Hirschmann Automation and Control EWLAN2 802.11abgn Module User Manual U99EWLAN2 integration manual

Hirschmann Automation and Control GmbH 802.11abgn Module U99EWLAN2 integration manual

user manual

Download: Hirschmann Automation and Control EWLAN2 802.11abgn Module User Manual U99EWLAN2 integration manual
Mirror Download [FCC.gov]Hirschmann Automation and Control EWLAN2 802.11abgn Module User Manual U99EWLAN2 integration manual
Document ID2178954
Application IDCfVNRbAObgli5i4ILfsqSQ==
Document Descriptionuser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize43.42kB (542691 bits)
Date Submitted2014-01-28 00:00:00
Date Available2014-01-28 00:00:00
Creation Date2014-01-07 12:01:22
Producing SoftwareGPL Ghostscript 9.07
Document Lastmod2014-01-07 12:01:22
Document TitleU99EWLAN2_integration_manual
Document CreatorPDFCreator Version 1.7.1
Document Author: rxb12011

Integration Information
FCC ID: U99EWLAN2
IC: 4019A-EWLAN2
EWLAN2 integration manual
The EWLAN2 Module is a 3x3 3-stream IEEE 802.11 a/b/g/n wireless LAN
module in PCI express mini card form factor, designed to deliver high-reliable
radio performance for a variety of bandwidth-intensive wireless applications.
Outer Appearance
Top view with Samtec connector (PCI express):
Rear view with antenna connectors:
Dimensions:
34 mm (w) x 54mm (l) x 10 mm (h)
Page 1 of 9
Integration Information
FCC ID: U99EWLAN2
IC: 4019A-EWLAN2
General requirements:
This module is designed exclusively for usage in Hirschmann (Belden) host
equipment. A regulated power supply via the dedicated interface to the WLAN
module is required.
This RF module is approved only for use in products operating as fixed or mobile
transmitting device where the antennas are at least 50 cm away from any
persons during normal operating conditions.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
The integrator is still responsible for the FCC compliance requirement of the end
product, which integrates this module.
Appropriate measurements (e.g. 15 B compliance) and if applicable additional
equipment authorizations (e.g. Verification , Doc) of the host device to be
addressed by the integrator/manufacturer.
Hardware Integration
EWLAN2 supports the PCI express standard from the electrical power supply
and signaling point of view. To enhance connection reliability in harsh
environments between EWLAN2 and the host equipment, Samtec interface
connectors have been selected.
Page 2 of 9
Integration Information
FCC ID: U99EWLAN2
IC: 4019A-EWLAN2
EWLAN2 is equipped with Samtec connector QRM8
The host equipment has to be equipped with Samtec connector
QRF8-026-05.0-L-D-A-GP
Pin assignment of QRF8-026-05.0-L-D-A-GP
Page 3 of 9
Integration Information
FCC ID: U99EWLAN2
IC: 4019A-EWLAN2
Data Interface Pin definition
Pin
Signal
Comment
Pin
Signal
Comment
GND
ground
GND
ground
Res
open
Res
open
GND
ground
Res
open
Res
open
Res
open
GND
ground
10
Res
open
11
Res
open
12
GPIO10
GPIO-Interface
13
Res
open
14
GPIO7
GPIO-Interface
15
GND
ground
16
GND
ground
17
Res
open
18
PERST_L
/Reset
19
GND
ground
20
GND
ground
21
VCC3.3
3.3V ±5%
22
VCC3.3
3.3V ±5%
23
VCC3.3
3.3V ±5%
24
VCC3.3
3.3V ±5%
25
GND
ground
26
GND
ground
27
Res
open
28
PETp0
PCIe Tx+
29
GND
ground
30
PETn0
PCIe Tx-
31
Res
open
32
GND
ground
33
Res
open
34
PERp0
PCIe Rx+
35
GND
ground
36
PERn0
PCIe Rx-
37
GND
ground
38
GND
ground
Page 4 of 9
Integration Information
FCC ID: U99EWLAN2
IC: 4019A-EWLAN2
39
VCC1.2
1.2V ±5%
40
REFCLK+
PCIe Ref Clock+
41
VCC1.2
1.2V ±5%
42
REFCLK-
PCIe Ref Clock-
43
GND
ground
44
GND
ground
45
GND
ground
46
GND
ground
47
Res
open
48
CLKreq_L
/Clock request
49
Res
open
50
WAKE_L
/PCIe awake
51
GND
ground
52
GND
ground
Page 5 of 9
Integration Information
FCC ID: U99EWLAN2
IC: 4019A-EWLAN2
Power Requirements
EWLAN2 has to be powered as follows:
3.3VDC at VCC3.3
1.28VDC at VCC1.2
Antenna Connectors
The antenna connectors of EWLAN2 are micro miniature coaxial types (MMCX).
Antennas (USA/Canada)
The usage of the antennas for products shipped to North America (USA and
Canada) is restricted to the models and bands below:
Antennas operating with this device
model (Hirschmann model names)
(1)
BAT-ANT-RSMA-2AGN-R
BAT-ANT-N-3AGN-IP67
BAT-ANT-N-MiMoDB-5N-IP65
BAT-ANT-N-MiMo5-9N-IP65
BAT-ANT-N-8G-DS-IP65
(2)
BAT-ANT-N-MiMo-18N-IP65
2.4 GHz
Band
Yes
Yes
Yes
No
Yes
No
Permitted band of operation
5.15-5.25 GHz
5.725-5.825 GHz
Band
Band
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
Yes
