Hewlett Packard Enterprise APIN0214215 Wireless Access Point User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	2315520
Application ID	pGS41ICtzND9kTY2leHL+Q==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	78.76kB (984476 bits)
Date Submitted	2014-07-03 00:00:00
Date Available	2014-07-16 00:00:00
Creation Date	2014-07-03 10:34:32
Producing Software	Adobe Acrobat 11.0.0
Document Lastmod	2014-07-03 13:58:44
Document Title	Manual
Document Creator	Adobe Acrobat 11.0.0

AP-210 Series Wireless Access Point
Installation Guide
The Aruba AP-214 and AP-215 wireless access points support the IEEE 802.11n
standard for high-performance WLAN. These access points use MIMO (Multiplein, Multiple-out) technology and other high-throughput mode techniques to
deliver high-performance, 802.11n 2.4 GHz and 802.11ac 5 GHz functionality
while simultaneously supporting existing 802.11a/b/g wireless services. The AP210 Series access points work only in conjunction with an Aruba Controller.
Figure 2 AP-210 Series Side View (AP-214 shown)
ANT2
ANT0
Ethernet Port
The 10/100/1000 Mbps Ethernet ports are on the bottom of the AP. These ports
have RJ-45 female connectors with the pin-outs shown in Figure 6.
Figure 6 Gigabit Ethernet Port Pin-Out
1000Base-T Gigabit
Ethernet Port
USB Port
RJ-45 Female
Pin-Out
External Antenna Connectors
The AP-214 is equipped with three external antenna connectors. The connectors
are labeled ANT0, ANT1, and ANT2, and correspond to radio chains 0, 1, and 2.

AP-214 or AP-215 Access Point
For optimal performance when using articulating direct-mount antennas,
professional installers must orient the antennas with ANT0 and ANT2 at 45
degree angles and ANT1 oriented straight out (see Figure 3).

9/16" and 15/16” Ceiling Rail Adapters
Figure 3 AP-214 Antenna Orientation

Installation Guide (this document)
Package Contents
Aruba Controller provisioned on the network:
 Layer 2/3 network connectivity to your access point
 One of the following network services:
AP-210 Series is equipped with one 10/100/1000Base-T (RJ-45) auto-sensing,
MDI/MDX wired-network connectivity port. This port supports IEEE 802.3af and
802.3at Power over Ethernet (PoE) compliance, accepting 48 VDC (nominal) as a
standard defined Powered Device (PD) from a Power Sourcing Equipment (PSE)
such as a PoE midspan injector, or network infrastructure that supports PoE.
The Aruba AP-210 Series access point provides the following capabilities:
 Wireless transceiver
 Protocol-independent networking functionality
 IEEE 802.11a/b/g/n/ac operation as a wireless access point
 IEEE 802.11a/b/g/n/ac operation as a wireless air monitor
 Compatibility with IEEE 802.3at PoE+ and 802.3af PoE
 Central management configuration and upgrades through a controller
The AP-210 Series requires ArubaOS 6.4.2.0 or later.
ANT1

Signal Name
Function
BI_DA+
BI_DABI_DB+
BI_DC+
BI_DCBI_DBBI_DD+
BI_DD-
Bi-directional pair +A
Bi-directional pair -A
Bi-directional pair +B
Bi-directional pair +C
Bi-directional pair -C
Bi-directional pair -B
Bi-directional pair +D
Bi-directional pair -D

Aruba Discovery Protocol (ADP)

