Hewlett Packard Enterprise APIN0314315 Aruba 310 Series Wireless Access Point User Manual 0511871 01 AP 31x IG

Download:
Mirror Download [FCC.gov]
Document ID	2992575
Application ID	vQClkQ88qhMWzqPz00ai1Q==
Document Description	User Manual pt 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	140.95kB (1761817 bits)
Date Submitted	2016-05-16 00:00:00
Date Available	2016-11-12 00:00:00
Creation Date	2015-05-01 04:46:49
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2016-01-21 16:09:31
Document Title	0511871-01_AP-31x_IG.fm
Document Creator	FrameMaker 12.0
Document Author:	mmclaughlin

Aruba 310 Series Wireless Access Point
Installation Guide
The Aruba 310 Series Wireless Access Points support IEEE 802.11ac
standards for a high-performance WLAN. This device is equipped with two
single-band radios, which provide network access and monitor the network
simultaneously. This access point to deliver high-performance 802.11n
2.4GHz and 802.11ac 5GHz functionality, while also supporting 802.11a/b/g
wireless services. Multi-user Multiple-in, Multiple-output (MU-MIMO) is
enabled when operating in 5GHz mode for optimal performance.
LED
Color/State
Meaning
The reset button can be used to return the access point to factory default
settings. To reset the access point, refer to the steps below:
System Status
(Left)
Off
Device powered off
1. Power off the access point.
Green- blinking
Device booting, not ready for use
Green- solid
Device ready for use
Amber- solid
Device ready; Power Save mode (802.3af
PoE)
When powered by an 802.3at or DC source, the USB port can supply power
up to 5W.
Amber- blinking
Device operating in restricted mode. Meets
one of the following conditions:
 Uplink negotiated in sub-optimal speed
(<1Gbps), or
 Ethernet radio is in non High-Throughput
(HT) mode
The USB interface is disabled when the access point is powered by an
802.3af PoE source.
The AP-314 and AP-315 access points work in conjunction with an Aruba
controller, while IAP-314 and IAP-315 access points can be configured via
built-in virtual controller.
310 Series wireless access points provides the following capabilities:







IEEE 802.11a/b/g/n/ac wireless access point
IEEE 802.11a/b/g/n/ac wireless air monitor
IEEE 802.11a/b/g/n/ac spectrum monitor
Compatible with IEEE 802.3at and 802.3af PoE
Support for MCS8 and MCS9
Centralized management, configuration and upgrades
Integrated Bluetooth Low Energy (BLE) radio
Package Contents






(I)AP-314 or (I)AP-315 access point
9/16" and 15/16” Ceiling Rail Adapters
Safety, Compliance, and Warranty Information guide
Aruba Instant Quick Start Guide (IAP-314 and IAP-315 only)
Aruba Professional Installation Guide (IAP-314 only)
Aruba 310 Series Wireless Access Point Installation Guide (this document)
Inform your supplier if there are any incorrect, missing, or damaged
parts. If possible, retain the carton, including the original packing
materials. Use these materials to repack and return the unit to the
supplier if needed.
Software
AP-314 and AP-315 access points require ArubaOS 6.5.0 or higher. For
additional information, refer to the ArubaOS User Guide and ArubaOS Quick
Start Guide.
Aruba access points are classified as radio transmission devices, and are
subject to government regulations of the host country. The network
administrator(s) is/are responsible for ensuring that configuration and
operation of this equipment meet all regulatory standards of their
country/domain.
For complete list of country-approved channels and devices, refer to the
Aruba Downloadable Regulatory Table at www.arubanetworks.com.
Reset Button
Figure 3 USB Port
Table 1: 310 Series LED Status Indicators
Radio Status
(Right)
2. Press and hold the reset button using a small, narrow object, such as a
paperclip.
Green/Ambersolid
No software setting/network restrictions
Red
System error condition
Off
Device powered off; or both radios disabled
Green- solid
Both radios enabled in access mode
Green- blinking
One radio enabled in access mode; other
disabled
Amber- solid
Both radios enabled in monitor mode
Amber- blinking
One radio enabled in monitor mode; one
radio disabled
Alternating

