HeathCo WLTX205 Wireless Door Chime Transmitter User Manual 208187 01A

Download:
Mirror Download [FCC.gov]
Document ID	2661416
Application ID	28VLSwD4dh+BD7nZ7TQi4g==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	12.29kB (153636 bits)
Date Submitted	2015-06-29 00:00:00
Date Available	2015-06-29 00:00:00
Creation Date	2015-05-04 14:50:01
Producing Software	Acrobat Distiller 9.5.5 (Windows)
Document Lastmod	2015-05-04 14:50:01
Document Title	208187-01A.pdf
Document Creator	Adobe InDesign CS6 (Macintosh)
Document Author:	KPeterson

PACKAGE CONTENTS
Safety Information
USE AND CARE GUIDE
WARNING: To prevent possible SERIOUS INJURY or DEATH never allow small children near
batteries. If battery is swallowed, immediately notify a doctor.
ADD ON WIRELESS DOOR SENSOR
NOTE: The range of the wireless doorbell can vary with location, temperature, and battery
condition.
5 Mounting the sensor
Part
The user is cautioned that changes or modifications not expressly approved by the party
responsible for regulatory compliance could void the user’s authority to operate the
equipment.
Use a dry cloth to clean the entry alert.
Do not use cleaners or polishes.
Do not use any fluids on the entry alert.
Safety goggles
HARDWARE INCLUDED
1/16” (1.5 mm) drill bit
BB
DD
Description
 Remove the back of magnet (B) by
pushing in the tab on the bottom
of the magnet (B) with a small
screwdriver.
 Place the magnet (B) back against
the mounting surface and mark the
two screw holes.
 Drill two 1/16 in. pilot holes.
 Attach the magnet (B) back with
the small screws (BB). Tighten
securely and snap on the front of
the magnet (B).
SYNC – PRESS
AND RELEASE.
RESET – HOLD
10 SECONDS.
TUNE – HOLD
1 SECOND.
Power requirements
CR2032
BB
Type 2032 3V battery (included)
Troubleshooting
ME VO
HI
ME
LU
SYNC – PRESS
AND RELEASE.
RESET – HOLD
10 SECONDS.
TUNE – HOLD
1 SECOND.
Problem
Solution
The doorbell does not sound.
Make sure batteries are installed according
to the diagram inside the sensor and
doorbell (if applicable).
FRONT TRANS REAR
Check the charge of the sensor and doorbell
batteries (if applicable) and replace if
necessary.
Make sure the plug-in doorbell has power
(if applicable).
Preparing to mount the
sensor
The maximum gap between the sensor
(A) and the magnet (B) is 1/2 in.. The
arrows on the face of each component
must be aligned and facing each other.
Specifications
NOTE: Do not permanently mount the
sensor until the sensor and doorbell are
working properly.
AA
Part
TYPE “C”
 Temporarily position the sensor
(A) and magnet (B) where they will
be mounted.
 Move the magnet (B) away from
the sensor (A) to simulate a door
being opened. The red LED should
flash and the doorbell will sound
“Beep-Beep”.
 If the doorbell does not sound,
move the doorbell closer to the
sensor (A) and test again.
BB
Use the small screws (BB) (or the large
screws (CC) if using the magnet spacer
(C)) to mount the magnet (B).
30
the sensor and
3 Testing
doorbell
 To mount with the small screws
(BB), remove the back of sensor
(A) by pushing in the tab on the
bottom with a small screwdriver.
Place the sensor (A) back against
the mounting surface and mark the
two screw holes. Drill two 1/16 in.
pilot holes. Attach the sensor (A)
back with the small screws (BB).
Tighten securely and snap on the
front of the sensor (A).
 When attaching the sensor (A) with
double-sided tape (DD), remove
paper from both sides of the
double-sided tape (DD) and apply
to a clean surface.
6 Mounting the magnet
Drill
CC
1-844-760-3644
 Press and hold the “SYNC” button
on the doorbell until the doorbell
sounds a “Beep-Beep”.
 Press the button inside the sensor
(A) within 30 seconds of pressing
the doorbell “SYNC” button.
 Press the button inside the sensor
again to activate the doorbell and
ensure the sensor (A) and doorbell
are synced.
Small flathead screwdriver
Contact the Customer Service Team at 1-844-760-3644 or visit www.hamptonbay.com.
Questions, problems, missing parts?