DNS server with an “A” record

DHCP Server with vendor-specific options
Summary of the Setup Process
Successful setup of an AP-210 Series access point consists of five tasks, which
must be performed in this order:
1. Verify pre-installation connectivity.
2. Identify the specific installation location for each AP.
3. Install each AP.
4. Verify post-installation connectivity.
5. Configure each AP.
Aruba Networks, Inc., in compliance with governmental requirements, has designed
the AP-210 Series access points so that only authorized network administrators can
change the settings. For more information about AP configuration, refer to the
ArubaOS Quick Start Guide and ArubaOS User Guide.
DC Power Socket
If PoE is not available, an optional Aruba AP AC-DC adapter kit (sold separately)
can be used to power the AP-210 Series.
Additionally, a locally-sourced AC-to-DC adapter (or any DC source) can be used
to power this device, as long as it complies with all applicable local regulatory
requirements and the DC interface meets the following specifications:
Inform your supplier if there are any incorrect, missing, or damaged parts. If
possible, retain the carton, including the original packing materials. Use these
materials to repack and return the unit to the supplier if needed.


Access points are radio transmission devices and as such are subject to
governmental regulation. Network administrators responsible for the configuration
and operation of access points must comply with local broadcast regulations.
Specifically, access points must use channel assignments appropriate to the
location in which the access point will be used.
12 VDC (+/- 5%)/18W
Center-positive 1.7/4.0 mm circular plug, 9.5 mm length
AP-210 Series Hardware Overview
Reset Button
Figure 1 AP-210 Series LEDs
The reset button can be used to return the AP to factory default settings. To reset
the AP:
Verifying Pre-Installation Connectivity
1. Power off the AP.
Before you install APs in a network environment, make sure that the APs are
able to locate and connect to the controller after power on.
USB Interface
PW R
ENET 5Ghz 2.4 Gh z
The AP-210 Series is equipped with a USB interface for connectivity with cellular
modems.
The USB interface is disabled when the AP-210 Series is powered from 802.3af PoE.
The AP-210 Series is equipped with four LEDs that indicate the status of the
various components of the AP.



3. Power-on the AP without releasing the reset button. The power LED will
flash within 5 seconds.
4. Release the reset button.
The power LED will flash again within 15 seconds indicating that the reset is
completed. The AP will now continue to boot with the factory default settings.
LEDs

2. Press and hold the reset button using a small, narrow object, such as a
paperclip.
Figure 4 AP-210 Series Rear
Before You Begin
PWR: Indicates whether or not the AP-210 Series is powered-on
ENET: Indicates the status of the AP-210 Series’ Ethernet port
5 GHz: Indicates the status of the 802.11a/n radio
2.4 GHz: Indicates the status of the 802.11b/g/n radio
Table 1 AP-210 Series Series LED Meanings
LED
Color/State
Meaning
PWR
Off
No power to AP
Red
Initial power-up
Green - Flashing
AP booting
Green - Steady
AP ready
Off
Ethernet link unavailable
Yellow - Steady
10/100Mbps Ethernet link established
Green - Steady
1000Mbps Ethernet link established
Flashing
Ethernet link activity
Off
5 GHz radio disabled
Yellow - Steady
5 GHz radio enabled in non-HT WLAN mode
Green - Steady
5 GHz radio enabled in HT WLAN mode
Flashing - Green
5 GHz Air or Spectrum Monitor
Console Port
Off
2.4 GHz radio disabled
The serial console port allows you to
connect the AP to a serial terminal or a
laptop for direct local management. This
port is an RJ-45 female connector with
the pinouts described in . Connect it
directly to a terminal or terminal server
using an Ethernet cable.
ENET
FCC Statement: Improper termination of access points installed in the United States
configured to non-US model controllers will be in violation of the FCC grant of
equipment authorization. Any such willful or intentional violation may result in a
requirement by the FCC for immediate termination of operation and may be subject
to forfeiture (47 CFR 1.80).
EU Statement:
Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer
to the ArubaOS User Guide for details on restrictions.
Produit rĂŠseau local radio basse puissance operant dans la bande frĂŠquence 2.4
GHz et 5 GHz. Merci de vous referrer au ArubaOS User Guide pour les details des
restrictions.
Specifically, you must verify the following conditions:
 When connected to the network, each AP is assigned a valid IP address
 APs are able to locate the controller
Refer to the ArubaOS Quick Start Guide for instructions on locating and
connecting to the controller.
Identifying Specific Installation Locations
You can mount the AP-210 Series access point on a wall or on the ceiling. Use the
AP placement map generated by Aruba’s Airwave VisualRF Plan software
application to determine the proper installation location(s). Each location
should be as close as possible to the center of the intended coverage area and
should be free from obstructions or obvious sources of interference. These RF
absorbers/reflectors/interference sources will impact RF propagation and
should have been accounted for during the planning phase and adjusted for in
VisualRF plan.
Identifying Known RF Absorbers/Reflectors/Interference
Sources
Identifying known RF absorbers, reflectors, and interference sources while in
the field during the installation phase is critical. Make sure that these sources are
taken into consideration when you attach an AP to its fixed location. Examples
of sources that degrade RF performance include:
Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere
Informationen bezlßglich Einschränkungen finden Sie im ArubaOS User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento
alla ArubaOS User Guide per avere informazioni detagliate sulle restrizioni.




