Honeywell 51306799 LOW COST ISA 100 RADIO MODULE(51306799-001) User Manual KEYBEE

Honeywell International Inc. LOW COST ISA 100 RADIO MODULE(51306799-001) KEYBEE

User Manual

Download: Honeywell 51306799 LOW COST ISA 100 RADIO MODULE(51306799-001) User Manual KEYBEE
Mirror Download [FCC.gov]Honeywell 51306799 LOW COST ISA 100 RADIO MODULE(51306799-001) User Manual KEYBEE
Document ID1489407
Application ID3Zdcw1NIThe22z/BVQ6hyQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize19.63kB (245325 bits)
Date Submitted2011-06-24 00:00:00
Date Available2011-06-28 00:00:00
Creation Date2011-06-14 15:24:23
Producing SoftwareAcrobat Distiller 9.4.2 (Windows)
Document Lastmod2011-06-14 15:24:28
Document TitleKEYBEE
Document CreatorAcrobat PDFMaker 9.1 for Word
Document Author: Rajesh

________________________________________________________________________
Low cost RF Module (LCRM) ‐ User Manual
Product Manual
For RF Module part numbers,
Radio Assembly : 51306799‐125
Printed wiring board no : 51306799‐001
2.4GHz, 802.15.4 Module.
Copyright 2011 by Honeywell International Inc.
Revision 2, May 30th, 2011
______________________________________________________________________________________
LCRM User Manual
Page 1 of 10
Revision No 2.0 30/05/2011
________________________________________________________________________
Document Revision History
Date
22.2.2011
30.5.2011
Author
Abhijit
Biswas
Description/Changes
Initial
Modified after Review with TUV
Revision
1.0
2.0
______________________________________________________________________________________
LCRM User Manual
Page 2 of 10
Revision No 2.0 30/05/2011
________________________________________________________________________
Contents
1.COMPLIANCE STATEMENTS ....................................................................................................................... 4
2.DESCRIPTION ............................................................................................................................................ 6
3. FEATURES ................................................................................................................................................ 6
4. ELECTRICAL CHARACTERISTICS.................................................................................................................. 6
5. PIN OUT DIAGRAM................................................................................................................................... 6
6. CONFIGURATION SOFTWARE.................................................................................................................... 7
7. APPROVED ANTENNA TYPES/ GAIN .......................................................................................................... 7
8 SETTING TX POWER……………………………………………………………………………………………………………………………………8
9 INSTRUCTIONS TO OEM INSTALLER……………………………………………………………………………………………………………9
10 LIMITED MODULAR APPROVAL ……………………………………………………………………………………………………………10
11 AGENCY LABEL INFORMATION………………………………………………………………………………………………………………10
______________________________________________________________________________________
LCRM User Manual
Page 3 of 10
Revision No 2.0 30/05/2011
________________________________________________________________________
1. Compliance Statements:
1.1 FCC Compliance Statements
This device complies with Part 15 of the FCC rules. Operation is subject to following
two conditions: 1. This device may not cause harmful interference and 2. This device
must accept any interference received including interference that may cause undesired
operation of this device.
The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
To comply with the FCC RF exposure compliance requirements, this device and its antenna
must not be co-located or operating to conjunction with any other antenna or transmitter,
except if installed in compliance with FCC Multi Transmitter procedures.
To inherit the modular approval, the antennas for this transmitter must be installed to provide
a separation distance of 20cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter
To OEM Installer:
1. FCC ID on the final system must be labeled with “Contains FCC ID: S5751306799”
Or “Contains transmitter module FCC ID: S5751306799”.
2. In the user manual, final system integrator must ensure that there is no instruction
provided in the user manual to install or remove the transmitter module.
3. Transmitter module must be installed used in strict accordance with the
manufacturer’s instructions as described in the user documentation that
comes with the product.
The user manual of the final host system must contain the following statements:
This device complies with Part 15 of the FCC rules. Operation is subject to following
two conditions: 1. This device may not cause harmful interference and 2. This device
must accept any interference received including interference that may cause undesired
operation of this device.
The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
To comply with the FCC RF exposure compliance requirements, this device and its antenna
must not be co-located or operating to conjunction with any other antenna or transmitter,
except if installed in compliance with FCC Multi Transmitter procedures.
To inherit the modular approval, the antennas for this transmitter must be installed to provide
a separation distance of at least 20cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter
Note:
The buyer of the module who will incorporate this module into his host must submit the final
product to the manufacturer of the module and the MANUFACTURER OF THE MODULE
WILL VERIFY that the product is incorporated in host equipment in a way that is represented
by the testing as shown in the test report.
______________________________________________________________________________________
LCRM User Manual
Page 4 of 10
Revision No 2.0 30/05/2011
________________________________________________________________________
1.2 IC Compliance Statements
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause undesired
operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna
of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna type and its gain should be
so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres
utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une
communication satisfaisante.
This radio transmitter has been approved by Industry Canada to operate with the antenna
types listed below with the maximum permissible gain and required antenna impedance for
each antenna type indicated. Antenna types not included in this list, having a gain greater
than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les
types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance
requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont
le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur.
To inherit the modular approval, the antennas for this transmitter must be installed to provide
a separation distance of at least 20cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter
Note:
The buyer of the module who will incorporate this module into his host must submit the final
product to the manufacturer of the module and the MANUFACTURER OF THE MODULE
WILL VERIFY that the product is incorporated in host equipment in a way that is represented
by the testing as shown in the test report.
______________________________________________________________________________________
LCRM User Manual
Page 5 of 10
Revision No 2.0 30/05/2011
________________________________________________________________________
2. Description:
Low Cost ISA100 Radio Module is 2.4GHz band 802.15.4 Radio. This module includes 16 Bit
Microcontroller which is interfaced to a 802.15.4 compliant Radio Transceiver to provide Wireless
communication over 15Channels of 2.4GHz band. The module also includes RF Power Amplifier
and RF Low Noise Amplifier to enhance the range of Wireless Communications. The Module can
communicate with the target boards through its connector over SPI. It can send out or receive,
data - sent by or sent to, the target board through this SPI connection. Protocol specific
Modulation/De-Modulation is done in radio transceiver and the 802.15.4 packet is taken care by
Radio Transceiver on the Module.
3. Features:






Operating frequency
No. of channel
Channel spacing
Transmitted power
Modulation
Data rate
2.4 to 2.483GHz
15
5MHz (2405,2410,…..2475)
-7 to +20dBm (adjusted as per antenna)
DSSS
250kbps
4. Electrical Characteristics
 Operating Voltage : 2.7V to 3.6V
 Operating Temperature : -40 deg C to +85 deg C.
 Current Consumption :
Receive Mode (Rx) : 32mA
Transmit Mode (Tx) : 220mA
Sleep Mode : 13uA
5. Pin out Diagram
Table 5‐1 : I/O Interface of the LCRM RF Module
GND
I/O
SPI_CLK
SPI_MOSI
VCC
GND
I/O
SPI_MISO
SPI_CS
10
VCC
______________________________________________________________________________________
LCRM User Manual
Page 6 of 10
Revision No 2.0 30/05/2011
________________________________________________________________________
6. Configuration Software
The radio platform can host multiple standard protocol stacks like ISA100, zigbee, 802.15.4 pt to pt
and any proprietary protocol stack which could use the same hardware platform running on 802.15.4
physical layer. The configuration parameters for power level, frequencies are adjusted as per the
antenna table used during compliance tests. For compliance tests, test software running hyper
terminal is used to configure the power levels, frequencies etc.. as per the table given below. The
commands shall be available through host application to communicate to the radio module for
configuration of Tx power levels.
The power levels are configured in the registers of radio transceiver used on the module and adjusted
as per the antenna table. The frequencies i.e 15 channels are pre-defined as per 802.15.4
arrangement in 2.4GHz band excluding the last channel i.e 16th channel, 2480MHz.
7. Approved Antenna Types/ Gains
Table 7-1 : Antenna vs Transmit power table
Antenna 2, 3, 4, 5 & 7 are with Reverse SMA connector.
Antenna 1, 8, 9 & 10 are with N type connector.
Antenna 6 is with MMCX type connector.
______________________________________________________________________________________
LCRM User Manual
Page 7 of 10
Revision No 2.0 30/05/2011
________________________________________________________________________
8. Setting Tx Power
Warning! The Low Cost ISA100 Radio Module must be Professionally Installed in
accordance with the requirements specified in this document. Only the specified power
Settings, antenna types and gains as outlined in this document are valid for Low Cost ISA100
Radio Module installation.
The Tx power settings for the radio module are to be configured using a host interface with
the module. The module has an SPI communication interface which can communicate to any
host carrier. The power settings are provided as configurable parameter through host
interface. The configurable parameter will be in terms of RF output power in dBm available at
the connector output of the radio board as given in the figures below,
Figure 8-1 : Transmit power configuration – Field installation
Alternatively power levels can be preconfigured in LCRM RF module in factory as per the
antenna combination being shipped out with the product.
LCRM module can host different types of communication stack software like ISA100, Zigbee,
15.4 pt to pt etc..which can typically use 15.4 physical layer for the wireless communication.
Irrespective of the communication stack being ported on the LCRM module, the basic
configurations of channels and power levels as per the antenna shall remain same as given in
the user manual. As explained above, this can be either done through a professional
installation at the field or through a preconfigured power level with a particular antenna
combination shipped out from factory.
Professional installation has to be done by a person who has sufficient knowledge about
settings of radio parameters of the module. It will void OEM installers authority to operate and
