Hewlett Packard Enterprise 651 Aruba 651-US, OAW-4306GW-US User Manual Greanche HW IG

Download:
Mirror Download [FCC.gov]
Document ID	1111384
Application ID	vLsHmRpB8MhIWfUDUKZOTQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	76.24kB (952940 bits)
Date Submitted	2009-05-15 00:00:00
Date Available	2009-05-15 00:00:00
Creation Date	2009-05-14 10:58:31
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2009-05-14 13:18:19
Document Title	Greanche_HW_IG.book
Document Creator	FrameMaker 8.0
Document Author:	dmontgomery

CONSOL
LINK/
ACT
LINK/
ACT
POE
1000
LINK/
ACT
LINK/
ACT
Installation Guide
Aruba 650 Series
Controller
Copyright
© 2009 Aruba Networks, Inc. All rights reserved.
Trademarks
Aruba Networks® is a registered trademark, and Mobility Management System, RFprotect®, and Bluescanner are trademarks of Aruba
Networks, Inc.
All other trademarks or registered trademarks are the property of their respective holders.
Specifications are subject to change without notice.
Legal Notice
The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors' VPN
client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba
Networks, Inc. from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those
vendors.
Warranty
This hardware product is protected by the standard Aruba warranty of one year parts/labor. For more information, refer to the
ARUBACARE SERVICE AND SUPPORT TERMS AND CONDITIONS.
Altering this device (such as painting it) voids the warranty.
www.arubanetworks.com
1322 Crossman Avenue
Sunnyvale, California 94089
Phone: 408.227.4500
Fax 408.227.4550
May 2009 | 0510572-01
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Contents
Preface...................................................................................................... 5
General Overview ..................................................................................................5
Related Documentation .........................................................................................5
Contacting Aruba Networks ..................................................................................6
Chapter 1
Aruba 650 Series Hardware Overview ................................................... 7
About the Aruba 650 Series Controller..................................................................7
Minimum Software Requirements .........................................................................7
Package Checklist .................................................................................................7
Hardware Model Overview ....................................................................................8
Front View .......................................................................................................8
1000Base-X (SFP) Ports ...........................................................................8
10/100/1000Base-T Gigabit Ethernet Ports .............................................8
Serial Console Port...................................................................................9
Serial Console Port Adaptor ...................................................................10
USB Ports ...............................................................................................10
Media Eject Button .................................................................................10
Rear View ......................................................................................................11
AC Power Socket ...................................................................................11
ExpressCard Slot....................................................................................11
Antennae Interfaces (Aruba 651 Only) ....................................................11
LED Status Indicators..........................................................................................11
Chapter 2
Aruba 650 Series Installation ................................................................ 13
Installation ...........................................................................................................13
Pre-Installation Requirements.......................................................................13
Physical Installation.......................................................................................13
Rack Mounting .......................................................................................13
Tabletop Deployment .............................................................................15
Initial Setup and Network Connectivity.........................................................15
Removal...............................................................................................................15
Appendix A
Specifications, Safety, & Compliance.................................................. 17
Specifications ......................................................................................................17
Physical Specifications .................................................................................17
Power Specifications ....................................................................................17
Operating Specifications...............................................................................17
Storage Specifications ..................................................................................17
Wireless Radio Specifications (651 Internal AP) ...........................................17
AP type ...................................................................................................17
Operating Frequency ..............................................................................17
Available Channels .................................................................................17
Modulations ............................................................................................17
Transmit Power.......................................................................................18
Association Rates (Mbps).......................................................................18
802.11n High-Throughput (HT) Support.................................................18
802.11n Packet Aggregation ..................................................................18
Antenna (Aruba 651 Internal AP) ...................................................................18
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Contents | 3
Safety and Regulatory Compliance .....................................................................19
FCC Class B Device......................................................................................19
Aruba 650......................................................................................................19
Aruba 651......................................................................................................19
Proper Disposal of Aruba Equipment ..................................................................20
Waste of Electrical and Electronic Equipment ..............................................20
European Union RoHS ..................................................................................20
China RoHS ..................................................................................................20
4 | Contents
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Preface
This preface includes the following information:
An overview of the contents of this manual
A list of related documentation for further reading
Aruba support and service information
General Overview
Chapter 1, “Aruba 650 Series Hardware Overview” on page 7 provides a detailed hardware overview of the Aruba 650
Series.
