Honeywell 025010 PC-502.2 User Manual PC 502 2 v1 0 DS

INNCOM International Inc. PC-502.2 PC 502 2 v1 0 DS

Users Manual

INNCOMȱPCȬ502.2ȱDatasheetȱOverviewȱThe INNCOM PC-502.2 wall mounted module can be used to expand the range of a Layer-2 RF network or provide the protocol gateway from INNCOM S5-bus to Layer-2 RF protocol.In the Layer-2.2 802.15.4 Zigbee 2006 mesh network, the PC-502.2 is designed to patch areas within the network where signal strength is lost due to distance limitations or interference. It also serves to create multiple pathways, increasing the redundancy of the mesh communications to ensure maximum network reliability. FeaturesȱxSmall wall mountable form factor x2.4Ghz IEEE 802.15.4 compliant RF transceiver (CC2430 radio core)xMedium and long range variants available xIndustrial temperature ratings 0-65 degrees C xFCC Part 15b listed SpecificationȱParameterȱPCȬ502.2ȱRF Data Rate 250kbpsAntenna Type SMTIndoor Range 100ftOutdoor/ RF line-of-sight range 1000ft+Transmit Power 10mW (+18dBm) Receive Sensitivity -94.6dBm Frequency Band 2.405-2.475GHzEncryption AES-128 Protocol 802.15.4 Frequency Channels 15Input Voltage 12VDCCurrent Consumption 100mA (Peak) Operating Ambient Temperature 40 ° C LED /Switch Reset indication, blinks when unit is connected to an RF network. Rapid blink during binding association. Figure 1 PC-502.210dBm0-40℃,0-95%RH
INNCOM PC-502.2 Datasheet Page | 2Ranges are determined by performing an RF link quality test using e528.3G thermostats as the transmitter and the PC-502.2 as the receiver. The maximum distance threshold is based on a 95% overall link quality. Outdoor ranges were conducted in a low noise, free air environment. Indoor ranges are for reference. Indoor ranges are affected by the ambient environmental noise floor and building construction materials. NetworkȱTopologyȱFigure 2 PC-502 Layer-2 Topology In this application, the PC-502.2 in participation with the e529.RF provides the Layer-1 to Layer-2 RF Bridge where both wireless in-room and wireless back-end networking are required. The PC-502.2 can also patch areas within the Layer-2 network where signal strength is lost due to distance limitations or interference.
INNCOM PC-502.2 Datasheet Page | 3CommissioningȱThe PC-502.2 must be bound to the controlling device (e.g., the E529.RF in Figure 2 above) to receive configuration information. On the E529.RF in service mode xOpen the run menu and press Off/Auto xSet the value to 3 and press Display xWhen Display is pressed, the e529.RF sends Layer-2 configurations to the PC-502.2. (This function does not offer any feedback on the screen so it is recommended that the Display button be pressed 3 or 4 times to ensure configuration.) Safety/RegulatoryȱParameterȱConditionȱStatusȱFCC Part 15b 02-9994 is FCC listed. 02-9894, and 02-9927 FCC listings are pending. PCȬ502.2ȱDimensionsȱȱHeaderȱandȱConnectionsȱH3ȱ(InȱSystemȱProgramming)ȱPinȱFunctionȱTypeȱMinȱMaxȱ1-8 Programming ---H4ȱ/ȱH5ȱ(S5ȬbusȱIn/Out)ȱPinȱFunctionȱTypeȱMinȱMaxȱ1-GND Common ---2-12VDC Input voltage In 11.75 12.25
INNCOM PC-502.2 Datasheet Page | 43-S5-bus Multi-drop In/Out -H6ȱ(SystemȬ5)ȱPinȱFunctionȱTypeȱMinȱMaxȱ1-GND Common ---2-12VDC Input voltage In 11.75 12.25 3-S5-bus Multi-drop In/Out -4–InOut1 TTL In/Out -5-InOut2 TTL In/Out -3-pin to 3-pin harness for 12VDC and S5bus connection OrderingȱInformationȱPartȱNumberȱOPNȱDescriptionȱ01-5010.2 PC-502.2 PC-502 with 02-9894 20db Radio DocumentȱRevisionȱHistoryȱRevisionȱDateȱIssuedȱ ȱReasonȱ0.1 27-Mar-2009 FCC for PC-502 0.2 31-Mar-2009 Edited for content and format 1.0 07-Apr-2009 Released
Warning Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20 cm between the radiator& your body Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

Navigation menu