Honeywell BT010M 10 Meter BT Module User Manual Voyager 1200g 1202g User s Guide
Honeywell International Inc. 10 Meter BT Module Voyager 1200g 1202g User s Guide
Contents
- 1. User manual
- 2. User Manual
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1663573 |
| Application ID | ajqntTx6DIQZjT8roB3cIw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 245.65kB (3070675 bits) |
| Date Submitted | 2012-03-27 00:00:00 |
| Date Available | 2012-03-27 00:00:00 |
| Creation Date | 2011-09-15 10:16:43 |
| Producing Software | Acrobat Distiller 9.4.5 (Windows) |
| Document Lastmod | 2011-09-15 11:22:17 |
| Document Title | Voyager 1200g/1202g User’s Guide |
| Document Creator | FrameMaker 9.0 |
| Document Author: | Honeywell Scanning & Mobility |
Voyager™ 1200g/1202g Single-Line Laser Scanner User’s Guide ™ ft 15 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII. HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII. © 2010-2011 Honeywell International Inc. All rights reserved. Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies and are the property of their respective owners. Web Address: www.honeywellaidc.com Microsoft® Windows® and the Windows logo are trademarks or registered trademarks of Microsoft Corporation. The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies and are the property of their respective owners. Product Agency Compliance - Voyager 1200g USA FCC Part 15 Subpart B Class B This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio or television technician for help. If necessary, the user should consult the dealer or an experienced radio/ television technician for additional suggestions. The user may find the following booklet helpful: “Something About Interference.” This is available at FCC local regional offices. Honeywell is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Honeywell. The correction is the responsibility of the user. Use only shielded data cables with this system. This unit has been tested with cables less than 3 meters. Cables greater than 3 meters may not meet class B performance. Caution: Any changes or modifications made to this equipment not expressly approved by Honeywell may void the FCC authorization to operate this equipment. UL Statement UL listed: UL60950-1, 2nd Edition. Canada Industry Canada ICES-003 This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Conformité à la règlementation canadienne Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada. Son fonctionnement est assujetti aux conditions suivantes : 1. Cet appareil ne doit pas causer de brouillage préjudiciable. 2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le brouillage pouvant causer un fonctionnement indésirable. C-UL Statement C-UL listed: CSA C22.2 No.60950-1-07, Second Edition. Europe The CE marking indicates compliance to 2004/108/EC EMC Directive with Standards EN55022 CLASS B, EN55024, EN61000-3-2, EN61000-3-3. In addition, complies to 2006/95/EC Low Voltage Directive, when shipped with recommended power supply. For further information please contact: Honeywell Imaging & Mobility Europe BV Nijverheidsweg 9-13 5627 BT Eindhoven The Netherlands Honeywell International Inc. shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive. Waste Electrical and Electronic Equipment Information Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and electronic equipment (WEEE). This product has required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environment, if not properly disposed. In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will reuse or recycle most of the materials of the product you are disposing in a sound way. The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal waste and invites you to use the appropriate separate take-back systems for product disposal. If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration. You may also contact your supplier for more information on the environmental performances of this product. Germany GS Statement GS marked to EN60950-1, Second Edition. Australia/NZ C-Tick Statement Conforms to AS/NZS 3548 EMC requirement Mexico Conforms to NOM-019. Russia Gost-R certificate South Korea This product meets Korean agency approval. Taiwan If the following label is attached to your product, the product meets Taiwan agency approval: BSMI Standard: CNS13438, CNS 14336 依據標準 : CNS13438, CNS14336 International LED Safety Statement LEDs have been tested and classified as “EXEMPT RISK GROUP” to the standard: IEC 62471:2006. CB Scheme Certified to CB Scheme IEC60950-1, Second Edition. Laser Safety Statement LASER LIGHT: DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT. LASERSTRAHLUNG: NICHT IN DEN STRAHL BLICKEN. LASER KLASSE 2. LUMIERE LASER: NE PAS REGARDER DANS LE FAISCEAU. APPAREIL A LASER. DE CLASSE 2 630-650nm, 1mW. This device has been tested in accordance with and complies with IEC60825-1 ed2.0 and 21 CFR 1040.10 and 1040.11, except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. LASER LIGHT, DO NOT STARE INTO BEAM, CLASS 2 LASER PRODUCT, 1.0 mW MAX OUTPUT: 630-650nM. Scanner Laser Beam Wavelength 645 - 660 nm Divergence < 1.5 mrad. per IEC 60825-1 worst case Max power output < 1mw Embedded Laser Wavelength 645- 660 nm Divergence < 1.5 mrad, per IEC 60825-1 worst case Max power output < 10 mw Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Patents For patent information, please refer to www.honeywellaidc.com/patents. Solids and Water Protection The Voyager 1200g has a rating of IP42, immunity of foreign particles and dripping water. Product Agency Compliance - Voyager 1202g and CCB00-010BT Charge Base USA FCC Part 15 Subpart C This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications made to this equipment not expressly approved by Honeywell may void the FCC authorization to operate this equipment. Use only shielded data cables with this system. This unit has been tested with cables less than 3 meters. Cables greater than 3 meters may not meet class B performance. UL Statement UL listed: UL60950-1, Second Edition. Canada Industry Canada This device complies with Canadian RSS-210. Operation is subject to the following conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation. Conformité à la règlementation canadienne Cet appareil ISM est conforme à la norme CNR-210 du Canada. Son fonctionnement est assujetti aux conditions suivantes : 1. Cet appareil ne doit pas causer de brouillage préjudiciable. 2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le brouillage pouvant causer un fonctionnement indésirable. C-UL Statement C-UL listed: CSA C22.2 No.60950-1-07, Second Edition. Europe The CE marking on the product indicates that this device is in conformity with all essential requirements of the 1999/5/EC R&TTE Directive. In addition, complies to 2006/95/EC Low Voltage Directive, when shipped with recommended power supply. For further information, contact: Honeywell Imaging & Mobility Europe BV International Inc. Nijverheidsweg 9-13 5627 BT Eindhoven The Netherlands Honeywell shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive. This equipment is intended for use throughout the European Community and has been assessed to the following standards: EN 300 328 EN 301 489-1 EN 301 489-17 EN60950-1 Waste Electrical and Electronic Equipment Information Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL on waste electrical and electronic equipment (WEEE). This product has required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environment, if not properly disposed. In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will reuse or recycle most of the materials of the product you are disposing in a sound way. The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal waste and invites you to use the appropriate separate take-back systems for product disposal. If you need more information on the collection, reuse, and recycling systems, contact your local or regional waste administration. You may also contact your supplier for more information on the environmental performances of this product. Australia/NZ C-Tick Statement Conforms to AS/NZS 3548 EMC requirements. China SRRC Radio Certificate. CCC safety (CCB00-010BT base only) Japan Complies with Technical Regulations Conformity Certification of Specified Radio equipment. Korea This product meets Korean agency approval. Russia Gost-R certificate Taiwan If the following label is attached to your product, the product meets Taiwan agency approval: BSMI Standard: CNS13438, CNS14336 (Xenon 1902 only) 依據標準 : CNS13438, CNS14336 NCC standard: Low power frequency electric machineries technical standard: LP0002 International LED Safety Statement LEDs have been tested and classified as “EXEMPT RISK GROUP” to the standard: IEC 62471:2006. Radio Technology Class II CB Scheme Certified to CB Scheme IEC 60950-1, Second Edition. Laser Safety Statement LASER LIGHT: DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT. LASERSTRAHLUNG: NICHT IN DEN STRAHL BLICKEN. LASER KLASSE 2. LUMIERE LASER: NE PAS REGARDER DANS LE FAISCEAU. APPAREIL A LASER. DE CLASSE 2 630-650nm, 1mW. This device has been tested in accordance with and complies with IEC60825-1 ed2.0 and 21 CFR 1040.10 and 1040.11, except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. LASER LIGHT, DO NOT STARE INTO BEAM, CLASS 2 LASER PRODUCT, 1.0 mW MAX OUTPUT: 630-650nM. Scanner Laser Beam Wavelength 645 - 660 nm Divergence < 1.5 mrad. per IEC 60825-1 worst case Max power output < 1mw Embedded Laser Wavelength 645- 660 nm Divergence < 1.5 mrad, per IEC 60825-1 worst case Max power output < 10 mw Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Patents For patent information, please refer to www.honeywellaidc.com/patents. Solids and Water Protection The Voyager 1202g has a rating of IP42, immunity of foreign particles and dripping water. Voyager 1200g Safety Label Locations Laser Output Internal Laser Cautions Compliance Markings information, Part Number, and Serial Number information Compliance Markings information Voyager 1202g Safety Label Locations Laser Output Internal Laser Cautions Laser Safety Information Compliance Markings information, Part Number, and Serial Number information Compliance Markings information CCB00-010BT Safety Label Locations Item Number, Serial Number, and Compliance Markings information Compliance Markings information Table of Contents Chapter 1 - Getting Started About This Manual ...................................................... 1-1 Unpacking Your Device............................................... 1-1 Connecting the Device ................................................ 1-2 Connecting with USB ............................................ 1-2 Connecting with Keyboard Wedge ........................ 1-3 Connecting with RS232 Serial Port ....................... 1-6 Connecting with RS485......................................... 1-7 Reading Techniques ................................................... 1-8 Menu Bar Code Security Settings ............................... 1-8 Setting Custom Defaults ............................................. 1-9 Resetting the Custom Defaults ................................. 1-10 Resetting the Factory Defaults .................................. 1-10 Chapter 2 - Programming the Interface Introduction ................................................................. 2-1 Programming the Interface - Plug and Play ................ 2-1 Keyboard Wedge................................................... 2-1 IBM PS2 Keyboard................................................ 2-1 RS232 Serial Port.................................................. 2-1 RS485 ................................................................... 2-2 OPOS Mode .......................................................... 2-3 USB IBM SurePos................................................. 2-4 IBM Secondary Interface....................................... 2-4 USB PC or Macintosh Keyboard ........................... 2-5 USB HID................................................................ 2-5 HID Fallback Mode................................................ 2-5 USB Serial Commands ............................................... 2-6 USB Serial Emulation............................................ 2-6 CTS/RTS Emulation .............................................. 2-6 ACK/NAK Mode..................................................... 2-7 Communication Timeout ....................................... 2-7 NAK Retries........................................................... 2-8 Support BEL/CAN in ACK/NAK............................. 2-8 Verifone® Ruby Terminal Default Settings ..................2-9 Gilbarco® Terminal Default Settings ............................2-9 Honeywell Bioptic Aux Port Configuration .................2-10 Datalogic™ Magellan© Bioptic Aux Port Configuration ............................................2-10 NCR Bioptic Aux Port Configuration ..........................2-10 Wincor Nixdorf Terminal Default Settings..................2-11 Wincor Nixdorf Beetle™ Terminal Default Settings ...2-12 Keyboard Country Layout ..........................................2-13 Keyboard Wedge Modifiers .......................................2-14 ALT Mode ............................................................ 2-14 Keyboard Style .................................................... 2-15 Keyboard Conversion .......................................... 2-16 Keyboard Modifiers .............................................. 2-16 Inter-Scan Code Delay ........................................ 2-17Break Character ......................................... 2-18 Keyboard Wedge Defaults ................................... 2-18 RS232 Modifiers ........................................................2-19 RS232 Baud Rate................................................ 2-19 RS232 Word Length: Data Bits, Stop Bits, and Parity ....................................................... 2-20 RS232 Handshaking ............................................ 2-21 RS232 Timeout .................................................... 2-22 XON/XOFF .......................................................... 2-22 ACK/NAK ............................................................. 2-23 Communication Timeout ...................................... 2-23 NAK Retries ......................................................... 2-24 Support BEL/CAN in ACK/NAK ........................... 2-25 RS232 Defaults.................................................... 2-25 NCR Modifiers ...........................................................2-25 NCR ACK/NAK .................................................... 2-25 Block Check Character ........................................ 2-26 NCR Prefix ........................................................... 2-26 NCR Suffix ........................................................... 2-26 NCR Prefix/Suffix ................................................. 2-27 NCR NOF (Not-on-File) Error .............................. 2-27 Scanner to Bioptic Communication............................2-27 ii Scanner-Bioptic Packet Mode ............................. 2-28 ACK/NAK............................................................. 2-28 Communication Timeout ..................................... 2-28 Chapter 3 - Cordless System Operation How the Cordless Charge Base Works....................... 3-1 Linking the Scanner to a Charge Base ....................... 3-1 Communication Between the Cordless System and the Host.............................................................. 3-2 RF (Radio Frequency) Module Operation ................... 3-2 System Conditions ...................................................... 3-3 Linking Process ..................................................... 3-3 Scanner Is Out of Range....................................... 3-3 Scanner Is Moved Back Into Range...................... 3-3 Out of Range and Back into Range with Batch Mode On......................................... 3-3 Page Button ................................................................ 3-3 About the Battery ........................................................ 3-4 Voyager 1202 Battery Removal .................................. 3-4 Charging Information............................................. 3-4 Battery Recommendations .................................... 3-5 Proper Disposal of the Battery .............................. 3-6 Flash Updates ............................................................. 3-6 Beeper and LED Sequences and Meaning ................. 3-6 Scanner LED Sequences and Meaning ................ 3-6 Base LED Sequences and Meaning ..................... 3-7 Base Power Communication Indicator .................. 3-7 Reset Scanner ............................................................ 3-8 Scanning While in Base Cradle................................... 3-8 Paging ......................................................................... 3-8 Paging Mode ......................................................... 3-8 Paging Pitch ......................................................... 3-9 Error Indicators............................................................ 3-9 Scanner Address......................................................... 3-9 Base Address ............................................................ 3-10 Scanner Modes ......................................................... 3-10 iii Charge Only Mode............................................... 3-10 Linked Modes ...................................................... 3-11 Unlinking the Scanner................................................3-11 Override Locked Scanner ..........................................3-12 Out-of-Range Alarm...................................................3-12 Alarm Sound Type ............................................... 3-12 Alarm Duration ..................................................... 3-12 Scanner Power Time-Out Timer ................................3-13 Batch Mode................................................................3-13 Batch Mode Beep ................................................ 3-14 Batch Mode Quantity ........................................... 3-14 Delete Last Code ................................................. 3-17 Record Counter ................................................... 3-17 Total Records ...................................................... 3-17 Batch Mode Output Order.................................... 3-18 Clear All Codes After Transmission ..................... 3-18 Clear All Codes .................................................... 3-18 Transmit Records Automatically .......................... 3-19 Transmit Records to Host .................................... 3-19 Batch Mode Transmit Delay ................................ 3-20 Scanner Name...........................................................3-20 Using the Scanner with Bluetooth Devices................3-22 Changing the Scanner’s Bluetooth PIN Code...... 3-22 Minimizing Bluetooth/ISM Band Network Activity ......3-22 Auto Reconnect Mode ......................................... 3-23 Maximum Link Attempts ...................................... 3-24 Relink Time-Out ................................................... 3-24 Bluetooth/ISM Network Activity Examples ........... 3-24 Reset Scanner and Base...........................................3-25 Chapter 4 - Input/Output Settings Power Up Beeper ........................................................4-1 Beep on BEL Character...............................................4-1 Good Read and Error Indicators..................................4-2 Beeper – Good Read ............................................. 4-2 Beeper Volume – Good Read................................ 4-2 iv Beeper Pitch – Good Read ................................... 4-3 Beeper - Transmit Order ....................................... 4-3 Beeper Pitch – Error.............................................. 4-3 Beeper Duration – Good Read.............................. 4-4 Number of Beeps – Good Read ............................ 4-4 Number of Beeps – Error ...................................... 4-4 LED Indicators............................................................. 4-6 LED Settings ......................................................... 4-6 LED Brightness ..................................................... 4-8 In-Stand and Out-Of-Stand Settings ........................... 4-8 In-Stand and Out-of-Stand Defaults ...................... 4-9 Presentation Modes .............................................. 4-9 Manual Activation Mode ...................................... 4-10 End Manual Activation After Good Read............. 4-10 Manual Activation Laser Timeout - Button Settings ............................................ 4-11 CodeGate® .......................................................... 4-12 Object Detection Mode........................................ 4-12 End Object Detection After Good Read .............. 4-13 Object Detection Laser Timeout.......................... 4-13 Object Detection Distance................................... 4-14 Character Activation Mode ........................................ 4-14 Activation Character ............................................ 4-14 End Character Activation After Good Read......... 4-15 Character Activation Laser Timeout .................... 