Hilti BTAG TX-only beacon User Manual AI T380 ENU ROW

Hilti Corporation TX-only beacon AI T380 ENU ROW

07a. HILTI_2145807_User Manual

$***** For internal use only ***** 14.12.2017 / 13:06:37 - H2\DOK-Projekt\System\AI_T380\ENU\AI_T380_P1English 11 Information about the documentation1.1 About this documentation• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-freehandling and use of the product.• Observe the safety instructions and warnings in this documentation and on the product.• Always keep the operating instructions with the product and make sure that the operating instructionsare with the product when it is given to other persons.1.2 Explanation of symbols used1.2.1 WarningsWarnings alert persons to hazards that may occur when handling or using the product. The following signalwords are used in combination with a symbol:DANGER! Draws attention to an imminent hazard that will lead to serious personal injury orfatality.WARNING! Draws attention to a potential hazard that could lead to serious personal injury orfatality.CAUTION! Draws attention to a potentially dangerous situation that could lead to minor personalinjury or material damage.1.2.2 Symbols in the documentationThe following symbols are used in this document:Read the operating instructions before useInstructions for use and other useful information1.2.3 Symbols in the illustrationsThe following symbols are used in illustrations:These numbers refer to the corresponding illustrations found at the beginning of these operatinginstructions.The numbering reflects the sequence of operations shown in the illustrations and may deviatefrom the steps described in the text.Item reference numbers are used in the overview illustration and refer to the numbers used inthe key in the product overview section.This symbol is intended to draw special attention to certain points when handling the product.1.3 Product informationHilti products are designed for professional users and only trained, authorized personnel are permitted tooperate, service and maintain the products. This personnel must be informed of any particular hazards thatmay be encountered. The product and its ancillary equipment can present hazards if used incorrectly byuntrained personnel or if used not in accordance with the intended use.1.4 Declaration of conformityWe declare, on our sole responsibility, that the product described here complies with the applicable directivesand standards. A copy of the declaration of conformity can be found at the end of this documentation.The technical documentation is filed and stored here:Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany2 Safety2.1 General safety instructionsRead all safety instructions and other instructions.$

$***** For internal use only ***** 14.12.2017 / 13:06:37 - H2\DOK-Projekt\System\AI_T380\ENU\AI_T380_P12 EnglishKeep all safety instructions and other instructions for future reference.General safety instructions▶Do not cover a type identification plate or other labels.▶Do not cover any openings in the casing of the item of equipment.▶Do not obstruct switches, displays and warning lights.▶To avoid surface damage or chemical reactions, check that the adhesive is compatible with the surfacebefore applying the ON!Track smart tag.▶Keep away from children.3 Description3.1 Intended useThe Hilti AI T380 ON!Track smart tag makes it possible to clearly identify an item of equipment by way of aBluetooth signal, NFC signal or a 2D-barcode. After activation, the AI T380 continuously transmits a radiosignal that allows the user of the Hilti ON!Track system to determine the location of the item of equipment.A smartphone app and a Web application for the management of items of equipment is available from Hilti.The battery in the Hilti AI T380 ON!Track smart tag is not replaceable.3.2 Items supplied20 x AI T3801 x operating instructions3.3 AccessoriesAn additional adapter that allows the AI T380 to be attached to a cable or tied / clipped to an object isavailable from Hilti.3.4 Third-party wordmarks, trademarks and logosThe Bluetooth®wordmark and the logo are registered trademarks and the property of Bluetooth SIG, Inc.and Hilti has been granted a license to use these trademarks.The Android™ and Chrome™ trademarks are the property of Google Inc.The iPhone®and iOS trademarks are the property of Apple Inc.All other trademarks and wordmarks used, even when not expressly stated or marked as such, are theproperty of their applicable owners.4 Prerequisites4.1 PrerequisitesIn order to use the functionality of the AI T380, the Hilti ON!Track app is required. In order to use thiscorresponding app, a user name and a password are required.The minimum requirements are as follows:System requirementsSmartphone / tablet Android™ 5 (or higher)iOS®10 (or higher)Compatible with Bluetooth low energy devicesNear Field Communication (NFC) Necessary for activation and deactivationNot supported by the iPhone®Browser Internet Explorer or Chrome™For further information about Hilti ON!Track, please contact Hilti Service or visit http://ontrack.hilti.com.$

