W10511590 A 说明书 XQG70 HA1224 WFHV6012 User Manual
2018-10-05
: Hisense Wfhv6012-User-Manual WFHV6012-User-Manual 10 2018 uploads
Open the PDF directly: View PDF 
.
Page Count: 11
| Download | |
| Open PDF In Browser | View PDF |
USER’S OPERATION MANUAL X08060287B Before operating this unit, please read this manual thoroughly, and retain for future reference NOTE The manufacturer reserves the right for any modifications on the product which might be deemed necessary or useful without informing about it in this IFU. Thank you for choosing a Hisense washing machine. Before operating your new washing machine, please read this instruction carefully, and keep it for future reference. Please make sure the socket is grounded securely, the water source connection is reliable. The manufacturer declines all liability and warranty for damage to property or injury to persons or animals due to non-compliance with the directions given in this instruction. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. The new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused. This appliance can be used by children aged from 8 years and above and persons with reduced physical. Sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Children of less than 3 years should be kept away unless continuously supervised. The maximum permissible inlet water pressure, 1 MPa, for appliances intended to be connected to the water mains. The minimum permissible inlet water pressure, 0.1 MPa, if this is necessary for the correct operation of the appliance For washing machines with ventilation openings in the base, that a carpet must not obstruct the openings. 1 ensure Ensure Ensure that the ventilation openings in the base of the washing machine (if available on your model) are not obstructed by a carpet or other material. Single inlet Dual inlet - only and cold 2 that ing that the The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for there cyclingof electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. en the from the mains supply, , 3 4 Clean the outside of the washing machine with a damp cloth. Do not use abrasive detergents. Never open the door forcibly or use it as a step. BEFORE THE FIRST WASH CYCLE To remove any residual water used during testing by the manufacture r, we recommend that you carry out a short wash cycle without laundry. 1 Open the tap. DESCRIPTION OF THE WASHING MACHINE 2 Close the door. 3 Pour a little detergent (about 30 ml) into the main wash chamber gent dispenser . 1 1 of the deter- 2 2 4 4 4. Select and start a short programme (see separate quick reference guide). PREPARATION OF THE WASHING 1. Sort the laundry according to... Type of fabric / care label symbol 7 7 Cottons, mixed fibres, easy care/synthetics, wool, handwash items. Control panel layout and appearance will depend on the model. while the can for to be The wool wash cycle of this machine has been tested and approved by The Woolmark Company for the washing of Woolmark garments labelled as “machine wash” provided that the garments are washed according to the instructions on the is while the for is garment label and those issued by the manufacturer of this washing machine. Colour Separate coloured and white items. Wash new coloured articles separately. Loading Wash items of different sizes in the same load to improve washing efficiency and distribution in the drum. Delicates Wash small items (e.g. nylon stockings, belts etc.) and items with hooks (e.g. bras) in a cloth bag or pillow case with zip. Always remove curtain rings or wash curtains with the rings inside a cotton bag. 2. Empty all pockets Coins, safety pins etc. can damage your laundry as well as the appliance drum and tub. 3. Fasteners Close zips and fasten buttons or hooks; loose belts or ribbons should be tied together. Stain removal Blood, milk, eggs etc. are generally removed by the automatic enzyme phase of the programme. 5 6 . / soak U 7 8 2 Depending on the model, Insert removal tool like slotted screwdriver into the small opening of bottom baffle, press the bottom baffle downward with much strength and open it. Or, push down on the tabs provided on both the sides and remove it. unds 9 10 fit fit 11 12 solv no screen are off. and Choose the desired programmme to start the machine. The washing machine will not start, and the screen flashes. Check if the water tap is closed. remove some the screen is flashing. Press the the screen is flashing. too 13 14 Hot / Cold fill fault - For Models with Dual Inlets Fault Code List If you wish to connect hot and cold water supply (Fig.1): 1. Fix the red marked inlet hose to the hot water tap and to the inlet valve with the red filter on the rear side of machine. 2. Fix the other inlet hose to the cold water tap and to the inlet valve with the blue filter on the rear side of the machine. Make sure: a) The connections are tightly fixed b) Do not invert their position (for example: cold fill into hot inlet valve and vice versa). If you wish to connect only the cold fill follow the below instructions (Fig. 2): 1. You will need a Y-piece connector. This can be purchased from local hardware or plumb ing supplier. 