Honeywell 7800LG Dolphin® 7800 Mobile Computer User Manual 2 of 2

Download:
Mirror Download [FCC.gov]
Document ID	1588433
Application ID	dw+Rj0cGwqOEciYpraCbqg==
Document Description	user manual 2 of 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	219.22kB (2740310 bits)
Date Submitted	2011-11-25 00:00:00
Date Available	2012-05-23 00:00:00
Creation Date	2017-11-03 04:12:27
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-11-03 04:12:27
Document Title	Microsoft Word - DRAFT_COPY_7800-Users-Guide_11-11-11_Gobi.rtf
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Irene

DRAFT COPY 11/11/11
RIL
The RIL Information screen displays useful statistics for the GSM WAN Voice module (PH8). To verify
whether or not the GSM radio is enabled, check the Dolphin Wireless Manager (see page 8-4).
Power
Power system settings contains two tabs: Battery and Advanced
Tap
> Settings > System > Power
Battery Tab
The battery tab displays the power level status of the
main battery and the status of the backup battery.
Note: The Backup Battery gauge registers either 0% or 100%.
The percentage is not an indication of the level of charge
remaining on the backup battery. An installed and
functional battery registers 100%. A total discharge or a
battery error registers 0%.
For detailed information on the main battery pack, see
Battery on page 7-10.
Advanced Tab
Determines power time-outs.
For On battery power, select from the drop-down list, the
number of minutes of inactivity you want to pass before the
terminal powers off when running on battery power.
For On external power, select from the drop-down list, the
number of minutes of inactivity you want to pass before the
terminal powers off when running on external power.
Note: When the terminal “powers off”, it enters Suspend Mode, see page 2-11 for additional information.
Regional Settings
Regional Settings enables you to customize the appearance and formatting to your geographic region.
Specifically, you can customize numbers (i.e., number of decimal places allowed), currency (i.e.,using
the $ or € symbol), time, and date. These specifications apply to all screens, including the Home screen.
The Region tab displays an overview of the region selected in the drop-down list at the top.
7 - 15
DRAFT COPY 11/11/11
The terminal is loaded with a number of pre-programmed regional settings. Select one from the list and
the results appear on the screen. To see specific settings or to change a specific setting, tap on one of
the items on the horizontal scroll bar (i.e., Region, Number, Date), make the change, and tap OK to
save.
Remove Programs
Remove Programs enables you to remove programs installed on the terminal. Any program (usually CAB
or DLL files) stored in the \\IPSM\Honeywell\Autoinstall folder re-installs after a software upgrade or a
factory reset. If a program is manually removed using the Remove Programs application, the program
does not re-install on a hard or soft reset.
Note: A program (file) does not automatically install if it is added to the \\IPSM\Honeywell\Autoinstall folder and a
hard or soft reset is performed. For information on program installation, see Installing Additional Software on
page 8-8.
For information about the system resets, see Resetting the Terminal on page 2-11. See Honeywell support for more information on how to perform a factory reset.
1. Tap Remove Programs. In the list, select the program you want to remove.
2. Tap Remove. The following message appears:
3. Tap Yes. Wait while the program is removed.
4. Verify that the program no longer appears in the list.
7 - 16
DRAFT COPY 11/11/11
Screen
The Screen system setting contains three screens: General, Clear Type, and Text Size.
General Screen
Orientation
The General screen enables you to set the dynamic screen
rotation. Three choices of screen orientation are supported:
Portrait, Landscape (right-handed), and Landscape (lefthanded).
Align Screen
The General Tab also allows you to re-align the screen.
You need to re-align the screen if tapping buttons or icons with
the stylus no longer seems to work appropriately.
Tapping Align Screen brings up the align screen window
where you are guided to tap a target several times. This recalibrates how the touch screen receives input.
• Alignment should always be performed with a stylus
designed for touch panel applications. The small point is
required for accurate calibration.
• Press the stylus firmly into the center of the cross-hair target
once and release. Do not “double-tap” the target.
ClearType Screen
The display supports ClearType font rendering, which is a
Microsoft technology that dramatically increases the readability
of text on LCD displays.
To enable ClearType font rendering, select Enable ClearType
and tap OK.
For more information about ClearType font rendering, visit:
www.microsoft.com/typography/WhatIsClearType.mspx.
7 - 17
DRAFT COPY 11/11/11
Text Size Screen
The Text Size screen enables you to perform font scaling within
certain views of the:
• Home screen,
• Contacts,
• Calendar,
• Messaging, and
• Tasks.
Font scaling means that you can increase or decrease the
point size of the font on application windows.
To change the font size, move the slider toward Smallest or
Largest. The Example text changes to reflect the font change.
Tap OK to save the new font size setting.
Task Manager
The Task Manager provides information about applications and processes running on your mobile computer. You can use the Task Manager to monitor the memory and CPU usage of specific applications and
processes. Check the Task Manager when you are receiving out of memory errors or when the mobile
computer is running slowly.
7 - 18
DRAFT COPY 11/11/11
Using the Task Manager
Applications
To view the status of the programs running on your
mobile computer, tap the Menu button at the bottom of
the screen, then tap View > Applications.
From the application list, you can:
• Tap and hold on an application, then tap Switch To on
the pop-up menu.
• Tap and hold on an application, then tap End Task or
End All Tasks on the pop-up menu.
Note: Anytime you stop a running program, it frees up memory. To free up memory, return to the running
program, save your data, and close the application.
Processes
To view information about the processes running on the
mobile computer, tap the Menu button at the bottom of
the screen, then tap View > Processes.
7 - 19
DRAFT COPY 11/11/11
7 - 20
8
DRAFT COPY 11/11/11
Communication
Connections Menu
The Connections system setting provides access to the terminal’s various wireless communication
options.
Icon
Tapping this icon…
Beam
Enable the terminal to receive incoming beams from devices using Bluetooth
wireless technology. See Working with the Bluetooth Radio on page 10-1.
Connections
Opens Microsoft’s connections manager. See Connections Manager on page 8-2.
Dolphin
Wireless
Manager
Manages the wireless radios installed in the terminal. See Dolphin
Wireless Manager on page 8-4.
Domain
Enroll
Opens the Enrollment screen for connecting your phone with company resources.
USB to PC
Enables advanced wired USB to PC communication via sync sofware. See
Connecting and Synchronizing the Terminal and Workstation on page 8-6.
Network
Cards
Manage Network card settings.
Note: The Dolphin Wireless Manager icon may not appear on the Connections
menu on terminals running Microsoft Windows Embedded Handheld 6.5
Classic. For information on how to access the Dolphin Wireless Manager,
see page 8-4.
Note: System administrator password is required for domain enrollment.
Note: All server-assigned IP addresses use Dynamic Host Configuration Protocol (DHCP).
8-1
DRAFT COPY 11/11/11
Connections Manager
Microsoft’s Connections Manager sets up multiple network connections to Internet Service Providers
(ISPs) via external modem.
Do NOT enter connection parameters in the Connections Manager if:
• you are using one of the on-board wireless radios to connect to a network. The Dolphin terminal uses
the settings from each radio’s configuration utility to connect. The connections manager is used
primarily to setup WAN modem dial up connections.
• you are using Wireless Zero Config. By default, WZC is disabled on Dolphin terminals.
To Access the Connections Manager
Tap
> Settings > Connections
> Connections
Tasks
The Tasks screen enables you to initially configure, and then manage network settings when using a
modem. Select an item in this list and then complete the setup screens that follow with the appropriate
information for your network.
My ISP
The links under this heading enables you to add and manage modem connections to an ISP. To complete the setup screens, obtain the following information from your ISP:
•
•
•
•
ISP dial-up access telephone number
Username
Password
TCP/IP settings
My Work Network
These links enable you to establish the following connections types:
• Modem
• Virtual Private Network (VPN)
8-2
DRAFT COPY 11/11/11
• Proxy server connection
Note: If you are connected to your ISP or private network during synchronization, the terminal should
download the proper proxy settings during synchronization with the workstation. If these settings are not
on your workstation or need to be changed, ask your ISP or network administrator for the proxy sever
name, server type, port, type of Socks protocol used, and your user name and password.
To complete the setup screens, obtain the network parameters from your system administrator.
Modify an Existing Connection
Manage Existing Connections appears on the Connections tab after at least one network connection
has been established.
Tap Manage Existing Connections on the Horizontal scroll and follow the setup screens.
Advanced
The Advanced screen enables you to select the default network, dialing rules, and IP address exceptions
for modem connections.
Note: You should not need to change Advanced settings because most ISPs now use DHCP addresses.
8-3
DRAFT COPY 11/11/11
Dolphin Wireless Manager
The Dolphin Wireless Manager provides a centralized interface that enables and disables all the onboard radios. Each radio has its own configuration program. The Dolphin Wireless Manager also provides shortcuts to the configuration utilities for each radio.
Tap
on the Home screen to access the Dolphin Wireless Manager.
OR
1. Tap once on the Title bar to access the Horzontal Scroll bar.
2. Tap
3. Select, “Dolphin Wireless Manager”.
Dolphin Wireless Manager Window
These buttons show you the
state of the radio.
If applicable, information about
the radio appears when the
radio is activated.
Enabling the Radios
1. Tap
on the Home screen to access the Dolphin Wireless Manager.
2. Tap anywhere inside the rectangle of the radio you want to enable.
3. The radio begins activating.
8-4
DRAFT COPY 11/11/11
4. When the radio is activated (i.e., transmitting a signal), the OFF button changes to ON.
Note: If applicable, information about the radio appears in the rectangle.
Accessing Radio Configuration Utilities
Each radio has its own configuration utility that you can access by tapping Menu on the tile bar.
Radio Type
Menu Option
802.11a/b/g/n
Tap WLAN Settings and the Honeywell WLAN Security Supplicant opens.
The Honeywell WLAN Security Supplicant User’s Guide is available for
download from the Dolphin 7800 product page at www.honeywellaidc.com.
Bluetooth
Tap Bluetooth Settings and the Bluetooth Settings screen opens.
For details, see Working with the Bluetooth Radio on page 10-1.
GSM/HSDPA/UMTS/GPRS/ Tap Phone Settings and the Phone opens.
EDGE
For details, see Working with Wireless Wide Area Networking (WWAN) on
page 9-1.
GSM/CDMA
Tap Gobi Settings and the Gobi Manager opens.
For details, see Gobi Manager on page 9-11.
8-5
DRAFT COPY 11/11/11
Network Cards
The Network Cards screen allows you to set and configure the type of Network Adapter the Network
card in the terminal uses. You can modify the adapter settings (e.g., Name Servers or IP address) by
tapping on the adapter type or highlighting the adatpter and tapping Edit at the bottom of the screen.
Connecting and Synchronizing the Terminal and Workstation
To synchronize data between the terminal and the workstation, ActiveSync (version 4.5 or higher) or
Windows Mobile Device Center (WMDC) must be installed and configured for the appropriate communication type on the host workstation (Windows-based PC) and the Dolphin terminal. Dolphin terminals
ship with ActiveSync already installed. Therefore, if ActiveSync or WMDC is already installed on the host
workstation, you just need to connect the Dolphin terminal to the host workstation (via Dolphin peripheral) to initiate communication.
If ActiveSync (4.5 or higher) or WMDC is not installed on the host workstation, you can download and
http://go.microsoft.com/fwlink/?LinkId=147001 the most current version of the software from the
Microsoft Web site (http://go.microsoft.com/fwlink/?LinkId=147001).
Note: ActiveSync on your Dolphin terminal works with WMDC on host workstations running Windows Vista or
Windows 7 and with ActiveSync on host workstations running Windows XP. For detailed information on
ActiveSync and WMDC visit the Microsoft Windows Phone Web site.
When communicating via ActiveSync or WMDC, your terminal is designed to be connected to the host
workstation with a communication peripheral sold/manufactured by Honeywell, such as the charge/
communication cable. Use of any peripheral not sold/manufactured by Honeywell may cause damage not
covered by the warranty.
Capabilities
• Back up and restore your device data.
• Copy (rather than synchronize) files between your device and workstation.
• Control when synchronization occurs by selecting a synchronization mode. For example, you can
synchronize continually while connected to your workstation or only when you choose the synchronize
command.
8-6
DRAFT COPY 11/11/11
• Select which information types are synchronized, controling how much data is synchronized. For
example, you can choose how many weeks of past appointments you want synchronized.
Communication Types
The 7800 terminal supports Hi-Speed USB communication (USB 2.0) via ActiveSync through the I/O
Connector (see page 3-10) on the bottom panel of the terminal. The maximum data transfer rate is 480
Mbps. A USB cable and a Honeywell hardware peripheral (e.g., HomeBase) allow the terminal to communicate with a workstation or to networked through a USB hub. The Dolphin terminal defaults to USB
communication out of the box.