$***** For internal use only ***** 14.12.2017 / 13:06:37 - H2\DOK-Projekt\System\AI_T380\ENU\AI_T380_P1English 35 Technical data5.1 Technical dataProtection class IP 67Dimensions 38 mm x 28 mm x 11 mm (1.5''x 1.1'' x 0.4'')Operating temperature −20 ℃ …65 ℃(−4 ℉ …149 ℉)Storage temperature −25 ℃ …80 ℃(−13 ℉ …176 ℉)Battery (not replaceable) CR2032 button cellBattery life (at room temperature) 3 yearsCommunication standard Bluetooth® 4.0Signal range (can vary greatly depending on surrounding condi-tions)30 m(98 ft - 10 in)Signal interval 5 sFrequency 2,402 MHz …2,480 MHzMaximum emitted transmission power 3.20 mW6 Operation6.1 Activation1. Start the Hilti ON!Track app and select Activation from the menu.NoteThe ON!Track smart tag is switched off when supplied and must be activated before use.Activation is possible only using an Android device with NFC functionality.2. To begin activation, hold the ON!Track smart tag against the back of the smartphone, so that both are incontact.3. Move the ON!Track smart tag over the back of smartphone in order to find the position of the NFCantenna.NoteThe position of the NFC antenna on each smartphone model is different. Search for the right positionfor activation by moving the ON!Track smart tag around against the back of the smartphone.4. The smartphone provides confirmation as soon as the ON!Track smart tag has been activated.$

$***** For internal use only ***** 14.12.2017 / 13:06:37 - H2\DOK-Projekt\System\AI_T380\ENU\AI_T380_P14 English6.2 Deactivation1. Start the Hilti ON!Track app and select Deactivation from the menu.NoteDeactivation is possible only using an Android device with NFC functionality.2. To begin deactivation, hold the ON!Track smart tag against the back of the smartphone, so that both arein contact.3. Move the ON!Track smart tag over the back of smartphone in order to find the position of the NFCantenna.NoteThe position of the NFC antenna on each smartphone model is different. Search for the right positionfor deactivation by moving the ON!Track smart tag around against the back of the smartphone.4. The smartphone provides confirmation as soon as the ON!Track smart tag has been deactivated.7 TransportDeactivate the Hilti AI T380 ON!Track smart tag before transportation in an aircraft.NoteWhen traveling by air, please observe the regulations regarding restriction of the use of personalelectronic devices and Bluetooth devices, as issued by the applicable airline.8 RoHS (Restriction of Hazardous Substances)Click on the link to go to the table of hazardous substances: qr.hilti.com/r7068430.There is a link to the RoHS table, in the form of a QR code, at the end of this document.9 DisposalThe Hilti AI T380 ON!Track smart tag contains a battery.Do not dispose of the Hilti ON!Track smart tag AI T380 as household waste. Instead, dispose of it inaccordance with national regulations.10 Manufacturer’s warranty▶Please contact your local Hilti representative if you have questions about the warranty conditions.11 FCC statement (applicable in US) / IC statement (applicable in Canada)The product complies with part 15 of the FCC Rules and RSS210 of the IC.Operation is subject to the following two conditions:$

$***** For internal use only ***** 14.12.2017 / 13:06:37 - H2\DOK-Projekt\System\AI_T380\ENU\AI_T380_P1English 5•(1) This device shall cause no harmful interference.(2) This device must accept any interference received, including interference that may cause undesired operation.•Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deuxconditions suivantes :(1)l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter toutbrouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre lefonctionnement. NoteChanges or modifications not expressly approved by Hilti can restrict the user’s right to operate the device.Remarque:Hilti n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit lanature. Tout changement ou modification peuvent annuler le droit d’utilisation de l’appareil parl’utilisateur.FCC Class B Digital Device NoticeThis equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.• Consult the dealer or an experienced radio/TV technician for help.CAN ICES-3 (B) / NMB-3 (B)This Class B digital apparatus complies with Canadian$

$***** For internal use only ***** 14.12.2017 / 13:06:37 - H2\DOK-Projekt\System\AI_T380\ENU\AI_T380_P16 English$

$***** For internal use only ***** 14.12.2017 / 13:06:37 - H2\DOK-Projekt\System\AI_T380\ENU\AI_T380_P1EN 301 489-1 V2.2.0 (Draft) EN 301 489-3 V2.1.1 (Final Draft) EN 301 489-17 V3.2.0 (Draft) EN 300 328 V2.1.1 EN 62479:2010 EN 300 330 v.2.1.1 (2017-02)$

$***** For internal use only ***** 14.12.2017 / 13:06:37 - H2\DOK-Projekt\System\AI_T380\ENU\AI_T380_P1$

Hilti BTAG TX-only beacon User Manual AI T380 ENU ROW

Hilti Corporation TX-only beacon AI T380 ENU ROW

07a. HILTI_2145807_User Manual

Navigation menu

Namespaces

Views

Navigation