sell the equipment if this is done incorrectly.
The power table is as given below,
______________________________________________________________________________________
LCRM User Manual
Page 8 of 10
Revision No 2.0 30/05/2011
________________________________________________________________________
Table 8-1: Transmit power configuration of LCRM Module
S.No
10
11
12
13
14
15
16
Power level
20dBm
19dBm
18dBm
17dBm
15dBm
14dBm
12dBm
11dBm
10dBm
6dBm
4dBm
3dBm
1dBm
0dBm
‐1dBm
‐5dBm
9. Instruction to OEM installer
OEM installer shall refer user manual for configuration of transmit power as per the antenna
table given in table 7-1.
The listed antennas in table 7-1 include N type connector, Reverse SMA connector and
MMCX connector. Installer shall use only the antennas which are listed in the table to comply
with FCC regulations.
Integrators of this module in their end product are instructed to glue the N type antenna
connector to the socket of the final product.
For the final product OEM installer must ensure that the power setting of the module are not
end user accessible.
When integrated into OEM products, fixed antennas require installation preventing end-users
from replacing them with non-approved antennas. Antennas not listed in the tables must be
tested to comply with FCC Section 15.203 (unique antenna connectors) and Section 15.247
(emissions).
For non-approved antennas, each installation of the module in the host must be approved by
a class II permissive change by the TCB/FCC through Honeywell.
______________________________________________________________________________________
LCRM User Manual
Page 9 of 10
Revision No 2.0 30/05/2011
________________________________________________________________________
10. Limited modular approval
This is an RF module approved for limited modular use limited to OEM installation for mobile
and fixed applications only. Final antenna installation in the product and operating
configurations of the transmitter including antenna gain and cable loss shall comply with FCC
regulations. Honeywell must coordinate with OEM integrators to ensure the end-users and
installers of products operating with the module are provided with operating instructions to
satisfy RF exposure requirements. Integrators are instructed to ensure the end-user has no
manual instructions to remove, adjust or install the device.
11.
Agency Label Information
FCC/IC Labels
RF MOD 51306799-001
FCC ID: S5751306799
IC ID: 573I-51306799
______________________________________________________________________________________
LCRM User Manual
Page 10 of 10
Revision No 2.0 30/05/2011

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Rajesh
Comments                        : 
Company                         : Reindeer Systems Pvt Ltd
Create Date                     : 2011:06:14 15:24:23+05:30
Modify Date                     : 2011:06:14 15:24:28+05:30
Source Modified                 : D:20110614095359
Subject                         : 
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : Acrobat PDFMaker 9.1 for Word
Metadata Date                   : 2011:06:14 15:24:28+05:30
Producer                        : Acrobat Distiller 9.4.2 (Windows)
Keywords                        : 
Format                          : application/pdf
Creator                         : Rajesh
Title                           : KEYBEE
Description                     : 
Document ID                     : uuid:36e917f0-05c0-4403-8133-1a54335142f3
Instance ID                     : uuid:77182507-093d-44e4-a1c3-9e13635b7743
Page Layout                     : OneColumn
Page Count                      : 10
EXIF Metadata provided by EXIF.tools
FCC ID Filing: S5751306799

Navigation menu