4-15 Character Deactivation Mode.................................... 4-16 Deactivation Character........................................ 4-16 Reread Delay ............................................................ 4-17 User-Specified Reread Delay.................................... 4-17 Output Sequence Overview ...................................... 4-17 Require Output Sequence................................... 4-17 Output Sequence Editor ...................................... 4-18 To Add an Output Sequence............................... 4-18 Other Programming Selections ........................... 4-18 Output Sequence Editor ...................................... 4-20 Sequence Timeout .............................................. 4-20 Sequence Match Beeper..................................... 4-21 Partial Sequence ................................................. 4-21 Require Output Sequence ................................... 4-21 No Read.....................................................................4-22 Chapter 5 - Data Editing Prefix/Suffix Overview..................................................5-1 To Add a Prefix or Suffix: ....................................... 5-1 To Clear One or All Prefixes or Suffixes ................ 5-2 To Add a Carriage Return Suffix to All Symbologies............................................ 5-3 Prefix Selections ..........................................................5-3 Suffix Selections ..........................................................5-4 Transmit Alternate Extended ASCII Characters ..........5-4 Function Code Transmit ..............................................5-6 Communication Check Character................................5-6 Intercharacter, Interfunction, and Intermessage Delays..........................................5-7 Intercharacter Delay .............................................. 5-7 User Specified Intercharacter Delay ...................... 5-7 Interfunction Delay ................................................. 5-8 Intermessage Delay ............................................... 5-9 Chapter 6 - Data Formatting Data Format Editor Introduction...................................6-1 To Add a Data Format .................................................6-1 Other Programming Selections.............................. 6-3 Terminal ID Table ........................................................6-4 Data Format Editor Commands ...................................6-4 Move Commands................................................... 6-5 Search Commands ................................................ 6-6 Miscellaneous Commands..................................... 6-7 Data Formatter.............................................................6-8 Data Format Non-Match Error Tone ...................... 6-9 Primary/Alternate Data Formats ................................6-10 Single Scan Data Format Change ....................... 6-10 vi Chapter 7 - Symbologies All Symbologies........................................................... 7-1 Message Length Description....................................... 7-2 Codabar ...................................................................... 7-3 Codabar Concatenation ........................................ 7-4 Code 39....................................................................... 7-7 Code 32 Pharmaceutical (PARAF)........................ 7-9 Full ASCII .............................................................. 7-9 Interleaved 2 of 5 ...................................................... 7-11 NEC 2 of 5................................................................. 7-13 Code 93..................................................................... 7-15 Straight 2 of 5 Industrial (three-bar start/stop) .......... 7-16 Straight 2 of 5 IATA (two-bar start/stop).................... 7-18 Matrix 2 of 5 .............................................................. 7-19 Code 11..................................................................... 7-21 Code 128................................................................... 7-24 ISBT 128 ................................................................... 7-25 GS1-128 .................................................................... 7-31 Telepen ..................................................................... 7-33 UPC-A ....................................................................... 7-35 UPC-A/EAN-13 with Extended Coupon Code........... 7-38 UPC-A Number System 4 Addenda Required .... 7-38 UPC-A Number System 5 Addenda Required .... 7-39 UPC-E0 ..................................................................... 7-41 EAN/JAN-13 .............................................................. 7-45 EAN-13 Beginning with 2 Addenda Required ..... 7-46 EAN-13 Beginning with 290 Addenda Required ......................................... 7-47 EAN-13 Beginning with 378/379 Addenda Required ......................................... 7-47 EAN-13 Beginning with 414/419 Addenda Required ......................................... 7-48 EAN-13 Beginning with 434/439 Addenda Required ......................................... 7-49 EAN-13 Beginning with 977 Addenda Required ......................................... 7-50 vii EAN-13 Beginning with 978 Addenda Required ......................................... 7-50 EAN-13 Beginning with 979 Addenda Required ......................................... 7-51 ISBN Translate .................................................... 7-53 ISSN Translate .................................................... 7-54 EAN/JAN-8 ................................................................7-55 MSI ............................................................................7-58 Plessey Code.............................................................7-60 GS1 DataBar Omnidirectional ...................................7-62 GS1 DataBar Limited.................................................7-63 GS1 DataBar Expanded ............................................7-64 Trioptic Code .............................................................7-65 GS1 Emulation...........................................................7-65 Postal Codes .............................................................7-66 China Post (Hong Kong 2 of 5) ............................ 7-66 Chapter 8 - Interface Keys Keyboard Function Relationships ................................8-1 Supported Interface Keys ............................................8-2 Chapter 9 - Utilities To Add a Test Code I.D. Prefix to All Symbologies .....9-1 Show Software Revision..............................................9-1 Show Data Format.......................................................9-1 Test Menu....................................................................9-2 EZConfig-Scanning Introduction..................................9-2 Installing EZConfig-Scanning from the Web .......... 9-3 Chapter 10 - Serial Programming Commands Conventions...............................................................10-1 Menu Command Syntax ............................................10-1 Query Commands......................................................10-2 Responses ........................................................... 10-3 Serial Trigger Commands..........................................10-4 viii Read Time-Out.................................................... 10-4 Resetting the Standard Product Defaults .................. 10-4 Menu Commands ...................................................... 10-6 Chapter 11 - Product Specifications Voyager 1200g Scanner Product Specifications ....... 11-1 Voyager 1202g Scanner Product Specifications ....... 11-3 CCB00-010BT Charge Base Product Specifications 11-4 CCB00-010BT Charge Base Mounting ..................... 11-6 Standard Cable Pinouts ............................................ 11-7 Keyboard Wedge................................................. 11-7 Serial Output ...................................................... 11-8 RS485 Output ..................................................... 11-9 USB ................................................................... 11-10 Chapter 12 - Maintenance Repairs ...................................................................... 12-1 Maintenance.............................................................. 12-1 Cleaning the Device ............................................ 12-1 Inspecting Cords and Connectors ....................... 12-1 Replacing Cables in Corded Scanners ..................... 12-1 Replacing an Interface Cable in a Corded Scanner ...................................... 12-2 Replacing Cables in Cordless Systems .................... 12-2 Replacing an Interface Cable in a Base .............. 12-2 Troubleshooting a Voyager Scanner......................... 12-3 Troubleshooting a Cordless System ......................... 12-4 Troubleshooting a Base ...................................... 12-4 Troubleshooting a Cordless Scanner .................. 12-5 ix Chapter 13 - Customer Support Appendix A - Reference Charts Symbology Chart ........................................................ A-1 ASCII Conversion Chart (Code Page 1252) ............... A-4 Code Page Mapping of Printed Barcodes .................. A-6 1 Getting Started About This Manual This User’s Guide provides installation and programming instructions for the Voyager 1200g linear scanner. Product specifications, dimensions, warranty, and customer support information are also included. Honeywell bar code scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option indicates the default setting. Unpacking Your Device After you open the shipping carton containing the product, take the following steps: • Check for damage during shipment. Report damage immediately to the carrier who delivered the carton. • Make sure the items in the carton match your order. • Save the shipping container for later storage or shipping. 1-1 Connecting the Device Connecting with USB A scanner or a cordless base can be connected to the USB port of a computer. 1. Connect the appropriate interface cable to the scanner first, then to the computer. Cordless Base USB Connection: 2. 1-2 Make sure the cables are secured in the wireways in the bottom of the cordless base and that the base sits flat on a horizontal surface. 3. The scanner beeps. 4. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols in the back of this manual. The unit defaults to a USB PC Keyboard. Refer to page 2-5 for other USB terminal settings. For additional USB programming and technical information, refer to “USB Application Note,” available at www.honeywellaidc.com. Connecting with Keyboard Wedge A scanner or cordless base can be connected between the keyboard and PC as a “keyboard wedge,” where the scanner provides data output that is similar to keyboard entries. The following is an example of a keyboard wedge connection: 1. Turn off power and disconnect the keyboard cable from the back of the terminal/computer. 