2. Fix the Y-piece connector to the cold fill tap. 3. Connect the two inlet valves present on the rear part of the machine to the Y-piece connector using the hoses provided. Ensure that: All connections are tightly fixed. Do not allow children to operate, crawl on, be near or inside your washer. Note that during the wash cycles, the surface temperature of the porthole door may increase. Close supervision of children is necessary when the appliance is used near children. Hot fill Y-piece Red inlet valve Red inlet valve Blue inlet valve Blue inlet valve Fig.1 15 Cold fill Cold fill Displayed on Display Window Fault Description “F01” Water inflow fault “F03” Drainage fault “F04”, “F05”, “F06”, “F07”，“F23” and “F02/F24” Electronic module fault, overflow or too much foam. “F13” Door lock fault “F14” Door unlock fault “Unb” Unbalance alarm a. “F01” displayed on screen The machine is not fed with water or insufficient water. Check: • Faucet is fully open and has enough water pressure. • Water inlet pipe is knotted or not. • Filtering net of water inlet pipe is blocked or not (refer to maintenance and repair). • Water pipe is frozen or not. Press “Start/Pause” key after fault is removed. If fault occurs again, please contact with after-sale service (refer to after-sale service.). b. “F03” displayed on screen The washer is not emptied. The washer stops the program being executed. Shut down the machine and disconnect power supply. Check: • Drain pipe is knotted or not. • Filter in drain pump is blocked or not (refer to the cleaning of filter in drain pump) Ensure that Fig.2 16 C. Fault code The washer stops when the program is running. The display window shows fault code “F02/F24”, fault codes from “F04’ to “F07”, “F13”,“F14”, “F23” or “Unb”. If fault code “F02/F24” is shown Water level reaches overflow level. Remove it by pressing “Start/Pause” key and feed water. Select and start required program. If fault occurs again, disconnect power supply and contact with after-sale service. If fault code “F04” to “F07”, “F23” shown Electronic module fails. Turn the nub to Off for 3 seconds to turn off the machine. After fault is removed, press “Start/Pause” key. If fault occurs again, disconnect power supply and contact with after-sale service. If fault code “F13” is shown Door lock is abnormal. Start program for 20 sec and unlock the washer door (PTC) to check whether the door is closed. Open and close it again. After fault is removed, press “Start/Pause” key. If fault occurs again, disconnect power supply and contact with after-sale service. adequate for the machine’s 10 A Current Rating. The electrical power cable must be replaced exclusively by a licensed electrician. If fault code “F14” is shown Door open fault.. Action: Press “Start/Pause” button. The washing machine will try to open the door. The alarm will not be removed until the door is unlocked. Or, turn the nub to Off for 3 seconds to turn off the machine. Choose the desired programmme to start the machine. The alarm will be removed. If fault code “Unb” is shown Unbalance alarm. Turn the nub to Off for 3 seconds to turn off the machine. Open the door and re-tidy clothes and then rotate program knob to single dehydration mode. Spin clothes to dry again. If fault occurs again, disconnect power supply and contact with after-sale service. 17 18
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Author : NX Create Date : 2012:06:12 11:07:55+08:00 Modify Date : 2018:08:22 09:12:16+01:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08 Producer : Adobe PDF library 9.90 Creator Tool : Adobe Illustrator CS3 Metadata Date : 2018:08:22 09:12:16+01:00 Thumbnail Width : 256 Thumbnail Height : 180 Thumbnail Format : JPEG Thumbnail Image : (Binary data 19699 bytes, use -b option to extract) Rendition Class : proof:pdf Document ID : xmp.did:73A3C7CC3BB4E111AEFE8D5053768D0A Instance ID : uuid:fe22b004-2955-4c22-8318-acf631a6534c Original Document ID : xmp.did:73A3C7CC3BB4E111AEFE8D5053768D0A Derived From Rendition Class : proof:pdf History Action : saved History Instance ID : xmp.iid:73A3C7CC3BB4E111AEFE8D5053768D0A History When : 2012:06:12 11:07:52+08:00 History Software Agent : Adobe Illustrator CS5.1 History Changed : / N Pages : 1 Has Visible Transparency : False Has Visible Overprint : False Max Page Size W : 297.038889 Max Page Size H : 209.902778 Max Page Size Unit : Millimeters Font Name : Arial-BoldMT, ArialMT, TimesNewRomanPSMT Font Family : Arial, Arial, Times New Roman Font Face : Bold, Regular, Regular Font Type : Open Type, Open Type, Open Type Font Version : Version 5.08, Version 5.10, Version 5.07 Font Composite : False, False, False Font File Name : arialbd.ttf, arial.ttf, TIMES.TTF Plate Names : Cyan, Magenta, Yellow, Black Swatch Group Name : 默认色板组 Swatch Group Type : 0 Format : application/pdf Creator : NX Title : W10511590-A-说明书-XQG70-HA1224 Page Count : 11EXIF Metadata provided by EXIF.tools