Honeywell 1452g Voyager 1400g/1452g Series Area Imaging Scanner User’s Guide User Manual To The Cbd2142f 9824 40b8 A8ca 27bf13d4c5af
User Manual: Honeywell 1452g to the manual
Open the PDF directly: View PDF 
.
Page Count: 206
| Download | |
| Open PDF In Browser | View PDF |
Voyager™ 1450g/1452g Series
Area-Imaging Scanner
User’s Guide
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this
document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been
made. The information in this publication does not represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages
resulting from the furnishing, performance, or use of this material. HII disclaims all responsibility for the selection and use of
software and/or hardware to achieve intended results.
This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document
may be photocopied, reproduced, or translated into another language without the prior written consent of HII.
2014 Honeywell International Inc. All rights reserved.
Web Address: www.honeywellaidc.com
Microsoft® Windows® is a trademark or registered trademark of Microsoft Corporation.
Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies
and are the property of their respective owners.
For patent information, please refer to www.hsmpats.com.
Table of Contents
Chapter 1 - Getting Started
About This Manual ...............................................................................................................1-1
Unpacking Your Device .......................................................................................................1-1
Connecting the Device .........................................................................................................1-1
Connecting with USB .....................................................................................................1-1
Connecting with Keyboard Wedge.................................................................................1-2
Connecting with RS232 Serial Port................................................................................1-3
Connecting with RS485..................................................................................................1-4
Mounting a CCB01-010BT Charge Base .............................................................................1-6
Reading Techniques ............................................................................................................1-6
Menu Bar Code Security Settings ........................................................................................1-6
Setting Custom Defaults ......................................................................................................1-7
Resetting the Custom Defaults ............................................................................................1-7
Chapter 2 - Programming the Interface
Introduction ..........................................................................................................................2-1
Programming the Interface - Plug and Play .........................................................................2-1
Keyboard Wedge .................................................................................................................2-1
Laptop Direct Connect .........................................................................................................2-1
RS232 Serial Port ................................................................................................................2-1
RS485 ..................................................................................................................................2-2
RS485 Packet Mode ......................................................................................................2-2
USB IBM SurePos ...............................................................................................................2-3
USB PC or Macintosh Keyboard..........................................................................................2-3
USB HID ..............................................................................................................................2-4
USB Serial ...........................................................................................................................2-4
CTS/RTS Emulation.......................................................................................................2-4
ACK/NAK Mode .............................................................................................................2-4
Remote MasterMind™ for USB ...........................................................................................2-5
Verifone® Ruby Terminal Default Settings...........................................................................2-5
Gilbarco® Terminal Default Settings ....................................................................................2-5
Honeywell Bioptic Aux Port Configuration ...........................................................................2-6
Datalogic™ Magellan© Bioptic Aux Port Configuration........................................................2-6
NCR Bioptic Aux Port Configuration ....................................................................................2-6
Wincor Nixdorf Terminal Default Settings ............................................................................2-6
Wincor Nixdorf Beetle™ Terminal Default Settings .............................................................2-7
Wincor Nixdorf RS232 Mode A ............................................................................................2-7
Keyboard Country Layout ....................................................................................................2-8
Keyboard Style...................................................................................................................2-15
Keyboard Conversion ........................................................................................................2-16
Control Character Output ...................................................................................................2-17
Keyboard Modifiers ............................................................................................................2-17
i
RS232 Modifiers ................................................................................................................ 2-18
RS232 Baud Rate........................................................................................................ 2-18
RS232 Word Length: Data Bits, Stop Bits, and Parity ................................................. 2-19
RS232 Receiver Time-Out........................................................................................... 2-20
RS232 Handshaking.................................................................................................... 2-20
RS232 Timeout............................................................................................................ 2-21
XON/XOFF .................................................................................................................. 2-21
ACK/NAK ..................................................................................................................... 2-22
Scanner to Bioptic Communication ................................................................................... 2-22
Scanner-Bioptic Packet Mode ..................................................................................... 2-22
Scanner-Bioptic ACK/NAK Mode................................................................................. 2-22
Scanner-Bioptic ACK/NAK Timeout............................................................................. 2-23
Chapter 3 - Cordless System Operation
How the Cordless Charge Base/Access Point Works ......................................................... 3-1
Linking the Scanner to a Charge Base................................................................................ 3-1
Linking the Scanner to an Access Point .............................................................................. 3-1
Replacing a Linked Scanner................................................................................................ 3-2
Communication Between the Cordless System
and the Host...................................................................................................................... 3-2
Programming the Scanner and Base or Access Point ........................................................ 3-3
RF (Radio Frequency) Module Operation ........................................................................... 3-3
System Conditions............................................................................................................... 3-3
Linking Process ............................................................................................................. 3-3
Scanner Is Out of Range ............................................................................................... 3-3
Scanner Is Moved Back Into Range .............................................................................. 3-3
Out of Range and Back into Range with Batch Mode On.............................................. 3-3
Page Button......................................................................................................................... 3-3
About the Battery................................................................................................................. 3-4
Charging Information ..................................................................................................... 3-4
Battery Recommendations ............................................................................................ 3-4
Proper Disposal of the Battery....................................................................................... 3-4
Beeper and LED Sequences and Meaning ......................................................................... 3-5
Scanner LED Sequences and Meaning......................................................................... 3-5
Base/Access Point LED Sequences and Meaning ........................................................ 3-5
Base Power Communication Indicator........................................................................... 3-5
Reset Scanner..................................................................................................................... 3-6
Scanning While in Base Cradle ........................................................................................... 3-6
Base Charging Modes ......................................................................................................... 3-6
Paging ................................................................................................................................. 3-7
Paging Mode.................................................................................................................. 3-7
Paging Pitch................................................................................................................... 3-7
Error Indicators .................................................................................................................... 3-8
Beeper Pitch - Base Error.............................................................................................. 3-8
Number of Beeps - Base Error ...................................................................................... 3-8
Scanner Report ................................................................................................................... 3-8
Scanner Address ................................................................................................................. 3-9
Base or Access Point Address ............................................................................................ 3-9
ii
Scanner Modes ................................................................................................................... 3-9
Charge Only Mode......................................................................................................... 3-9
Linked Modes ................................................................................................................ 3-9
Unlinking the Scanner ....................................................................................................... 3-10
Override Locked Scanner ............................................................................................ 3-10
Out-of-Range Alarm .......................................................................................................... 3-10
Alarm Sound Type ....................................................................................................... 3-11
Scanner Power Time-Out Timer........................................................................................ 3-11
Flexible Power Management ............................................................................................. 3-12
Batch Mode ....................................................................................................................... 3-13
Batch Mode Beep ........................................................................................................ 3-14
Batch Mode Storage .................................................................................................... 3-14
Batch Mode Quantity ................................................................................................... 3-15
Batch Mode Output Order............................................................................................ 3-16
Total Records .............................................................................................................. 3-17
Delete Last Code ......................................................................................................... 3-17
Clear All Codes............................................................................................................ 3-17
Transmit Records to Host ............................................................................................ 3-17
Batch Mode Transmit Delay ........................................................................................ 3-17
Multiple Scanner Operation ............................................................................................... 3-18
Scanner Name................................................................................................................... 3-18
Application Work Groups................................................................................................... 3-19
Application Work Group Selection ............................................................................... 3-20
Resetting the Factory Defaults: All Application Work Groups ........................................... 3-20
Resetting the Custom Defaults: All Application Work Groups ........................................... 3-21
Using the Scanner with Bluetooth Devices........................................................................ 3-21
Bluetooth HID Keyboard Connect................................................................................ 3-21
Virtual Keyboard .......................................................................................................... 3-22
Bluetooth HID Keyboard Disconnect ........................................................................... 3-23
Bluetooth Serial Port - PCs/Laptops ............................................................................ 3-23
PDAs/Mobility Systems Devices.................................................................................. 3-23
Changing the Scanner’s Bluetooth PIN Code.............................................................. 3-23
Minimizing Bluetooth/ISM Band Network Activity .............................................................. 3-23
Auto Reconnect Mode ................................................................................................. 3-24
Maximum Link Attempts .............................................................................................. 3-24
Relink Time-Out........................................................................................................... 3-25
Bluetooth/ISM Network Activity Examples................................................................... 3-25
Host Acknowledgment....................................................................................................... 3-26
Chapter 4 - Input/Output Settings
Power Up Beeper ................................................................................................................ 4-1
Beep on BEL Character....................................................................................................... 4-1
Trigger Click ........................................................................................................................ 4-1
iii
Good Read and Error Indicators.......................................................................................... 4-2
Beeper – Good Read..................................................................................................... 4-2
Beeper Volume – Good Read........................................................................................ 4-2
Beeper Pitch – Good Read............................................................................................ 4-2
Beeper Pitch – Error ...................................................................................................... 4-3
Beeper Duration – Good Read ...................................................................................... 4-3
LED – Good Read ......................................................................................................... 4-3
Number of Beeps – Good Read .................................................................................... 4-4
Number of Beeps – Error............................................................................................... 4-4
Good Read Delay .......................................................................................................... 4-4
User-Specified Good Read Delay.................................................................................. 4-4
Manual Trigger Mode .......................................................................................................... 4-5
LED Illumination - Manual Trigger ................................................................................. 4-5
Serial Trigger Mode ............................................................................................................. 4-5
Read Time-Out .............................................................................................................. 4-5
Presentation Mode .............................................................................................................. 4-6
Idle Illumination - Presentation Mode ............................................................................ 4-6
Presentation Sensitivity ................................................................................................. 4-6
Presentation Centering .................................................................................................. 4-6
In-Stand Sensor Mode......................................................................................................... 4-8
Poor Quality Codes ............................................................................................................. 4-8
Poor Quality 1D Codes .................................................................................................. 4-8
Poor Quality PDF Codes ............................................................................................... 4-9
CodeGate® .......................................................................................................................... 4-9
Mobile Phone Read Mode ................................................................................................... 4-9
Hands Free Time-Out.......................................................................................................... 4-9
Reread Delay..................................................................................................................... 4-10
User-Specified Reread Delay ............................................................................................ 4-10
2D Reread Delay ......................................................................................................... 4-10
Character Activation Mode ................................................................................................ 4-11
Activation Character .................................................................................................... 4-11
End Character Activation After Good Read ................................................................. 4-12
Character Activation Laser Timeout ............................................................................ 4-12
Character Deactivation Mode ............................................................................................ 4-12
Deactivation Character ................................................................................................ 4-12
Illumination Lights.............................................................................................................. 4-13
Aimer Delay ....................................................................................................................... 4-13
User-Specified Aimer Delay......................................................................................... 4-13
Aimer Mode ....................................................................................................................... 4-13
Centering ........................................................................................................................... 4-14
No Read ............................................................................................................................ 4-15
Video Reverse ................................................................................................................... 4-16
Working Orientation........................................................................................................... 4-16
iv
Chapter 5 - Data Editing
Prefix/Suffix Overview ......................................................................................................... 5-1
To Add a Prefix or Suffix:............................................................................................... 5-1
To Clear One or All Prefixes or Suffixes ........................................................................ 5-2
To Add a Carriage Return Suffix to All Symbologies ..................................................... 5-2
Prefix Selections.................................................................................................................. 5-2
Suffix Selections .................................................................................................................. 5-2
Function Code Transmit ...................................................................................................... 5-3
Intercharacter, Interfunction, and Intermessage Delays...................................................... 5-3
Intercharacter Delay ...................................................................................................... 5-3
User Specified Intercharacter Delay .............................................................................. 5-3
Interfunction Delay......................................................................................................... 5-4
Intermessage Delay....................................................................................................... 5-4
Chapter 6 - Data Formatting
Data Format Editor Introduction .......................................................................................... 6-1
Add a Data Format .............................................................................................................. 6-1
Other Programming Selections...................................................................................... 6-2
Terminal ID Table ................................................................................................................ 6-3
Data Format Editor Commands........................................................................................... 6-3
Move Commands........................................................................................................... 6-4
Search Commands ........................................................................................................ 6-5
Miscellaneous Commands............................................................................................. 6-7
Data Formatter .................................................................................................................... 6-9
Primary/Alternate Data Formats .......................................................................................... 6-9
Chapter 7 - Symbologies
All Symbologies ................................................................................................................... 7-1
Message Length Description ............................................................................................... 7-1
Codabar............................................................................................................................... 7-2
Codabar Concatenation................................................................................................. 7-3
Code 39 ............................................................................................................................... 7-4
Code 32 Pharmaceutical (PARAF) ................................................................................ 7-5
Full ASCII....................................................................................................................... 7-6
Code 39 Code Page ...................................................................................................... 7-6
Interleaved 2 of 5................................................................................................................. 7-7
NEC 2 of 5 ........................................................................................................................... 7-8
Code 93 ............................................................................................................................... 7-9
Code 93 Code Page .................................................................................................... 7-10
Straight 2 of 5 Industrial (three-bar start/stop)................................................................... 7-11
Straight 2 of 5 IATA (two-bar start/stop) ............................................................................ 7-12
Matrix 2 of 5....................................................................................................................... 7-13
Code 11 ............................................................................................................................. 7-14
Code 128 ........................................................................................................................... 7-15
ISBT 128 Concatenation.............................................................................................. 7-15
Code 128 Code Page .................................................................................................. 7-16
v
GS1-128 ............................................................................................................................ 7-17
UPC-A ............................................................................................................................... 7-17
UPC-A/EAN-13 with Extended Coupon Code ................................................................... 7-19
Coupon GS1 DataBar Output............................................................................................ 7-20
UPC-E0 ............................................................................................................................. 7-20
UPC-E1 ............................................................................................................................. 7-22
EAN/JAN-13 ...................................................................................................................... 7-23
Convert UPC-A to EAN-13 .......................................................................................... 7-23
ISBN Translate ............................................................................................................ 7-25
EAN/JAN-8 ........................................................................................................................ 7-25
MSI .................................................................................................................................... 7-27
GS1 DataBar Omnidirectional ........................................................................................... 7-29
GS1 DataBar Limited......................................................................................................... 7-29
GS1 DataBar Expanded .................................................................................................... 7-30
Codablock A ...................................................................................................................... 7-30
Codablock F ...................................................................................................................... 7-31
PDF417 ............................................................................................................................. 7-32
MacroPDF417 ................................................................................................................... 7-32
MicroPDF417..................................................................................................................... 7-33
GS1 Composite Codes...................................................................................................... 7-33
UPC/EAN Version........................................................................................................ 7-34
GS1 Emulation .................................................................................................................. 7-34
TCIF Linked Code 39 (TLC39) .......................................................................................... 7-35
QR Code............................................................................................................................ 7-35
QR Code Page ............................................................................................................ 7-36
Data Matrix ........................................................................................................................ 7-37
Data Matrix Code Page ............................................................................................... 7-37
MaxiCode .......................................................................................................................... 7-38
Aztec Code ........................................................................................................................ 7-39
Aztec Code Page......................................................................................................... 7-39
Chinese Sensible (Han Xin) Code..................................................................................... 7-40
Postal Codes - 2D ............................................................................................................. 7-41
Single 2D Postal Codes:.............................................................................................. 7-41
Combination 2D Postal Codes:.................................................................................... 7-42
Postal Codes - Linear ........................................................................................................ 7-45
China Post (Hong Kong 2 of 5).................................................................................... 7-45
Korea Post ................................................................................................................... 7-46
Chapter 8 - Interface Keys
Keyboard Function Relationships........................................................................................ 8-1
Supported Interface Keys .................................................................................................... 8-2
Chapter 9 - Utilities
To Add a Test Code I.D. Prefix to All Symbologies ............................................................. 9-1
Show Decoder Revision ...................................................................................................... 9-1
Show Scan Driver Revision ................................................................................................. 9-1
Show Software Revision...................................................................................................... 9-1
vi
Show Data Format............................................................................................................... 9-1
Test Menu............................................................................................................................ 9-2
EZConfig-Scanning Introduction.......................................................................................... 9-2
Installing EZConfig-Scanning from the Web.................................................................. 9-2
Resetting the Factory Defaults ............................................................................................ 9-3
Chapter 10 - Serial Programming Commands
Conventions....................................................................................................................... 10-1
Menu Command Syntax .................................................................................................... 10-1
Query Commands ............................................................................................................. 10-1
Responses................................................................................................................... 10-2
Trigger Commands............................................................................................................ 10-3
Resetting the Custom Defaults.......................................................................................... 10-3
Menu Commands .............................................................................................................. 10-3
Chapter 11 - Product Specifications
Voyager 1450g Scanner Product Specifications ............................................................... 11-1
Voyager 1452g Cordless Scanner Product Specifications ................................................ 11-2
CCB01-010BT Charge Base Product Specifications......................................................... 11-3
Standard Cable Pinouts..................................................................................................... 11-4
Serial Output................................................................................................................ 11-4
USB ............................................................................................................................. 11-4
RS485 Output .............................................................................................................. 11-5
Chapter 12 - Maintenance
Repairs .............................................................................................................................. 12-1
Maintenance ...................................................................................................................... 12-1
Cleaning the Device..................................................................................................... 12-1
Inspecting Cords and Connectors ............................................................................... 12-1
Replacing Cables in Corded Scanners.............................................................................. 12-1
Replacing a Corded Scanner Interface Cable ............................................................. 12-2
Replacing Cables and Batteries in Cordless Systems ...................................................... 12-2
Replacing an Interface Cable in a Base ...................................................................... 12-2
Changing a Cordless Scanner Battery ........................................................................ 12-3
Troubleshooting a Corded Scanner................................................................................... 12-3
Troubleshooting a Cordless System.................................................................................. 12-3
Troubleshooting a Base............................................................................................... 12-3
Troubleshooting a Cordless Scanner .......................................................................... 12-4
Chapter 13 - Customer Support
Technical Assistance......................................................................................................... 13-1
vii
Appendix A - Reference Charts
Symbology Charts ...............................................................................................................A-1
Linear Symbologies .......................................................................................................A-1
2D Symbologies.............................................................................................................A-2
Postal Symbologies .......................................................................................................A-2
ASCII Conversion Chart (Code Page 1252)........................................................................A-3
Lower ASCII Reference Table.............................................................................................A-4
ISO 2022/ISO 646 Character Replacements ......................................................................A-7
Unicode Key Maps ..............................................................................................................A-9
Sample Symbols
Programming Chart
viii
1
Getting Started
About This Manual
This User’s Guide provides installation and programming instructions for the Voyager™ 1450g corded area-imaging scanners
and Voyager 1452g cordless area-imaging scanners. Product specifications, dimensions, warranty, and customer support information are also included.
Note: The selections in this User’s Guide are dependent on the Voyager 145Xg model you have purchased.
PDF and 2 dimensional bar codes can only be read by model 145Xg2D and cannot be read by model 145Xg1D.
Honeywell bar code scanners are factory programmed for the most common terminal and communications settings. If you need
to change these settings, programming is accomplished by scanning the bar codes in this guide.
An asterisk (*) next to an option indicates the default setting.
Unpacking Your Device
After you open the shipping carton containing the product, take the following steps:
• Check for damage during shipment. Report damage immediately to the carrier who delivered the carton.
• Make sure the items in the carton match your order.
• Save the shipping container for later storage or shipping.
Connecting the Device
Connecting with USB
A scanner or a cordless base can be connected to the USB port of a computer.
1. Connect the appropriate interface cable to the device first, then to the computer.
Corded Voyager 1450g
USB Connection:
1-1
CCB01-010BT Base
USB Connection:
Note: The power supply must be ordered separately, if needed.
2. If you are connecting a CCB01-010BT Base, make sure the cables are secured in the wireways in the bottom of the
cordless base and the base sits flat on a horizontal surface.
3. The scanner beeps.
4. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols in the back of this
manual.
The unit defaults to a USB PC Keyboard. Refer to page 2-3 for other USB terminal settings.
For additional USB programming and technical information, refer to “USB Application Note,” available at www.honeywellaidc.com.
Connecting with Keyboard Wedge
A scanner or cordless base can be connected between the keyboard and PC as a “keyboard wedge,” where the scanner
provides data output that is similar to keyboard entries. The following is an example of a keyboard wedge connection:
1. Turn off power and disconnect the keyboard cable from the back of the terminal/computer.
2. Connect the appropriate interface cable to the device and to the terminal/computer.
Corded Voyager 1450g
Keyboard Wedge Connection:
1-2
CCB01-010BT Base
Keyboard Wedge Connection:
Note: The power supply must be ordered separately, if needed.
3. If you are connecting a CCB01-010BT Base, make sure the cables are secured in the wireways in the bottom of the
cordless base and the base sits flat on a horizontal surface.
4. Turn the terminal/computer power back on. The scanner beeps.
5. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols in the back of this
manual. The scanner beeps once.
The unit defaults to an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard. A carriage return (CR)
suffix is added to bar code data.
Connecting with RS232 Serial Port
1. Turn off power to the terminal/computer.
2. Connect the appropriate interface cable to the device.
Note: For the scanner or cordless base to work properly, you must have the correct cable for your type of terminal/computer.
1-3
Corded Voyager 1450g
RS232 Serial Port Connection:
CCB01-010BT Base
RS232 Serial Port Connection:
Note: The power supply must be ordered separately, if needed.
3. If you are connecting a CCB01-010BT Base, make sure the cables are secured in the wireways in the bottom of the
cordless base and the base sits flat on a horizontal surface.
4. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the connector to the
port.
5. Once the scanner or cordless base has been fully connected, power up the computer.
This interface programs 115,200 baud, 8 data bits, no parity, and 1 stop bit.
Connecting with RS485
A scanner or cordless base can be connected for an IBM POS terminal interface.
1. Connect the appropriate interface cable to the device, then to the computer.
1-4
Corded Voyager 1450g
RS232 Serial Port Connection:
CCB01-010BT Base
RS485 Connection:
2. Turn the terminal/computer power back on. The scanner beeps.
3. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols in the back of this
manual. The scanner beeps once.
For further RS485 settings, refer to RS485, page 2-2.
1-5
Mounting a CCB01-010BT Charge Base
2.8 in.
72.1mm
3.35 in.
85.09mm
2.36 in.
59.84mm
8x32 thread
x .39 in. (10mm) deep
Reading Techniques
The scanner has a view finder that projects a bright red aiming beam that corresponds to the scanner’s horizontal field of view.
The aiming beam should be centered over the bar code, but it can be positioned in any direction for a good read.
Linear bar code
2D Matrix symbol
The aiming beam or pattern is smaller when the scanner is closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit. Symbologies with larger bars or elements
(mil size) should be read farther from the unit. To read single or multiple symbols (on a page or on an object), hold the scanner
at an appropriate distance from the target, press the trigger, and center the aiming beam or pattern on the symbol. If the code
being scanned is highly reflective (e.g., laminated), it may be necessary to tilt the code up 15° to 18° to prevent unwanted reflection.
Menu Bar Code Security Settings
Honeywell scanners are programmed by scanning menu bar codes or by sending serial commands to the scanner. If you want
to restrict the ability to scan menu codes, you can use the Menu Bar Code Security settings. Please contact the nearest technical support office (see Customer Support on page 13-1) for further information.
1-6
Setting Custom Defaults
You have the ability to create a set of menu commands as your own, custom defaults. To do so, scan the Set Custom Defaults
bar code below before scanning the menu commands for your custom defaults. If a menu command requires scanning numeric
codes from the back cover, then a Save code, that entire sequence will be saved to your custom defaults. When you have
entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults bar code.
Set Custom Defaults
Save Custom Defaults
Note: When using a cordless system, the Custom Defaults settings apply to all workgroups. Scanning the Save Defaults bar
code also causes both the scanner and the base or Access Point to perform a reset and become unlinked. The scanner
must be placed in its base to re-establish the link before any setup codes are entered. If using an Access Point, the linking
bar code must be scanned. See Cordless System Operation beginning on page 3-1 for additional information.
You may have a series of custom settings and want to correct a single setting. To do so, just scan the new setting to overwrite
the old one. For example, if you had previously saved the setting for Beeper Volume at Low to your custom defaults, and decide
you want the beeper volume set to High, just scan the Set Custom Defaults bar code, then scan the Beeper Volume High
menu code, and then Save Custom Defaults. The rest of the custom defaults will remain, but the beeper volume setting will be
updated.
Resetting the Custom Defaults
If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults bar code below. This is
the recommended default bar code for most users. It resets the scanner to the custom default settings. If there are no custom
defaults, it will reset the scanner to the factory default settings. Any settings that have not been specified through the custom
defaults will be defaulted to the factory default settings.
Activate Custom Defaults
Note: If using a cordless system, scanning this bar code also causes both the scanner and the base or Access Point to perform
a reset and become unlinked. The scanner must be placed in its base to re-establish the link. If using an Access Point,
the linking bar code must be scanned. See Cordless System Operation beginning on page 3-1 for additional information.
1-7
1-8
2
Programming the Interface
Introduction
This chapter describes how to program your system for the desired interface.
Programming the Interface - Plug and Play
Plug and Play bar codes provide instant scanner set up for commonly used interfaces.
Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.
Keyboard Wedge
If you want your system programmed for an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard, scan
the bar code below. Keyboard wedge is the default interface.
Note: The following bar code also programs a carriage return (CR) suffix.
IBM PC AT and Compatibles with
CR suffix
Laptop Direct Connect
For most laptops, scanning the Laptop Direct Connect bar code allows operation of the scanner in parallel with the integral
keyboard. The following Laptop Direct Connect bar code also programs a carriage return (CR) suffix and turns on Emulate
External Keyboard (page 2-16).
Laptop Direct Connect
with CR suffix
RS232 Serial Port
The RS232 Interface bar code is used when connecting to the serial port of a PC or terminal. The following RS232 Interface
bar code also programs a carriage return (CR) and a line feed (LF) suffix, baud rate, and data format as indicated below. It also
changes the trigger mode to manual.
Option
Setting
Baud Rate
Data Format
115,200 bps
8 data bits, no parity bit, 1 stop bit
RS232 Interface
2-1
RS485
Scan one of the following “Plug and Play” codes to program the scanner for an IBM POS terminal interface.
Note: After scanning one of these codes, you must power cycle the cash register.
IBM Port 5B Interface
IBM Port 9B
HHBCR-1 Interface
IBM Port 17 Interface
IBM Port 9B
HHBCR-2 Interface
Each bar code above also programs the following suffixes for each symbology:
Symbology
Suffix
Symbology
Suffix
EAN 8
EAN 13
UPC A
UPC E
0C
16
0D
0A
Code 39
Interleaved 2 of 5
Code 128 *
Code 128 **
MaxiCode
00
00
00
00
00
0A
0D
0A
18
2F
0B
0B
0B
0B
0B
* Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B HHBCR-1, and IBM 4683 Port 17 Interfaces
**Suffixes programmed for Code 128 with IBM 4683 Port 9 HHBCR-2 Interface
RS485 Packet Mode
The following selection allows you to break up large bar code data into smaller packets on an IBM POS terminal. To break
up large bar codes into small packets, scan the Packet Mode On bar code below. Scan the Packet Mode Off bar code if you
want large bar code data to be sent to the host in a single chunk. Default = Packet Mode Off.
* Packet Mode Off
Packet Mode On
2-2
RS485 Packet Length
If you are using Packet mode, you can specify the size of the data “packet” that is sent to the host. Scan the Packet
Length bar code, then then the packet size (from 20 - 256) from the Programming Chart inside the back cover of this
manual, then Save. Default = 40.
Packet Length
USB IBM SurePos
Scan one of the following “Plug and Play” codes to program the scanner for an IBM SurePos (USB handheld scanner) or IBM
SurePos (USB tabletop scanner) interface.
Note: After scanning one of these codes, you must power cycle the cash register.
USB IBM SurePos
(USB Handheld Scanner)
Interface
USB IBM SurePos
(USB Tabletop Scanner)
Interface
Each bar code above also programs the following suffixes for each symbology:
Symbology
Suffix
Symbology
Suffix
EAN 8
EAN 13
UPC A
UPC E
0C
16
0D
0A
Code 39
Interleaved 2 of 5
Code 128
Code 39
00
00
00
00
0A
0D
18
0A
0B
0B
0B
0B
USB PC or Macintosh Keyboard
Scan one of the following codes to program the scanner for USB PC Keyboard or USB Macintosh Keyboard. Scanning these
codes also adds a CR and LF.
USB Keyboard (PC)
USB Keyboard (Mac)
USB Japanese Keyboard (PC)
2-3
USB HID
Scan the following code to program the scanner for USB HID bar code scanners.
USB HID Bar Code Scanner
USB Serial
Scan the following code to program the scanner to emulate a regular RS232-based COM Port. If you are using a Microsoft®
Windows® PC, you will need to download a driver from the Honeywell website (www.honeywellaidc.com). The driver will use
the next available COM Port number. Apple® Macintosh computers recognize the scanner as a USB CDC class device and
automatically uses a class driver.
USB Serial
Note: No extra configuration (e.g., baud rate) is necessary.
CTS/RTS Emulation
CTS/RTS Emulation On
* CTS/RTS Emulation Off
ACK/NAK Mode
ACK/NAK Mode On
* ACK/NAK Mode Off
2-4
Remote MasterMind™ for USB
When using a USB interface, you may wish to configure your scanner to communicate with Remote MasterMind Scanner Management Software (ReM). Scan the ReM On bar code to communicate with ReM. To disable this capability, scan ReM Off.
Default = ReM On.
Note: Remote MasterMind settings apply only to the Voyager 1450g. They are not supported by the Voyager 1452g.