Hardware Requirements for Setup
• Dolphin communication peripheral (e.g., HomeBase, eBase, USB Communication/Charge Cable) and
power supply.
• A USB cable if one is not supplied with your Dolphin communication peripheral.
Software Requirements for Communication
• ActiveSync (v4.5 or higher) or Windows Mobile Device Center installed and configured on the host
workstation (PC), see Setting Up the Host Workstation on page 8-7.
Note:
ActiveSync or Windows Mobile Device Center must be setup on your workstation before you initiate
synchronization from the terminal for the first time.
• Windows 98 Second Edition, Windows Me, Windows 2000, Windows NT (4.0 SP6 or higher), Windows
XP, Windows Vista, and Windows 7 operating systems.
Setting Up the Host Workstation
To synchronize data between the terminal and the workstation, ActiveSync (v4.5 or higher) or Windows
Mobile Device Center must be configured for same communication type on both the host workstation
and the Dolphin terminal.
ActiveSync
Verify that ActiveSync is configured to use the appropriate communication type.
1. In the ActiveSync window on your workstation, select File > Connection Settings.
2. Check the box next to “Allow USB connections”.
Connecting the Dolphin Terminal to the Host Workstation
After setting up both the workstation and the terminal:
1. Connect the Dolphin terminal to the workstation using a Dolphin communication peripheral.
2. ActiveSync or Windows Mobile Device Center should open and connect automatically to the Dolphin
terminal.
8-7
DRAFT COPY 11/11/11
Synchronizing with the Host Workstation
After setup, synchronization begins automatically whenever the terminal’s mechanical connector connects to a Dolphin peripheral that is connected to a host workstation with ActiveSync or Windows Mobile
Device Center installed. For additional information visit the Microsoft Phone Web site (http://go.microsoft.com/fwlink/?LinkId=147001).
Exploring the Terminal from the Workstation
ActiveSync
1. Open the main ActiveSync window (on the desktop).
2. Click Explore. This opens the Mobile Device folder for the terminal in Windows Explorer.
3. The Dolphin terminal is now treated as a mass storage device, and transferring files is as simple as
dragging and dropping or copying and pasting.
Windows Mobile Device Center
1. Open Windows Mobile Device Center (on the desktop).
2. Click File Management. This opens the Mobile Device folder for the terminal.
3. The Dolphin terminal is now treated as a mass storage device, and transferring files is as simple as
dragging and dropping or copying and pasting.
Installing Additional Software
Dolphin terminals ship with the operating system, radio drivers, and custom Honeywell software already
installed. These are the default programs that install when your terminal first boots up. You can install
additional software programs to the terminal provided that the following parameters are met:
• The software program was created for a Windows Embedded Handheld 6.5 device.
• The terminal has enough memory to store and run the program.
• The program has an EXE, CAB, or DLL extension.
When selecting programs, verify that the program and version of the program are designed for the Windows Embedded Handheld 6.5 and the terminal’s processor. You can verify your processor by tapping
> Settings > System > About > Version. Make a note of the information in the Processor field.
To install additional software, you can use the communication options described in this chapter.
• Adding Programs Using ActiveSync or Windows Mobile Device Center, see page 8-8.
• Adding Programs Using the Internet, see page 8-10.
Adding Programs Using ActiveSync or Windows Mobile Device Center
Generally, software for Windows Embedded Handheld devices must be installed to the host workstation
first, then transferred to the Dolphin terminal.
Note: An active Microsoft ActiveSync or Windows Mobile Device Center connection between a host workstation and
the Dolphin terminal is required to add programs. For additional information, see Connecting and
Synchronizing the Terminal and Workstation on page 8-6.
8-8
DRAFT COPY 11/11/11
1. Download the program to the workstation from either the Internet or the install CD. You may see a
single *.exe or setup.exe file, a *.cab file, or a *.dll file.
Note: There may be several versions of files for different device types and processors. Select the file that
matches the terminal’s processor.
2. Read any installation instructions, Read Me files, or documentation that comes with the program.
Many programs provide special installation instructions.
3. Connect the terminal to the workstation via a Dolphin communication peripheral.
If the File is an Installer (*.exe or *.setup.exe)
An installer program is one that installs on the workstation and the terminal simultaneously; one process
installs to both devices.
1. On the workstation, double-click the *.exe or setup.exe file. The installation wizard begins.
2. Follow the directions on the workstation screen. The installation process includes transferring the
software to the Dolphin terminal.
If the File is Not an Installer
Some programs cannot be installed on PCs because they are designed exclusively for Windows Embedded Handheld devices. In these cases, the appropriate files must be stored on the host workstationand
transferred to the terminal via ActiveSync Explore or Windows Device Mobile File Management.
Note: You know that the program is not an installer because an error message stating that the program is valid but
designed for a different type of computer appears when you try to install the program on the workstation.
1. If you cannot find any installation instructions for the program in the Read Me file or documentation,
do one of the following:
a. Open ActiveSync and click Explore, or
b. Open Windows Mobile Device Center and click File Management
2. On the workstation, navigate to the workstation folder containing the program file(s). Copy and
paste the file(s) into the Program Files folder on the terminal.
• If you want the program to be part of the Autoinstall that occurs after a factory reset or software
upgrade, paste the program file(s) in both the \IPSM\Honeywell\Autoinstall folder and
the \Honeywell\Autoinstall.
Note: Contact a Honeywell technical support representative for information on how to perform a factory reset.
See Technical Assistance on page 18-2 or go to www.honeywellaidc.com.
3. On the terminal from the Start screen, tap File Explorer, navigate to the folder where the program is
located.
4. Tap on the program file to start the installation.
• If you copied the file to the \Honeywell\Autoinstall folder, you can perform a Soft Reset
(CTRL + ENTER) to install the program. For more information, see Hardware Maintenance on
page 3-16.
8-9
DRAFT COPY 11/11/11
Connecting the Terminal to a Wireless Network
You connect the terminal to a wireless network through the on-board radio (802.11a/b/g/n, Bluetooth,
and/or GSM/CDMA). Each radio has its own configuration utility and requires specific information about
the wireless network to connect. Successful connection depends on your network infrastructure about
which you will need specific information from your network administrator.
WLAN (802.11a/b/g/n)
The 7800 has a 2.4 GHz 802.11b/g/n - 5.0 GHz 802.11a/n WLAN (Wireless Local Area Network) radio.
The radio is interoperable with other 802.11a/b/g/n, Wi-Fi compliant products including access points
(APs), workstations via PC card adapters, and other wireless portable devices. By default, the 802.11a/
b/g/n radio is disabled after each factory reset. The next step is to configure the connection parameters
of the radio to connect to a wireless network.
WLAN Radio
The WLAN radio is configured in the Honeywell WLAN Security Supplicant, which you access by tapping
the program icon in the task tray near the bottom of the touch screen. For complete configuration instructions, download the Honeywell Secure Wireless (SWC) Client User’s Guide from
www.honeywellaidc.com. A link to this guide appears on the Dolphin 7800 product page.
Adding Programs Using the Internet
When you have established a network connection, you can access the Internet and download additional
software programs.
Note: When selecting programs, verify that the program and version of the program are designed for Windows
Embedded Handheld and the terminal’s processor. You can verify your processor by tapping
> Settings > System > About > Version. Make a note of the information in the Processor field.
1. Open Internet Explorer and navigate to the program’s location. You may see a single *.exe or
setup.exe file, or several versions of files for different device types and processors.
2. Select the program version that matches your Dolphin terminal and processor.
3. Read any installation instructions, Read Me files, or documentation that comes with the program.
Many programs provide special installation instructions.
4. Download the program to the terminal directly from the Internet. You would normally store the
program in the \Program Files folder unless another location is required by the program.
5. On the terminal, tap the installer file: e.g., *.exe or setup.exe file.
6. The installation wizard for the program begins.
7. Follow the directions on the screen to complete the installation.
Software Upgrades
Contact a Honeywell technical support representative for information on available software upgrades for
your Dolphin terminal, see Customer Support on page 18-1 or go to www.honeywellaidc.com.
8 - 10
DRAFT COPY 11/11/11
To prevent data loss, back up all user data to an SD card or external memory device before
performing an upgrade.
Note: An active Microsoft ActiveSync or Windows Mobile Device Center connection between a host workstation and
the Dolphin terminal may be required for some types of software upgrades. For additional information, see
Connecting and Synchronizing the Terminal and Workstation on page 8-6.
For information on File Provisioning on the 7800, see page 2-10.
7800 COM Port Assignment Table
COM Port
Description
COM0
Unused
COM1
Unused
COM2
Bluetooth
COM3
Unused
COM4
Available
COM5
Bluetooth DUN
COM6
Unused
COM7
GPS: COM Port for the GPS receiver
COM8
USB Serial: Virtual USB Serial port for ActiveSync
COM9
Bluetooth BTHATCI server
8 - 11
DRAFT COPY 11/11/11
8 - 12
9
DRAFT COPY 11/11/11
Working with Wireless Wide AreaNetworking (WWAN)
Overview
The 7800 has two options for WWAN connectivity, a data+voice GSM/HSPA+/UMTS/GPRS/EDGE and
CDMA/EVDO radio or a data only Gobi radio, which supports GSM/HSPA+/UMTS/GPRS/EDGE and
CDMA/1xRTT/EVDO.
GSM
Short for Global System for Mobile communications, GSM is an open, non-proprietary wireless
WAN system that is constantly evolving and growing.
HSPA+
Short for High-Speed Download Packet Access, HSPA+ is a non-voice value added service that
allows packet-switched data to be instantly sent and received across mobile telephone networks.
UMTS
Short for Universal Mobile Telecommunications System, UMTS is a non-voice value added service
that allows packet-switched data to be instantly sent and received across mobile telephone
networks.
GPRS
Short for General Packet Radio Service, GPRS is a non-voice value added service that allows
packet-switched data to be instantly sent and received across mobile telephone networks.
EDGE
E-GPRS is a non-voice value added service that allows packet-switched data to be instantly sent
and received across mobile telephone networks at a higher data rate than standard GPRS.
CDMA
Short for Code Division Multiple Access.
1xRTT
Short for Single-Carrier Radio Transmission Technology.
EVDO
Short for Evolution-Data Optimized.
Requirements
Using GSM/HSPA+/UMTS/GPRS/EDGE requires:
• a network subscription to a GSM/HSPA+/UMTS/GPRS/EDGE network (you need to know what service
providers are in your geographic area), and
• an installed SIM card that has been activated by the network service provider (see Installing a SIM Card
and/or Memory Card on page 3-16).
Using a CDMA requires:
• an active account with a CDMA carrier. The account is linked to the Mobile Equipement Identifier
(MEID) of the integrated WWAN radio.
Antenna Band
The WWAN radio features an internal antenna that is optimized for power output and receiver sensitivity.
This is an omni-directional antenna.
For the data only Gobi 3000 WWAN radio, there is a unified penta band antenna 800/850/900/1900/
2100MHz (HSPA/UMTS), quad band antenna 850/900/1800/1900MHz (GSM/GPRS/EDGE), and dual
band antenna 850/1900MHz (EVDO/CDMA) support.
For the voice + data WWAN radio, there is a unified penta band antenna 800/850/AWS/1900/2100MHz
(HSPA+/UMTS), quad band antenna 850/900/1800/1900MHz (GSM/GPRS/EDGE), and dual band
antenna 850/1900MHz (EVDO/CDMA) support.
9-1
DRAFT COPY 11/11/11
Signal Strength
The signal strength of the WWAN connection is indicated by the number of bars that appear in the signal
strength icon in the Title bar at the top of the window.
Icon
Indicates…
The signal strength of the radio connection.
The signal strength of the phone (voice) connection;
see GSM/HSPA+ Global Radio Dolphin Models on
page 9-3.
The signal strength of the data connection; see Data
Communication (GSM/HSPA+ Global Radio Dolphin
Models) on page 9-7.
Voice and Data Communication
Dolphin terminals with integrated GSM/HSPA+/UMTS/GPRS/EDGE radios are optimized for the following two-way voice and data communications:
Voice: GSM voice data (dial-up)
Data: Available speed depends on the wireless network carrier and their supported packet-data
technology in addition to network conditions.
GPRS Class 10: data transmission max. 85.6 kbps (DL), max. 42.8 kbps (UL)
HSPA+: data transmission max. 14.4 Mbps (DL), max. 5.76Mbps (UL)
UMTS: data transmission max. 384 kbps (DL), max 384 kbps (UL)
EDGE (E-GPRS) Class 10: data transmission max. 237 kbps (DL), max. 118 kbps (UL)
You can use the GSM radio for voice communication and data communication, but not at the same time.
If you want to communicate over the phone (voice), you cannot send data. If you want to send data, you
cannot use the phone.
9-2
DRAFT COPY 11/11/11
Enabling the WWAN Radio
By default, the WWAN radio is not enabled after a factory reset. Verify the status of the radio in the Dolphin Wireless Manager.