5 GHz
2.4 GHz
Yellow - Steady
2.4 GHz radio enabled in non-HT WLAN
mode
Green - Steady
2.4 GHz radio enabled in HT WLAN mode
Flashing - Green
2.4 GHz Air or Spectrum Monitor
Cement and brick
Objects that contain water
Metal
Microwave ovens
Wireless phones and headsets
Pre-Installation Network Requirements
After WLAN planning is complete and the appropriate products and their
placement have been determined, the Aruba controller(s) must be installed and
initial setup performed before the Aruba APs are deployed.
Installing the AP
Service to all Aruba Networks products should be performed by trained service
personnel only.
For initial setup of the controller, refer to the ArubaOS Quick Start Guide for
the software version installed on your controller.
Figure 5 Serial Port Pin-Out
Serial
Console Port
RJ-45 Female
Pin-Out
Direction
Input
Output
AP Pre-Installation Checklist
Before installing your AP-210 Series AP, ensure that you have the following:
TxD
GND
GND
RxD


CAT5e or better UTP cable of required length
One of the following power sources:
 IEEE 802.3at or 802.3af-compliant Power over Ethernet (PoE) source. The
POE source can be any power source equipment (PSE) controller or
midspan PSE device
 Aruba AP AC-DC adapter kit (sold separately)
Using the Ceiling Rail Adapter
The AP-210 Series ships with two ceiling rail adapters for 9/16” and 15/16” ceiling
rails. Additional wall mount adapters and ceiling rail adapters for other rail
styles are available as accessory kits.
Make sure the AP fits securely on the ceiling tile rail when hanging the device
from the ceiling, because poor installation could cause it to fall onto people or
equipment.
1. Pull the necessary cables through a prepared hole in the ceiling tile near
where the AP will be placed.
Product Specifications
FCC Class B Part 15
2. Place the adapter against the back of the AP with the adapter at an angle of
approximately 30 degrees to the tabs (see Figure 7).
Electrical
This device complies with Part 15 of the Federal Communications Commission (FCC) Rules.
Operation is subject to the following two conditions:

3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure 7).
Figure 7 Attaching the Ceiling Rail Adapter

