Hitachi Saw C 10Fr Users Manual C10FR_US_EnglishOnly_PRESS 2004.06.30

Hitachi Saw C 10FR C10FR_OM_6728

C 10FR to the manual 5181ca69-07a5-4ad5-bf78-60accad1a96a

2015-01-24

: Hitachi Hitachi-Saw-C-10Fr-Users-Manual-314146 hitachi-saw-c-10fr-users-manual-314146 hitachi pdf

Open the PDF directly: View PDF .
Page Count: 28

Download
Open PDF In Browser	View PDF

Model

C 10FR

Jobsite Table Saw

INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS
WARNING
Improper and unsafe use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand
this manual before operating the power tool. Please keep this manual available for others before
they use the power tool.

CONTENTS
SECTION
PAGE
Product Specifications ............................................................ 3
Power Tool Safety ................................................................... 4
Table Saw Safety .................................................................... 5
Electrical Requirements and Safety ...................................... 6
Accessories and Attachments ............................................... 7
Tools Needed For Assembly .................................................. 7
Carton Contents ..................................................................... 7

SECTION
PAGE
Know Your Table Saw ............................................................ 9
Assembly and Adjustments ................................................. 10
Operation ............................................................................... 17
Maintenance .......................................................................... 21
Troubleshooting Guide ......................................................... 22
Push Stick Pattern ................................................................. 23
Parts List ................................................................................ 24

HITACHI AUTHORIZED SERVICE CENTERS
Service under this warranty is available from Hitachi Koki U.S.A., Ltd. at :
IN THE U.S.A.
IN CANADA

6395 Kestrel Road Mississauga, ON L5T 1Z5

3950 Steve Reynolds Blvd. Norcross, GA 30093
9409 Owensmouth Ave. Chatsworth, CA 91311

OR CALL: (800) 546-1666 for a service center nearest you. OR CALL: (800) 970-2299 for a service center nearest you.

— 2—

WARNING
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals
known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks, cement and other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals, work in a well-ventilated area and work with approved safety equipment such as dust masks that are
specially designed to filter out microscopic particles.

PRODUCT SPECIFICATIONS
MOTOR
HP (Maximum developed) ............ 3.0
Type ................................................ Universal
Amps .............................................. 15
Voltage ........................................... 120
Hz .................................................... 60
RPM (no load) ................................ 5000
Overload Protection ...................... YES

SAW
Table Size ....................................... 26-1/16” x 19-21/64”
Table Extensions ........................... 2- Right, Rear
Extension Fence Capacity ............. 24” Right
Blade Size ....................................... 10”
Rip Scale ........................................ YES
Rip Fence ........................................ YES
Miter Gauge ................................... YES
Maximum Cut Depth @ 90° .......... 3-1/8”
Maximum Cut Depth @ 45° .......... 2-1/2”
Net Weight ..................................... 64.5 LBS

WARNING
To avoid electrical hazards, fire hazards or damage to the table saw, use proper circuit protection.
This table saw is wired at the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere time
delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any
way.
Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow these rules
could result in serious injury to you or damage to the table saw.

—3—

POWER TOOL SAFETY
WARNING
Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow these rules
could result in serious injury or damage to the table saw.
Good safety practices are a combination of common
sense, staying alert and understanding how to use your
power tool. To avoid mistakes that could cause serious
injury, do not plug in your power tool until you have read
and understood the following safety rules:
1.

READ and become familiar with this entire Operator’s
Manual. LEARN the tool’s applications, limitations and
possible hazards.

16. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN THE POWER “OFF”. Do not leave the tool
before it comes to a complete stop.
17. NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is
unintentionally contacted.

WARNING
Look for this symbol that identifies important safety
precautions. It means CAUTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED!

15. REMOVE ADJUSTING KEYS AND WRENCHES.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before
turning ON.

18. DO NOT OVERREACH. Keep proper footing and
balance at all times.

NEVER OPERATE THIS MACHINE WITHOUT THE
SAFETY GUARD IN PLACE FOR ALL THROUGH
SAWING OPERATIONS.

19. MAINTAIN TOOLS WITH CARE. Keep tools sharp and
clean for most efficient and safest performance.
Follow instructions for lubricating and changing
accessories.

DO NOT USE IN A DANGEROUS ENVIRONMENT
such as damp or wet locations or exposure to rain.
Keep work area well lighted.

DO NOT use power tools in the presence of flammable
liquids or gases.

KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.

KEEP CHILDREN AWAY. All visitors should be kept at
a safe distance from the work area.

DO NOT FORCE THE TOOL. It will do the job better
and safer at the rate for which it was designed.

USE THE RIGHT TOOL. Don’t force the tool or
attachment to do a job for which it is not designed.

20. CHECK FOR DAMAGED OR LOOSE PARTS.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to ensure
it will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, loose mounting and any
other conditions that may affect its safe operation. A
guard or other part that is loose or damaged should
be properly adjusted repaired or replaced.
21. MAKE WORKSHOP CHILD PROOF with padlocks,
master switches or by removing starter keys.
22. DO NOT operate the tool if you are under the
influence of any drugs, alcohol or medication that
could impair your ability to use the tool safely.

10. WEAR PROPER APPAREL. DO NOT wear loose
clothing, gloves, neckties, rings, bracelets or other
jewelry that may get caught in moving parts. Non-slip
footwear is recommended. Wear protective hair
covering to contain long hair.

23. USE DUST COLLECTION SYSTEM wherever possible.
Dust generated from certain materials can be
hazardous to your health and in some cases, a fire
hazard. Always operate the power tool in a wellventilated area with adequate dust removal.

11. WEAR A FACE MASK OR DUST MASK. Sawing,
cutting and sanding operations produce dust.

24. ALWAYS WEAR EYE PROTECTION. Any power tool
can throw foreign objects into your eyes that could
cause permanent eye damage. ALWAYS wear safety
goggles (not glasses) that comply with ANSI safety
standard Z87.1. Everyday glasses have only impact
resistant lenses. They ARE NOT safety glasses.
NOTE: Glasses or goggles not in compliance with
ANSI Z87.1 could cause serious injury when they
break.

12. DISCONNECT TOOLS before servicing and when
changing accessories such as blades, cutters, etc.
13. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure the switch is in the OFF position before
plugging into the power supply.
14. USE ONLY RECOMMENDED ACCESSORIES.
Consult the Operator’s Manual for recommended
accessories. The use of improper accessories may
cause injury to you or damage to the tool.

25. DIRECTION OF FEED. Feed work into a blade or cutter
against the direction of rotation of the blade or cutter
only.

—4—

TABLE SAW SAFETY
1.

ALWAYS USE SAW BLADE GUARD, splitter and antikickback pawls for every operation for which they can
be used, including through sawing. Through sawing
operations are those in which the blade cuts
completely through the workpiece when ripping or
crosscutting.

ALWAYS HOLD WORK FIRMLY against the miter
gauge or rip fence.

USE A PUSH STICK when required. Always use a
push stick especially when ripping narrow stock. Refer
to ripping instructions in this Operator’s Manual
where the push stick is covered in detail. A pattern for
making your own push stick is included on page 23.

14. AVOID AWKWARD OPERATIONS and hand positions
where a sudden slip could cause your hand to move
into the saw blade.

16. MOUNT your table saw on a bench or stand before
performing any cutting operations. Refer to
ASSEMBLY AND ADJUSTMENTS on page 10.