ReM Off
* ReM On
Verifone® Ruby Terminal Default Settings
Scan the following Plug and Play code to program the scanner for a Verifone Ruby terminal. This bar code sets the baud rate to
1200 bps and the data format to 8 data bits, mark parity bit, 1 stop bit. It also adds a line feed (LF) suffix and programs the following prefixes for each symbology:
Symbology
Prefix
UPC-A
UPC-E
EAN-8
EAN-13
A
A
FF
F
Verifone Ruby Settings
Gilbarco® Terminal Default Settings
Scan the following Plug and Play code to program the scanner for a Gilbarco terminal. This bar code sets the baud rate to 2400
bps and the data format to 7 data bits, even parity, 2 stop bits. It also also adds a carriage return (CR) suffix and programs the
following prefixes for each symbology:
Symbology
Prefix
UPC-A
UPC-E
EAN-8
EAN-13
A
E0
FF
F
Gilbarco Settings
2-5
Honeywell Bioptic Aux Port Configuration
Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This
bar code sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit.
Honeywell Bioptic Settings
Datalogic™ Magellan© Bioptic Aux Port Configuration
Scan the following Plug and Play code to program the scanner for a Datalogic Magellan bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit.
Datalogic Magellan Bioptic Settings
NCR Bioptic Aux Port Configuration
Scan the following Plug and Play code to program the scanner for an NCR bioptic scanner auxiliary port configuration. The following prefixes are programmed for each symbology:
Symbology
Prefix
Symbology
Prefix
UPC-A
UPC-E
A
E0
b
f
r
EAN-8
FF
EAN-13
Code 39
F
a
Interleaved 2 of 5
Code 128
GS1 DataBar
Omnidirecitonal
GS1 DataBar
Expanded
Codabar
Code 32
Pharmaceutical
(PARAF)
r
N
a
NCR Bioptic Settings
Wincor Nixdorf Terminal Default Settings
Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf terminal. This bar code sets the baud rate
to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit.
Wincor Nixdorf Terminal Settings
2-6
Wincor Nixdorf Beetle™ Terminal Default Settings
Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf Beetle terminal. This bar code sets the
baud rate to 115200 bps and the data format to 8 data bits, no parity, 1 stop bit. The following prefixes are programmed for each
symbology:
Symbology
Prefix
Aztec Code
Codabar
Code 93
Code 128
Data Matrix
EAN-8
EAN-13
GS1 DataBar
GS1-128
V
N
L
K
R
B
A
E
P
Symbology
Interleaved 2 of 5
MaxiCode
MicroPDF417
PDF417
QR Code
Straight 2 of 5 IATA
UPC-A
UPC-E
All other bar codes
Prefix
I
T
S
Q
U
H
A0
C
M
Wincor Nixdorf Beetle Settings
Wincor Nixdorf RS232 Mode A
Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf RS232 Mode A terminal. This bar code sets
the baud rate to 9600 bps and the data format to 8 data bits, odd parity, 1 stop bit. The following prefixes are programmed for
each symbology:
Symbology
Prefix
Code 128
Code 93
Codabar
UPC-A
UPC-E
EAN-8
All other bar codes
K
L
N
A0
C
B
M
Symbology
EAN-13
GS1-128
Interleaved 2 of 5
Plessey
Straight 2 of 5 IATA
GS1 DataBar
Prefix
A
K
I
O
H
E
Wincor Nixdorf RS232 Mode A
Settings
2-7
Keyboard Country Layout
Scan the appropriate country code below to program the keyboard layout for your country or language. As a general rule, the
following characters are supported, but need special care for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
Keyboard Countries
* United States
Albania
Azeri (Cyrillic)
Azeri (Latin)
Belarus
Belgium
Bosnia
Brazil
Brazil (MS)
Bulgaria (Cyrillic)
2-8
Keyboard Countries (Continued)
Bulgaria (Latin)
Canada (French legacy)
Canada (French)
Canada (Multilingual)
Croatia
Czech
Czech (Programmers)
Czech (QWERTY)
Czech (QWERTZ)
Denmark
Dutch (Netherlands)
2-9
Keyboard Countries (Continued)
Estonia
Faroese
Finland
France
Gaelic
Germany
Greek
Greek (220 Latin)
Greek (220)
Greek (319 Latin)
Greek (319)
2 - 10
Keyboard Countries (Continued)
Greek (Latin)
Greek (MS)
Greek (Polytonic)
Hebrew
Hungarian (101 key)
Hungary
Iceland
Irish
Italian (142)
Italy
Japan ASCII
2 - 11
Keyboard Countries (Continued)
Kazakh
Kyrgyz (Cyrillic)
Latin America
Latvia
Latvia (QWERTY)
Lithuania
Lithuania (IBM)
Macedonia
Malta
Mongolian (Cyrillic)
Norway
2 - 12
Keyboard Countries (Continued)
Poland
Polish (214)
Polish (Programmers)
Portugal
Romania
Russia
Russian (MS)
Russian (Typewriter)
SCS
Serbia (Cyrillic)
Serbia (Latin)
2 - 13
Keyboard Countries (Continued)
Slovakia
Slovakia (QWERTY)
Slovakia (QWERTZ)
Slovenia
Spain
Spanish variation
Sweden
Switzerland (French)
Switzerland (German)
Tatar
Turkey F
2 - 14
Keyboard Countries (Continued)
Turkey Q
Ukrainian
United Kingdom
United States (Dvorak)
United States (Dvorak left)
United Stated (Dvorak right)
United States (International)
Uzbek (Cyrillic)
Keyboard Style
This programs keyboard styles, such as Caps Lock and Shift Lock. If you have used Keyboard Conversion settings, they will
override any of the following Keyboard Style settings. Default = Regular.
Regular is used when you normally have the Caps Lock key off.
* Regular
Caps Lock is used when you normally have the Caps Lock key on.
Caps Lock
2 - 15
Shift Lock is used when you normally have the Shift Lock key on (not common to U.S. keyboards).
Shift Lock
Automatic Caps Lock is used if you change the Caps Lock key on and off. The software tracks and reflects if you have Caps
Lock on or off . This selection can only be used with systems that have an LED that notes the Caps Lock status (AT keyboards).
Automatic Caps Lock
Autocaps via NumLock bar code should be scanned in countries (e.g., Germany, France) where the Caps Lock key cannot be
used to toggle Caps Lock. The NumLock option works similarly to the regular Autocaps, but uses the NumLock key to retrieve
the current state of the Caps Lock.
Autocaps via NumLock
Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent).
Emulate External Keyboard
Note: After scanning the Emulate External Keyboard bar code, you must power cycle your computer.
Keyboard Conversion
Alphabetic keyboard characters can be forced to be all upper case or all lowercase. So if you have the following bar code:
“abc569GK,” you can make the output “ABC569GK” by scanning Convert All Characters to Upper Case, or to “abc569gk” by
scanning Convert All Characters to Lower Case.
These settings override Keyboard Style selections.
Note: If your interface is a keyboard wedge, first scan the menu code for Automatic Caps Lock (page 2-16). Otherwise, your
output may not be as expected.
Default = Keyboard Conversion Off.
* Keyboard Conversion Off
Convert All Characters
to Upper Case
Convert All Characters
to Lower Case
2 - 16
Control Character Output
This selection sends a text string instead of a control character. For example, when the control character for a carriage return is
expected, the output would display [CR] instead of the ASCII code of 0D. Refer to ASCII Conversion Chart (Code Page
1252) on page A-3. Only codes 00 through 1F are converted (the first column of the chart). Default = Off.
Note: Control + ASCII Mode overrides this mode.
Control Character Output On
* Control Character Output Off
Keyboard Modifiers
This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode.
Control + ASCII Mode On: The scanner sends key combinations for ASCII control characters for values 00-1F. Windows is
the preferred mode. All keyboard country codes are supported. DOS mode is a legacy mode, and it does not support all keyboard country codes. New users should use the Windows mode. Refer to Keyboard Function Relationships, page 8-1 for
CTRL+ ASCII Values.
Windows Mode Prefix/Suffix Off: The scanner sends key combinations for ASCII control characters for values 00-1F, but it
does not translate any prefix or suffix information.
Default = Control + ASCII Mode Off.
Windows Mode Control + X
Mode On
* Control + X Mode Off
DOS Mode Control + X Mode On
Windows Mode Prefix/Suffix Off
2 - 17
Turbo Mode: The scanner sends characters to a terminal faster. If the terminal drops characters, do not use Turbo Mode.
Default = Off.
Turbo Mode On
* Turbo Mode Off
Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off.
Numeric Keypad Mode On
* Numeric Keypad Mode Off
Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping
characters. Default = Off.
Automatic Direct Connect Mode
On
* Automatic Direct Connect
Mode Off
RS232 Modifiers
RS232 Baud Rate
Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the
same baud rate as the scanner. Default = 9600.
300
600
2 - 18
1200
2400
4800
* 9600
19200
38400
57,600
115,200
RS232 Word Length: Data Bits, Stop Bits, and Parity
Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0
through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications that require use of the full ASCII set,
select 8 data bits per character. Default = 8.
Stop Bits sets the stop bits at 1 or 2. Default = 1.
Parity provides a means of checking character bit patterns for validity.
Default = None.
7 Data, 1 Stop, Parity Even
2 - 19
7 Data, 1 Stop, Parity None
7 Data, 1 Stop, Parity Odd
7 Data, 2 Stop, Parity Even
7 Data, 2 Stop Parity None
7 Data, 2 Stop, Parity Odd
8 Data, 1 Stop, Parity Even
* 8 Data, 1 Stop, Parity None
8 Data, 1 Stop, Parity Odd
RS232 Receiver Time-Out
The unit stays awake to receive data until the RS232 Receiver Time-Out expires. A manual trigger resets the time-out.
When an RS232 receiver is sleeping, a character may be sent to wake up the receiver and reset the time-out. A transaction
on the CTS line will also wake up the receiver. The receiver takes 300 milliseconds to completely come up. Change the
RS232 receiver time-out by scanning the bar code below, then scanning digits from the inside back cover of this manual,
then scanning Save. The range is 0 to 300 seconds. Default = 0 seconds (no time-out - always on).
RS232 Receiver Time-Out
RS232 Handshaking
RS232 Handshaking allows control of data transmission from the scanner using software commands from the host device.
When RTS/CTS is turned Off, no data flow control is used.
Flow Control, No Timeout: The scanner asserts RTS when it has data to send, and will wait indefinitely for CTS to be
asserted by the host.
2 - 20
Two-Direction Flow Control: The scanner asserts RTS when it is OK for the host to transmit. The host asserts CTS
when it is OK for the device to transmit.
Flow Control with Timeout: The scanner asserts RTS when it has data to send and waits for a delay (see RS232
Timeout on page 2-21) for CTS to be asserted by the host. If the delay time expires and CTS is not asserted, the device
transmit buffer is cleared and scanning may resume. Default = RTS/CTS Off.
Flow Control, No Timeout
Two-Direction Flow Control
Flow Control with Timeout
* RTS/CTS Off
RS232 Timeout
When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host.
Set the length (in milliseconds) for a timeout by scanning the bar code below, then setting the timeout (from 1-5100 milliseconds) by scanning digits from the inside back cover, then scanning Save.
RS232 Timeout
XON/XOFF
Standard ASCII control characters can be used to tell the scanner to start sending data (XON/XOFF On) or to stop sending
data (XON/XOFF Off). When the host sends the XOFF character (DC3, hex 13) to the scanner, data transmission stops.
To resume transmission, the host sends the XON character (DC1, hex 11). Data transmission continues where it left off
when XOFF was sent. Default = XON/XOFF Off.
XON/XOFF On
* XON/XOFF Off
2 - 21
ACK/NAK
After transmitting data, the scanner waits for an ACK character (hex 06) or a NAK character (hex 15) response from the
host. If ACK is received, the communications cycle is completed and the scanner looks for more bar codes. If NAK is
received, the last set of bar code data is retransmitted and the scanner waits for ACK/NAK again. Turn on the ACK/NAK
protocol by scanning the ACK/NAK On bar code below. To turn off the protocol, scan ACK/NAK Off. Default = ACK/NAK
Off.
ACK/NAK On
* ACK/NAK Off
Scanner to Bioptic Communication
The following settings are used to set up communication between Honeywell scanners and bioptic scanners.
Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with
a bioptic scanner. See "RS232 Baud Rate" on page 2-18, and RS232 Timeout on page 2-21 for further information.
Scanner-Bioptic Packet Mode
Packet Mode On must be scanned to set the scanner’s format so it is compatible with a bioptic scanner. Default = Packet
Mode Off.
* Packet Mode Off
Packet Mode On
Scanner-Bioptic ACK/NAK Mode
Bioptic ACK/Nak On must be scanned so the scanner will wait for an ACK or NAK from a bioptic scanner after each packet
is sent. The Scanner-Bioptic ACK/NAK Timeout (below) controls how long the scanner will wait for a response. Default =
Bioptic ACK/NAK Off.
* Bioptic ACK/NAK Off
Bioptic ACK/NAK On
2 - 22
Scanner-Bioptic ACK/NAK Timeout
This allows you to set the length (in milliseconds) for a timeout for a bioptic scanner’s ACK/NAK response. Scan the bar
code below, then set the timeout (from 1-30,000 milliseconds) by scanning digits from the inside back cover, then scanning
Save. Default = 5100.
ACK/NAK Timeout
2 - 23
2 - 24
3
Cordless System Operation
Note: This chapter applies only to cordless scanning systems. It does not apply to corded scanners.
How the Cordless Charge Base/Access Point Works
A cordless charge base or an Access Point provide the link between the cordless scanner and the host system. The base/
Access Point contains an interface assembly and an RF communication module. The RF communication module performs the
data exchange between the cordless scanner and the interface assembly. The control assembly coordinates the central interface activities including: transmitting/receiving commands and data to/from the host system, performing software activities
(parameter menuing, visual indicator support, power-on diagnostics), and data translation required for the host system.
The cordless charge base is also a scanner’s battery charger. Refer to Charging Information, page 3-4, for additional information.
Linking the Scanner to a Charge Base
Turn off power before connecting a base, then power up the computer once the base is fully connected. When the base is connected and powered up, put the scanner in the base to establish a link. The green LED on the base flashes to indicate the scanner’s battery is charging.
If the scanner and base have previously been linked, you do not receive any feedback. If this is the first time that the scanner
and base are linked, both devices emit a short chirp when their radios link. At this point, that one scanner is linked to one base.
CCB01-010BT Charge Base
Page Button and Base LEDs
To determine if your cordless system is set up correctly, scan one of the sample bar codes in the back of this manual. If the
scanner provides a single good read beep and the green LED lights, the scanner has successfully linked to the base. If you
receive an error tone and the red LED lights, the scanner has not linked to the base. Refer to page 12-4 for troubleshooting
information.
Linking the Scanner to an Access Point
Turn on the computer (laptop/desktop). Plug the interface cable into the Access Point first and
then into the appropriate port on the computer. The Page button lights up when the connection to
the host is made.
Page
Button
3-1
Scan the linking bar code on the top of the Access Point to establish a connection
between the Access Point and the scanner. The scanner emits a short beep and
flashes the green LED to confirm a connection with the Access Point. The Access
Point’s Page button remains blue.
Replacing a Linked Scanner
If you need to replace a broken or lost scanner that is linked to a base or an Access Point, scan the Override Locked Scanner
bar code below with a new scanner and place that scanner in the base, or scan the Access Point linking bar code. The locked
link will be overridden; the broken or lost scanner’s link with the base or Access Point will be removed, and the new scanner will
be linked.
Override Locked Scanner
(Single Scanner)
Communication Between the Cordless System
and the Host
The cordless scanner provides immediate feedback in the form of a “good read” indication with a green LED on the scanner and
an audible beep. This indicates that the bar code has been scanned correctly and the base or Access Point has acknowledged
receiving the data. This is possible since the cordless system provides two-way communication between the scanner and the
base or Access Point.
When data is scanned, the data is sent to the host system via the base or Access Point. The cordless scanner recognizes data
acknowledgement (ACK) from the base or Access Point. If it cannot be determined that the data has been properly sent to the
base or Access Point, the scanner issues an error indication. You must then check to see if the scanned data was received by
the host system.
2
2
1
1. Scanner reads code and gets ACK from base or Access Point
2. Base or Access Point sends data to host
3-2
Programming the Scanner and Base or Access Point
When using the scanner and charge base or Access Point together as a system, menu parameters and configuration settings
are stored in the charge base or Access Point. Therefore, when programming any menu configuration settings, the scanner
must be linked to the intended charge base or Access Point.
Note: This only applies when the scanner is linked to a charge base or Access Point. If the scanner is in a non-base mode,
configuration settings are stored in the scanner.
RF (Radio Frequency) Module Operation
The cordless system uses a two-way Bluetooth® radio to transmit and receive data between the scanner and the base or
Access Point. Designed for point-to-point and multipoint-to-single point applications, the radio operates using a license free ISM
band, which sends relatively small data packets at a fast data rate over a radio signal with randomly changing frequencies,
makes the cordless system highly responsive to a wide variety of data collection applications and resistant to noisy RF environments. The CCB01-010BT (Bluetooth Class 2) provides a communication range of 33 feet (10m) between the scanner and
base or Access Point, depending on the environment. See Flexible Power Management, page 3-12, for information about controlling this range.
System Conditions
The components of the cordless system interact in specific ways as you associate a scanner to a base or Access Point, as you
move a scanner out of range, bring a scanner back in range, or swap scanners between two cordless systems. The following
information explains the cordless system operating conditions.
Linking Process
Once a scanner is placed into a cordless charge base, the scanner’s battery charge status is checked, and software automatically detects the scanner and links it to the base depending on the selected link mode.
Refer to Linking the Scanner to an Access Point, page 3-1, for information about linking to an Access Point.
Scanner Is Out of Range
The cordless scanner is in communication with its base or Access Point, even when it is not transmitting bar code data.
Whenever the scanner can’t communicate with the base or Access Point for a few seconds, it is out of range. If the scanner
is out of range and you scan a bar code, the scanner issues an error tone indicating no communication with the base or
Access Point. A cordless charge base can also sound an alarm. Refer to Out-of-Range Alarm, page 3-10.
Scanner Is Moved Back Into Range
The scanner relinks if the scanner or the base or Access Point have been reset, or the scanner comes back into range. If
the scanner relinks, you will hear a single chirp when the relinking process (uploading of the parameter table) is complete.
Refer to Out-of-Range Alarm on page 3-10 for further information.
Out of Range and Back into Range with Batch Mode On
The scanner may store a number of symbols (approximately 500 U.P.C. symbols; others may vary) when it is out of range
and then send them to the base or Access Point when back in range (see Batch Mode on page 3-13).
You will not hear a communication error tone in this mode, but you will hear a short buzz when you pull the trigger if the
radio communication is not working. Once the radio connection is made, the scanner produces a series of beeps while the
data is being transferred to the base or Access Point.
Page Button
When you press the Page button on the base or Access Point, the scanners associated with that base or Access Point will
begin beeping (3 short and 1 long beep). If you pull the trigger on a scanner that is beeping in response, or press the Page
button on the base or Access Point a second time, all associated scanners will stop beeping. See Paging on page 3-7 for
further information about Page Button settings.
3-3
About the Battery
There is a danger of explosion if the batteries are incorrectly replaced. Replace the batteries with only the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the recycle program for
batteries as directed by the governing agency for the country where the batteries are to be discarded.
!
Power is supplied to the cordless scanner by a rechargeable battery that is integrated in the scanner handle. Batteries are
shipped approximately 30% to 60% charged. The battery should be charged for a minimum of 4 hours before initial use to
ensure optimal performance.
Charging Information
The battery is designed to charge while the scanner is positioned in the cordless base unit. Refer to Base/Access Point
LED Sequences and Meaning, page 3-5, for an interpretation of the Charge Status indicators. Refer to Charge Only Mode
(page 3-9) if you need to charge a scanner without linking it to the base.
Place the scanner in the base that is connected to an appropriate power supply. Use only a Listed Limited Power Source
(LPS) or Class 2 type power supply with output rated 5 to 5.2Vdc, 1A.
Note: If you are powering the base through the interface cable (for example, a USB cable) and not using an external power
supply plugged into the aux port, the current available for charging is reduced and charge times are increased.
Battery Recommendations
• The battery is a lithium ion cell and can be used without a full charge, and can also be charged without fully discharging,
without impacting the battery life. There is no need to perform any charge/discharge conditioning on this type of battery.
• Keep the base connected to power when the host is not in use.
• Replace a defective battery immediately since it could damage the scanner.
• Although your battery can be recharged many times, it will eventually be depleted. Replace it after the battery is unable
to hold an adequate charge.
• If you are not sure if the battery or charger is working properly, send it to Honeywell International Inc. or an authorized
service center for inspection. Refer to Customer Support on page 13-1 for additional information.
!
Caution:
Use only Honeywell Li-ion battery packs, model number BAT-SCN01, rated 3.7 Vdc, 7.4Whr in this device. Use
of any non-Honeywell battery may result in damage not covered by the warranty.
Safety Precautions for Lithium Batteries
•
•
•
•
•
•
•
Do not place batteries in fire or heat the batteries.
Do not store batteries near fire or other high temperature locations.
Do not store or carry batteries together with metal objects.
Do not expose batteries to water or allow the batteries to get wet.
Do not connect (short) the positive and negative terminals, of the batteries, to each other with any metal object.
Do not pierce, strike or step on batteries or subject batteries to strong impacts or shocks.
Do not disassemble or modify batteries.
!
Caution:
Danger of explosion if batteries are incorrectly replaced. Dispose of used batteries according to the recycle
program for batteries as directed by the governing agency for the country where the batteries are to be
discarded.
Proper Disposal of the Battery
When the battery has reached the end of its useful life, the battery should be disposed of by a qualified
recycler or hazardous materials handler. Do not incinerate the battery or dispose of the battery with general waste materials. You may send the scanner’s battery to us. (postage paid). The shipper is responsible for complying with all federal, state, and local laws and regulations related to the packing, labeling,
manifesting, and shipping of spent batteries. Contact the Product Service Department (page 13-1) for
recycling or disposal information. Since you may find that your cost of returning the batteries significant,
it may be more cost effective to locate a local recycle/disposal company.
3-4
Beeper and LED Sequences and Meaning
The scanner contains LEDs on the rear of the unit that indicate linking status, decoding state, and battery condition. The base
has LEDs on the top of the unit that indicate its power up, communication, and battery charge condition. The red LED = error;
green LED = success of any type. Scanners and the CCB01-010BT base have audible indicators as well: 1 razz or error tone =
error; 2 beeps = menu change; 1 beep = all other successes.
The table below lists the indication and cause of the LED indication, beeps, and vibrations for the scanner.
Scanner LED Sequences and Meaning
LED Indication
Normal Operation
Red Flash
Green Flash
Red, blinking
Menu Operation
Green Flash
Red, blinking
Beeper Indication
Vibrate Indication
Cause
None
1 beep
Razz or error tone
None
None
None
Battery low
Successful communication or linking
Failed communication
2 beeps
Razz or error tone
2 vibrations
1 long vibration
Successful menu change
Unsuccessful menu change
Base/Access Point LED Sequences and Meaning
The base contains a red LED and the Access Point has a blue LED that indicate the status of the unit and verifies its communication with the host system. The base also has a green LED that indicates scanner battery charge condition.
Red or Blue LED - Host Communication
Red or Blue LED
Communication Condition
Off
USB suspend
On continuously
Power on, system idle
Short blinks in multiple pulses. Occurs while transferring data to/
from the RF module or the Host port.
Receiving data
Green LED - Scanner Battery
(base only, does not apply to Access Point)
Green LED
Charge Condition
Off
Battery not detected or charge suspended
Slow flash, 1 second on, 1 second off
Pre-charge and charging
On continuously
Charge complete
Fast flash, 300 mSec on, 300 mSec off
Charge Error
Base Power Communication Indicator
To display the power indicator on a base or an Access Point, scan the Base Power Communication Indicator On bar
code. To turn off the power indicator, scan the Off bar code. Default = On.
* Base Power Communication
Indicator On
3-5
Base Power Communication
Indicator Off
Reset Scanner
Scanning this bar code reboots the scanner and causes it to relink with the base or Access Point.
Reset Scanner
Scanning While in Base Cradle
If you want to be able to scan bar codes while the scanner is in the base cradle, scan the Scanning in Cradle On bar code
below. If you want to only allow scanning when the scanner is out of the base cradle, scan Scanning in Cradle Off. If you want
the scanner to shut down when in the base cradle, scan Shut Down Scanner in Cradle. Default = Scanning in Cradle On.
Scanning in Cradle Off
* Scanning in Cradle On
Shut Down Scanner in Cradle
Base Charging Modes
When the base has both an external power supply (plugged into the auxiliary power port) and a host interface cable, it will draw
its power from the external power supply. When the base does not have an external power supply, it draws its power from the
interface cable. However, the scanner battery charges more slowly from a host interface cable than if auxiliary power were
available. Using the following selections, you can specify whether the scanner battery is charged from power supplied via the
host interface cable.
When Base Charge Off is selected, the scanner battery does not charge when the scanner is in the base cradle.
When External or Interface Cable Power is selected, the scanner battery charges from the base’s external power supply, if
there is one. If there is no external power supply to the base, the scanner battery charges from the interface cable.
When External Power Only is selected, the scanner battery only charges from the base’s external power supply. If there is no
external power supply, the scanner battery does not charge.
Note: If you are using a cordless charge base in Presentation Mode, External Power Only is the only setting available.
3-6
Default = External or Interface Cable Power.
Base Charge Off
External or Interface Cable
Power
External Power Only
Paging
Paging Mode
By default, the paging button on the base or Access Point pages the scanners associated with that base or Access Point. If
you want the paging button on your base or Access Point to be disabled, scan the Paging Mode Off bar code, below.
When Paging Mode is off, the base or Access Point will no longer page scanners when the button is pressed. The red LED
on the base or blue LED on the Access Point will remain lit to indicate that Paging Mode is off. (This light will go out when
the button is pressed, then back on when it’s released.) Default = Paging Mode On.
* Paging Mode On
Paging Mode Off
Paging Pitch
When you press the Page button on the base or Access Point, the scanners associated with that base or Access Point will
begin beeping (see Page Button on page 3-3). You can set the pitch of the paging beep for each scanner by scanning one
of the following bar codes. Default = Low.
* Low (1000 Hz)
Medium (3250 Hz)
3-7
High (4200 Hz)
Error Indicators
Beeper Pitch - Base Error
The CCB01-010BT base can be configured to beep at a particular pitch when an error occurs, such as transmission problems to a host system. The beeper pitch codes modify the pitch (frequency) of the error tone the base emits when there is
an error. Default = Low.
* Razz (250 Hz)
Medium (3250 Hz)
High (4200 Hz)
Number of Beeps - Base Error
The number of beeps and LED flashes emitted by the CCB01-010BT base for an error condition can be programmed from
1 - 9. For example, if you program this option to have five error beeps, there will be five error beeps and five LED flashes in
response to an error. To change the number of error beeps, scan the bar code below and then scan a digit (1-9) bar code
and the Save bar code on the Programming Chart inside the back cover of this manual. Default = 1.
Number of Base Error Beeps/LED Flashes
Scanner Report
Scan the bar code below to generate a report for the connected scanners. The report indicates the port, work group, scanner
name, and address. To assign a name to your scanner, refer to Menu Command Syntax, page 10-1.
Scanner Report
3-8
Scanner Address
Scan the bar code below to determine the address of the scanner you are using.
Scanner Address
Base or Access Point Address
Scan the bar code below to determine the address of the base or Access Point you are using.
Base Address
Scanner Modes
Your scanner is capable of working in single scanner mode, multiple scanner mode, or with Bluetooth devices other than the
charge base or Access Point.
Charge Only Mode
There may be times when you want to charge your scanner, but not link to the base. For example, if a scanner is linked to
an Access Point or other Bluetooth device and you need to charge the scanner, but want to retain your existing link.
In order to program the base for Charge Only Mode, you must link a scanner to it. Once the scanner is linked to the base,
scan the Charge Only Mode bar code. Any subsequent scanners placed in that base will charge without linking to it. The
scanner used to program the base remains linked to the base. To unlink this scanner, scan Unlink Scanner on page 3-10.
Charge Only Mode
Note: When in Charge Only Mode, the scanner periodically wakes up and beeps. See "Power Up Beeper" on page 4-1 to
change this setting.
If you want to charge a scanner and link to the base, use Charge and Link Mode. If the base is programmed for Charge
Only Mode, you must link a scanner to it first in order to program it for Charge and Link Mode. Scan the linking bar code on
the base to link the scanner, then scan Charge and Link Mode. Default = Charge and Link Mode.
* Charge and Link Mode
Linked Modes
Locked Link Mode and Open Link Mode are the link modes that accommodate different applications. Scan the appropriate
bar codes included in the Open Link and Locked Link Mode explanations that follow to switch from one mode to another.
Default = Open Link Mode.
3-9
Locked Link Mode - Single Scanner
If you link a scanner to a base or an Access Point using the Locked Link Mode, other scanners are blocked from being
linked if they are inadvertently placed into the base, or if the Access Point linking bar code is scanned. If you do place
a different scanner into a base, it will charge the scanner, but the scanner will not be linked.
Locked Link Mode
(Single Scanner)
To use a different scanner, you need to unlink the original scanner by scanning the Unlink Scanner bar code. (See
Scanner Modes, page 3-9.)
Open Link Mode - Single Scanner
When newly shipped or defaulted to factory settings, a scanner is not linked to a base or an Access Point. A link is
established when the scanner is placed into a base, or an Access Point linking bar code is scanned. When in Open
Link Mode, a new link is established when a new scanner is placed in the base, or you scan an Access Point linking bar
code. Each time a scanner is placed into a base or scans an Access Point linking bar code, the scanner becomes
linked to the base or Access point and the old scanner is unlinked.
