Heiman Technology HS1DSZ Smart Door Sensor User Manual

Shenzhen Heiman Technology Co.,Ltd. Smart Door Sensor

User Manual

Smart Door SensorUser  ManualTechnical ParametersFunction renderingsProduct Description*Please read the user manual carefully before operation.The guide picture is for reference only, please in kind prevail.This is a intelligent door sensor, adopts super low power Z-Wave  wireless  networking  technology,  makes  a  longer battery  life-span,  Feel  open  or  close  state  of  the  door  or window  through the near  and  separation  between  sensor and magnetic.  Dual sensor  design, makes  the  installation more  flexible  and  adaptable.  Products  are  suitable  for home,  villas,  factories,  shops,  warehouses,  office buildings,  banks,  room  and  other  places  of  safety prevention. Sensor MagnetNetworking IndicatorAlign  the  installation,  the  installation  distance  is  lessthan  15mm.  (The  magnet  part  can  be  installed  both sides of detector part)Tear  off  the  gummed  film,  stick  the  equipment  on  the required  area.Sensor  should  be  installed in  fixed area like door frame, magnet  can be installed in active  area like door plank, this picture for reference only.Click the “add” button to enter the networking mode.Long press the networking button,then power on (put intobattery),ID code is clear and recover to factory setting.Restore factory settingsConnecting  network:  According  to  the  APP  tip,  press  the device  networking  hole  for  3  times  in  1.5 seconds,  then the green  LED  flashes  quickly  (connecting  network  within    30 seconds),  and  “networking  succeed  “  will  be  displayed  on app interface.Disconnecting  network:  Click  the  “delete  device”  button  on APP,  then  quick  press  networking  hole  for  3  times  in  1.5 seconds,  green  LED  flashes  for  6  times,  disconnecting network succeed.Anti-tamper KeyBattery replacementStep 1 Step 2Please  change  the  battery  according  to  negative and positive of the battery.Please  deal  with  waste  batteries  correctly  for environmental protection.Step 3 Step 4 Step 5 Step 6+-+-++--++--Remove insulator make device on power.Install sensors into the bracket.1. DC3V(2 AAA battery)2≤5uA3≤35mA4>15mmZ-Wave    6≥70 metres                                                    9 16.5 mmWorking Voltage: Static CurrentAlarm CurrentDetecting DistanceNetworking Ad-Hoc NetworkWireless Networking Distancein the open areaWorking EnvironmentWorking Humidity Maximum 95%RHDetector DimensionMagnet dimension×( )℃×× ×...5..7. -10℃ ~ +508.. 76×36.610. 76 13.9 16.5 mm: : : : : : : : : networkingbutton12 3 4 5Statement*Instruction is for reference only, please prevail in kind.*Because of the updating of the technology, the final interpretation right owned by factory, if there are any inconformities when using this products under this instruction.6 7 8 9 10 11HS1DS-Z
  FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •  Reorient or relocate the receiving antenna. •  Increase the separation between the equipment and receiver. •  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •  Consult the dealer or an experienced radio/TV technician for help.  Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.  This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu