Hisense Electric LCDF0027 Part15 Subpart B-LED LCD TV User Manual ES G132903

Download:
Mirror Download [FCC.gov]
Document ID	2062394
Application ID	+7zbxpHSGn7ZT9A3tFr7Rg==
Document Description	W9HLCDF0027_User Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	402.96kB (5036942 bits)
Date Submitted	2013-09-05 00:00:00
Date Available	2013-09-06 00:00:00
Creation Date	2013-08-27 15:52:48
Producing Software	Corel PDF Engine Version 9.397
Document Lastmod	2013-08-27 15:52:58
Document Title	ES-G132903Ó¢ÎÄ
Document Creator	CorelDRAW Version 9.397
Document Author:	΢ÈíÓû§

Getting Started
Installing Batteries in the Remote Control
:- Change the batteries
1. Slide the back cover to open the battery compartment of the remote control.
2. Insert two AAA size batteriest Make sure to match the (+) and ( - ) ends of the batteries with the (+) and ( - ) ends indicated in
the battery compartment.
3. Close the battery compartment cover.
The remote control requires: 0 Gently push and slide 0 Insert the batteries 9 Gently push and slide
' Number of Batteries: 2
o Type: AAA
0 Voltage: 1.5Vcc
Dispose of your batteries in a designated disposal area. Do not throw the batteries into a fire.
Do not mix battery types or combine used batteries with new ones.
Remove depleted batteries immediately to prevent battery acid from leaking into the battery compartment.
It you do not intend to use the remote control for a long time. remove the batteries.
Batteries should not be exposed to excessive heat, such as sunshine, heat registers, or fire.
9’9".“9’Nr‘
Battery chemicals can cause a rash. If the batteries leak, clean the battery compartment with a cloth. Ii chemicals touch your
skin, wash immediately.
7. Do not mix old and new batteries.
8. Do not mix alkaline, standard (carbon»zinc) or rechargeable (ni-cad, ni»mh, etc.) batteries.
Program Your Universal Cable or Satellite Remote Control to Operate Your New Hisense Television!
If you would like to program your other household remote controls to your new Hisense television,please consult the User's
Manual supplied by your Cable or Satellite provider. The Cable or Satellite providers' User‘s Manuals should include instructions
on how to program their remote to your television,
Below is a list of Hisense codes for the most common Cable and Satellite providers. Use the Hisense code that is associated
with your Cable or Satellite provider (ii applicable).
DIRECTV ............. .....,..01780r10019
Time Warner Cable ................ 386 or 0178
Comcast... ..... 0178 or 10178
Cox Communications ...... ,.0178
Dish Network
AT&T U-verse 346
If the Hisense code associated with your Cable or Satellite provider is not listed above,if the code above does not work, or it
you cannot locate the instructions for programming your household remote to your television,ca|| your local Cable or Satellite
provider’s customer service center.
:- The effective range of remote control
1. The remote control distance: 315 inches in front of the TV set.
2. The remote control angle: taking the television infrared light receiver window as an apex, 236 inches away, its controlled
angle (left to right) is within 30 degrees, while the vertical angle (up to down) is within 30 degrees.
Gett ng Started
Making connections
I Check the jacks for position and type before making any connections. Loose connections can result in image or color
problems. Make sure that all connections are tight and secure.
0 Not all AN devices have the ability to connect to a TV' please refer to the user manual of your A/V device for compatibility
and connections procedure.
I Always unplug the power cord when connecting external equipment.
:- Connecting an antenna, cable or cable/satellite box
1. Turn off the TV before connecting the antenna.
2. Connect one end of a coaxial cable (not included) to the RF OUTjack on the antenna, cable or cable/satellite box. If you are
using an antenna with twin-lead cable, you may need a 300-75 ohm adapter (not provided) to connect it to the back of your
TV. Likewise, it you are using several antennas, you may need a combiner (not provided).
3. Connect the other end of the cable to the ANT/CABLE jack on the side of your TV.
TV JACK EXTERNAL DEVICES
VHF/UHF Antenna
:- Connecting an AN Device with Composite Cable
1, Use the audio and video cables to connect the external A/V device's composite video/audio jacks to the TVs jacks. (Video =
yellow, Audio Left = white, and Audio Right = red)
2. Plug the connected devices into the mains socket before switching on the TV.
3. Select the corresponding source from the TV.
EXTERNAL DEVICES
White(L)
AV Cable While(L)
(not included)
Yellowwideo)
Velloledeo)
mm. m
Equipment wnh AN lam
Gett ng Started
:- Connecting an AIV Device with Component (YPBPR) Cable
1. Use a component cable to connect the external AN device's component output jacks to the TVs YPEPR jacks. Use an audio
cable to connect the external A/V device's component audio jacks to the TVs AUDIO (LIleacks.
2. Plug the connected devices into the mains socket before switching on the TV.
3. Select the corresponding source from the TV.
EXTERNAL DEVICES
TV JACK
Red R
Red R
White L Audio Cable
(not included) White L
we»:
Cowonent/
Equipment with AN jacks
:- Connecting an AIV Device with HDMI Cable
0 Support digital connections between HDMI - I
enabled AN devices such as PVR, DVD, BIu-ray, EXTERNAL DEVICES
AV receiver and digital devices.
I Some devices such as PVR or DVD player require in
HDMI signal to be set to output in the device's settings. HDM‘ cable I DVD“ R m
0 Please consult your device user manual lor (notincluded)
instructions.
Samoa!
1. Use an HDMI cable to connect the A/V device's
HDMI outputjack to the TVs HDMI jack.
2. Plug the connected devices into the mains socket before switching on the TV .
Equipment with HDMl iacks
3. Select the corresponding source from the TV.
The HDMI connector provides both video and audio signals, it’s not necessary to connect the audio cable.
:- Connecting an MHL-enabled device
You can connect an MHL-enabled device, such as a cell phone or ‘ TV JACK
Roku Streaming Stick”. and view your device‘s screen on the TV.
1. Connect one end 01 an HDMI-to-MHL cable to the micro USB
port on the device.
2. Connect the other end ofthe cable to the HDMI / MHLiack.
3. Select the corresponding source from the TV.
This feature may not be available, depending on your TV series.
Not all cell phones support MHL leature as this only works with MHL enabled phone.
E 1! :- umwwmma
x. E (not Inclmdi
3' Connecting a headphone ' TV JACK EXTERNAL DEVICES
Headphones can be connected to the 0/AUDIO OUT output I
on your set. (While the headphone is connected, the sound film"
from the built-in speakers will be disabled.)
Gett ng Started
:- Connecting an Audio Receiver with Audio cable
1. Use an audio cable to connect the A/V device's digital audio in jack to the TVs DIGITAL OUTPUTjack, Or use an RCA Y-cable
(1/8"-stereo mini to UR phono - not provided) to connect analog sound system to the TVs O/AUDIO OUT jack.
2. Plug the connected devices into the mains socket before switching on the TV.
3. Select the corresponding source from the TV.
TV JACKS
EXTERNAL DEVICES
menu
0 Audio Cable
(not included)
R 555515! I
wmts L MUM!“
(not Included) am am
0 When a digital audio system is connected to the DIGITAL AUDIO OUT (Optical) jack, decrease the volume oi both the TV
and the system.
0 51 CH (channel) audio is available when the TV is connected to an external device supporting 5.1 CH,
I When the receiver (home theater) is set to on, you can hear sound output from the TVs digital audio out jack. When the TV
is receiving a DTV signal, the TV will send 5.1 CH sound to the home theater receiver. When the source is connected to the
TV via HDMI, only 2 CH audio will be heard from the home theater receiver. If you want to hear 5.1 CH audio, connect the
digital audio out jack from your DVD/BIu-ray player/cable box/STB satellite receiver directly to an amplifier or home theater.
Turnlng YOU I' TV on or Off r If Auto selected. the options of Year/Montthay/Tirne are
not available.
To turn yourTV on croft (standby mode): r Setting the Time: Press [4w] to select the number you
1 Plug the power cord into an AC power outlet. want to set and press [A/V] to set.
2. Press [POWER] button YourTVturns 0” 4, Press [A/V] to select your Picture Mode: Home Mode or
3, Press [POWER] button again to turn off your TV When Retail Mode, press [ENTER] button to Confirm.
you turn off your TV, it goes into standby mode
(D WARNING
When your TV is in standby mode. it is still receiving RetailMode
Power- To CompIeIer discomec‘ ”we" “"pIug the WW” Human... anion-WW» “minimum is
cord. '
B NOTE
If your TV does not receive an input signal for several
minutes, lI automatically 9°95 ”“0 standby mode. If you select Retail Mode, a message appears “Are you
. . . sure you want retail mode?" Select “Yes" to continue, or
Tl] mlng the TV on for the FIrSt Tlme select “No" to change your selection.
. . 5 Press [A/V] to select your TV Source' Antenna or Cable,
The Setup Wizard menu appears the first time you turn press [ENTER] button to confirm.
on the TV. It Will assist you to specily the rnenu language,
Picture Mode, TV Source and Channel Installation
IMPORTANT: Make sure that the antenna or cable is
connected.
1. Make sure that you have:
Installed batteries into the remote Control .