1-3 2. Connect the appropriate interface cable to the scanner and to the terminal/computer. only if power supply is included Cordless Base Keyboard Wedge Connection: 3. Make sure the cables are secured in the wireways in the bottom of the cordless base and that the base sits flat on a horizontal surface. 4. Turn the terminal/computer power back on. The scanner beeps. 5. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols in the back of this manual. The scanner beeps once. 1-4 The unit defaults to an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard. A carriage return (CR) suffix is added to bar code data. 1-5 Connecting with RS232 Serial Port 1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the scanner. Note: For the scanner or cordless base to work properly, you must have the correct cable for your type of terminal/computer. only if power supply is included Cordless Base RS232 Serial Port Connection: 1-6 3. Make sure the cables are secured in the wireways in the bottom of the cordless base and that the base sits flat on a horizontal surface. 4. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the connector to the port. 5. Once the scanner or cordless base has been fully connected, power up the computer. This interface programs 9600 baud, 8 data bits, no parity, and 1 stop bit. Connecting with RS485 A scanner or cordless base can be connected for an IBM POS terminal interface. 1. Connect the appropriate interface cable to the device, then to the computer. Cordless Base RS485 Connection: 1-7 2. Make sure the cables are secured in the wireways in the bottom of the cordless base and that the base sits flat on a horizontal surface. 3. Turn the terminal/computer power back on. The scanner beeps. 4. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols in the back of this manual. The scanner beeps once. For further RS485 settings, refer to RS485, page 2-2. Reading Techniques The scanner has a view finder that projects a bright red aiming beam that corresponds to the scanner’s horizontal field of view. The aiming beam should be centered horizontally over the bar code and must highlight all the vertical bars of the bar code. It will not read if the aiming beam is in any other direction. Good Read Bad Read The aiming beam is smaller when the scanner is closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit. Symbologies with larger bars or elements (mil size) should be read farther from the unit. To read single or multiple symbols (on a page or on an object), hold the scanner at an appropriate distance from the target, press the button, and center the aiming beam on the symbol. If the code being scanned is highly reflective (e.g., laminated), it may be necessary to tilt the code up 15° to 18° to prevent unwanted reflection. Menu Bar Code Security Settings Honeywell scanners are programmed by scanning menu bar codes or by sending serial commands to the scanner. If you want to restrict the ability to scan menu codes, you can use the Menu Bar Code Security settings. Please contact the nearest technical support office (see Limited Warranty on page 13-3) for further information. 1-8 Setting Custom Defaults You have the ability to create a set of menu commands as your own, custom defaults. To do so, scan the Set Custom Defaults bar code below before each menu command or sequence you want saved. If your command requires scanning numeric codes from the back cover, then a Save code, that entire sequence will be saved to your custom defaults. Scan the Set Custom Defaults code again before the next command you want saved to your custom defaults. When you have entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults bar code. Set Custom Defaults Save Custom Defaults Note: If using a cordless system, scanning the Save Defaults bar code also causes both the scanner and the base to perform a reset and become unlinked. The scanner must be placed in its base to re-establish the link before any setup codes are entered. See Cordless System Operation beginning on page 3-1 for additional information. You may have a series of custom settings and want to correct a single setting. To do so, just scan the new setting to overwrite the old one. For example, if you had previously saved the setting for Beeper Volume at Low to your custom defaults, and decide you want the beeper volume set to High, just scan the Set Custom Defaults bar code, then scan the Beeper Volume High menu code, and then Save Custom Defaults. The rest of the custom defaults will remain, but the beeper volume setting will be updated. 1-9 Resetting the Custom Defaults If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults bar code below. This resets the scanner to the custom default settings. If there are no custom defaults, it will reset the scanner to the factory default settings. Any settings that have not been specified through the custom defaults will be defaulted to the factory default settings. Activate Custom Defaults Note: If using a cordless system, scanning this bar code also causes both the scanner and the base to perform a reset and become unlinked. The scanner must be placed in its base to re-establish the link before any setup codes are entered. See Cordless System Operation beginning on page 3-1 for additional information. Resetting the Factory Defaults This selection erases all your settings and resets the scanner to the original factory defaults. If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scanner to factory default settings, first scan the Remove Custom Defaults bar code, then scan Activate Defaults. This resets the scanner to the factory default settings. Remove Custom Defaults Activate Defaults Note: If using a cordless system, scanning the Activate Defaults bar code also causes both the scanner and the base to perform a reset and become unlinked. The scanner must be placed in its base to re-establish the link before any setup codes are entered. See Cordless System Operation beginning on page 3-1 for additional information. The Serial Programming Commands, beginning on page 10-1 list the factory default settings for each of the commands (indicated by an asterisk (*) on the programming pages). 1 - 10 2 Programming the Interface Introduction This chapter describes how to program your system for the desired interface. Programming the Interface - Plug and Play Plug and Play bar codes provide instant scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect. Keyboard Wedge If you want your system programmed for an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard, scan the bar code below. Keyboard wedge is the default interface. Note: The following bar code also programs a carriage return (CR) suffix. IBM PC AT and Compatibles with CR Suffix IBM PS2 Keyboard The following bar code programs you scanner for an IBM PS2 keyboard wedge interface with a USA keyboard. Note: The following bar code also programs a carriage return (CR) suffix. IBM PS2 with CR Suffix RS232 Serial Port The RS232 Interface bar code is used when connecting to the serial port of a PC or terminal. The following RS232 Interface bar code also programs a carriage return (CR) and a line feed (LF) suffix, baud rate, and data format as indicated below. Option Setting Baud Rate Data Format 9600 bps 8 data bits, no parity bit, 1 stop bit 2-1 RS232 Interface RS485 Scan one of the following “Plug and Play” codes to program the scanner for an IBM POS terminal interface. Note: After scanning one of these codes, you must power cycle the cash register. IBM Port 5B Interface IBM Port 9B HHBCR-1 Interface IBM Port 17 Interface IBM Port 9B HHBCR-2 Interface Each bar code above also programs the following suffixes for each symbology: Symbology Suffix Symbology Suffix EAN 8 EAN 13 UPC A UPC E 0C 16 0D 0A Code 39 Interleaved 2 of 5 Code 128 * Code 128 ** 00 00 00 00 0A 0D 0A 18 0B 0B 0B 0B * Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B HHBCR-1, and IBM 4683 Port 17 Interfaces **Suffixes programmed for Code 128 with IBM 4683 Port 9 HHBCR-2 Interface 2-2 OPOS Mode The following bar code configures your scanner for OPOS (OLE for Retail Point of Sale) by modifying the following OPOS-related settings: Option Setting Interface Baud Rate RS232 Handshaking RS232 38400 Flow Control, No Timeout XON/XOFF Off ACK/NAK Off 8 Data, 1 Stop, Parity None Data Bits, Stop Bits, and Parity Prefix/Suffix Intercharacter Delay Symbologies Clear All Prefixes and Suffixes Add Code ID and AIM ID Prefix Add CR Suffix Off Enable UPC-A with check digit and number system Enable UPC-E0 with check digit Enable EAN/JAN-8 with check digit Enable EAN/JAN-13 with check digit Enable Code 128 Enable Code 39 Enable OPOS with automatic disable off OPOS Mode 2-3 USB IBM SurePos Scan one of the following “Plug and Play” codes to program the scanner for an IBM SurePos (USB handheld scanner) or IBM SurePos (USB tabletop scanner) interface. Note: After scanning one of these codes, you must power cycle the cash register. USB IBM SurePos (USB Handheld Scanner) Interface USB IBM SurePos (USB Tabletop Scanner) Interface Each bar code above also programs the following suffixes for each symbology: Symbology Suffix Symbology Suffix EAN 8 EAN 13 UPC A UPC E 0C 16 0D 0A Code 39 Interleaved 2 of 5 Code 128 Code 39 00 00 00 00 0A 0D 18 0A 0B 0B 0B 0B IBM Secondary Interface On some older IBM cash registers, it may be necessary to disable the secondary or management interface. In particular, it has been found necessary on IBM registers using the 4690 V2R4 operating system. The following bar codes are used for this purpose. Default = Enable Secondary Interface. *Enable Secondary Interface Disable Secondary Interface 2-4 USB PC or Macintosh Keyboard Scan one of the following codes to program the scanner for USB PC Keyboard or USB Macintosh Keyboard. Scanning these codes also adds a CR and LF. USB Keyboard (PC) USB Keyboard (Mac) USB Japanese Keyboard (PC) USB HID Scan the following code to program the scanner for USB HID bar code scanners. USB HID Bar Code Scanner HID Fallback Mode If you attempt to set a USB interface for your scanner, but the setup fails on the host system, you can program the scanner to fall back to a HID keyboard interface after a set length of time. For example, if the scanner is configured for Serial Emulation Mode, but the host system does not have the correct driver, the scanner would fail. If you set the HID Fallback Mode for a set length of time, for example, 5 minutes, the scanner would change to a HID keyboard interface after 5 minutes of trying to configure as serial emulation. A unique beep sequence indicates that this mode has been entered. While in HID Fallback Mode, the scanner will not scan normal bar codes and sounds a unique beep sequence that indicates the scanner is in Fallback Mode. Menu codes can still be scanned while in HID Fallback Mode, allowing you to change the scanner’s programming. 