Chapter 2, “Aruba 650 Series Installation” on page 13 provides rack mounting and installation instructions.
Appendix A, “Specifications, Safety, & Compliance” on page 17 includes product technical specifications, safety, and
regulatory compliance information.
Related Documentation
The following documentation are referred to in this guide and are considered components of the complete documentation
set needed for a successful installation and management of an Aruba Mobility Controller.
ArubaOS Quick Start Guide
ArubaOS User Guide
Aruba Mobility Management System User Guide
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Preface | 5
Contacting Aruba Networks
Web Site Support
Main Site
http://www.arubanetworks.com
Support Site
https://support.arubanetworks.com
Software Licensing Site
https://licensing.arubanetworks.com/login.php
Wireless Security Incident
Response Team (WSIRT)
http://www.arubanetworks.com/support/wsirt.php
Support Emails
Americas and APAC
support@arubanetworks.com
EMEA
emea_support@arubanetworks.com
WSIRT Email
Please email details of any security
problem found in an Aruba product.
wsirt@arubanetworks.com
Telephone Support
Aruba Corporate
+1 (408) 227-4500
FAX
+1 (408) 227-4550
Support
United States
800-WI-FI-LAN (800-943-4526)
Universal Free Phone Service Number
(UIFN): Australia, Canada, China,
France, Germany, Hong Kong, Ireland,
Israel, Japan, Korea, Singapore, South
Africa, Taiwan, and the UK.
+800-4WIFI-LAN (+800-49434-526)
All Other Countries
+1 (408) 754-1200
6 | Preface
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Chapter 1
Aruba 650 Series Hardware
Overview
About the Aruba 650 Series Controller
The Aruba 650 Series controller is an enterprise-class, wireless LAN controller. This controller connects, controls, and
integrates wireless Access Points (APs) and Air Monitors (AMs) into a wired LAN system.
Aruba 650 Series controller
The Aruba 650 is capable of supporting up to 16 external, campus connected APs.
„
650: no built-in external AP support; optional Aruba AP upgrade licenses are available.
„
650-8: includes built-in campus connected AP support for up to 8 APs; optional Aruba AP upgrade licenses are
available.
The Aruba 651 is capable of supporting up to 16 external, campus connected APs in addition to its single, internal AP.
„
651-1: includes a single, internal AP; no built-in external AP support; optional Aruba AP upgrade licenses are available.
„
651-9: includes a single, internal AP, as well as, built-in campus connected AP support for up to 8 APs; optional Aruba
AP upgrade licenses are available.
NOTE
Feature related AP licenses are counted independently and in addition to the Aruba AP upgrade
licenses. Contact your Aruba sales representative for complete details regarding software licensing
options and support capacity.
Minimum Software Requirements
The Aruba 650 Series controller requires ArubaOS 3.4.0 or later.
ArubaOS software builds prior to version 3.4.0 does not support the Aruba 650 Series controller. If your network currently
runs a software build prior to 3.4.0, you must upgrade the software on your master and local controllers to 3.4.0 or later prior
to installing an Aruba 650 Series Mobility Controller in your existing network.
NOTE
The master controller, its redundant master controller, and all of its local controllers must run on the
same code of ArubaOS. Once you upgrade your network and install an Aruba 650 Series Mobility
Controller into your network, verify that the software version on your controller matches the rest of
your network. If the code shipped on the controller is prior to the version that you upgraded your
network to, you must upgrade the code on the controller to match the rest of the network.