NEVER STAND or have any part of your body in line
with the path of the saw blade. Keep your hands out
of the saw blade path.

NEVER REACH behind or over the cutting tool for any
reason.

REMOVE the rip fence when crosscutting.

DO NOT USE a molding head with this saw.

FEED WORK INTO THE BLADE against the direction of
rotation only.

11. NEVER ATTEMPT TO FREE A STALLED SAW BLADE
without first turning the saw OFF. Turn power switch
OFF immediately to prevent motor damage.

13. AVOID KICKBACKS (work thrown back towards you)
by keeping the blade sharp, the rip fence parallel to
the saw blade and by keeping the splitter, antikickback pawls and guards in place, aligned and
functioning. Do not release work before it has passed
all the way past the saw blade. Do not rip work that is
twisted, warped or does not have a straight edge to
guide it along the fence.

15. NEVER USE SOLVENTS to clean plastic parts.
Solvents could possibly dissolve or otherwise damage
the material. Only a soft damp cloth should be used to
clean plastic parts.

NEVER PERFORM ANY OPERATION FREE HAND,
which means using only your hands to support or
guide the workpiece. Always use either the fence or
the miter gauge to position and guide the work.
WARNING: FREEHAND CUTTING IS THE MAJOR
CAUSE OF KICK-BACK & FINGER/HAND
AMPUTATIONS.

10. NEVER use the rip fence as a cut-off gauge when
crosscutting.

12. PROVIDE ADEQUATE SUPPORT to the rear and the
sides of the saw table for long or wide workpieces.

17. NEVER CUT METALS or materials which may make
hazardous dust.
18. ALWAYS USE IN WELL-VENTILATED AREA.
Remove sawdust frequently. Clean out sawdust from
the interior of the saw to prevent a potential fire
hazard. Attach a vacuum to the dust port for
additional sawdust removal.
19. NEVER LEAVE THE SAW RUNNING UNATTENDED.
Do not leave the saw until it comes to a complete
stop.
20. For proper operation follow the instructions in this
Operator’s Manual entitled ASSEMBLY AND
ADJUSTMENTS (Page 10). Failure to provide sawdust
fall-through and removal hole will allow sawdust to
build up in the motor area resulting in a fire hazard
and potential motor damage.

—5—

ELECTRICAL REQUIREMENTS AND SAFETY
POWER SUPPLY REQUIREMENTS

GROUNDING INSTRUCTIONS

WARNING
To avoid electrical hazards, fire hazards or damage to the
table saw, use proper circuit protection. Always use a
separate electrical circuit for your tools. This power tool is
wired at the factory for 120V operation. Connect it to a
120V, 15 Amp circuit and use a 15 Amp time delay fuse or
circuit breaker. To avoid shock or fire, replace the cord
immediately if it is worn, cut or damaged in any way.

EXTENSION REQUIREMENTS

Any extension cord must be GROUNDED for safe
operation.

MINIMUM GAUGE FOR EXTENSION CORDS
(AWG type / 120 Volt only)
Not
More Than More Than
0
6
6
10
10
12
12
16

CHECK with a qualified electrician or service personnel if
you do not completely understand the grounding
instructions, or if you are not sure the saw is properly
grounded.

Total length in feet
25’
18
18
16
14

50’
16
16
16
12

DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the
receptacle, have the proper receptacle installed by a
qualified electrician.
IMPROPER CONNECTION of the equipment grounding
conductor can result in risk of electric shock. The
conductor (wire) with the green insulation (with or without
yellow stripes) is the equipment grounding conductor. If
repair or replacement of the electric cord or plug is
necessary, DO NOT connect the equipment grounding
conductor to a live terminal.

WARNING

Ampere Rating

IN THE EVENT OF A MALFUNCTION OR BREAKDOWN,
grounding provides a path of least resistance for electric
current and reduces the risk of electric shock. This saw is
equipped with an electric cord that has an equipment
grounding conductor and a grounding plug. The plug
MUST be plugged into a matching receptacle that is
properly installed and grounded in accordance with ALL
local codes and ordinances.

100’
150’
16
14
14
12
14
12
Not Applicable

Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole grounding receptacles that
accept the saw’s plug. Repair or replace damaged or
worn cords immediately.
3-Prong Plug

GUIDELINES FOR EXTENSION CORDS
Any extension cord used for power tools MUST be
grounded (3-wire with two flat prongs and one round
ground prong).
Make sure the extension cord is in good condition. When
using an extension cord, make sure you use one heavy
enough to carry the current the tool will draw. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. The table above shows
the correct size to use according to extension cord length
and nameplate ampere rating. If in doubt, use the next
heavier gauge cord. The smaller the gauge number the
heavier the cord.
NOTE: The 12 to 16 Amp rating is correct for this tool. It is
highlighted in the table above.
Be sure your extension cord is properly wired and in good
condition. Always replace a damaged extension cord or
have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Before connecting the saw to the extension cord, make
sure the saw switch is turned OFF.

—6—

Grounding Prong
Properly Grounded
3-Prong Receptacle

Grounding Lug
Make Sure This
is Connected to a
Known Ground
Adapter

2-Prong
Receptacle

ACCESSORIES AND ATTACHMENTS
RECOMMENDED ACCESSORIES

WARNING

Visit your Hardware Department or see the Power and
Hand Tools Catalog to purchase recommended
accessories for this power tool

To avoid the risk of personal injury:
Do not use adjustable (wobble) type dadoes or carbide
tipped dado blades; maximum dado width is 1/2" .
Do not use a dado with a diameter larger than 6" .
Do not use molding head set with this saw.
Do not modify this power tool or use accessories not
recommended by Store.

TOOLS NEEDED FOR ASSEMBLY
TOOLS NEEDED
Medium screwdriver

Adjustable wrench

#2 Philips screwdriver
Straight edge

Combination square

CARTON CONTENTS
UNPACKING AND CHECKING CONTENTS
Separate all parts from packing materials. Check each part
with the illustration on the next page and the "Table of
Loose Parts" to make certain all items are accounted for,
before discarding any packing material.

WARNING
If any part is missing or damaged, do not attempt to
assemble the table saw, plug in the power cord, or turn
the switch ON until the missing or damaged part is
obtained and is installed correctly.

TABLE OF LOOSE PARTS
ITEM

DESCRIPTION

A.
B.
C.
D.
E.
F.

Table saw assembly
Blade
Blade wrenches
Miter gauge
Hex key
Bolt, flat washer, toothed washer,
Oval washer, spring washer
Blade guard and splitter
Rip fence
Rear table extension
Rear table extension tube
Location seat
Dome nuts
Hand wheels
Table extension
Dust collect elbow
Parallel washer hardware

G.
H.
I.
J.
K.
L.
M.
N.
O.
P.

QUANTITY
1
1
2
1
1
1 each
1
1
1
2
4
2
2
1
1
1 each

STAND:
Q.
Stand assembly
R.
Hex. head bolts
S.
Flat washers
T.
Roller wheels
U.
Square neck bolts
V.
Nuts
W.
Support rod

1
4
4
2
2
2
1

Batteries

NOTE: To make assembly easier, keep contents of box
together. Apply a coat of automobile wax to the table.
Wipe all parts thoroughly with a clean dry cloth. This will
reduce friction when pushing the workpiece. To avoid
injury, the styrofoam block should be removed between
the motor and the table.