* Open Link Mode
(Single Scanner)
Unlinking the Scanner
If a base or an Access Point has a scanner linked to it, that scanner must be unlinked before a new scanner can be linked.
Once the previous scanner is unlinked, it will no longer communicate with the base or Access Point. To unlink the scanner from
a base or an Access Point, scan the Unlink Scanner bar code below.
Unlink Scanner
Override Locked Scanner
If you need to replace a broken or lost scanner that is linked to a base or an Access Point, scan the Override Locked
Scanner bar code below with a new scanner and place that scanner in the base, or scan the Access Point linking bar code.
The locked link will be overridden; the broken or lost scanner’s link with the base or Access Point will be removed, and the
new scanner will be linked.
Override Locked Scanner
(Single Scanner)
Out-of-Range Alarm
If your scanner is out range of the base, an alarm sounds from both your base and scanner. If your scanner is out range of an
Access Point, an alarm sounds from just the scanner. The alarm stops when the scanner is moved closer to the base or Access
Point, when the base or Access Point connects to another scanner, or when the alarm duration expires. To activate the alarm
3 - 10
options for the scanner or the base and to set the alarm duration, scan the appropriate bar code below and then set the time-out
duration (from 0-3000 seconds) by scanning digits on the Programming Chart inside the back cover, then scanning Save.
Default = 0 sec (no alarm).
Base Alarm Duration
Note: The Access Point does not have a base alarm.
Scanner Alarm Duration
Note: If you are out of range when you scan a bar code, you will receive an error tone even if you do not have the alarm set.
You receive the error tone since the data could not be communicated to the base or Access Point or the host.
Alarm Sound Type
You may change the alarm type for the scanner or a CCB01-010BT base by scanning the appropriate bar code below and
then scanning a digit (0-7) bar code and the Save bar code on the Programming Chart inside the back cover of this manual.
Default = 0.
The sounds are as follows:
Setting
Sound
0
3 long beeps, medium pitch
1
3 long beeps, high pitch
2
4 short beeps, medium pitch
3
4 short beeps, high pitch
4
single chirps, medium pitch
5
2 chirps, then 1 chirp, medium pitch
6
single chirps, high pitch
7
2 chirps, then 1 chirp, high pitch
Base Alarm Type
Scanner Alarm Type
Scanner Power Time-Out Timer
Note: Scanner Power Time-out Timer only applies to cordless systems. It does not apply to corded scanners.
When there is no activity within a specified time period, the scanner enters low power mode. Scan the appropriate scanner
power time-out bar code to change the time-out duration (in seconds).
Note: Scanning zero (0) is the equivalent of setting no time-out.
3 - 11
If there are no trigger pulls during the timer interval, the scanner goes into power down mode. Whenever the trigger is enabled,
the timer is reset. If the scanner is placed in the charge base cradle and the battery is in the process of being charged, the
scanner will not go into power down mode. Default = 3600 seconds.
0 seconds
200 seconds
400 seconds
900 seconds
* 3600 seconds
7200 seconds
Note: When the scanner is in power down mode, pull the trigger to power the unit back up. There will be a set of power up beeps
and a delay of up to a few seconds for the radio to join. The scanner will then be ready to use.
Flexible Power Management
If you are experiencing network performance issues, and suspect the scanner is interfering with other devices, you can turn
down the power output of the scanner. This reduces the range between the scanner and a base or an Access Point as shown
in the following illustration:
802.11
LAN
1902
Scanner
Red
r
uced Powe
Full Power
3 - 12
Scan one of the bar codes below to set the scanner’s power output to Full Power (100%), Medium Power (35%), Medium Low
Power (5%), or Low Power (1%). Default = Full Power.
* Full Power
Medium Power
Medium Low Power
Low Power
Batch Mode
Batch mode is used to store bar code data when a scanner is out of range of its base or Access Point, or when performing
inventory. The data is transmitted to the base or Access Point once the scanner is back in range or when the records are manually transmitted.
Note: Batch mode has limitations when using multiple scanners to one base or Access Point. If a cordless system is being used
in "multiple link mode," where up to 7 scanners are to be connected to one base or Access Point, some accumulated or
batched scans could be lost if scanners are constantly being moved in and out of range.
Automatic Batch Mode stores bar code data when the scanner is out of range of the base or Access Point. The data is automatically transmitted to the base or Access Point once the scanner is back in range. When the scanner’s buffer space is full,
any bar codes scanned generate an error tone. In order to scan bar codes again, the scanner must be moved back into range
of the base or Access Point so data can be transmitted.
Inventory Batch Mode stores bar code data, whether or not you are in range of the base or Access Point. To transmit the
stored data to the base or Access Point, either place the scanner in the base, or scan Transmit Inventory Records (page 3-17).
When the scanner’s buffer space is full, any bar codes scanned generate an error tone. In order to scan bar codes again, the
data must be transmitted to the base or Access Point. Once the data is transmitted, it is cleared in the scanner.
Persistent Batch Mode is the same as Inventory Batch Mode, except that once the data is transmitted to the base or Access
Point, it is retained in the scanner. If you want to transmit more than once, you can do so using this mode. In order to clear the
scanner’s buffer, you must scan Clear All Codes (see page 3-17).
Default = Batch Mode Off.
* Batch Mode Off
Automatic Batch Mode
3 - 13
Inventory Batch Mode
Persistent Batch Mode
Batch Mode Beep
When scanning in Inventory Batch Mode (page 3-14), the scanner beeps every time a bar code is scanned. When Batch
Mode Beep is On, you will also hear a click when each bar code is sent to the host. If you do not want to hear these clicks,
scan Batch Mode Beep Off. Default = Batch Mode Beep On.
Batch Mode Beep Off
* Batch Mode Beep On
Batch Mode Storage
When a scanner is storing data during a Batch Mode process, you can select whether the data is stored in Flash memory
or in RAM.
Flash Storage: The scanner writes any untransmitted data to flash memory prior to powering down. The data will still be
there when the scanner powers back up. However, the scanner will power down, even with untransmitted data, if it reaches
a power down timeout or if the battery power is very low.
RAM Storage: The scanner will not power down while it contains data that has not been transmitted to the base or Access
Point, even if it reaches a power down timeout. However, if the scanner runs out of battery power, it will power down and
the data will be lost.
Default = Flash Storage.
* Flash Storage
RAM Storage
3 - 14
Batch Mode Quantity
When in Batch Mode, you may wish to transmit the number of multiple bar codes scanned, rather than a single bar code
multiple times. For example, if you scan three bar codes called XYZ with Batch Mode Quantity Off, when you transmit
your data it will appear as XYZ three times. Using Batch Mode Quantity On and the Quantity Codes (page 3-16), you
could output your data as “XYZ, 00003” instead.
Note: If you wish to format your output, for example, place a CR or tab between the bar code data and the quantity, refer
to Data Formatting beginning on page 6-1.
Default = Batch Mode Quantity Off.
* Batch Mode Quantity Off
Batch Mode Quantity On
Entering Quantities
Quantity Codes (page 3-16) allow you to enter a quantity for the last item scanned, up to 9999 (default = 1). Quantity digits
are shifted from right to left, so if a 5th digit is scanned, the 1st digit scanned is discarded and the 2nd, 3rd and 4th digits
are moved to the left to accommodate the new digit.
For example, if the Quantity 5 bar code is scanned after the quantity has been set to 1234, then the 1 is dropped, the quantity will be 2345.
Example: Add a quantity of 5 for the last item scanned.
1. Scan the item's bar code.
2. Scan the quantity 5 bar code.
Example: Add a quantity of 1,500 for the last item scanned.
1. Scan the item's bar code.
2. Scan the quantity 1 bar code.
3. Scan the quantity 5 bar code.
4. Scan the quantity 0 bar code.
5. Scan the quantity 0 bar code.
Example: Change a quantity of 103 to 10.
To correct an incorrect quantity, scan the quantity 0 bar code to replace the incorrect digits, then scan the correct quantity
bar codes.
1. Scan the quantity 0 bar code to change the quantity to 1030.
2. Scan the quantity 0 bar code to change the quantity to 0300.
3. Scan the quantity 1 bar code to change the quantity to 3001.
4. Scan the quantity 0 bar code to change the quantity to 0010.
Default = 1.
Quantity Codes
0
3 - 15
1
2
3
4
5
6
7
8
9
Batch Mode Output Order
When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in first-out).
Default = Batch Mode FIFO.
* Batch Mode FIFO
Batch Mode LIFO
3 - 16
Total Records
If you wish to output the total number of bar codes scanned when in Batch Mode, scan Total Records.
Total Records
Delete Last Code
If you want to delete the last bar code scanned when in Batch Mode, scan Delete Last Code.
Delete Last Code
Clear All Codes
If you want to clear the scanner’s buffer of all data accumulated in Batch Mode, scan Clear All Codes.
Clear All Codes
Transmit Records to Host
If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 3-14), you must scan the following bar
code to transmit all the stored data to the host system.
Transmit Inventory Records
Batch Mode Transmit Delay
Sometimes when accumulated scans are sent to the host system, the transmission of those scans is too fast for the application to process. To program a transmit delay between accumulated scans, scan one of the following delays. Default =
Off.
Note: In most cases, a short (250 ms (milliseconds)) delay is ideal, however, longer delays may be programmed. Contact
Technical Support (page 13-1) for additional information.
* Batch Mode Transmit Delay Off
(No Delay)
Batch Mode Transmit Delay Short
(250 ms)
3 - 17
Batch Mode Transmit Delay Medium
(500 ms)
Batch Mode Transmit Delay Long
(1000 ms)
Multiple Scanner Operation
Note: Multiple Scanner Operation Mode allows you to link up to 7 scanners to one base or Access Point. You cannot join an
8th scanner until you unlink one of the 7 scanners or take a scanner out of range.
To put the scanner in multiple scanner mode, scan the bar code below. Once you scan this bar code, the scanner is unlinked
from the base or Access Point and must either be placed into the base, or you must scan the Access Point linking bar code in
order to relink.
Multiple Scanner Operation
Scanner Name
You may assign a name to each scanner you are using for identification purposes. For example, you may want to have a unique
identifier for a scanner that is receiving imaging commands sent from the base or Access Point.
The default name is in the format “ScannerName_Model_SN_XXXXXXXXXX” If you have more than one scanner linked to a
base, and they all have the same name, the first scanner linked to the base receives commands. When renaming a series of
scanners with identical names, unlink all except one of the scanners from the base.
Perform the rename operation using either the bar codes on page 3-19, or by sending the serial command :ScannerName:BT_NAMNewName. where ScannerName is the current name of the scanner, and NewName is the new name for the
scanner. If you wish to change the names of additional scanners, link them one at a time and repeat the :ScannerName:BT_NAMNewName. command for each scanner.
To rename scanners with sequential, numeric names, scan the bar codes below. Scan the Reset code after each name change
and wait for the scanner to relink to the base or Access Point before scanning a bar code to rename the next scanner.
0001
0002
0003
3 - 18
0004
0005
0006
0007
Reset
You may also scan the Scanner Name bar code below and scan a number for the scanner name. For example, if you wanted to
name the linked scanner “312,” you would scan the bar code below, scan the 3, 1, and 2 bar codes on the Programming Chart
inside the back cover of this manual, then scan Save. Scan the Reset bar code and wait for the scanner to relink to the base.
Scanner Name
Application Work Groups
Your cordless system can have up to 7 scanners linked to one base or Access Point. You can also have up to 7 work groups. If
you want to have all of the scanners’ settings programmed alike, you don’t need to use more than 1 work group. If you want
each scanner to have unique settings (e.g., beeper volume, prefix/suffix, data formatter), then you may program each scanner to
its own unique work group and may program each scanner independently. For example, you might want to have multiple work
groups in a retail/warehouse application where you need to have different data appended to bar codes used in the warehouse
area versus the retail area. You could assign all the scanners in the retail area to one work group and those in the warehouse to
another. Consequently, any desired changes to either the retail or warehouse area would apply to all scanners in that particular
work group. Honeywell’s online configuration tool, EZConfig-Scanning (page 9-2), makes it easy for you to program your system for use with multiple scanners and multiple work groups.
The scanner keeps a copy of the menu settings it is using. Whenever the scanner is connected or reconnected to a base or an
Access Point, the scanner is updated with the latest settings from the base or Access Point for its work group. The scanner also
receives menu setting changes processed by the base or Access Point. If a scanner is removed from a base or an Access Point
and placed into another base or linked to another Access Point, it will be updated with the new base/Access Point settings for
whatever work group to which that the scanner was previously assigned. For example, if the scanner was in work group 1 linked
to the first base, it will be placed in work group 1 in the second base with the associated settings.
3 - 19
Application Work Group Selection
This programming selection allows you to assign a scanner to a work group by scanning the bar code below. You may then
program the settings (e.g., beeper volume, prefix/suffix, data formatter) that your application requires. Default = Group 0.
* Group 0
Group 1
Group 2
Group 3
Group 4
Group 5
Group 6
Resetting the Factory Defaults: All Application Work Groups
The following bar code defaults all of the work groups to the factory default settings.
PAPDFT&
Factory Default Settings:
All Work Groups
To see what the factory default settings are, refer to the table of Menu Commands, beginning on page 10-3. The standard product default settings for each of the commands are indicated by an asterisk (*).
Note: Scanning this bar code also causes both the scanner and the base or Access Point to perform a reset and become
unlinked. The scanner must be placed in the base, or the Access Point linking bar code must be scanned to re-establish
the link. Refer to Scanner Modes, page 3-9 for additional information.
If your scanner is in multiple scanner mode, you will hear up to 30 seconds of beeping while all scanners are relinked to
the base or Access Point and the settings are changed.
3 - 20
Resetting the Custom Defaults: All Application Work Groups
If you want the custom default settings restored to all of the work groups, scan the Custom Product Default Settings bar code
below. (If there are no custom defaults, it will reset the work groups to the factory defaults.) See "Setting Custom Defaults" on
page 1-7 for further information about custom defaults.
Custom Default Settings:
All Work Groups
Note: Scanning this bar code also causes both the scanner and the base or Access Point to perform a reset and become
unlinked. The scanner must be placed in its base, or the Access Point linking bar code must be scanned to re-establish
the link. Refer to Scanner Modes, page 3-9 for additional information.
If your scanner is in multiple scanner mode, you will hear up to 30 seconds of beeping while all scanners are relinked to
the base or Access Point and the settings are changed.
Using the Scanner with Bluetooth Devices
The scanner can be used either with the charge base, an Access Point, or with other Bluetooth devices. Those devices include
personal computers, laptops, PDAs, and Honeywell mobility systems devices.
Bluetooth HID Keyboard Connect
Your scanner can be paired with Bluetooth-capable devices, such as iPads, smart phones, and laptops, so that scanned
data appears on your device screen as though it was entered on the keyboard. In order to pair with the Bluetooth device:
1. Scan the Bluetooth HID Keyboard Connect bar code below.
Bluetooth HID Keyboard
Connect
2. Set the Bluetooth-capable host device so it searches for other Bluetooth devices. (Refer to your device’s User’s Guide
for pairing instructions.)
3. Once your host device has located the scanner, select the scanner name. The host generates and displays a random
PIN that must be scanned within 60 seconds. You must quickly scan Bluetooth PIN Code, then the numbers below,
then Save.
Bluetooth PIN Code
0
1
3 - 21
2
3
4
5
6
7
8
9
Save
Virtual Keyboard
Once your scanner has been connected directly to an iPad, smart phone, or laptop, you can toggle the virtual keyboard on
your device with a quick double pull of the scanner trigger.
3 - 22
Bluetooth HID Keyboard Disconnect
If your scanner has been connected directly to an iPad, smart phone, or laptop using Bluetooth HID Keyboard Connect
(page 3-21), you must disconnect it in order to once again communicate with the base or Access Point. Scan the Bluetooth HID Keyboard Disconnect bar code to unlink the scanner from the currently linked host. Scan the linking bar code
on the base or Access Point to relink the scanner.
Bluetooth HID Keyboard Disconnect
Bluetooth Serial Port - PCs/Laptops
Scanning the Non-Base BT Connection bar code below allows the scanner to be used with other Bluetooth devices (e.g.,
PC/laptop). When in this mode, the scanner behaves like an RS-232 serial device, and you will need to open a COM port
on the host to read scanned data.
After you scan the bar code below, follow the instructions supplied with your Bluetooth device to locate the scanner and
connect to it. If you go out of range with your scanner, the scanner will not reconnect to the Bluetooth device when it is back
in range. If you want to relink to the charge base or Access Point, refer to Override Locked Scanner, page 3-10.
Note: The multiple work groups option is not available when you are using the scanner with Bluetooth devices other than
the charge base or Access Point.
Non-Base BT Connection
PDAs/Mobility Systems Devices
You may also use the scanner with a PDA or a Honeywell Mobility Systems device. Scan the bar code below and follow the
instructions supplied with your Bluetooth device to locate the scanner, and connect with it.
BT Connection - PDA/Mobility Systems Device
Changing the Scanner’s Bluetooth PIN Code
Some devices require a PIN code as part of the Bluetooth security features. Your scanner’s default PIN is 1234, which you
may need to enter the first time you connect to your PDA or PC. The PIN code must be between 1 and 16 characters. To
change the PIN, scan the bar code below and then scan the appropriate numeric bar codes from the Programming Chart
inside the back cover of this manual. Scan Save to save your selection.
Bluetooth PIN
Minimizing Bluetooth/ISM Band Network Activity
The settings described below can help you customize the relinking behavior of the cordless area-imaging system to obtain the
best compromise between convenience and low interference.
Note: ISM band refers to the 2.4 to 2.48 GHz frequency band used by wireless networks, cordless phones, and Bluetooth.
3 - 23
Auto Reconnect Mode
Auto Reconnect controls whether or not the scanner automatically begins the relink process when a loss of connection is
detected. When the Auto Reconnect On bar code is scanned, the scanner begins the relink process immediately, without
user intervention. Default = Auto Reconnect On.
* Auto Reconnect On
Auto Reconnect Off
Note: If you are connecting to a Bluetooth Interface Module, set Auto Reconnect to Off.
The table below shows the results of the Auto Reconnect On and Off settings:
Event
Auto Reconnect On
Auto Reconnect Off
Scanner out of range
Relink occurs automatically. If maximum
number of link attempts is unsuccessful,
then the scanner must be relinked by
either pulling the trigger, placing the
scanner in the base, or scanning the
Access Point linking bar code. (See
"Maximum Link Attempts" on page 3-24.)
The scanner is relinked by pulling the
trigger, or scanning the Access Point
linking bar code.
Base or Access point reset
(firmware upgrade or power cycle)
Scanner behaves as if out of range.
No attempt to relink made while base
or Access Point is powered off.
Trigger must be pulled to initiate
relinking.
Scanner power down due to
Power Time-Out Timer setting
(see page 3-11)
Trigger must be pulled, Access Point linking bar code must be scanned, or the
scanner must be placed in the base unit to relink.
(Note: scanner relinks on power up, but powers on due to one of the above
actions.)
Scanner reset due to firmware
upgrade
Relink occurs automatically.
Scanner reset due to battery
change
Relink occurs automatically.
Scanner placed in different base
unit
Relink to new base occurs automatically.
Maximum Link Attempts
The Maximum Link Attempts setting controls the number of times the scanner tries to form a connection with a base or an
Access Point. During the connection setup process, the scanner transmits in order to search for and connect to a base or
an Access Point. In order to prevent continuous transmissions that could interfere with other users of the ISM band, the
number of attempts to connect is limited by this setting. After the maximum number of attempts is reached, the scanner will
not attempt to reconnect to a base or an Access Point. Pressing the trigger, scanning an Access Point linking bar code, or
placing the scanner in the cradle resets the attempt count and the scanner will again try to link.
3 - 24
Scan the Maximum Link Attempts bar code, then scan the number of attempts for the setting (from 0-100) from the inside
back cover. Scan Save to save the setting. Default = 0.
Maximum Link Attempts
Note: When Auto Reconnect Mode is On, setting Maximum Link Attempts to zero will cause the scanner to try to link until
the Power Time-Out Timer setting (see page 3-11) expires. When Auto Reconnect Mode is Off, setting Maximum
Link Attempts to zero will cause the scanner to only attempt linking one time after a trigger pull.
Relink Time-Out
Relink Time-Out controls the idle time between relink attempts. An attempt to link a scanner to a base or an Access Point
typically lasts up to 5 seconds. This is the time when the scanner is actually attempting a contact . Relink Time-Out controls the amount of time, in seconds, that elapses between the end of one connection attempt and the start of the next.
Note: The length of time for an attempt depends on the number of scanners connected to a base unit or Access Point. An
extra 7 seconds may be required when a connection is successful.
Scan the Relink Time-Out bar code, then scan the number of seconds for the setting (from 1-100) from the inside back
cover. Scan Save to save the setting. Default = 3 seconds.
Relink Time-Out
Bluetooth/ISM Network Activity Examples
Default values
When the scanner goes out of range, the scanner repeatedly attempts to connect to the base unit or Access Point. Each
attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After one hour, the scanner
powers off and batch mode data is lost.
Maximum Link Attempts set to 15
Other values at default setting
When the scanner goes out of range, 15 attempts are made to link to the base unit or Access Point. Each attempt consists
of approximately 5 seconds of active time followed by 3 seconds of idle time. After 15 cycles (8*15 =120), or about 2 minutes, the scanner stops trying to connect to the base or Access Point, but retains any bar codes that may have been saved
in batch mode. After one hour, the scanner powers off and batch mode data is lost.
Auto Reconnect Mode set to 0
Maximum Link Attempts set to 15
Other values at default setting
When the scanner goes out of range, no action is taken to relink. When the trigger is pulled, 15 attempts are made to link
to the base or Access Point. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle
time. After 15 cycles (8*15 =120), or about 2 minutes, the scanner stops trying to connect to the base or Access Point, but
retains any bar codes that may have been saved in batch mode. After one hour, the scanner powers off and batch mode
data is lost. Refer to Auto Reconnect Mode, page 3-24, to review other events that can start the relink process.
Auto Reconnect Mode set to 1
Maximum Link Attempts set to 0
Relink Time-Out set to 10
Scanner Power Time-Out Timer set to 1800
Note: See Scanner Power Time-Out Timer on page 3-11.
The scanner attempts to connect to the base or Access Point every 15 seconds, measured from one attempt start to the
next attempt start. After one half hour, the scanner powers off.
3 - 25
Host Acknowledgment
Some applications require that the host terminal (or server) validate incoming bar code data (database look-up) and provide
acknowledgment to the scanner whether or not to proceed. In Host ACK Mode, the scanner waits for this acknowledgment after
each scan. Visual and audible acknowledgments provide valuable feedback to the scan operator. The Host ACK functionality is
controlled via a number of pre-defined escape commands that are sent to the scanner to make it behave in different ways.
Note: System performance degrades when using Host ACK at rates lower than 9600 baud.
The following criteria must be met for the Host ACK to work correctly:
•
•
•
•
•
The cordless system must be configured for Host Port RS232 (terminal ID = 000) or USB COM Emulation (terminal ID = 130).
RTS/CTS is defaulted off. You must enable it if the host system requires it.
Host ACK must be set to On (page 3-27).
A comma must be used as a terminator.
The host terminal software must be capable of interpreting the bar code data, make decisions based on the data content, and
send out appropriate escape commands to the scanner.
Escape commands are addressed to the scanner via “Application Work Groups.” Once a command is sent, all scanners in a
group respond to that command. Because of this, it is recommended that each scanner is assigned to its own group in
Host ACK mode.
The commands to which the scanner responds are listed on page 3-27. The [ESC] is a 1B in hex. A typical command string is
y [ESC] x, where “y” is the application work group number, “[ESC] x” is the escape command, and the comma is the terminator,
which is required. (When “y” is not specified, the command is sent to the default Application Work Group 0.)
Example: Commands may be strung together to create custom response sequences. An example of a command string is listed
below.
0[ESC]4,[ESC]5,[ESC]6,
The above example will make a scanner that is in application work group zero beep low, then medium, then high.
Example: A good read beep is required for any item on file, but a razz or error tone is required if the item is not on file. In this
case,
[ESC]7, is sent to the host for an on-file product
[ESC]8,[ESC]8, is sent to the host for a not-on-file product
When a bar code is scanned, the scanner enters a timeout period until either the host ACK sequence is received, or the timeout
expires (in 10 seconds, by default).
Once Host ACK is enabled, the system works as follows when a bar code is scanned:
• The scanner reads the code and sends data to the base or Access Point to transmit to the host system. No audible or visual
indication is emitted until the scanner receives an escape command. The scanner read illumination goes out when there’s a
successful read.
• Scanner operation is suspended until 1) a valid escape string is received from the host system or 2) the scanner times out.
• Once condition 1 or 2 above has been met, the scanner is ready to scan again, and the process repeats.
A time-out occurs if the scanner does not receive a valid escape command within 10 seconds. A time-out is indicated by an
error tone. If a time-out occurs, the operator should check the host system to understand why a response to the scanner was
not received.
3 - 26
Host ACK On/Off
Host ACK On
* Host ACK Off
Host ACK Responses
Command
Action
[ESC] a,
Double beeps to indicate a successful menu change was made.
[ESC] b,
Razz or error tone to indicate a menu change was unsuccessful.
[ESC] 1,
The green LED illuminates for 135 milliseconds followed by a pause.
[ESC] 2,
The green LED illuminates for 2 seconds followed by a pause.
[ESC] 3,
The green LED illuminates for 5 seconds followed by a pause.
[ESC] 4,
Emits a beep at a low pitch.
[ESC] 5,
Emits a beep at a medium pitch.
[ESC] 6,
Emits a beep at a high pitch.
[ESC] 7,
Beeps to indicate a successful decode and communication to host.
[ESC] 8,[ESC] 8,
Razz or error tone to indicate a decode/communication to host was unsuccessful.
3 - 27
3 - 28
4
Input/Output Settings
Power Up Beeper
The scanner can be programmed to beep when it’s powered up. If you are using a cordless system, the base can also be programmed to beep when it is powered up. Scan the Off bar code(s) if you don’t want a power up beep. Default = Power Up
Beeper On - Scanner.
Power Up Beeper Off Scanner
* Power Up Beeper On Scanner
Power Up Beeper Off Cordless Base
* Power Up Beeper On Cordless Base
Beep on BEL Character
You may wish to force the scanner to beep upon a command sent from the host. If you scan the Beep on BEL On bar code
below, the scanner will beep every time a BEL character is received from the host. Default = Beep on BEL Off.
*Beep on BEL Off
Beep on BEL On
Trigger Click
To hear an audible click every time the scanner trigger is pressed, scan the Trigger Click On bar code below. Scan the Trigger
Click Off code if you don’t wish to hear the click. (This feature has no effect on serial or automatic triggering.) Default = Trigger
Click Off.
*Trigger Click Off
4-1
Trigger Click On
Good Read and Error Indicators
Beeper – Good Read
The beeper may be programmed On or Off in response to a good read. Turning this option off, only turns off the beeper
response to a good read indication. All error and menu beeps are still audible. Default = Beeper - Good Read On.
Beeper - Good Read Off
* Beeper - Good Read On
Beeper Volume – Good Read
The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High.
Low
Medium
* High
Off
Beeper Pitch – Good Read
The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read. Default = Medium.
Low (1600 Hz)
4-2
* Medium (2400 Hz)
High (4200 Hz)
Beeper Pitch – Error
The beeper pitch codes modify the pitch (frequency) of the sound the scanner emits when there is a bad read or error.
Default = Razz.
* Razz (250 Hz)
Medium (3250 Hz)
High (4200 Hz)
Beeper Duration – Good Read
The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal.
* Normal Beep
Short Beep
LED – Good Read
The LED indicator can be programmed On or Off in response to a good read. Default = On.
* LED - Good Read On
LED - Good Read Off
4-3
Number of Beeps – Good Read
The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the
beeper and LED in response to a good read. For example, if you program this option to have five beeps, there will be five
beeps and five LED flashes in response to a good read. The beeps and LED flashes are in sync with one another. To
change the number of beeps, scan the bar code below and then scan a digit (1-9) bar code and the Save bar code on the
Programming Chart inside the back cover of this manual. Default = 1.
Number of Good Read Beeps/LED Flashes
Number of Beeps – Error
The number of beeps and LED flashes emitted by the scanner for a bad read or error can be programmed from 1 - 9. For
example, if you program this option to have five error beeps, there will be five error beeps and five LED flashes in response
to an error. To change the number of error beeps, scan the bar code below and then scan a digit (1-9) bar code and the
Save bar code on the Programming Chart inside the back cover of this manual. Default = 1.
Number of Error Beeps/LED Flashes
Good Read Delay
This sets the minimum amount of time before the scanner can read another bar code. Default = 0 ms (No Delay).
* No Delay
Short Delay (500 ms)
Medium Delay (1,000 ms)
Long Delay (1,500 ms)
User-Specified Good Read Delay
If you want to set your own length for the good read delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the inside back cover, then scanning Save.
User-Specified Good Read Delay
4-4
Manual Trigger Mode
When in manual trigger mode, the scanner scans until a bar code is read, or until the trigger is released. Default = Manual Trigger-Normal.
* Manual Trigger - Normal
LED Illumination - Manual Trigger
If you wish to set the illumination LED brightness, scan one of the bar codes below. This sets the LED illumination for the
scanner when the trigger is pressed. Default = High.
Note: The LEDs are like a flash on a camera. The lower the ambient light in the room, the brighter the LEDs need to be so
the scanner can “see” the bar codes.