2-5 Scan the bar code below, then set the length for the HID Fallback (from 060 minutes) by scanning digits from the Programming Chart, then scanning Save. Default = 5 minutes. HID Fallback Mode USB Serial Commands USB Serial Emulation Scan one of the following codes to program the scanner to emulate a regular RS232-based COM Port. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Honeywell website (www.honeywellaidc.com). The driver will use the next available COM Port number. Apple® Macintosh computers recognize the scanner as a USB CDC class device and automatically uses a class driver. Scanning either of these codes also adds a CR and LF. USB Serial Emulation for Windows XP, Windows Server 2003, and later USB Serial Emulation for Windows 2000 Note: No extra configuration (e.g., baud rate) is necessary. CTS/RTS Emulation CTS/RTS Emulation On * CTS/RTS Emulation Off 2-6 ACK/NAK Mode ACK/NAK Mode On * ACK/NAK Mode Off Communication Timeout This allows you to set the length (in milliseconds) for a timeout for the host ACK/NAK response. Scan the bar code below, then set the timeout (from 0-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 2000 ms. Communication Timeout Timeout Retries This setting limits the number of Communication Timeout retries. If the Timeout Retries is set to 0, the transmission is terminated after the initial Communication Timeout. Scan the bar code below, then set the number of retries (from 0-255) by scanning digits from the Programming Chart, then scanning Save. (5 is the recommended setting.) Default = 0. Timeout Retries 2-7 Communication Timeout Beeper This selection programs the scanner to issue an error beep when a communication timeout has occurred. The error beep sound is programmed using Number of Beeps – Error (page 4-4). Default = On. Off * On NAK Retries This selection limits the number of NAK retries that can occur in ACK/NAK mode. Scan the bar code below, then set the number of retries (from 0255) by scanning digits from the Programming Chart, then scanning Save. (5 is the recommended setting.) Default = 0, or disabled. NAK Retries Support BEL/CAN in ACK/NAK This protocol responds to and commands when in ACK/ NAK mode. The scanner sounds an error tone when a command is sent from the host. terminates the transmission. Default = BEL/ CAN Off. BEL/CAN On * BEL/CAN Off 2-8 Verifone® Ruby Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Verifone Ruby terminal. This bar code sets the baud rate to 1200 bps and the data format to 8 data bits, Mark parity, 1 stop bit and RTS/CTS no timeout. It also adds a line feed (LF) suffix and programs the following prefixes for each symbology: Symbology Prefix UPC-A UPC-E EAN-8 EAN-13 FF Verifone Ruby Settings Note: If you are having unexpected results with this programming code, scan the Activate Defaults bar code on page 1-10 first, then scan the programming code above. Gilbarco® Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Gilbarco terminal. This bar code sets the baud rate to 2400 bps and the data format to 7 data bits, even parity, 2 stop bits. It also adds a carriage return (CR) suffix and programs the following prefixes for each symbology: Symbology Prefix UPC-A UPC-E EAN-8 EAN-13 E0 FF Gilbarco Settings Note: If you are having unexpected results with this programming code, scan the Activate Defaults bar code on page 1-10 first, then scan the programming code above. 2-9 Honeywell Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit. Character RTS/CTS with timeout and 232 ACK/NAK are also enabled. Honeywell Bioptic Settings Note: If you are having unexpected results with this programming code, scan the Activate Defaults bar code on page 1-10 first, then scan the programming code above. Datalogic™ Magellan© Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Datalogic Magellan bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit. Datalogic Magellan Bioptic Settings Note: If you are having unexpected results with this programming code, scan the Activate Defaults bar code on page 1-10 first, then scan the programming code above. NCR Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for an NCR bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 9600 bps and the data format to 7 data bits, Even parity, 1 stop bit and Message RTS/CTS with timeout. The following prefixes are programmed for each symbology: Symbology Prefix Symbology Prefix UPC-A UPC-E EAN-8 E0 FF Code 39 Interleaved 2 of 5 All other bar codes B1 B2 B3 EAN-13 2 - 10 NCR Bioptic Settings Note: If you are having unexpected results with this programming code, scan the Activate Defaults bar code on page 1-10 first, then scan the programming code above. Wincor Nixdorf Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf terminal. This bar code sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit. Wincor Nixdorf Terminal Settings Note: If you are having unexpected results with this programming code, scan the Activate Defaults bar code on page 1-10 first, then scan the programming code above. 2 - 11 Wincor Nixdorf Beetle™ Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf Beetle terminal. The following prefixes are programmed for each symbology: Symbology Prefix Code 128 Code 93 Codabar UPC-A UPC-E EAN-8 A0 Symbology EAN-13 GS1-128 Interleaved 2 of 5 Plessey Straight 2 of 5 IATA All other bar codes Prefix Wincor Nixdorf Beetle Settings Note: If you are having unexpected results with this programming code, scan the Activate Defaults bar code on page 1-10 first, then scan the programming code above. 2 - 12 Keyboard Country Layout Scan the appropriate country code below to program the keyboard layout for your country or language. As a general rule, the following characters are supported, but need special care for countries other than the United States: @ | $ # { } [ ] = / ‘ \ < > ~ * United States Arabic Belgium Chinese Finland France Germany Hungary IBM Financial Italy Japan ASCII Korea 2 - 13 Keyboard Country (continued) Russia Slovenia Spain Switzerland (German) Thailand Turkey Q United Kingdom Vietnam Keyboard Wedge Modifiers ALT Mode If your bar code contains special characters from the extended ASCII chart for example, an e with an accent grave (è), you will use ALT Mode. (See Extended ASCII Characters on page A-5.) Note: Scan the ALT mode bar code after scanning the appropriate Keyboard Country code. 2 - 14 If your keystrokes require using the ALT key and 3 characters, scan the 3 Characters bar code. If your keystrokes require the ALT key and 4 characters, scan the 4 Characters bar code. The data is then output with the special character(s). Default = Off. * Off 3 Characters 4 Characters Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock. If you have used Keyboard Conversion settings, they will override any of the following Keyboard Style settings. Default = Regular. Regular is used when you normally have the Caps Lock key off. * Regular Caps Lock is used when you normally have the Caps Lock key on. Caps Lock Shift Lock is used when you normally have the Shift Lock key on (not common to U.S. keyboards). Shift Lock 2 - 15 Autocaps via NumLock bar code should be scanned in countries (e.g., Germany, France) where the Caps Lock key cannot be used to toggle Caps Lock. The NumLock option works similarly to the regular Autocaps, but uses the NumLock key to retrieve the current state of the Caps Lock. Autocaps via NumLock Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent). Emulate External Keyboard Note: After scanning the Emulate External Keyboard bar code, you must power cycle your computer. Keyboard Conversion Alphabetic keyboard characters can be forced to be all upper case or all lowercase. So if you have the following bar code: “abc569GK,” you can make the output “ABC569GK” by scanning Convert All Characters to Upper Case, or to “abc569gk” by scanning Convert All Characters to Lower Case. These settings override Keyboard Style selections. Default = Keyboard Conversion Off. * Keyboard Conversion Off Convert All Characters to Upper Case Convert All Characters to Lower Case Keyboard Modifiers This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode. 2 - 16 Control + ASCII Mode On: The scanner sends key combinations for ASCII control characters for values 00-1F (refer to the ASCII chart for NonPrintable Characters, page A-4). Windows is the preferred mode. All keyboard country codes are supported. DOS mode is a legacy mode, and it does not support all keyboard country codes. New users should use the Windows mode. Windows Mode Prefix/Suffix Off: The scanner sends key combinations for ASCII control characters for values 00-1F (refer to the ASCII chart for Non-Printable Characters, page A-4), but it does not transmit any prefix or suffix information. Default = Control + ASCII Mode Off. Windows Mode Control + ASCII Mode On * Control + ASCII Mode Off DOS Mode Control + ASCII Mode On Windows Mode Prefix/Suffix Off Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off. Numeric Keypad Mode On * Numeric Keypad Mode Off Inter-Scan Code Delay When your keyboard detects that any key is being pressed, released, or held down, the keyboard sends a packet of information known as a “scan code” to your computer. This selection allows you to adjust the delay 2 - 17 between scan codes. Set the length (in milliseconds) for a delay by scanning the bar code below, then setting the delay (from 1-30) by scanning digits from the Programming Chart, then scanning Save. Default = 0 (800 µs). Inter-Scan Code Delay Break Character When your keyboard detects that any key is being pressed, released, or held down, the keyboard sends a packet of information known as a “scan code” to your computer. There are two different types of scan codes: “make codes” and “break codes.” A make code is sent when a key is pressed or held down. A break code is sent when a key is released. The following selections allow you to suppress or transmit the character sequence of the break code. Default = Transmit. Suppress * Transmit Keyboard Wedge Defaults If you want the custom keyboard wedge default settings restored to your scanner, scan the Keyboard Wedge Defaults bar code below. This resets the scanner to the custom default settings (see Setting Custom Defaults on page 1-9). If there are no custom defaults, it will reset the scanner to the factory default settings. Any settings that have not been specified through the custom defaults will be defaulted to the factory default settings. Keyboard Wedge Defaults 2 - 18 RS232 Modifiers RS232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner. Default = 9600. 