—7 —

UNPACKING YOUR TABLE SAW

Q
A
T

C
V
F

R
D
N

45
O

DOW

L
M

J
I

N
W

— 8—

KNOW YOUR TABLE SAW
The Front of Table Saw
Blade guard with LED lighting
Cutting line
Miter gauge
indicator
Bevel angle
Pointer & scale
Overload reset
switch

Table Insert
Rip fence
Side table extension
Extension wing
locking lever

Miter gauge
storage

Blade tilting
handwheel

Fence storage

Blade bevel
lock knob

Stand handle

Stand wheel

ON/OFF switch
with key

Blade elevation
handwheel

Lock lever
Support Rod

Stand hook

The Rear of Table Saw

Cord wrap

—9—

ASSEMBLY AND ADJUSTMENTS
ESTIMATED ASSEMBLY TIME 25~40 MINUTES
FOLDING THE STAND (Fig. A-1)
1. Release the stand hook (1).
2. Unfold the wider leg set (2). Pull the lever (3)
downward and push it to lock in place. Then, put
down the wider leg set on the ground.
3. Lift the stand up and unfold the narrower leg set (4).
4. Pull the lever downward and push it to lock in place.
NOTE: Make sure the stand is locked securely.

5.
6.

Tighten all four bolts.
NOTE: Do not over tighten bolts holding saw to stand.
This will damage the saw base.
Carefully set the saw in its upright position on a clean
level surface.
Thread the support rod (10) into the socket (11) at the
rear of stand. Adjust the adjustable foot (12) properly.

Fig. A-2

Fig. A-1

FOLDING THE TABLE SAW/STAND (Fig. A-1, A-3)
1. Release the lever of the narrower leg set and keep the
lever on top. Hold the table and lift the saw up just
above the ground and fold up the narrower leg set.
NOTE: The narrow leg set can be held by a "spring
clip" .
2. Then reposition on the saw onto the ground. Release
the lever of the wider leg and keep the lever on top set
then fold the leg set up into position.
3. Then fix the legs with stand hook.

2
6

ASSEMBLING THE ROLLER WHEEL (Fig. A-1)
Attach the roller wheel (7) to roller wheel bracket using
square neck bolt (8) and nut (9) as shown.
INSTALLING THE DUST COLLECTION ELBOW
(Fig. A-1)
1. Align the dent with the slot on the exhaust port. Install
the dust collection elbow (6) onto the exhaust port.
NOTE: The elbow can be used to attach either the dust
bag or a vacuum hose to remove sawdust from the work
area.

SETTING UP THE TABLE SAW/STAND (Fig. A-3)
1. Release the stand hook.
2. Unfold the wider leg set and lock the lever in place.
3. Put down the wider leg set on the ground, lift the saw
up and unfold the narrower leg set.
4. Pull the lever downward and lock into place.
NOTE: Make sure the saw is locked in position
securely before operation.

Fig. A-3

ASSEMBLING TABLE SAW TO STAND (Fig. A-1,A-2)
1. Place stand on level surface and adjust front right
adjustable stand pad (5) to make stand stable.
2. Place table saw on the top of stand aligning holes in
base with holes in stand.
3. Insert four hex. head bolts (6) through flat washer and
holes in base and stand.

—10 —

FOLDING

SET-UP

SAW MOUNTED TO WORK SURFACE (Fig. B)
1. If the leg set will not be used, the saw must be
properly secured to a sturdy workbench using the four
mounting holes at the base of the saw.
2. The surface of the table where the saw is to be
mounted must have a hole large enough to facilitate
sawdust fall-through and removal.
3. Square the saw on the mounting surface and mark the
location of the four 3/8" mounting holes (1).
4. Drill 3/8" hole into the mounting surface.
5. Mark an 11" square (2) centered between the four
mounting holes (1).
6. Cut out and remove the square.
7. This opening will allow sawdust to fall through the
saw base.
8. Place the saw on the work surface, and align the
mounting holes of the saw with those drilled through
the surface.
9. Fasten the saw to the work surface.

INSTALLING BATTERY FOR LED LIGHTING(Fig. B)
1. Open the cover (1) of battery box on the top of blade
guard.
2. Install 2 pieces of 1.5V 3A batteries into the battery
box in right direction.
3. Close the cover.
4. Turn on the switch (2) to check the LED lighting.

Fig. D

BLADE RAISING HANDWHEEL (Fig. E, F)
1. Attach the handwheel (1) to the elevation screw (2) at
the front of the saw.
Make sure the slots (3) in the hub of the handwheel
engage with the pins (4). (Fig. E)
2. Attach and tighten the dome nut (5) at the end of the
shaft (Fig. F).

WARNING
Do not operate this machine on the floor. This is very
dangerous and may cause serious injury.

Fig. B

Fig. E
S QU A R E
CU T OU T

2
1
3
1

WARNING
Failure to provide the sawdust fall-through hole will cause
sawdust to build up in the motor area, which may result in
fire or cause motor damage.
KEEPING THE AREA CLEAN
1. Sawdust and wood chips that fall from under the saw
will accumulate on the floor.
2. Make it a practice to pick up and discard this dust
when you have completed cutting.

BLADE TILTING HANDWHEEL (Fig. G, F)
1. Attach the other handwheel (6) to the blade tilting
screw on the side of the saw in the same manner as
above.
2. Attach and tighten the handwheel dome nut (5).

Fig. F

ADJUSTING THE CUTTING LINE INDICATOR (Fig. C)
1. Take off the cover (1)by loosening screws (2).
2. Adjust the pointer (3) to align to the blade.
3. Mount the cover on the table to fix the pointer.
NOTE: The pointer was set up to align to the right side of
the blade when packing.

Fig. C

— 11 —

5
6

3. Place the open-end wrench jaws on the flats of the
saw arbor to keep the arbor from turning. (Fig. H) and
place the box-end wrench (8) on the arbor nut (5), and
turn anti-clockwise.
4. Remove the arbor nut (5) and flange (6), remove
blade.
5. Install the saw blade onto the arbor with the blade
teeth pointing toward the front of the saw.
6. Install the flange (6) against the blade and thread the
arbor nut (5) as far as possible by hand. Ensure that
the blade is flush against the inner side of the blade
flange.

RIP FENCE (Fig. G)
1. Lift upward on the rip fence handle (1) so that the
holding clamp (2) is fully extended.
2. Place the rip fence on the saw table and engage the
holding clamp (2) to the table rear. Lower the front
end onto the front rail (3).
3. Push down on the fence handle (1) to lock.

Fig. G
2

WARNING
To avoid possible injury and damage to the workpiece be
sure to install the blade with the teeth pointing toward the
front of table in the direction of the rotation arrow on the
blade guard.

Fig. I

INSTALLING AND CHANGING THE BLADE (Fig. H, I, J)

WARNING
To avoid injury from an accidental start, make sure the
switch is in the OFF position and the plug is not
connected to the power source outlet.
To avoid serious injury, table insert must be level with
the table. If the table insert is not level with the table,
adjust the screw (3) until it is level with the table. To
raise the insert, turn the screw counterclockwise, to
lower the insert, turn the screw clockwise.
1. Remove the table insert (1) by unscrewing the two
screws (2, 3). Be careful not to lose the rubber washer
that is on the back screw (3) beneath the table insert.
(Fig. H)

7. To tighten the arbor nut (5) place the open-end
wrench jaws on the flats of the saw arbor to keep the
arbor from turning. (Fig. J)
8. Place the box-end wrench (8) on the arbor nut (5), and
turn clockwise (to the rear of the saw table).
9. Replace the blade insert in the table recess, insert the
screws through the front and rear holes and tighten.

