W10511590 A 说明书 XQG70 HA1224 WFHV6012 User Manual

: Hisense Wfhv6012-User-Manual WFHV6012-User-Manual 10 2018 uploads

Open the PDF directly: View PDF .
Page Count: 11

LAUN

AM NOITAREPO S’RESU

,ylhg

uoroht launam siht daer esaelp ,tinu siht gnitarepo erofeB

ecnerefer erutuf rof niater dna

X08060287

X08060287B

21

ensure

Ensure

Single inlet -

Dual inlet - and cold

only

Ensure that the ventilation openings in the base of the washing machine

(if available on your model) are not obstructed by a carpet or other material.

NOTE

The manufacturer reserves the right for any modifications

on the product which might be deemed necessary or

useful without informing about it in this IFU.

Thank you for choosing a Hisense washing machine.

Before operating your new washing machine, please read

this instruction carefully, and keep it for future reference.

Please make sure the socket is grounded securely, the

water source connection is reliable. The manufacturer

declines all liability and warranty for damage to property

or injury to persons or animals due to non-compliance

with the directions given in this instruction.

If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

The new hose-sets supplied with the appliance are to be

used and that old hose-sets should not be reused.

This appliance can be used by children aged from 8 years

and above and persons with reduced physical. Sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction

concerning use of the appliance in a safe way and

understand the hazards involved.

Children shall not play with the appliance. Cleaning and

user

maintenance shall not be made by children without

supervision.

Children of less than 3 years should be kept

away unless continuously supervised.

The maximum permissible inlet water pressure, 1 MPa,

for appliances intended to be connected to the water

mains.

The minimum permissible inlet water pressure, 0.1 MPa, if

this is necessary for the correct operation of the appliance

For washing machines with ventilation openings in the

base, that a carpet must not obstruct the openings.

34

that

the

ing

en

the

from the mains supply,

,

The symbol on the product, or on the documents accompanying the product,

indicates that this appliance may not be treated as household waste. Instead it

shall be handed over to the applicable collection point for there cyclingof electrical

and electronic equipment. Disposal must be carried out in accordance with local

environmental regulations for waste disposal. For more detailed information about

treatment, recovery and recycling of this product, please contact your local city

office, your household waste disposal service or the shop where you purchased

the product.

that

Control panel layout and

appearance will depend on the model.

56

Clean the outside of the washing machine with a damp cloth. Do not use abrasive

detergents.

Never open the door forcibly or use it as a step.

1. Sort the laundry according to...

Type of fabric / care label symbol

Cottons, mixed fibres, easy care/synthetics, wool, handwash items.

The wool wash cycle of this machine has been tested and approved by The

Woolmark Company for the washing of Woolmark garments labelled as “machine

wash” provided that the garments are washed according to the instructions on the

garment label and those issued by the manufacturer of this washing machine.

Colour

Separate coloured and white items. Wash new coloured articles separately.

Loading

Wash items of different sizes in the same load to improve washing efficiency and

distribution in the drum.

Delicates

Wash small items (e.g. nylon stockings, belts etc.) and items with hooks (e.g. bras)

in a cloth bag or pillow case with zip. Always remove curtain rings or wash curtains

with the rings inside a cotton bag.

2. Empty all pockets

Coins, safety pins etc. can damage your laundry as well as the appliance drum and

tub.

3. Fasteners

Close zips and fasten buttons or hooks; loose belts or ribbons should be tied

together.

Stain removal

Blood, milk, eggs etc. are generally removed by the automatic enzyme phase of the

programme.

To removeanyresidualwater usedduring testing by themanufacturer, we

recommend that you carry out a short wash cycle without laundry.

1 Open the tap.

2 Close the door.

3 Pour a little detergent (about 30 ml) into the main wash chamber of the deter-

gent dispenser .

4. Select and start a short programme (see separate quick reference guide).

BEFORETHE FIRSTWASHCYCLE

PREPARATION OF THE WASHING

DESCRIPTION OF THE WASHINGMACHINE

while the

while the

is

is

can

for

for to be

7

1

4

2

7

1

4

2

7 8

.

U

/ soak

9 10

unds

2 Depending on the model, Insert removal tool like

slotted screwdriver into the small opening of

bottom baffle, press the bottom baffle downward

with much strength and open it. Or, push down on

the tabs provided on both the sides and remove it.