300 600 1200 2400 4800 * 9600 19200 38400 57,600 115,200 2 - 19 RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications that require use of the full ASCII set, select 8 data bits per character. Default = 8. Stop Bits sets the stop bits at 1 or 2. Default = 1. Parity provides a means of checking character bit patterns for validity. Default = None. 7 Data, 1 Stop, Parity Even 7 Data, 1 Stop, Parity None 7 Data, 1 Stop, Parity Odd 7 Data, 2 Stop, Parity Even 7 Data, 2 Stop Parity None 7 Data, 2 Stop, Parity Odd 8 Data, 1 Stop, Parity Even * 8 Data, 1 Stop, Parity None 8 Data, 1 Stop, Parity Odd 7 Data, 1 Stop, Parity Space 2 - 20 7 Data, 2 Stop, Parity Space 8 Data, 1 Stop, Parity Space 7 Data, 1 Stop, Parity Mark 7 Data, 2 Stop, Parity Mark 8 Data, 1 Stop Parity Mark RS232 Handshaking RS232 Handshaking allows control of data transmission from the scanner using software commands from the host device. When RTS/CTS is turned Off, no data flow control is used. Flow Control, No Timeout: The scanner asserts RTS when it has data to send, and will wait indefinitely for CTS to be asserted by the host. Character-Based Flow Control, No Timeout: The scanner asserts RTS when it has a character to send, and will wait indefinitely for CTS to be asserted by the host Two-Direction Flow Control: The scanner asserts RTS when it is OK for the host to transmit. The host asserts CTS when it is OK for the device to transmit. Flow Control with Timeout: The scanner asserts RTS when it has data to send and waits for a delay (see RS232 Timeout on page 2-22) for CTS to be asserted by the host. If the delay time expires and CTS is not asserted, the device transmit buffer is cleared and scanning may resume. Character-Based Flow Control with Timeout: The scanner asserts RTS when it has a character to send and waits for a delay (see RS232 Timeout on page 2-22) for CTS to be asserted by the host. If the delay time expires 2 - 21 and CTS is not asserted, the device transmit buffer is cleared and scanning may resume. Default = RTS/CTS Off. Flow Control, No Timeout Character-Based Flow Control, No Timeout Two-Direction Flow Control Flow Control with Timeout Character-Based Flow Control with Timeout * RTS/CTS Off RS232 Timeout When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in milliseconds) for a timeout by scanning the bar code below, then setting the timeout (from 1-5100 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 1000 ms (1 second). RS232 Timeout XON/XOFF Standard ASCII control characters can be used to tell the scanner to start sending data (XON/XOFF On) or to stop sending data (XON/XOFF Off). When the host sends the XOFF character (DC3, hex 13) to the scanner, 2 - 22 data transmission stops. To resume transmission, the host sends the XON character (DC1, hex 11). Data transmission continues where it left off when XOFF was sent. Default = XON/XOFF Off. XON/XOFF On * XON/XOFF Off ACK/NAK After transmitting data, the scanner waits for an ACK character (hex 06) or a NAK character (hex 15) response from the host. If ACK is received, the communications cycle is completed and the scanner looks for more bar codes. If NAK is received, the last set of bar code data is retransmitted and the scanner waits for ACK/NAK again. Turn on the ACK/NAK protocol by scanning the ACK/NAK On bar code below. To turn off the protocol, scan ACK/NAK Off. Default = ACK/NAK Off. ACK/NAK On * ACK/NAK Off Communication Timeout This allows you to set the length (in milliseconds) for a timeout for the host ACK/NAK response. Scan the bar code below, then set the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 2000 ms. Communication Timeout Timeout Retries This setting limits the number of Communication Timeout retries. If the Timeout Retries is set to 0, the transmission is terminated after the initial Communication Timeout. Scan the bar code below, then set the 2 - 23 number of retries (from 0-255) by scanning digits from the Programming Chart, then scanning Save. (5 is the recommended setting.) Default = 0. Timeout Retries Communication Timeout Beeper This selection programs the scanner to issue an error beep when a communication timeout has occurred. The error beep sound is programmed using Number of Beeps – Error (page 4-4). Default = On. Off * On NAK Retries This selection limits the number of NAK retries that can occur in ACK/NAK mode. Scan the bar code below, then set the number of retries (from 0255) by scanning digits from the Programming Chart, then scanning Save. (5 is the recommended setting.) Default = 0, or disabled. NAK Retries 2 - 24 Support BEL/CAN in ACK/NAK This protocol responds to and commands when in ACK/ NAK mode. The scanner sounds an error tone when a command is sent from the host. terminates the transmission. Default = BEL/ CAN Off. BEL/CAN On * BEL/CAN Off RS232 Defaults If you want the custom RS232 default settings restored to your scanner, scan the RS232 Defaults bar code below. This resets the scanner to the custom default settings (see Setting Custom Defaults on page 1-9). If there are no custom defaults, it will reset the scanner to the factory default settings. Any settings that have not been specified through the custom defaults will be restored to the factory default settings. RS232 Defaults NCR Modifiers NCR ACK/NAK This is an NCR communication protocol for ACK/NAK processing. Default = NCR ACK/NAK Off. * NCR ACK/NAK Off NCR ACK/NAK On 2 - 25 Block Check Character When this selection is set to Transmit, the NCR Block Check Character (BCC) is expected with incoming messages and transmitted with outgoing messages. Default = Transmit. * Transmit Don’t Transmit NCR Prefix This selection allows you to program an NCR-specific prefix. Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 to find the hex equivalent for the characters you want for the NCR prefix (typically, 02 for STX). Scan the bar code below, then set the hex number (from 0-FF) by scanning digits from the Programming Chart, then scanning Save. Default = 0. NCR Prefix NCR Suffix This selection allows you to program an NCR-specific suffix. Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 to find the hex equivalent for the characters you want for the NCR suffix (typically, 03 for ETX). Scan the bar code below, then set the hex number (from 0-FF) by scanning digits from the Programming Chart, then scanning Save. Default = 0. NCR Suffix 2 - 26 NCR Prefix/Suffix When set to Transmit, both the NCR prefix and suffix are transmitted with bar codes. Usually, prefixes and suffixes are programmed using the Data Editing selections (see Data Editing beginning on page 5-1), however, the following commands override any other prefix/suffix settings. Default = Don’t Transmit. Transmit * Don’t Transmit NCR NOF (Not-on-File) Error A scanner receives an NOF (Not on File) command from the POS whenever it cannot cross-reference the bar code to a price parameter. When set to On, the error tone sounds (set via Number of Beeps – Error, page 4-4) for an NOF, and disables the scanner while the cashier looks up the price manually. When set to Off, no sound is emitted for an NOF. Default = Off. On * Off Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scanners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 Timeout must be set to 3000 in order to communicate with a bioptic scanner. See RS232 Modifiers on page 2-19, and RS232 Timeout on page 2-22 for further information. 2 - 27 Scanner-Bioptic Packet Mode Packet Mode On must be scanned to set the scanner’s format so it is compatible with a bioptic scanner. Default = Packet Mode Off. * Packet Mode Off Packet Mode On ACK/NAK After transmitting data, the scanner waits for an ACK character (hex 06) or a NAK character (hex 15) response from the host. If ACK is received, the communications cycle is completed and the scanner looks for more bar codes. If NAK is received, the last set of bar code data is retransmitted and the scanner waits for ACK/NAK again. Turn on the ACK/NAK protocol by scanning the ACK/NAK On bar code below. To turn off the protocol, scan ACK/NAK Off. Default = ACK/NAK Off. ACK/NAK On * ACK/NAK Off Communication Timeout This allows you to set the length (in milliseconds) for a timeout for the host ACK/NAK response. Scan the bar code below, then set the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 2000 ms. Communication Timeout 2 - 28 3 Cordless System Operation Note: This chapter applies only to cordless scanning systems. It does not apply to corded scanners. How the Cordless Charge Base Works A cordless charge base provides the link between the cordless scanner and the host system. The base contains an interface assembly and an RF communication module. The RF communication module performs the data exchange between the cordless scanner and the interface assembly. The control assembly coordinates the central interface activities including: transmitting/receiving commands and data to/from the host system, performing software activities (parameter menuing, visual indicator support, power-on diagnostics), and data translation required for the host system. The cordless charge base is also a scanner’s battery charger. Refer to Charging Information, page 3-4, for additional information. Linking the Scanner to a Charge Base Turn off power before connecting a base, then power up the computer once the base is fully connected. When the base is connected and powered up, put the scanner in the base to establish a link. The green LED on the base flashes to indicate the scanner’s battery is charging. If the scanner and base have previously been linked, you do not receive any feedback. If this is the first time that the scanner and base are linked, both devices emit a short chirp when their radios link. That indicates that the scanner is linked to the base. Scanner Page Button Base LEDs Charge Base 3-1 To determine if your cordless system is set up correctly, scan one of the sample bar codes in the back of this manual. If the scanner provides a single good read beep and the green LED lights, the scanner has successfully linked to the base. If you receive an error tone and the red LED lights, the scanner has not linked to the base. Refer to page 12-5 for troubleshooting information. Communication Between the Cordless System and the Host The cordless scanner provides immediate feedback in the form of a “good read” indication (a green LED on the scanner and an audible beep) after a bar code is scanned correctly and the base has acknowledged receiving the data. This is possible since the cordless system provides two-way communication between the scanner and the base. When data is scanned, the data is sent to the host system via the base. The cordless scanner recognizes data acknowledgement (ACK) from the base. If it cannot be determined that the data has been properly sent to the base, the scanner issues an error indication. You must then check to see if the scanned data was received by the host system. 