Low
Medium
Medium High
* High
Serial Trigger Mode
You can activate the scanner either by pressing the trigger, or using a serial trigger command (see Trigger Commands on page
10-3). When in serial mode, the scanner scans until a bar code has been read or until the deactivate command is sent. The
scanner can also be set to turn itself off after a specified time has elapsed (see Read Time-Out, which follows).
Read Time-Out
Use this selection to set a time-out (in milliseconds) of the scanner’s trigger when using serial commands to trigger the
scanner. Once the scanner has timed out, you can activate the scanner either by pressing the trigger or using a serial trigger command. After scanning the Read Time-Out bar code, set the time-out duration (from 0-300,000 milliseconds) by
scanning digits on the Programming Chart inside the back cover, then scanning Save. Default = 30,000 ms.
Read Time-Out
4-5
Presentation Mode
Presentation Mode uses ambient light to detect bar codes. The LED dims until a bar code is presented to the scanner, then the
LED brightens to read the code. If the light level in the room is not high enough, Presentation Mode may not work properly.
Note: If you are using a cordless charge base in Presentation Mode, the battery will not charge unless the power supply is
plugged into the base’s auxiliary power port.
Scan the following bar code to program your scanner for Presentation Mode.
Presentation Mode
Idle Illumination - Presentation Mode
Scan one of the bar codes below to set the LED illumination for the scanner when it is in an idle state in Presentation Mode.
Default = High.
Note: If you use one of the lower Idle Illumination settings, and there is not enough ambient light, the scanner may have
difficulty detecting when a bar code is presented to it. If the scanner has difficulty “waking up” to read bar codes, you
may need to set the Idle Illumination to a brighter setting.
Low
Medium
* High
Presentation Sensitivity
Presentation Sensitivity is a numeric range that increases or decreases the scanner's reaction time to bar code presentation. To set the sensitivity, scan the Sensitivity bar code, then scan the degree of sensitivity (from 0-20) from the inside
back cover, and Save. 0 is the most sensitive setting, and 20 is the least sensitive. Default = 1.
Sensitivity
Presentation Centering
Use Presentation Centering to narrow the scanner’s field of view when it is in the stand to make sure the scanner reads
only those bar codes intended by the user. For instance, if multiple codes are placed closely together, Presentation Centering will insure that only the desired codes are read.
Note: To adjust centering when the scanner is hand-held, see Centering (page 4-14).
If a bar code is not touched by a predefined window, it will not be decoded or output by the scanner. If Presentation Centering is turned on by scanning Presentation Centering On, the scanner only reads codes that pass through the centering
window you specify using the Top of Presentation Centering Window, Bottom of Presentation Centering Window,
Left, and Right of Presentation Centering Window bar codes.
4-6
In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right,
8% top, and 25% bottom. Since Bar Code 1 passes through the centering window, it will be read. Bar Code 2 does not
pass through the centering window, so it will not be read.
0%
Bar Code 1
10
Bar Code 2
20
30
40
50
60
70
80
90
100
0
10
20
30
40
50
60
70
80
90
100%
Note: A bar code needs only to be touched by the centering window in order to be read. It does not need to pass completely
through the centering window.
Scan Presentation Centering On, then scan one of the following bar codes to change the top, bottom, left, or right of the
centering window. Then scan the percent you want to shift the centering window using digits on the inside back cover of
this manual. Scan Save. Default Presentation Centering = 40% for Top and Left, 60% for Bottom and Right.
Presentation Centering On
* Presentation Centering Off
Top of Presentation Centering
Window
Bottom of Presentation
Centering Window
4-7
Left of
Presentation Centering
Window
Right of Presentation Centering
Window
In-Stand Sensor Mode
This feature senses when the scanner is removed from the stand and tells it to begin manual triggering. When Sensor On is
enabled, the scanner defaults to Presentation Mode when it is in the stand, and to Manual Trigger Mode when it is removed from
the stand. Default = Sensor On.
* Sensor On
Sensor Off
Poor Quality Codes
Poor Quality 1D Codes
This setting improves the scanner’s ability to read damaged or badly printed linear bar codes. When Poor Quality 1D
Reading On is scanned, poor quality linear bar code reading is improved, but the scanner’s snappiness is decreased, making it less aggressive when reading good quality bar codes. This setting does not affect 2D bar code reading. Default =
Poor Quality 1D Reading Off.
Poor Quality 1D Reading On
* Poor Quality 1D Reading Off
4-8
Poor Quality PDF Codes
This setting improves the scanner’s ability to read damaged or badly printed PDF codes by combining information from multiple images. When Poor Quality PDF On is scanned, poor quality PDF code reading is improved, but the scanner’s snappiness is decreased, making it less aggressive when reading good quality bar codes. This setting does not affect 1D bar
code reading. Default = Poor Quality PDF Reading Off.
Poor Quality PDF Reading On
* Poor Quality PDF Reading Off
CodeGate®
When CodeGate is On, the trigger is used to allow decoded data to be transmitted to the host system. The scanner remains on,
scanning and decoding bar codes, but the bar code data is not transmitted until the trigger is pressed. When CodeGate is Off,
bar code data is transmitted when it is decoded. Default = CodeGate Off Out-of-Stand.
* CodeGate Off
Out-of-Stand
CodeGate On
Out-of-Stand
Mobile Phone Read Mode
When this mode is selected, your scanner is optimized to read bar codes from mobile phone or other LED displays. However,
the speed of scanning printed bar codes may be slightly lower when this mode is enabled.
Hand Held Scanning - Mobile
Phone
Note: To turn off Mobil Phone Read Mode, scan the Manual Trigger Mode bar code (see page 4-5).
Hands Free Time-Out
The Scan Stand and Presentation Modes are referred to as “hands free” modes. If the scanner’s trigger is pressed when using
a hands free mode, the scanner changes to manual trigger mode. You can set the time the scanner should remain in manual
trigger mode by setting the Hands Free Time-Out. Once the time-out value is reached, (if there have been no further trigger
presses) the scanner reverts to the original hands free mode.
4-9
Scan the Hands Free Time-Out bar code, then scan the time-out duration (from 0-300,000 milliseconds) from the inside back
cover, and Save. Default = 5,000 ms.
Hands Free Time-Out
Reread Delay
This sets the time period before the scanner can read the same bar code a second time. Setting a reread delay protects against
accidental rereads of the same bar code. Longer delays are effective in minimizing accidental rereads. Use shorter delays in
applications where repetitive bar code scanning is required. Reread Delay only works when in Presentation Mode (see page 46). Default = Medium.
Short (500 ms)
* Medium (750 ms)
Long (1000 ms)
Extra Long (2000 ms)
User-Specified Reread Delay
If you want to set your own length for the reread delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds)
by scanning digits from the inside back cover, then scanning Save.
User-Specified Reread Delay
2D Reread Delay
Sometimes 2D bar codes can take longer to read than other bar codes. If you wish to set a separate Reread Delay for 2D
bar codes, scan one of the programming codes that follows. 2D Reread Delay Off indicates that the time set for Reread
Delay is used for both 1D and 2D bar codes. Default = 2D Reread Delay Off.
* 2D Reread Delay Off
4 - 10
Short (1000ms)
Medium (2000ms)
Long (3000ms)
Extra Long (4000ms)
Character Activation Mode
You may use a character sent from the host to trigger the scanner to begin scanning. When the activation character is received,
the scanner continues scanning until either the Character Activation Laser Timeout (page 4-12), the deactivation character is
received (see Deactivation Character on page 4-12), or a bar code is transmitted. Scan the following On bar code to use character activation, then use Activation Character (following) to select the character you will send from the host to start scanning.
Default = Off.
* Off
On
Activation Character
This sets the character used to trigger scanning when using Character Activation Mode. On the ASCII Conversion Chart
(Code Page 1252), page A-3, find the hex value that represents the character you want to use to trigger scanning. Scan
the following bar code, then use the Programming Chart to read the alphanumeric combination that represents that ASCII
character. Scan Save to finish.
Activation Character
4 - 11
End Character Activation After Good Read
After a bar code is successfully detected and read from the scanner, the laser can be programmed either to remain on and
scanning, or to turn off. When End Character Activation After Good Read is enabled, the laser turns off and stops scanning after a good read. If you scan Do Not End Character Activation After Good Read, the laser remains on after a good
read. Default = End Character Activation After Good Read.
Do Not End Character Activation
After Good Read
* End Character Activation After
Good Read
Character Activation Laser Timeout
You can set a timeout for the length of time the laser remains on and attempting to decode bar codes when using Character
Activation Mode. Set the length (in milliseconds) for a timeout by scanning the following bar code, then setting the timeout
(from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 5000 ms.
Character Activation Laser
Timeout
Character Deactivation Mode
If you have sent a character from the host to trigger the scanner to begin scanning, you can also send a deactivation character
to stop scanning. Scan the following On bar code to use character deactivation, then use Deactivation Character (following) to
select the character you will send from the host to terminate scanning. Default = Off.
* Off
On
Deactivation Character
This sets the character used to terminate scanning when using Character Deactivation Mode. On the ASCII Conversion
Chart (Code Page 1252), page A-3, find the hex value that represents the character you want to use to terminate scanning.
Scan the following bar code, then use the Programming Chart to read the alphanumeric combination that represents that
ASCII character. Scan Save to finish.
Deactivation Character
4 - 12
Illumination Lights
If you want the illumination lights on while reading a bar code, scan the Lights On bar code, below. However, if you want to turn
just the lights off, scan the Lights Off bar code. Default = Lights On.
Note: This setting does not affect the aimer light. The aiming light can be set using Aimer Mode (below).
* Lights On
Lights Off
Aimer Delay
The aimer delay allows a delay time for the operator to aim the scanner before the picture is taken. Use these codes to set the
time between when the trigger is pulled and when the picture is taken. During the delay time, the aiming light will appear, but
the LEDs won’t turn on until the delay time is over. Default = Off.
200 milliseconds
400 milliseconds
* Off (no delay)
User-Specified Aimer Delay
If you want to set your own length for the duration of the delay, scan the bar code below, then set the time-out by scanning
digits (0 - 4,000 ms) from the Programming Chart inside the back cover of this manual, then scan Save.
Delay Duration
Aimer Mode
This feature allows you to turn the aimer on and off. When the Interlaced bar code is scanned, the aimer is interlaced with the
illumination LEDs. Default = Interlaced.
Off
4 - 13
* Interlaced
Centering
Use Centering to narrow the scanner’s field of view to make sure that when the scanner is hand-held, it reads only those bar
codes intended by the user. For instance, if multiple codes are placed closely together, centering will insure that only the
desired codes are read.
Note: To adjust centering when the scanner is in the stand, see Presentation Centering (page 4-6).
If a bar code is not touched by a predefined window, it will not be decoded or output by the scanner. If centering is turned on by
scanning Centering On, the scanner only reads codes that pass through the centering window you specify using the Top of
Centering Window, Bottom of Centering Window, Left, and Right of Centering Window bar codes.
In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top,
and 25% bottom. Since Bar Code 1 passes through the centering window, it will be read. Bar Code 2 does not pass through
the centering window, so it will not be read.
0%
Bar Code 1
10
Bar Code 2
20
30
40
50
60
70
80
90
100
0
10
20
30
40
50
60
70
80
90
100%
Note: A bar code needs only to be touched by the centering window in order to be read. It does not need to pass completely
through the centering window.
Scan Centering On, then scan one of the following bar codes to change the top, bottom, left, or right of the centering window.
Then scan the percent you want to shift the centering window using digits on the inside back cover of this manual. Scan Save.
Default Centering = 40% for Top and Left, 60% for Bottom and Right.
Centering On
4 - 14
* Centering Off
Top of Centering Window
Bottom of Centering Window
Left of Centering Window
Right of Centering Window
No Read
With No Read turned On, the scanner notifies you if a code cannot be read. If using an EZConfig-Scanning Tool Scan Data
Window (see page 9-2), an “NR” appears when a code cannot be read. If No Read is turned Off, the “NR” will not appear.
Default = Off.
On
* Off
If you want a different notation than “NR,” for example, “Error,” or “Bad Code,” you can edit the output message (see Data
Formatting beginning on page 6-1). The hex code for the No Read symbol is 9C.
4 - 15
Video Reverse
Video Reverse is used to allow the scanner to read bar codes that are inverted. The Video Reverse Off bar code below is an
example of this type of bar code. Scan Video Reverse Only to read only inverted bar codes. Scan Video Reverse and Standard Bar Codes to read both types of codes.
Note: After scanning Video Reverse Only, menu bar codes cannot be read. You must scan Video Reverse Off or Video
Reverse and Standard Bar Codes in order to read menu bar codes.
Note: Images downloaded from the unit are not reversed. This is a setting for decoding only.
Video Reverse Only
Video Reverse and Standard Bar
Codes
* Video Reverse Off
Working Orientation
Some bar codes are direction-sensitive. For example, KIX codes and OCR can misread when scanned sideways or upside
down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scanner.
Default = Upright.
Upright:
Vertical, Top to Bottom:
(Rotate CW 90°)
Upside Down:
Vertical, Bottom to Top:
(Rotate CCW 90°)
4 - 16
* Upright
Vertical, Bottom to Top
Upside Down
Vertical, Top to Bottom
4 - 17
4 - 18
5
Data Editing
Prefix/Suffix Overview
When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar
code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the
user-defined data into the message string.
Prefix and Suffix characters are data characters that can be sent before and after scanned data. You can specify if they should
be sent with all symbologies, or only with specific symbologies. The following illustration shows the breakdown of a message
string:
Prefix
Scanned Data
1-11
variable length
alpha numeric &
control characters
Suffix
1-11
alpha numeric &
control characters
Points to Keep In Mind
• It is not necessary to build a message string. The selections in this chapter are only used if you wish to alter the default
settings. Default prefix = None. Default suffix = None.
• A prefix or suffix may be added or cleared from one symbology or all symbologies.
• You can add any prefix or suffix from the ASCII Conversion Chart (Code Page 1252), beginning on page A-3, plus Code
I.D. and AIM I.D.
• You can string together several entries for several symbologies at one time.
• Enter prefixes and suffixes in the order in which you want them to appear on the output.
• When setting up for specific symbologies (as opposed to all symbologies), the specific symbology ID value counts as an
added prefix or suffix character.
• The maximum size of a prefix or suffix configuration is 200 characters, which includes header information.
To Add a Prefix or Suffix:
Step 1. Scan the Add Prefix or Add Suffix symbol (page 5-2).
Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Symbology Charts, beginning on page
A-1) for the symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and
Hex ID is “6A”.
Step 3. Scan the 2 hex digits from the Programming Chart inside the back cover of this manual or scan 9, 9 for all
symbologies.
Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page 1252), beginning on page A-3, for the prefix
or suffix you wish to enter.
Step 5. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual.
Step 6. Repeat Steps 4 and 5 for every prefix or suffix character.
Step 7. To add the Code I.D., scan 5, C, 8, 0.
To add AIM I.D., scan 5, C, 8, 1.
To add a backslash (\), scan 5, C, 5, C.
Note: To add a backslash (\) as in Step 7, you must scan 5C twice – once to create the leading backslash and then to create
the backslash itself.
Step 8. Scan Save to exit and save, or scan Discard to exit without saving.
Repeat Steps 1-6 to add a prefix or suffix for another symbology.
5-1
Example: Add a Tab Suffix to All Symbologies
Step 1. Scan Add Suffix.
Step 2. Scan 9, 9 from the Programming Chart inside the back cover of this manual to apply this suffix to all symbologies.
Step 3. Scan 0, 9 from the Programming Chart inside the back cover of this manual. This corresponds with the hex value
for a horizontal tab, shown in the ASCII Conversion Chart (Code Page 1252), beginning on page A-3.
Step 4. Scan Save, or scan Discard to exit without saving.
To Clear One or All Prefixes or Suffixes
You can clear a single prefix or suffix, or clear all prefixes/suffixes for a symbology. If you have been entering prefixes and
suffixes for single symbologies, you can use Clear One Prefix (Suffix) to delete a specific character from a symbology.
When you Clear All Prefixes (Suffixes), all the prefixes or suffixes for a symbology are deleted.
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol.
Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Symbology Charts, beginning on page
A-1) for the symbology from which you want to clear the prefix or suffix.
Step 3. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual or scan 9, 9 for all
symbologies.
Your change is automatically saved.
To Add a Carriage Return Suffix to All Symbologies
Scan the following bar code if you wish to add a carriage return suffix to all symbologies at once. This action first clears all
current suffixes, then programs a carriage return suffix for all symbologies.
Add CR Suffix
All Symbologies
Prefix Selections
Add Prefix
Clear One Prefix
Clear All Prefixes
Suffix Selections
Add Suffix
5-2
Clear One Suffix
Clear All Suffixes
Function Code Transmit
When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function
code to the terminal. Charts of these function codes are provided in Supported Interface Keys starting on page 8-2. When the
scanner is in keyboard wedge mode, the scan code is converted to a key code before it is transmitted. Default = Enable.
* Enable
Disable
Intercharacter, Interfunction, and Intermessage Delays
Some terminals drop information (characters) if data comes through too quickly. Intercharacter, interfunction, and intermessage
delays slow the transmission of data, increasing data integrity.
Intercharacter Delay
An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each
character of scanned data. Scan the Intercharacter Delay bar code below, then scan the number of 5ms delays, and the
Save bar code using the Programming Chart inside the back cover of this manual.
Prefix
Scanned Data
1
2
3
4
Suffix
5
Intercharacter Delay
Intercharacter Delay
To remove this delay, scan the Intercharacter Delay bar code, then set the number of delays to 0. Scan the Save bar code
using the Programming Chart inside the back cover of this manual.
Note: Intercharacter delays are not supported in USB serial emulation.
User Specified Intercharacter Delay
An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed after the transmission of a particular
character of scanned data. Scan the Delay Length bar code below, then scan the number of 5ms delays, and the Save
bar code using the Programming Chart inside the back cover of this manual.
5-3
Next, scan the Character to Trigger Delay bar code, then the 2-digit hex value for a printable character to trigger the delay
(see Lower ASCII Reference Table on page A-4).
Delay Length
Character to Trigger Delay
To remove this delay, scan the Delay Length bar code, and set the number of delays to 0. Scan the Save bar code using
the Programming Chart inside the back cover of this manual.
Interfunction Delay
An interfunction delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each
segment of the message string. Scan the Interfunction Delay bar code below, then scan the number of 5ms delays, and
the Save bar code using the Programming Chart inside the back cover of this manual.
Prefix
STX
1
Scanned Data
HT
2 3 4 5
Suffix
CR
LF
Interfunction Delays
Interfunction Delay
To remove this delay, scan the Interfunction Delay bar code, then set the number of delays to 0. Scan the Save bar code
using the Programming Chart inside the back cover of this manual.
Intermessage Delay
An intermessage delay of up to 5000 milliseconds (in 5ms increments) may be placed between each scan transmission.
Scan the Intermessage Delay bar code below, then scan the number of 5ms delays, and the Save bar code using the
Programming Chart inside the back cover of this manual.
1st Scan Transmission
2nd Scan Transmission
Intermessage Delay
Intermessage Delay
To remove this delay, scan the Intermessage Delay bar code, then set the number of delays to 0. Scan the Save bar code
using the Programming Chart inside the back cover of this manual.
5-4
6
Data Formatting
Data Format Editor Introduction
You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert
characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to
alter the output. Default Data Format setting = None.
Normally, when you scan a bar code, it gets outputted automatically; however when you create a format, you must use a “send”
command (see Send Commands on page 6-3) within the format program to output data.
Multiple formats may be programmed into the scanner. They are stacked in the order in which they are entered. However, the
following list presents the order in which formats are applied:
1.
2.
3.
4.
5.
6.
7.
8.
Specific Terminal ID, Actual Code ID, Actual Length
Specific Terminal ID, Actual Code ID, Universal Length
Specific Terminal ID, Universal Code ID, Actual Length
Specific Terminal ID, Universal Code ID, Universal Length
Universal Terminal ID, Actual Code ID, Actual Length
Universal Terminal ID, Actual Code ID, Universal Length
Universal Terminal ID, Universal Code ID, Actual Length
Universal Terminal ID, Universal Code ID, Universal Length
The maximum size of a data format configuration is 2000 bytes, which includes header information.
If you have changed data format settings, and wish to clear all formats and return to the factory defaults, scan the Default Data
Format code below.
* Default Data Format
Add a Data Format
Step 1. Scan the Enter Data Format symbol (page 6-2).
Step 2. Select Primary/Alternate Format
Determine if this will be your primary data format, or one of 3 alternate formats. This allows you to save a total of 4
different data formats. To program your primary format, scan 0 using the Programming Chart inside the back cover of
this manual. If you are programming an alternate format, scan 1, 2, or 3, depending on which alternate format you are
programming. (See "Primary/Alternate Data Formats" on page 6-9 for further information.)
Step 3. Terminal Type
Refer to Terminal ID Table (page 6-3) and locate the Terminal ID number for your PC. Scan three numeric bar codes
on the inside back cover to program the scanner for your terminal ID (you must enter 3 digits). For example, scan 0 0
3 for an AT wedge.
Note: The wildcard for all terminal types is 099.
Step 4. Code I.D.
In the Symbology Charts, beginning on page A-1, find the symbology to which you want to apply the data format. Locate
the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart inside the back cover of
this manual.
Note: If you are creating a data format for Batch Mode Quantity, use 35 for the Code I.D.
Step 5. Length
Specify what length (up to 9999 characters) of data will be acceptable for this symbology. Scan the four digit data length
6-1
from the Programming Chart inside the back cover of this manual. (Note: 50 characters is entered as 0050. 9999 is a
universal number, indicating all lengths.)
Step 6. Editor Commands
Refer to Data Format Editor Commands (page 6-3). Scan the symbols that represent the command you want to enter.
Step 7. Scan Save to save your data format, or Discard to exit without saving your changes.
Enter Data Format
Save
Discard
Other Programming Selections
Clear One Data Format
This deletes one data format for one symbology. If you are clearing the primary format, scan 0 from the Programming
Chart inside the back cover of this manual. If you are clearing an alternate format, scan 1, 2, or 3, depending on the
format you are clearing. Scan the Terminal Type and Code I.D. (see Symbology Charts on page A-1), and the bar code
data length for the specific data format that you want to delete. All other formats remain unaffected.
Clear all Data Formats
This clears all data formats.
Save to exit and save your data format changes.
Discard to exit without saving any data format changes.
Clear One Data Format
Clear All Data Formats
Save
Discard
6-2
Terminal ID Table
Terminal
USB
Serial
Keyboard
Model(s)
PC keyboard (HID)
Mac Keyboard
PC Keyboard (Japanese)
Serial (COM driver required)
HID POS
USB SurePOS Handheld
USB SurePOS Tabletop
RS232 TTL
RS232 True
PS2 compatibles
Terminal ID
124
125
134
130
131
128
129
000
000
003
Data Format Editor Commands
Send Commands
Send all characters
F1 Include in the output message all of the characters from the input message, starting from current cursor position,
followed by an insert character. Syntax = F1xx where xx stands for the insert character’s hex value for its ASCII code.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
Send a number of characters
F2 Include in the output message a number of characters followed by an insert character. Start from the current cursor
position and continue for “nn” characters or through the last character in the input message, followed by character “xx.”
Syntax = F2nnxx where nn stands for the numeric value (00-99) for the number of characters, and xx stands for the the
insert character’s hex value for its ASCII code.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
F2 Example: Send a number of characters
Send the first 10 characters from the bar code above, followed by a carriage return. Command string: F2100D
F2 is the “Send a number of characters” command
10 is the number of characters to send
0D is the hex value for a CR
The data is output as: 1234567890
F2 and F1 Example: Split characters into 2 lines
Send the first 10 characters from the bar code above, followed by a carriage return, followed by the rest of the characters.
Command string: F2100DF10D
F2 is the “Send a number of characters” command
10 is the number of characters to send for the first line
0D is the hex value for a CR
F1 is the “Send all characters” command
0D is the hex value for a CR
6-3
The data is output as:
1234567890
ABCDEFGHIJ
Send all characters up to a particular character
F3 Include in the output message all characters from the input message, starting with the character at the current cursor
position and continuing to, but not including, the search character “ss,” followed by an insert character. The cursor is
moved forward to the “ss” character. Syntax = F3ssxx where ss stands for the search character’s hex value for its ASCII
code, and xx stands for the insert character’s hex value for its ASCII code.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
F3 Example: Send all characters up to a particular character
Using the bar code above, send all characters up to but not including “D,” followed by a carriage return.
Command string: F3440D
F3 is the “Send all characters up to a particular character” command
44 is the hex value for a 'D”
0D is the hex value for a CR
The data is output as:
1234567890ABC
Send all but the last characters
E9 Include in the output message all but the last “nn” characters, starting from the current cursor position. The cursor is
moved forward to one position past the last input message character included. Syntax = E9nn where nn stands for the
numeric value (00-99) for the number of characters that will not be sent at the end of the message.
Insert a character multiple times
F4 Send “xx” character “nn” times in the output message, leaving the cursor in the current position. Syntax = F4xxnn where
xx stands for the insert character’s hex value for its ASCII code, and nn is the numeric value (00-99) for the number of
times it should be sent.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
E9 and F4 Example: Send all but the last characters, followed by 2 tabs
Send all characters except for the last 8 from the bar code above, followed by 2 tabs.
Command string: E908F40902
E9 is the “Send all but the last characters” command
08 is the number of characters at the end to ignore
F4 is the “Insert a character multiple times” command
09 is the hex value for a horizontal tab
02 is the number of times the tab character is sent
The data is output as: 1234567890AB
Move Commands
Move the cursor forward a number of characters
F5 Move the cursor ahead “nn” characters from current cursor position.
Syntax = F5nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved ahead.
6-4
F5 Example: Move the cursor forward and send the data
Move the cursor forward 3 characters, then send the rest of the bar code data from the bar code above. End with a
carriage return.
Command string: F503F10D
F5 is the “Move the cursor forward a number of characters” command
03 is the number of characters to move the cursor
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as:
4567890ABCDEFGHIJ
Move the cursor backward a number of characters
F6 Move the cursor back “nn” characters from current cursor position.
Syntax = F6nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved back.
Move the cursor to the beginning
F7 Move the cursor to the first character in the input message. Syntax = F7.
FE and F7 Example: Manipulate bar codes that begin with a 1
Search for bar codes that begin with a 1. If a bar code matches, move the cursor back to the beginning of the data and
send 6 characters followed by a carriage return. Using the bar code above:
Command string: FE31F7F2060D
FE is the “Compare characters” command
31 is the hex value for 1
F7 is the “Move the cursor to the beginning” command
F2 is the “Send a number of characters” command
06 is the number of characters to send
0D is the hex value for a CR
The data is output as:
123456
Move the cursor to the end
EA Move the cursor to the last character in the input message. Syntax = EA.
Search Commands
Search forward for a character
F8 Search the input message forward for “xx” character from the current cursor position, leaving the cursor pointing to the
“xx” character. Syntax = F8xx where xx stands for the search character’s hex value for its ASCII code.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
6-5
F8 Example: Send bar code data that starts after a particular character
Search for the letter “D” in bar codes and send all the data that follows, including the “D.” Using the bar code above:
Command string: F844F10D
F8 is the “Search forward for a character” command
44 is the hex value for “D”
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as:
DEFGHIJ
Search backward for a character
F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to
the “xx” character. Syntax = F9xx where xx stands for the search character’s hex value for its ASCII code.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
Search forward for a non-matching character
E6 Search the input message forward for the first non-“xx” character from the current cursor position, leaving the cursor
pointing to the non-“xx” character. Syntax = E6xx where xx stands for the search character’s hex value for its ASCII
code.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
E6 Example: Remove zeroes at the beginning of bar code data
This example shows a bar code that has been zero filled. You may want to ignore the zeroes and send all the data that
follows. E6 searches forward for the first character that is not zero, then sends all the data after, followed by a carriage
return. Using the bar code above:
Command string: E630F10D
E6 is the “Search forward for a non-matching character” command
30 is the hex value for 0
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as:
37692
Search backward for a non-matching character
E7 Search the input message backward for the first non-“xx” character from the current cursor position, leaving the cursor
pointing to the non-“xx” character. Syntax = E7xx where xx stands for the search character’s hex value for its ASCII
code.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
6-6
Miscellaneous Commands
Suppress characters
FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is
advanced by other commands. When the FC command is encountered, the suppress function is terminated. The
cursor is not moved by the FB command.
Syntax = FBnnxxyy . .zz where nn is a count of the number of suppressed characters in the list, and xxyy .. zz is the list
of characters to be suppressed.
FB Example: Remove spaces in bar code data
This example shows a bar code that has spaces in the data. You may want to remove the spaces before sending the
data. Using the bar code above:
Command string: FB0120F10D
FB is the “Suppress characters” command
01 is the number of character types to be suppressed
20 is the hex value for a space
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as:
34567890
Stop suppressing characters
FC Disables suppress filter and clear all suppressed characters. Syntax = FC.
Replace characters
E4 Replaces up to 15 characters in the output message, without moving the cursor. Replacement continues until the E5
command is encountered. Syntax = E4nnxx1xx2yy1yy2...zz1zz2 where nn is the total count of of the number of
characters in the list (characters to be replaced plus replacement characters); xx1 defines characters to be replaced and
xx2 defines replacement characters, continuing through zz1 and zz2.
E4 Example: Replace zeroes with CRs in bar code data
If the bar code has characters that the host application does not want included, you can use the E4 command to
replace those characters with something else. In this example, you will replace the zeroes in the bar code above with
carriage returns.