Fig. J

Fig. H

8
7

1
3

WARNING

Raise the blade arbor (4) (Fig. G) to the maximum
height by turning the blade raising handwheel
counterclockwise.

To avoid injury from a thrown workpiece, blade parts, or
blade contact, never operate saw without the proper insert
in place. Use the saw blade insert when sawing. Use the
dado head insert when using a dado.

— 12 —

BLADE GUARD ASSEMBLY (Fig. K, L, M)
1. Set the blade to maximum height and the tilt to zero
degrees on the bevel scale with the hand wheels. Lock
the blade lock knob.
2. Place the external toothed lock washer (1), a steel flat
washer (2) and a spring washer (10) onto the long hex
head bolt (3). Insert the bolt into the splitter bracket (4)
as shown. (Fig. K)

WARNING
Improper splitter alignment can cause "kickback" and
serious injury.

Fig. M
8

Fig. K

Kickback pawl

11
1
3.
4.

2 10

Place the oval washer (5) on the pivot rod (6). (Fig. L)
Install the bracket assembly (4) at the rear of the saw
table and s nugly - do not tighten. Thread the bolt (3)
into the internally threaded pivot rod.
NOTE: The splitter is removed from the illustration for
clarity.

Fig. L

5.
6.
7.

8.
9.

10.

INSTALLING TABLE SIDE EXTENSIONS (Fig. N)
1. Identify the right hand table extension.
NOTES:
For illustration purposes the view in Fig. N looks
"through" the saw table to the under side of the table.
The right hand table extension is the one with the
measuring scale (1) visible from the front of the saw
when it is installed to the right hand side of the saw
table (Fig. N).
2. Open both front and rear cam locking levers (2) on the
right hand side of the saw base by pulling them out
from the cam locking assemblies (4).
3. Insert the table extension mounting tubes (3) into the
two matching holes in the cam lever assemblies.
NOTE: Make sure the front mounting tube has the
measuring scale visible from the front of the saw.
4. Slide the table extension toward the table until it rests
against the saw table.
5. Lock both cam locking levers by pushing them in
toward the cam locking lever assemblies.

Fig. N

Position the blade guard arm (7) to the rear of the
table.
Using a straight edge, check to see if the blade guard
splitter (8) is aligned with the saw blade (9).
If straightening adjustment is necessary, loosen the
bolt (3) and shift the splitter assembly to right or left,
or rotate.
When the splitter is properly aligned with the saw
blade, tighten the bolt tightly.
If height adjustment is necessary, loosen the bolts (11)
and raise the splitter assembly to the desired height
and tighten the bolts. (Fig. K)
NOTE: The splitter must always be correctly aligned
so that the cut workpiece will pass on either side
without binding or twisting to the side.

— 13 —

3
4
2

INSTALLING TABLE SIDE EXTENSIONS- cont'd (Fig. O)
6. Snap one short location seat (5) over the end of the
rear table extension tube (3). Make sure the locating
pin (6) in the location seat fits into the matching hole
in the extension tube (Fig. O).
NOTES: Install location seat on front table extension
tube.
NOTE:
For illustration purposes the view in Fig. O looks
"through" the saw table to the under side of the table.

Fig. O
5

INSTALLING REAR TABLE EXTENSION (Fig. P)
1. Place the rear table extension onto the two rear table
extension tubes (1).
2. Snap two long location seats (4) over the two rear
table extension tubes (1). Make sure the locating pin in
the location seat fits into the matching hole (5) in the
extension tube.
3. Insert rear table extension tubes (1) into the two holes
in the rear of the saw table (3) and into extension tube
brackets under the table.
4. Position rear table support so instruction labels are up.
5. Snap one short location seat (4) over the end of the
left rear table extension tube (1). Make sure the
locating pin in the location seat fits into the matching
hole in the extension tube.

Fig. P

ADJUSTING REAR TABLE EXTENSION
1. Rear table extension should be positioned as close as
possible to the rear of the table when ripping short
work pieces.
2. Rear table extension should be pulled out fully until
the location seat prevents it from moving outward
when ripping long work pieces that require extra
support as you are completing the cut.
RIP FENCE ADJUSTMENT (Fig. Q)
1. The fence (1) is moved by lifting up on the handle (2)
and sliding the fence to the desired location. Pushing
down on the handle locks the fence in position.
2. Position the fence on the right side of the table, and
along one edge of the miter gauge grooves.
3. Lock the fence handle. The fence should be parallel
with the miter gauge groove.
4. If adjustment is needed to make the fence parallel to
the groove, do the following:
Loosen the two screws (3) and lift up on the
handle (2).
Hold the fence bracket (4) firmly against the front
of the saw table. Move the far end of the fence
until it is parallel with the miter gauge groove.
Tighten both screws and push the handle to lock.
5. If fence is loose when the handle is in the locked
(downward) position, do the following:
Move the handle (2) upward and turn the
adjusting nut (5) clockwise until the rear clamp is
snug. Do not turn the adjusting screw more than
1/4 turn at a time.
Over-tightening the adjusting screw will cause the
fence to come out of alignment.

WARNING
Failure to properly align fence can cause "kickback" and
serious injury.

Fig. Q
1
3

4
5

D O WN

— 14 —

RIP FENCE INDICATOR ADJUSTMENT (Fig. Q)
1. The rip fence indicator (6) points to the measurement
scale (8). The scale shows the distance from the side
of the fence to nearest side of the blade.
2. Measure the actual distance with a rule. If there is a
difference between the measurement and the
indicator, adjust the indicator (6).
3. Loosen the screw (7) and slide the indicator to the
correct measurement on the scale. Tighten the screw
and remeasure with the rule.

Fig. Q-2
90°

45°

3
1

WARNING
To avoid injury from an accidental start, make sure the
switch is in the OFF position and the plug is not connected
to the power source outlet.
ADJUSTING THE 90° AND 45° POSITIVE STOPS
(Fig. Q-1, Q-2, Q-3)
Your saw has positive stops that will quickly position the
saw blade at 90° to the table. Make adjustments only if
necessary.
90° Stop
1. Disconnect the saw from the power source.
2. Turn the blade elevation handwheel and raise the
blade to the maximum elevation.
3. Loosen the blade bevel lock handle (2) and move the
blade to the maximum vertical position. Tighten the
lock handle (2).
4. Place a combination square on the table and against
the blade (1) to determine if the blade is 90° to the
table. (Fig. Q-2)
5. If the blade is not 90° to the table, loosen the two set
screws (4), located on the bottom of the table saw,
(Fig. Q-3) with the hex key, and back off the collar.
6. Loosen the bevel lock knob. Turn the blade tilting
handwheel to move the blade until it is 90° to the
table.
7. Adjust the collar (5) so it contacts the bracket (3) when
the blade is 90° to the table. Tighten the two set
screws (4).

