Hewlett Packard Enterprise APIN0314315 Aruba 310 Series Wireless Access Point User Manual

Aruba Networks, Inc. Aruba 310 Series Wireless Access Point

Contents

User Manual pt 2

Download: Hewlett Packard Enterprise APIN0314315 Aruba 310 Series Wireless Access Point User Manual
Mirror Download [FCC.gov]Hewlett Packard Enterprise APIN0314315 Aruba 310 Series Wireless Access Point User Manual
Document ID2992596
Application IDHbVgR7kmo7qegRbA9+WNNA==
Document DescriptionUser Manual pt 2
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize76.23kB (952854 bits)
Date Submitted2016-05-16 00:00:00
Date Available2016-11-12 00:00:00
Creation Date2007-05-15 12:46:36
Producing SoftwareAcrobat Distiller 11.0 (Windows)
Document Lastmod2016-01-19 11:01:49
Document Titleuntitled
Document CreatorFrameMaker 12.0

Aruba 310 Series Wireless Access Point
Regulatory Compliance and Safety Information Guide
Introduction
This document contains domestic and international regulatory compliance and safety information for 310 Series access points.
To ensure that this device complies with the regulatory standards for your region, please refer to the sections below.

Electrical and Environmental Specifications

Regulatory Information

Proper Disposal of Aruba Equipment
Electrical and Environmental Specifications
For additional specifications on this product, please refer to the product data sheet at www.arubanetworks.com/
safety_addendum.
All Aruba access points should be professionally installed by an Aruba Certified Mobility Professional (ACMP). The installer is
responsible for ensuring that grounding is available and meets applicable national and electrical codes.
Tous les points d'accès Aruba doivent impÊrativement être installÊs par un professionnel agrÊÊ. Ce dernier doit s'assurer
que l'appareil est mis Ă  la terre et que le circuit de mise Ă  la terre est conforme aux codes ĂŠlectriques nationaux en vigueur.
Electrical

Ethernet:




100/1000 Base-T auto-sensing Ethernet RJ45 interface
IEEE 802.3u (100 Base-T). IEEE 802.3ab (1000 Base-T)
Power over Ethernet IEEE 802.3at 56VDC (nominal) and 802.3af 48VDC (maximum).
Power:


48VDC power interference, support powering through an AC-to-DC power adapter (AP-AC-48V36B)
Maximum power consumption (excluding USB): 20W (PoE) or 18.5W (DC)
If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, without an
output rated 48VDC, minimum 2A, marked “LPS” and “Class 2”, and suitable for plugging into a standard power receptacle in
the US and Canada.
Environmental

Operating:



Temperature: 0°C to +50°C (+32°F to +122°F)
Humidity: 5% to 93% non-condensing
Storage and transport:

Temperature: -40°C to +70°C (40°F to +158°F)
Regulatory Information
The following regulatory model names apply to the 310 Series access points:

AP-314/IAP-314: APIN0314

AP-315/IAP-315: APIN0315
0511872-01 | January 2016
Aruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and
regulatory information for all Aruba access points. This document can be viewed or downloaded at www.arubanetworks.com.
FCC
RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should
be installed and operated with a minimum distance of 10.63 inches (27cm) between the radiator and your body for 2.4 GHz
and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. When operated in 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the
potential for harmful interference with co-channel Mobile Satellite Systems.
DĂŠclaration sur les limites d'exposition aux radiofrĂŠquences : cet ĂŠquipement est conforme aux limites d'exposition aux
rayonnements radioĂŠlectriques spĂŠcifiĂŠes par la FCC. Il doit ĂŞtre installĂŠ et utilisĂŠ Ă  une distance minimale de 27 cm par
rapport Ă  votre corps pour les frĂŠquences de 2,4 et 5 GHz. Cet ĂŠmetteur-rĂŠcepteur ne doit pas ĂŞtre utilisĂŠ ou situĂŠ Ă 
proximitĂŠ d'autres antennes ou ĂŠmetteurs-rĂŠcepteurs. En cas d'utilisation dans la plage de frĂŠquences de 5,15 Ă  5,25 GHz,
cet appareil doit uniquement être utilisÊ en intÊrieur afin de rÊduire les risques d'interfÊrence avec les systèmes satellites
mobiles partageant le mĂŞme canal.
FCC Class B Part 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the manufacturer’s instructions, may cause interference harmful to radio communications.
Operation is subject to the following conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired operation.
If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio or TV technician for help.
Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard
entitled “Digital Apparatus,” ICES-003 of Industry Canada.
Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850
MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s
authority to operate this equipment.
Toute modification effectuĂŠe sur cet ĂŠquipement sans l'autorisation expresse de la partie responsable de la conformitĂŠ est
susceptible d'annuler son droit d'utilisation.
Canada
Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled
“Digital Apparatus,” ICES-003 of Industry Canada.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (E.I.R.P.) does not exceed the
limit necessary for successful communication.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
Déclaration d’Industrie Canada
Cet appareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada.
Conformément aux réglementations d’Industrie Canada, cet émetteur-récepteur radio doit être utilisé uniquement avec une
antenne dont le type et le gain maximal doivent ĂŞtre approuvĂŠs par Industrie Canada. Pour rĂŠduire les interfĂŠrences radio
Aruba 310 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide
potentielles, le type d’antenne et son gain doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente
(PIRE) ne dĂŠpasse pas les valeurs nĂŠcessaires Ă  une communication efficace.
Ce périphérique est conforme aux règlements RSS exempts de licence d’Industrie Canada. L’utilisation de ce périphérique est
soumise aux deux conditions suivantes : (1) ce périphérique ne doit pas provoquer d’interférences, et (2) ce périphérique doit
accepter toute interfĂŠrence, y compris les interfĂŠrences susceptibles de provoquer un dysfonctionnement.
EU Regulatory Conformance
below:
Aruba Networks Inc., hereby declares that Aruba 310 Series access points are in compliance with directives listed

