Hewlett Packard Enterprise WL561 3COM WIRELESS 7760 11a/b/g POE ACCESS POINT User Manual KoalaQSG

Hewlett-Packard Company 3COM WIRELESS 7760 11a/b/g POE ACCESS POINT KoalaQSG

users manual 3

Download: Hewlett Packard Enterprise WL561 3COM WIRELESS 7760 11a/b/g POE ACCESS POINT User Manual KoalaQSG
Mirror Download [FCC.gov]Hewlett Packard Enterprise WL561 3COM WIRELESS 7760 11a/b/g POE ACCESS POINT User Manual KoalaQSG
Document ID643284
Application IDsrjyVpUKJOUm1d+zKy6Rnw==
Document Descriptionusers manual 3
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize45.67kB (570906 bits)
Date Submitted2006-04-03 00:00:00
Date Available2006-03-29 00:00:00
Creation Date2006-04-03 16:07:55
Producing SoftwareAcrobat Distiller 5.0.5 (Windows)
Document Lastmod2006-04-03 16:08:03
Document TitleKoalaQSG.fm
Document CreatorFrameMaker 7.0
Document Author: Owner

Checking the LED Indicators
When the access point is connected to power, LEDs indicate activity as follows (solid LED indicates
connection; blinking LED indicates activity):
LED
Color
Indicates
Power
Green
The access point is powered up
and operating normally.
The access point is not receiving
power or there is a fault with the
power supply.
PO
ER
11
11 a
b/
10
10
Off
11a
Green
Off
11b/g
Green
Off
100
Green
Off
10
Green
Off
The access point has WLAN
frame transmission over the
802.11a 5.3 GHz radio band.
No link is present.
The access point has WLAN
frame transmission over the
802.11g 2.4 GHz radio band.
No link is present.
The access point has a 100 Mbps
Fast Ethernet connection.
No link is present.
The access point has a 10 Mbps
Ethernet connection.
No link is present.
Troubleshooting
Refer to the Mobility System Configuration Guide or to the 3Com Wireless LAN Switch Reference
Manual to obtain the access point status.
Copyright Š 2004 3Com Corporation. All rights reserved. 3Com and the 3Com logo are registered
trademarks of 3Com Corporation. All other company and product names may be trademarks of the
respective companies with which they are associated.
DIA27507-5AAA01
Published October 2004
FEDERAL COMMUNICATIONS COMMISSION
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiated radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Note:
This device and its antenna(s) used for this transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the FCC
radio frequency exposure limits, human proximity to the antenna shall not be less than
20cm (8 inches) during normal operation.
According to 15.407(e):
If this device is going to be operated in 5.15 ~ 5.25GHz frequency range, then it is
restricted in indoor environment only.
RSS-GEN-7.1.4 Transmitter Antenna:
To reduce potential radio interference to other users, the antenna type and its gain of 8dBi.
should be so chosen that the equivalent isotropically radiated power (EIRP) is not more
than that required for successful communication.
This device has been designed to operate with an antenna having a maximum gain.
Antenna haveing a higher gain is strictly prohibited per regulations of industry
Canada. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than
that permitted for successful communication.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 3
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:1b2d7956-51c2-4c5c-9e7a-0a7f4ed55a41
Modify Date                     : 2006:04:03 16:08:03-04:00
Create Date                     : 2006:04:03 16:07:55-04:00
Metadata Date                   : 2006:04:03 16:08:03-04:00
Document ID                     : uuid:97bcb28d-129d-4232-96c8-fb450fa7a01f
Format                          : application/pdf
Title                           : KoalaQSG.fm
Creator                         : FrameMaker 7.0
Author                          : Owner
Producer                        : Acrobat Distiller 5.0.5 (Windows)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: O9C-WL561

Navigation menu