Package Checklist
Aruba 650 Series Mobility Controller
AC Power Cord (country-specific)
Rack Mount Brackets with Hardware (for rack mounting)
Left Side Bezel (not installed)
Right Side Bezel (not installed)
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Aruba 650 Series Hardware Overview | 7
z
Rubber Feet (for table top deployments)
Flat Serial Cable (RJ-45)
Serial Cable Port Adapter (RJ-45 to DB9)
ArubaOS Software Documentation CD
Dual-band, High-gain, Omni-directional Detachable Antennae (3x)
ArubaOS Quick Start Guide
End User License Agreement (EULA)
NOTE
Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the
carton, including the original packing materials. Use these materials to repack and return the unit to
the supplier if needed.
Hardware Model Overview
Front View
Figure 1 Aruba 650 Series Front View
10/100/1000Base-T
Gigabit Ethernet Ports
USB ports
LE
CONSO
Serial Console Port
LINK
ACT
LINK
ACT
POE
1000
LINK
ACT
LINK
ACT
Media Eject Button
1000Base-X (SFP) Ports
10/100/1000Base-T Gigabit
Ethernet Ports with PoE
1000Base-X (SFP) Ports
There are two 1000Base-X ports for fiber connectivity only and are intended for use with Aruba SFPs (mini-GBICs).
To purchase compatible SFP modules, contact your Aruba sales representative for details and assistance.
NOTE
Aruba tests and supports Aruba optics within their controller system. Third party optics are not
tested or supported; therefore, Aruba does not guarantee proper functionality of third party optics
when used in an Aruba system.
10/100/1000Base-T Gigabit Ethernet Ports
There are six 10/100/1000Base-T Gigabit Ethernet (RJ-45) ports on the Aruba 650 Series. Gigabit Ethernet uses all eight wires
and each pair is used in a bi-directional fashion, meaning the same pairs are used for both data transmission and reception.
8 | Aruba 650 Series Hardware Overview
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Figure 2 illustrates the CAT-5 pin-out found on an RJ-45 connector. The CAT-5 pin-out pairs the following pins on a 10/100/
1000Base-T Gigabit Ethernet port: 1/2, 3/6, 4/5, and 7/8.
Figure 2 Gigabit Ethernet Port Pin-Out
1000Base-T Gigabit
Ethernet Port
RJ-45 Female
Pin-Out
Signal Name
Function
BI_DA+
BI_DABI_DB+
BI_DC+
BI_DCBI_DBBI_DD+
BI_DD-
Bi-directional pair +A
Bi-directional pair -A
Bi-directional pair +B
Bi-directional pair +C
Bi-directional pair -C
Bi-directional pair -B
Bi-directional pair +D
Bi-directional pair -D
Serial Console Port
A serial console port is provided for connection to a terminal, allowing for direct local management. The port’s RJ-45 female
connector accepts an RS-232 serial cable with a male connector.
Figure 3 Serial Console Port Pin-Out
Serial
Console Port
RJ-45 Female
Pin-Out
Direction
Input
Output
TxD
GND
GND
RxD
Communication settings for the serial port are indicated in Table 1.
Table 1 Console Terminal Settings
Baud Rate
Data Bits
Parity
Stop Bits
Flow Control
9600
None
None
Do not connect an AP to the serial console port. The serial console port is compatible only with RS232 devices. Non-RS-232 devices, such as APs, are not supported.
CAUTION
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Aruba 650 Series Hardware Overview | 9
Serial Console Port Adaptor
A modular adaptor can be used to convert the RJ-45 (female) connector to a DB9 (male) connector. Refer to Figure 4 for
complete details.
Figure 4 RJ-45 (female) to DB9 (male) Modular Adaptor Conversion
Internal
Connections
RJ-45 Female
Pin-Out
TxD
GND
RxD
Direction
Input
Output
RJ-45
TxD
GND
RxD
DB-9 Male
Pin-Out
DB-9
Ground
RxD
TxD
Direction
Input
Output
USB Ports
The Aruba 650 Series has four USB 2.0 interfaces. These interfaces allow the use of EVDO/HSPDA modem, flash or disk
storage devices, or a printer
Media Eject Button
The Aruba 650 Series is equipped with a media eject button, which allows users to eject storage devices safely and place the
system in standby. Pushing the media eject button changes the state of the Aruba 650 Series; the table below describes the
states and LED behaviors associated with use of the media eject button.
