Hewlett Packard Enterprise APEX0102 Access Point User Manual AP 277 IG Rev 01

Aruba Networks, Inc. Access Point AP 277 IG Rev 01

Contents

User Manual

AP-277 Outdoor Access PointInstallation Guide0511689-01 | September 2014 1The Aruba AP-277 is an environmentally hardened, outdoor rated, dual-radio IEEE 802.11ac wireless access point. This access point use MIMO (Multiple-in, Multiple-out) technology and other high-throughput mode techniques to deliver high-performance, 802.11ac 2.4 GHz and 5 GHz functionality while simultaneously supporting existing 802.11a/b/g/n wireless services. The AP-277 access point works only in conjunction with an Aruba Controller. AP-277 OperationsWireless transceiverWireless access point (IEEE 802.11 a/b/g/n/ac)Wireless air monitor (IEEE 802.11 a/b/g/n/ac)Protocol-independent networking functionalityCompatibility with IEEE 802.3at PoECentral management configuration and upgrades with an Aruba Controller.Guide Overview“AP-277 Hardware Overview” on page3 provides a detailed hardware overview of the AP-277.“Before You Begin” on page5 provides key questions to ask and items to consider when deploying an outdoor wireless network.“Installing the AP” on page7 describes the multi-step process for a successful installation and deployment of the AP-277.“Safety and Regulatory Compliance” on page16 provides an overview of safety and regulatory compliance information.Package ContentsAP-277 Access PointCable Glands x2USB Console CableCopper Lug x1M4 x 6 Screw x1Installation Guide (this document)The weatherproof caps for Ethernet, Console, and power interfaces are connected to the AP, not loose in the package.Mounting kits for use with the AP-270 Series access points are sold separately. Contact your Aruba sales representative for details.
2AP-277 Outdoor Access Point | Installation GuideInform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed.
AP-277 Outdoor Access Point | Installation Guide 3AP-277 Hardware OverviewFigure 1 AP-277 Front View Figure 2 AP-277 Rear ViewLED The AP-277 is equipped with one LED that indicates the system status of the AP.Table 1 AP-277 LED Meanings during Boot UpLED Color/State MeaningSystem LED Off No power to APRed Initial power-up Green - Flashing AP bootingGreen - Steady AP ready and 1000Mbps Ethernet link established. The LED turns off after 1200 secondsGreen - Yellow, 6 seconds period AP ready and 10/100Mbps Ethernet link established. The LED turns off after 1200 secondsAC Power InterfaceLAN PortWAN PortGrounding PointUSB Console Port, Reset button and LED
4AP-277 Outdoor Access Point | Installation GuideTable 2 AP-277 LED Meanings during OperationUSB Console PortThe USB Micro-B console port allows you to connect the AP to a terminal or a laptop for direct local management. Use the included USB console cable to connect the AP. You can download the necessary driver for USB-UART adapter from support.arubanetworks.com under the Tools & Resources tab.Use the following setting to access the terminal:Ethernet PortsAP-277 is equipped with two10/100/1000Base-T (RJ-45) Gigabit Ethernet ports (WAN and LAN port) for wired network connectivity. The WAN port supports 802.3at Power over Ethernet (PoE), accepting 48 VDC (nominal) as a standard defined Powered Device (PD) from a Power Sourcing Equipment (PSE) such as a PoE midspan injector.These ports have RJ-45 female connectors with the pin-outs shown in Figure 3. Figure 3 Gigabit Ethernet Port Pin-OutReset ButtonThe reset button can be used to return the AP to factory default settings. To reset the AP:1. Power off the AP.2. Press and hold the reset button using a small, narrow object, such as a paperclip.3. Power-on the AP without releasing the reset button. The system LED will flash within 5 seconds.4. Release the reset button.The system LED will flash again within 15 seconds indicating that the reset is completed. The AP will now continue to boot with the factory default settings.LED Color/State MeaningSystem LED Solid Red General faultOne blink off every 3 seconds Radio 0 fault (5 GHz)Two quick blink off 0.5 seconds apart cycled every 3 secondsRadio 1 fault (2.4GHz)Table 3 Console SettingsBaud Rate Data Bits Parity Stop Bits Flow Control9600 8 None 1 None1000Base-T Gigabit Ethernet PortRJ-45 FemalePin-OutSignal Name12345678BI_DC+BI_DC-BI_DD+BI_DD-BI_DA+BI_DA-BI_DB+BI_DB-FunctionBi-directional pair +C, POE PositiveBi-directional pair -C, POE PositiveBi-directional pair +D, POE NegativeBi-directional pair -D, POE NegativeBi-directional pair +A, POE NegativeBi-directional pair -A, POE NegativeBi-directional pair +B, POE PositiveBi-directional pair -B, POE Positive
AP-277 Outdoor Access Point | Installation Guide 5AC Power InterfaceThe AP-277 is capable of AC power in the range of 100 - 240 VAC. The power cord or power connector kit is sold separately.Grounding PointAlways remember to protect the AP by installing grounding lines. The ground connection must be complete before connecting power to the AP enclosure. Figure 4 AP-277 Top ViewFigure 5 AP-277 Bottom ViewBefore You BeginMounting Holder!CAUTIONFCC Statement: Improper termination of access points installed in the United States configured to non-US model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).