Connected an antenna or cable
Connected the power cord
2» Connect your TV'5 power cord to a Power Outlet, the" c Then your TV automatically starts Channel installation
press power. The initial setup screen opens. Press [A/V]
button to select your language, press [ENTER] button to
confirm
available in your Viewmg area.
u Analog Lhannels
an m
nrrlltrt.
‘ Depending on the reception condition, it may take several
3, Press [A/V] to select your options and press [] to minutes to scan channels. Please allow the process to
set the options, complete without interruption,
r If you press [EXIT] to exit the scanning, a message
appears “Please Run Channel Auto Scan", you should
scan channels from the menu of Channels
Selecting the Input Source
The first time you turn on your TV, you must select the TV
signal source. YourTV stores this information, so you do not
need to change the TV signal source unless it changes. For
example, you change from an outside antenna to cable TV.
To select the video input source:
1. Turn on your TV, then press [INPUT] button on the remote
or on the TV. The Input source menu opens.
2. Press [AIV] button to highlight the input source, then
press [ENTER] button.
Changing Channels l Volume
1. Press the [CH NV] (or [CH +/,]) on the TV/remote control
to change the channel
2. Press the [VOL NV] (or [VOL +/-]) on the TV/remole
control to adlust the volume.
3. Press the numeric buttons on the remote control to
display the corresponding channels.
Changing the channels can also be achieved by directly
entering the channel number using the numeric keys on
the remote control. If you are entering a two or three digit
channel number, the time between key presses should be
less than 3 seconds
Shortcuts Instructions
Aspect - Select the screen aspect ratio from Normal, Wide,
Auto, Zoom and Cinema.
Normal: The original 4:3 aspect
ratio (1.33:1 signal) is preserved, O 0
so black bars are added to the left 0
and right of the image. Standard TV 0
broadcasts are displayed with a 4:3
aspect ratio.
Wide: When watching a standard
broadcast or fullrframe movie in
this mode, the display image is O
stretched proportionately to fill
the TV screen When watching a
widescreen (1.78:1 signal) program
or movie, the display image fills the
TV screen.
Auto: Automatically adlusts the
image based on the screen size and
the TV program.
Zoom: Stretch the 4 3 aspect ratio
image vertically and horizontally to
fill the screen at 1:1 78 aspect ratio.
cinema: Stretch the 4.3 aspect ratio
image vertically and horizontally to
fill the screen at 1.2 35 aspect ratio.
o n
The aspect ratio varies with different sources.
Picture - Press to set the picture mode. It can be set as
Vivid. Standard, Theater, Energy Savings or Custom This
mode achieves a certain image display effect by setting the
brightness, contrast and color etc
Sound - Press to set the sound mode. lt can be set as
Standard, Theater, Music, Speech and Custom.
Mute - Press to turn the sound off, press this button again
to turn the sound back on. This function is used to switch off
sound temporarily.
Sleep - It can set the TV to let it enter into the Standby
state automatically. Press this button repeatedly to select
the proper sleeping clock mode, and the clock tells you the
remaining time before the TV enters Standby state.
Display - Display the information banner The information
including channel number. channel name, current system
time, tuner mode, audio stream. video format. audio
language, closed caption mode, parental locks rated,
program details. etc.
To Use the Menu
Press [MENU] to open the main menu.
Press [A/V] to select a menu option. then press [VI
ENTER] button to enterthe menu.
in each menu, you can-
Press [A/V] to select an item,
Press [] to ad]ust the value, or
Press [VIENTER] to enter the submenu,
Press [MENU] to back the previous menu.
4 Press [EXIT] to exit the menu.
B NOTE
Standard 0
—i I— an
_l l— 50
Colai —i I— so
Tint _l l— i]
—l i._ 50
The menus in the user manual may vary slightly from the actual screen.
Using the Picture Menu
Firture Mode
Brightness
Curitra§|
Color —i l— 50
Standard 4}
_] l— 50
—l i._ 50
‘fint —i l— D
Sharpne
Advanced VIdEO
P “re Settings
_] l— 50
You can adjust:
Picture Mode - Ad]ust the Picture Mode. You can select
Vivid, Standard, Theater, Energy Savings or Custom.
Brightness - lncrease or decrease the brightness of the
picture Increasing the brightness can add more light to dark
areas of the picture, while decreasing the brightness can
add more darkness to light areas of the picture.
Contrast - Increase or decrease the contrast oir the picture.
Increase the contrast to ad]ust the white areas of the picture
or decrease the contrast to adjust the black areas of the
picture
Color - Adjusts the color intensity of the picture. A low
setting may make the color look faded A high setting may
make the color look artificial
Tint - Adjusts the color balance of the picture Use this
control to make skin tones look more natural
Sharpness - You can increase the sharpness level for clearer
images or decrease the sharpness level for smoother images.