Command string: E402300DF10D
E4 is the “Replace characters” command
02 is the total count of characters to be replaced, plus the replacement characters (0 is replaced by CR, so total characters = 2)
30 is the hex value for 0
0D is the hex value for a CR (the character that will replace the 0)
F1 is the “Send all characters” command
0D is the hex value for a CR
6-7
The data is output as:
1234
5678
ABC
Stop replacing characters
E5 Terminates character replacement. Syntax = E5.
Compare characters
FE Compare the character in the current cursor position to the character “xx.” If characters are equal, move the cursor
forward one position. Syntax = FExx where xx stands for the comparison character’s hex value for its ASCII code.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
Check for a number
EC Check to make sure there is an ASCII number at the current cursor position. The format is aborted if the character is
not numeric.
EC Example: Only output the data if the bar code begins with a number
If you want only data from bar codes that begin with a number, you can use EC to check for the number.
Command string: ECF10D
EC is the “Check for a number” command
F1 is the “Send all characters” command
0D is the hex value for a CR
If this bar code is read,
the next data format, if there is one, will be used on the data. If there
is no other format, the format fails and the raw data is output as AB1234.
If this bar code is read:
the data is output as:
1234AB
Check for non-numeric character
ED Check to make sure there is a non-numeric ASCII character at the current cursor position. The format is aborted if the
character is numeric.
ED Example: Only output the data if the bar code begins with a letter
If you want only data from bar codes that begin with a letter, you can use ED to check for the letter.
Command string: EDF10D
ED is the “Check for a non-numeric character” command
F1 is the “Send all characters” command
0D is the hex value for a CR
If this bar code is read,
the next data format, if there is one, will be used on this data. If there
is no other format, the format fails and the raw data is output as 1234AB.
If this bar code is read:
AB1234
6-8
the data is output as:
Insert a delay
EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position. Syntax = EFnnnn
where nnnn stands for the delay in 5ms increments, up to 9999. This command can only be used with keyboard
emulation.
Data Formatter
When Data Formatter is turned Off, the bar code data is output to the host as read, including prefixes and suffixes.
Data Formatter Off
You may wish to require the data to conform to a data format you have created and saved. The following settings can be applied
to your data format:
Data Formatter On, Not Required, Keep Prefix/Suffix
Scanned data is modified according to your data format, and prefixes and suffixes are transmitted.
Data Format Required, Keep Prefix/Suffix
Scanned data is modified according to your data format, and prefixes and suffixes are transmitted. Any data that does not
match your data format requirements generates an error tone and the data in that bar code is not transmitted.
Default = Data Formatter On, Not Required, Keep Prefix/Suffix.
* Data Formatter On,
Not Required,
Keep Prefix/Suffix
Data Format Required,
Keep Prefix/Suffix
Primary/Alternate Data Formats
You can save up to four data formats, and switch between these formats. Your primary data format is saved under 0. Your other
three formats are saved under 1, 2, and 3. To set your device to use one of these formats, scan one of the bar codes below.
Primary Data Format
Data Format 1
Data Format 2
6-9
Data Format 3
6 - 10
7
Symbologies
This programming section contains the following menu selections. Refer to Chapter 10 for settings and defaults.
• All Symbologies
• Interleaved 2 of 5
• Aztec Code
• Korea Post
• China Post (Hong Kong 2 of 5)
• Matrix 2 of 5
• Chinese Sensible (Han Xin) Code
• MaxiCode
• Codabar
• MicroPDF417
• Codablock A
• MSI
• Codablock F
• NEC 2 of 5
• Code 11
• Postal Codes - 2D
• Code 128
• Postal Codes - Linear
• Code 32 Pharmaceutical (PARAF)
• PDF417
• Code 39
• GS1 DataBar Omnidirectional
• Code 93
• QR Code
• Data Matrix
• Straight 2 of 5 IATA (two-bar start/stop)
• EAN/JAN-13
• Straight 2 of 5 Industrial (three-bar start/stop)
• EAN/JAN-8
• TCIF Linked Code 39 (TLC39)
• GS1 Composite Codes
• UPC-A
• GS1 DataBar Expanded
• UPC-A
• GS1 DataBar Limited
• UPC-A/EAN-13 with Extended Coupon Code
• GS1 DataBar Omnidirectional
• UPC-E0
• GS1 Emulation
• UPC-E1
• GS1-128
All Symbologies
If you want to decode all the symbologies allowable for your scanner, scan the All Symbologies On code. If on the other hand,
you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular symbology.
All Symbologies On
All Symbologies Off
Note: When All Symbologies On is scanned, 2D Postal Codes are not enabled. 2D Postal Codes must be enabled separately.
Message Length Description
You are able to set the valid reading length of some of the bar code symbologies. If the data length of the scanned bar code
doesn’t match the valid reading length, the scanner will issue an error tone. You may wish to set the same value for minimum
and maximum length to force the scanner to read fixed length bar code data. This helps reduce the chances of a misread.
EXAMPLE:
Decode only those bar codes with a count of 9-20 characters.
Min. length = 09Max. length = 20
7-1
EXAMPLE:
Decode only those bar codes with a count of 15 characters.
Min. length = 15Max. length = 15
For a value other than the minimum and maximum message length defaults, scan the bar codes included in the explanation of
the symbology, then scan the digit value of the message length and Save bar codes on the Programming Chart inside the back
cover of this manual. The minimum and maximum lengths and the defaults are included with the respective symbologies.
Codabar
Codabar On/Off
* On
Off
Codabar Start/Stop Characters
Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/
Stop characters. Default = Don’t Transmit.
Transmit
* Don’t Transmit
Codabar Check Character
Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar bar
codes with Modulo 16 check characters. Default = No Check Character.
No Check Character indicates that the scanner reads and transmits bar code data with or without a check character.
When Check Character is set to Validate and Transmit, the scanner will only read Codabar bar codes printed with a check
character, and will transmit this character at the end of the scanned data.
When Check Character is set to Validate, but Don’t Transmit, the unit will only read Codabar bar codes printed with a
check character, but will not transmit the check character with the scanned data.
* No Check Character
7-2
Validate Modulo 16, but
Don’t Transmit
Validate Modulo 16
and Transmit
Codabar Concatenation
Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having
a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concatenated
into one with the “D” characters omitted.
A 1 2 3 4 D
D 5 6 7 8 A
Select Require to prevent the scanner from decoding a single “D” Codabar symbol without its companion. This selection
has no effect on Codabar symbols without Stop/Start D characters.
On
* Off
Require
Codabar Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60.
Minimum Message Length
Maximum Message Length
7-3
Code 39
< Default All Code 39 Settings >
Code 39 On/Off
* On
Off
Code 39 Start/Stop Characters
Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/
Stop characters. Default = Don’t Transmit.
Transmit
* Don’t Transmit
Code 39 Check Character
No Check Character indicates that the scanner reads and transmits bar code data with or without a check character.
When Check Character is set to Validate, but Don’t Transmit, the unit only reads Code 39 bar codes printed with a check
character, but will not transmit the check character with the scanned data.
When Check Character is set to Validate and Transmit, the scanner only reads Code 39 bar codes printed with a check
character, and will transmit this character at the end of the scanned data. Default = No Check Character.
* No Check Character
Validate, but Don’t Transmit
Validate and Transmit
7-4
Code 39 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 0-48. Minimum Default = 0, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
Code 39 Append
This function allows the scanner to append the data from several Code 39 bar codes together before transmitting them to
the host computer. When the scanner encounters a Code 39 bar code with the append trigger character(s), it buffers Code
39 bar codes until it reads a Code 39 bar code that does not have the append trigger. The data is then transmitted in the
order in which the bar codes were read (FIFO). Default = Off.
On
* Off
Code 32 Pharmaceutical (PARAF)
Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian pharmacies. This symbology is also known as
PARAF.
On
* Off
7-5
Full ASCII
If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single
character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #.
Default = Off.
NUL %U
DLE $P
SP
SPACE 0
0
@
%V
P
P
‘
%W p
+P
SOH $A
DC1 $Q
!
/A
1
1
A
A
Q
Q
a
+A
q
+Q
STX $B
DC2 $R
“
/B
2
2
B
B
R
R
b
+B
r
+R
ETX $C
DC3 $S
#
/C
3
3
C
C
S
S
c
+C
s
+S
EOT $D
DC4 $T
$
/D
4
4
D
D
T
T
d
+D
t
+T
ENQ $E
NAK $U
%
/E
5
5
E
E
U
U
e
+E
u
+U
ACK $F
SYN $V
&
/F
6
6
F
F
V
V
f
+F
v
+V
BEL $G
ETB $W
‘
/G
7
7
G
G
W
W
g
+G
w
+W
BS
$H
CAN $X
(
/H
8
8
H
H
X
X
h
+H
x
+X
HT
$I
EM
$Y
)
/I
9
9
I
I
Y
Y
i
+I
y
+Y
LF
$J
SUB $Z
*
/J
:
/Z
J
J
Z
Z
j
+J
z
+Z
VT
$K
ESC %A
+
/K
;
%F
K
K
[
%K
k
+K
{
%P
FF
$L
FS
%B
,
/L
<
%G L
L
\
%L
l
+L
|
%Q
CR
$M
GS
%C
-
-
=
%H
M
M
]
%M m
+M
}
%R
SO
$N
RS
%D
.
.
>
%I
N
N
^
%N
n
+N
~
%S
SI
$O
US
%E
/
/O
?
%J
O
O
_
%O o
+O
DEL %T
Character pairs /M and /N decode as a minus sign and period respectively.
Character pairs /P through /Y decode as 0 through 9.
Full ASCII On
* Full ASCII Off
Code 39 Code Page
Code pages define the mapping of character codes to characters. If the data received does not display with the proper
characters, it may be because the bar code being scanned was created using a code page that is different from the one the
host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were
created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save bar code from
the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly.
Code 39 Code Page
7-6
Interleaved 2 of 5
< Default All Interleaved 2 of 5 Settings >
Interleaved 2 of 5 On/Off
* On
Off
Check Digit
No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit.
When Check Digit is set to Validate, but Don’t Transmit, the unit only reads Interleaved 2 of 5 bar codes printed with a
check digit, but will not transmit the check digit with the scanned data.
When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 bar codes printed with a
check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit.
* No Check Digit
Validate, but Don’t Transmit
Validate and Transmit
Interleaved 2 of 5 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
7-7
Maximum Message Length
NEC 2 of 5
< Default All NEC 2 of 5 Settings >
NEC 2 of 5 On/Off
* On
Off
Check Digit
No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit.
When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 bar codes printed with a check
digit, but will not transmit the check digit with the scanned data.
When Check Digit is set to Validate and Transmit, the scanner only reads NEC 2 of 5 bar codes printed with a check digit,
and will transmit this digit at the end of the scanned data. Default = No Check Digit.
* No Check Digit
Validate, but Don’t Transmit
Validate and Transmit
7-8
NEC 2 of 5 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
Code 93
< Default All Code 93 Settings >
Code 93 On/Off
* On
Off
Code 93 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
7-9
Code 93 Append
This function allows the scanner to append the data from several Code 93 bar codes together before transmitting them to
the host computer. When this function is enabled, the scanner stores those Code 93 bar codes that start with a space
(excluding the start and stop symbols), and does not immediately transmit the data. The scanner stores the data in the
order in which the bar codes are read, deleting the first space from each. The scanner transmits the appended data when
it reads a Code 93 bar code that starts with a character other than a space. Default = Off.
On
* Off
Code 93 Code Page
Code pages define the mapping of character codes to characters. If the data received does not display with the proper
characters, it may be because the bar code being scanned was created using a code page that is different from the one the
host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were
created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save bar code from
the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly.
Code 93 Code Page
7 - 10
Straight 2 of 5 Industrial (three-bar start/stop)
Straight 2 of 5 Industrial On/Off
On
* Off
Straight 2 of 5 Industrial Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
7 - 11
Straight 2 of 5 IATA (two-bar start/stop)
Straight 2 of 5 IATA On/Off
On
* Off
Straight 2 of 5 IATA Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
7 - 12
Matrix 2 of 5
Matrix 2 of 5 On/Off
On
* Off
Matrix 2 of 5 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
7 - 13
Code 11
Code 11 On/Off
On
* Off
Check Digits Required
This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits.
One Check Digit
* Two Check Digits
Code 11 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
7 - 14
Code 128
Code 128 On/Off
* On
Off
ISBT 128 Concatenation
In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard for communicating critical blood information in a uniform manner. The use of ISBT formats requires a paid license. The ISBT 128 Application Specification
describes 1) the critical data elements for labeling blood products, 2) the current recommendation to use Code 128 due to
its high degree of security and its space-efficient design, 3) a variation of Code 128 that supports concatenation of neighboring symbols, and 4) the standard layout for bar codes on a blood product label. Use the bar codes below to turn concatenation on or off. Default =Off.
On
* Off
Code 128 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
7 - 15
Code 128 Append
This function allows the scanner to append the data from several Code 128 bar codes together before transmitting them to
the host computer. When the scanner encounters a Code 128 bar code with the append trigger character(s), it buffers
Code 128 bar codes until it reads a Code 128 bar code that does not have the append trigger. The data is then transmitted
in the order in which the bar codes were read (FIFO). Default = On.
* On
Off
Code 128 Code Page
Code pages define the mapping of character codes to characters. If the data received does not display with the proper
characters, it may be because the bar code being scanned was created using a code page that is different from the one the
host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were
created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save bar code from
the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly.
Code 128 Code Page
7 - 16
GS1-128
GS1-128 On/Off
* On
Off
GS1-128 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-80. Minimum Default = 1, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
UPC-A
UPC-A On/Off
* On
Off
Note: To convert UPC-A bar codes to EAN-13, see Convert UPC-A to EAN-13 on page 7-23.
7 - 17
UPC-A Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.
Default = On.
* On
Off
UPC-A Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can
be programmed so it will not transmit it. Default = On.
* On
Off
UPC-A Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC-A data.
Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
7 - 18
UPC-A Addenda Required
When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or
5 digit addenda listed on page 7-18. Default = Not Required.
Required
* Not Required
UPC-A Addenda Separator
When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned
off, there is no space. Default = On.
* On
Off
UPC-A/EAN-13 with Extended Coupon Code
Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. When left on the default setting
(Off), the scanner treats Coupon Codes and Extended Coupon Codes as single bar codes.
If you scan the Allow Concatenation code, when the scanner sees the coupon code and the extended coupon code in a single
scan, it transmits both as separate symbologies. Otherwise, it transmits the first coupon code it reads.
If you scan the Require Concatenation code, the scanner must see and read the coupon code and extended coupon code in a
single read to transmit the data. No data is output unless both codes are read. Default = Off.
* Off
Allow Concatenation
Require Concatenation
7 - 19
Coupon GS1 DataBar Output
If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to scan and output only the data from the GS1
DataBar code. Scan the GS1 Output On code below to scan and output only the GS1 DataBar code data. Default = GS1 Output Off.
* GS1 Output Off
GS1 Output On
UPC-E0
UPC-E0 On/Off
Most U.P.C. bar codes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to
read codes that lead with the 1 number system, use UPC-E1 (page 7-22). Default = On.
* UPC-E0 On
UPC-E0 Off
UPC-E0 Expand
UPC-E Expand expands the UPC-E code to the 12 digit, UPC-A format. Default = Off.
On
* Off
7 - 20
UPC-E0 Addenda Required
When Required is scanned, the scanner will only read UPC-E bar codes that have addenda. Default = Not Required.
Required
* Not Required
UPC-E0 Addenda Separator
When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned
Off, there is no space. Default = On.
* On
Off
UPC-E0 Check Digit
Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
* On
Off
UPC-E0 Leading Zero
This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan
Off. Default = On.
* On
Off
7 - 21
UPC-E0 Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
UPC-E1
Most U.P.C. bar codes lead with the 0 number system. For these codes, use UPC-E0 (page 7-20). If you need to read codes
that lead with the 1 number system, use the UPC-E1 On selection. Default = Off.
UPC-E1 On
* UPC-E1 Off
7 - 22
EAN/JAN-13
EAN/JAN-13 On/Off
* On
Off
Convert UPC-A to EAN-13
When UPC-A Converted to EAN-13 is selected, UPC-A bar codes are converted to 13 digit EAN-13 codes by adding a
zero to the front. When Do not Convert UPC-A is selected, UPC-A codes are read as UPC-A.
UPC-A Converted to EAN-13
* Do not Convert UPC-A
EAN/JAN-13 Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.
Default = On.
* On
Off
7 - 23
EAN/JAN-13 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit
Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
EAN/JAN-13 Addenda Required
When Required is scanned, the scanner will only read EAN/JAN-13 bar codes that have addenda. Default = Not Required.
Required
* Not Required
EAN/JAN-13 Addenda Separator
When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned
Off, there is no space. Default = On.
* On
Off
Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon
Code (page 7-19).
7 - 24
ISBN Translate
When On is scanned, EAN-13 Bookland symbols are translated into their equivalent ISBN number format. Default = Off.
On
* Off
EAN/JAN-8
EAN/JAN-8 On/Off
* On
Off
EAN/JAN-8 Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.
Default = On.
* On
Off
7 - 25
EAN/JAN-8 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit
Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
EAN/JAN-8 Addenda Required
When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that have addenda. Default = Not Required.
Required
* Not Required
EAN/JAN-8 Addenda Separator
When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned
Off, there is no space. Default = On.
* On
Off
7 - 26
MSI
MSI On/Off
On
* Off
MSI Check Character
Different types of check characters are used with MSI bar codes. You can program the scanner to read MSI bar codes with
Type 10 check characters. Default = Validate Type 10, but Don’t Transmit.
When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI bar codes printed with
the specified type check character(s), and will transmit the character(s) at the end of the scanned data.
When Check Character is set to Validate Type 10/11, but Don’t Transmit, the unit will only read MSI bar codes printed
with the specified type check character(s), but will not transmit the check character(s) with the scanned data.
* Validate Type 10, but Don’t
Transmit
Validate Type 10 and Transmit
Validate 2 Type 10 Characters,
but Don’t Transmit
Validate 2 Type 10 Characters
and Transmit
Validate Type 11 then Type 10
Character, but Don’t Transmit
7 - 27
Validate Type 11 then
Type 10 Character and Transmit
Disable MSI Check Characters
MSI Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
7 - 28
GS1 DataBar Omnidirectional
< Default All GS1 DataBar Omnidirectional Settings >
GS1 DataBar Omnidirectional On/Off
* On
Off
GS1 DataBar Limited
< Default All GS1 DataBar Limited Settings >
GS1 DataBar Limited On/Off
* On
Off
7 - 29
GS1 DataBar Expanded
< Default All GS1 DataBar Expanded Settings >
GS1 DataBar Expanded On/Off
* On
Off
GS1 DataBar Expanded Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74.
Minimum Message Length
Maximum Message Length
Codablock A
Codablock A On/Off
On
* Off
7 - 30
Codablock A Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-600. Minimum Default = 1, Maximum Default = 600.
Minimum Message Length
Maximum Message Length
Codablock F
Codablock F On/Off
On
* Off
Codablock F Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048.
Minimum Message Length
Maximum Message Length
7 - 31
PDF417
< Default All PDF417 Settings >
PDF417 On/Off
* On
Off
PDF417 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750.
Minimum Message Length
Maximum Message Length
MacroPDF417
MacroPDF417 is an implementation of PDF417 capable of encoding very large amounts of data into multiple PDF417 bar
codes. When this selection is enabled, these multiple bar codes are assembled into a single data string. Default = On.
* On
Off
7 - 32
MicroPDF417
< Default All MicroPDF417 Settings >
MicroPDF417 On/Off
On
* Off
MicroPDF417 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-366. Minimum Default = 1, Maximum Default = 366.
Minimum Message Length
Maximum Message Length
GS1 Composite Codes
Linear codes are combined with a unique 2D composite component to form a new class called GS1 Composite symbology.
GS1 Composite symbologies allow for the co-existence of symbologies already in use. Default = Off.
On
* Off
7 - 33
UPC/EAN Version
Scan the UPC/EAN Version On bar code to decode GS1 Composite symbols that have a U.P.C. or an EAN linear component. (This does not affect GS1 Composite symbols with a GS1-128 or GS1 linear component.) Default = UPC/EAN Version Off.
UPC/EAN Version On
* UPC/EAN Version Off
Note: If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to scan and output only the data from
the GS1 DataBar code. See Coupon GS1 DataBar Output (page 7-20) for further information.
GS1 Composite Code Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-2435. Minimum Default = 1, Maximum Default = 2435.
Minimum Message Length
Maximum Message Length
GS1 Emulation
The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent
GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1-128, and
GS1-128 DataBar and GS1 Composites. (Any application that accepts GS1 data can be simplified since it only needs to recognize one data carrier type.)
If GS1-128 Emulation is scanned, all retail codes (U.P.C., UPC-E, EAN8, EAN13) are expanded out to 16 digits. If the AIM ID
is enabled, the value will be the GS1-128 AIM ID, ]C1 (see Symbology Charts on page A-1).
If GS1 DataBar Emulation is scanned, all retail codes (U.P.C., UPC-E, EAN8, EAN13) are expanded out to 16 digits. If the AIM
ID is enabled, the value will be the GS1-DataBar AIM ID, ]em (see Symbology Charts on page A-1).
If GS1 Code Expansion Off is scanned, retail code expansion is disabled, and UPC-E expansion is controlled by the UPC-E0
Expand (page 7-20) setting. If the AIM ID is enabled, the value will be the GS1-128 AIM ID, ]C1 (see Symbology Charts on
page A-1).
If EAN8 to EAN13 Conversion is scanned, all EAN8 bar codes are converted to EAN13 format.
Default = GS1 Emulation Off.
GS1-128 Emulation
7 - 34
GS1 DataBar Emulation
GS1 Code Expansion Off
EAN8 to EAN13 Conversion
* GS1 Emulation Off
TCIF Linked Code 39 (TLC39)
This code is a composite code since it has a Code 39 linear component and a MicroPDF417 stacked code component. All bar
code readers are capable of reading the Code 39 linear component. The MicroPDF417 component can only be decoded if
TLC39 On is selected. The linear component may be decoded as Code 39 even if TLC39 is off. Default = Off.
On
* Off
QR Code
< Default All QR Code Settings >
QR Code On/Off
This selection applies to both QR Code and Micro QR Code.
* On
Off
7 - 35
QR Code Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-7089. Minimum Default = 1, Maximum Default = 7089.
Minimum Message Length
Maximum Message Length
QR Code Append
This function allows the scanner to append the data from several QR Code bar codes together before transmitting them to
the host computer. When the scanner encounters an QR Code bar code with the append trigger character(s), it buffers the
number of QR Code bar codes determined by information encoded in those bar codes. Once the proper number of codes
is reached, the data is output in the order specified in the bar codes. Default = On.
* On
Off
QR Code Page
QR Code pages define the mapping of character codes to characters. If the data received does not display with the proper
characters, it may be because the bar code being scanned was created using a code page that is different from the one the
host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were
created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save bar code from
the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly.
QR Code Page
7 - 36
Data Matrix
< Default All Data Matrix Settings >
Data Matrix On/Off
* On
Off
Data Matrix Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-3116. Minimum Default = 1, Maximum Default = 3116.
Minimum Message Length
Maximum Message Length
Data Matrix Append
This function allows the scanner to append the data from several Data Matrix bar codes together before transmitting them
to the host computer. When the scanner encounters an Data Matrix bar code with the append trigger character(s), it buffers the number of Data Matrix bar codes determined by information encoded in those bar codes. Once the proper number
of codes is reached, the data is output in the order specified in the bar codes. Default = On.
* On
Off
Data Matrix Code Page
Data Matrix Code pages define the mapping of character codes to characters. If the data received does not display with the
proper characters, it may be because the bar code being scanned was created using a code page that is different from the
one the host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar
7 - 37
codes were created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save bar
code from the Programming Chart on the inside the back cover of this manual. The data characters should then appear
properly.
Data Matrix Code Page
MaxiCode
< Default All MaxiCode Settings >
MaxiCode On/Off
On
* Off
MaxiCode Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-150. Minimum Default = 1, Maximum Default = 150.
Minimum Message Length
Maximum Message Length
7 - 38
Aztec Code
< Default All Aztec Code Settings >
Aztec Code On/Off
* On
Off
Aztec Code Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-3832. Minimum Default = 1, Maximum Default = 3832.
Minimum Message Length
Maximum Message Length
Aztec Append
This function allows the scanner to append the data from several Aztec bar codes together before transmitting them to the
host computer. When the scanner encounters an Aztec bar code with the append trigger character(s), it buffers the number
of Aztec bar codes determined by information encoded in those bar codes. Once the proper number of codes is reached,
the data is output in the order specified in the bar codes. Default = On.
* On
Off
Aztec Code Page
Aztec Code pages define the mapping of character codes to characters. If the data received does not display with the
proper characters, it may be because the bar code being scanned was created using a code page that is different from the
one the host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar
7 - 39
codes were created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save bar
code from the Programming Chart on the inside the back cover of this manual. The data characters should then appear
properly.
Aztec Code Page
Chinese Sensible (Han Xin) Code
< Default All Han Xin Settings >
Han Xin Code On/Off
On
* Off
Han Xin Code Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional
information. Minimum and Maximum lengths = 1-7833. Minimum Default = 1, Maximum Default = 7833.
Minimum Message Length
Maximum Message Length
7 - 40
Postal Codes - 2D
The following lists the possible 2D postal codes, and 2D postal code combinations that are allowed. Only one 2D postal code
selection can be active at a time. If you scan a second 2D postal code selection, the first selection is overwritten. Default = 2D
Postal Codes Off.
* 2D Postal Codes Off
Single 2D Postal Codes:
Australian Post On
British Post On
Canadian Post On
Intelligent Mail Bar Code On
Japanese Post On
KIX Post On
Planet Code On
Also see Planet Code
Check Digit, page 7-44.
Postal-4i On
7 - 41
Postnet On
Also see Postnet Check
Digit, page 7-44.
Postnet with B and B’ Fields On
InfoMail On
Combination 2D Postal Codes:
InfoMail and British
Post On
Intelligent Mail Bar Code and
Postnet with B and B’ Fields On
Postnet and
Postal-4i On
Postnet and
Intelligent Mail Bar Code On
Postal-4i and
Intelligent Mail Bar Code On
Postal-4i and
Postnet with B and B’ Fields On
Planet Code and
Postnet On
7 - 42
Planet Code and
Postnet with B and B’ Fields On
Planet Code and
Postal-4i On
Planet Code and
Intelligent Mail Bar Code On
Planet Code,
Postnet, and
Postal-4i On
Planet Code,
Postnet, and
Intelligent Mail Bar Code On
Planet Code,
Postal-4i, and
Intelligent Mail Bar Code On
Postnet,
Postal-4i, and
Intelligent Mail Bar Code On
Planet Code,
Postal-4i, and
Postnet with B and B’ Fields On
Planet Code,
Intelligent Mail Bar Code, and
Postnet with B and B’ Fields On
Postal-4i,
Intelligent Mail Bar Code, and
Postnet with B and B’ Fields On
7 - 43
Planet Code,
Postal-4i,
Intelligent Mail Bar Code, and
Postnet On
Planet Code,
Postal-4i,
Intelligent Mail Bar Code, and
Postnet with B and B’ Fields On
Planet Code Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of Planet Code data. Default
= Don’t Transmit.
Transmit Check Digit
* Don’t Transmit Check Digit
Postnet Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of Postnet data. Default =
Don’t Transmit.
Transmit Check Digit
* Don’t Transmit Check Digit
Australian Post Interpretation
This option controls what interpretation is applied to customer fields in Australian 4-State symbols.
Bar Output lists the bar patterns in “0123” format.
Numeric N Table causes that field to be interpreted as numeric data using the N Table.
Alphanumeric C Table causes the field to be interpreted as alphanumeric data using the C Table. Refer to the Australian
Post Specification Tables.
7 - 44
Combination C and N Tables causes the field to be interpreted using either the C or N Tables.
* Bar Output
Numeric N Table
Alphanumeric C Table
Combination C and N Tables
Postal Codes - Linear
The following lists linear postal codes. Any combination of linear postal code selections can be active at a time.
China Post (Hong Kong 2 of 5)
China Post (Hong Kong 2 of 5) On/Off
On
* Off
China Post (Hong Kong 2 of 5) Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
7 - 45
Maximum Message Length
Korea Post
Korea Post
On
* Off
Korea Post Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
Korea Post Check Digit
This selection allows you to specify whether the check digit should be transmitted. Default = Don’t Transmit.
Transmit Check Digit
* Don’t Transmit Check Digit
7 - 46
8
Interface Keys
Keyboard Function Relationships
The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can
be used with the scanner. Refer to page 2-17 enable Control + X (Control + ASCII) Mode.
Function Code
HEX/ASCII Value
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
Full ASCII (CTRL + X Mode)
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
The last five characters in the Full ASCII “CTRL”+ column ( [ \ ] 6 - ), apply to US only. The following chart indicates the equivalents of these five characters for different countries.
Country
Codes
United States
[
\
]
6
-
Belgium
[
<
]
6
-
Scandinavia
8
<
9
6
-
France
^
8
$
6
=
Germany
Ã
+
6
-
Italy
\
+
6
-
Switzerland
United Kingdom
[
<
..