6AP-277 Outdoor Access Point | Installation GuidePre-Installation Network RequirementsAfter WLAN planning is complete and the appropriate products and their placement have been determined, the Aruba controller(s) must be installed and initial setup performed before the Aruba APs are deployed.For initial setup of the controller, refer to the ArubaOS Quick Start Guide for the software version installed on your controller.Pre-Installation ChecklistBefore installing your AP, be sure that you have the items listed below:Gigabit Ethernet cable of required lengthIEEE 802.3at compliant PoE source or AC power sourceAruba Mobility Controller configured and installed on the networkLayer 2/3 network connectivity to your APOne of the following network services:Aruba Discovery Protocol (ADP)DNS server with an “A” recordDHCP Server with vendor specific optionsVerifying Pre-Installation ConnectivityBefore you install APs in a network environment, make sure that the APs will be able to locate and connect to the controller when they are powered on.Specifically, you must verify the following conditions:When connected to the network, each AP is assigned a valid IP address.!CAUTIONEU Statement: Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide for details on restrictions.Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User Guide pour les details des restrictions.Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich Einschränkungen finden Sie im ArubaOS User Guide.Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS User Guide per avere informazioni detagliate sulle restrizioni.Aruba Networks, Inc. in compliance with governmental requirements, has designed the AP-277 such that only authorized network administrators can change configuration settings. For more information about AP configuration, refer to the ArubaOS Quick Start Guide and ArubaOS User Guide.!CAUTIONAccess points are radio transmission devices and as such are subject to governmental regulation. Network administrators responsible for the configuration and operation of access points must comply with local broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in which the access point will be used.
AP-277 Outdoor Access Point | Installation Guide 7APs can locate the controller.Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the controller.Outdoor Planning and Deployment ConsiderationsPrior to deploying an outdoor wireless network, the environment must be evaluated to plan for a successful Aruba WLAN deployment. Successfully evaluating the environment enables the proper selection of Aruba routers and antennas and assists in the determination of their placement for optimal RF coverage. This process is considered WLAN or RF planning and Aruba’s system engineers can assist in the outdoor planning process.For WLAN systems being installed outdoors in the USA, the following requirements must be met.1. Systems must be professionally installed by a qualified engineer familiar with WLAN, including Aruba trained partners and resellers.2. Operation in the 5600-5650-MHz band is prohibited.3. When within 35 km distance of a TDWR, the center frequency of the WLAN must be separated from the TDWR center frequency by 30 MHz.a. If the radar is operating from 5600-5610 MHz, disable the use of channel 116 (5580 MHz).b. If the radar is operating from 5630-5650 MHz, disable the use of channel 132 (5660 MHz).For TWDR locations in the US please refer to www.wispa.org/tdwr-locations-and-frequencies.Identifying Specific Installation LocationsYou can mount the AP-277 access point on a wall or pole. Use the AP placement map generated by Aruba’s RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/interference sources will impact RF propagation and should have been accounted for during the planning phase and adjusted for in RF plan.Identifying Known RF Absorbers/Reflectors/Interference SourcesIdentifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an AP to its fixed location. Examples of sources that degrade RF performance include:Cement and brickObjects that contain waterMetalMicrowave ovensWireless phones and headsetsInstalling the APService to all Aruba products should be performed by trained service personnel only.