Tap
on the Home screen to access the Dolphin Wireless Manager.
If the WWAN radio is OFF, tap the rectangle to enable or turn ON the radio.
GSM/HSPA+ Global Radio Dolphin Models
Voice Communication
You can use the Dolphin terminal as a phone over the GSM radio.
Audio Modes
The front panel of the 7800 contains both a speaker and a microphone that you can use to send and
receive audio signals over the GSM network, see Front Panel: 7800 on page 3-5.
There are two audio modes:
• Handset Mode - The front speaker is used for receiving handset voice calls and the front panel
microphone provides audio input to the terminal.
• Hands-Free Mode - Hands-free mode is when you use the rear speaker as a speakerphone. To
switch to speakerphone, tap on the speaker button in the Dialer window, see Accessing the
Dialer Window on page 9-4.
9-3
DRAFT COPY 11/11/11
Volume Control
Blue
Use the Dolphin keyboard to adjust the volume.
To raise the volume, press the Blue modifier key + up arrow.
To lower the volume, press the Blue modifier key + down arrow.
Blue
Or
Press the up or down arrow on the Volume Control button on the left side of the
device to adjust the volume of the active speaker, see Volume Control Button on
page 3-7.
Accessing the Dialer Window
Note: The WWAN radio must be active for voice communication, see Enabling the WWAN Radio on page 9-3.
Tap
on the Home screen or tap
> Phone
to open the Phone dialer.
Displays the network carrier
from the SIM card.
Displays the most
recent calls.
Toggles the touch screen
keypad ON or OFF.
Menu
Dialing
Once the dialer window is open, you can dial out two ways:
• Tap the buttons on the dialer window.
• Use the physical keyboard (when the keyboard is in numeric mode).
9-4
DRAFT COPY 11/11/11
Sending Calls
After the number is dialed, tap Talk
Note: The
or press the Send key
icon indicates that the phone is in use.
Ending Calls
While the phone call is live, tap End
or End Key
Accessing Voice Mail
Tap
> Phone
> Speed Dial
> Voice Mail > Call.
Note: Update the voice mail retrieval number by turning the phone OFF and then ON via the Dolphin Wireless
Manager, see Enabling the WWAN Radio on page 9-3.
View Options
From the view menu, you can modify the display screen to show Calls and Contacts, All Calls or Speed
Dial numbers.
Tap Menu
> View.
Setup Options
The Options menu contains four setting widows: Sounds, Security, Services, and Network.
Tap Menu
> Options.
Sounds
The Sounds screen enables you to customize the:
• Ring type (e.g., Ring, Increasing ring, Ring once,
Vibrate, Vibrate and ring, Vibrate then ring or None)
• Ring tone
• Keypad tone (e.g., Long, Short, or Off)
9-5
DRAFT COPY 11/11/11
Security
The Security screen provides access to establish or
change your security PIN. Check the box next to,
“Require a PIN when the phone is used” to enable the
PIN security feature.
Services
For each service, the phone reads settings from the
network stored on the SIM card and then displays the
available options from the carrier on the screen. To
customize the settings, select it from the list and tap
“Get Settings”.
9-6
DRAFT COPY 11/11/11
Network
You can find, select, and set your preferred network
order from the Network screen.
Data Communication (GSM/HSPA+ Global Radio Dolphin Models)
You set up data communication via the Connections Manager. The carrier on the SIM card is the ISP.
System Requirements
• The GSM radio must be enabled; see Enabling the WWAN Radio on page 9-3.
• You must have an active SIM card with a DATA plan installed; see Installing a SIM Card and/or Memory
Card on page 3-16.
Information Requirements
You must have from the SIM card carrier:
• The APN (access point name).
• The username and password of the account.
Establishing Data Communication
1. Tap
> Settings > Connection > Connections
2. Under My ISP, tap Add a new modem connection.
9-7
DRAFT COPY 11/11/11
3. Enter a name for the connection. Select Cellular Line (GPRS) as the modem. Tap Next.
4. Enter the Access point name. Tap Next.
5. Enter the username and password from the account. Tap Finish.
9-8
DRAFT COPY 11/11/11
6. The connection you just created should appear in the list on the modem tab.
7. Tap and hold on the connection. Select Connect on the popup menu.
8. The network icon in the Title bar indicates the GSM radio is attempting to connect
Note: When the device is on a 2G (EDGE/GPRS) network, a data connection failure occurs if the phone is in
use for a voice call while attempting a data connection. Simultaneous voice and data use is only
supported if the device is on a 3G network. In 2G mode, a voice call takes precedence over data
connections. Active data connections are placed in "park" mode automatically and the data is "retrieved"
when the voice call ends.
9. When the connection is complete, the network icon changes to:
10. You can now send data over GSM.
Ending the Data Connection
By default, the data connection will disconnect after a certain amount of time passes without use.
This period of time is determined by ISP.
To end the data connection manually, tap the network icon
the popup bubble.
in the Title bar and select Disconnect on
9-9
DRAFT COPY 11/11/11
Manual Network Selection
You can select Automatic or Manual network selection. The Phone defaults to Automatic network selection.
1. When an active SIM card is inserted in the terminal, tap
> Settings > Personal > Phone
> Menu > Options.
2. Select the Network tab.
3. Under Network selection, select Automatic (the default selection) or Manual.
a. If you select Manual, the Phone searches for available networks.
b. The found networks appear.
c. Select a new network and tap OK. The Phone registers on the new network and the Network tab
appears.
d. To switch to another network, tap the now active Select button and the process repeats.
4. To switch back to automatic roaming, select Automatic under Select networks and tap OK.
9 - 10
DRAFT COPY 11/11/11
Data Communication GSM/CDMA Dolphin Models
Gobi Manager
The Gobi Manager enables you to see real time status of the radio, setup your Network selection, view
you’re profile and scan for networks. The Gobi Manager contains four tabs: Status, Setup, Profile, and
About.
1. Tap
on the Home screen to access the Dolphin Wireless Manager.
2. Tap Menu.
3. Select Gobi Settings.
Status Tab
The Status tab contains the real time radio status
information including:
• The power status of the radio (e.g., ON or OFF)
• The received signal strength intensity (RSSI)
• The radio mode used (e.g., GSM, UMTS, EVDO
or 1xRTT)
• The network firmware used
• The IP Address assigned
You can also turn the radio ON or OFF and Start or
Stop a data session from the Status tab.
Setup Tab
The Setup tab allows you to view and customize the
Network Setupincluding:
• The Nework Firmware (e.g., AT&T, Verizon,
Sprint, or T-Mobile)
• The SIM Slot accessed
• The Access Point Name (APN)
• The Username of the account
• The Password of the account
• Enable or Disable Automatic Data Sessions
• Activate Over the Air (OTA)
9 - 11
DRAFT COPY 11/11/11
The Profile tab allows you to see Radio capability
information and network statistics including:
Profile Tab
•
•
•
•
About Tab
Radio Hardware and Software versions
Radio and SIM identification numbers
Serving network connection type and state
Available radio interfaces for the current serving
network
Displays copyright and version information for the Gobi Connection Manager.
Establishing Data Communication
1. Tap
on the Home screen to access the Dolphin Wireless Manager.
2. Tap Menu and then select Gobi Settings.
3. From the Setup tab, select the carrier and enter user information (GSM only).
Note: An installed SIM card is required and the SIM slot option must be set to 0.
4. Check the Auto Start Data Session checkbox to automatically start the data session.
5. Tap the Apply button. The Connection Manager automatically switches to the Status Tab.
6. Tap the Radio Power ON button.
7. When the radio connects to the network, the status changes to “Registered” and a signal strength is
displayed.
8. If Auto Start Data Session was checked on the Setup tab, the state automatically changes from
“Registered” to “Data Session Open” and an IP address appears. If Auto Start Data Session was
not selected, then the Data session can be started manually by tapping Start Data Session button
from the Status tab.
9 - 12
10
DRAFT COPY 11/11/11
Working with the Bluetooth Radio
Enabling the Bluetooth Radio
You enable the Bluetooth radio in the Dolphin Wireless Manager (see page 8-4).
1. Tap
on the Home screen to access the Dolphin Wireless Manager.
2. Tap anywhere inside the Bluetooth rectangle and Bluetooth begins activating.
3. When the radio is activated (i.e., transmitting a signal), the OFF button changes to ON.
Now, the Bluetooth radio is transmitting a signal. Additional text in the Bluetooth section tells information
about the Bluetooth radio. “Visible” and “Not visible” indicates whether the Bluetooth radio is discoverable or not discoverable by other Bluetooth devices.
Now, you can connect to other transmitting and discoverable Bluetooth devices (see page 10-2).
To make the terminal discoverable, see page 10-6.
10 - 1
DRAFT COPY 11/11/11
Pairing and Trusted Devices
The terminal does support pairing. Pairing happens during general connection setup. Paired devices are
"trusted" devices. This means that there is unrestricted access to all services (including services that
require authorization and authentication).
A connection can exclude pairing. A device that is connected to the terminal but not paired with it is considered an untrusted device. Content can still be passed to untrusted devices by requiring authorization
with each attempt (for example, with the initialization of a file exchange).
Connecting to Other Bluetooth Devices
To connect to other bluetooth devices, you need to perform a device discovery, select a discovered
device, and then connect to the selected device. Pairing happens as part of the connection process.
1. Make sure the bluetooth device is in range and set to be discoverable by other bluetooth devices.
2. In the Dolphin Wireless Manager, tap Menu > Bluetooth Settings.
OR
Tap
> Settings > Bluetooth
3. Tap Add new device. The terminal begins searching for discoverable Bluetooth devices.
10 - 2
DRAFT COPY 11/11/11
4. Select a device from the list and tap Next.
The types of devices in the
vicinity of the radio appear in
the list of discovered devices.
5. You are prompted to enter a passcode.
• If the device has a specific passcode, enter it in the Passcode field and tap Next.
When attempting to connect to a printer or headset with Bluetooth capabilities, the passcode may
default to either 1111 or 0000. If there is no default, consult the device literature for the number.
• If the device does not have a specific passcode, you can enter one in the Passcode field and tap
Next to create a passcode.
6. The Bluetooth radio tries to connect with the device.
7. If you created a passcode, you will be prompted by the other device to enter the same passcode.
Enter the created passcode to establish a paired connection.
If you entered a device specific passcode, you should not have to do anything on the other device.
10 - 3
DRAFT COPY 11/11/11
8. When the connection is complete, a list of matching and supported services on the device appears.
Only the services that are mutually supported on both devices appear in the Partnership Settings
window.
9. Select the services you want to use and tap Save.
The services on the new devices have to be selected or the pairing won’t include those services,
even though the devices are paired. If services are not selected, you will be continually re-prompted
for the passcode from the device.
10. The device appears in the list on the main window.
If you are connecting to a printer or headset, complete any additional steps required by the device.
11. After the passcodes have been accepted on both sides, you have a trusted (paired) connection.
10 - 4
DRAFT COPY 11/11/11
Transferring Files
Before attempting to transfer files, make sure the receiving Bluetooth device is in range, set to be discoverable by other devices, and set to receive incoming beams.
1. Tap
> File Explorer.
2. Navigate to the file you want to transfer.
3. Tap and hold on the file and select Beam File on the popup menu.
4. The Bluetooth radio begins searching for devices.
When a Bluetooth device is first
found, it appears as an
Unknown device; the
icon
indicates that the device is a
Bluetooth device.
As data is retrieved, the device
IDs appear in the list.
5. Tap the device to begin sending the selected file.
6. While trying to connect, the selected device reads “Pending”.
10 - 5
DRAFT COPY 11/11/11
7. When the file is being transferred, the selected device reads “Sending”.
Making the Terminal Discoverable
By default, the Dolphin terminal is not discoverable, which means that the terminal will not be found by
other Bluetooth devices.
1. To make the terminal discoverable, tap
> Settings > Bluetooth
Note: If you are in the Dolphin Wireless Manager, tap Menu > Bluetooth Settings.
2. Tap Mode on the Horizontal scroll.
3. Select “Make this device visible to other devices” and tap OK.
Enabling the Terminal to Receive Incoming Beams
By default, the 7800 terminal is not configured to receive incoming beams from other devices attemting
file transfers via the Beam File command. Before initiating a file transfer from another device follow the
steps below to enable Beam reception on your Dolphin terminal.
1. Tap
> Settings > Connections > Beam.
2. Select “Receive all incoming beams.”
3. Tap OK.
10 - 6
DRAFT COPY 11/11/11
Selecting COM Ports
You can select COM ports 0-9. For more information, see 7800 COM Port Assignment Table on page 811.
10 - 7
DRAFT COPY 11/11/11
10 - 8
11
DRAFT COPY 11/11/11
Working with GPS
Overview
The Dolphin 7800 terminal contains an integrated GPS module that allows location tracking of workers
and vehicles, providing better utilization of field assets. Optional mapping and navigation software provides turn-by-turn driving directions and location information.