6
-
¢
]
6
-
8-1
Country
Codes
Denmark
8
\
9
6
-
Norway
8
\
9
6
-
Spain
[
\
]
6
-
Supported Interface Keys
ASCII
HEX
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
DEL
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
7F
8-2
IBM PC/AT and
Compatibles,
USB PC
Keyboard
Reserved
Enter (KP)
Cap Lock
ALT make
ALT break
CTRL make
CTRL break
CR/Enter
Reserved
Tab
Reserved
Tab
Delete
CR/Enter
Insert
Escape
F11
Home
Print
Back Space
Back Tab
F12
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
Apple Mac/iMac
Supported Keys
Reserved
Enter/Numpad Enter
CAPS
ALT make
ALT break
CNTRL make
CNTRL break
RETURN
APPLE make
TAB
APPLE break
TAB
Del
RETURN
Ins Help
ESC
F11
Home
Prnt Scrn
BACKSPACE
LSHIFT TAB
F12
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
BACKSPACE
9
Utilities
To Add a Test Code I.D. Prefix to All Symbologies
This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts,
beginning on page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes,
then programs a Code I.D. prefix for all symbologies. This is a temporary setting that will be removed when the unit is power
cycled.
Add Code I.D. Prefix to
All Symbologies (Temporary)
Show Decoder Revision
Scan the bar code below to output the decoder revision.
Show Decoder Revision
Show Scan Driver Revision
Scan the bar code below to output the scan driver revision. The scan driver controls image capture.
Show Scan Driver Revision
Show Software Revision
Scan the bar code below to output the current software revision, unit serial number, and other product information for both the
scanner and the base.
Show Revision
Show Data Format
Scan the bar code below to show current data format settings.
DFMBK3?.
Data Format Settings
9-1
Test Menu
When you scan the Test Menu On code, then scan a programming code in this manual, the scanner displays the content of a
programming code. The programming function will still occur, but in addition, the content of that programming code is output to
the terminal.
Note: This feature should not be used during normal scanner operation.
On
* Off
EZConfig-Scanning Introduction
EZConfig-Scanning provides a wide range of PC-based programming functions that can be performed on a scanner connected
to your PC's COM port. EZConfig-Scanning allows you to download upgrades to the scanner's firmware, change programmed
parameters, and create and print programming bar codes. Using EZConfig-Scanning, you can even save/open the programming parameters for a scanner. This saved file can be e-mailed or, if required, you can create a single bar code that contains all
the customized programming parameters and mail or fax that bar code to any location. Users in other locations can scan the
bar code to load in the customized programming.
To communicate with a scanner, EZConfig-Scanning requires that the PC have at least one available serial communication port,
or a serial port emulation using a physical USB port. If you are using the serial port and RS232 cable, an external power supply
is required. When using a USB serial port emulation, only a USB cable is required.
EZConfig-Scanning Operations
The EZConfig-Scanning software performs the following operations:
Scan Data
Scan Data allows you to scan bar codes and display the bar code data in a window. Scan Data lets you send serial
commands to the scanner and receive scanner response that can be seen in the Scan Data window. The data displayed in the Scan Data window can either be saved in a file or printed.
Configure
Configure displays the programming and configuration data of the scanner. The scanner's programming and configuration data is grouped into different categories. Each category is displayed as a tree item under the "Configure" tree
node in the application explorer. When one of these tree nodes is clicked, the right-hand side is loaded with the
parameters' form belonging to that particular category. The "Configure" tree option has all the programming and configuration parameters specified for a scanner. You can set or modify these parameters as required. You can later write
the modified settings to the scanner, or save them to a dcf file.
Installing EZConfig-Scanning from the Web
Note: EZConfig-Scanning requires .NET software. If .NET is not installed on your PC, you will be prompted to install it
during the EZConfig-Scanning installation.
1. Access the Honeywell web site at www.honeywellaidc.com.
2. Click on the Resources tab. Select Software.
3. Click on the dropdown for Select Product Number. Click on your product number.
4. Click on the listing for EZConfig-Scanning.
9-2
5. When prompted, select Save File, and save the files to the c:\windows\temp directory.
6. Once you have finished downloading the file, exit the web site.
7. Using Explorer, go to the c:\windows\temp file.
8. Double click on the Setup.exe file. Follow the screen prompts to install the EZConfig-Scanning program.
9. If you’ve selected the defaults during installation, you can click on Start Menu-All Programs-Honeywell-EZConfigScanning.
Resetting the Factory Defaults
!
This selection erases all your settings and resets the scanner to the original factory defaults. It also disables all plugins.
If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scanner to factory default settings, first scan the Remove Custom Defaults bar code, then scan Activate Defaults. This resets the
scanner to the factory default settings.
Remove Custom Defaults
Activate Defaults
Note: If using a cordless system, scanning the Activate Defaults bar code also causes both the scanner and the base or Access
Point to perform a reset and become unlinked. The scanner must be placed in its base to re-establish the link before any
setup codes are entered. If using an Access Point, the linking bar code must be scanned. See Cordless System
Operation beginning on page 3-1 for additional information.
The Menu Commands, beginning on page 10-3 list the factory default settings for each of the commands (indicated by an asterisk (*) on the programming pages).
9-3
9-4
10
Serial Programming Commands
The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the
programming bar codes will program the scanner. For complete descriptions and examples of each serial programming command, refer to the corresponding programming bar code in this manual.
The device must be set to an RS232 interface (see page 2-1). The following commands can be sent via a PC COM port using
terminal emulation software.
Conventions
The following conventions are used for menu and query command descriptions:
parameterA label representing the actual value you should send as part of a command.
[option] An optional part of a command.
{Data} Alternatives in a command.
bold
Names of menus, menu commands, buttons, dialog boxes, and windows that appear on the screen.
Menu Command Syntax
Menu commands have the following syntax (spaces have been used for clarity only):
Prefix [:Name:] Tag SubTag {Data} [, SubTag {Data}] [; Tag SubTag {Data}] […] Storage
Prefix Three ASCII characters: SYN M CR (ASCII 22,77,13).
:Name: This command is only used with cordless devices. It is used to specify whether you’re communicating with the base or
the scanner. To send information to the scanner (with the base connected to host), use :Voyager_1452g: The default
factory setting for a Voyager 1452g scanner is Voyager_1452 scanner. This setting is changed by using the BT_NAM
command, which accepts alphanumeric values. If the name is not known, a wildcard (*) can be used :*:.
Note: Since the base stores all work group settings and transfers to them to scanner once they are linked, changes are typically
done to the base and not to the scanner.
Tag
A 3 character case-insensitive field that identifies the desired menu command group. For example, all RS232
configuration settings are identified with a Tag of 232.
SubTag A 3 character case-insensitive field that identifies the desired menu command within the tag group. For example, the
SubTag for the RS232 baud rate is BAD.
Data
The new value for a menu setting, identified by the Tag and SubTag.
Storage A single character that specifies the storage table to which the command is applied. An exclamation point (!) performs
the command’s operation on the device’s volatile menu configuration table. A period (.) performs the command’s
operation on the device’s non-volatile menu configuration table. Use the non-volatile table only for semi-permanent
changes you want saved through a power cycle.
Query Commands
Several special characters can be used to query the device about its settings.
^
?
*
What is the default value for the setting(s).
What is the device’s current value for the setting(s).
What is the range of possible values for the setting(s). (The device’s response uses a dash (-) to indicate a
continuous range of values. A pipe (|) separates items in a list of non-continuous values.)
:Name: Field Usage (Optional)
This command returns the query information from the scanner.
Tag Field Usage
When a query is used in place of a Tag field, the query applies to the entire set of commands available for the particular
storage table indicated by the Storage field of the command. In this case, the SubTag and Data fields should not be used
because they are ignored by the device.
10 - 1
SubTag Field Usage
When a query is used in place of a SubTag field, the query applies only to the subset of commands available that match the
Tag field. In this case, the Data field should not be used because it is ignored by the device.
Data Field Usage
When a query is used in place of the Data field, the query applies only to the specific command identified by the Tag and
SubTag fields.
Concatenation of Multiple Commands
Multiple commands can be issued within one Prefix/Storage sequence. Only the Tag, SubTag, and Data fields must be
repeated for each command in the sequence. If additional commands are to be applied to the same Tag, then the new
command sequence is separated with a comma (,) and only the SubTag and Data fields of the additional command are
issued. If the additional command requires a different Tag field, the command is separated from previous commands by a
semicolon (;).
Responses
The device responds to serial commands with one of three responses:
ACK Indicates a good command which has been processed.
ENQ Indicates an invalid Tag or SubTag command.
NAK Indicates the command was good, but the Data field entry was out of the allowable range for this Tag and SubTag
combination, e.g., an entry for a minimum message length of 100 when the field will only accept 2 characters.
When responding, the device echoes back the command sequence with the status character inserted directly before each
of the punctuation marks (the period, exclamation point, comma, or semicolon) in the command.
Examples of Query Commands
In the following examples, a bracketed notation [ ] depicts a non-displayable response.
Example: What is the range of possible values for Codabar Coding Enable?
Enter:
cbrena*.
Response: CBRENA0-1[ACK]
This response indicates that Codabar Coding Enable (CBRENA) has a range of values from 0 to 1 (off and on).
Example: What is the default value for Codabar Coding Enable?
Enter:
cbrena^.
Response: CBRENA1[ACK]
This response indicates that the default setting for Codabar Coding Enable (CBRENA) is 1, or on.
Example: What is the device’s current setting for Codabar Coding Enable?
Enter:
cbrena?.
Response: CBRENA1[ACK]
This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on.
Example: What are the device’s settings for all Codabar selections?
Enter:
cbr?.
Response: CBRENA1[ACK],
SSX0[ACK],
CK20[ACK],
CCT1[ACK],
MIN2[ACK],
MAX60[ACK],
DFT[ACK].
10 - 2
This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on;
the Start/Stop Character (SSX) is set to 0, or Don’t Transmit;
the Check Character (CK2) is set to 0, or Not Required;
concatenation (CCT) is set to 1, or Enabled;
the Minimum Message Length (MIN) is set to 2 characters;
the Maximum Message Length (MAX) is set to 60 characters;
and the Default setting (DFT) has no value.
Trigger Commands
You can activate and deactivate the scanner with serial trigger commands. First, the scanner must be put in Manual Trigger
Mode by scanning a Manual Trigger Mode bar code (page 4-5), or by sending a serial menu command for triggering (page 4-5).
Once the scanner is in serial trigger mode, the trigger is activated and deactivated by sending the following commands:
Activate:
SYN T CR
Deactivate: SYN U CR
The scanner scans until a bar code has been read, until the deactivate command is sent, or until the serial time-out has been
reached (see "Read Time-Out" on page 4-7 for a description, and the serial command on page 10-11).
Resetting the Custom Defaults
If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults bar code below. This
resets the scanner to the custom default settings. If there are no custom defaults, it will reset the scanner to the factory default
settings. Any settings that have not been specified through the custom defaults will be defaulted to the factory default settings.
Activate Custom Defaults
Note: If using a cordless system, scanning this bar code also causes both the scanner and the base or Access Point to perform
a reset and become unlinked. The scanner must be placed in its base to re-establish the link. If using an Access Point,
the linking bar code must be scanned. See Cordless System Operation beginning on page 3-1 for additional information.
The charts on the following pages list the factory default settings for each of the commands (indicated by an asterisk (*) on the
programming pages).
Menu Commands
Selection
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Set Custom Defaults
MNUCDP
1-7
Save Custom Defaults
MNUCDS
1-7
Activate Custom Defaults
DEFALT
1-7
Keyboard Wedge:
IBM PC AT and Compatibles with CR suffix
PAP_AT
2-1
Laptop Direct Connect with CR suffix
PAPLTD
2-1
Page
Product Default Settings
Setting Custom Defaults
Resetting the Custom Defaults
Programming the Interface
Plug and Play Codes
Plug and Play Codes:
RS485
RS232 Serial Port
PAP232
2-1
IBM Port 5B Interface
PAPP5B
2-2
IBM Port 9B HHBCR-1 Interface
PAP9B1
2-2
IBM Port 17 Interface
PAPP17
2-2
10 - 3
Selection
Plug and Play Codes: IBM SurePos
Plug and Play Codes: USB
Remote MasterMind for USB
Plug and Play Codes
Program Keyboard
Country
10 - 4
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
IBM Port 9B HHBCR-2 Interface
PAP9B2
2-2
RS485 Packet Mode On
RTLPDF1
2-2
*RS485 Packet Mode Off
RTLPDF0
2-2
Page
RS485 Packet Length (20-256) *40
RTLMPS
2-3
USB IBM SurePos Handheld
PAPSPH
2-3
USB IBM SurePos Tabletop
PAPSPT
2-3
USB Keyboard (PC)
PAP124
2-3
USB Keyboard (Mac)
PAP125
2-3
USB Japanese Keyboard (PC)
TRMUSB134
2-3
USB HID
PAP131
2-4
USB Serial
TRMUSB130
2-4
CTS/RTS Emulation On
USBCTS1
2-4
CTS/RTS Emulation Off*
USBCTS0
2-4
ACK/NAK Mode On
USBACK1
2-4
ACK/NAK Mode Off*
USBACK0
2-4
ReM Off
REMIFC0
2-5
*ReM On
REMIFC1
2-5
Verifone Ruby Terminal
PAPRBY
2-5
Gilbarco Terminal
PAPGLB
2-5
Honeywell Bioptic Aux Port
PAPBIO
2-6
Datalogic Magellan Bioptic Aux Port
PAPMAG
2-6
NCR Bioptic Aux Port
PAPNCR
2-6
Wincor Nixdorf Terminal
PAPWNX
2-6
Wincor Nixdorf Beetle
PAPBTL
2-7
Wincor Nixdorf RS232 Mode A
PAPWMA
2-7
*U.S.A.
KBDCTY0
2-8
Albania
KBDCTY35
2-8
Azeri (Cyrillic)
KBDCTY81
2-8
Azeri (Latin)
KBDCTY80
2-8
Belarus
KBDCTY82
2-8
Belgium
KBDCTY1
2-8
Bosnia
KBDCTY33
2-8
Brazil
KBDCTY16
2-8
Brazil (MS)
KBDCTY59
2-8
Bulgaria (Cyrillic)
KBDCTY52
2-8
Bulgaria (Latin)
KBDCTY53
2-9
Canada (French legacy)
KBDCTY54
2-9
Canada (French)
KBDCTY18
2-9
Canada (Multilingual)
KBDCTY55
2-9
Croatia
KBDCTY32
2-9
Czech
KBDCTY15
2-9
Czech (Programmers)
KBDCTY40
2-9
Selection
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Czech (QWERTY)
KBDCTY39
2-9
Czech (QWERTZ)
KBDCTY38
2-9
Denmark
KBDCTY8
2-9
Dutch (Netherlands)
KBDCTY11
2-9
Estonia
KBDCTY41
2-10
Faeroese
KBDCTY83
2-10
Finland
KBDCTY2
2-10
France
KBDCTY3
2-10
Gaelic
KBDCTY84
2-10
Germany
KBDCTY4
2-10
Greek
KBDCTY17
2-10
Greek (220 Latin)
KBDCTY64
2-10
Greek (220)
KBDCTY61
2-10
Greek (319 Latin)
KBDCTY65
2-10
Greek (319)
KBDCTY62
2-10
Greek (Latin)
KBDCTY63
2-11
Greek (MS)
KBDCTY66
2-11
Greek (Polytonic)
KBDCTY60
2-11
Hebrew
KBDCTY12
2-11
Hungarian (101 key)
KBDCTY50
2-11
Hungary
KBDCTY19
2-11
Iceland
KBDCTY75
2-11
Irish
KBDCTY73
2-11
Italian (142)
KBDCTY56
2-11
Italy
KBDCTY5
2-11
Japan ASCII
KBDCTY28
2-11
Kazakh
KBDCTY78
2-12
Kyrgyz (Cyrillic)
KBDCTY79
2-12
Latin America
KBDCTY14
2-12
Latvia
KBDCTY42
2-12
Latvia (QWERTY)
KBDCTY43
2-12
Lithuania
KBDCTY44
2-12
Lithuania (IBM)
KBDCTY45
2-12
Macedonia
KBDCTY34
2-12
Malta
KBDCTY74
2-12
Mongolian (Cyrillic)
KBDCTY86
2-12
Norway
KBDCTY9
2-12
Poland
KBDCTY20
2-13
Polish (214)
KBDCTY57
2-13
Polish (Programmers)
KBDCTY58
2-13
Portugal
KBDCTY13
2-13
Romania
KBDCTY25
2-13
Russia
KBDCTY26
2-13
Page
10 - 5
Selection
Keyboard Conversion
Keyboard Style
Control Character Output
Keyboard Modifiers
10 - 6
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Russian (MS)
KBDCTY67
2-13
Russian (Typewriter)
KBDCTY68
2-13
SCS
KBDCTY21
2-13
Serbia (Cyrillic)
KBDCTY37
2-13
Serbia (Latin)
KBDCTY36
2-13
Slovakia
KBDCTY22
2-14
Slovakia (QWERTY)
KBDCTY49
2-14
Slovakia (QWERTZ)
KBDCTY48
2-14
Slovenia
KBDCTY31
2-14
Spain
KBDCTY10
2-14
Spanish variation
KBDCTY51
2-14
Sweden
KBDCTY23
2-14
Switzerland (French)
KBDCTY29
2-14
Switzerland (German)
KBDCTY6
2-14
Tatar
KBDCTY85
2-14
Turkey F
KBDCTY27
2-14
Turkey Q
KBDCTY24
2-15
Ukrainian
KBDCTY76
2-15
United Kingdom
KBDCTY7
2-15
United Stated (Dvorak right)
KBDCTY89
2-15
United States (Dvorak left)
KBDCTY88
2-15
United States (Dvorak)
KBDCTY87
2-15
United States (International)
KBDCTY30
2-15
Uzbek (Cyrillic)
KBDCTY77
2-15
*Keyboard Conversion Off
KBDCNV0
2-16
Convert all Characters to Upper Case
KBDCNV1
2-16
Convert all Characters to Lower Case
KBDCNV1
2-16
*Regular
KBDSTY0
2-15
Caps Lock
KBDSTY1
2-15
Shift Lock
KBDSTY2
2-16
Automatic Caps Lock
KBDSTY6
2-16
Emulate External
Keyboard
KBDSTY5
2-16
*Control Character Output Off
KBDNPE0
2-17
*Control Character Output On
KBDNPE1
2-17
*Control + ASCII Off
KBDCAS0
2-17
DOS Mode Control + ASCII
KBDCAS1
2-17
Windows Mode Control + ASCII
KBDCAS2
2-17
Windows Mode Prefix/Suffix Off
KBDCAS3
2-17
*Turbo Mode Off
KBDTMD0
2-18
Page
Selection
Baud Rate
Word Length: Data Bits, Stop Bits,
and Parity
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Turbo Mode On
KBDTMD1
2-18
*Numeric Keypad Off
KBDNPS0
2-18
Numeric Keypad On
KBDNPS1
2-18
*Auto Direct Connect Off
KBDADC0
2-18
Auto Direct Connect On
KBDADC1
2-18
300 BPS
232BAD0
2-18
600 BPS
232BAD1
2-18
1200 BPS
232BAD2
2-19
2400 BPS
232BAD3
2-19
4800 BPS
232BAD4
2-19
*9600 BPS
232BAD5
2-19
19200 BPS
232BAD6
2-19
38400 BPS
232BAD7
2-19
57600 BPS
232BAD8
2-19
115200 BPS
232BAD9
2-19
7 Data, 1 Stop, Parity Even
232WRD3
2-19
7 Data, 1 Stop, Parity None
232WRD0
2-20
7 Data, 1 Stop, Parity Odd
232WRD6
2-20
7 Data, 2 Stop, Parity Even
232WRD4
2-20
7 Data, 2 Stop, Parity None
232WRD1
2-20
7 Data, 2 Stop, Parity Odd
232WRD7
2-20
8 Data, 1 Stop, Parity Even
232WRD5
2-20
*8 Data, 1 Stop, Parity None
232WRD2
2-20
Page
8 Data, 1 Stop, Parity Odd
232WRD8
2-20
RS232 Receiver Time-out
Range 0 - 300 seconds
232LPT###
2-20
RS232 Handshaking
*RTS/CTS Off
232CTS0
2-21
Flow Control, No Timeout
232CTS1
2-21
Two-Direction Flow Control
232CTS2
2-21
Flow Control with Timeout
232CTS3
2-21
RS232 Timeout
232DEL####
2-21
*XON/XOFF Off
232XON0
2-21
XON/XOFF On
232XON1
2-21
*ACK/NAK Off
232ACK0
2-22
ACK/NAK On
232ACK1
2-22
*Packet Mode Off
232PKT0
2-22
Scanner-Bioptic Packet Mode
Packet Mode On
232PKT2
2-22
Scanner-Bioptic ACK/NAK Mode
*Bioptic ACK/NAK Off
232NAK0
2-22
Bioptic ACK/NAK On
232NAK1
2-22
Scanner-Bioptic ACK/NAK Timeout
ACK/NAK Timeout
*5100
232DLK#####
2-23
10 - 7
Selection
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Page
Cordless System Operation
Note: This section applies only to cordless systems. It does not apply to corded scanners.
Base Power Communication
Indicator
*On
:*:BASRED1
3-5
Off
:*:BASRED0
3-5
Reset Scanner
Reset Scanner
RESET_
3-6
Scanning in Cradle Off
BT_SIC0
3-6
*Scanning in Cradle On
BT_SIC1
3-6
Shut Down Scanner in Cradle
BT_SIC2
3-6
Base Charge Off
BASCHG0
3-7
*External or Interface Cable Power
BASCHG1
3-7
External Power Only
BASCHG2
3-7
*On
BEPPGE1
3-7
Off
BEPPGE0
3-7
Low (*1000 Hz)
BEPPFQ1000
3-7
Medium (3250 Hz)
BEPPFQ3250
3-8
Scanning While in Base Cradle
Base Charging Modes
Paging Mode
Paging Pitch
Beeper Pitch - Base Error
Number of Beeps - Base Error
High (4200)
BEPPFQ4200
3-8
*Razz (250) (min 200Hz)
BASFQ2250
3-8
Medium (3250)
BASFQ23250
3-8
High (4200) (max 9000Hz)
BASFQ24200
3-8
*1
BASERR3
3-8
Range 1 - 9
BASERR#
3-8
Scanner Report
Scanner Report
RPTSCN
3-8
Scanner Address
Scanner Address
BT_LDA
3-9
Base Address
Base Address
:*:BASLDA
3-9
Scanner Modes
Charge Only Mode
:*:BASLNK0
3-9
*Charge and Link Mode
:*:BASLNK1
3-9
Locked Link Mode
BASCON0,DNG1
3-10
*Open Link Mode
BASCON1,DNG1
3-10
Unlink Scanner
BT_RMV
3-10
Out-of-Range Alarm
Alarm Sound Type
Scanner Power Time-Out Timer
10 - 8
Override Locked Scanner
BT_RPL1
3-10
Base Alarm Duration (Range 1 - 3000 sec
(*0))
BASORD
3-11
Scanner Alarm Duration (Range 1 - 3000
sec (*0))
BT_ORD
3-11
Base Alarm Type
BASORW
3-11
Scanner Alarm Type
BT_ORW
3-11
Timer (0-7200 seconds)
BT_LPT0
3-12
200 Seconds
BT_LPT200
3-12
400 Seconds
BT_LPT400
3-12
900 Seconds
BT_LPT900
3-12
3600 Seconds
BT_LPT3600
3-12
7200 Seconds
BT_LPT7200
3-12
Selection
Flexible Power Management
Batch Mode
Batch Mode Beep
Batch Mode Storage
Batch Mode Quantity
Quantity Codes
Batch Mode Output Order
Total Records
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
*Full Power
BT_TXP100
3-13
Medium Power
BT_TXP35
3-13
Medium Low Power
BT_TXP5
3-13
Page
Low Power
BT_TXP1
3-13
Automatic Batch Mode
BATENA1
3-13
*Batch Mode Off
BATENA0
3-13
Inventory Batch Mode
BATENA2
3-13
Persistent Batch Mode
BATENA3
3-14
Off
BATBEP0
3-14
*On
BATBEP1
3-14
*Flash Storage
BATNVS1
3-14
RAM Storage
BATNVS0
3-14
*Off
BATQTY0
3-15
On
BATQTY1
3-15
0
BATNUM0
3-15
*1
BATNUM1
3-16
2
BATNUM2
3-16
3
BATNUM3
3-16
4
BATNUM4
3-16
5
BATNUM5
3-16
6
BATNUM6
3-16
7
BATNUM7
3-16
8
BATNUM8
3-16
9
BATNUM9
3-16
*FIFO
BATLIF0
3-16
LIFO
BATLIF1
3-16
Total Records
BATNRC
3-17
Delete Last Code
Delete Last Code
BATUND
3-17
Clear All Codes
Clear All Codes
BATCLR
3-17
Transmit Records to Host
Transmit Inventory Records
BAT_TX
3-17
Batch Mode Transmit Delay
*Off
BATDLY0
3-17
Short (ms)
BATDLY250
3-17
Medium (ms)
BATDLY500
3-18
Long (ms)
BATDLY1000
3-18
Multiple Scanner Operation
BASCON2,DNG3
3-18
Name 1-7
BT_NAM#####
3-18
Reset
RESET_
3-19
Multiple Scanner
Operation
Scanner Name
Scanner Name
BT_NAM
3-19
Application Work Group
Selections
*Group 0
GRPSEL0
3-19
Group 1-6
GRPSEL#
3-19
Resetting the Factory Defaults: All
Application Work Groups
Factory Default Settings:
All Work Groups
PAPDFT&
3-20
10 - 9
Selection
Resetting the Custom Defaults: All
Application Work Groups
Bluetooth Connection
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Custom Default Settings:
All Work Groups
PAPDFT
3-21
Page
Bluetooth HID Keyboard Connect
PAPBTH
3-21
Bluetooth HID Keyboard Disconnect
PAPSPP
3-23
Bluetooth Serial Port - PCs/Laptops
BT_TRM0;BT_DNG5
3-23
BT Connection - PDA/Mobility Systems
Device
BT_TRM0;BT_DNG1
3-23
Bluetooth PIN Code
BT_PIN
3-23
Auto Reconnect Mode
*Auto Reconnect On
BT_ACM1
3-24
Auto Reconnect Off
BT_ACM0
3-24
Maximum Link Attempts
Maximum Link Attempts
BT_MLA
3-25
Relink Time-Out
Relink Time-Out
BT_RLT
3-25
Host Command Acknowledgment
Host ACK On
HSTACK1
3-27
*Host ACK Off
HSTACK0
3-27
Power Up Beeper Off - Scanner
BEPPWR0
4-1
*Power Up Beeper On - Scanner
BEPPWR1
4-1
Beep on BEL On
BELBEP1
4-1
*Beep on BEL Off
BELBEP0
4-1
Input/Output Selections
Power Up Beeper
Beep on BEL Character
Trigger Click
Beep on BEL Character
Beeper - Good Read
Beeper Volume - Good Read
On
BEPTRG1
4-2
*Off
BEPTRG0
4-1
Beep on BEL On
BELBEP1
4-1
*Beep on BEL Off
BELBEP0
4-1
Off
BEPBEP0
4-2
*On
BEPBEP1
4-2
Off
BEPLVL0
4-2
Low
BEPLVL1
4-2
Medium
BEPLVL2
4-2
*High
BEPLVL3
4-2
Beeper Pitch - Good Read
(Frequency)
Low (1600) (min 400Hz)
BEPFQ11600
4-2
*Medium (2400)
BEPFQ12400
4-3
High (4200) (max 9000Hz)
BEPFQ14200
4-3
Beeper Pitch - Error (Frequency)
*Razz (250) (min 200Hz)
BEPFQ2800
4-3
Medium (3250)
BEPFQ23250
4-3
High (4200) (max 9000Hz)
BEPFQ24200
4-3
Beeper Duration - Good Read
LED - Good Read
Number of Beeps - Error
Number of Beeps - Good Read
10 - 10
*Normal Beep
BEPBIP0
4-3
Short Beep
BEPBIP1
4-3
Off
BEPLED0
4-3
*On
BEPLED1
4-3
*1
BEPERR3
4-4
Range 1 - 9
BEPERR#
4-4
*1
BEPRPT1
4-4
Range 1 - 9
BEPRPT#
4-4
Selection
Good Read Delay
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
*No Delay
DLYGRD0
4-4
Short Delay (500 ms)
DLYGRD500
4-4
Medium Delay (1000 ms)
DLYGRD1000
4-4
Page
Long Delay (1500 ms)
DLYGRD1500
4-4
User-Specified Good Read Delay
Range 0 - 30,000 ms
DLYGRD#####
4-4
Manual Trigger Mode
*Manual Trigger - Normal
PAPHHF
4-5
LED Illumination - Manual Trigger
Low
PWRNOL7
4-5
Medium
PWRNOL15
4-5
Medium High
PWRNOL50
4-5
*High
PWRNOL150
4-5
Serial Trigger Mode
Read Time-Out (range 0-300,000) *30,000
TRGSTO######
4-5
Presentation
Presentation Mode
PAPPST
4-6
Idle Illumination - Presentation
Mode
Low
PWRIDL7
4-6
Medium
PWRIDL15
4-6
*High
PWRIDL50
4-6
Presentation Sensitivity
Range 0-20 (*1)
TRGPMS##
4-6
Presentation Centering Window
Presentation Centering On
PDCWIN1
4-7
*Presentation Centering Off
PDCWIN0
4-7
Left of Presentation Centering Window
(*40%)
PDCLFT###
4-8
Right of Presentation Centering Window
(*60%)
PDCRGT###
4-8
Top of Presentation Centering Window
(*40%)
PDCTOP###
4-7
Bottom of Presentation Centering Window
(*60%)
PDCBOT###
4-7
*Sensor On
TRGSSW1
4-8
Sensor Off
TRGSSW0
4-8
Poor Quality 1D Reading On
DECLDI1
4-8
*Poor Quality 1D Reading Off
DECLDI0
4-8
Poor Quality PDF Reading On
PDFXPR1
4-9
*Poor Quality PDF Reading Off
PDFXPR0
4-9
*CodeGate Off Out-of-Stand
AOSCGD0.