8AP-277 Outdoor Access Point | Installation GuideUsing the AP-270-MNT-H1 Mounting KitThe AP-277 access point can be installed on a wall or attached to a pole by using AP-270-MNT-H1 mounting kit.Mounting the AP-277 Access Point to a Wall1. Use the mounting template provided in the AP-270-MNT-H1 mounting kit package to mark the four mounting points on the wall.2. Use a drill to create four holes on the four markings you created in the previous step.3. Insert an anchor bolt into each drilled hole. Anchor bolts are not included in the mounting kit package.4. Place the mounting bracket over the anchor bolts and press the bracket against the wall.5. Place the washers and nut onto the bolt’s threaded end and tighten the nut until the mounting bracket is firmly attached to the wall as shown in Figure 6.Figure 6 Attaching the Mounting Bracket to a wall6. Use the M10x30 screw (with washer) and M10 nut included in the package to attach the mounting holder to the mounting bracket as shown in Figure 7. The AP-277 access point does not ship with any mounting kit. The AP-270-MNT-H1 mounting kit is available as accessories and must be ordered separately.For details on AP-270-MNT-H1, please refer to the AP-270-MNT-H1 Installation Guide.
AP-277 Outdoor Access Point | Installation Guide 9Figure 7 Attaching the Mounting Holder to the Mounting Bracket7. Slide the holder of the AP into the opening of the mounting holder and use two M6x20 screws included in the package to fix the AP to the mounting holder as shown in Figure 8.Figure 8 Attaching the AP to the Mounting Holder
10 AP-277 Outdoor Access Point | Installation GuideFigure 9 Attaching the AP to the Mounting Holder (Completed)The inclination of the AP (mounted to the mounting holder) can be adjusted up to +/-45 degrees by inserting the M6x20 screw (included in the package) into the different holes on the mounting holder. 8. Use the cable tie to fasten the cables on the bracket.Mounting the AP to a Pole1. Begin by attaching the mounting bracket to the pole as shown in Figure 10.a. Pass a hose clamp through the two slots on the mounting bracket, attach the mounting bracket to the pole and tighten the clamp using a screw driver to twist its screw head.b. Use another hose clamp through the other two slots on the mounting bracket and tighten the clamp.Figure 10 Attaching the Mounting Bracket to a Pole2. Use the M10x30 screw (with washer) and M10 nut included in the package to attach the mounting holder to the mounting bracket as shown in Figure 11.
AP-277 Outdoor Access Point | Installation Guide 11Figure 11 Attaching the Mounting Holder to the Mounting Bracket3. Slide the holder of the AP into the opening of the mounting holder and use two M6x20 screws included in the package to fix the AP to the mounting holder as shown in Figure 12.Figure 12 Attaching the AP to the Mounting HolderFigure 13 Attaching the AP to the Mounting Holder (Completed)
12 AP-277 Outdoor Access Point | Installation GuideThe inclination of the AP (mounted to the mounting holder) can be adjusted up to +/-45 degrees by inserting the M6x20 screw (included in the package) into the different holes on the mounting holder. 4. Use the cable tie to fasten the cables on the bracket.Grounding the APThe grounding must be completed before powering up the AP. The grounding wire should be #8 AWG.1. Peel the cover of one end of the grounding wire and place the bare grounding wire into the included copper lug, and press firmly with the crimping pliers.2. Fasten the copper lug to the grounding hole on the AP with the included M4 x6 screw as shown in Figure 14. Figure 14 Grounding the AP Connecting the Ethernet CableTo connect the Ethernet cable to the AP, perform the following steps using the cable glands that ships with your AP.Figure 15 Installing a Cable Gland 1. Slide the sealing nut over the cable (without the RJ45 connector attached to the end).2. Slide the clamping ring over the cable.3. Using a crimping tool, attach the shielded RJ45 connector to the end of the cable.4. Remove the weatherproof cap on the Ethernet port. WARNINGFailure to use the included Ethernet cable glands can lead to connectivity and POE issues.The cable is not included and must be purchased separately. Purchase a suitable UV-resistant, outdoor rated, CAT 5E or better RJ45 cable for use with the AP.Sealing Nut Clamping Ring CAT 5E or Better CableSeals