Assisted GPS Support
The operating system software does not inhibit nor explicitly support assisted GPS modes, which usually
requires installing a vendor-specific client on the terminal that communicates with the GPS module. This
client would then provide the almanac and/or ephemeris data for warm or hot start modes of operation,
allowing a lower time to first fix (TTFS). The Client must be configured on the terminal, active, and provide the data to the GPS module through the standard COM port.
Powering the GPS Module
The GPS module powers on automatically when accessed by a software application and powers off
automatically when that software application closes. You cannot manually power on and off the GPS
module.
Communication Ports
There are two ways to access the GPS module: through the actual COM port (COM7) or the GPS Intermediate Driver. The method you use depends on the software application you are using. If the software
application requires the actual COM Port, set the operating system to use COM7. If the software application requires the GPS Intermediate Driver, set the operating system to use the GPS Intermediate Driver.
Selecting the Port
1. Tap
> Settings > System > External GPS.
2. In the GPS program port: drop-down list, select COM7 or GPD1
(the GPS Intermediate Driver) as required by the application.
Note: The GPS program port and hardware port cannot be the same value.
3. Tap OK to save.
COM7
COM Port 7 can be set to the following baud rates:
• 4800
• 9600 (Default baud rate. Recommended for optimal performance.)
• 19200
• 38400
Other baud rates are not possible. The baud rate selected on COM7 is the actual baud rate with which
the GPS communicates.
11 - 1
DRAFT COPY 11/11/11
GPS Intermediate Driver
When the first user of GPD1 opens the port, the GPS Intermediate Driver opens the COM7 port. The
GPS Intermediate Driver allows multiple applications to open GPD1, and the GPS data is broadcast to
all open ports.
When the GPSID driver is in use, the COM7 port is allocated to GPSID as READ|WRITE (COM7 is still
available for access mode of 0).
For more information about Microsoft’s GPS Intermediate Driver, follow this link:
http://msdn.microsoft.com/en-us/library/ms850332.aspx
GPS Demo
The GPS Demo demonstrates the main functionality of the integrated GPS module. The GPS Demo
uses COM7.
To see the GPS Demo, tap
11 - 2
> Demos > GPS Demo.
12
DRAFT COPY 11/11/11
Dolphin 7800HomeBase Device (Model 7800-HB)
Overview
The Dolphin 7800 HomeBase (Model 7800-HB) is a charging and communication cradle that supports
USB Hi-Speed 2.0v communication, which enables the terminal to interface with the majority of PCbased enterprise systems. The HomeBase also contains an auxiliary battery well that charges a spare
Honeywell standard or extended battery pack.
The 7800-HB charger is designed for use with battery standard pack models 7800-BTSC or 7800BTSCW (Li-ion 3.7 V, 8.9 watt hour) and extended battery pack 7800-BTXC or 7800-BTXCW ( Li-ion 3.7
V, 14.8 watt hour) manufactured for Honeywell International Inc., and with Dolphin 7800 model terminals.
Warning! The HomeBase is not designed for use in hazardous locations.
We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell
peripherals, cables, or power adapters may cause damage not covered by the warranty.
Unpacking the HomeBase
Open the shipping box and inspect the package to see that the following standard items are included:
• One Dolphin HomeBase, model 7800-HB
• One power supply (see Power on page 12-4)
• One power cord
If any items are missing or anything appears to be damaged, contact your Customer Account Representative. Keep the original packaging in case you need to return the HomeBase for service or to store the
HomeBase while not in use.
Optional Equipment
A standard USB (Type A to B) cable is required when using the HomeBase for communication between
the terminal and a host device.
Charging Overview
The base provides power to the intelligent battery charging system in all Dolphin terminals that senses
when a full charge has been achieved and switches to a trickle charge to maintain the full charge. The
base completes a full charge of the main battery pack installed in the terminal seated in the terminal well
in 4 hours for the standard battery or 6 hours for the extended battery. The base completes a full charge
of the battery pack in the Auxiliary Battery Well (see page 12-2) in 4 hours for the standard battery or 6
hours for the extended battery.
Note: Before attempting to use, charge, or replace the battery in the terminal, you should read the Guidelines for
Battery Pack Use and Disposal on page 3-13.
Communications
Reliable data communications at speeds of up to 480 Mbps can be transmitted by the base through the
Hi-Speed USB port.
Note: These bases cannot be physically connected to each other - sometimes referred to as “daisy-chained”.
12 - 1
DRAFT COPY 11/11/11
Convenient Storage
The intelligent battery charging system makes this base a safe and convenient storage receptacle for
your Dolphin terminal.
Capacity
The base holds one terminal and features an auxiliary battery well behind the terminal well that can
charge a battery pack independently of the terminal well. This means that one base can charge two battery packs: the one installed in the terminal and a spare.
We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in
damage not covered by the warranty.
We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell
peripherals, cables, or power adapters may cause damage not covered by the warranty.
Parts and Functions
Front Panel
Terminal Well
Auxiliary Battery Well
Power/Dock LED
AUX Battery LED
COMM LED
Terminal Well
Place the terminal in this well to communicate with a host device, power the terminal, and
charge the installed battery pack. The base completely charges the main battery in a Dolphin
terminal in 4 hours for the standard battery or 6 hours for the extended battery. If the host
device is a workstation that uses ActiveSync or Windows Device Mobile, synchronization
begins immediately.
Auxiliary Battery Well
See Auxiliary Battery Well on page 12-3.
Power/Dock LED
Indicates if power is supplied to the HomeBase and if a terminal is docked properly in the base.
12 - 2
This color
means…
Red
The HomeBase has power but no terminal is docked.
Green
The HomeBase has power and the terminal is properly seated in the base.
DRAFT COPY 11/11/11
AUX Battery LED
Indicates status of the battery charging in the auxiliary battery well; see Back Panel on page
12-3.
This color
means…
Orange
The auxiliary battery is charging.
Green
The auxiliary battery has completed charging and is ready for use.
Red, Flashing The internal temperature of the auxiliary battery is too hot or there is a battery error.
Charge the auxiliary battery in a cooler environment or replace the battery with a
new Honeywell battery.
For information about charging a battery in the auxiliary battery well, see page 12-5.
COMM LED
This is the communication LED. It indicates the status of data transfer between the Dolphin
terminal and the host device.
This color
means…
Green
A USB Connection is established with the host workstation.
Back Panel
Auxiliary Battery Well
USB Port
DC Power Jack
Auxiliary Battery Well
The base enables you to charge an additional battery pack independently of the terminal well
in 4 hours for the standard battery or 6 hours for the extended battery. This feature ensures
that you can always have a fully-charged battery for your terminal. See Charging a Spare
Battery in the Auxiliary Battery Well on page 12-5.
12 - 3
DRAFT COPY 11/11/11
USB Port
This USB port is USB v2.0 Hi-Speed compliant. Using a USB cable, you can connect the base
to a host device, such as a workstation. USB communication occurs through Microsoft
ActiveSync (v4.5 or higher) or Microsoft Windows Mobile Device Center (WMDC) depending
on the host workstation’s operating system. When the terminal is seated in the terminal well, it
is connected to the host device via the base.
Note:
ActiveSync on your Dolphin terminal works with Windows Mobile Device Center on host
workstations running Windows Vista or Windows 7 and with ActiveSync on host workstations
running Windows XP. For detailed information on ActiveSync and WMDC visit Microsoft's
Windows Mobile Web site.
DC Power Jack
See Power on page 12-4.
Bottom Panel
For details on how to mount the HomeBase, see Mounting the HomeBase on page 12-7.
Compliance Label
Serial Number Label
Power
The base requires 12 Volts DC input for communications, battery charging, and power output to the terminal; the power adapter included with the base converts the voltage from the AC power source to 12
Volts DC. Use only a UL listed power supply, which has been qualified by Honeywell with output rated at
12VDC and 3 amps with the device. The operating temperature range is -10° to 50°C (14° to 122°F)
Honeywell recommends that you leave the base connected to its power source at all times, so that it is
always ready to use.
We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell
peripherals, cables, or power adapters may cause damage not covered by the warranty.
Connecting Power to the HomeBase
1. Plug the A/C power cord into the power
adapter.
2. Plug the power cable into the power connector
on the back of the HomeBase.
3. Plug the A/C power cord into a grounded power
source. The base is now powered. The Power/
Dock LED on the HomeBase illuminates solid
red to indicate the HomeBase has power and
no terminal is docked.
12 - 4
Power Adapter
A/C Power Cord
Power Cable
DRAFT COPY 11/11/11
Charging the Main Battery
The base provides power to the Dolphin terminal and allows the charging of the terminal’s main battery. The intelligent battery charging system incorporated into all Dolphin terminals prevents overcharging, which
means that Dolphin terminals may be stored in the base indefinitely
without damage to the terminals, battery packs, or the base. The base
completes a full charge of the main battery pack installed in the terminal
seated in the terminal well in 4 hours for the standard battery or 6 hours
for the extended battery.
For more information about Honeywell battery packs and how to check
battery power levels in your terminal, refer to Power (page 7-15) and
Batteries (page 3-12).
To Power a Terminal and Charge its Main Battery
1. Install the battery pack in the terminal; see Install the Main Battery
Pack on page 2-1.
2. Verify the base has power. If the Power/Dock LED is not
illuminated, see Connecting Power to the HomeBase on page 12-4.
3. Slide the terminal into the terminal well. The Power/Dock LED
changes to green. The charging begins immediately if required by
the Dolphin terminal.
Ensure all components are dry prior to mating terminals/batteries with peripheral devices. Mating wet
components may cause damage not covered by the warranty.
We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may result in
damage not covered by the warranty.
Charging a Spare Battery in the Auxiliary Battery Well
The auxiliary battery well located on the back of the base charges a spare battery independently of the
terminal well. The Aux Battery LED on the front panel indicates the status of the battery in this well.
Charge time is 4 hours for the standard battery pack or 6 hours for the extended battery pack; see
Auxiliary Battery Well on page 12-3.
1. Insert the battery at an angle.
Note: Align the battery contacts with the contacts inside
the auxiliary battery well.
2. Snap the battery into place with a hinging motion.
The Aux Battery LED lights orange.
3. Use the AUX Battery LED to monitor the charging
progress. The LED lights green when the auxiliary
battery has completed charging and is ready for
use.
Note: If the AUX Battery LED flashes red, the internal
temperature of the battery is too hot or there is a
battery error. Charge the auxiliary battery in a
cooler environment or replace the battery with a new Honeywell Li-ion battery.
12 - 5
DRAFT COPY 11/11/11
Communication
Dolphin terminals support USB communications out of the box. The base also supports USB communications via the USB port located on the back. The base acts as a USB device by interfacing the USB signals of the Dolphin terminal to the USB of the host workstation. Using a standard USB cable, the base’s
USB interface allows the Dolphin terminal to communicate with a workstation.
Requirements
• A base powered by a power cable and power adapter cable
• A standard USB communication cable
• A work station running Windows 98 Second Edition, Windows Me, Windows 2000, Windows NT (4.0
SP6 or higher), Windows XP, Windows Vista, or Windows 7.
• ActiveSync (v4.5 or above) or Widows Mobile Device Center on the workstation
Connecting the Communication Cables
1. Connect power to the HomeBase (see Power on page 12-4).
2. Plug the USB communication cable into the back of the base.
3. Connect the communication cable into the back of the workstation.
4. At this point, the hardware is installed and operating. You may need to reboot your workstation to
complete the installation process.
Establishing Communication
USB communication with the terminal is usually auto-detected and configured by ActiveSync or Windows Mobile Device Center based on the communication cable connected.
Communicating with the Dolphin Terminal
To initiate communications between the Dolphin terminal and peripheral, complete these steps:
1. Insert the Dolphin terminal into the terminal well of the base.
• The DOCK LED illuminates green. If the DOCK LED does not illuminate, make sure that the
terminal is properly seated. You may need to remove and re-insert the terminal.
• The Dolphin terminal activates; if the power is off, the terminal automatically powers on. If the
terminal does not power on, verify that the Honeywell power supply is properly connected to the
cradle and plugged into a functioning outlet.
• If the base is connected to the workstation, the Dolphin terminal automatically opens ActiveSync
or the Windows Mobile Device Center to establish a connection.
2. The base can now transfer data between the terminal and the host device. If communication does
not occur, check the port connections to ensure that the cradle is correctly configured.
Verifying Communication
You can verify that the USB driver is functioning by watching the COMM LED on the USB base. When
the COMM LED illuminates solid green, the base is communicating with the host device.
Note: This base cannot be daisy-chained.