1) Good Read 2) ACK from base 3) Base sends data to host RF (Radio Frequency) Module Operation The cordless system uses a two-way Bluetooth® radio to transmit and receive data between the scanner and the base. Designed for point-to-point and multipoint-to-single point applications, the radio operates using a license free ISM band. This band sends relatively small data packets at a fast data rate over a radio signal with randomly changing frequencies. This makes the cordless system highly responsive to a wide variety of data collection applications and resis- 3-2 tant to noisy RF environments. The Bluetooth Class 2 power level provides a communication range of 33 feet (10m) between the scanner and base, depending on the environment. System Conditions The components of the cordless system interact in specific ways as you associate the scanner with its base, as you move a scanner out of range, or bring a scanner back in range. The following information explains the cordless system operating conditions. Linking Process Once a scanner is placed into a cordless charge base, the scanner’s battery charge status is checked, and software automatically detects the scanner and links it to the base depending on the selected link mode. Scanner Is Out of Range The cordless scanner is in communication with its base, even when it is not transmitting bar code data. Whenever the scanner can’t communicate with the base for a few seconds, it is out of range. If the scanner is out of range and you scan a bar code, the scanner issues an error tone indicating no communication with the base. A cordless charge base can also sound an alarm. Refer to Out-of-Range Alarm, page 3-12. Scanner Is Moved Back Into Range The scanner relinks if the scanner or the base have been reset, or the scanner comes back into range. If the scanner relinks, you will hear a single chirp when the relinking process is complete. Refer to Out-of-Range Alarm on page 3-12 for further information. Out of Range and Back into Range with Batch Mode On The scanner may store a number of symbols (approximately 500 U.P.C. symbols; others may vary) when it is out of range and then send them to the base when back in range (see Batch Mode on page 3-13). You will not hear a communication error tone in this mode, but you will hear a short buzz when you press the button if the radio communication is not working. Once the radio connection is made, the scanner produces a series of beeps while the data is being transferred to the base. Page Button When you press the Page button on the base, the scanner associated with that base will begin beeping (3 short and 1 long beep). If you press the button on a scanner that is beeping in response, or press the Page button on the base a second time, the scanner will stop beeping. See Paging on page 3-8 for further information about Page Button settings. 3-3 About the Battery There is a danger of explosion if the batteries are incorrectly replaced. Replace the batteries with only the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the recycle program for batteries as directed by the governing agency for the country where the batteries are to be discarded. Power is supplied to the cordless scanner by a rechargeable battery that is integrated in the scanner handle. Batteries are shipped approximately 30% to 60% charged. The battery should be charged for a minimum of 4 hours before initial use to ensure optimal performance. Voyager 1202 Battery Removal Charging Information The battery is designed to charge while the scanner is positioned in the cordless base unit. Refer to Base LED Sequences and Meaning, page 37, for an interpretation of the Charge Status indicators. Refer to Charge Only Mode (page 3-10) if you need to charge a scanner without linking it to the base. 3-4 The model Voyager 1202g is designed for use with Honeywell battery pack model 100000495 (Li-ion 3.7Vdc, 7.4 watt hour). Place the scanner in the base that is connected to an appropriate power supply. Use only a Listed Limited Power Source (LPS) or Class 2 type power supply with output rated 5 to 5.2Vdc, 1A. Note: If you are powering the base through the interface cable (for example, a USB cable) and not using an external power supply plugged into the aux port, the current available for charging is reduced and the charge time is increased. Battery Recommendations • The battery is a lithium ion cell and can be used without a full charge, and can also be charged without fully discharging, without impacting the battery life. There is no need to perform any charge/discharge conditioning on this type of battery. • Keep the base connected to power when the host is not in use. • Replace a defective battery immediately since it could damage the scanner. • Although your battery can be recharged many times, it will eventually be depleted. Replace it after the battery is unable to hold an adequate charge. • If you are not sure if the battery or charger is working properly, send it to Honeywell International Inc. or an authorized service center for inspection. Refer to Customer Support on page 13-1 for additional information. Caution: The model CCB00-010BT base is designed for use with the Honeywell model Voyager 1202g scanner. Use of any nonHoneywell battery may result in damage not covered by the warranty. Safety Precautions for Lithium Batteries • • • • • • • Do not place batteries in fire or heat the batteries. Do not store batteries near fire or other high temperature locations. Do not store or carry batteries together with metal objects. Do not expose batteries to water or allow the batteries to get wet. Do not connect (short) the positive and negative terminals, of the batteries, to each other with any metal object. Do not pierce, strike or step on batteries or subject batteries to strong impacts or shocks. Do not disassemble or modify batteries. 3-5 ! Caution: Danger of explosion if batteries are incorrectly replaced. Dispose of used batteries according to the recycle program for batteries as directed by the governing agency for the country where the batteries are to be discarded. Proper Disposal of the Battery When the battery has reached the end of its useful life, the battery should be disposed of by a qualified recycler or hazardous materials handler. Do not incinerate the battery or dispose of the battery with general waste materials. You may send the scanner’s battery to us. (postage paid). The shipper is responsible for complying with all federal, state, and local laws and regulations related to the packing, labeling, manifesting, and shipping of spent batteries. Contact the Product Service Department (page 131) for recycling or disposal information. Since you may find that your cost of returning the batteries significant, it may be more cost effective to locate a local recycle/disposal company. Flash Updates The scanner can be flashed either in the base or out of the base, however, it is recommended that you flash the scanner while it is in the base. Flash updates cannot be completed when the scanner is out of the base and the battery is low, or when the scanner is out of range. Beeper and LED Sequences and Meaning The scanner contains LEDs on the top that indicate linking status, decoding state, and battery condition. The base has LEDs on the front that indicate its power up, communication, and battery charge condition. The unit’s audible indicators have meaning as well. The following table lists the indication and cause of the LED illumination and beeps for the scanner and charge base. Scanner LED Sequences and Meaning Note: Pressing the button on the scanner causes the LED to glow red until it communicates successfully with the base. LED Indication Beeper Indication Cause Normal Operation Red Flash Green Flash None 1 beep Battery low Successful communication or linking Failed communication Red, blinking Menu Operation 3-6 Razz or error tone LED Indication Beeper Indication Cause Green Flash Red, blinking 2 beeps Razz or error tone Successful menu change Unsuccessful menu change Base LED Sequences and Meaning The base contains a red LED that indicate the status of the unit and verifies its communication with the host system. The base also has a green LED that indicates the scanner battery charge condition. Red LED - Host Communication Red LED Communication Condition Off USB suspend On continuously Power on, system idle Short blinks. Occurs while transferring data to/from the RF module or the host port. Receiving data Green LED - Scanner Battery Green LED Charge Condition Off Battery not detected or charge suspended Slow flash, 1 second on, 1 second off Pre-charge and charging On continuously Charge complete Fast flash, 300 mSec on, 300 mSec off Charge Error Base Power Communication Indicator To display the power indicator on the base, scan the Base Power Communication Indicator On bar code. To turn off the power indicator, scan the Off bar code. Default = On. * Base Power Communication Indicator On Base Power Communication Indicator Off 3-7 Reset Scanner Scanning this bar code reboots the scanner and causes it to relink with the base. Reset Scanner Scanning While in Base Cradle If you want to be able to scan bar codes while the scanner is in the base cradle, scan the following Scanning in Cradle On bar code. If you want to only allow scanning when the scanner is out of the base cradle, scan Scanning in Cradle Off. Default = Scanning in Cradle On. Scanning in Cradle Off * Scanning in Cradle On Note: When Scanning in Cradle Off is selected, the scanner will not scan any bar codes while it is in the base cradle. It will only scan when removed from the base. Paging Paging Mode By default, the paging button on the base pages the scanner associated with that base. If you want the paging button on your base to be disabled, scan the following Paging Mode Off bar code. When Paging Mode is off, the base will no longer page the scanner when the button is pressed. The 3-8 red LED on the base will remain lit to indicate that Paging Mode is off. (This light will go out when the button is pressed, then back on when it’s released.) Default = Paging Mode On. * Paging Mode On Paging Mode Off Paging Pitch When you press the