Honeywell AP100A Access Point User Manual Acc Pt QS 11x17

Honeywell International Inc Access Point Acc Pt QS 11x17

UserMan

Access Point AP-010BT/AP-100BTQuick Start GuideAcc-Pt-QS Rev (c)5/13Preliminary Draft 5/15/13Connecting the Access Point1. Slide the O-ring into the groove in the connector.Note: If you choose not to install the O-ring, the Access Point will be rated to IP41, instead of IP54.2. Turn on the computer (laptop/desktop).3. Plug the interface cable into the Access Point first and then into the appropriate port on the computer.  The Page button blinks when the Access Point is first connected to the host.USB Connection:Page buttonRS232 Connection:Page buttonRS485 Connection:Page buttonLinking a Xenon/Granit Scanner4. Scan the linking bar code on the top of the Access Point to establish a connection between the Access Point and the scanner.  The scanner emits a short beep and flashes the green LED to confirm a connection with the Access Point.  The Access Point’s Page button light turns solid blue.Keyboard Wedge Connection:Page buttonLinking a 4820 Scanner5. Remove the 4820 Linking bar code from the Access Point kit and attach it to the Access Point.  Scan the 4820 Linking bar code to establish a connection between the Access Point and the 4820 scanner.  The scanner emits a short beep and flashes the green LED to confirm a connection with the Access Point.  The Access Point’s Page button remains blue.If you have difficulty connecting with your 4820, it may be due to Code XML software in your scanner.  Scan the following bar code, then scan the 4820 Linking bar code.  These steps may resolve this connection problem.Managing ConnectionsAuto Reconnect ModeBy default, the Access Point is set to Auto Reconnect On, so the scanner begins the relink process immediately, when a con-nection to the Access Point is lost.  If you do not want to relink automatically, scan the Auto Reconnect Off bar code.Code XML Off* Auto Reconnect OnAuto Reconnect OffChanging BatteriesIf the scanner turns off due to a low battery, you can change the battery without losing the link with the Access Point, provided the scanner is in range.  A few seconds after the scanner pow-ers up, the scanner relinks to the Access Point.  Refer to your User’s Guide at www.honeywellaidc.com for additional informa-tion about charging the batteries.Low Power ModeWhen there is no activity within a specified time period, the scanner enters a low power mode.  The default time out period is one  hour.  Pull the scanner’s trigger to power the scanner back up.  If the scanner was linked to the Access Point when it went to “sleep,” it will re-link as long as it is in range.If multiple scanners use the same Access Point, it is possible to inadvertently unlink a scanner that is in “sleep” mode, that has a dead battery, or is in the process of getting a new battery.  To prevent this from happening, you can disable the sleep mode (time out) by scanning the No Time Out bar code below. Unlinking the Scanner from Access PointIf you know that your scanner is not going to be used for a while, you can unlink the scanner by scanning the Unlink Scanner bar code below. No Time Out (0)Unlink ScannerPage ButtonNote: This feature does not apply to 4820 scanners.When you press the Page button on the Access Point, the scanners associated with that Access Point will begin beeping (3 short and 1 long beep).  If you pull the trigger on a scanner that is beeping in response, or press the Page button on the Access Point a second time, all associ-ated scanners will stop beeping.   LED DimmerScan a bar code to set the brightness of your Page button.PagebuttonLED Dimmer OffLED Dimmer - LowLED Dimmer - BrightAdding Carriage Return SuffixIf you want a carriage return (CR) to display after the bar code data on your output scan the Add CR Suffix bar code below.  Scan the Clear All Suffixes bar code to remove suffixes.Standard Product DefaultsThis bar code resets all standard product default settings.Note: Resetting standard defaults disconnects the scanner from the Access Point.  Scan the Linking bar code to re-establish a connection.  Refer to your User’s Guide at www.honeywellaidc.com for additional information about product defaults.Additional ProgrammingThe Access Point has all the programming capability of a Cordless Charge Base.  Refer to Cordless System Operation information in your User’s Guide at www.honeywellaidc.com for programming information.  Add CR SuffixClear All SuffixesStandard Product Default Settings