12 - 6
DRAFT COPY 11/11/11
Mounting the HomeBase
Set the base on a dry, stable surface, such as a desktop or workbench near an electrical outlet. Be sure
to provide enough workspace with good lighting for the user to view and operate the Dolphin terminal
while it is in the base. When choosing a mounting location, bear in mind that the location must allow
users' easy access to the Auxiliary Battery Well and the back panel of the HomeBase where the USB
port and the power jack are located.
Optional Hardware Mount
On the bottom of the HomeBase there are four mounting holes with a maximum depth of 7 mm that can
be used to secure the base to a horizontal surface such as a desktop or workbench using M3 self tapping screws.
Optional Mounting Holes for M3
self tapping screws, Qty. 4.
Maximum thread depth of 7 mm.
98 mm
[3.86 in.]
CL
101 mm
[3.98 in.]
90 mm
[3.54 in.]
12 - 7
DRAFT COPY 11/11/11
12 - 8
13
DRAFT COPY 11/11/11
Dolphin 7800eBase Device (Model 7800-EHB)
Overview
The Ethernet Base (eBase) enables a single Dolphin 7800 computer to communicate with a host device
over an Ethernet network.
The 7800-EHB charger is designed for use with standard battery pack model 7800-BTSC or 7800BTSCW (Li-ion 3.7 V, 8.9 watt hour) and extended battery pack model 7800-BTXC or 7800-BTXCW ( Liion 3.7 V, 14.8 watt hour) manufactured for Honeywell International Inc. and with Dolphin 7800 model
terminals.
Warning! The eBase is not designed for use in hazardous locations.
We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell
peripherals, cables, or power adapters may cause damage not covered by the warranty.
Unpacking the eBase
Open the shipping box and inspect the package to see that the following standard items are included:
• One Dolphin eBase Ethernet cradle, model 7800-EHB
• One power supply (see Power on page 13-4)
• One power cord
You will also need to provide a standard CAT-5 Ethernet network cable. These items are needed to set
up and operate the eBase. If any items are missing or anything appears to be damaged, contact your
Customer Account Representative.
Keep the original packaging in case you need to return the eBase for service or to store the eBase while
not in use.
Charging Overview
The base provides power to the intelligent battery charging system in all Dolphin terminals that senses
when a full charge has been achieved and switches to a trickle charge to maintain the full charge. The
base completes a full charge of the main battery pack installed in the terminal seated in the terminal well
in 4 hours for the standard battery or 6 hours for the extended battery. The base completes a full charge
of the battery pack in the Auxiliary Battery Well (see page 13-2) in 4 hours for the standard battery or 6
hours for the extended battery.
Note: Before attempting to use, charge, or replace the battery in the terminal, you should read the Guidelines for
Battery Pack Use and Disposal on page 3-13.
We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in
damage not covered by the warranty.
Convenient Storage
The intelligent battery charging system makes this base a safe and convenient storage receptacle for
your Dolphin terminal.
13 - 1
DRAFT COPY 11/11/11
Capacity
The base holds one terminal and features an auxiliary battery well behind the terminal well that can
charge a battery pack independently of the terminal well. This means that one base can charge two battery packs: the one installed in the terminal and a spare.
Parts and Functions
Front Panel
Terminal Well
Auxiliary Battery Well
Power/Dock LED
AUX Battery LED
COMM LED
Terminal Well
Place the terminal in this well to communicate with a host device, power the terminal, and
charge the installed battery pack. The eBase completely charges the main battery in a Dolphin
terminal in 4 hours for the standard battery or 6 hours for the extended battery.
Auxiliary Battery Well
See Auxiliary Battery Well on page 13-3.
Power/DOCK LED
Indicates if power is supplied to the eBase and if a terminal is docked properly in the base.
This color
means…
Red
The eBase has power but no terminal is docked.
Green
The eBase has power and the terminal is properly seated in the base.
AUX Battery LED
The AUX Battery LED indicates the status of the battery charging in the auxiliary battery well;
see Back Panel on page 13-3.
13 - 2
This color
means…
Orange
The auxiliary battery is charging.
Green
The auxiliary battery has completed charging and is ready for use.
DRAFT COPY 11/11/11
This color
means…
Red Flashing The internal temperature of the auxiliary battery is too hot or there is a battery error.
Charge the auxiliary battery in a cooler environment or replace the battery with a
Honeywell battery.
COMM LED
The COMM LED indicates the status of data transfer between the Dolphin terminal and the
eBase.
Ethernet Communication
When the Dolphin terminal is docked:
This color
and status
means…
Green
Solid
A connection has been established between the Dolphin terminal
and the Ethernet.
Green
Flashing
Data transfer in progress.
USB Communication
When the Dolphin terminal is docked:
This color
and status
means…
Red
Solid
A USB connection has been established between the Dolphin
terminal and the host workstation.
Back Panel
Auxiliary Battery Well
Green LED
Yellow LED
RJ45 Ethernet Port
DC Power Jack
Auxiliary Battery Well
The eBase enables you to charge an additional battery pack independently of the terminal well
in 4 hours for the standard battery or 6 hours for the extended battery. This feature ensures
that you can always have a fully charged battery for your terminal.
13 - 3
DRAFT COPY 11/11/11
USB Port
This USB port is USB v2.0 Hi-Speed compliant. Using a USB cable, you can connect the
eBase to a USB compliant device to facilitate USB communication to and from the terminal.
USB communication occurs through Microsoft ActiveSync (v4.5 or higher) or Microsoft
Windows Mobile Device Center depending on the host workstation’s operating system. When
the terminal is seated in the terminal well, it is connected to the peripheral device via the
eBase.
Note:
ActiveSync on your Dolphin terminal works with Windows Mobile Device Center on host
workstations running Windows Vista or Windows 7 and with ActiveSync on host workstations
running Windows XP. For detailed information on ActiveSync and Windows Mobile Device
Center visit Microsoft's Windows Mobile Web site.
RJ45 Ethernet Port
Use a standard CAT-5 Ethernet cable; you can connect the ebase to an Ethernet-compliant
device to facilitate Ethernet communication to and from the terminal.
This color
and status
means…
Green
Flashing
Data transfer in progress.
Solid
A connection has been established between the Dolphin
terminal and the Ethernet.
Solid
Ethernet is connected at 100T.
Off
Ethernet is connected at 10T.
Yellow
DC Power Jack
See Power, below.
Bottom Panel
For details on how to mount the eBase, see Mounting the eBase on page 13-7.
Compliance L abel
MAC Address Label
erial Number Label
Power
The terminal requires 12 Volts DC input for communications and battery charging; the power adapter on
the power cable converts the voltage from the power source to 12 Volts DC. Use only a UL listed power
supply, which has been qualified by Honeywell with output rated at 12VDC and 3 amps with the device.
The operating temperature range is -10° to 50°C (14° to 122°F). Honeywell recommends that you leave
the eBase connected to its power source at all times, so that it is always ready to use.
We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell
peripherals, cables, or power adapters may cause damage not covered by the warranty.
13 - 4
DRAFT COPY 11/11/11
Connecting Power to the eBase
Power Adapter
1. Plug the A/C power cord into the power
adapter.
2. Plug the power cable into the power connector
on the back of the eBase.
A/C Power Cord
3. Plug the A/C power cord into a grounded power
source. The Power/Dock LED on the eBase
illuminates solid red to indicate the eBase has
power and no terminal is docked.
Power Cable
Charging the Main Battery
The base provides power to the Dolphin terminal and allows the charging of the terminal’s main battery. The intelligent battery charging system incorporated into all Dolphin terminals prevents overcharging,
which means that Dolphin terminals may be stored in the base indefinitely without damage to the terminals, battery packs, or the base. The
base completes a full charge of the main battery pack installed in the
terminal seated in the terminal well in 4 hours for the standard battery
or 6 hours for the extended battery.
For more information about Honeywell battery packs and how to check
battery power levels in your terminal, refer to Power (page 7-15) and
Batteries (page 3-12).
To Power a Terminal and Charge its Main Battery
1. Install the battery pack in the terminal; see Install the Main Battery
Pack on page 2-1.
2. Verify the base has power. If the Power/Dock LED is not
illuminated, see Connecting Power to the eBase on page 13-5.
3. Slide the terminal into the terminal well. The Power/Dock LED
changes to green. Battery charging begins immediately if required
by the Dolphin terminal.
Ensure all components are dry prior to mating terminals/batteries with peripheral devices. Mating wet
components may cause damage not covered by the warranty.
We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may result in
damage not covered by the warranty.
Charging a Spare Battery in the Auxiliary Battery Well
The auxiliary battery well located on the back of the base charges a spare battery independently of the
terminal well. The Aux Battery LED on the front panel indicates the status of the battery in this well.
Charge time is 4 hours for the standard battery pack or 6 hours for the extended battery pack; see
Auxiliary Battery Well on page 13-3.
13 - 5
DRAFT COPY 11/11/11
1. Insert the battery at an angle.
Note: Align the battery contacts with the contacts inside
the auxiliary battery well.
2. Snap the battery into place with a hinging motion.
The Aux Battery LED lights orange.
3. Use the AUX Battery LED to monitor the charging
progress. The LED lights green when the auxiliary
battery has completed charging and is ready for
use.
Note: If the AUX Battery LED flashes red, the internal
temperature of the battery is too hot or there is a
battery error. Charge the auxiliary battery in a
cooler environment or replace the battery with a
new Honeywell Li-ion battery.
Communication
Software Requirements
Before you connect the Dolphin terminal to the eBase, make sure you have the most current software
installed. To check the terminal’s system information, tap
> Power Tools > SysInfo.
Applications on the Dolphin Terminal
Applications running on the Dolphin terminal when it is connected to the eBase should be designed specifically for a partially connected network. For more details, please refer to the Best Practices for Partially
Connected Networks document available at www.honeywellaidc.com.
Establishing Ethernet Communication
Connecting the Dolphin Terminal to the eBase
By default, the Dolphin terminal is configured to obtain IP addresses automatically via DHCP server.
This means that in most cases you would simply plug-and-play the unit.
1. Verify the base has power. If the Power/Dock LED is not illuminated, see Connecting Power to the
eBase on page 13-5.
2. Plug the CAT-5 Ethernet cable into the RJ45 connector on the back of the eBase.
3. Plug the Ethernet cable into the network.
4. Insert the Dolphin into the terminal well. The DOCK LED for the well changes from red to green and
the connection icon on the Dolphin’s title bar changes from x to
Note: Instead of using the default for DHCP assigned IP addresses, the Dolphin terminal can use a statically
assigned IP address. See standard Microsoft Windows Mobile documentation for how to assign a static
IP address to a network adapter. In this case, set a static IP address for the adapter named "SMC95001
USB2.0 FAST Ethernet Drive".
13 - 6
DRAFT COPY 11/11/11
Displaying the eBase and Terminal IP Address
Once the Dolphin terminal has been successfully connected to the eBase, the terminal uses the eBase
IP address. This IP address can be used by any application on the Dolphin terminal.
1. Tap
> Power Tools > Network Utilities > IPConfig.
2. Change the Adapter to SMC95001.
3. On the Input tab, tap the Display full configuration button.
4. The Dolphin terminal retrieves and displays the IP configuration for the entire terminal and eBase.
Locate the IpAddress field in the IP configuration list.
Establishing USB Communication
Dolphin terminal’s support USB communication out of the box. The eBase also supports USB communications using the USB port located on the back panel of the eBase. The eBase acts as a USB device by
interfacing the USB signals of the Dolphin terminal to the USB of the host workstation. Using a standard
USB cable, the ebase’s USB interface allows the Dolphin terminal to communicate with a host workstation.
Setting Up and Connecting the Dolphin Terminal to the eBase
1. Verify the base has power. If the Power/Dock LED is not illuminated, see Connecting Power to the
eBase on page 13-5.
2. Plug the USB communication cable into the USB port on the back of the eBase.
Note: The Dolphin terminal should always be removed from the eBase when connecting or disconnecting the
USB cable.
3. Connect the other end of the USB cable to the host workstation.
4. Insert the Dolphin terminal in the eBase terminal well. The Power/Dock LED changes to green and
the COMM LED illuminates red.
5. The Dolphin terminal activates and automatically opens ActiveSync to establish a connection.
6. The connection icon in the Dolphin’s navigation bar changes from x to
it indicate a successful
connection. The eBase can now transfer data between the terminal and the host device.
Mounting the eBase
Set the eBase on a dry, stable surface, such as a desktop or workbench near an electrical outlet. Be sure
to provide enough workspace with good lighting for the user to view and operate the Dolphin terminal
while it is in the eBase.
When choosing a mounting location, bear in mind that the location must allow users' easy access to the
Auxiliary Battery Well and the back panel of the HomeBase where the USB port, Ethernet port, and the
power jack are located.
13 - 7
DRAFT COPY 11/11/11
Optional Hardware Mount
On the bottom of the HomeBase there are four mounting holes with a maximum depth of 7 mm that can
be used to secure the base to a horizontal surface such as a desktop or workbench using M3 self tapping screws.