4-9
In-Stand Sensor Mode
Poor Quality Codes
CodeGate
CodeGate On Out-of-Stand
AOSCGD1.
4-9
Mobile Phone Read Mode
Hand Held Scanning - Mobile Phone
PAPHHC
4-9
Hands Free Time-Out
Range 0 - 300,000 ms
TRGPTO######
4-10
Reread Delay
Short (500 ms)
DLYRRD500
4-10
*Medium (750 ms)
DLYRRD750
4-10
Long (1000 ms)
DLYRRD1000
4-10
Extra Long (2000 ms)
DLYRRD2000
4-10
10 - 11
Selection
2D Reread Delay
Character Activation Mode
Character Deactivation Mode
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
*2D Reread Delay Off
DLY2RR0
4-10
Short (1000ms)
DLY2RR1000
4-11
Medium (2000ms)
DLY2RR2000
4-11
Long (3000ms)
DLY2RR3000
4-11
Extra Long (4000ms)
DLY2RR4000
4-11
*Off
HSTCEN0
4-11
On
HSTCEN1
4-11
Activation Character
HSTACH##
4-11
Do Not End Character Activation After Good
Read
HSTCGD0
4-12
*End Character Activation After Good Read
HSTCGD1
4-12
Character Activation Laser Timeout (Range
1 - 65525) *5000 ms
HSTCDT#####
4-12
*Off
HSTDEN0
4-12
On
HSTDEN1
4-12
Page
Deactivation Character
HSTDCH##
4-12
User-Specified Reread Delay
Range 0 - 30,000 ms
DLYRRD#####
4-10
Illumination Lights
*Lights On
SCNLED1
4-13
Lights Off
SCNLED0
4-13
Aimer Delay
200 milliseconds
SCNDLY200
4-13
400 milliseconds
SCNDLY400
4-13
*Off (no delay)
SCNDLY0
4-13
User-Specified Aimer Delay
Range 0 - 4,000 ms
SCNDLY####
4-13
Aimer Mode
Off
SCNAIM0
4-13
*Interlaced
SCNAIM2
4-14
Centering Window
Centering On
DECWIN1
4-14
*Centering Off
DECWIN0
4-15
Left of Centering Window (*40%)
DECLFT###
4-15
Right of Centering Window (*60%)
DECRGT###
4-15
Top of Centering Window (*40%)
DECTOP###
4-15
Bottom of Centering Window (*60%)
DECBOT###
4-15
On
SHWNRD1
4-15
*Off
SHWNRD0
4-15
No Read
Video Reverse
Working Orientation
Video Reverse Only
VIDREV1
4-16
Video Reverse and Standard Bar Codes
VIDREV2
4-16
*Video Reverse Off
VIDREV0
4-16
*Upright
ROTATN0
4-17
Vertical, Bottom to Top (Rotate CCW 90°)
ROTATN1
4-17
Upside Down
ROTATN2
4-17
Vertical, Top to Bottom (Rotate CW 90°)
ROTATN3
4-17
VSUFCR
5-2
Add Prefix
PREBK2##
5-2
Prefix/Suffix Selections
Add CR Suffix to All Symbologies
Prefix
10 - 12
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Clear One Prefix
PRECL2
5-2
Clear All Prefixes
PRECA2
5-2
Add Suffix
SUFBK2##
5-2
Clear One Suffix
SUFCL2
5-2
Clear All Suffixes
SUFCA2
5-2
Function Code Transmit
*Enable
RMVFNC0
5-3
Disable
RMVFNC1
5-3
Intercharacter Delay
Range 0 - 1000 (5ms increments)
DLYCHR##
5-3
User Specified
Intercharacter Delay
Delay Length
0 - 1000 (5ms increments)
DLYCRX##
5-4
Selection
Suffix
Page
Character to Trigger Delay
DLY_XX##
5-4
Interfunction Delay
Range 0 - 1000 (5ms increments)
DLYFNC##
5-4
Intermessage Delay
Range 0 - 1000 (5ms increments)
DLYMSG##
5-4
*Default Data Format (None)
DFMDF3
6-1
Enter Data Format
DFMBK3##
6-2
Clear One Data Format
DFMCL3
6-2
Clear All Data Formats
DFMCA3
6-2
Data Formatter Off
DFM_EN0
6-9
*Data Formatter On,
Not Required,
Keep Prefix/Suffix
DFM_EN1
6-9
Data Format Required,
Keep Prefix/Suffix
DFM_EN2
6-9
Data Formatter Selections
Data Format Editor
Data Formatter
Primary/Alternate Data Formats
Primary Data Format
ALTFNM0
6-9
Data Format 1
ALTFNM1
6-9
Data Format 2
ALTFNM2
6-9
Data Format 3
ALTFNM3
6-10
All Symbologies Off
ALLENA0
7-1
All Symbologies On
ALLENA1
7-1
Default All Codabar
Settings
CBRDFT
7-2
Off
CBRENA0
7-2
Symbologies
All Symbologies
Codabar
*On
CBRENA1
7-2
Codabar Start/Stop Char.
*Don’t Transmit
CBRSSX0
7-2
Transmit
CBRSSX1
7-2
Codabar Check Char.
*No Check Char.
CBRCK20
7-2
Validate, But Don’t Transmit
CBRCK21
7-3
Validate, and Transmit
CBRCK22
7-3
*Off
CBRCCT0
7-3
Codabar Concatenation
10 - 13
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
On
CBRCCT1
7-3
Require
CBRCCT2
7-3
Minimum (2 - 60) *4
CBRMIN##
7-3
Maximum (2 - 60) *60
CBRMAX##
7-3
Default All Code 39
Settings
C39DFT
7-4
Off
C39ENA0
7-4
*On
C39ENA1
7-4
Code 39 Start/Stop Char.
*Don’t Transmit
C39SSX0
7-4
Transmit
C39SSX1
7-4
Code 39 Check Char.
*No Check Char.
C39CK20
7-4
Validate, But Don’t
Transmit
C39CK21
7-4
Validate,
and Transmit
C39CK22
7-4
Selection
Codabar Message Length
Code 39
Code 39 Message Length
Page
Minimum (0 - 48) *0
C39MIN##
7-5
Maximum (0 - 48) *48
C39MAX##
7-5
Code 39 Append
*Off
C39APP0
7-5
On
C39APP1
7-5
Code 32 Pharmaceutical (PARAF)
*Off
C39B320
7-5
On
C39B321
7-5
*Off
C39ASC0
7-6
On
C39ASC1
7-6
Code 39 Code Page
C39DCP
7-6
Default All Interleaved
2 of 5 Settings
I25DFT
7-7
Off
I25ENA0
7-7
Code 39 Full ASCII
Interleaved 2 of 5
Interleaved 2 of 5 Check Digit
Interleaved 2 of 5 Message Length
NEC 2 of 5
NEC 2 of 5 Check Digit
10 - 14
*On
I25ENA1
7-7
*No Check Char.
I25CK20
7-7
Validate, But Don’t
Transmit
I25CK21
7-7
Validate, and Transmit
I25CK22
7-7
Minimum (2 - 80) *4
I25MIN##
7-7
Maximum (2 - 80) *80
I25MAX##
7-8
Default All NEC
2 of 5 Settings
N25DFT
7-8
Off
N25ENA0
7-8
*On
N25ENA1
7-8
*No Check Char.
N25CK20
7-8
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Validate, But Don’t
Transmit
N25CK21
7-8
Validate, and Transmit
N25CK22
7-8
Minimum (2 - 80) *4
N25MIN##
7-9
Maximum (2 - 80) *80
N25MAX##
7-9
Default All Code 93
Settings
C93DFT
7-9
Off
C93ENA0
7-9
*On
C93ENA1
7-11
Minimum (0 - 80) *0
C93MIN##
7-9
Maximum (0 - 80) *80
C93MAX##
7-9
On
C93APP1
7-10
*Off
C93APP0
7-10
Code 93 Code Page
Code 93 Code Page
C93DCP
7-10
Straight 2 of 5 Industrial
Default All Straight 2 of 5 Industrial Settings
R25DFT
7-11
*Off
R25ENA0
7-11
Selection
NEC 2 of 5 Message Length
Code 93
Code 93 Message Length
Code 93 Append
Page
On
R25ENA1
7-11
Straight 2 of 5 Industrial Message
Length
Minimum (1 - 48) *4
R25MIN##
7-11
Maximum (1 - 48) *48
R25MAX##
7-11
Straight 2 of 5 IATA
Default All Straight 2 of 5 IATA
Settings
A25DFT
7-12
Straight 2 of 5 IATA
*Off
A25ENA0
7-12
On
A25ENA1
7-12
Straight 2 of 5 IATA Message
Length
Minimum (1 - 48) *4
A25MIN##
7-12
Maximum (1 - 48) *48
A25MAX##
7-12
Matrix 2 of 5
Default All Matrix 2 of 5
Settings
X25DFT
7-13
*Off
X25ENA0
7-13
On
X25ENA1
7-13
Minimum (1 - 80) *4
X25MIN##
7-13
Maximum (1 - 80) *80
X25MAX##
7-13
Default All Code 11
Settings
C11DFT
7-14
*Off
C11ENA0
7-14
On
C11ENA1
7-14
1 Check Digit
C11CK20
7-14
Matrix 2 of 5 Message Length
Code 11
Code 11 Check Digits Required
*2 Check Digits
C11CK21
7-14
Code 11 Message Length
Minimum (1 - 80) *4
C11MIN##
7-14
Maximum (1 - 80) *80
C11MAX##
7-14
Code 128
Default All Code 128
Settings
128DFT
7-15
10 - 15
Selection
ISBT Concatenation
Code 128 Message Length
Code 128 Append
Code 128 Code Page
GS1-128
GS1-128 Message Length
UPC-A
UPC-A Check Digit
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Off
128ENA0
7-15
*On
128ENA1
7-15
*Off
ISBENA0
7-15
On
ISBENA1
7-15
Minimum (0 - 80) *0
128MIN##
7-15
Maximum (0 - 80) *80
128MAX##
7-15
*On
128APP1
7-15
Off
128APP0
7-16
Code 128 Code Page (*2)
128DCP##
7-16
Page
Default All GS1-128 Settings
GS1DFT
7-17
*On
GS1ENA1
7-17
Off
GS1ENA0
7-17
Minimum (1 - 80) *1
GS1MIN##
7-17
Maximum (0 - 80) *80
GS1MAX##
7-17
Default All
UPC-A Settings
UPADFT
7-17
Off
UPAENA0
7-18
*On
UPAENA1
7-18
Off
UPACKX0
7-17
*On
UPACKX1
7-18
UPC-A Number System
Off
UPANSX0
7-18
*On
UPANSX1
7-18
UPC-A 2 Digit Addenda
*Off
UPAAD20
7-18
On
UPAAD21
7-18
*Off
UPAAD50
7-18
On
UPAAD51
7-18
UPC-A Addenda Required
*Not Required
UPAARQ0
7-19
Required
UPAARQ1
7-19
UPC-A Addenda
Separator
Off
UPAADS0
7-19
*On
UPAADS1
7-19
UPC-A/EAN-13 with Extended
Coupon Code
*Off
CPNENA0
7-19
Allow Concatenation
CPNENA1
7-19
Require Concatenation
CPNENA2
7-19
GS1 Output Off
CPNGS10
7-20
GS1 Output On
CPNGS11
7-20
Default All UPC-E
Settings
UPEDFT
7-20
Off
UPEEN00
7-20
*On
UPEEN01
7-20
*Off
UPEEXP0
7-20
On
UPEEXP1
7-20
Required
UPEARQ1
7-21
*Not Required
UPEARQ0
7-21
UPC-A 5 Digit Addenda
Coupon GS1 DataBar Output
UPC-E0
UPC-E0 Expand
UPC-E0 Addenda Required
10 - 16
Selection
UPC-E0 Addenda Separator
UPC-E0 Check Digit
UPC-E0 Number System
UPC-E0 Addenda
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
*On
UPEADS1
7-21
Off
UPEADS0
7-21
Off
UPECKX0
7-21
*On
UPECKX1
7-21
Off
UPENSX0
7-21
*On
UPENSX1
7-21
2 Digit Addenda On
UPEAD21
7-22
*2 Digit Addenda Off
UPEAD20
7-22
5 Digit Addenda On
UPEAD51
7-22
Page
*5 Digit Addenda Off
UPEAD50
7-22
*Off
UPEEN10
7-22
On
UPEEN11
7-22
Default All EAN/
JAN Settings
E13DFT
7-23
Off
E13ENA0
7-23
*On
E13ENA1
7-23
Off
E13CKX0
7-23
*On
E13CKX1
7-23
2 Digit Addenda On
E13AD21
7-24
*2 Digit Addenda Off
E13AD20
7-24
5 Digit Addenda On
E13AD51
7-24
*5 Digit Addenda Off
E13AD50
7-24
*Not Required
E13ARQ0
7-24
Required
E13ARQ1
7-24
EAN/JAN-13 Addenda
Separator
Off
E13ADS0
7-24
*On
E13ADS1
7-24
ISBN Translate
*Off
E13ISB0
7-25
On
E13ISB1
7-25
Default All EAN/
JAN 8 Settings
EA8DFT
7-25
Off
EA8ENA0
7-25
*On
EA8ENA1
7-25
Off
EA8CKX0
7-25
*On
EA8CKX1
7-25
*2 Digit Addenda Off
EA8AD20
7-26
2 Digit Addenda On
EA8AD21
7-26
*5 Digit Addenda Off
EA8AD50
7-26
5 Digit Addenda On
EA8AD51
7-26
UPC-E1
EAN/JAN-13
EAN/JAN-13 Check Digit
EAN/JAN-13 2 Digit Addenda
EAN/JAN-13 Addenda Required
EAN/JAN-8
EAN/JAN-8 Check Digit
EAN/JAN-8 Addenda
EAN/JAN-8 Addenda Required
EAN/JAN-8 Addenda
Separator
*Not Required
EA8ARQ0
7-26
Required
EA8ARQ1
7-26
Off
EA8ADS0
7-26
*On
EA8ADS1
7-26
10 - 17
Selection
MSI
MSI Check Character
MSI Message Length
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Default All MSI Settings
MSIDFT
7-27
*Off
MSIENA0
7-27
On
MSIENA1
7-27
*Validate Type 10, but Don’t Transmit
MSICHK0
7-27
Validate Type 10 and
Transmit
MSICHK1
7-27
Validate 2 Type 10 Chars, but Don’t
Transmit
MSICHK2
7-27
Validate 2 Type 10 Chars and Transmit
MSICHK3
7-27
Validate Type 10 then Type 11 Char, but
Don’t Transmit
MSICHK4
7-27
Validate Type 10 then Type 11 Char and
Transmit
MSICHK5
7-28
Disable MSI Check Characters
MSICHK6
7-28
Page
Minimum (4 - 48) *4
MSIMIN##
7-28
Maximum (4 - 48) *48
MSIMAX##
7-28
Default All
GS1 DataBar Omnidirectional Settings
RSSDFT
7-29
Off
RSSENA0
7-29
*On
RSSENA1
7-29
Default All GS1 DataBar Limited Settings
RSLDFT
7-29
Off
RSLENA0
7-29
*On
RSLENA1
7-29
Default All GS1 DataBar
Expanded Settings
RSEDFT
7-30
Off
RSEENA0
7-30
*On
RSEENA1
7-30
GS1 DataBar Expanded Msg.
Length
Minimum (4 - 74) *4
RSEMIN##
7-30
Maximum (4 - 74) *74
RSEMAX##
7-30
Codablock A
Default All Codablock A Settings
CBADFT
7-30
*Off
CBAENA0
7-30
On
CBAENA1
7-30
Minimum (1 - 600) *1
CBAMIN####
7-31
Maximum (1 - 600) *600
CBAMAX####
7-31
Default All Codablock F Settings
CBFDFT
7-31
*Off
CBFENA0
7-31
On
CBFENA1
7-31
Minimum (1 - 2048) *1
CBFMIN####
7-31
Maximum (1 - 2048) *2048
CBFMAX####
7-31
Default All PDF417 Settings
PDFDFT
7-32
GS1 DataBar Omnidirectional
GS1 DataBar Limited
GS1 DataBar Expanded
Codablock A Msg. Length
Codablock F
Codablock F Msg. Length
PDF417
10 - 18
Selection
PDF417 Msg. Length
MacroPDF417
MicroPDF417
MicroPDF417 Msg. Length
GS1 Composite Codes
UPC/EAN Version
GS1 Composite Codes Msg. Length
GS1 Emulation
TCIF Linked Code 39
QR Code
QR Code Msg. Length
QR Code Append
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
*On
PDFENA1
7-32
Off
PDFENA0
7-32
Minimum (1-2750) *1
PDFMIN####
7-32
Maximum (1-2750) *2750
PDFMAX####
7-32
*On
PDFMAC1
7-32
Off
PDFMAC0
7-32
Page
Default All Micro PDF417 Settings
MPDDFT
7-33
On
MPDENA1
7-33
*Off
MPDENA0
7-33
Minimum (1-366) *1
MPDMIN###
7-33
Maximum (1-366) *366
MPDMAX###
7-33
On
COMENA1
7-33
*Off
COMENA0
7-33
On
COMUPC1
7-34
*Off
COMUPC0
7-34
Minimum (1-2435) *1
COMMIN####
7-34
Maximum (1-2435) *2435
COMMAX####
7-34
GS1-128 Emulation
EANEMU1
7-34
GS1 DataBar Emulation
EANEMU2
7-35
GS1 Code Expansion Off
EANEMU3
7-35
EAN8 to EAN13 Conversion
EANEMU4
7-35
*GS1 Emulation Off
EANEMU0
7-35
On
T39ENA1
7-35
*Off
T39ENA0
7-35
Default All QR Code Settings
QRCDFT
7-40
*On
QRCENA1
7-35
Off
QRCENA0
7-35
Minimum (1-7089) *1
QRCMIN####
7-36
Maximum (1-7089) *7089
QRCMAX####
7-36
*On
QRCAPP1
7-36
Off
QRCAPP0
7-36
QR Code Page
QR Code Page (*3)
QRCDCP##
7-36
Data Matrix
Default All Data Matrix Settings
IDMDFT
7-37
*On
IDMENA1
7-37
Off
IDMENA0
7-37
Data Matrix Msg. Length
Minimum (1-3116) *1
IDMMIN####
7-37
Maximum (1-3116) *3116
IDMMAX####
7-37
Data Matrix Append
*On
IDMAPP1
7-37
Off
IDMAPP0
7-37
Data Matrix Code Page
Data Matrix Code Page (*51)
IDMDCP##
7-38
MaxiCode
Default All MaxiCode Settings
MAXDFT
7-38
On
MAXENA1
7-38
*Off
MAXENA0
7-38
10 - 19
Selection
MaxiCode Msg. Length
Aztec Code
Aztec Code Msg. Length
Aztec Append
Aztec Code Page
Chinese Sensible (Han Xin) Code
Chinese Sensible (Han Xin) Code
Msg. Length
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Minimum (1-150) *1
MAXMIN###
7-38
Maximum (1-150) *150
MAXMAX###
7-38
Default All Aztec Code Settings
AZTDFT
7-39
*On
AZTENA1
7-39
Off
AZTENA0
7-39
Minimum (1-3832) *1
AZTMIN####
7-39
Maximum (1-3832) *3832
AZTMAX####
7-39
Page
On
AZTAPP1
7-39
*Off
AZTAPP0
7-39
Aztec Code Page (*51)
AZTDCP##
7-40
Default All Han Xin Code Settings
HX_DFT
7-40
On
HX_ENA1
7-40
*Off
HX_ENA0
7-40
Minimum (1-7833) *1
HX_MIN####
7-40
Maximum (1-7833) *7833
HX_MAX####
7-40
Default All China Post (Hong Kong 2 of 5)
Settings
CPCDFT
7-45
*Off
CPCENA0
7-45
Postal Codes - Linear
China Post (Hong Kong 2 of 5)
On
CPCENA1
7-45
China Post (Hong Kong 2 of 5) Msg.
Length
Minimum (2 - 80) *4
CPCMIN##
7-45
Maximum (2 - 80) *80
CPCMAX##
7-46
Korea Post
Default All Korea Post Settings
KPCDFT
7-46
*Off
KPCENA0
7-46
On
KPCENA1
7-46
Minimum (2 - 80) *4
KPCMIN##
7-46
Maximum (2 - 80) *48
KPCMAX##
7-46
Transmit Check Digit
KPCCHK1
7-46
*Don’t Transmit Check Digit
KPCCHK0
7-46
2D Postal Codes
*Off
POSTAL0
7-46
Single 2D Postal Codes
Australian Post On
POSTAL1
7-41
British Post On
POSTAL7
7-41
Canadian Post On
POSTAL30
7-41
Intelligent Mail Bar Code On
POSTAL10
7-41
Japanese Post On
POSTAL3
7-41
KIX Post On
POSTAL4
7-41
Planet Code On
POSTAL5
7-41
Postal-4i On
POSTAL9
7-41
Postnet On
POSTAL6
7-42
Korea Post Msg. Length
Korea Post Check Digit
Postal Codes - 2D
10 - 20
Selection
Combination 2D Postal Codes
Planet Code Check Digit
Postnet Check Digit
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Postnet with B and B’ Fields On
POSTAL11
7-42
InfoMail On
POSTAL2
7-42
InfoMail and British Post On
POSTAL8
7-42
Intelligent Mail Bar Code and Postnet with B
and B’ Fields On
POSTAL20
7-42
Postnet and Postal-4i On
POSTAL14
7-42
Postnet and Intelligent Mail Bar Code On
POSTAL16
7-42
Postal-4i and Intelligent Mail Bar Code On
POSTAL17
7-42
Postal-4i and Postnet with B and B’ Fields
On
POSTAL19
7-42
Planet and Postnet On
POSTAL12
7-42
Planet and Postnet with B and B’ Fields On
POSTAL18
7-43
Planet and Postal-4i On
POSTAL13
7-43
Planet and Intelligent Mail Bar Code On
POSTAL15
7-43
Planet, Postnet, and Postal-4i On
POSTAL21
7-43
Planet, Postnet, and Intelligent Mail Bar
Code On
POSTAL22
7-43
Planet, Postal-4i, and Intelligent Mail Bar
Code On
POSTAL23
7-43
Postnet, Postal-4i, and Intelligent Mail Bar
Code On
POSTAL24
7-43
Planet, Postal-4i, and Postnet with B and B’
Fields On
POSTAL25
7-43
Planet, Intelligent Mail Bar Code, and
Postnet with B and B’ Fields On
POSTAL26
7-43
Postal-4i, Intelligent Mail Bar Code, and
Postnet with B and B’ Fields On
POSTAL27
7-43
Planet, Postal-4i, Intelligent Mail Bar Code,
and Postnet On
POSTAL28
7-44
Planet, Postal-4i, Intelligent Mail Bar Code,
and Postnet with B and B’ Fields On
POSTAL29
7-44
Transmit
PLNCKX1
7-44
*Don’t Transmit
PLNCKX0
7-44
Page
Transmit
NETCKX1
7-44
*Don’t Transmit
NETCKX0
7-44
Bar Output
AUSINT0
7-45
Numeric N Table
AUSINT1
7-45
Alphanumeric C Table
AUSINT2
7-45
Combination N and C Tables
AUSINT3
7-45
PRECA2,BK2995C80!
9-1
Show Decoder Revision
REV_DR
9-1
Show Scan Driver Revision
REV_SD
9-1
Show Software Revision
REVINF
9-1
Show Data Format
DFMBK3?
9-1
Australian Post Interpretation
Utilities
Add Code I.D. Prefix to All Symbologies (Temporary)
10 - 21
Selection
Resetting the Factory Defaults
10 - 22
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Remove Custom Defaults
DEFOVR
9-3
Activate Defaults
DEFALT
9-3
Page
11
Product Specifications
Voyager 1450g Scanner Product Specifications
Parameter
Specification
Mechanical
Height
3.23 in. (82mm)
Length
2.45 in. (62mm)
Width
6.65 in. (169mm)
Weight
4.6 oz. (130g)
Electrical
Input Voltage
4.0 - 5.5VDC
Operating Power
2W (400mA @ 5VDC)
Standby Power
.45W (90mA @ 5VDC)
Illumination LED
White emitting color
Aiming
624nm peak wavelength
Environmental
Operating Temperature
32°F to 104°F (0°C to 40°C)
Storage Temperature
-4°F to 140°F (-20°C to 60°C)
Humidity
5 to 95% non-condensing
Drop
Operational after 30 drops to concrete from 5 ft. (1.5m)
Environmental Sealing
IP40
Light Levels
0 to 100,000 lux (9,290 foot-candles)
ESD
15kV Air, 8kV contact
Image
Image Size
640 x 480 pixels
Scan Performance
Pitch, Skew
+60°, +70°
Motion Tolerance:
Presentation Mode
up to 10cm per second for 13 mil UPC
Symbol Contrast
35%
Depth of Field
Typical Performance
5 mil Code 39
45 - 107mm (1.8 - 4.2 in.)
13 mil UPC-A
37 - 260mm (1.4 - 10.2 in.)
20 mil Code 39
42 - 360mm (1.6 - 14.2 in.)
6.7 mil PDF417
42 - 107mm (1.6 - 4.2 in.)
10mil Data Matrix
42 - 107mm (1.6 - 4.2 in.)
20mil QR Code
32 - 210mm (1.2 - 8.3 in.)
Guaranteed Performance
5 mil Code 39
57 - 102mm (2.2 - 4.0 in.)
13 mil UPC-A
41 - 207mm (1.6 - 8.1 in.)
20 mil Code 39
45 - 300mm (1.8 - 11.8 in.)
6.7 mil PDF417
45 - 100mm (1.8 - 3.9 in.)
10mil Data Matrix
50 - 98mm (2.0 - 3.8 in.)
20mil QR Code
35 - 190mm (1.4 - 7.5 in.)
11 - 1
Voyager 1452g Cordless Scanner Product Specifications
Parameter
Specification
Mechanical
Height
6.8 in. (17.3cm)
Length
3.2 in. (8.2cm)
Width
2.5 in. (6.2cm)
Weight
7.3 oz. (210g)
Electrical
Battery:
Lithium Ion
2400 mAH lithium-ion
Number of Scans
Up to 40,000 per charge
Expected Hours of Operation
14
Expected Charge Time
4.5 hours
Illumination LED
White emitting color
Aiming
624nm peak wavelength
Radio
Frequency
2.4 to 2.5 GHz (ISM Band) Frequency Hopping Bluetooth v.2.1
Range
33 ft. (10 m) typical
Data Rate
Up to 1 MBps
Environmental
Operating Temperature
41 F to 104 F (5 C to 40 C)
Storage Temperature (with battery)
-4F to 95F (-20C to 35C) storage for 90 days
-4F to 68F (-20C to 20C) storage for 1 year
Humidity
Up to 95% non-condensing
Drop
Operational after 30 drops to concrete from 5 ft. (1.5 m)
Environmental Sealing
IP42
Vibration
Withstands 5G peak from 5 to 300 Hz
ESD
12kV Air, 8kV contact
Image
Image Size
640 x 480 pixels
Scan Performance
Pitch, Skew
+60°, +70°
Motion Tolerance:
Presentation Mode
up to 10cm per second for 13 mil UPC
Symbol Contrast
35%
Depth of Field
Typical Performance
5 mil Code 39
45 - 107mm (1.8 - 4.2 in.)
13 mil UPC
37 - 260mm (1.4 - 10.2 in.)
20 mil Code 39
42 - 360mm (1.6 - 14.2 in.)
6.7 mil PDF417
42 - 107mm (1.6 - 4.2 in.)
10mil Data Matrix
42 - 107mm (1.6 - 4.2 in.)
20mil QR Code
32 - 210mm (1.2 - 8.3 in.)
Guaranteed Performance
5 mil Code 39
57 - 102mm (2.2 - 4.0 in.)
13 mil UPC-A
41 - 207mm (1.6 - 8.1 in.)
11 - 2
Parameter
Specification
20 mil Code 39
45 - 300mm (1.8 - 11.8 in.)
6.7 mil PDF417
45 - 100mm (1.8 - 3.9 in.)
10mil Data Matrix
50 - 98mm (2.0 - 3.8 in.)
20mil QR Code
35 - 190mm (1.4 - 7.5 in.)
*Storage outside of this temperature range could be detrimental to battery life.
CCB01-010BT Charge Base Product Specifications
Parameter
Specification
Dimensions (Typical):
Height
3.2 inches (8.13cm)
Length
5.19 inches (13.18cm)
Width
3.98 inches (10.11cm)
Weight
Voltage:
6.3 oz (179g)
4.5 to 5.5 volts
Current Draw:
Host Terminal Port
500mA
Aux Power Port
1A
Charge Time
5 hours
Radio:
Frequency
2.4 to 2.5 GHz (ISM Band) Frequency Hopping Bluetooth v.2.1
Range
33 ft. (10 m) typical
Data Rate
Up to 1 MBps
Temperature Ranges:
Operating
32 F to +122 F (0 C to +50 C)
Battery Charge
41 F to +104 F (5 C to +40 C)
Storage
-40 F to +158 F (-40 C to +70 C)
Humidity
Up to 95% non-condensing
Mechanical Drop
Operational after 50 drops from 3.28 feet
(1 m) to concrete
Vibration
5G Peak from 22Hz to 300Hz
ESD Sensitivity
Up to 15kV direct air
Up to 8 kV indirect coupling plane
Sealant Rating
IP41
11 - 3
Standard Cable Pinouts
Note: The following pin assignments are not compatible with Honeywell legacy products. Use of a cable with improper pin
assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage
not covered by your warranty.