Required Safety LabelsLabel location for item number, serialnumber, revision information, compli-ance, and safety informationProduct SpecificationsParameter SpecificationDimensions (Typical):Height 1.1 inch (28mm)Length 4.3 inches (109mm)Width 2.8 inches (71mm)Weight 2.3 ounces (66g)Voltage Requirements 5 VDC + 0.5VCurrent Draw100mA @ 5 volts typical300mA @ 5 volts maximumTemperature Ranges:Operating 32° F to +122° F (0° C to +50° C)Storage -40° F to +158° F (-40° C to +70° C)Radio:Frequency 2.4 to 2.5 GHz (ISM Band) Frequency Hopping Bluetooth v.2.1Range - AP-010BT 33 ft. (10m) typicalRange - AP-100BT 328 ft. (100m) typicalData Rate Up to 1MBpsHumidity 5 to 95% non-condensingMechanical DropOperational after 50 drops from 3.28 feet (1 m) to concreteVibration 5G Peak from 22Hz to 300HzESD SensitivityUp to 15kV direct airUp to 8 kV indirect coupling planeTechnical AssistanceContact information for technical support and product service can be found at www.honeywellaidc.com.Limited WarrantyRefer to  www.honeywellaidc.com/warranty_information for your product’s warranty information.Product Agency Compliance - AP-010BT/AP-100BTUSAFCC Part 15 This device complies with part 15 of the FCC Rules.  Operation is subject to the following two conditions:1, This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a res-idential installation.  This equipment generates, uses, and can radiate radio fre-quency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  How-ever, there is no guarantee that interference will not occur in a particular installa-tion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol-lowing measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio or television technician for help.If necessary, the user should consult the dealer or an experienced radio/televi-sion technician for additional suggestions.  The user may find the following booklet helpful: “Something About Interference.”  This is available at FCC local regional offices.  Honeywell is not responsible for any radio or television interfer-ence caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Honeywell.  The correction is the responsibility of the user.  Use only shielded data cables with this system.Caution:  Any changes or modifications made to this equipment not expressly approved by Honeywell may void the FCC authorization to operate this equip-ment.UL StatementUL listed: UL60950-1.CanadaIndustry CanadaThis device complies with Canadian RSS-210.  Operation is subject to the fol-lowing conditions:1. This device may not cause interference.2. This device must accept any interference, including interference that may cause undesired operation.Conformité à la règlementation canadienneCet appareil ISM est conforme à la norme CNR-210 du Canada.  Son fonctionnement est assujetti aux conditions suivantes :1. Cet appareil ne doit pas causer de brouillage préjudiciable.2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le brouillage pouvant causer un fonctionnement indésirable.C-UL StatementC-UL listed: CSA C22.2 No.60950-1-07 for I.T.E product safety.EuropeThe CE marking on the product indicates that this device is in confor-mity with all essential requirements of the 1999/5/EC R&TTE Direc-tive and 2011/65/EU RoHS directive.  In addition, complies to 2006/95/EC Low Voltage Directive, when shipped with recommended power supply.  European contact:Hand Held Products Europe B.V.Nijverheidsweg 9-135627 BT EindhovenThe NetherlandsHoneywell shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.  This equipment is intended for use throughout the European Community and has been assessed to the following standards:EN 300 328EN 301 489-1 EN 301 489-17 EN60950-1Waste Electrical and Electronic Equipment InformationHoneywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIA-MENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and electronic equipment (WEEE).This product has required the extraction and use of natural resources for its pro-duction. It may contain hazardous substances that could impact health and the environment, if not properly disposed.In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will reuse or recycle most of the materials of the product you are disposing in a sound way.The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal waste and invites you to use the appropriate separate take-back systems for product dis-posal.If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration.You may also contact your supplier for more information on the environmental performances of this product.Australia/NZC-Tick StatementConforms to AS/NZS 3548 EMC requirementRussiaProduct Agency Compliance - AP-010BT Class IIBrazilMexicoThis product meets Cofetel approval.Product Agency Compliance - AP-100BT Class IChinaSRRC Radio CertificatePatentsFor patent information, please refer to www.honeywellaidc.com/patents.Modelo: AP-010BT0921-11-6583(01)07898927490089" Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário."DisclaimerHoneywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.  The information in this publication does not represent a commitment on the part of HII.HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the fur-nishing, performance, or use of this material.This document contains proprietary information that is protected by copy-right.  All rights are reserved.  No part of this document may be photocopied, reproduced, or translated into another language without the prior written con-sent of HII. 2010-2013 Honeywell International Inc.  All rights reserved.Other product names or marks mentioned in this document may be trade-marks or registered trademarks of other companies and are the property of their respective owners.Web Address: www.honeywellaidc.com

Navigation menu