Heiman Technology HS1DSZ Smart Door Sensor User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3381767
Application ID	+NCtuj6zyWTLLjNfCHvhsw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	14.69kB (183666 bits)
Date Submitted	2017-05-08 00:00:00
Date Available	2017-05-08 00:00:00
Creation Date	2016-11-30 06:46:27
Producing Software	Corel PDF Engine Version 14.0.0.653
Document Lastmod	0000-00-00 00:00:00
Document Title	601010835 HS1DS-Z智能门磁中性英文说明书.cdr
Document Creator	CorelDRAW
Document Author:	USER

Smart Door Sensor
User Manual
Step 1
3.Alarm Current: ≤35mA
Product Description
4.Detecting Distance: ＞15mm
5.Networking: Z-Wave Ad-Hoc Network
6.Wireless Networking Distance: ≥70 metres
Networking Indicator
7.Working Environment: -10℃ ～ +50℃
Function renderings
2.Static Current: ≤5uA
（in the open area）
networking
button
Step 2
1.Working Voltage: DC3V（2×AAA battery）
Technical Parameters
HS1DS-Z
This is a intelligent door sensor, adopts super low power ZWave wireless networking technology, makes a longer
battery life-span, Feel open or close state of the door or
window through the near and separation between sensor
and magnetic. Dual sensor design, makes the installation
more flexible and adaptable. Products are suitable for
home, villas, factories, shops, warehouses, office
buildings, banks, room and other places of safety
prevention.
8.Working Humidity: Maximum 95%RH
9.Detector Dimension: 76×36.6×16.5 mm
10.Magnet dimension: 76×13.9×16.5 mm
Sensor
*Please read the user manual carefully before operation.
The guide picture is for reference only, please in kind prevail.
Step 3
Magnet
Remove insulator make device on power.
Step 4
Step 5
Click the “add” button to enter the networking mode.
Step 6
Anti-tamper Key
+ -
Connecting network: According to the APP tip, press the
device networking hole for 3 times in 1.5 seconds, then the
green LED flashes quickly (connecting network within 30
seconds), and “networking succeed “ will be displayed on
app interface.
Disconnecting network: Click the “delete device” button on
APP, then quick press networking hole for 3 times in 1.5
seconds, green LED flashes for 6 times, disconnecting
network succeed.
Align the installation, the installation distance is less
than 15mm. (The magnet part can be installed both
sides of detector part)
Tear off the gummed film, stick the equipment on the
required area.Sensor should be installed in fixed area
like door frame, magnet can be installed in active area
like door plank, this picture for reference only.
Long press the networking button,then power on (put into
battery),ID code is clear and recover to factory setting.
Install sensors into the bracket.
10
Battery replacement
Restore factory settings
- +
- +
+ Please change the battery according to negative
and positive of the battery.
Please deal with waste batteries correctly for
environmental protection.
Statement
*Instruction is for reference only, please prevail in kind.
*Because of the updating of the technology, the final interpretation right
owned by factory, if there are any inconformities when using this products
under this instruction.
11
FCC Warning:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved
by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Creation Date--Text             : 
Producer                        : Corel PDF Engine Version 14.0.0.653
Mod Date--Text                  : 
Format                          : application/pdf
Creator                         : USER
Title                           : 601010835 HS1DS-Z智能门磁中性英文说明书.cdr
Creator Tool                    : CorelDRAW
Modify Date                     : 2017:04:26 23:00:26+08:00
Metadata Date                   : 2017:04:26 23:00:26+08:00
Document ID                     : uuid:6e2b50a3-fbba-4cee-8efb-a4a19e87e7f6
Instance ID                     : uuid:9d2dc4aa-6333-4a87-8d8d-caa238bba068
Page Count                      : 2
Create Date                     : D:20161130064627Z
Author                          : USER

EXIF Metadata provided by EXIF.tools