High Flying Electronics Technology HF-A21 HF-A21 User Manual GPON SFU System Design

High-Flying Electronics Technology Co., Ltd. HF-A21 GPON SFU System Design

User Manual

Download: High Flying Electronics Technology HF-A21 HF-A21 User Manual GPON SFU System Design
Mirror Download [FCC.gov]High Flying Electronics Technology HF-A21 HF-A21 User Manual GPON SFU System Design
Document ID3226043
Application IDICph0uNVFsPvRDS2Uvylaw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize121.36kB (1516972 bits)
Date Submitted2016-12-13 00:00:00
Date Available2016-12-13 00:00:00
Creation Date2016-11-01 15:28:32
Producing SoftwareMicrosoft® Word 2010
Document Lastmod2016-12-05 16:28:11
Document TitleGPON SFU System Design
Document CreatorMicrosoft® Word 2010
Document Author: Kevin Qiu

HF-A21 Embedded WiFi Module User Manual
HF-A21
Embedded WiFi Module User Manual
V1.0
Overview of Characteristic

Support IEEE802.11b/g/n Wireless Standards

Support TCP/UDP/HTTP Network Protocols

Support UART/Ethernet Data Interface

Support Work As STA/AP/AP+STA Mode

Support Router/Bridge Mode Networking

Support Internal/External Antenna Option

Support AT+ Instruction Set for Configuration

Support Friendly Web Configuration Page

Support Heatbeat Signal

Support Smart Link Application Tools

Support UART Free/Auto-Frame Function

Single +3.3V Power Supply

Small Size: 25 x 40mm

FCC/CE Certificated
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
HF-A21 Embedded WiFi Module User Manual
TABLE OF CONTENTS
1.
PRODUCT OVERVIEW ............................................................................................................... 6
1.1. General Specification ............................................................................................................. 6
1.2. Hardware Introduction ............................................................................................................ 7
1.2.1. Pins Definition .................................................................................................................... 7
1.2.2. Mechanical Size ................................................................................................................. 9
1.2.3. On-board Chip Antenna ..................................................................................................... 9
1.2.4. External Antenna ............................................................................................................. 10
1.2.5. Evaluation Kit ................................................................................................................... 10
1.2.6. Order Information ............................................................................................................. 12
1.3. Hardware Reference Design ................................................................................................ 12
1.3.1. Hardware Typical Application .......................................................................................... 12
1.4. Typical Application ............................................................................................................... 13
2.
PACKAGE INFORMATION ....................................................................................................... 14
5.1 Shipping Information ............................................................................................................ 14
APPENDIX A: EVB REFERENCE DESIGN ................................................................................... 15
APPENDIX B: CONTACT INFORMATION ..................................................................................... 16
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
HF-A21 Embedded WiFi Module User Manual
LIST OF FIGURES
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
HF-A21 Appearance .............................................................................................................. 7
HF-A21 Pins Map .................................................................................................................. 7
HF-A21 Mechanical Dimension ............................................................................................. 9
HF-A11 Chip Antenna Keep Out Region............................................................................... 9
