button: Remove jumper from location 8.
Chime: Add a jumper to location 8.
Note: All models have both front and back door tune capabilities. You may purchase any Heath®/Zenith wireless push button
for a second entrance. We recommend the back door use the
Ding tune and the front door use the Ding-Dong tune (or
Westminster tune, available on selected Heath®/Zenith chimes).
Models that include two push buttons will come factory set for
front and back doors. Decals on the rear of the push button will
indicate its setting.
-4-
598-1137-00
Note: Some models might require
the use of tweezers to remove and
replace the jumpers.
Remove
screw to open
access door
Back of
Chime
12345678
Inside Push
Button
Tune
Setting
Replacing Push Button Batteries
Install two lithium type CR2032 3 volt
batteries. See diagram inside push
button for correct battery orientation.
598-1137-00
R 203
Tune Setting (Not
used on all models)
* Code Settings
1-7 Must Match
Both Push
Button and
Chime
FT
-5-
Troubleshooting
FT
Chime does not sound:
• Make sure push button and chime codes are the same (See pages 3,
4, and 5).
• Check orientation of push button battery (See page 5).
• Check charge of push button and chime batteries (if applicable), replace if necessary.
Batteries seem OK, but the chime does not work when installed:
• Do not mount chime or push button on metal or near metal studs.
This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm)
wood shims to move chime or push button off metal surface.
• Concrete floors may reduce range. Move chime away from floor.
• Try locating chime closer to push button.
Push button light (LED) is “ON” or “OFF” all the time (see page 1).
The range of the wireless chime can vary with location, temperature
and battery condition.
-6-
598-1137-00
Technical Service
(Do Not Send Products)
If you experience a problem, follow this guide. You may also want to visit
our Web site at: www.desatech.com. If the problem persists, call* for
assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may
also write* to:
DESA International, Inc.
P.O. Box 90004, Bowling Green, KY 42102-9004
ATTN: Technical Service Specialty Products
* If contacting Technical Service, please have the following information
available: Model Number, Date of Purchase, and Place of Purchase.
No Service Parts Available for this Product
Regulatory Information
FT
This device (6440TX) complies with Part 15 of the FCC Rules and RSS-210 of
Industry Canada. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
The term “IC:” before the radio certification number only signifies that Industry
Canada technical specifications were met.
The user is cautioned that changes or modifications not expressly approved by the
party responsible for regulatory compliance could void the user’s authority to operate the equipment.
598-1137-00
-7-
YOUR HEATH®/ZENITH FIVE YEAR LIMITED WARRANTY
FT
This is a “Limited Warranty” which gives you specific legal rights. You may also
have other rights which vary from state to state or province to province.
For a period of five year from the date of purchase, any malfunction caused by
factory defective parts or workmanship will be corrected at no charge to you.
Batteries are not covered. To obtain a refund or a replacement, return the
product to the place of purchase.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or
negligence, light bulbs and other expendable items are not covered by this warranty.
Unauthorized service or modification of the product or of any furnished component
will void this warranty in its entirety. This warranty does not include reimbursement
for inconvenience, installation, setup time, loss of use, or unauthorized service.
This warranty covers only Heath®/Zenith assembled products and is not
extended to other equipment and components that a customer uses in
conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION
OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT
FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF
ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE
CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF
DESA FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF
BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some
states or provinces do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to
you. Retain receipt for warranty claims.
Heath®/Zenith reserves the right to discontinue and to change specifications at any
time without notice without incurring any obligation to incorporate new features in
previously sold products.
-8-
598-1137-00

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2002:09:04 11:34:44-05:00
Modify Date                     : 2002:09:04 11:34:44-05:00
Subject                         : 595-5507(rev09)
Page Count                      : 8
Creation Date                   : 2002:09:04 16:34:44Z
Mod Date                        : 2002:09:04 16:34:44Z
Producer                        : Acrobat Distiller 5.0.5 for Macintosh
Author                          : 
Keywords                        : 
Metadata Date                   : 2002:09:04 16:34:44Z
Creator                         : ,
Title                           : 595-5507(rev09)
Description                     : 595-5507(rev09)

EXIF Metadata provided by EXIF.tools