45° Stop
1. With the blade in the upright 90° position, loosen the
bevel lock knob and move the blade to the 45°
position as far as it will go.
2. Place the combination square on the table as shown in
(Fig. Q-2) to check if the blade is 45° to the table.
3. If the blade is not 45° to the table, adjust the screw (4)
(Fig. Q-3) with a screw driver until the blade is 45° to
the table.
4. Tighten the bevel lock handle.
5. Tighten the screw (4) until resistance is felt. Do not
overtighten.
BLADE TILT POINTER
1. When the blade is positioned at 90°, adjust the blade
tilt pointer to read 0° on the scale.
2. Loosen the holding screw, position pointer over 0°
and tighten the screw.
NOTE: Make a trial cut on scrap wood before making
critical cuts. Measure for exactness.

Fig. Q-3

4
5
3

Fig. Q-1
3 4 5

— 15 —

BLADE PARALLEL TO THE MITER GAUGE GROOVE
(Fig. R, S)

WARNING
This adjustment was made at the factory, but it should be
rechecked and adjusted if necessary.

WARNING
To prevent personal injury:
䢇 Always disconnect plug from the power source when
making any adjustments.
䢇 This adjustment must be correct or kickback could
result in a serious injury and accurate cuts can not be
made.
1.
2.
3.
4
5.
6.

7.
8.
9.

Remove the yellow switch key and unplug the saw.
Move the blade guard out of the way.
Raise the blade to the highest position and set at the
0° angle (90° straight up).
Select and mark, with a felt tip marker, a blade tooth
having a “right set”.
Place the combination square base (1) into the right
side miter gauge groove (2). (Fig. R)
Adjust the rule so it touches the front marked tooth
and lock ruler so it holds its position in the square
assembly.
Rotate the blade bringing the marked tooth to the rear
and about 1/2 inch above the blade.
Carefully slide the combination square to the rear until
the ruler touches the marked tooth.
If the ruler touches the marked tooth at the front and
rear position, no adjustment is needed at this time. If
not, perform adjustment procedure described in next
section.

Additional blade adjustments (Fig. S)
The adjusting mechanism is located on top of blade height
adjusting hand wheel under the tabletop. If the front and
rear measurements are not the same, adjust the
alignment by the mechanism as follows:
If the blade is partial to right side:
1. Loosen the two nuts (1) and the right side screw, then
adjust the left side screw.
2. Tighten the nuts (1) and the right screw and
remeasure, as described in steps 4 to 9 in the prior
section.
If the blade is partial to left side:
3. Loosen the two nuts (1) and the left side screw, then
adjust the right screw.
4. Tighten the nuts (1) and the left screw and remeasure,
as described in steps 4 to 9 in the prior section.
5. Recheck blade clearance making sure that the blade
does not hit the table insert or other parts when at the
90° and 45° settings.

Fig. S

Fig. R

— 16 —

OPERATION
OVERLOAD PROTECTION (Fig. U)
This saw has an overload relay button (3) that resets the
motor after it shuts off due to overloading or low voltage.
If the motor stops during operation, turn the ON / OFF
switch to the OFF position. Wait about five minutes for the
motor to cool. Push in on the reset button (3) and turn the
switch to the ON position.

BASIC SAW OPERATIONS
RAISE THE BLADE (Fig. T)
To raise or lower the blade, turn the blade elevation
handwheel (1) to the desired blade height, and then
tighten lock handle (2) to maintain the desired blade
angle.

Fig. T

WARNING
To avoid injury, the ON / OFF switch should be in the OFF
position and the plug removed from the power source
while the cool down takes place, to prevent accidental
starting when the reset button is pushed. Overheating
may be caused by misaligned parts or a dull blade.
Inspect your saw for proper setup before using it again.

TILTING THE BLADE (Fig. T)
1. To tilt the saw blade for bevel cutting, loosen the lock
knob (2) and turn the tilting handwheel (3).
2. Tighten the lock knobs (2) to secure.
ON/OFF SWITCH (Fig. U)
The ON / OFF switch has a removal key. With the key
removed from the switch, unauthorized and hazardous
use by children and others is minimized.

Fig. V

1. To turn the saw ON, insert key (1) into the slot in the
switch (2). Move the switch upward to the ON
position.
2. To turn the saw OFF, move the switch downward.
3. To lock the switch in the OFF position, grasp the end
(or yellow part) of the switch toggle (1), and pull it out.
4. With the switch key removed, the switch will not
operate.
5. If the switch key is removed while the saw is running,
it can be turned OFF but cannot be restarted without
inserting the switch key (1).

Fig. U

USING THE TABLE EXTENSION (Fig. V, V-1)
If the table extension is not parallel with the table.
Remove the bolts (1) and position the parallel washers (2)
between the table extension and tube until it is parallel
with the table, then tighten the bolts.
NOTE: Parallel washer (2) see page 7 for table of loose
parts ITEM: Q.

1
NOTE : Move and lock the fence to the 15" left or right side
scale. The fence is now clear of the table.
1.
2.

3
3.

Release the extension lock handles.
Slide the extension out until the correct measurement
is displayed on the tube scale. The user sights the
scale off the edge of the table.
Tighten all extension lock handles.

Fig. V-1

D O WN

Right side scale of table extension

— 17 —

CUTTING OPERATIONS
There are two basic types of cuts: ripping and
crosscutting. Ripping is cutting along the length and the
grain of the workpiece. Crosscutting is cutting either
across the width or across the grain of the workpiece.
Neither ripping nor crosscutting may be done safely
freehand. Ripping requires the use of the rip fence, and
crosscutting requires the miter gauge.

Fig. W

WARNING
Before using the saw each and every time, check the
following:

1
U P

1. Blade is tight on the arbor.
2. Bevel angle lock knob is tight.
3. If ripping, fence knob is tight and fence is parallel to
the miter gauge grooves.
4. Blade guard is in place and working properly.
5. Safety glasses are being worn.

NOTE: When width or rop is 2" to 6" wide use the push
stick to feed the work. When width of rop is narrower than
2" the push stick cannot be used because the guard will
interfere... Use the auxiliary fence as page 20.

The failure to adhere to these common safety rules, and
those printed in the front of this manual, can greatly
increase the likelihood of injury.

RIPPING (Fig. W, X)

WARNING

To prevent serious injury:
Never use the miter gauge when ripping.
Never use more than one rip fence during a single cut.
Do not allow familiarity or frequent use of your table
saw to cause careless mistakes. Remember that even
a careless fraction of a second is enough to cause a
severe injury.
Keep both hands away from the blade and path of the
blade.
The workpiece must have a straight edge against the
fence and must not be warped, twisted, or bowed.

Keep your thumbs off the table top. When both of
your thumbs touch the front edge of the table (2),
finish the cut with a push stick. Make a push stick
using the pattern on page 23.
The push stick (3) should always be used when the
ripped workpiece is 2" to 6" wide. (Fig. X)
Continue pushing the workpiece with the push stick
(3) until it passes the blade guard and clears the rear
of the table.
Never pull the piece back when the blade is turning.
Turn the switch OFF. When the blade completely stops
raise the anti-kickback pawls on each side of the
splitter and slide the workpiece out.

Fig. X

1. Remove the miter gauge. Secure the rip fence to the
table.
2. Raise the blade so it is about 1/8" higher than the top
of the workpiece.
3. Place the workpiece flat on the table and against the
fence. Keep the workpiece about 1" away from the
blade.
4. Turn the saw ON and wait for the blade to come up to
speed.
5. Slowly feed the workpiece into the blade by pushing
forward only on the workpiece section (1) that will
pass between the blade and the fence. (Fig. W)

WARNING
AVOID KICKBACK by pushing forward on the section of
the workpiece that passes between the blade and the
fence.