Keyboard Wedge
10 Pin RJ41 Modular Plug
1
2
3
4
5
6
7
8
9
10
Cable shield
Cable select
Supply ground
Terminal data
Terminal clock
Keyboard clock
+5V power
Keyboard data
Serial Output
10 Pin RJ41 Modular Plug
1
2
3
4
5
6
7
8
9
10
Cable shield
Cable select
Supply ground
Transmit data
Receive data - serial data to scanner
CTS
+5V power
RTS
USB
10 Pin Modular Plug
1
2
3
4
5
6
7
8
9
10
11 - 4
Cable shield
Cable select
Supply ground
+5V power
Data +
Data -
RS485 Output
10 Pin RJ41 Modular Plug
Note: RS485 signal conversion is performed in the cable.
1
2
3
4
5
6
7
8
9
10
Cable shield
Cable select
Supply ground
Transmit data
Receive data - serial data to scanner
+5V power
Transmit Enable
11 - 5
Required Safety Labels
Voyager 1450g/1452g Scanner
Laser Output
Part Number,
Serial Number
Laser Label,
and Revision
Information
location
11 - 6
Laser Safety
information
CCB01-010BT Base
Part Number,
Serial
Number and
Revision
Information
location
Compliance
Label
locations
11 - 7
11 - 8
12
Maintenance
Repairs
Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized
service center (see Customer Support on page 13-1).
Maintenance
Your device provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the
following periodic checks ensure dependable operation:
Cleaning the Device
Reading performance may degrade if the scanner’s window is not clean. If the window is visibly dirty, or if the scanner isn’t
operating well, clean the window with a soft cloth or lens tissue dampened with water (or a mild detergent- water solution).
If a detergent solution is used, rinse with a clean lens tissue dampened with water only.
The scanner and base’s housing may also be cleaned the same way.
!
Caution:
Do not submerge the scanner in water. The scanner’s
housing is not watertight.
Do not use abrasive wipes or tissues on the scanner’s
window – abrasive wipes may scratch the window. Never
use solvents (e.g., alcohol or acetone) on the housing or
window – solvents may damage the finish or the window.
Inspecting Cords and Connectors
Inspect the interface cable and connector for wear or other signs of damage. A badly worn cable or damaged connector
may interfere with scanner operation. Contact your distributor for information about cable replacement. Cable replacement
instructions are on page 12-1.
Replacing Cables in Corded Scanners
The standard interface cable is attached to the scanner with an 10-pin modular connector. When properly seated, the connector is held in the scanner’s handle by a flexible retention tab. The interface cable is designed to be field replaceable.
• Order replacement cables from Honeywell or from an authorized distributor.
• When ordering a replacement cable, specify the cable part number of the original interface cable.
12 - 1
Replacing a Corded Scanner Interface Cable
1. Turn the power to the host system OFF.
2. Disconnect the scanner’s cable from the terminal or computer.
3. Locate the small hole on the back of the scanner’s handle. This is the cable release.
4. Straighten one end of a paper clip.
5. Insert the end of the paper clip into the small hole and press in. This depresses the retention
tab, releasing the connector. Pull the connector out while maintaining pressure on the paper
clip, then remove the paper clip.
6. Replace with the new cable.
Insert the connector into the opening and press firmly. The connector is keyed to go in only
one way, and will click into place.
Replacing Cables and Batteries in Cordless Systems
Cable
Release
Replacing an Interface Cable in a Base
1. Turn the power to the host system OFF.
2. Disconnect the base’s cable from the terminal or computer.
3. Turn the base upside down.
4. Pull the connector out while maintaining pressure on the connector release clip.
CCB01-010BT Base :
5. Replace with the new cable.
Insert the connector into the opening and press firmly. The connector is keyed to go in only one way, and will click into
place.
12 - 2
Changing a Cordless Scanner Battery
1. Use the hinged wire or a flat head screwdriver to remove the screw from the
end cap.
2. Remove the end cap and remove the battery from the handle.
3. Insert replacement battery.
4. Replace end cap and screw it back on.
Troubleshooting a Corded Scanner
The scanner automatically performs self-tests whenever you turn it on. If your
scanner is not functioning properly, review the following Troubleshooting Guide to
try to isolate the problem.
End Cap
Is the power on? Is the aimer on?
If the aimer isn’t illuminated, check that:
• The cable is connected properly.
• The host system power is on (if external power isn’t used).
• The trigger works.
Is the scanner having trouble reading your symbols?
If the scanner isn’t reading symbols well, check that the scanner window is clean and that the symbols:
• Aren’t smeared, rough, scratched, or exhibiting voids.
• Aren’t coated with frost or water droplets on the surface.
• Are enabled in the scanner or in the decoder to which the scanner connects.
Is the bar code displayed but not entered?
The bar code is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or
the Tab key, for example).
• You need to program a suffix. Programming a suffix enables the scanner to output the bar code data plus the key you
need (such as “CR”) to enter the data into your application. Refer to Prefix/Suffix Overview beginning on page 5-1 for
further information.
Does the scanner read the bar code incorrectly?
If the scanner reads a bar code, but the data is not displayed correctly on the host screen:
• The scanner may not be programmed for the appropriate terminal interface.
For example, you scan “12345” and the host displays “@es%.”
Reprogram the scanner with the correct Plug and Play bar code. See Programming the Interface beginning on page 2-1.
• The scanner may not be programmed to output your bar code data properly.
For example, you scan “12345” and the host displays “A12345B.”
Reprogram the scanner with the proper symbology selections. See Chapter 7.
The scanner won’t read your bar code at all.
1. Scan the sample bar codes in the back of this manual. If the scanner reads the sample bar codes, check that your bar
code is readable.
Verify that your bar code symbology is enabled (see Chapter 7).
If the scanner still can’t read the sample bar codes, scan All Symbologies (page 7-1).
If you aren’t sure what programming options have been set in the scanner, or if you want the factory default settings
restored, refer to Resetting the Custom Defaults on page 10-3.
Troubleshooting a Cordless System
Troubleshooting a Base
Note: Visit the Services and Support section of our website (www.honeywellaidc.com) to check for the latest software for
both the scanner and the base.
12 - 3
If your base is not functioning properly, review the following troubleshooting guidelines to try to isolate the problem.
Is the red LED on?
If the red LED isn’t illuminated, check that:
• The power cable is connected properly and there is power at the power source.
• The host system power is on (if external power isn’t used).
Is the green LED on?
If the green LED isn’t illuminated, check that:
•
•
•
•
The scanner is correctly placed in the base.
There is external power or 12 volt host power.
Charge mode is turned on. (See "Beeper and LED Sequences and Meaning" on page 3-5)
The battery is not bad or deeply discharged. In some cases, the scanner’s battery may trickle charge to bring it into an
acceptable level and then transition to a normal charge cycle.
Troubleshooting a Cordless Scanner
Note: Make sure that your scanner’s battery is charged.
Visit the Services and Support section of our website (www.honeywellaidc.com) to check for the latest software for
both the scanner and the base or Access Point.
Is the scanner having trouble reading your symbols?
If the scanner isn’t reading symbols well, check that the symbols:
• Aren’t smeared, rough, scratched, or exhibiting voids.
• Aren’t coated with frost or water droplets on the surface.
• Are enabled in the base or Access Point to which the scanner connects.
Is the bar code displayed but not entered into the application?
The bar code is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or
the Tab key, for example).
• You need to program a suffix. Programming a suffix enables the scanner to output the bar code data plus the key you
need (such as “CR”) to enter the data into your application. Refer to Prefix/Suffix Overview on page 5-1 for further
information.
Does the scanner read the bar code incorrectly?
If the scanner reads a bar code, but the data is not displayed correctly on the host screen:
• The base or Access Point may not be programmed for the appropriate terminal interface. For example, you scan “12345”
and the host displays “@es%.”
Reprogram the base/Access Point with the correct Plug and Play bar code. See Programming the Interface beginning on
page 2-1.
• The bas or Access Pointe may not be programmed to output your bar code data properly. For example, you scan “12345”
and the host displays “A12345B.”
Reprogram the base/Access Point with the proper symbology selections. See Chapter 7.
The scanner won’t read your bar code at all.
• Scan the sample bar codes in the back of this manual. If the scanner reads the sample bar codes, check that your bar
code is readable.
Verify that your bar code symbology is enabled (see Chapter 7).
If the scanner still can’t read the sample bar codes, scan All Symbologies on page 7-1.
12 - 4
13
Customer Support
Technical Assistance
If you need assistance installing or troubleshooting your device, please contact us by using one of the methods below:
Knowledge Base: www.hsmknowledgebase.com
Our Knowledge Base provides thousands of immediate solutions. If the Knowledge Base cannot help, our Technical Support
Portal (see below) provides an easy way to report your problem or ask your question.
Technical Support Portal: www.hsmsupportportal.com
The Technical Support Portal not only allows you to report your problem, but it also provides immediate solutions to your technical issues by searching our Knowledge Base. With the Portal, you can submit and track your questions online and send and
receive attachments.
Web form: www.hsmcontactsupport.com
You can contact our technical support team directly by filling out our online support form. Enter your contact details and the
description of the question/problem.
Telephone: www.honeywellaidc.com/locations
For our latest contact information, please check our website at the link above.
Product Service and Repair
Honeywell International Inc. provides service for all of its products through service centers throughout the world. To obtain
warranty or non-warranty service, please visit www.honeywellaidc.com and select Support > Contact Service and Repair to
see your region's instructions on how to obtain a Return Material Authorization number (RMA #). You should do this prior to
returning the product.
Limited Warranty
Honeywell International Inc. ("HII") warrants its products to be free from defects in materials and workmanship and to conform to
HII’s published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any
HII product which is (i) improperly installed or used; (ii) damaged by accident or negligence, including failure to follow the proper
maintenance, service, and cleaning schedule; or (iii) damaged as a result of (A) modification or alteration by the purchaser or
other party, (B) excessive voltage or current supplied to or drawn from the interface connections, (C) static electricity or electrostatic discharge, (D) operation under conditions beyond the specified operating parameters, or (E) repair or service of the product by anyone other than HII or its authorized representatives.
This warranty shall extend from the time of shipment for the duration published by HII for the product at the time of purchase
("Warranty Period"). Any defective product must be returned (at purchaser’s expense) during the Warranty Period to HII factory
or authorized service center for inspection. No product will be accepted by HII without a Return Materials Authorization, which
may be obtained by contacting HII. In the event that the product is returned to HII or its authorized service center within the
Warranty Period and HII determines to its satisfaction that the product is defective due to defects in materials or workmanship,
HII , at its sole option, will either repair or replace the product without charge, except for return shipping to HII.
EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE FOREGOING WARRANTY IS IN LIEU OF ALL
OTHER COVENANTS OR WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR WRITTEN, INCLUDING, WITHOUT
LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR
NON-INFRINGEMENT.
HII’S RESPONSIBILITY AND PURCHASER’S EXCLUSIVE REMEDY UNDER THIS WARRANTY IS LIMITED TO THE
REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT WITH NEW OR REFURBISHED PARTS. IN NO EVENT
SHALL HII BE LIABLE FOR INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, AND, IN NO EVENT, SHALL ANY
LIABILITY OF HII ARISING IN CONNECTION WITH ANY PRODUCT SOLD HEREUNDER (WHETHER SUCH LIABILITY
ARISES FROM A CLAIM BASED ON CONTRACT, WARRANTY, TORT, OR OTHERWISE) EXCEED THE ACTUAL AMOUNT
PAID TO HII FOR THE PRODUCT. THESE LIMITATIONS ON LIABILITY SHALL REMAIN IN FULL FORCE AND EFFECT
13 - 1
EVEN WHEN HII MAY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES, LOSSES, OR DAMAGES. SOME
STATES, PROVINCES, OR COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
All provisions of this Limited Warranty are separate and severable, which means that if any provision is held invalid and unenforceable, such determination shall not affect the validity of enforceability of the other provisions hereof. Use of any peripherals
not provided by the manufacturer may result in damage not covered by this warranty. This includes but is not limited to: cables,
power supplies, cradles, and docking stations. HII extends these warranties only to the first end-users of the products. These
warranties are non-transferable.
The duration of the limited warranty for the Voyager 1450g scanner is five (5) years.
The duration of the limited warranty for the Voyager 1452g scanner is three (3) years.
The duration of the limited warranty for the CCB01-010BT Charge Base is three (3) years.
The duration of the limited warranty for the Voyager 1452 battery is one (1) year.
13 - 2
A
Reference Charts
Symbology Charts
Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for AIM
modifier character details.
Prefix/Suffix entries for specific symbologies override the universal (All Symbologies, 99) entry.
Refer to Data Editing beginning on page 5-1 and Data Formatting beginning on page 6-1 for information about using Code ID
and AIM ID.
Linear Symbologies
AIM
Symbology
ID
Possible modifiers
(m)
Honeywell
ID
All Symbologies
99
Codabar
]Fm
Code 11
]H3
Code 128
]Cm
Code 32 Pharmaceutical (PARAF)
]X0
Code 39 (supports Full ASCII mode)
]Am
TCIF Linked Code 39 (TLC39)
]L2
Code 93 and 93i
EAN
Hex
0-1
0, 1, 2, 4
0, 1, 3, 4, 5, 7
]Gm
0-9, A-Z,
a-m
]Em
0, 1, 3, 4
a
61
h
68
j
6A
<
3C
b
62
T
54
i
69
d
64
EAN-13 (including Bookland EAN)
]E0
d
64
EAN-13 with Add-On
]E3
d
64
EAN-13 with Extended Coupon Code
]E3
d
64
EAN-8
]E4
D
44
EAN-8 with Add-On
]E3
D
44
y
79
GS1
GS1 DataBar
]em
0
GS1 DataBar Limited
]em
{
7B
GS1 DataBar Expanded
]em
}
7D
GS1-128
]C1
I
49
2 of 5
China Post (Hong Kong 2 of 5)
]X0
Interleaved 2 of 5
]Im
Q
51
e
65
Matrix 2 of 5
]X0
m
6D
NEC 2 of 5
]X0
Y
59
f
66
f
66
g
67
c
63
Straight 2 of 5 IATA
]Rm
Straight 2 of 5 Industrial
]S0
MSI
]Mm
UPC
UPC-A
0, 1, 3
0, 1, 3
0, 1
0, 1, 2, 3, 8, 9, A, B, C
]E0
A-1
AIM
Symbology
ID
Possible modifiers
(m)
Honeywell
ID
Hex
UPC-A with Add-On
]E3
c
63
UPC-A with Extended Coupon Code
]E3
c
63
UPC-E
]E0
E
45
UPC-E with Add-On
]E3
E
45
UPC-E1
]X0
E
45
Add Honeywell Code ID
5C80
Add AIM Code ID
5C81
Add Backslash
5C5C
Batch mode quantity
5
35
2D Symbologies
AIM
Symbology
ID
Possible modifiers
(m)
Honeywell
ID
All Symbologies
99
Aztec Code
]zm
Chinese Sensible Code (Han Xin Code)
]X0
Codablock A
]O6
Codablock F
]Om
Code 49
Data Matrix
GS1
GS1 Composite
GS1 DataBar Omnidirectional
Hex
0-9, A-C
z
7A
H
48
0, 1, 4, 5, 6
V
56
0, 1, 4, 5, 6
q
71
]Tm
0, 1, 2, 4
l
6C
]dm
0-6
w
77
]em
0-3
y
79
]em
0-3
y
79
]em
0-3
y
79
MaxiCode
]Um
0-3
x
78
PDF417
]Lm
0-2
r
72
]Lm
0-5
R
52
]Qm
0-6
s
73
s
73
MicroPDF417
QR Code
Micro QR Code
]Qm
Postal Symbologies
AIM
Symbology
ID
Possible modifiers
(m)
Honeywell
ID
All Symbologies
Hex
99
Australian Post
]X0
A
41
British Post
]X0
B
42
A-2
AIM
Symbology
ID
Canadian Post
]X0
Possible modifiers
(m)
Honeywell
ID
Hex
C
43
China Post
]X0
Q
51
InfoMail
]X0
,
2c
Intelligent Mail Bar Code
]X0
M
4D
Japanese Post
]X0
J
4A
KIX (Netherlands) Post
]X0
K
4B
Korea Post
]X0
?
3F
Planet Code
]X0
L
4C
Postal-4i
]X0
N
4E
Postnet
]X0
P
50
ASCII Conversion Chart (Code Page 1252)
In keyboard applications, ASCII Control Characters can be represented in 3 different ways, as shown below. The CTRL+X function is OS and application dependent. The following table lists some commonly used Microsoft functionality. This table applies
to U.S. style keyboards. Certain characters may differ depending on your Country Code/PC regional settings.
Non-printable
characters
ASCII control
Keyboard Control + ASCII (CTRL+X) Mode
Windows Mode Control + X Mode On (KBDCAS2)
DEC
HEX
Char
Control + X Mode Off (KBDCAS0)
CTRL + X
0
00
NUL
Reserved
CTRL+ @
1
01
SOH
NP Enter
CTRL+ A
Select all
2
02
STX
Caps Lock
CTRL+ B
Bold
3
03
ETX
ALT Make
CTRL+ C
Copy
4
04
EOT
ALT Break
CTRL+ D
Bookmark
5
05
ENQ
CTRL Make
CTRL+ E
Center
6
06
ACK
CTRL Break
CTRL+ F
Find
7
07
BEL
Enter / Ret
CTRL+ G
8
08
BS
(Apple Make)
CTRL+ H
History
9
09
HT
Tab
CTRL+ I
Italic
10
0A
LF
(Apple Break)
CTRL+ J
Justify
11
0B
VT
Tab
CTRL+ K
hyperlink
CTRL+ L
list,
left align
Delete
CTRL + X function
12
0C
FF
13
0D
CR
Enter / Ret
CTRL+ M
14
0E
SO
Insert
CTRL+ N
New
15
0F
SI
ESC
CTRL+ O
Open
16
10
DLE
F11
CTRL+ P
Print
17
11
DC1
Home
CTRL+ Q
Quit
18
12
DC2
PrtScn
CTRL+ R
19
13
DC3
Backspace
CTRL+ S
20
14
DC4
Back Tab
CTRL+ T
21
15
NAK
F12
CTRL+ U
22
16
SYN
F1
CTRL+ V
23
17
ETB
F2
CTRL+ W
Save
Paste
A-3
Non-printable
characters
ASCII control
Keyboard Control + ASCII (CTRL+X) Mode
Windows Mode Control + X Mode On (KBDCAS2)
DEC
HEX
Char
Control + X Mode Off (KBDCAS0)
CTRL + X
24
18
CAN
F3
CTRL+ X
25
19
EM
F4
CTRL+ Y
26
1A
SUB
F5
CTRL+ Z
27
1B
ESC
F6
CTRL+ [
28
1C
FS
F7
CTRL+ \
29
1D
GS
F8
CTRL+ ]
30
1E
RS
F9
CTRL+ ^
31
1F
US
F10
CTRL+ -
127
7F
⌂
NP Enter
CTRL + X function
Lower ASCII Reference Table
Note: Windows Code page 1252 and lower ASCII use the same characters.
Printable Characters
DEC
HEX
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
A-4
Character
!
"
#
$
%
&
'
(
)
*
+
,
.
/
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
DEC
HEX
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
Character
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
DEC
HEX
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
Character
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
⌂
Extended ASCII Characters
DEC
HEX
CP 1252
ASCII
Alternate Extended
PS2 Scan Code
128
80
€
Ç
up arrow ↑
0x48
129
81
ü
down arrow ↓
0x50
130
82
‚
é
right arrow →
0x4B
131
83
ƒ
â
left arrow ←
0x4D
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
90
91
92
93
94
95
96
97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
AF
B0
B1
B2
„
…
†
‡
ˆ
‰
Š
‹
Œ
ä
à
å
ç
ê
ë
è
ï
î
ì
Ä
Å
É
æ
Æ
ô
ö
ò
û
ù
ÿ
Ö
Ü
¢
£
¥
₧
ƒ
á
í
ó
ú
ñ
Ñ
ª
º
¿
⌐
¬
½
¼
¡
«
»
░
▒
▓
Insert
Delete
Home
End
Page Up
Page Down
Right ALT
Right CTRL
Reserved
Reserved
Numeric Keypad Enter
Numeric Keypad /
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
Numeric Keypad +
Numeric Keypad Numeric Keypad *
Caps Lock
Num Lock
Left Alt
Left Ctrl
Left Shift
Right Shift
Print Screen
Tab
Shift Tab
Enter
Esc
Alt Make
Alt Break
Control Make
Control Break
Alt Sequence with 1 Character
Ctrl Sequence with 1 Character
0x52
0x53
0x47
0x4F
0x49
0x51
0x38
0x1D
n/a
n/a
0x1C
0x35
0x3B
0x3C
0x3D
0x3E
0x3F
0x40
0x41
0x42
0x43
0x44
0x57
0x58
0x4E
0x4A
0x37
0x3A
0x45
0x38
0x1D
0x2A
0x36
n/a
0x0F
0x8F
0x1C
0x01
0x36
0xB6
0x1D
0x9D
0x36
0x1D
Ž
‘
’
“
”
•
–
—
˜
™
š
›
œ
ž
Ÿ
¡
¢
£
¤
¥
¦
§
¨
©
ª
«
¬
®
¯
°
±
²
A-5
Extended ASCII Characters (Continued)
DEC
HEX
CP 1252
ASCII
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
B3
B4
B5
B6
B7
B8
B9
BA
BB
BC
BD
BE
BF
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
³
´
µ
¶
·
¸
¹
º
»
¼
½
¾
¿
À
Á
Â
Ã
Ä
Å
Æ
Ç
È
É
Ê
Ë
Ì
Í
Î
Ï
Ð
Ñ
Ò
Ó
Ô
Õ
Ö
×
Ø
Ù
Ú
Û
Ü
Ý
Þ
ß
à
á
â
ã
ä
å
æ
│
┤
╡
╢
╖
╕
╣
║
╗
╝
╜
╛
┐
└
┴
┬
├
─
í
╞
╟
╚
╔
╩
╦
╠
═
╬
╧
╨
╤
╥
╙
╘
╒
╓
╫
╪
┘
┌
█
▄
▌
▐
▀
α
ß
Γ
π
Σ
σ
µ
A-6
Alternate Extended
PS2 Scan Code
Extended ASCII Characters (Continued)
DEC
HEX
CP 1252
ASCII
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
ç
è
é
ê
ë
ì
í
î
ï
ð
ñ
ò
ó
ô
õ
ö
÷
ø
ù
ú
û
ü
ý
þ
ÿ
τ
Φ
Θ
Ω
δ
∞
φ
ε
∩
≡
±
≥
≤
⌠
⌡
÷
≈
°
·
·
√
ⁿ
²
■
Alternate Extended
PS2 Scan Code
ISO 2022/ISO 646 Character Replacements
Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, select the code page with which the bar codes were created. The data characters should
then appear properly.
Code Page Selection Method/Country
Standard
Keyboard Country
Honeywell Code Page
Option
United States
(standard ASCII)
ISO/IEC 646-IRV
n/a
1
Automatic National Character
Replacement
ISO/IEC 2022
n/a
2 (default)
Binary Code page
n/a
n/a
3
Default “Automatic National Character replacement” will select the below Honeywell Code Page options for Code128, Code
39 and Code 93.
United States
ISO/IEC 646-06
0
1
Canada
ISO /IEC 646-121
54
95
Canada
ISO /IEC 646-122
18
96
Japan
ISO/IEC 646-14
28
98
China
ISO/IEC 646-57
92
99
Great Britain (UK)
ISO /IEC 646-04
7
87
France
ISO /IEC 646-69
3
83
A-7
Code Page Selection Method/Country
Standard
Keyboard Country
Honeywell Code Page
Option
Germany
ISO/IEC646-21
4
84
Switzerland
ISO /IEC 646-CH
6
86
Sweden / Finland (extended Annex C)
ISO/IEC 646-11
2
82
Ireland
ISO /IEC 646-207
73
97
Denmark
ISO/IEC 646-08
8
88
Norway
ISO/IEC 646-60
9
94
Italy
ISO/IEC 646-15
5
85
Portugal
ISO/IEC 646-16
13
92
Spain
ISO/IEC 646-17
10
90
Spain
ISO/IEC 646-85
51
91
64
91
92
93
94
96
123
124
125
126
Hex
23
24
40
5B
5C
5D
5E
60
7B
7C
7D
7E
US
0
1
#
$
@
[
\
]
^
`
{
|
}
~
CA
54
95
#
$
à
â
ç
ê
î
ô
é
ù
è
û
CA
18
96
#
$
à
â
ç
ê
É
ô
é
ù
è
û
JP
28
98
#
$
@
[
¥
]
^
`
{
|
}
⎯
CN
92
99
#
¥
@
[
\
]
^
`
{
|
}
⎯
GB
7
87
£
$
@
[
\
]
^
`
{
|
}
˜
FR
3
83
£
$
à
°
ç
§
^
µ
é
ù
è
¨
DE
4
84
#
$
§
Ä
Ö
Ü
^
`
ä
ö
ü
ß
CH
6
86
ù
$
à
é
ç
ê
î
ô
ä
ö
ü
û
SE/FI
2
82
#
¤
É
Ä
Ö
Å
Ü
é
ä
ö
å
ü
DK
8
88
#
$
@
Æ
Ø
Å
^
`
æ
ø
å
˜
NO
9
94
#
$
@
Æ
Ø
Å
^
`
æ
ø
å
¨
IE
73
97
£
$
Ó
É
Í
Ú
Á
ó
é
í
ú
á
IT
5
85
£
$
§
°
ç
é
^
ù
à
ò
è
ì
PT
13
92
#
$
§
Ã
Ç
Õ
^
`
ã
ç
õ
°
ES
10
90
#
$
§
¡
Ñ
¿
^
`
°
ñ
ç
˜
ES
51
91
#
$
∙
¡
Ñ
Ç
¿
`
´
ñ
ç
¨
Honeywell
CodePage
36
Country Keyboard
35
COUNTRY
Dec
A-8
ISO / IEC 646 National Character Replacements
Unicode Key Maps
6E
70 71 72 73
74 75 76 77
78 79 7A 7B
7C 7D 7E
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F
10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D
1E 1F 20 21 22 23 24 25 26 27 28 29 2B
4B 50 55
4C 51 56
2C 2E 2F 30 31 32 33 34 35 36 37
39
3D
3A 3B 3C
3E 3F 38 40
53
4F 54 59
5A 5F
5B 60
5C 61
5D 62
63
64 69
65
6A
66
67
6C
68
5A 5F
5B 60
5C 61
5D 62
63
64 69
65
6A
66
67
6C
68
104 Key U.S. Style Keyboard
6E
70 71 72 73
74 75 76 77
78 79 7A 7B
7C 7D 7E
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F
10 11 12 13 14 15 16 17 18 19 1A 1B 1C 2B
1E 1F 20 21 22 23 24 25 26 27 28 29 2A
4B 50 55
4C 51 56
2C 2D 2E 2F 30 31 32 33 34 35 36 37
39
3D
3A 3B 3C
3E 3F 38 40
53
4F 54 59
105 Key European Style Keyboard
A-9
A - 10
Sample Symbols
UPC-A
Interleaved 2 of 5
0 123456 7890
1234567890
EAN-13
9 780330 290951
Code 128
Code 128
Code 39
BC321
Codabar
A13579B
Code 93
123456-9$
Straight 2 of 5 Industrial
123456
Matrix 2 of 5
6543210
GS1 DataBar
(01)00123456789012
PDF417
Car Registration
Data Matrix
Test Symbol
QR Code
Aztec
Numbers
Package Label
MaxiCode
Micro PDF417
Test Message
Test Message
Postnet
Zip Code
4-CB (4-State Customer Bar Code)
01,234,567094,987654321,01234567891
ID-tag (UPU 4-State)
J18CUSA8E6N062315014880T
Programming Chart
0
1
2
3
4
5
6
7
8
9
Programming Chart
A
B
C
D
E
F
Save
Discard
Reset
Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or
digits, and Save again.
Honeywell Scanning & Mobility
9680 Old Bailes Road
Fort Mill, SC 29707
www.honeywellaidc.com
VG1450-UG Rev A
12/14
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Author : Honeywell Scanning & Mobility Create Date : 2014:12:16 10:08:19Z Keywords : "Voyager 1400g, Voyager 1452g, User’s Guide, Honeywell" Modify Date : 2014:12:16 11:16:19-05:00 Language : en XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Creator Tool : FrameMaker 12.0.3 Metadata Date : 2014:12:16 11:16:19-05:00 Format : application/pdf Description : User’s Guide for Voyager 1400g/1452g Title : Voyager 1400g/1452g Series Area-Imaging Scanner User’s Guide Creator : Honeywell Scanning & Mobility Subject : Voyager 1400g, Voyager 1452g, User’s Guide, Honeywell Producer : Acrobat Distiller 11.0 (Windows) Document ID : uuid:b08c7b88-4053-4b40-9411-55db5fa1a5b4 Instance ID : uuid:b574da8e-0f64-425c-9d83-66419bf40ad4 Page Mode : UseOutlines Page Count : 206EXIF Metadata provided by EXIF.tools