Ethernet:
 1x 10/100/1000 auto-sensing Ethernet RJ-45 Interface
 MDI/MDX
 IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)
 Power over Ethernet (IEEE 802.3at and 802.3af compliant), 48V DC (nominal) and 56V DC
(maximum)/350mA (see Figure 6 for pin configuration)
Power:
 12 VDC power interface, supports powering through an AC-to-DC power adapter
 POE support on Ethernet ports: 802.3at-compliant and 802.3af-compliant POE sourcing
devices
If a power adapter other than the one provided by Aruba Networks is used in the US
or Canada, it should be cULus (NRTL) Listed, with an output rated 12 VDC, minimum
1.5A, marked “LPS” or “Class 2,” and suitable for plugging into a standard power
receptacle in the US and Canada.
1.
This device may not cause harmful interference.
2.
This device must accept any interference received, including interference that may cause
undesired operation.
AP-110_04
Proper Disposal of Aruba Equipment
For the most current information about Global Environmental Compliance and Aruba products, see
our website at www.arubanetworks.com.
Waste of Electrical and Electronic Equipment
4. If necessary, connect the console cable to the console port on the back of the
AP.
Aruba products at end of life are subject to separate collection and treatment
in the EU Member States, Norway, and Switzerland and therefore are marked
with the symbol shown at the left (crossed-out wheelie bin). The treatment
applied at end of life of these products in these countries shall comply with
the applicable national laws of countries implementing Directive 2002/96EC
on Waste of Electrical and Electronic Equipment (WEEE).
5. Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots
at approximately a 30-degree angle to the ceiling tile rail (see Figure 8). Make
sure that any cable slack is above the ceiling tile.
6. Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks
into place on the ceiling tile rail.
European Union RoHS
Aruba products also comply with the EU Restriction of Hazardous
Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of
specific hazardous materials in the manufacture of electrical and
electronic equipment. Specifically, restricted materials under the RoHS
Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury,
Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in
RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging
will be marked with the “RoHS” label shown at the left indicating conformance to this Directive.
Figure 8 Mounting the AP
China RoHS
10
Aruba products also comply with China environmental declaration requirements
and are labeled with the “EFUP 10” label shown at the left.
᳝↦᳝ᆇ⠽䋼ໄᯢ
Hazardous Materials Declaration
䚼ӊৡ⿄
(Parts)
⬉䏃ᵓ
(PCA Boards)
ᴎẄ㒘ӊ
AP-110_005
(Mechanical Sub-Assemblies)
᳝↦᳝ᆇ⠽䋼៪‫ܗ‬㋴(Hazardous Substance)
䬝
݁Ӌ䫀
໮⒈㘨㣃
&G
&U
3%%
䪙
3E
∲
+J
Ćť
Ćť
Ćť
Ćť
Ćť
Ćť
Ćť
Ćť
Ćť
Ćť
໮⒈Ѡ㣃䝮
3%'(
AP-210 Series Wireless
Access Point
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause
interference harmful to radio communications.
Installation Guide
If this equipment does cause interference, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:


For additional specifications on this product, please refer to the data sheet. The data sheet can be
found at www.arubanetworks.com.
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.


Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio or TV technician for help.
Complies with the Class B limits for radio noise emissions as set out in the interference-causing
equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.
Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel
brouilleur du Canada.
Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz
and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt
WLAN devices.
Contacting Aruba Networks
Web Support
Main Site
http://www.arubanetworks.com
Support Site
https://support.arubanetworks.com
This product is CE marked according to the provisions of the R & TTE Directive
(1999/5/EC) - CE(!). Aruba Networks Inc., hereby declares that the APIN0114 /
APIN0115 device models are in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC -CE(!)
Airheads Social Forums and Knowledge Base
community.arubanetworks.com
North American Telephone
1-800-943-4526 (Toll Free)
1-408-754-1200
The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at the
following location: http://support.arubanetworks.com
International Telephones
arubanetworks.com/support-services/aruba-supportprogram/contact-support/
Software Licensing Site
licensing.arubanetworks.com/login.php
Wireless Security Incident
Response Team (WSIRT)
arubanetworks.com/support/wsirt.php
EU Regulatory Conformance
Canada
(i)les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont rĂŠservĂŠs uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mĂŞmes canaux;
(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 4705 725 MHz doit se conformer à la limite de p.i.r.e.;
(iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se
conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le
cas.
De plus, les utilisateurs devraient aussi ĂŞtre avisĂŠs que les utilisateurs de radars de haute puissance
sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et
5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs
LAN-EL.
Aucune émission n’est permise dans la bande 5 600-5 650 MHz. Jusqu’à nouvel avis,
les dispositifs visés par la présente annexe ne doivent pas être en mesure d’émettre
dans la bande 5 600-5 650 MHz, afin de protĂŠger les radars mĂŠtĂŠorologiques
d’Environnement Canada exploités dans cette bande.
ƻ˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼ SJ/T11363-2006 ᷛ‫ޚ‬㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ
Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is
below the relevant threshold of the SJ/T11363-2006 standard.
h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7ᷛ‫ޚ‬㾘ᅮⱘ䰤䞣㽕∖DŽ
Support Email Addresses
Americas and APAC
support@arubanetworks.com
EMEA
emea.support@arubanetworks.com
Americas and APAC Support Email
support@arubanetworks.com
WSIRT Email
Please email details of any security
problem found in an Aruba product.
wsirt@arubanetworks.com
Copyright
Š 2014 Aruba Networks, Inc. AirWaveŽ, Aruba NetworksŽ, Aruba Mobility Management SystemŽ, Bluescanner,
For Wireless That WorksÂŽ, Mobile Edge Architecture, People Move. Networks Must Follow., RFProtectÂŽ, The All
Wireless Workplace Is Now Open For Business, and The Mobile Edge CompanyÂŽ are trademarks of Aruba
Networks, Inc. All rights reserved. All other trademarks are the property of their respective owners.
Open Source Code
Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials
in the parts is above the relevant threshold of the SJ/T11363-2006 standard.
ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼DŽ
7. On the AP-214, install the external antennas according to the manufacturer’s
instructions, and connect the antennas to the antenna interfaces on the AP.
This table shows where these substances may be found in the supply chain of electronic information
products, as of the date of sale of the enclosed product.
ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ
՟བ⬉∴ऩ‫ܗ‬῵ഫ 䌈೼݊ѻકϞ
ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟‫ݠ‬Ё᠔㾘ᅮⱘᴵӊϟᎹ԰
The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are
per the symbol shown here. The Environment- Friendly Use Period is valid only when the
product is operated under the conditions defined in the product manual.
Connecting Required Cables
RF DĂŠclaration sur la radioexposition: Cet ĂŠquipement est conforme aux normes IC
Limites d'exposition aux rayonnements RF. Cet ĂŠquipement doit ĂŞtre installĂŠ et utilisĂŠ
Ă  une distance minimum de 7,9 pouces (20 cm) entre l'radiateur et votre corps pour
2,4 GHz et 5 GHz opĂŠrations. cet ĂŠmetteur ne doit pas ĂŞtre co-localisĂŠes ou opĂŠrant
en conjonction avec une autre antenne ou ĂŠmetteur.
Install cables in accordance with all applicable local and national regulations and
practices.
Verifying Post-Installation Connectivity
The integrated LEDs on the AP can be used to verify that the AP is receiving
power and initializing successfully (see Table 1). Refer to the ArubaOS Quick
Start Guide for further details on verifying post-installation network
connectivity.
Configuring the AP-210 Series
AP Provisioning/Reprovisioning
Provisioning parameters are unique to each AP. These local AP parameters are
initially configured on the controller which are then pushed out to the AP and
stored on the AP itself. Aruba recommends that provisioning settings be
configured via the ArubaOS Web UI only. Refer to the ArubaOS User Guide for
complete details.
AP Configuration
Configuration parameters are network or controller specific and are configured
and stored on the controller. Network configuration settings are pushed out to
the AP(s) but remain stored on the controller.
Configuration settings can be configured via the ArubaOS Web UI or ArubaOS
CLI. Refer to their respective guides for further details: the ArubaOS User Guide.
Certain Aruba products include Open Source software code developed by third parties, including software code
subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open
Source Licenses. The Open Source code used can be found at this site:
http://www.arubanetworks.com/open_source
Legal Notice
The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate
other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for
this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against
it with respect to infringement of copyright on behalf of those vendors.
India RoHS
Medical
This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling)
Rules, governed by the Ministry of Environment & Forests, Government of India.
1.
Equipment not suitable for use in the presence of flammable mixtures.
Warranty
2.
End product system, including power supply, must be evaluated to IEC 60601-1-1 and IEC 606011 by the end user.
This hardware product is protected by an Aruba warranty. For details, see Aruba Networks standard warranty
terms and conditions.
Safety and Regulatory Compliance
3.
Wipe with a dry cloth, no additional maintenance required.
4.
No serviceable parts, the unit must be sent back to the manufacturer for repair.
Aruba Networks provides a multi-language document that contains country-specific restrictions and
additional safety and regulatory information for all Aruba access points. This document can be
viewed or downloaded from the following location: www.arubanetworks.com/safety_addendum
5.
No modifications are allowed without Aruba approval.
Regulatory Model Names
The following regulatory model names apply to the AP-210 Series:


AP-214: APIN0214
AP-215: APIN0215
䫔⋩Ḵ㡅
ˢˢ䴻✳⺷娵嫱⎰㟤ᷳỶ≇䌯⮬柣暣㨇炻朆䴻姙⎗炻℔⎠ˣ⓮嘇ㆾἧ䓐侭⛯ᶵ⼿㑭冒嬲㚜柣䌯ˣ≈⣏
≇䌯ㆾ嬲㚜⍇姕妰ᷳ䈡⿏⍲≇傥ˤ
䫔⋩⚃㡅
ˢˢỶ≇䌯⮬柣暣㨇ᷳἧ䓐ᶵ⼿⼙枧梃凒⬱ℐ⍲⸚㒦⎰㱽忂ᾉ烊䴻䘤䎦㚱
⸚㒦䎦尉㗪炻ㅱ䩳⌛
䓐炻᷎㓡┬军䃉⸚㒦㗪㕡⼿两临ἧ䓐ˤ
ˢˢ⇵枭⎰㱽忂ᾉ炻㊯ὅ暣ᾉ㱽夷⭂ἄ㤕ᷳ䃉䶂暣忂ᾉˤ
FCC
ˢˢỶ≇䌯⮬柣暣㨇枰⽵⍿⎰㱽忂ᾉㆾⶍ㤕ˣ䥹⬠⍲慓䗪䓐暣㲊廣⮬⿏暣
This device is electronically labeled. To view the FCC ID:
ġġġġ㨇姕⁁ᷳ⸚㒦ˤ
1.
Log into the controller WebUI.
2.
Navigate to Maintenance > Controller > About.
RF Radiation Exposure Statement: This equipment complies with FCC RF
radiation exposure limits. This equipment should be installed and operated with a
minimum distance of 7.9 inches (20 cm) between the radiator and your body for 2.4
GHz and 5 GHz operations. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. When operated in the 5.15 to 5.25
GHz frequency range, this device is restricted to indoor use to reduce the potential
for harmful interference with co-channel Mobile Satellite Systems.
www.arubanetworks.com
1344 Crossman Avenue
Sunnyvale, California 94089
Phone: 408.227.4500
Fax 408.227.4550
AP-210 Series Wireless Access Point | Installation Guide
Part Number 0511513-02 | July 2014
To access the FCC ID from WebUI, 1. Log into the controller WebUI. 2. Navigate to Maintenance > Controller > About

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2014:07:03 10:34:32-07:00
Creator                         : Adobe Acrobat 11.0.0
Modify Date                     : 2014:07:03 13:58:44-07:00
Title                           : 
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2014:07:03 13:58:44-07:00
Creator Tool                    : Adobe Acrobat 11.0.0
Format                          : application/pdf
Document ID                     : uuid:37893e0f-aed3-4641-98c7-c00b06300a92
Instance ID                     : uuid:ad23532f-d0e4-4d0f-8cd3-d70d4dd64aea
Producer                        : Adobe Acrobat 11.0.0
Page Count                      : 3

EXIF Metadata provided by EXIF.tools