Before returning to the store, call Hampton Bay Customer Service
8 a.m. - 5 p.m., CST, Monday - Friday
Spacer
TYPE “C”
This warranty does not include expendable items (such as light bulbs, batteries, etc.), repair
service, adjustment and calibration due to misuse, abuse or negligence. Unauthorized
service or modification of the product or of any furnished component will void this warranty
in its entirety. This warranty does not include reimbursement for inconvenience, installation,
setup time, loss of use, unauthorized service, or return shipping charges. This warranty
is not extended to other equipment and components that a customer uses in conjunction
with this product.
the push button and
2 Syncing
doorbell
This product is guaranteed to be free of factory defective parts and workmanship for a
period of 3 years from date of purchase. Purchase receipt is required for all warranty
claims.
WHAT IS NOT COVERED
Magnet
Use either the small screws (BB) or
double-sided tape (DD) to mount the
sensor (A).
UP
3-YEAR LIMITED WARRANTY
WHAT IS COVERED
FT
Phillips screwdriver
 Remove the back of the sensor
(A) by pushing in the tab on the
bottom with a small screwdriver
(not included).
 Remove the orange battery tab
from the sensor (A).
Warranty
Quantity
Sensor (with preinstalled battery)
1 Removing the battery tab
Pre-Installation
THANK YOU
We appreciate the trust and confidence you have placed in Hampton Bay through the
purchase of this add on wireless door sensor. We strive to continually create quality
products designed to enhance your home. Visit us online to see our full line of products
available for your home improvement needs. Thank you for choosing Hampton Bay!
Description
Installation
Care and Cleaning
TOOLS REQUIRED
This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Illustrations may vary from actual unit.
Installation
Please read and understand this entire manual before attempting to assemble, install,
or operate this sensor.
TYPE “C”
1.
Item #1000 000 000
Model #HB-7769-02
Sensor and doorbell are not synced. Follow
Step 2 in the Installation section to sync.
The batteries seem okay, but the
doorbell does not work after installation.
 Place the sensor (A) on the door
frame and the magnet (B) beside
the sensor (A) and ensure the
arrows are aligned.
 If the magnet (B) is recessed, use
the spacer (C) to ensure proper
alignment.
1/2" Maximum
Metal reduces transmission range. Use 1/4
in. to 1/2 in. (6 to 13 mm) wood shims to
move the doorbell or sensor away from the
metal surface.
Concrete may reduce range. Move the
doorbell away from the concrete surface.
Locate the doorbell closer to the sensor.
Quantity
AA
Jumper
BB
Screw - small
CC
Screw - large
DD
Double-sided tape
HAMPTONBAY.COM
208187-01A

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : KPeterson
Create Date                     : 2015:05:04 14:50:01-05:00
Modify Date                     : 2015:05:04 14:50:01-05:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2015:05:04 14:35:45-05:00
Creator Tool                    : Adobe InDesign CS6 (Macintosh)
Instance ID                     : uuid:9c6b115b-432c-4c9f-a647-5e5053b9c2d2
Original Document ID            : xmp.did:94A082175019E2118E12B8C3358D56E3
Document ID                     : xmp.id:34D052B90C2068118A6DCABB40817A28
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:32D052B90C2068118A6DCABB40817A28
Derived From Document ID        : xmp.did:4D522B7407206811822ADB5E791C7D9F
Derived From Original Document ID: xmp.did:94A082175019E2118E12B8C3358D56E3
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Macintosh)
History Changed                 : /
History When                    : 2015:05:04 14:35:42-05:00
Format                          : application/pdf
Title                           : 208187-01A.pdf
Creator                         : KPeterson
Producer                        : Acrobat Distiller 9.5.5 (Windows)
Trapped                         : False
Page Count                      : 1

EXIF Metadata provided by EXIF.tools