Table 2 Media Eject Button LED Behavior
Initial State
LED State
Action
Status LED
Function
LED Action
Completed
NAS Media Operational
Green-solid
Press and hold
media eject button
for 1 to 5 seconds
only
Amber-flashing
Un-mount all NAS
media
Amber-solid
NAS Media Unmounted
Amber-solid
Press and hold
media eject button
for 1 to 5 seconds
only
Amber-flashing
Mount all attached
NAS devices, and
return to fully
functional
operation
Green-solid
Operational
Green-solid
Press and hold
media eject button
for more than 5
seconds only
Red-flashing
Controller goes
into Standby
Red-solid
Operating with NAS
Media un-mounted
Amber-solid
Press and hold
media eject button
for more than 5
seconds only
Red-flashing
Controller goes
into Standby
Red-solid
Standby
Red-solid
Press media eject
button
Amber-flashing
Controller wake-up
Green-solid
10 | Aruba 650 Series Hardware Overview
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Rear View
Figure 5 Aruba 650 Series Rear View (651 Shown)
Antennae Interfaces
(651 Only)
Slot
ExpressCard Slot
AC Power Socket
AC Power Socket
The Aruba 650 Series supports integrated AC powering and the AC power socket on the rear of the unit is for use with an AC
power cord (country-specific). Refer to "Power Specifications" on page 17 for power specification details.
ExpressCard Slot
The Aruba 650 Series is equipped with one ExpressCard slot.
Antennae Interfaces (Aruba 651 Only)
The Aruba 651 is equipped with an internal Access Point (AP). This AP can operate in 2.4 GHz and 5 GHz bands, in a/b/g or n
modes. Each appliance has three RP-SMA interfaces to attach the antennae included in this kit.
LED Status Indicators
Table 3 Aruba 600 Series LED Status Indicators
LED
Label
Function
Indicator
Status
Power
POWER
Input Power Status Indicator
On (Solid Green)
Power on
Off
No Power
On (Solid Green)
Device is operational
On (Solid Red)
Device failed or is in Standby
On (Solid Amber)
Device is loading software
Off
No power
Status
STATUS
Module Status Indicator
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Aruba 650 Series Hardware Overview | 11
Table 3 Aruba 600 Series LED Status Indicators
LED
Label
Function
Indicator
Status
1000Base-X Ports (SFP)
LNK/ACT
Link Status Indicator
On (Solid Green)
Link has been established
On (Flashing Green)
Port is transmitting or receiving
data
Off
No link on port
On (Solid Green)
Link has been established
On (Flashing Green)
Port is transmitting or receiving
data
Off
No link on port
On (Solid Green)
1000 Mbps
Off
10/100 Mbps
On (Solid Green)
Link has been established
On (Flashing Green)
Port is transmitting or receiving
data
Off
No link on port
On (Solid Green)
PoE is being provided
On (Solid Amber)
The attached device has
requested PoE, but PoE is not
being provided by the port
Off
PoE is not being provided
On (Solid Amber)
Radio enabled in WLAN mode
On (Solid Green)
Radio enabled in 802.11n
mode
On (Flashing Amber)
Air monitor mode
Off
Radio is disabled
10/100/1000Base-T Ports
LNK/ACT
1000
10/100/1000Base-T Ports
with PoE
LINK/ACT
PoE
802.11 a/b/g/n AP
(Aruba 651 Only)
WLAN
12 | Aruba 650 Series Hardware Overview
Link/Activity Status Indicator
Interface Speed
Link/Activity Status Indicator
PoE Status Indicator
AP Status
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Chapter 2
Aruba 650 Series Installation
Installation
Pre-Installation Requirements
The following tools and equipment are required for installation of an Aruba 650 Series controller.
Rack Mount Bracket (x2, not used for tabletop installation)
6-32 x 1/4” Phillips Flat Head Screws (4x, included with rack mount brackets)
12-24 x 5/8” Phillips Flat Head Screws (4x, 19-inch (48.26 cm) rack system mount screws).