Optional Mounting Holes for M3
self tapping screws, Qty. 4.
Maximum thread depth of 7 mm.
98 mm
[3.86 in.]
13 - 8
CL
101 mm
[3.98 in.]
90 mm
[3.54 in.]
14
DRAFT COPY 11/11/11
Dolphin 7800Mobile Base Device (Model 7800-MB)
Overview
The Dolphin Mobile Base charging cradle is designed specifically for in-premise and in-transit data collection applications. The base features a mounting bracket and a cigarette lighter adapter to adapt it to
your environment.
The 7800-MB charger is designed for use with Dolphin 7800 model terminals using standard battery
pack model 7800-BTSC or 7800-BTCW ( Li-ion 3.7 V, 8.9 watt hour) or extended battery pack model
7800-BTXC or 7800-BTXCW (Li-ion 3.7 V, 14.8 watt hour) manufactured for Honeywell International Inc.
Warning! The Mobile Base is not designed for use in hazardous locations.
We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell
peripherals, cables, or power adapters may cause damage not covered by the warranty.
Charging Overview
The base provides power to the intelligent battery charging system in all terminals that senses when a
full charge has been achieved and switches to a trickle charge to maintain the full charge. The base
completes a full charge of the main battery pack in 4 hours for the standard battery pack or 6 hours for
the extended battery pack.
Note: Before attempting to use, charge, or replace the battery in the terminal, you should read the Guidelines for
Battery Pack Use and Disposal on page 3-13.
We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may result in
damage not covered by the warranty.
Convenient Storage
Intelligent battery charging makes the base a safe and convenient storage receptacle for your Dolphin
terminal.
14 - 1
DRAFT COPY 11/11/11
Mobile Base Components
Terminal Well
Mounting Back Plate
Power Adapter
Terminal Locking
Lever
Adapter Power LED
(not in view)
Mounting Back Plate
Used to mount the base to a fixed location.
Terminal Locking Lever
The mobile base has a locking lever on the front. When the lever is in the down position the
terminal in locked in the base. To unlock the terminal push the lever up.
Terminal Well
Place the terminal in this well to charge the main battery pack.
Power Adapter
The mobile charger is equipped with a car adapter cable that can be connected to a vehicle
cigarette lighter outlet.
UL listed power supply
Input: 9V-24VDC, 3.2A
Output: 5VDC 3000mA
Verify that the power source is always within the specified range and observe correct
input voltage polarity. An improper input voltage range or reverse polarity could damage
the power conversion circuitry.
14 - 2
DRAFT COPY 11/11/11
Back Panel and Mounting Brackets
Ball Joint
Pivot Bracket
Base
Mounting Bracket
Turnscrew
Ball Joint
Ball Joints
There are two ball joints: one that is attached to back of the base and one on the mounting
bracket. Both ball joints are inserted into the bracket and secured to mount the base.
Pivot Bracket
The bracket contains the turnscrew and two slots. Ball joints are inserted into each slot and
secured with the turnscrew.
Turnscrew
The turnscrew is located on the side of the pivot bracket. Rotate the turnscrew to secure or
loosen the ball joint slots.
Mounting Bracket
The mounting bracket is what you attach to the mounting surface. It is comprised of a ball joint
and flat disk. The disk contains drill holes you use to secure the base to the mounting surface.
Mounting
The adjustable mounting bracket holds the terminal securely in place and gives the user a variety of
options for mounting the base.
Safety Precautions
Honeywell is not responsible for any damages caused to you, your vehicle, or other individuals due to the
installation of the Dolphin Mobile mount.
Follow these safety precautions when mounting the mobile base:
Never drill into a surface in your vehicle without first consulting a mobile installation professional
experienced with your vehicle type to avoid damaging the vehicle's safety features, gas tank, electrical system or other sensitive vehicle components.
14 - 3
DRAFT COPY 11/11/11
Do not install the Mobile base in an air bag deployment zone. Honeywell assumes no responsibility
of liability for injury or death because of car crashes and/or air bag deployment.
Do not mount the base in a location where it prevents safe operation of the vehicle and/or impedes
the vehicle operator's field of view.
Do not mount the base in a location where the connectors on the bottom panel of the base are not
easily accessible. Be sure to leave enough room for unrestricted cable connections.
The Mobile base is intended for use in an enclosed space protected from the elements. Do not
mount the Mobile base on external vehicle surfaces.
Select a mounting surface that is flat and smooth like the console area in the vehicle located
between the seats.
Installation
Mounting hardware is not included. You must provide the appropriate hardware for your particular application and vehicle type. To ensure a safe installation, consult a mobile installation professional
experienced with your vehicle type.
1. Using the bracket as a template, mark the locations for the mounting screws.
2. Drill the appropriate size pilot holes in the mounting surface.
3. Secure the mounting bracket to the mounting surface using the
appropriate screw type for your application and vehicle type.
4. Loosen the turnscrew.
5. Insert the ball joint of the mounting bracket to the back of the bracket.
6. Insert the ball joint on the back of the base into the other side of the bracket.
7. Tighten the turnscrew to secure both ball joints.
Charging the Main Battery
The mobile base provides power to the Dolphin and allows charging of the main batteries in the terminal.
The main battery charges in 4 hours for the standard battery or 6 hours for the extended battery. The
intelligent battery charging system incorporated into all Dolphin terminals prevents overcharging, which
means that terminal may be seated in the base indefinitely without damage to the terminal, battery pack,
or the base.
For more information about Honeywell battery packs and how to check battery power levels in your terminal, refer to Power (page 7-15) and Batteries (page 3-12).
To Power a Terminal and Charge its Main Battery
Ensure all components are dry prior to mating terminals/batteries with peripheral devices. Mating wet components may cause damage not covered by the warranty.
We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may result in damage not covered by the warranty.
1. Install the main battery pack in the terminal; see Install the Main Battery Pack on page 2-1.
14 - 4
DRAFT COPY 11/11/11
2. Plug the power adapter into the vehicle power outlet (e.g., cigarette lighter outlet).
3. Lift the base locking latch up.
4. Slide the Dolphin into the terminal well and lower the locking latch. Charging begins immediately if
required by the Dolphin terminal.
14 - 5
DRAFT COPY 11/11/11
14 - 6
15
DRAFT COPY 11/11/11
Dolphin 7800ChargeBase Device (Model 7800-CB)
Overview
The 7800 ChargeBase is a 4-slot charging cradle that can power 4 Dolphin terminals, and charge their
main batteries in 4 hours for the standard battery or 6 hours for the extended battery.
The 7800-CB charger is designed for use with Dolphin 7800 model terminals using one of the following
battery pack models: standard battery pack model 7800-BTSC (Li-ion 3.7 V, 8.9 watt hour), extended
battery pack model 7800-BTXC, or extended pack model 7800BTXCW (Li-ion 3.7 V, 14.8 watt hour)
manufactured for Honeywell International Inc.
Warning! The ChargeBase is not designed for use in hazardous locations.
We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any
non-Honeywell peripherals, cables, or power adapters may cause damage not covered by the warranty.
Unpacking the ChargeBase
Open the shipping box and inspect the package to see that the following standard items are included:
• One Dolphin ChargeBase, model 7800-CB
• One power supply (see Power on page 15-3)
• One power cord
These items are needed to operate the ChargeBase. If any items are missing or anything appears to be
damaged, contact your Customer Account Representative. Keep the original packaging in case you
need to return the ChargeBase for service or to store the ChargeBase while not in use.
Charging Overview
The base supplies power to the intelligent battery charging system in all Dolphin terminals, which senses
when a full charge has been achieved and switches to a trickle charge to maintain the full charge.
As battery packs charge, the charging circuitry follows the two-step charging process (CC-CV) that is
recommended for the battery type. The process monitors changes in temperature, current, and voltage.
The main battery of each terminal charges in 4 hours for the standard battery or 6 hours for the extended
battery.
Note: Before attempting to use, charge, or replace the battery in the terminal, you should read the Guidelines for
Battery Pack Use and Disposal on page 3-13.
Convenient Storage
Intelligent battery charging makes this base a safe and convenient storage receptacle for your Dolphin
terminal.
Capacity
The base can hold up to 4 Dolphin terminals. Each charging well charges each terminal independently of
the other wells.
We recommend use of Honeywell Li-Ion battery pack. Use of any non-Honeywell battery may result in damage
not covered by the warranty.
15 - 1
DRAFT COPY 11/11/11
Parts and Functions
Front Panel
Terminal Wells (Qty. 4)
Power/Dock LED (Qty. 4)
Charge LED (Qty. 4)
Terminal Wells
The base contains four terminal wells. Each well has its own dedicated Power/Docking LED
and Charging LED indicator.
Power/Dock LEDs
The Power/Dock LED indicates if the ChargeBase has power and if the terminal is properly
seated in the terminal well. Each terminal well has its own dedicated Power/Dock LED.
This color
means…
Red
The ChargeBase has power but no terminal is docked.
Green
The ChargeBase has power and the terminal is properly seated in the well facilitating
communication between the base and terminal
Charge LEDs
Each terminal well has a dedicated Charge LED located on the front of the base. When a
Dolphin is docked in a terminal well, the Charge LED illuminates green to indicate power is
being applied to the Dolphin. The Battery Icon in the Dolphin window
indicates the
terminal is running on external power. If a battery pack is installed, the battery is charging in
the background.
When the Dolphin is removed from the base, the battery icon indicates the charge level of the
main battery pack, see Icons in the Title Bar on page 2-5. For additional information on how to
check the power levels of the main battery pack and the backup battery, while the terminal is
docked, see Checking Battery Power on page 3-15.
For details on how to charge the terminal using the ChargeBase, see Charging the Main
Battery on page 15-4.
15 - 2
DRAFT COPY 11/11/11
Back Panel
Power Supply Connector
Power Supply Connector
This connector receives input from the power adapter. Plug the power connector cable from
the power adapter into this connector.
Power
The terminal requires 12 Volts DC input for battery charging; the power adapter on the power cable converts the voltage from the power source to 12 volts DC. Use only a UL Listed power supply, which has
been qualified by Honeywell with output rated at 12VDC and 8.5 amps with the device. The operating
temperature range is -10° to 45°C (14° to 113°F).
Honeywell recommends that you leave the ChargeBase connected to its power source at all times, so
that it is always ready to use.
We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell
peripherals, cables, or power adapters may cause damage not covered by the warranty.
Connecting Power to the ChargeBase
1. Plug the A/C power cord into the power adapter.
A/C Power Cord
2. Plug the power connector cable into the power
connector on the back panel of the ChargeBase.
LED
3. Plug the A/C power cord into a standard wall
outlet. The LED on the Power Adapter
illuminates to indicate power.
Power Adapter
4. All of the Power/Dock LEDs illuminate red to
indicate the base has power. Terminal wells with
properly docked Dolphins indicate power with a
green LED.
5. The base is ready to begin charging terminals.
Power Connector Cable
15 - 3
DRAFT COPY 11/11/11
Charging the Main Battery
The base provides power to the Dolphin terminal(s) and
allows charging of the main batteries in the terminals. The
main battery of each terminal charges in 4 hours for the
standard battery or 6 hours for the extended battery. The
intelligent battery charging system incorporated into all
Dolphin terminals prevents overcharging, which means that
Dolphin terminals may be seated in the base indefinitely
without damage to the terminals, battery packs, or the base.
For more information about Honeywell battery packs and
how to check battery power levels in your terminal, refer to
Power (page 7-15) and Batteries (page 3-12).
To Power a Terminal and Charge its Main Battery
1. Install the main battery pack in the terminal; see Install the Main Battery Pack on page 2-1.
2. Verify the base has power. If the Power/Dock LEDs are not illuminated, see Connecting Power to
the ChargeBase on page 15-3.
3. Slide the Dolphin terminal into one of the four terminal wells. The Power/Dock LED for the well
changes to green. Charging begins immediately if required by the Dolphin terminal.
Ensure all components are dry prior to mating terminals/batteries with peripheral devices. Mating wet
components may cause damage not covered by the warranty.
We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may result in
damage not covered by the warranty.
Mounting the ChargeBase
This base should be mounted to a dry, stable surface. When choosing a location, always bear in mind
that:
• The mounting location must allow users easy access to the power connector.
• The base should be oriented so that users can easily see the LEDs.
Bottom Panel
Rubber Feet, Qty. 8
DIN Rail Slot
Mounting Holes for Wall
Mount Bracket Hardware,
Qty. 4
15 - 4
DRAFT COPY 11/11/11
Desk Mounting
The DIN Rail (7.5 X 35 mm) slot on the bottom panel enables secure mounting on a horizontal surface.