AP-277 Outdoor Access Point | Installation Guide 135. Insert the RJ45 connector to the Ethernet port.6. Screw the clamping ring onto the Ethernet port.7. Screw the sealing nut onto the clamping ring.Connecting the Power CableThe AP-277 access point offers two ways to connect the unit to AC power. Two power cord variants are offered and a connector kit that allows the customer to assemble their own cable if the standard offering does not meet deployment needs.The applicable SKUs for these options are:The difference between the NA and INTL part variants is the color coding of the conductors. The North American cable uses Black (Hot), White (Neutral), and Green (Ground). The INTL part follows the international schema of Brown (Hot), Blue (Neutral) and Yellow/Green (Ground)Best Practice for Outdoor Connection to AC MainsIn all circumstances and with any outdoor infrastructure the recommended practice is to connect to AC mains in an order grade weather protected junction box. This needs to be implemented by a qualified resource in a manner that is consistent with the electrical code in force in the jurisdiction of deployment. In many countries this will require a licensed electrician to perform this operation.In Japan, this would is a Certified Electrician by Ministry of Economy, Trade and Industry.The use of plugs with infrastructure equipment is suitable only for temporary installs where nuisance tripping of GFI plugs is considered tolerable. Should it be desired to attach a plug to the cable assemblies then the installer is expected to follow all directions provided with the plug end in a fashion consistent with local electrical code.The seals inside the clamping ring by factory default is applicable for cables with 5-8.5 mm diameter. In the cable gland kit, another seals is provided for use with the cables with 7-10 mm diameter.!CAUTIONInstallation and service of Aruba products should be performed by Professional Installers in a manner that is consistent with the electrical code in force in the jurisdiction of deployment. In many countries this will require a licensed electrician to perform this operation. In Japan, this is a Certified Electrician by Ministry of Economy, Trade, and Industry.The AP-277 access point does not ship with any power cables. These are available as accessories and should be ordered separately.Table 4 SKUs for Powering OptionsPart Number DescriptionPC-OD-AC-P-NA Weatherproof AC power cable(5m), North America versionPC-OD-AC-P-INT Weatherproof AC power cable(5m), International (EU) versionCKIT-OD-AC-P Weatherproof connector kit for AC power interface
14 AP-277 Outdoor Access Point | Installation GuideUse of the CKIT-OD-AC-PAssembly instructions for this part are shipped with the part. All instructions must be followed to ensure proper assembly of the connector onto the cable.The required specifications for third party cable used with the CKIT solution are as follows:AC power cable specifications (when using AC connector kit and custom cable): minimum voltage/current rating 250V/1A, diameter 6-12mm, rated for outdoor use and UV exposureAC Power Cable Connector PIN OUT Figure 16 AC power cable connector Connecting the Power Cable to the AP1. Remove the weatherproof cap on the power interface. 2. Insert the power cable connector into the power interface and hand-fasten the locknut. Verifying Post-Installation ConnectivityThe integrated LEDs on the AP can be used to verify that the AP is receiving power and initializing successfully (see Table 1 and Table 2). Refer to the ArubaOS Quick Start Guide for further details on verifying post-installation network connectivity.Configuring the APAP Provisioning/ReprovisioningProvisioning parameters are unique to each AP. These local AP parameters are initially configured on the controller which are then pushed out to the AP and stored on the AP itself. Aruba recommends that provisioning settings be configured via the ArubaOS Web UI only. Refer to the ArubaOS User Guide for complete details.AP ConfigurationConfiguration parameters are network or controller specific and are configured and stored on the controller. Network configuration settings are pushed out to the AP(s) but remain stored on the controller.Configuration settings can be configured via the ArubaOS Web UI or ArubaOS CLI. Refer to the ArubaOS User Guide for complete details. HotNeutralGround
AP-277 Outdoor Access Point | Installation Guide 15Product SpecificationsMechanical:Device Dimensions (HxWxD): 10.6 inches x 9 inches x 9.4 inches (27cm x 23cm x 24cm)Weight: 4.4 lbs/2.0 kgElectricalEthernet2 x 10/100/1000Base-T auto-sensing Ethernet RJ-45 InterfacesMDI/MDXPower over Ethernet (IEEE 802.3at compliant), 48VDC/0.6APower100-240 VAC 50/60 Hz from external AC power sourcePOE support on WAN port: 802.3at-compliant POE sourcing devicesEnvironmentalOperatingTemperature: -40ºC to 60ºC (-40ºF to 140ºF)Humidity: 5% to 95% non-condensingStorageTemperature: -40ºC to 85ºC (-40ºF to 185ºF)For additional specifications on this product, please refer to the data sheet. The data sheet can be found at www.arubanetworks.com.