Suggested Module Placement Region ................................................................................ 10
HF-A21 Evaluation Kit ......................................................................................................... 11
HF-A21 Order Information ................................................................................................... 12
HF-A11 Hardware Typical Application ................................................................................ 12
Shipping Information............................................................................................................ 14
LIST OF TABLES
Table 1
Table 2
Table 3
Table 4
HF-A21 Module Technical Specifications............................................................................... 6
HF-A21 Pins Definition ........................................................................................................... 7
HF-A11 External Antenna Parameters ................................................................................. 10
HF-A21 Evaluation Kit Interface Description ........................................................................ 11
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
HF-A21 Embedded WiFi Module User Manual
HISTORY
Ed. V1.0 Created on 5-09-2016.
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
HF-A21 Embedded WiFi Module User Manual
1. PRODUCT OVERVIEW
1.1. General Specification
Table 1
Class
Wireless
Parameters
HF-A21 Module Technical Specifications
Item
Parameters
Certification
FCC/CE
Wireless standard
Frequency range
802.11 b/g/n
2.412GHz-2.462GHz
802.11b: +20 dBm (Max.)
802.11g: +18 dBm (Max.)
802.11n: +15 dBm (Max.)
Transmit Power
Receiver Sensitivity
Antenna Option
Data Interface
Hardware
Parameters
Software
Parameters
Operating Voltage
Operating Current
Operating Temperature
Storage Temperature
Dimensions and Size
Network Type
Security Mechanisms
Encryption
Work Mode
Serial command
Network Protocol
Max. TCP Connection
User Configuration
User Application SW
802.11b: -89 dBm
802.11g: -81dBm
802.11n: -71dBm
External:I-PEX Connector
Internal:On-board PCB antenna
UART: 1200bps - 230400bps
Ethernet: 10Mbps/100Mpbs
GPIO,I2C
3.3V (+/-5%)
Avg:170mA Peak:400mA
-40℃- 85℃
-45℃- 125℃
25×40×8mm
STA /AP/AP+STA mode
WEP/WPA-PSK/WPA2-PSK/WAPI
WEP64/WEP128/TKIP/AES
Transparent Transmission
AT+instruction set
TCP/UDP/ARP/ICMP/DHCP/DNS/HTTP
32
Web Server+AT command config.
Support customized application SW
Provide SDK package
Provide smart link tools
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
HF-A21 Embedded WiFi Module User Manual
1.2. Hardware Introduction
Figure 1.
1.2.1.
Pins Definition
Figure 2.
Table 2
Pin
HF-A21 Appearance
HF-A21 Pins Map
HF-A21 Pins Definition
Description
Ground
VCC
UART Data Transmit
Name
GND
3.3V
UART_TXD
Direction
Power
Power
GPIO
UART Data Receive
GPIO12
UART_RXD
I/O
GPIO
GPIO
GPIO
GPIO13
GPIO4
GPIO5
I/O
I/O
I/O
Module reset signal
RESET
WiFi status Indication
GPIO
nLink
GPIO0
I/O
NOTE1
NOTE2
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
Note
3.3V @ 350mA power input
“Low ( 0 )” effective reset input.
The reset duration should be
kept more than 300ms
“1”- WIFI connection available,
“0”- No WIFI connection
Can be configured as GPIO.
HF-A21 Embedded WiFi Module User Manual
Indicate the module
status of power on
process
GPIO
Restore configuration
GPIO
nReady
GPIO35
nReload
GPIO34
I/O
I/O
11
Ethernet Interface
PHY_RX+
12
13
14
Ethernet Interface
Ethernet Interface
Ethernet Interface
PHY_RXPHY_TX+
PHY_TX-
10
“0” or “Palmodic Signal” - Finish
module boot up process;
“1” - Module boot up not finish.
Can be configured as GPIO.
Module will Restore factory
default configuration after set this
pin “0” more than 3s, then set
“1”.
Ethernet Data Interface, current
driver mode.
Note1: These Pins should not add external pull-up resistor. It's configure pin for module
bootup. There is pull-down resistor for UART_TXD. This pin must keep low when bootup.
Note2: UART_RXD has a 4.7K pulldown resistor.
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
HF-A21 Embedded WiFi Module User Manual
1.2.2. Mechanical Size
HF-A21 modules physical size as follows:
Figure 3.
HF-A21 Mechanical Dimension
1.2.3. On-board Chip Antenna
HF-A11 module support internal ob-board chip antenna option. When costomer select internal
antenna, you shall comply with following antenna design rules and module location suggestions:



For customer PCB, RED color region (6x8mm) can’t put componet or paste GND net;
Antenna must away from metal or high components at least 10mm;
Antenna can’t be shieldedby any meal enclosure; All cover, include plastic, shall away
from antenna at least 10mm;
Figure 4.
HF-A11 Chip Antenna Keep Out Region
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
HF-A21 Embedded WiFi Module User Manual
High-Flying suggest HF-A11 module better locate in following region at customer board, which to
reduce the effect to antenna and wireless signal, and better consult High-Flying technical people
when you structure your module placement and PCB layout.
Figure 5.
Suggested Module Placement Region
1.2.4. External Antenna
HF-A11 modules support internal antenna and external antenna option for user dedicated
application. If user select external antenna, HF-A11 modules must be connected to the 2.4G
antenna according to IEEE 802.11b/g/n standards.
The antenna parameters required as follows:
Table 3
HF-A11 External Antenna Parameters
Item
Parameters
Frequency range
2.4~2.5GHz
Impedance
VSWR
Return Loss
Connector Type
50 Ohm
2 (Max)
-10dB (Max)
I-PEX or populate directly
1.2.5. Evaluation Kit
High-Flying provides the evaluation kit to promote user to familiar the product and develop the
detailed application. The evaluation kit shown as below, user can connect to HF-A21 module with
the RS-232 UART port, 100M Eth port or Wireless port to configure the parameters, manage the
module or do the some functional tests.
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
HF-A21 Embedded WiFi Module User Manual
Figure 6.
HF-A21 Evaluation Kit
The external interface description for evaluation kit as follows:
Table 4
Function
External
Interface
LED
Button
HF-A21 Evaluation Kit Interface Description
Name
DC jack
Description
5~18V power input connector
3-Pin
3-Pin RS485 interface(Reserved)
DB9
Male serial jack of 9-pin,and used to connect to PC
RJ-45
Module
Power (Red)
TXD
RXD
Ready
Link
Reset
Reload
100M Eth Interface
2x7 2mm DIP connector
3.3V Power Indicator
TXD Indicator
RXD Indicator
nReady/GPIO Indicator
nLink/GPIO Indicator
Used to reset the module.
Module restore to factory default configuration.
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
10
HF-A21 Embedded WiFi Module User Manual
1.2.6. Order Information
Base on customer detailed requirement, HF-A21 series modules provide different variants and
physical type for detailed application.
Figure 7.
HF-A21 Order Information
1.3. Hardware Reference Design
1.3.1.
Hardware Typical Application
Figure 8.
HF-A11 Hardware Typical Application
Notes:
nRST- Module hardware reset signal. Input. Logics “0” effective.
There is 100K Ohm pull-up resister internal. When module power up or some issue happened,
MCU need assert nRST signal “0” at least 300ms, then set” 1” to keep module fully reset.
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
11
HF-A21 Embedded WiFi Module User Manual
nReady- Module boot up ready signal. Output. Logics “0” effective.
There is 4.7K Ohm pull-up resister internal. The module will output “0” “or “Palmodic Signal” after
normal boot up. This signal used to judge if module finish boot up and ready for application or
working at normal mode.
nLink- Module WIFI connection indication. Output.
There is 4.7K Ohm pull-up resister internal. When module connect to AP (STA mode) or some
WiFi STA connect to module (AP mode), the module will output “0”. This signal used to judge if
module already at WiFi connection status.
nReload- Module restore to factory default configuration.Input. Logics “0” effective.
User can assert nReload signal “0” more than 3’s through button or MCU pin, then release,
module will restore to factory default configuration and re-start boot up process. User need add
4.7K~10K Ohm pull-up resister external the module. If not use this function, then can use AT
command AT+FRLDEN=off to disable it.
UART_TXD/RXD- UART port data transmit and receive signal.
1.4. Typical Application
Refer to HF-A21-SMT user manual for detailed application and module usage.
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
12
HF-A21 Embedded WiFi Module User Manual
2. PACKAGE INFORMATION
5.1 Shipping Information
TRAY
Size: 370*270*40 mm
BOX
Size: 370*270*160 mm(inside)
Figure 9.
Shipping Information
Note:
1 tray = 100pcs
1 box = 4 trays = 4 * 100 pcs = 400pcs
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
13
HF-A21 Embedded WiFi Module User Manual
APPENDIX A: EVB REFERENCE DESIGN
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
14
HF-A21 Embedded WiFi Module User Manual
APPENDIX B: CONTACT INFORMATION
-----------------------------------------------------------------------------------------------------------Address: Room 1002,Building 1,No.3000,Longdong Avenue,Pudong New
Area,Shanghai,China, 201203
Web:
www.hi-flying.com
Service Online: 400-189-3108
Mail Contact: sales@hi-flying.com
-----------------------------------------------------------------------------------------------------------
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
15
HF-A21 Embedded WiFi Module User Manual
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed
and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
16
HF-A21 Embedded WiFi Module User Manual
FCC INFORMATION (additional)
OEM INTEGRATION INSTRUCTIONS:
This device is intended only for OEM integrators under the following conditions: The module must be
installed in the host equipment such that 20 cm is maintained between the antenna and users, and the
transmitter module may not be co-located with any other transmitter or antenna. The module shall
be only used with the internal antenna(s) that has been originally tested and certified with this
module. As long as 3 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed (for example, digital device emissions, PC
peripheral requirements, etc.).
Validity of using the module certification:
In the event that these conditions cannot be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC authorization for this module in combination
with the host equipment is no longer considered valid and the FCC ID of the module cannot be used
on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product (including the transmitter) and obtaining a separate FCC authorization.
End product labeling:
The final end product must be labeled in a visible area with the following: “Contains FCC ID:
2ACSVHF-A21”.
Information that must be placed in the end user manual:
The OEM integrator has to be aware
not to provide information to the end user regarding how to install or remove this RF module in
the user's manual of the end product which integrates this module. The end user manual shall
include all required regulatory information/warning as show in this manual.
Antenna Specification:
Type: Chip Antenna
Model: HF-A21
Brand: High-Flying
Gain: 2.0dBi
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
- 17 -
HF-A21 Embedded WiFi Module User Manual
END OF DOCUMENT
© Copyright High-Flying, May, 2011
The information disclosed herein is proprietary to High-Flying and is not to be used by or disclosed to unauthorized persons
without the written consent of High-Flying. The recipient of this document shall respect the security status of the information.
The master of this document is stored on an electronic database and is “write-protected” and may be altered only by
authorized persons at High-Flying. Viewing of the master document electronically on electronic database ensures access to
the current issue. Any other copies must be regarded as uncontrolled copies.
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com
- 18 -

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Has XFA                         : No
Language                        : zh-CN
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : Kevin Qiu
Description                     : SDC
Title                           : GPON SFU System Design
Create Date                     : 2016:11:01 15:28:32+08:00
Creator Tool                    : Microsoft® Word 2010
Modify Date                     : 2016:12:05 16:28:11+08:00
Metadata Date                   : 2016:12:05 16:28:11+08:00
Producer                        : Microsoft® Word 2010
Document ID                     : uuid:9769eef1-aa4f-44fa-ad31-b37665608df9
Instance ID                     : uuid:54b6ed1e-9b95-4b32-8092-c5761240d0d5
Page Count                      : 18
Author                          : Kevin Qiu
Subject                         : SDC
EXIF Metadata provided by EXIF.tools
FCC ID Filing: 2ACSVHF-A21

Navigation menu