Note (1): When using three antennas of the type BAT-ANT-RSMA-2AGN-R, each
antenna has to be aligned into a separate spatial direction (x-y-z), where one
antenna is perpendicular to the device and the other two are at right angles to
each other.
Note (2): Antenna BAT-ANT-N-MiMo-18N-IP65 has to be connected to the WLAN
main unit as below:
Antenna port “Ver” to WLAN antenna port 1
Antenna port “+45” to WLAN antenna port 2
Antenna port “-45” to WLAN antenna port 3
Other connection combinations are not permitted.
Page 6 of 9
Integration Information
FCC ID: U99EWLAN2
IC: 4019A-EWLAN2
SW Integration
EWLAN2 is designed for usage with Hirschmann host equipment (motherboards)
running the HiLCOS operating system 8.60.x or higher versions.
Only HiLCOS versions with fixed (non-adjustable) radio parameters for
USA/Canada are allowed for products intended for the North American market.
Regulatory Requirements (FCC/IC)
If intended for the North American market the following regulatory requirements
apply:
1) ELWAN1 needs to be labeled with the FCC ID and Canada number:
FCC ID: U99EWLAN2
IC: 4019A-EWLAN2
2) The host product need to be labeled as below:
This device complies with Part 15 of the FCC Rules and Industry
Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
Contains Transmitter Module
FCC ID: U99EWLAN2
IC: 4019A-EWLAN2
3) The user guide of the host equipment shall contain the following
information:
FCC note:
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
Page 7 of 9
Integration Information
FCC ID: U99EWLAN2
IC: 4019A-EWLAN2
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Note: The following paragraph is valid for devices labeled with
FCC ID: U99EWLAN2 and IC: 4019A-EWLAN2:
Important note: This equipment complies with FCC and IC RSS-102 radiation exposure
limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 50 cm (19.7 in, applied to a 18 dBi antenna) between the
radiator and your body. The antenna used for this transmitter must not be co-located with
any other transmitters within a host device, except in accordance with FCC multitransmitter product procedures.
This transmitter is restricted to indoor use only within the 5.15-5.25 GHz band to reduce
potential for harmful interference to co-channel mobile satellite systems.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique
de la classe B est conforme à la norme NMB-003 du Canada. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (EIRP) is not more than that permitted for
successful communication.
This device has been designed to operate with the antennas listed below having a
maximum gain of 18 dBi:
Antennas operating with this device model:
BAT-ANT-RSMA-2AGN-R (1)
BAT-ANT-N-3AGN-IP67
BAT-ANT-N-MiMoDB-5N-IP65
BAT-ANT-N-MiMo5-9N-IP65
BAT-ANT-N-8G-DS-IP65
BAT-ANT-N-MiMo-18N-IP65 (2)
2.4 GHz Band
Yes
Yes
Yes
No
Yes
No
Permitted band of operation
5.15-5.25 GHz Band
5.725-5.825 GHz Band
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
Yes
Antennas not included in this list are prohibited for use with this device. The required
antenna impedance is 50 ohms.
Page 8 of 9
Integration Information
FCC ID: U99EWLAN2
IC: 4019A-EWLAN2
Note (1): When using three antennas of the type BAT-ANT-RSMA-2AGN-R, each
antenna has to be aligned into a separate spatial direction (x-y-z), where one antenna is
perpendicular to the device and the other two are at right angles to each other.
Note (2): Antenna BAT-ANT-N-MiMo-18N-IP65 has to be connected to the WLAN main
unit as below:
Antenna port “Ver” to WLAN antenna port 1
Antenna port “+45” to WLAN antenna port 2
Antenna port “-45” to WLAN antenna port 3
Other connection combinations are not permitted.
Page 9 of 9

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 9
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:8e7543ec-79e6-11e3-0000-da024b9ab37b
Producer                        : GPL Ghostscript 9.07
Keywords                        : ()
Modify Date                     : 2014:01:07 12:01:22+01:00
Create Date                     : 2014:01:07 12:01:22+01:00
Creator Tool                    : PDFCreator Version 1.7.1
Document ID                     : uuid:8e7543ec-79e6-11e3-0000-da024b9ab37b
Format                          : application/pdf
Title                           : U99EWLAN2_integration_manual
Creator                         : rxb12011
Description                     : ()
Author                          : rxb12011
Subject                         : 
EXIF Metadata provided by EXIF.tools
FCC ID Filing: U99EWLAN2

Navigation menu