16 AP-277 Outdoor Access Point | Installation GuideSafety and Regulatory ComplianceAruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded from the following location: www.arubanetworks.com/safety_addendum Regulatory Model NameThe regulatory model name of AP-277 is APEX0102.FCCThis device is electronically labeled. To view the FCC ID:1. Log into the controller WebUI2. Navigate to Maintenance > Controller > About.FCC Class B Part 15This device complies with Part 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions:This device may not cause harmful interference.This device must accept any interference received, including interference that may causeundesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause interference harmful to radio communications.If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment to an outlet on a circuit different from that to which the receiver isconnected.Consult the dealer or an experienced radio or TV technician for help.!CAUTIONAruba access points must be installed by a professional installer. The professional installer is responsible for ensuring that grounding is available and it meets applicable local and national electrical codes.!CAUTIONRF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 13.78 inches (25 cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. !CAUTIONChanges or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
AP-277 Outdoor Access Point | Installation Guide 17EU Regulatory Conformance Aruba Networks, Inc., hereby declares that the APEX0101 and APEX0100 device models are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC -CE(!). The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at www.arubanetworks.com.Proper Disposal of Aruba EquipmentFor the most current information about Global Environmental Compliance and Aruba products, see our website at www.arubanetworks.com.Waste of Electrical and Electronic EquipmentAruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and Electronic Equipment (WEEE).European Union RoHSAruba products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this Directive.China RoHSAruba products also comply with China environmental declaration requirements and are labeled with the “EFUP 10” label shown at the left.10᳝↦᳝ᆇ⠽䋼ໄᯢHazardous Materials Declaration᳝↦᳝ᆇ⠽䋼៪ܗ㋴(Hazardous Substance) 䚼ӊৡ⿄(Parts) 䪙3E∲+J䬝&G݁Ӌ䫀&U໮⒈㘨㣃3%%໮⒈Ѡ㣃䝮3%'(⬉䏃ᵓ(PCA Boards) hƻƻ ƻ ƻ ƻᴎẄ㒘ӊ(Mechanical Sub-Assemblies)hƻƻ ƻ ƻ ƻƻ˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼ SJ/T11363-2006 ᷛޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽIndicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7ᷛޚ㾘ᅮⱘ䰤䞣㽕∖DŽIndicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼DŽThis table shows where these substances may be found in the supply chain of electronic information products, as of the date of sale of the enclosed product. ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ՟བ⬉∴ऩܗ῵ഫ䌈೼݊ѻકϞℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟ݠЁ᠔㾘ᅮⱘᴵӊϟᎹ԰The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here. The Environment- Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual.
18 AP-277 Outdoor Access Point | Installation GuideCanadian StatementUnder Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Canadian CautionThis radio transmitter (identify the device by certification number, or model number ifCategory II) has been approved by Industry Canada to operate with the antenna typeslisted below with the maximum permissible gain and required antenna impedance foreach antenna type indicated. Antenna types not included in this list, having a gaingreater than the maximum gain indicated for that type, are strictly prohibited for usewith this device.Gain of antenna: 7.4dBi for 2.4G band; 9.1dBi for 5G band;Type of antenna: directional;Impedance of antenna: 50ohmLe présent émetteur radio (identifier le dispositif par son numéro de certification ouson numéro de modèle s'il fait partie du matériel de catégorie I) a été approuvé parIndustrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous etayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne.Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gainmaximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.Gain d'antenne: 7.4dBi for 2.4G band; 9.1dBi for 5G band;Type d'antenne: 50 ohm, directionnel.(i)The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (II) High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
AP-277 Outdoor Access Point | Installation Guide 19This page is intentionally left blank.
© 2014 Aruba Networks, Inc. All rights reserved.www.arubanetworks.com1344 Crossman AvenueSunnyvale, California 94089Phone: 408.227.4500Fax 408.227.455020 AP-277 Outdoor Access Point | Installation GuideContacting Aruba NetworksWeb Site SupportMain Site http://www.arubanetworks.com Support Site https://support.arubanetworks.com Software Licensing Site https://licensing.arubanetworks.com/login.phpWireless Security IncidentResponse Team (WSIRT) http://www.arubanetworks.com/support/wsirt.phpSupport EmailsAmericas, APAC and EMEA support@arubanetworks.com WSIRT EmailPlease email details of any securityproblem found in an Aruba product.sirt@arubanetworks.comTelephone SupportAruba Corporate +1 (408) 227-4500FAX +1 (408) 227-4550SupportUnited States 800-WI-FI-LAN (800-943-4526)Universal Free Phone Service Number (UIFN): Australia, Canada, China, France, Germany, Hong Kong, Ireland, Israel, Japan, Korea, Singapore, South Africa, Taiwan, and the UK.+800-4WIFI-LAN (+800-49434-526)All Other Countries +1 (408) 754-1200

Navigation menu