— 18 —

2
UP

BEVEL RIPPING
This cut is the same as ripping except the blade bevel
angle is set to an angle other than "0".

Fig. Y
3

WARNING

Cut only with the workpiece and the fence on the right
side of the blade.
RIPPING SMALL PIECES

WARNING
Avoid injury from the blade contact. Never make through
saw cuts narrower than 1/2" wide.

Fig. Y-1

1. It is unsafe to rip small pieces. Instead, rip a larger
piece to obtain the size of the desired piece.
2. When a small width is to be ripped and your hand
cannot be safely put between the blade and the rip
fence, use one or more push sticks to move the
workpiece.

CROSSCUTTING (Fig. Y)

WARNING
To prevent serious injury:
Do not allow familiarity or frequent use of your table
saw to cause careless mistakes. Remember that even
a careless fraction of a second is enough to cause a
severe injury.
Keep both hands away from the blade and the path of
the blade.
1. Remove the rip fence and place the miter gauge in the
left side groove.
2. Adjust the blade height so it is 1/8" higher than the
top of the workpiece.
3. Hold the workpiece firmly against the miter gauge
with the blade path in line with the desired cut
location. Move the workpiece to one inch distance
from the blade.
4. Start the saw and wait for the blade (1) to come up to
full speed.
5. Keep the workpiece (2) against the face of the miter
gauge (3) and flat against the face of the gauge and
flat against the table. Then slowly push the workpiece
through the blade. (Fig. Y)
6. Do not try to pull the workpiece back with the blade
turning. Turn the switch OFF, and carefully slide the
workpiece out when the blade is completely stopped.
USING WOOD FACING ON THE MITER GAUGE (Fig. Y-1)
Slots are provided in the miter gauge of attaching an
auxiliary facing (1) to make it easier to cut very long or
short pieces. Select a suitable piece of smooth wood, drill
two holes through it and attach with screws. Make sure
the facing does not interfere with the proper operation of
the sawblade guard. When cutting long workpieces, you
can make a simple support by clamping a piece of
plywood to a sawhorse.

BEVEL CROSSCUTTING (Fig. Z)
This cutting operation is the same as crosscutting except
the blade is at bevel angle other than 0 .
1. Adjust the blade (1) to the desired angle, and tighten
the blade bevel lock knob.
2. Always work to the left side of the blade. The miter
gauge (3) must be in the left side groove (2).

Fig. Z
3

2
COMPOUND MITER CROSSCUTTING (Fig. AA)
This sawing operation is combining a miter angle with a
bevel angle.
1. Set the miter gauge (3) to the desired angle. Use only
the left side groove (2).
2. Set the blade (1) bevel to the desired angle.
3. Carefully push the miter gauge to begin the cutting
operation.

Fig. AA

— 19 —

MITERING (Fig. BB)
This sawing operation is the same as crosscutting except
the miter gauge is locked at an angle other than 90
1. Hold the workpiece (2) firmly against the miter
gauge (3).
2. Feed the workpiece slowly into the blade (1) to
prevent the workpiece from moving.

Fig. CC-1
30"

1 -1 /4

3/4" Thick plywood base

5-1/2"

3-1/2"

2-5/8"
4 -3

/4 "

27"

Fig. BB

3/4" Thick plywood side

2-3/8"

Attach auxiliary fence to rip fence with two "C" clamps.
(Fig. CC-2)

Fig. CC-2

USING WOOD FACING ON THE RIP FENCE (Fig. CC)
When performing some special cutting operations, add a
wood facing (1) to either side of the rip fence (2).
1 . Use a smooth straight 3/4" thick wood board (1) that is
as long as the rip fence.
2. Attach the wood facing to the fence with wood screw
(3) through the hole in the fence. A wood fence should
be used when ripping material such as thin paneling
to prevent the material from catching between the
bottom of the fence and the table.

Fig. CC
3

AUXILIARY FENCE (Fig. CC-1)
Making the base:
Start with a piece of 3/8" plywood at least 5-1/2" wide
or wider and 30" long or longer.
Cut the piece to shape and size shown:
Making the side:
Start with a piece of 3/4" plywood at least 2-3/8" wide
or wider and 27" long or longer.
Cut the piece to shape and size shown:
Putting it together:
Put the pieces together, as shown:

WARNING
Make sure the screw heads do not stick out from the
bottom of the base, they must be flush or recessed.
The bottom must be flat and smooth enough to rest on
the saw table without rocking.

— 20 —

MAINTENANCE
MAINTAINING YOUR TABLE SAW

Fig. EE

GENERAL MAINTENANCE

WARNING
For your own safety, turn the switch OFF and remove the
switch key. Remove the plug from the power source outlet
before maintaining or lubricating your saw.

3
2

1. Clean out all sawdust that has accumulated inside the
saw cabinet and the motor.
2. Polish the saw table with an automotive wax to keep it
clean and to make it easier to slide the workpiece.
3. Clean cutting blades with pitch and gum remover.
4. A worn, cut, or damaged power cord should be
replaced immediately.

WARNING

Place a small amount of dry lubricant on bevel gear (2).
Screw rod (1) must be kept clean and free of sawdust,
gum, pitch, and other contaminants for smooth operation.

All electrical or mechanical repairs should be attempted
only by a trained repair technician. Contact Hitachi
Authorized Service Center for service. Use only identical
replacement parts. Any other parts may create a hazard.

If excessive looseness is observed in any parts of the
blade raising mechanism or tilting mechanism, take the
complete unit to Hitachi Authorized Service Center.

5. Use liquid dish washing detergent and water to clean
all plastic parts.
NOTE: Certain cleaning chemicals can damage plastic
parts.
6.

1
5

Avoid use of the following cleaning chemicals or
solvents, ammonia and household detergents
containing ammonia.

LUBRICATION
All motor bearings are permanently lubricated at the
factory and require no additional lubrication.
On all mechanical parts of your table saw where a pivot or
threaded rod are present, lubricate using graphite or
silicone. These dry lubricants will not hold sawdust as
would oil or grease.

BLADE RAISING AND TILTING MECHANISM (Fig. EE)
After each five hours of operation, the blade raising
mechanism and tilting mechanism should be checked for
looseness, binding, or other abnormalities. With the saw
dis-connected from the power source, turn the saw upside
down and alternately pull upward and downward on the
motor unit. Observe any movement of the motor
mounting mechanism. Looseness or play in the blade
raising screw (1) should be adjusted as follows:
1. Using a wrench, loosen nut (2).
2. Adjust nut (3) until it is finger-tight against the bracket
(4), then back off the nut (3) 1/6 turn.
3. Tighten nut (2) with the wrench, while holding nut (3)
in place. Maximum allowable play of screw rod (1) is
0.16" (4 mm).

— 21 —

TROUBLESHOOTING GUIDE
WARNING
To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power source before
making any adjustments.
䢇 Consult Hitachi Authorized Service Center if for any reason the motor will not run.