Hardware Required
• 3/16 in. dia x 5/8 in. long pan head screw
• 1/2 in. OD x 7/32 in. ID x 3/64 in. thick
• 3/16 in. dia nut
Installing the DIN Rail
1. Slide the DIN Rail into the DIN Rail slot on the bottom panel of the base.
2. Turn the base and DIN Rail right side up.
3. Then, using the appropriate nuts and bolts, secure the DIN Rail to a stable, flat horizontal surface.
DIN Rail (7.5 X 35 mm)
15 - 5
DRAFT COPY 11/11/11
15 - 6
16
DRAFT COPY 11/11/11
Dolphin 7800Net Base Device (Model 7800-NB)
Overview
The Net Base enables up to four Dolphin 7800 mobile computers to communicate with a host device
over an Ethernet network. In addition, the Net Base provides a second RJ45 Ethernet port for connection to an additional device such as a printer, workstation, eBase, or another Net Base.
The 7800-NB charger is designed for use with Dolphin 7800 model terminals using standard battery
pack model 7800-BTSC (Li-ion 3.7 V, 8.9 watt hour) or extended battery pack model 7800-BTXC (Li-ion
3.7 V, 14.8 watt hour), manufactured for Honeywell International Inc.
Warning! The Net Base is not designed for use in hazardous locations.
We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell
peripherals, cables, or power adapters may cause damage not covered by the warranty.
Unpacking the Net Base
Open the shipping box and inspect the package to see that the following standard items are included:
• One Dolphin Net Base Ethernet cradle, model 7800-NB
• One power supply (see Power on page 16-4)
• One power cord
You will also need to provide a standard CAT-5 Ethernet network cable. These items are needed to set
up and operate the Net Base. If any items are missing or anything appears to be damaged, contact your
Customer Account Representative.
Keep the original packaging in case you need to return the Net Base for service or to store the Net Base
while not in use.
Charging Overview
The base supplies power to the intelligent battery charging system in all Dolphin terminals, which senses
when a full charge has been achieved and switches to a trickle charge to maintain the full charge.
As battery packs charge, the charging circuitry follows the two-step charging process (CC-CV) that is
recommended for the battery type. The process monitors changes in temperature, current, and voltage.
The main battery of each terminal charges in 4 hours for the standard battery or 6 hours for the extended
battery.
Convenient Storage
Intelligent battery charging makes this base a safe and convenient storage receptacle for your Dolphin
terminal.
Capacity
The base can hold up to 4 Dolphin terminals. Each charging well charges each terminal independently of
the other wells.
We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in
damage not covered by the warranty.
16 - 1
DRAFT COPY 11/11/11
Parts and Functions
Front Panel
Terminal Wells (Qty. 4)
Power/Dock LED (Qty. 4)
COMM LED (Qty. 4)
Terminal Wells
The Net Base contains four terminal wells. Each well has its own dedicated Power/Dock LED
and COMM LED indicator.
Place the Dolphin terminal in any one of the four wells to communicate with a host device,
power the terminal, and charge the installed battery pack. The Net Base completely charges
the main battery in a Dolphin terminal in 4 hours for the standard battery or 6 hours for the
extended battery.
Power/DOCK LED
Indicates if power is supplied to the Net Base and if a terminal is docked properly in the terminal
well. Each terminal well has its own dedicated Dock LED.
This color
means…
Red
The Net Base has power but no terminal is docked.
Green
The Net Base has power and the terminal is properly seated in the base.
COMM LED
The COMM LED indicates the status of connection and data transfer between the Dolphin
terminal and the Net Base. Each terminal well has its own dedicated COMM LED.
When the Dolphin terminal is docked:
This color
and status
means…
Green
Solid
A connection has been established between the Dolphin terminal
and the Net Base.
Green
Flashing
Data transfer in progress.
Note: The COMM LED does not necessrily indicate the Net Base and terminal are connected to a valid Ethernet
link. For more information, see RJ45 Ethernet Ports on page 16-3.
16 - 2
DRAFT COPY 11/11/11
Back Panel
Green LED (Qty. 1 Per Port)
Yellow LED (Qty. 1 Per Port)
Port 1: 10/100Mbps RJ45 Ethernet Port
DC Power Jack
Port 2: 100Mbps Only RJ45 Ethernet Port
DC Power Jack
This connector receives input from the power adapter. Plug the power connector cable from
the power adapter into this connector, see Power on page 16-4.
RJ45 Ethernet Ports
The Net Base contains two RJ45 Ethernet ports. You can connect the Net Base to an Ethernetcompliant device to facilitate Ethernet communication to and from the terminal by plugging a
standard CAT-5 Ethernet cable into one of the two Ethernet ports provided. The second RJ45
Ethernet port can be used for connection to an additional device such as a printer, workstation,
eBase, or another Net Base.
Note:
The Net Base does not use a Spanning Tree Protocol (STP). When both RJ45 Ethernet ports
are used, do not connect both Net Base interfaces to the same layer 2 LAN.
Note:
Ethernet Port 2 only supports 100Mbps Ethernet connections. Plugging in a 10Mbps connection
into Port 2 may cause other ports to stop working. For 10Mbps connections use Ethernet Port 1.
Each Ethernet port has a dedicated green and yellow status LED.
This color
and status
means…
Green
Flashing
Data transfer is in progress.
Solid
A connection has been established between the Net Base and
the Ethernet.
Solid
Ethernet is connected at 100T.
Off
Ethernet is connected at 10T.
Yellow
Note: The terminal and Ethernet link must be set up properly to allow the terminal to communicate to other devices
and/or the Internet. For more information, see Connecting the Dolphin Terminal to the Net Base on page 16-6.
16 - 3
DRAFT COPY 11/11/11
Bottom Panel
For details on how to mount the Net Base, see Mounting the Net Base on page 16-6.
MAC Address Label
Compliance
Label
Serial Number
Label
Power
The terminal requires 12 Volts DC input for communications and battery charging; the power adapter on
the power cable converts the voltage from the power source to 12 volts DC. Use only a UL Listed power
supply with output rated 12VDC, 8.5A with the device, which has been qualified by Honeywell. The operating temperature range is -10° to 45°C (14° to 113°F).
Honeywell recommends that you leave the Net Base connected to its power source at all times, so that it
is always ready to use.
We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell
peripherals, cables, or power adapters may cause damage not covered by the warranty.
Connecting Power to the Net Base
Power LED
A/C Power Cord
Power
Adapter
Power Connector Cable
1. Plug the A/C power cord into the power adapter.
2. Plug the power connector cable into the power connector on the back of the Net Base.
3. Plug the A/C power cord into a standard wall outlet. The LED on the Power Adapter illuminates to
indicate power.
4. All four Power/Dock LEDs illuminate solid red to indicate the base has power. Terminal wells with
properly docked Dolphins indicate power with a green LED.
5. The base is ready to begin charging terminals.
16 - 4
DRAFT COPY 11/11/11
Charging the Main Battery
The base provides power to the Dolphin terminals and allows
the charging of the main batteries in the terminals. The main
battery of each terminal charges in 4 hours for the standard
battery or
6 hours for the extended battery. The intelligent battery charging system incorporated into all Dolphin terminals prevents
overcharging, which means that Dolphin terminals may be
stored in the base indefinitely without damage to the terminals,
battery packs, or the base.
For more information about Honeywell battery packs and how
to check battery power levels in your terminal, refer to Power
(page 7-15) and Batteries (page 3-12).
To Power a Terminal and Charge its Main Battery
1. Verify the main battery pack is installed in the terminal and the battery lock is engaged, see Install
the Main Battery Pack on page 2-1.
2. Verify the base has power. If the Power/Dock LEDs are not illuminated, see Connecting Power to
the Net Base on page 16-4.
3. Slide the Dolphin terminal into one of the four terminal wells. The Power/Dock LED for the well
changes to green. Charging begins immediately if required by the Dolphin terminal.
Ensure all components are dry prior to mating terminals/batteries with peripheral devices. Mating wet
components may cause damage not covered by the warranty.
We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may result in
damage not covered by the warranty.
Communication
Software Requirements
Before you connect the Dolphin terminal to the Net Base, make sure you have the most current software
installed. To check the terminal’s system information, tap
> Power Tools > SysInfo.
Applications on the Dolphin Terminal
Applications running on the Dolphin terminal when it is connected to the Net Base should be designed
specifically for a partially connected network. For more details, please refer to the Best Practices for Partially Connected Networks document available at www.honeywellaidc.com.
16 - 5
DRAFT COPY 11/11/11
Connecting the Dolphin Terminal to the Net Base
By default, the Dolphin terminal is configured to obtain IP addresses automatically using a DHCP server.
This means that in most cases, you would simply plug-and-play the unit.
1. Verify the base has power. If the Power/Dock LEDs are not illuminated, see Connecting Power to
the Net Base on page 16-4.
2. Plug the CAT-5 Ethernet cable into one of the RJ45 connectors on the back of the Net Base.
3. Plug the Ethernet cable into the network.
4. Insert the Dolphin into one of the terminal wells. The DOCK LED for the well changes from red to
green and the connection icon on the Dolphin’s title bar changes from x to
5. By default, the DHCP server assigns a unique IP address to each of the Dolphin terminals docked in
the Net Base. This IP address can be used by any application on the Dolphin terminal.
Note: Instead of using the default for DHCP assigned IP addresses, the Dolphin terminal can use a statically
assigned IP address. See standard Microsoft Windows Mobile documentation for how to assign a static IP
address to a network adapter. In this case, set a static IP address for the adapter named "SMC95001 USB2.0
FAST Ethernet Drive".
Displaying the Net Base Terminal Well and Dolphin IP Address
Once the Dolphin terminal establishes communication, it uses the unique IP address assigned to the terminal well it is docked in on the Net Base. If four Dolphin terminals are successfully connected, then four
different IP addresses are assigned to the adapter associated with the Dolphin terminal.
1. Tap
> Power Tools > Network Utilities > IPConfig.
2. Change the Adapter to SMC95001.
3. On the Input tab, tap the Display full configuration button.
4. The Dolphin terminal retrieves and displays the IP configuration for the entire Dolphin terminal and
the Net Base terminal well where the Dolphin is docked.
5. Locate the IpAddress field in the IP configuration list.
Mounting the Net Base
Set the Net Base on a dry, stable surface, such as a desktop or workbench near an electrical outlet. Be
sure to provide enough workspace with good lighting for the user to view and operate the Dolphin terminal while it is in the Net Base. When choosing a location, bear in mind that the mounting location must
allow users easy access to the terminal wells, the Ethernet ports, and the power jack.
16 - 6
DRAFT COPY 11/11/11
Bottom Panel
DIN Rail Slot
Rubber Feet, Qty. 8
Optional Mounting Holes for M3 self
tapping screws, Qty. 4. Maximum
thread depth of 7 mm.
Desk Mounting
The DIN Rail (7.5 X 35 mm) slot on the bottom panel enables secure mounting on a horizontal surface.
Hardware Required
• 3/16 in. dia x 5/8 in. long pan head screw
• 1/2 in. OD x 7/32 in. ID x 3/64 in. thick
• 3/16 in. dia nut
Installing the DIN Rail
1. Slide the DIN Rail into the DIN Rail slot on the bottom panel of the base.
2. Turn the base and DIN Rail right side up.
16 - 7
DRAFT COPY 11/11/11
3. Then, using the appropriate nuts and bolts, secure the DIN Rail to a stable, flat horizontal surface.
DIN Rail (7.5 x 35 mm)
16 - 8
17
DRAFT COPY 11/11/11
Dolphin 7800QuadCharger Device (Model 7800-QC)
Overview
This 4-slot charging station provides intelligent battery management for the rechargable battery packs
used in Dolphin terminals.
The 7800-QC charger is designed for use with standard battery pack model 7800-BTSC or 7800BTSCW (Li-ion 3.7 V, 8.9 watt hour) and extended battery pack model 7800-BTXC or 7800-BTXCW (Liion 3.7 V, 14.8 watt hour) manufactured for Honeywell International Inc.
Warning! The QuadCharger is not designed for use in hazardous locations.
We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any
non-Honeywell peripherals, cables, or power adapters may cause damage not covered by the warranty.
Unpacking the QuadCharger
Open the shipping box and inspect the package to see that the following standard items are included:
• One QuadCharger, model 7800-QC
• One power supply (see Power on page 17-3)
• One power cord
These items are needed to operate the QuadCharger. If any items are missing or anything appears to be
damaged, contact your Customer Account Representative. Keep the original packaging in case you
need to return the HomeBase for service or to store the HomeBase while not in use.
Charging Overview
Each charging slot works independently of the other three. As battery packs charge, the charging circuitry follows the two-step charging process (CC-CV) that is recommended for the battery type. The process monitors changes in temperature, current, and voltage and resets the battery pack. Charge time is
4 hours for the standard battery or 6 hours for the extended battery.
