HeathCo WLTX205 Wireless Door Chime Transmitter User Manual 208187 01A

HeathCo LLC Wireless Door Chime Transmitter 208187 01A

User Manual

DRAFT COPYTHANK YOU We appreciate the trust and condence you have placed in Hampton Bay through the purchase of this add on wireless door sensor. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Hampton Bay!USE AND CARE GUIDE ADD ON WIRELESS DOOR SENSORIllustrations may vary from actual unit.Safety Information1. Please read and understand this entire manual before attempting to assemble, install, or operate this sensor.WARNING: To prevent possible SERIOUS INJURY or DEATH never allow small children near batteries. If battery is swallowed, immediately notify a doctor.NOTE: The range of the wireless doorbell can vary with location, temperature, and battery condition.This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.The user is cautioned that changes or modications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the equipment.Care and Cleaning Use a dry cloth to clean the entry alert. Do not use cleaners or polishes. Do not use any uids on the entry alert.Pre-InstallationTOOLS REQUIREDPhillips screwdriver Small athead screwdriver Drill1/16” (1.5 mm) drill bit Safety gogglesHARDWARE INCLUDEDPart Description QuantityAA Jumper 1BB Screw - small 4CC Screw - large 2DD Double-sided tape 1PACKAGE CONTENTSPart Description QuantityASensor (with preinstalled battery) 1BMagnet 2CSpacer 2Installation1 Removing the battery tab Remove the back of the sensor (A) by pushing in the tab on the bottom with a small screwdriver (not included). Remove the orange battery tab from the sensor (A).2 Syncing the push button and doorbell Press and hold the “SYNC” button on the doorbell until the doorbell sounds a “Beep-Beep”. Press the button inside the sensor (A) within 30 seconds of pressing the doorbell “SYNC” button. Press the button inside the sensor again to activate the doorbell and ensure the sensor (A) and doorbell are synced.CR2032SYNC – PRESSAND RELEASE.RESET – HOLD 10 SECONDS.TUNE – HOLD 1 SECOND.303 Testing the sensor and doorbell Temporarily position the sensor (A) and magnet (B) where they will be mounted. Move the magnet (B) away from the sensor (A) to simulate a door being opened. The red LED should ash and the doorbell will sound “Beep-Beep”. If the doorbell does not sound, move the doorbell closer to the sensor (A) and test again.NOTE: Do not permanently mount the sensor until the sensor and doorbell are working properly.SYNC – PRESSAND RELEASE.RESET – HOLD 10 SECONDS.CHIME VOLUMETUNE – HOLD 1 SECOND.UPFRONT TRANS REARTYPE “C”TYPE “C”TYPE “C”4 Preparing to mount the sensorThe maximum gap between the sensor (A) and the magnet (B) is 1/2 in.. The arrows on the face of each component must be aligned and facing each other. Place the sensor (A) on the door frame and the magnet (B) beside the sensor (A) and ensure the arrows are aligned. If the magnet (B) is recessed, use the spacer (C) to ensure proper alignment.1/2" MaximumWarranty3-YEAR LIMITED WARRANTYWHAT IS COVEREDThis product is guaranteed to be free of factory defective parts and workmanship for a period of 3 years from date of purchase. Purchase receipt is required for all warranty claims.WHAT IS NOT COVEREDThis warranty does not include expendable items (such as light bulbs, batteries, etc.), repair service, adjustment and calibration due to misuse, abuse or negligence. Unauthorized service or modication of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components that a customer uses in conjunction with this product.Contact the Customer Service Team at 1-844-760-3644 or visit www.hamptonbay.com.Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday1-844-760-3644HAMPTONBAY.COMInstallation5 Mounting the sensorUse either the small screws (BB) or double-sided tape (DD) to mount the sensor (A). To mount with the small screws (BB), remove the back of sensor (A) by pushing in the tab on the bottom with a small screwdriver. Place the sensor (A) back against the mounting surface and mark the two screw holes. Drill two 1/16 in. pilot holes. Attach the sensor (A) back with the small screws (BB). Tighten securely and snap on the front of the sensor (A). When attaching the sensor (A) with double-sided tape (DD), remove paper from both sides of the double-sided tape (DD) and apply to a clean surface.6 Mounting the magnetUse the small screws (BB) (or the large screws (CC) if using the magnet spacer (C)) to mount the magnet (B). Remove the back of magnet (B) by pushing in the tab on the bottom of the magnet (B) with a small screwdriver. Place the magnet (B) back against the mounting surface and mark the two screw holes. Drill two 1/16 in. pilot holes. Attach the magnet (B) back with the small screws (BB). Tighten securely and snap on the front of the magnet (B). SpecicationsPower requirements Type 2032 3V battery (included) TroubleshootingProblem SolutionThe doorbell does not sound. Make sure batteries are installed according to the diagram inside the sensor and doorbell (if applicable).Check the charge of the sensor and doorbell batteries (if applicable) and replace if necessary.Make sure the plug-in doorbell has power (if applicable).Sensor and doorbell are not synced. Follow Step 2 in the Installation section to sync.The batteries seem okay, but the doorbell does not work after installation.Metal reduces transmission range. Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims to move the doorbell or sensor away from the metal surface.Concrete may reduce range. Move the doorbell away from the concrete surface.Locate the doorbell closer to the sensor.208187-01AAAAAAABAABBCCCABCBBCCDDItem #1000 000 000 Model #HB-7769-02ABBBB

Navigation menu