SYMPTOM

POSSIBLE CAUSES

CORRECTIVE ACTION

Saw will not start

1. Saw not plugged in
2. Fuse blown or circuit breaker tripped
3. Cord damaged

Does not make accurate
45° and 90° rip cuts

1. Positive stop not adjusted correctly

1. Plug in saw
2. Replace fuse or reset circuit breaker
3. Have cord replaced by Hitachi Authorized
Service Center
1. Check blade with square and adjust
positive stop
2. Check blade with square and adjust to
zero
1. Check and adjust rip fence
2. Select another piece of wood

2. Tilt angle pointer not set accurately
Material pinched blade
when ripping
Material binds on splitter

Saw makes
unsatisfactory cuts

1. Rip fence not aligned with blade
2. Warped wood, edge against fence is not
straight
1. Splitter not aligned correctly with blade

1. Dull blade
2. Blade mounted backwards
3. Gum or pitch on blade

1. Check and align splitter with blade

1. Replace blade
2. Turn the blade around
3. Remove blade and clean with turpentine
and coarse steel wool
4. Change the blade
5. Clean table with turpentine and steel wool

Blade does not raise or
tilt freely

4. Incorrect blade for work being done
5. Gum or pitch on blade causing erratic
feed
1. Rip fence out of adjustment
2. Splitter not aligned with blade
3. Feeding stock without rip fence
4. Splitter not in place
5. Dull blade
6. The operator letting go of material before
it is past saw blade
7. Miter angle lock knob is not tight
1. Sawdust and dirt in raising and tilting
mechanisms

Blade does not come up
to speed

1. Extension cord too light or too long
2. Low house voltage

1. Replace with adequate size cord
2. Contact your electric company

Machine vibrates
excessively

1. Saw not mounted securely to workbench
2. Bench on uneven floor
3. Damaged saw blade

1. Tighten all mounting hardware
2. Reposition on flat level surface Fasten to
floor if necessary
3. Replace blade

1. Miter gauge out of adjustment

1. Adjust miter gauge

Material kicked back
from blade

Does not make accurate
45° and 90° cross cuts

— 22 —

1. Align rip fence with miter gauge slot
2. Align splitter with blade
3. Install and use rip fence
4. Install and use splitter (with guard)
5. Replace blade
6. Push material all the way past saw blade
before releasing work
7. Tighten knob
1. Brush or blow out loose dust and dirt

— 23 —

1/2” Squares.

Cut off here to
push 1/2” wood.

Cut off here to
push 1/4” wood.

Notch to help
prevent hand
from slipping.

PUSH STICK

Optional
hanging hole.

Make from 1/2” or 3/4”
wood or thickness
less than width of
material to be cut.

CAUTION!
Use only good
strong wood
or plywood.
Use a jigsaw or
bandsaw to
cut out.

PARTS LIST
10" JOB SITE TABLE SAW

MODEL NO. C10FR

Always order by I.D. Number

PARTS LIST FOR SCHEMATIC A
I.D. Description
Size
2178 E X T E N T ION W IN G
(R IG HT )
2771 AN G LE R OD
08VH CLAM P-COR D
09J K W R E N CH HE X .
0B 22 HE IG HT R E G U LAT IN G
B OLT
0B 23 S ADDLE
0B 24 S PR IN G
0B 27 POIN T E R B R ACK E T
0B 2B N E E DLE POIN T E R
0B 2E S W IT CH B OX
0B 3H IN S E R T
0B 3R W R E N CH
0B 84 W AS HE R
0B 97 M OT OR B R ACK E T
0B 99 S PACE R
0B 9C PLU N G E R HOU S IN G
0B 9P CLAM P
0B 9S B R ACK E T
0B 9W B R ACK E T
0B A4 S PACE R
0B A9 S PACE R
0B AA CLAM P
0B AB S HIM
0B AC S E T N U T
0B AE AR B OR COLLAR
0B AT N U T
0B AU S U PPOR T IN G PLAT E
0B AX S T IFFE N E R
0B AY S CR E W B AR
0B AZ B E AR IN G S E AT
0B B 1 S HAFT
0B B 2 PAR R LE R IN G
0B C2 LOCAT ION S E AT

Qty
1

0G D0 B LADE
0J 3U W R E N CH HE X .
0J 4F FLAT W AS HE R
0J 4H FLAT W AS HE R
0J 5L FLAT W AS HE R
0J 6T FLAT W AS HE R
0J 6U FLAT W AS HE R
0J 6V FLAT W AS HE R
0J 70 FLAT W AS HE R
0J 76 FLAT W AS HE R
0J 76 FLAT W AS HE R
0J 80 FLAT W AS HE R

1
1
1
2
10
4
1
8
1
1
1
2

?8* 16-2.5
?10* 30-0.2
?5* 10-0.3
3/16* 3/4-1/16
3/16* 1/2-3/64
3/16* 3/8-0.022
1/4* 3/4-7/64
1/4* 3/4-1/16
1/4* 3/4-1/16
5/32* 13/32-3/64

1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2

I.D.
0J 8D
0J 8D
0J 95
0J AA
0J AE
0J AF
0J C9
0J CA
0J CA
0J CR
0J E D
0J E Y
0J PB
0J X 7
0J X L
0K 0Z
0K 16
0K 25
0K 3G
0K 57
0K 7K
0K 8C
0K 8D
0K 9T
0K 9U
0K 9U
0K A4
0K AP
0K C8
0K CA
0K CH
0K CX
0K CY
0K DR
0K DU
0K F6
0K FG
0K HZ
0K J 4
0K J 5
0K M R
0K M S
0K M V
0K M W
0K M Y
0K N D
0K QJ
0K QW

Description
Size
Qty
FLAT W AS HE R
3/8* 3/4-5/64 1
FLAT W AS HE R
3/8* 3/4-5/64 1
S PR IN G W AS HE R
1
W AS HE R
1
E X T E R N AL T OOT H LOCK W AS HE R
2
E X T E R N AL T OOT H LOCK W AS HE R
1
S PR IN G PIN
1
S PR IN G PIN
1
S PR IN G PIN
1
S PR IN G PIN
1
C-R IN G
A-16
1
E -R IN G
E -9
1
HE X . HD. B OLT
M 5* 0.8-20 2
HE X . S OC. S E T S CR E W
M 6* 1.0-6 2
HE X . S OC. S E T S CR E W
M 10* 1.5-12 1
HEX . HD. S CREW AND W AS HER M 8* 1.25-16 4
HEX . HD. S CREW AND W AS HER M 8* 1.25-16 1
HEX .S OCKET HD.CAP S CREW S M 5* 0.8-20 1
CR.RE. PAN HD. S CREW & W AS HER M 5* 0.8-12 1
CR .R E .COU N T HD. S CR E W M 5* 0.8-16 1
CR. RE. ROUND WAS HER HD. S CREW M 6* 1.0-12 2
CR. RE.COUNT HD. TAPPING S CREW M 4* 18-10 4
CR. RE.COUNT HD. TAPPING S CREW M 4* 18-16 2
HE X . HD. TAPPIN G S CR E W M 5* 16-16 6
HE X . HD. TAPPIN G S CR E W M 5* 16-25 4
HE X . HD. TAPPIN G S CR E W M 5* 16-25 4
CR.RE. PAN HD. TAPPING S CREW M 4* 16-16 2
CR.RE. PAN HD. TAPPING S CREW M 5* 0.8-10 1
CR. RE. TRUS S HD. TAPPING S CREW M 4* 16-16 2
CR. RE. TRUS S HD. TAPPING S CREW M 5* 12-12 2
CR.RE. PAN HEAD TAPPING & WASHER SCREW M 5* 0.8-12 2
CROS S -RECES S ED PAN HD PLAIN M 5* 0.8-10 6
W AS HER TAPPING S CREW
CR. RE. PAN HD PLAIN W AS HER M 5* 0.8-12 4
TAPPING S CR EW
CR . R E . PAN HD. S CR E W M 5* 0.8-10 1
CR . R E . PAN HD. S CR E W M 6* 1.0-12 2
CR . R E . PAN HD. S CR E W M 4* 0.7-8 2
CR . R E . PAN HD. S CR E W M 5* 0.8-12 2
CAP HD. S Q.N E CK B OLT M 6* 1.0-12 2
CAP HD. S Q.N E CK B OLT M 6* 1.0-35 1
CAP HD. S Q.N E CK B OLT M 6* 1.0-80 1
HE X . N U T
M 5* 0.8 T=4 1
HE X . N U T
M 6* 1.0 T=5 1
HE X . N U T
M 10* 1.5 T=8 1
HE X . N U T
M 10* 1.5 T=4 1
HE X . N U T
M8* 1.25T=6.5 1
HE X . N U T
M 5* 0.8 T=4 2
CR OW N N U T
M 8* 1.25
2
T =12.5
N U T CHU CK
M 5* 0.8 T=5 1