Note: Before attempting to use, charge, or replace the battery in the terminal, you should read the Guidelines for
Battery Pack Use and Disposal on page 3-13.
Capacity
The charger holds 4 Honeywell standard or extended batteries.
We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may result in
damage not covered by the warranty.
17 - 1
DRAFT COPY 11/11/11
Parts and Functions
Top Panel
Power Supply
Connector
Support Legs
Qty. 2
Status LEDs
Qty. 1 Per Charging Slot
Charging Slots
Qty. 4
Power LED
Charging Slots
There are four charging slots. Each slot holds one battery and charges it independently of the
other slots. Charging immediately begins when a battery is placed in a slot.
Power LED
The power LED indicates if the QuadCharger is powered. When the QuadCharger is receiving
power, the LED illuminates green.
Power Supply Connector
You attach the power supply to this connector. See Power on page 17-3.
Status LEDs
Each of the four battery slots has a dedicated status LED. The color of the LED indicates the
charge status of the battery in the slot.
Color
This color indicates that the battery in the slot…
Green (Solid)
Has completed its charge cycle and is ready for use.
Orange (Solid)
Is being charged at a maximum charge rate.
Red (Flashing)
The internal temperature of the auxiliary battery is too hot or there
is a battery error. Charge the auxiliary battery in a cooler
environment or replace the battery with a new Honeywell battery.
For more information, see Troubleshooting on page 17-5.
17 - 2
DRAFT COPY 11/11/11
Power
The charger must be connected to a power
source via the Honeywell power adapter cable so
that voltage is adjusted appropriately. Use only a
UL listed power supply, which has been qualified
by Honeywell with output rated at 12VDC and
3 amps with the device.
AC Power Cord
Power Cable
1. Plug the AC power cord into the power
adapter.
2. Plug the power cable into the power
connector on the back of the charger.
Power
Adapter
Power Supply
Connector
Power LED
3. Plug the AC power cord into a grounded
power source.
4. The power LED illuminates green, and the
charger performs a self-diagnostic test that
lasts approximately five seconds.
Recommendations for Storing Batteries
To maintain top performance from batteries, avoid storing batteries outside of the following temperature
ranges:
• 14°F to 113°F (-10°C to +45°C) for short term storage of less than one month
• 32°F to 86°F (-0°C to +30°C) for long term storage
Do not store batteries in extremely high humidity. For prolonged storage, do not keep batteries stored in
a charger that is connected to a power source.
Inserting and Charging Batteries
For best results, battery packs should be at room temperature before recharging them; temperature has
a marked effect on charging. The recommended temperature range is 50°F to 95° F (10°C to 35° C).
Ensure all components are dry prior to mating terminals/batteries with peripheral devices. Mating wet
components may cause damage not covered by the warranty.
We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in
damage not covered by the warranty.
1. Connect power to the charger, see Power above.
2. Insert the battery at an angle.
Note: Align the battery contacts with the contacts inside the
QuadCharger battery well.
3. Snap the battery into place with a hinging motion.
4. The Status LED for that particular slot illuminates
orange to indicate the battery is seated properly and
the charging cycle has begun.
5. When the Status LED turns green, the battery in the slot has completed charging.
17 - 3
DRAFT COPY 11/11/11
Mounting the QuadCharger
The charger should be located on a dry, stable surface and can be mounted on a flat, horizontal surface
such as a desktop or workbench. When choosing a location, always bear in mind that:
• the mounting location must allow users easy access to the power connector.
• the charger should be oriented so that users can easily insert and remove battery packs and see the
status LEDs.
Optional Hardware Mount
Bottom Panel
268.6 mm [10.57 in.]
93 mm [3.66 in.]
45mm
[1.77 in.]
60 mm
[2.36 in.]
90 mm
[3.54 in.]
Optional Mounting Holes
17 - 4
Option
Size
Qty.
6 mm [0.24 in.] Dia. thru hole
for #6 Flat Head Phillips Drywall-to-Wood Screws
Mounting holes for M3 self tapping screws, maximum thread depth of 7 mm
DRAFT COPY 11/11/11
Troubleshooting
If you encounter problems with your QuadCharger device, refer to chart below for possible solutions.
If problems persist, please contact Honeywell Technical Support.
Problem
Issue
The Status LED does not come on when I
insert a battery pack.
Check the power connections; make sure the Power cable is
inserted into the Power supply connector and the battery pack
is properly seated.
The Status LED lights red during charging.
Try to charge the battery in one of the other charging slots. If
the red Status LED comes on again, then the problem is
associated with the battery pack. If the red status stays with the
charging slot, the problem is associated with the charging
circuitry.
The Status LED flashes red without a
battery in the charging slot.
If a battery is in failuare mode (flashing red LED), and that
battery is removed from the charging slot, the slot does not
reset and will continue to flash red. To reset the slot and stop
the flashing red LED, insert a known good battery into the slot
or recycle the power to the QuadCharger.
17 - 5
DRAFT COPY 11/11/11
17 - 6
18
DRAFT COPY 11/11/11
Customer Support
Product Service and Repair
Honeywell International Inc. provides service for all its products through service centers throughout the
world. To obtain warranty or non-warranty service, contact the appropriate location below to obtain a
Return Material Authorization number (RMA #) before returning the product.
North America
Telephone: (800) 782-4263
E-mail: hsmnaservice@honeywell.com
Latin America
Telephone: (803) 835-8000
Telephone: (800) 782-4263
Fax: (239) 263-9689
E-mail: laservice@honeywell.com
Brazil
Telephone: +55 (11) 5185-8222
Fax: +55 (11) 5185-8225
E-mail: brservice@honeywell.com
Mexico
Telephone: 01-800-HONEYWELL (01-800-466-3993)
Fax: +52 (55) 5531-3672
E-mail: mxservice@honeywell.com
Europe, Middle East, and Africa
Telephone: +31 (0) 40 2901 633
Fax: +31 (0) 40 2901 631
E-mail: euroservice@honeywell.com
Hong Kong
Telephone: +852-29536436
Fax: +852-2511-3557
E-mail: apservice@honeywell.com
Singapore
Telephone: +65-6842-7155
Fax: +65-6842-7166
E-mail: apservice@honeywell.com
China
Telephone: +86 800 828 2803
Fax: +86-512-6762-2560
E-mail: apservice@honeywell.com
Japan
Telephone: +81-3-6730-7344
Fax: +81-3-6730-7222
E-mail: apservice@honeywell.com
Online Product Service and Repair Assistance
You can also access product service and repair assistance online at www.honeywellaidc.com.
18 - 1
DRAFT COPY 11/11/11
For ongoing and future product quality improvement initiatives, the 7800 comes equipped with an
embedded device lifetime counter function. Honeywell may use lifetime counter data for future statistical
reliability analysis as well as ongoing quality, repair and service purposes.
Technical Assistance
If you need assistance installing or troubleshooting your device, please call your distributor or the nearest technical support office:
North America/Canada
Telephone: (800) 782-4263
E-mail: hsmnasupport@honeywell.com
Latin America
Telephone: (803) 835-8000
Telephone: (800) 782-4263
E-mail: hsmlasupport@honeywell.com
Brazil
Telephone: +55 (11) 5185-8222
Fax: +55 (11) 5185-8225
E-mail: brsuporte@honeywell.com
Mexico
Telephone: 01-800-HONEYWELL (01-800-466-3993)
E-mail: soporte.hsm@honeywell.com
Europe, Middle East, and Africa
Telephone: +31 (0) 40 7999 393
Fax: +31 (0) 40 2425 672
E-mail: hsmeurosupport@honeywell.com
Hong Kong
Telephone: +852-29536436
Fax: +852-2511-3557
E-mail: aptechsupport@honeywell.com
Singapore
Telephone: +65-6842-7155
Fax: +65-6842-7166
E-mail: aptechsupport@honeywell.com
China
Telephone: +86 800 828 2803
Fax: +86-512-6762-2560
E-mail: aptechsupport@honeywell.com
Japan
Telephone: +81-3-6730-7344
Fax: +81-3-6730-7222
E-mail: aptechsupport@honeywell.com
Online Technical Assistance
You can also access technical assistance online at www.honeywellaidc.com.
18 - 2
DRAFT COPY 11/11/11
Limited Warranty
Honeywell International Inc. ("HII") warrants its products and optional accessories to be free from defects
in materials and workmanship and to conform to HII’s published specifications applicable to the products
purchased at the time of shipment. This warranty does not cover any HII product which is (i) improperly
installed or used; (ii) damaged by accident or negligence, including failure to follow the proper
maintenance, service, and cleaning schedule; or (iii) damaged as a result of (A) modification or alteration
by the purchaser or other party, (B) excessive voltage or current supplied to or drawn from the interface
connections, (C) static electricity or electro-static discharge, (D) operation under conditions beyond the
specified operating parameters, or (E) repair or service of the product by anyone other than HII or its
authorized representatives.
This warranty shall extend from the time of shipment for the duration published by HII for the product at
the time of purchase ("Warranty Period"). Any defective product must be returned (at purchaser’s
expense) during the Warranty Period to HII factory or authorized service center for inspection. No product
will be accepted by HII without a Return Materials Authorization, which may be obtained by contacting
HII. In the event that the product is returned to HII or its authorized service center within the Warranty
Period and HII determines to its satisfaction that the product is defective due to defects in materials or
workmanship, HII, at its sole option, will either repair or replace the product without charge, except for
return shipping to HII.
EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE FOREGOING
WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR WARRANTIES, EITHER EXPRESSED OR
IMPLIED, ORAL OR WRITTEN, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT.
HII’S RESPONSIBILITY AND PURCHASER’S EXCLUSIVE REMEDY UNDER THIS WARRANTY IS
LIMITED TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT WITH NEW OR
REFURBISHED PARTS. IN NO EVENT SHALL HII BE LIABLE FOR INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, AND, IN NO EVENT, SHALL ANY LIABILITY OF HII ARISING IN
CONNECTION WITH ANY PRODUCT SOLD HEREUNDER (WHETHER SUCH LIABILITY ARISES
FROM A CLAIM BASED ON CONTRACT, WARRANTY, TORT, OR OTHERWISE) EXCEED THE
ACTUAL AMOUNT PAID TO HII FOR THE PRODUCT. THESE LIMITATIONS ON LIABILITY SHALL
REMAIN IN FULL FORCE AND EFFECT EVEN WHEN HII MAY HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH INJURIES, LOSSES, OR DAMAGES. SOME STATES, PROVINCES, OR
COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU.
All provisions of this Limited Warranty are separate and severable, which means that if any provision is
held invalid and unenforceable, such determination shall not affect the validity of enforceability of the
other provisions hereof. Use of any peripherals not provided by the manufacturer may result in damage
not covered by this warranty. This includes but is not limited to: cables, power supplies, cradles, and
docking stations. HII extends these warranties only to the first end-users of the products. These
warranties are non-transferable.
The limited duration of the warranty for the Dolphin 7800 is as follows:
• The duration of the limited warranty for terminals with an integrated imager is one year.
• The duration of the limited warranty for touch screens is one year.
• The duration of the limited warranty for the Dolphin 7800 HomeBase device, Dolphin 7800 eBase
device, Dolphin 7800 Net Base device, Dolphin 7800 QuadCharger device, Dolphin 7800 Mobile Base,
and Dolphin 7800 ChargeBase device, is one year.
• The duration of the limited warranty for batteries is one year.
Use of any battery from a source other than Honeywell may result in damage not covered by the
warranty. Batteries returned to Honeywell International Inc. in a reduced state may or not be replaced
under this warranty. Battery life will be greatly increased when following the battery instructions in this
user’s guide.
18 - 3
DRAFT COPY 11/11/11
How to Extend Your Warranty
Honeywell International Inc. offers a variety of service plans on our hardware products. These
agreements offer continued coverage for your equipment after the initial warranty expires. For more
information, contact your Sales Representative, Customer Account Representative, or Product Service
Marketing Manager from Honeywell International Inc., or your Authorized Reseller.
18 - 4
DRAFT COPY 11/11/11
DRAFT COPY 11/11/11
Honeywell Scanning & Mobility
9680 Old Bailes Road
Fort Mill, SC 29707
www.honeywellaidc.com
78-UG Rev (a)
11/11

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Copy, Extract, Print high-res
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Modify Date                     : 2011:11:23 16:58:12+08:00
Create Date                     : 2011:11:23 16:56:19+08:00
Metadata Date                   : 2011:11:23 16:58:12+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - DRAFT_COPY_7800-Users-Guide_11-11-11_Gobi.rtf
Creator                         : Irene
Document ID                     : uuid:5db6c05c-a26c-4ecf-b719-0ece5981ee5a
Instance ID                     : uuid:fec5599c-c1c2-443a-baf5-7a447b47d406
Producer                        : GPL Ghostscript 8.15
Page Count                      : 88
Author                          : Irene

EXIF Metadata provided by EXIF.tools