Suitable Screwdrivers for both screw types.
AC Power Cord (country-specific)
Left and right side bezels (not used for rack mounting)
Physical Installation
Rack Mounting
To install an Aruba 650 Series controller into a 19-inch (48.26 cm) rack system:
1. Place a rack mount bracket over the mounting holes on one side of the controller (see Figure 6).
2. Secure the bracket to the controller using two 6-32 x 1/4” phillips flat head screws and a suitable screwdriver.
3. Repeat these steps on the opposite side of the controller.
Figure 6 Rack Mount Brackets
Rack Mount Bracket (2x)
OLE
CONS
LINK
ACT
LINK
ACT
POE
1000
LINK
ACT
LINK
ACT
6-32 x 1/4” Phillips Flat Head Screws
(4x, 2x per bracket)
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Aruba 650 Series Installation | 13
4. Mount the controller within your organization’s rack system using four 12-24 x 5/8” phillips flat head screws and suitable
screwdriver (see Figure 7).
Figure 7 Rack Mount Installation
Standard 19-inch
Rack System
SOLE
CON
LINK
ACT
LINK
ACT
POE
1000
LINK
ACT
LINK
ACT
12-24 x 5/8”
Phillips Flat Head Screws
(4x, 2x per bracket)
5. Leave a minimum of four inches (10cm) of space on the left and right side of the unit for proper air flow and ventilation
(see Figure 8).
6. Leave additional space in front and back of the unit to access power cords, network cables, and LED status indicators
(see Figure 8).
Figure 8 Air Flow Requirements
Keep Clear for
Air Intake
Keep Open for
Easy Access
LE
CONSO
Keep Clear
for Air Exhaust
LINK
ACT
LINK
ACT
POE
1000
LINK
ACT
LINK
ACT
Keep Open for
Easy Access
14 | Aruba 650 Series Installation
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
7. Connect the AC power cord (country-specific) to the rear of the unit.
8. Plug the opposite end of the power cord into an electrical outlet to power the controller.
NOTE
Aruba 650 Series controller does not have a switch for turning power to the unit on or off. Power to
the unit is controlled by connecting or disconnecting the plug on the power cord to or from an
electrical outlet.
Tabletop Deployment
To deploy an Aruba 650 Series controller on a flat surface, such as a tabletop:
1. Insert the four rubber mounting feet to the bottom of the unit.
2. Attach side bezels by snapping them into place.
3. Place the unit on a hard flat surface.
Initial Setup and Network Connectivity
Once the physical installation is complete, run the initial setup on the controller to configure the IP address and other basic
system information. For complete details and instructions, refer to the ArubaOS Quick Start Guide for the software version
installed on your controller.
Removal
To remove an Aruba 650 Series controller from a 19-inch (48.26 cm) rack system:
1. Disconnect the power to the controller by unplugging the power cord from the electrical outlet.
2. Loosen the four rack mount screws securing the controller to your organizations rack system.
3. Remove the controller from the rack system.
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Aruba 650 Series Installation | 15
16 | Aruba 650 Series Installation
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Appendix A
Specifications, Safety, &
Compliance
Specifications
Physical Specifications
Device Dimensions (without rack mount brackets)
Height 1.5˝ (38 mm)
Width 13.6˝ (346 mm)
Depth 8.9˝ (226 mm)
Power Specifications
AC Input Voltage: 100-240 V, Universal Input
AC Input Frequency: 50-60 Hz
Maximum power consumption: 126 Watts
Power over Ethernet total capacity: 78 Watts
Power over Ethernet capacity per port: 19.5 Watts
Operating Specifications
Operating Temperature Range: 0°C to 40°C (32°F to 104°F)
Operating Humidity Range: 5% to 95% (RH), non-condensing
Storage Specifications
Storage Temperature Range: 0°C to 50°C (32°F to 122°F)
Storage Humidity Range: 5% to 95% (RH), non-condensing
Wireless Radio Specifications (651 Internal AP)
AP type
2x3, 3x3 Multiple-In, Multiple-Out (MIMO)
Operating Frequency
2.4-2.5 GHz or 5.150–5.950 GHz
Available Channels
Mobility Controller-managed, dependent upon configured regulatory domain
Modulations
802.11b: Direct-Sequence Spread-Spectrum (DSSS)
802.11a/g: Orthogonal Frequency Division Multiplexing (OFDM)
802.11n: 802.11n draft 2.0
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Specifications, Safety, & Compliance | 17
Transmit Power
Configurable in increments of 0.5 dBm
Association Rates (Mbps)
802.11b: 11, 5.5, 2, 1 with automatic fallback
802.11a/g: 54, 48, 36, 24, 18, 12, 9, 6 with automatic fallback
802.11n: MCS0 - MCS15 (6.5Mbps - 300Mbps)
802.11n High-Throughput (HT) Support
HT 20
HT 40
802.11n Packet Aggregation
A-MPDU
A-MSDU
Antenna (Aruba 651 Internal AP)
Three RP-SMA interfaces for external antenna support (supports up to 3x3 MIMO with spatial diversity)
Three AP-ANT-1B omni-directional dual-band antennas included
18 | Specifications, Safety, & Compliance
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Safety and Regulatory Compliance
Aruba provides a multi-language document containing country specific restrictions and additional safety and regulatory
information for all Aruba hardware products. The Aruba Safety and Regulatory Addendum can be viewed or downloaded
from the following location: www.arubanetworks.com/safety_addendum.
CLASS 1
LASER PRODUCT
Use of controls or adjustments of performance or procedures other than those specified in this
manual may result in hazardous radiation exposure.
CAUTION
This product complies with 21 CFR Chapter 1, Subchapter J, Part 1040.10, and IEC 60825-1: 1993, A1: 1997, A2: 2001, IEC
60825-2: 2000.
For continued compliance with the above laser safety standards, only approved Class 1 modules from our approved vendors
should be installed in Aruba products.
FCC Class B Device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a
minimum distance of 13.78 inches (35 cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in the
5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with
co-channel Mobile Satellite Systems.
Aruba 650
EN 55022 Class B
EN 55024
IEC/EN 60950
CE Marking
cTUVus Marked
CB Scheme Certified
Aruba 651
FCC 15.247/15.407
EU R&TTE Directive 1999/5/EC (EN 300 328, EN 301 893, EN 301 489)
EU LV Directive 2006/95/EC
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide
Specifications, Safety, & Compliance | 19
z
IEC/EN 60950
CE Marking
cTUVus Marked
CB Scheme Certified
For a complete list of Country Specific Regulations please speak with your Aruba Representative.
Proper Disposal of Aruba Equipment
For the most current information on Global Environmental Compliance and Aruba products please see our website at
www.arubanetworks.com.
Waste of Electrical and Electronic Equipment
Aruba products at end of life are subject to separate collection and treatment in the EU Member States,
Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out
wheelie bin). The treatment applied at end of life of these products in these countries shall comply with
the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and
Electronic Equipment (WEEE).
European Union RoHS
Aruba products also comply with the EU Restriction of Hazardous Substances Directive 2002/95/EC
(RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical
and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead
(including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba
products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies).
Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this Directive.
China RoHS
Aruba products also comply with China environmental declaration requirements and are labeled with the
“EFUP e” label shown at the left.
20 | Specifications, Safety, & Compliance
Aruba 650 Series Multi-Service Mobility Controller | Installation Guide

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Creator Tool                    : FrameMaker 8.0
Modify Date                     : 2009:05:14 13:18:19-07:00
Create Date                     : 2009:05:14 10:58:31Z
Metadata Date                   : 2009:05:14 13:18:19-07:00
Format                          : application/pdf
Title                           : Greanche_HW_IG.book
Creator                         : dmontgomery
Document ID                     : uuid:85fb5373-2808-49f8-b598-64a4929f50d0
Instance ID                     : uuid:19efa9b3-844a-4db6-8cd7-a9a334827dee
Page Count                      : 20
Author                          : dmontgomery

EXIF Metadata provided by EXIF.tools