Advanced Video - Access advanced video settings such as
Backlight, Color Temperature and Noise Reduction.
Dynamic Backlight Control: Enhances the contrast
ratio between light and dark areas of the picture. You can
select Off, Low, or High
Backlight: Sets the overall brilliance of the screen, When
the option of Dynamic Backlight Control is turned Low
or High, you cannot change the Back Light setting,
Aspect Ratio: To choose the screen aspect ration from
Wide, Cinema,Auto, Normal, 1:1 PIXEL MAP and Zoom.
3 NOTE
The option of the screen Aspect Ration is different in
different inputs. (For more information, see “Shortcuts
lnstructions")
Color Temperature: Change the color temperature. You
can select the color temperature from three options: Cool,
Normal or Warm.
Overscan: Ad]usts the picture's reproduction rate, You
can select On or Off.
3 NOTE
Only available in DTV, Component and HDMI(YUV)
source.
Noise Reduction: Select to reduce the noise level of
connected equipment off, Low, Medium and High
Adaptive Contrast: Automatically ad]usts picture detail
and brightness. You can select On or Off.
120Hz Effect: Inserts frames to reduce ]udder in fast
action scenes You can select On or Off.
B NOTE
Only available in the models that support 120 Hz.
Reset Picture Settings - Resets all Picture Settings to the
factory defaults
I;
Using the Audio Menu
Auto Volume Continl
TV Speakers
Advanced Audio
Reset Audio Settings
W 1- ,. lJir‘
Adlust settln s to affect sound quality
You can adjust:
Sound Mode - Select the Sound Mode: Standard, Theater,
Music, Speech or Custom.
Balance -Adjust the volume of the left and right speakers,
Equalizer - Soften or enhance the sound at specific
frequency points.
Auto Volume Control , Automatically adjusts volume to a
consistent level, attenuates loud passages
TV Speakers - Selects where to play TV audio. You
can select On (default selling) to play audio through TV
speakers. or select Off to play audio through the speakers
on an external audio system.
Advanced Audio , Access Advanced Audio settings such as
Digital Audio Out, MTS/SAP, Audio Language
Stereo.
English 9
MTSi‘SAP
Audio Language
Digital Audio Out: Send digital audio to an external
audio system. You can select PCM or RAW.
, PCM: PCM outputs two channel audio regardless of
the input format.
c RAW: When the data stream carries Dolby signal,
digital SPDIF outputs Dolby data stream, When the
data stream carries no Dolby signal, it transports PCM
data stream.
MTSISAP (Analog channels only): Select the default
audio stream. you can select Mono. Stereo or SAP
(Second Audio Program).
’ Mono: Select this option if there is noise or static on
Weak stereo broadcasts.
“ Stereo: Select this option for programs broadcast in
stereo
’ SAP: Depending on the particular program being
broadcast. you can listen to a foreign-language
translation.
Audio Language (Digital channels only) - Change the
default value for audio language.
Reset Audio Settings - Resets all audio settings to the
factory defaults
Using the Channels Menu
Antenna 4}
runei mode.
Auto Channel ‘earch
Channel Skip
Favorite List
Channel Labels
ATOSVI p
signal Strength >
Audio 0an on»
ma. , w w is Eat
You can adjust:
Tuner Mode - Select the TV signal source You can select
Antenna or Cable
Auto Channel Search - Scans for channels that have
signals and stores the channels information in memory.
Scanning for Channels
Antenna
Siam. canning
Digital ciiaiiii n
Analog nnnels l)
_4 i
Digital Channels: The scanned TV program in digital
signals.
Analog Channels: The scanned TV program in analog
signals
Channel Skip - You can hide channels in the channel list.
Press [A/V] to select the channels you want to hide and
press [ENTER] to confirm.
l lSArATDSJ
D 17
l l29
D45
Manual add and 5le channels in your pi ran

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : ΢ÈíÓû§
Create Date                     : 2013:08:27 15:52:48+08:00
Modify Date                     : 2013:08:27 15:52:58+08:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2013:08:27 15:52:58+08:00
Creator Tool                    : CorelDRAW Version 9.397
Format                          : application/pdf
Title                           : ES-G132903Ó¢ÎÄ
Creator                         : ΢ÈíÓû§
Document ID                     : uuid:469049ea-0985-4ba6-ae60-3f75e34779e7
Instance ID                     : uuid:9fdc143d-fd63-477e-a806-06cc53899f85
Producer                        : Corel PDF Engine Version 9.397
Page Count                      : 8

EXIF Metadata provided by EXIF.tools