Honeywell 202151TXR Thermostat User Manual E527 Datasheet v1 2 DS
INNCOM International Inc. Thermostat E527 Datasheet v1 2 DS
Manual.pdf
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1806069 |
| Application ID | opolCTevrGumONzT95BZzg== |
| Document Description | Manual.pdf |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 68.41kB (855132 bits) |
| Date Submitted | 2012-10-02 00:00:00 |
| Date Available | 2012-10-02 00:00:00 |
| Creation Date | 2012-10-01 08:39:48 |
| Producing Software | GPL Ghostscript 8.15 |
| Document Lastmod | 2012-10-01 09:26:38 |
| Document Title | Microsoft Word - E527 Datasheet v1.2 DS.doc |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | mahussain |
Confidential Copyright © 2012 INNCOM e527 Datasheet Overview Like the larger e528, the compact, low profile e527 thermostat takes advantage of component end-of-life to redesign hardware and produce a more efficient, lower cost device. With onboard radio and RS485 connection and an added CDS light sensor, the e527 maintains its position as an integral part of the INNCOM Integrated Room Automation System (IRAS) and a property’s Energy Management System (EMS). Features In an EMS, the e527 controls room heating and cooling using occupancy data collected from motion detectors and door switches and can be networked to the property’s central management system. As an IRAS device, the e527 can communicate with devices within a room and function as a room gateway device towards the mesh network. Figure 1 E527 • British gang mounting (American gang mounting with optional frame) • Accurate temperature measurement +/- 1 degree F • External temperature sensor support • Motion sensor for occupancy detection • RF transceiver (onboard 802.15.4, 2.4GHz radio) for wireless guestroom and backhaul network communications • RS485 for wired backhaul network communications • Photo sensor for light level detection Installation Requirements The e527 must be located on a partitioning interior wall, approximately 5' (1.5 m) above the floor, in a site of average temperature. It is important to ensure that the thermostat is located away from direct sunlight or radiant heat, air discharge grilles, stairwells, outside doors, steam or water pipes, warm air stacks, unheated/uncooled areas, or sources of electrical interference. The unit should not be placed on an outside wall or behind a door. The e527 is designed to be mounted on a standard British-style single-gang electrical box. For use with an American box, the e527 can be installed in an optional frame by means of two screws. Screws for attaching the optional frame and mounting the e527 are included. The device is shipped with a clear clamshell dust cover. E527 Datasheet Page 2 of 7 Headers Figure 2 E527 Front/Back and External Headers H1 H2 H3 H4 H5 H6 H7 H8 H9 ICP microprocessor programming Humidity sensor System interconnect PIR sensor ES1 RS485 network header (see pinout below) System 5 header (see pinout below) System interconnect External temperature control sensor (see pinout below) H6 Pinout Pin Function Comment Common GND 12VDC Min S5bus 10V 12V 14V Communication bus Dry Input Input RS485B RS485 Twisted Pair RS485A RS485 Twisted Pair Nom Max E527 Datasheet Page 3 of 7 H7 Pinout Pin Function Comment Common GND 12VDC Min S5bus 10V 12V 14V Communication bus Nom Max H9 Pinout Pin Function Comment Common GND Common External temp sensor GND Motion Detection The optional motion detector available on the e527 works in conjunction with the electronic door lock to determine room occupancy. If the door lock reports that the door has opened and closed and no motion is detected in the room for a set number of minutes, the e527 engages energy conservation setbacks. When motion is detected, the e527 returns to its occupied state. Also, the e527 reports occupancy changes to the central server. Figure 3 Motion Sensor Sensitivity E527 Datasheet Page 4 of 7 Network Communication INNCOM employs a Deep Mesh system to connect guestroom IRAS components to management and monitoring servers. Because networking infrastructure is embedded in the IRAS devices, command and reporting information packets can follow multiple network pathways, increasing communication efficiency and reliability at lower cost. Typically, a Deep Mesh network integrates 50–200 rooms per network segment*. INNCOM generally uses a wireless radio network, but a Deep Mesh system may be constructed using RS485 networks (topologies that merge RF and RS485 networks are also possible). 