11 12

fit

fit

13 14

solv

the screen is flashing.

too

remove some

no screen are off.

The washing machine will not start, and the screen flashes.

Check if the water tap is closed.

the screen is flashing. Press the

and Choose the desired

programmme to start the machine.

15 16

Fig.1

Hot fill

Red inlet valve

Blue inlet valve

Cold fill

Red inlet valve

Blue inlet valve

Cold fill

Y-piece

Fig.2

If you wish to connect hot and cold water supply (Fig.1):

1. Fix the red marked inlet hose to the hot water tap and to the inlet valve with the red

filter on the rear side of machine.

2. Fix the other inlet hose to the cold water tap and to the inlet valve with the blue filter

on the rear side of the machine.

Make sure:

a) The connections are tightly fixed

b) Do not invert their position (for example: cold fill into hot inlet valve and vice versa).

If you wish to connect only the cold fill follow the below instructions (Fig. 2):

1. You will need a Y-piece connector. This can be purchased from local hardware or plumb

ing supplier.

2. Fix the Y-piece connector to the cold fill tap.

3. Connect the two inlet valves present on the rear part of the machine to the Y-piece

connector using the hoses provided.

Ensure that:

All connections are tightly fixed.

Do not allow children to operate, crawl on, be near or inside your washer.

Note that during the wash cycles, the surface temperature of the porthole door may

increase.

Close supervision of children is necessary when the appliance is used near children.

Hot / Cold fill fault - For Models with Dual Inlets

Ensure that

Fault Code List

Displayed on Display Window Fault Description

“F01” Water inflow fault

“F03” Drainage fault

“F04”, “F05”, “F06”, “F07”，“F23” and “F02/F24”

Electronic module fault, overflow or too much foam.

“F13” Door lock fault

“F14” Door unlock fault

a. “F01” displayed on screen

The machine is not fed with water or insufficient water. Check:

• Faucet is fully open and has enough water pressure.

• Water inlet pipe is knotted or not.

• Filtering net of water inlet pipe is blocked or not (refer to maintenance and

repair).

• Water pipe is frozen or not.

Press “Start/Pause” key after fault is removed.

If fault occurs again, please contact with after-sale service (refer to after-sale

service.).

b. “F03” displayed on screen

The washer is not emptied. The washer stops the program being executed. Shut

down the machine and disconnect power supply. Check:

• Drain pipe is knotted or not.

• Filter in drain pump is blocked or not (refer to the cleaning of filter in drain pump)

“Unb” Unbalance alarm

17 18

adequate for the machine’s 10 A Current Rating.

The electrical power cable must be replaced exclusively by a licensed electrician.

C. Fault code

The washer stops when the program is running. The display window

shows fault code “F02/F24”, fault codes from “F04’ to “F07”, “F13”,“F14”,

“F23” or “Unb”.

If fault code “F02/F24” is shown

Water level reaches overflow level.

Remove it by pressing “Start/Pause” key and feed water.

Select and start required program. If fault occurs again, disconnect power supply

and contact with after-sale service.

If fault code “F04” to “F07”, “F23” shown

Electronic module fails.

Turn the nub to Off for 3 seconds to turn off the machine.

After fault is removed, press “Start/Pause” key. If fault occurs again, disconnect

power supply and contact with after-sale service.

If fault code “F13” is shown

Door lock is abnormal. Start program for 20 sec and unlock the washer door

(PTC) to check whether the door is closed.

Open and close it again.

After fault is removed, press “Start/Pause” key. If fault occurs again, disconnect

power supply and contact with after-sale service.

Action: Press “Start/Pause” button. The washing machine will try to open the

door. The alarm will not be removed until the door is unlocked. Or, turn the nub to

Off for 3 seconds to turn off the machine. Choose the desired programmme to

start the machine. The alarm will be removed.

Unbalance alarm.

Turn the nub to Off for 3 seconds to turn off the machine. Open the door and

re-tidy clothes and then rotate program knob to single dehydration mode. Spin

clothes to dry again.

If fault occurs again, disconnect power supply and contact with after-sale service.

If fault code “F14” is shown

Door open fault..

If fault code “Unb” is shown