EMC Directive 2004

Low Voltage Directive 2006

R&TTE Directive 1999

REACH Regulation (EC) No.: 1907/2006

RoHS Directive 2011

WEEE Directive 2002
A Declaration of Conformity for these directives is available for viewing at www.arubanetworks.com.
Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850
MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices.
Medical
1. Equipment not suitable for use in the presence of flammable mixtures.
2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is responsible
for the resulting medical system complies with the requirements of IEC 60601-1 3rd edition.
3. Wipe with a dry cloth, no additional maintenance required.
4. No serviceable parts, the unit must be sent back to the manufacturer for repair.
5. No modifications are allowed without Aruba approval.
䬓⌨ṳ㢄 → 䴻✳⺷娵嫱⎰㟤ᷳỶ≇䌯⮬柣暣㨇炻朆䴻姙⎗炻℔⎠ˣ⓮嘇ㆾἧ䓐侭⛯ᶵ⼿㑭冒嬲㚜柣䌯ˣ≈⣏≇䌯ㆾ嬲㚜⍇姕妰ᷳ䈡⿏⍲≇傥ˤ
䬓⌨⛂㢄 → Ỷ≇䌯⮬柣暣㨇ᷳἧ䓐ᶵ⼿⼙枧梃凒⬱ℐ⍲⸚㒦⎰㱽忂ᾉ烊䴻䘤䎦㚱⸚㒦䎦尉㗪炻ㅱ䩳⌛ 䓐炻᷎㓡┬军䃉⸚㒦㗪㕡⼿两临ἧ䓐ˤ
⇵枭⎰㱽忂ᾉ炻㊯ὅ暣ᾉ㱽夷⭂ἄ㤕ᷳ䃉䶂暣忂ᾉˤỶ≇䌯⮬柣暣㨇枰⽵⍿⎰㱽忂ᾉㆾⶍ㤕ˣ䥹⬠⍲慓䗪䓐暣㲊廣⮬⿏暣㨇姕⁁ᷳ⸚㒦ˤ
Expected Service Life 10 years. For additional compliance information, refer to the label on the side of this device.
Proper Disposal of Aruba Equipment
Dispose of Aruba products per local regulation. For the most current information about Global Environmental Compliance and
Aruba products, see our website at www.arubanetworks.com.
Waste of Electrical and Electronic Equipment
Aruba products at end of life are subject to separate collection and treatment in the EU Member States,
Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie
bin). The treatment applied at end of life of these products in these countries shall comply with the
applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and
Electronic Equipment (WEEE).
India RoHS
This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) Rules, governed by the
Ministry of Environment & Forests, Government of India.
European Union RoHS
Aruba products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC
(RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and
electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including
Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine.
Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit
assemblies). Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this
directive.
Aruba 310 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide
China RoHS
10
Aruba products also comply with China environmental declaration requirements and are labeled with the
“EFUP 10” label shown at the left.
᳝↦᳝ᆇ⠽䋼ໄᯢ
Hazardous Materials Declaration
䚼ӊৡ⿄
(Parts)
⬉䏃ᵓ
(PCA Boards)
ᴎẄ㒘ӊ
(Mechanical Sub-Assemblies)
ƻ˖
᳝↦᳝ᆇ⠽䋼៪‫ܗ‬㋴(Hazardous Substance)
䬝
݁Ӌ䫀
໮⒈㘨㣃
&G
&U
3%%
䪙
3E
∲
+J
Ćť
Ćť
Ćť
Ćť
Ćť
Ćť
Ćť
Ćť
Ćť
Ćť
໮⒈Ѡ㣃䝮
3%'(
㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼ SJ/T11363-2006 ᷛ‫ޚ‬㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ
Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is
below the relevant threshold of the SJ/T11363-2006 standard.
h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7ᷛ‫ޚ‬㾘ᅮⱘ䰤䞣㽕∖DŽ
Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials
in the parts is above the relevant threshold of the SJ/T11363-2006 standard.
ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼DŽ
This table shows where these substances may be found in the supply chain of electronic information
products, as of the date of sale of the enclosed product.
ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ
՟བ⬉∴ऩ‫ܗ‬῵ഫ 䌈೼݊ѻકϞ
ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟‫ݠ‬Ё᠔㾘ᅮⱘᴵӊϟᎹ԰
The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are
per the symbol shown here. The Environment- Friendly Use Period is valid only when the
product is operated under the conditions defined in the product manual.
Š Copyright 2016 Hewlett Packard Enterprise Development LP
a Hewlett Packard
Enterprise company
www.arubanetworks.com
1344 Crossman Avenue
Sunnyvale, California 94089
Phone: 408.227.4500
Fax: 408.227.4550
Aruba 310 Series Wireless Access Point
| Regulatory Compliance and Safety Information Guide

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Language                        : en
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.150055, 2012/11/19-18:45:32
Creator Tool                    : FrameMaker 12.0
Modify Date                     : 2016:01:19 11:01:49-08:00
Create Date                     : 2007:05:15 12:46:36Z
Metadata Date                   : 2016:01:19 11:01:49-08:00
Format                          : application/pdf
Title                           : untitled
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:1e63e717-1db8-4673-b7e1-2225d3b15878
Instance ID                     : uuid:d430f126-d4a2-49d5-8325-12147e534ba3
Page Mode                       : UseOutlines
Page Count                      : 4
Creator                         : FrameMaker 12.0
EXIF Metadata provided by EXIF.tools
FCC ID Filing: Q9DAPIN0314315

Navigation menu