2.4GHz Wireless RF In a typical RF Deep Mesh network, an 802.15.4-based 2.4GHz radio-equipped IRAS device (most often a thermostat, such as the e527) acts as a room gateway for communication with the network. Data are propagated among the network nodes until terminated at edge routers that bridge traffic onto IP (Ethernet) networks towards the servers. The radio specifications are given in the table below: Performance 0dB RF Data Rate Antenna Type 250kbps SMT Indoor Range Outdoor/ RF line-of-sight range Transmit Power 70ft 540ft 1mW Receive Sensitivity Frequency Band -94.6dBm 2.4GHz Encryption Protocol Frequency Channels AES-128 802.15.4 11–26 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The network segment size depends on the facility’s layout, expected network traffic, and other environmental considerations. E527 Datasheet Page 5 of 7 This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. RS485 A Deep Mesh RS485 (DM485) network typically uses a CAT5-type wiring wired as a home-run or daisy-chain. The DM485 network is routed to a dedicated device in each guestroom. This device becomes the room gateway, which transfers information packets between the DM485 backbone and the in-room network. The in-room network can be either S5Bus or a local mesh formed with RF. Each DM485 network is operated by a B575 hardware running DM485 software. Refer to the H6 pinout table above for wiring instructions. Technical Specifications Power Requirements Thermostat Measurement Range Outdoor Air Temperature Display Display Resolution Standard Deadband Degrees C/Degrees F Display Ambient Operating Ambient Storage Dimensions Approvals 12VDC, 50mA 33 to 99 degrees F (1 to 37 degrees C) 0 to 99 degrees F (-18 to 37 degrees C) Whole degree F, 0.5 degree C (0.1 degree F in test mode) 2 degrees F (1 degree C) between heating and cooling Toggle Button located on front display 41 to 149 degrees F (5 to 65 degrees C), 0-95% RH noncondensing 33 to 149 degrees F (1 to 65 degrees C) 3.5” W x 3.5” H x 0.9” D (89 mm x 89 mm x 23 mm) FCC, CE Mark Figure 4 E527 Dimensions E527 Datasheet Page 6 of 7 Ordering Information The e527 is available in several operating configurations, all based on the same fundamental hardware platform. The ordering part numbers (OPN) are formed by a combination of the elements, as shown below. Assembly e527 Logic L0 L1 Description Final Assembly 201-527 Description No Radio Logic Board Radio Logic Board 202-151.L0 202-151.L1 Communications R0 R1 User Interface Humidity Sensor Description No Humidity Sensor Humidity Sensor Description No Logo Part Number 203-203.R0 203-203.R1 Description 6 button with PIR and EcoMode 6 button with PIR, without EcoMode 6 button EcoMode only 6 button no PIR, no EcoMode 5 button with PIR and EcoMode 5 button with PIR, without EcoMode 5 button EcoMode only 5 button no PIR, no EcoMode Logo OPN Part Number Description No RS485 RS485 6PE 6P0 60E 600 5PE 5P0 50E 500 Part Number Part Number 02-9972 02-9972 02-9972 02-9972 Part Number 02-9463 E527 Datasheet Logo OPN Page 7 of 7 Description INNCOM Logo Johnson Controls Logo Housing Color OPN WH BK LA EA Description White Black Light Almond Eagle Almond For American gang installation, add mounting plate 53-6092. Use wiring harness 62-1462 for the RS485 connection and 62-1465 for S5 and external temperature sensor. Document Revision History Revision 0.1 0.2 0.3 0.4 1.0 1.1 Date Issued 01-Jun-2012 05-Jun-2012 20-Jun-2012 09-Jul-2012 09-Jul-2012 07-Sep-2012 Reason First Draft Incorporated comments from AE review Incorporated R&D review comments Incorporated RS485 Deep Mesh information Finalized for release Added FCC language change
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2012:10:01 08:39:48Z Modify Date : 2012:10:01 09:26:38-04:00 Page Count : 7 Producer : GPL Ghostscript 8.15 Creation Date : 2012:10:01 08:39:48Z Mod Date : 2012:10:01 09:26:38-04:00 Author : mahussain Metadata Date : 2012:10:01 09:26:38-04:00 Title : Microsoft Word - E527 Datasheet v1.2 DS.doc Creator : mahussainEXIF Metadata provided by EXIF.tools