Figure 4 Back Panel
The power LED will flash again within 15 seconds indicating that the reset is
completed. The access point will now continue to boot with the factory
default settings.
The Ethernet port supports PoE-in and may draw power from an 802.3at
(recommended) or an 802.3af source.
Ethernet Port
If PoE is unavailable, the 310 Series access points have a single 12V/36W DC
power input to support the AP-AC-V30B AC-to-DC power adapter kit (sold
separately).
When both 802.3at and DC power sources are available, the DC power
source will take precedence. The Access point will simultaneously draw a
minimal current from the PoE source. In the event that the DC source fails,
the access point will switch to the 802.3at source.
Kensington
Lock
The 310 Series operates without restriction when powered by 802.3at
compliant and DC power sources. In this mode the USB interface is enabled
and supports up to 1A/5W to a powered device (PD).
DC Power
Socket
Green: one radio in access mode
Amber: one radio in monitor mode
When powered by an 802.3af PoE source, the access point operates in
power-saving mode. In this mode the USB interface is disabled.
Table 2: Power Modes
External Antenna Connectors
Reset Button
The (I)AP-314 access points are equipped with four external antenna
connectors located on the front corners of the access point (see Figure 2).
Figure 2 External Antenna Connectors
Console Port
ANT1
4. Release the reset button.
Power
USB Port
Console Port

3. Power-on the access point without releasing the reset button. The power
LED will flash within 5 seconds.
ANT0
The console port allows the user to connect the access point directly to a
serial terminal or laptop for local management. Connect the device to a
terminal or terminal server using an Ethernet cable.
Power Source
Limitations
USB Output
DC (AP-AC-12V30B)
No restrictions
1A/5W
PoE 802.3at
No restrictions
1A/5W
PoE 802.3af
USB disabled
Disabled
Before You Begin
The port is a 4-pin HDR connector with pin-out details in Figure 5.
FCC Statement: Improper termination of access points installed in the
United States configured to non-US model controllers is a violation of
the FCC grant of equipment authorization. Any such willful or intentional
violation may result in a requirement by the FCC for immediate
termination of operation and may be subject to forfeiture (47 CFR 1.80).
Figure 5 Serial Port Pin-Out
Pin
310 Series Hardware Overview
Figure 1 LED Status Indicators
ANT2
Signal
3.3V
RX
TX
GND
EU Statement:
Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands.
Please refer to the ArubaOS User Guide/Aruba Instant User Guide for
details on restrictions.
ANT3
Ethernet Ports
Antennas ports ANT0 and ANT1 have dual band functionality and support
both 2.4GHz and 5GHz, while ANT2 and ANT3 are single-band and support
5GHz only.
LEDs
The 310 Series has two LEDs that indicate the system and radio status.
The LEDs have three operating modes that can be selected in the system
management software:



Default mode: see Table 1
Off mode: LEDs are off
Blink mode: LEDs blink green
External antennas for this device must be installed by an Aruba Certified
Mobility Professional (ACMP) or other Aruba-certified technician, using
manufacturer-approved antennas only.
The Equivalent Isotropically Radiated Power (EIRP) levels for all external
antenna devices must not exceed the regulatory limit set by the host
country/domain.
Installers are required to record the antenna gain for this device in the
system management software.
Produit réseau local radio basse puissance operant dans la bande
fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User
Guide/Aruba Instant User Guide pour les details des restrictions.
The 310 Series is equipped with a 100/1000Base-T auto-sensing MDI/MDX
Ethernet port. This port supports wired-network connectivity, in addition to
Power over Ethernet (PoE) from IEEE 802.3af and 802.3at compliant power
sources.
Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band
arbeitet. Weitere Informationen bezlüglich Einschränkungen finden Sie
im ArubaOS User Guide/Aruba Instant User Guide.
This device accepts 56V DC (802.3at), or 48V DC (802.3af) nominal as a
standard powered device (PD) from power sourcing equipment, including
PoE midspan injector or a PoE-sourcing network infrastructure.
Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare
riferimento alla ArubaOS User Guide/Aruba Instant User Guide per avere
informazioni detagliate sulle restrizioni.
The port is an RJ45 connector, marked on the enclosure with
”57V
600mA.”
Figure 6 RJ45 Gigabit Port Pin-Out
1000Base-T Gigabit
Ethernet Port
RJ-45 Female
Pin-Out
USB Interface
The 310 Series is equipped with a USB port for connectivity with cellular
modems and other USB client devices.
Access Point Pre-Installation Checklist
Signal Name
Function
BI_DA+
BI_DABI_DB+
BI_DC+
BI_DCBI_DBBI_DD+
BI_DD-
Bi-directional pair +A
Bi-directional pair -A
Bi-directional pair +B
Bi-directional pair +C
Bi-directional pair -C
Bi-directional pair -B
Bi-directional pair +D
Bi-directional pair -D
Before installing your 310 Series access point, ensure that you have the
following:


CAT5E UTP cable or better
One of the following power sources:
 IEEE 802.3at or 802.3af-compliant Power over Ethernet (PoE) source.
The PoE source can be any power source equipment (PSE) controller
or midspan PSE device
 Aruba AP-AC-12V30UN adapter kit (sold separately)
Kensington Lock Slot
For AP-314 and AP-315 access points only:
The 310 Series is equipped with a Kensington lock slot for additional
security, shown in Figure 4.

Aruba controller provisioned on the network:
 Layer 2/3 network connectivity to your access point
 One of the following network services:

Aruba Discovery Protocol (ADP)

DNS server with an “A” record

DHCP Server with vendor-specific options.
Figure 7 Attaching the Ceiling Rail Adapter
Aruba Networks, Inc., in compliance with governmental requirements,
has designed the 310 Series access points so that only authorized
network administrators can change the settings. For more information
about access point configuration, refer to the ArubaOS Quick Start Guide/
Aruba Instant Quick Start Guide and ArubaOS User Guide/Aruba Instant
User Guide.
Aruba 310 Series Wireless
Access Point
Verifying Pre-Installation Connectivity
Installation Guide
The instructions for this section are applicable to the AP-314 and AP-315
only.
Before installing access points in a network environment, make sure that
they are able to locate and connect to the controller after power on.
Specifically, you must verify the following conditions:


When connected to the network, each access point is assigned a valid IP
address
Access points are able to locate the controller
Refer to the ArubaOS Quick Start Guide for instructions on locating and
connecting to the controller.
4. If necessary, connect the console cable to the console port on the back of
the access point.
5. Hold the access point next to the ceiling tile rail with the ceiling tile rail
mounting slots at approximately a 30-degree angle to the ceiling tile rail
(see Figure 8). Make sure that any cable slack is above the ceiling tile.
6. Pushing toward the ceiling tile, rotate the access point clockwise until the
device clicks into place on the ceiling tile rail.
Figure 8 Mounting the Access Point
a Hewlett Packard
Enterprise company
Contacting Aruba Networks
Web Support
Pre-Installation Network Requirements
Main Site
http://www.arubanetworks.com
After WLAN planning is complete and the appropriate products and their
placement have been determined, the Aruba controller(s) must be installed
and initial setup performed before the Aruba access points are deployed.
Support Site
https://support.arubanetworks.com
Airheads Social Forums and Knowledge Base
http://www.community.arubanetworks.com
North American Telephone
1-800-943-4526 (Toll Free)
1-408-754-1200
International Telephones
http://www.arubanetworks.com/support-services/
aruba-support-program/contact-support/
Software Licensing Site
http://licensing.arubanetworks.com
End-of-life Information
http://www.arubanetworks.com/support-services/endof-life/
Security Incident Response Team (SIRT)
http://www.arubanetworks.com/support-services/
security-bulletins/
For initial setup of the controller, refer to the ArubaOS Quick Start Guide for
the software version installed on your controller.
Identifying Specific Installation Locations
You can mount the 310 Series access point to a wall or on the ceiling. Use
the access point placement map generated by Aruba’s RF Plan software
application to determine the proper installation location(s). Each location
should be as close as possible to the center of the intended coverage area
and should be free from obstructions or obvious sources of interference.
These RF absorbers/reflectors/interference sources will impact RF
propagation and should have been accounted for during the planning phase
and adjusted for in RF plan.
Identifying Known RF Absorbers/Reflectors/Interference
Sources
Identifying known RF absorbers, reflectors, and interference sources while
in the field during the installation phase is critical. Make sure that these
sources are taken into consideration when you attach an access point to its
fixed location. Examples of sources that degrade RF performance include:





Cement and brick
Objects that contain water
Metal
Microwave ovens
Wireless phones and headsets
Installing the Access Point
Refer to the following steps to install your Aruba 310 Series access point
using the AP Ceiling Rail Mount Kit (AP-220-MNT-C1).
Using the Ceiling Rail Adapter
The 310 Series access point ships with two ceiling rail adapters for 9/16” and
15/16” ceiling rails. Additional wall mount adapters and ceiling rail adapters
for other rail styles are available as accessory kits.
This device must be professionally installed and serviced by an ACMP or
other Aruba-certified technician. The installer is responsible for securing
the access point onto the ceiling tile rail in accordance with the steps
below. Failure to properly install this product may result in physical
injury and/or damage to property.
1. Pull the necessary cables through a prepared hole in the ceiling tile near
where the access point will be placed.
2. Place the adapter against the back of the access point with the adapter at
an angle of approximately 30 degrees to the tabs (see Figure 7).
Support Email Addresses
7. On the (I)AP-314, install the external antennas according to the
manufacturer’s instructions, and connect the antennas to the antenna
interfaces on the access point.
Americas, EMEA and APAC
support@arubanetworks.com
Security Incident Response Team (SIRT) Email
sirt@arubanetworks.com
Connecting Required Cables
Copyright
Install cables in accordance with all applicable local and national regulations
and practices.
© Copyright 2016 Hewlett Packard Enterprise Development LP
Verifying Post-Installation Connectivity
Certain Aruba products include Open Source software code developed by third parties, including software
code subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other
Open Source Licenses. The Open Source code used can be found at this site:
http://www.arubanetworks.com/open_source
The integrated LEDs on the access point can be used to verify that the device
is receiving power and initializing successfully (see Table 1). Refer to the
ArubaOS Quick Start Guide for further details on verifying post-installation
network connectivity.
Open Source Code
Warranty
This hardware product is protected by an Aruba warranty. For details, see the Safety, Compliance, and
Warranty Information Guide included with this device.
Configuring the 310 Series
The instructions for the following section are applicable to AP-314 and AP315 model access points only.
Access Point Provisioning/Reprovisioning
Provisioning parameters are unique to each access point. These local access
point parameters are initially configured on the controller which are then
pushed out to the access points and stored on the devices. Aruba
recommends that provisioning settings be configured via the ArubaOS Web
UI only. Refer to the ArubaOS User Guide for complete details.
Access Point Configuration
Configuration parameters are network or controller specific and are
configured and stored on the controller. Network configuration settings are
pushed out to the access points, but remain stored on the controller.
Configuration settings can be configured via the ArubaOS Web UI or
ArubaOS CLI. Refer to their respective guides for further details: the ArubaOS
User Guide.
3. Twist the adapter clockwise until it snaps into place in the tabs (see
Figure 7).
a Hewlett Packard
Enterprise company
www.arubanetworks.com
1344 Crossman Avenue
Sunnyvale, California 94089
Phone: 408.227.4500
Fax 408.227.4550
Aruba 310 Series Wireless Access Point | Installation Guide
Part Number 0511871-02 | January 2016

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Language                        : en
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.150055, 2012/11/19-18:45:32
Producer                        : Acrobat Distiller 11.0 (Windows)
Creator Tool                    : FrameMaker 12.0
Modify Date                     : 2016:01:21 16:09:31-08:00
Create Date                     : 2015:05:01 04:46:49Z
Metadata Date                   : 2016:01:21 16:09:31-08:00
Format                          : application/pdf
Title                           : 0511871-01_AP-31x_IG.fm
Creator                         : mmclaughlin
Document ID                     : uuid:29a360a5-a285-45bb-ab4e-c498c6384979
Instance ID                     : uuid:bbc131f0-ae8a-4d59-b8d1-698f4365ed67
Page Mode                       : UseNone
Page Count                      : 2
Author                          : mmclaughlin

EXIF Metadata provided by EXIF.tools