— 24 —

I.D.
0K QW
0K R X
0K R X
0K S W
0K W Z
0LM G
0LS L
0T 00
10G N
10G P
20W Q
216F
237U
238S
275D
275E
275F
275R
275U
27QV
287H
28CK
28FK
28K X
28L9
28M C
28M D
28M G
28M H
28N 2

Description
Size
Qty
N U T CHE CK
M 5* 0.8 T=5 1
HEXAGON NUT AND FLAT WAS HER M 6* 1.0
2
HEXAGON NUT AND FLAT WAS HER M 6* 1.0
1
S T R AIN R E LIE F
1
LE AD W IR E AS S 'Y
1
LOCK IN G CAB LE T IE
1
CIR CU IT B R E AK E R S W IT CH
1
S LIDIN G B AS E AS S 'Y
2
U PE R T U B E
1
U PE R T U B E
1
M 6* 1.0-50 1
HE X . HD. B OLT
S W IT CH K E Y
1
COVE R
1
POIN T E R
1
E X T E N T ION W IN G
1
U PE R T U B E
2
LOCAT ION S E AT
2
LOCAT ION S E AT
1
S PACE R
1
PAR T S B OX CAR T ON
1
R E T AIN IN G CLIP
1
POW E R CAB LE AS S 'Y
1
T AB LE
1
B ODY S HE LL
1
LOCK K N OB
1
PAR ALLE L B R ACK E T AS S 'Y
1
M IT E R G AU G E AS S 'Y
1
HAN D W HE E L AS S 'Y
1
HAN D W HE E L AS S 'Y
1
B AT T E R Y AS S E M B LY
1

28P2
28PA
28W 3
28W 4
28W 6
28W 7
28W 8
28W 9
28W A
28W B
28W C
28W D
28W E
28W F
28W G
28W L
28X 4
290T

R OCK E R S W IT CH
K N OB
LAB E L
S T ICK E R
S T ICK E R
CAU T ION LAB E L
LAB E L
S CALE
CAU T ION LAB E L
W AR N IN G LAB E L
W AR N IN G LAB E L
CAU T ION LAB E L
S CALE
S CALE
W AR N IN G LAB E L
W AR N IN G LAB E L
B LADE G U AR D AS S 'Y
M OT OR

1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

10" JOB SITE TABLE SAW

MODEL NO. C10FR

— 25 —

10" JOB SITE TABLE SAW

I.D.
01AD
01AE
0J4E
0J4F
0JAZ
0K7D
0K7M
0KDJ
0KDR
0KKU
0KMS
0KQ4
0KQW
0KQW
0KQX
0KQY
0KQY
213T
22FZ

Description
WING NUT
LEVELING PAD
FLAT WASHER
FLAT WASHER
WAVE WASHER
CR. RE. ROUND WASHER HD. SCREW
CR. RE. ROUND WASHER HD. SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. SCREW
CR.RE. PAN HD. ROUND NECK SCREW
HEX. NUT
WING NUT
NUT CHUCK
NUT CHUCK
NUT CHUCK
NUT CHUCK
NUT CHUCK
ROLLING WHEEL
CAP HD. SQ.NECK BOLT

MODEL NO. C10FR

Size

Qty
1
1
ø6*13-1
4
ø8X16-2.5
4
WW-6
2
M6*1.0-10
2
M6*1.0-18
1
M5*0.8-12
2
M5*0.8-10
4
M5*08-10
1
M6*1.0 T=5
1
M8*1.25
1
M5*0.8 T=5
6
M5*0.8 T=5
1
M6*1.0 T=6
4
M8*1.25 T=8 4
M8*1.25 T=8 2
2
M8*1.25-45
2

I.D.
27DJ
27DL
27DM
27DV
27DW
27DY
27DZ
27E6
27RQ
27RR
288R
28BU
28BX
28L2
28L3
28VU
28VV
28VX
28VZ

— 26 —

Description
FOAM
HANDLE
BRACKET ASS'Y (RIGHT)
LEVELING PAD
DUST COLLECTOR ASS'Y
COUPLING
BRACKET ASS'Y (LEFT)
HOOK
CAP HD. SQ.NECK BOLT
CR.-RE. TRUSS HD. SCREW
HEX. HD. BOLT
FLOOR PLATE
CROSS-RECESSED PAN HD PLAIN WASHER TAPPING SCREW
CLAMP HANDLE
FOLLOWER PLATE
HOOK
CONNECTOR
SUPPORTING TUBE ASS'Y
LEVELING PAD

Size

M8*1.25-40
M6*1.0-45
M8*1.25-55
M5*0.8-10

Qty
1
1
1
3
1
1
1
1
4
4
4
1
4
4
1
2
1
1
1

— 27 —

Issued by

Hitachi Koki Co., Ltd.
Sinagawa Intercity Tower A, 15-1, Konan 2-chome,
Minato-ku, Tokyo 108-6020, Japan
Distributed by

Hitachi Koki U.S.A., Ltd.
3950 Steve Reynolds Blvd.
Norcross, GA 30093

Hitachi Koki Canada Co.
6395 Kestrel Road
Mississauga ON L5T 1Z5

407
Code No. C99135061
Printed in Taiwan

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2004:06:29 15:34:10Z
Modify Date                     : 2004:08:20 19:21:15+08:00
Page Count                      : 28
Page Layout                     : SinglePage
Creation Date                   : 2004:06:29 15:34:10Z
Producer                        : Acrobat Distiller 4.0.5  for Macintosh
Author                          : NAVIX 2004.
Mod Date                        : 2004:08:20 19:21:15+08:00
Metadata Date                   : 2004:08:20 19:21:15+08:00
Creator                         : NAVIX 2004.
Title                           : C10FR_US_EnglishOnly_PRESS  2004.06.30

EXIF Metadata provided by EXIF.tools

Hitachi Saw C 10Fr Users Manual C10FR_US_EnglishOnly_PRESS 2004.06.30

Hitachi Saw C 10FR C10FR_OM_6728

C 10FR to the manual 5181ca69-07a5-4ad5-bf78-60accad1a96a

Navigation menu

Versions of this User Manual:

Views

Navigation