Page button on the base, the scanner associated with that base will begin beeping (see Page Button on page 3-3). You can set the pitch of the paging beep for the scanner by scanning one of the following bar codes. Default = Low. * Low (1000 Hz) Medium (3250 Hz) High (4200 Hz) Error Indicators Scanner Address Scan the following bar code to determine the address of the scanner you are using. Scanner Address 3-9 Base Address Scan the following bar code to determine the address of the base you are using. Base Address Scanner Modes The Voyager is capable of working with Bluetooth devices other than the CCB00-010BT charge base. Charge Only Mode There may be times when you want to charge your scanner, but not link to the base. For example, if a scanner is linked to a Bluetooth device and you need to charge the scanner, but want to retain your existing link. In order to program the base for Charge Only Mode, you must link a scanner to it. Once the scanner is linked to the base, scan the Charge Only Mode bar code. Any subsequent scanners placed in that base will charge without linking to it. The scanner used to program the base remains linked to the base. To unlink this scanner, scan Unlink Scanner on page 3-11. Charge Only Mode Note: When in Charge Only Mode, the scanner periodically wakes up and beeps. See "Power Up Beeper" on page 4-1 to change this setting. If you want to charge a scanner and link to the base, use Charge and Link Mode. If the base is programmed for Charge Only Mode, you must link a scanner to it first in order to program it for Charge and Link Mode. Scan the linking bar code on the base to link the scanner, then scan Charge and Link Mode. Default = Charge and Link Mode. * Charge and Link Mode 3 - 10 Linked Modes Locked Link Mode and Open Link Mode are the link modes that accommodate different applications. Scan the appropriate bar codes included in the Open Link and Locked Link Mode explanations that follow to switch from one mode to another. Default = Open Link Mode. Locked Link Mode - Single Scanner If you link a scanner to a base using the Locked Link Mode, other scanners are blocked from being linked if they are inadvertently placed into the base. If you do place a different scanner into a base, it will charge the scanner, but the scanner will not be linked. Locked Link Mode (Single Scanner) To use a different scanner, you need to unlink the original scanner by scanning the Unlink Scanner bar code. (See Scanner Modes, page 310.) Open Link Mode - Single Scanner When newly shipped or defaulted to factory settings, a scanner is not linked to a base. A link is established when the scanner is placed into a base. When in Open Link Mode, a new link is established when a new scanner is placed in the base. Each time a scanner is placed into a base, the scanner becomes the linked to the base and the old scanner is unlinked. * Open Link Mode (Single Scanner) Unlinking the Scanner If a base has a scanner linked to it, that scanner must be unlinked before a new scanner can be linked. Once the previous scanner is unlinked, it will no longer communicate with the base. To unlink the scanner from a base, scan the following Unlink Scanner bar code. Unlink Scanner 3 - 11 Override Locked Scanner If you need to replace a broken or lost scanner that is linked to a base, scan the following Override Locked Scanner bar code with a new scanner and place that scanner in the base. The locked link will be overridden, the broken or lost scanner’s link with the base will be removed, and the new scanner will be linked. Override Locked Scanner (Single Scanner) Out-of-Range Alarm If your scanner is out range of the base, an alarm sounds from the scanner. The alarm stops when the scanner is moved closer to the base, when the base connects to another scanner, or when the alarm duration expires. Note: If you are out of range when you scan a bar code, you will receive an error tone even if you do not have the alarm set. You receive the error tone since the data could not be communicated to the base or the host. Alarm Sound Type Set the alarm type for the scanner by scanning the following appropriate bar code. If the alarm is on, the scanner will emit 3 long, high pitched beeps. Default = Alarm Off. * Alarm Off Alarm On Alarm Duration To set the the length of time you want the Out-of-Range alarm to sound, scan the following bar code and then set the time-out duration (from 0-3000 seconds) by scanning digits on the Programming Chart inside the back cover, then scanning Save. Default = 1 sec. Scanner Alarm Duration 3 - 12 Scanner Power Time-Out Timer Note: Scanner Power Time-out Timer only applies to cordless systems. It does not apply to corded scanners. When there is no activity within a specified time period, the scanner enters low power mode. Scan the appropriate scanner power time-out bar code to change the time-out duration (in seconds). Note: Scanning zero (0) is the equivalent of setting no time-out. If the scanner is not activated during the timer interval, the scanner goes into power down mode. Whenever the scanner is activated, the timer is reset. If Scanning While in Base Cradle (page 3-8) is disabled, the scanner will still go into power down mode. Default = 3600 seconds. 0 seconds 200 seconds 400 seconds 900 seconds * 3600 seconds 7200 seconds Note: When the scanner is in power down mode, pull the trigger to power the unit back up. There will be a set of power up beeps and a delay of up to a few seconds for the radio to join. The scanner will then be ready to use. Batch Mode Batch mode is used to store bar code data when a scanner is out of range of its base, or when performing inventory. The data is transmitted to the base once the scanner is back in range or when the records are manually transmitted. 3 - 13 Automatic Batch Mode stores bar code data when the scanner is out of range of the base. The data is automatically transmitted to the base once the scanner is back in range. When the scanner’s buffer space is full, any bar codes scanned generate an error tone. In order to scan bar codes again, the scanner must be moved back into range of the base so data can be transmitted. Inventory Batch Mode stores bar code data, whether or not you are in range of the base. To transmit the stored data to the base, either place the scanner in the base, or scan Transmit Inventory Records (page 3-19). When the scanner’s buffer space is full, any bar codes scanned generate an error tone. In order to scan bar codes again, the data must be transmitted to the base. Default = Batch Mode Off. * Batch Mode Off Automatic Batch Mode Inventory Batch Mode Batch Mode Beep When scanning in Batch Mode, the scanner beeps every time a bar code is scanned. When Batch Mode Beep is On, you will also hear a click when each bar code is sent to the host. If you do not want to hear these clicks, scan Batch Mode Beep Off. Default = Batch Mode Beep On. Batch Mode Beep Off * Batch Mode Beep On Batch Mode Quantity When in Inventory Batch Mode (page 3-14), you may wish to transmit the number of multiple bar codes scanned, rather than a single bar code multiple times. For example, if you scan three bar codes called XYZ with Batch Mode Quantity Off, when you transmit your data it will appear as XYZ 3 - 14 three times. Using Batch Mode Quantity On and the Quantity Codes (page 3-16), you could output your data as “XYZ, 00003” instead. Default = Batch Mode Quantity Off. * Batch Mode Quantity Off Batch Mode Quantity On Entering Quantities Quantity Codes (page 3-16) allow you to enter a quantity for the last item scanned, up to 9999 (default = 1). Quantity digits are shifted from right to left, so if a 5th digit is scanned, the 1st digit scanned is discarded and the 2nd, 3rd and 4th digits are moved to the left to accommodate the new digit. For example, if the Quantity 5 bar code is scanned after the quantity has been set to 1234, then the 1 is dropped, the quantity will be 2345. Example: Add a quantity of 5 for the last item scanned. 1. Scan the item's bar code. 2. Scan the quantity 5 bar code. Example: Add a quantity of 1,500 for the last item scanned. 1. Scan the item's bar code. 2. Scan the quantity 1 bar code. 3. Scan the quantity 5 bar code. 4. Scan the quantity 0 bar code. 5. Scan the quantity 0 bar code. Example: Change a quantity of 103 to 10. To correct an incorrect quantity, scan the quantity 0 bar code to replace the incorrect digits, then scan the correct quantity bar codes. 1. 2. 3. 4. Scan the quantity 0 bar code to change the quantity to 1030. Scan the quantity 0 bar code to change the quantity to 0300. Scan the quantity 1 bar code to change the quantity to 3001. Scan the quantity 0 bar code to change the quantity to 0010. 3 - 15 Quantity Codes 3 - 16 Delete Last Code If you want to delete the last bar code scanned when in Batch Mode, scan Delete Last Code. Delete Last Code Record Counter If you wish to add a record counter to each bar code scanned in Batch Mode, scan Record Counter On. Your batch output would add a sequential number before each bar code, for example: 00001,bar code 1 00002,bar code 2 Default = Record Counter Off. * Record Counter Off Record Counter On Total Records If you wish to output the total number of bar codes scanned when in Batch Mode, scan Total Records. Total Records 3 - 17 Batch Mode Output Order When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in last-out). Batch Mode FIFO Batch Mode LIFO Clear All Codes After Transmission If you want to clear the scanner’s buffer of all data accumulated in Batch Mode after the data has been transmitted to the host system, scan Clear All Codes After Transmission. If you do not want the buffer cleared after transmission, scan Don’t Clear All Codes After Transmission. Default = Don’t Clear All Codes After Transmission. * Don’t Clear All Codes After Transmission Clear All Codes After Transmission Clear All Codes If you want to clear the scanner’s buffer of all data accumulated in Batch Mode, scan Clear All Codes. Clear All Codes 3 - 18 Transmit Records Automatically If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 3-14), you can transmit all stored data to the host system when the scanner is placed in the base. If you don’t want the records transmitted when the scanner is placed in the base, scan the Don’t Transmit Records Automatically bar code. Default = Don’t Transmit Records Automatically. * Don’t Transmit Records Automatically Transmit Records Automatically Transmit Records to Host If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 3-14), and your scanner is set to Don’t Transmit Records Automatically, you must scan the following bar code to transmit all stored records to the host system. Transmit Inventory Records 3 - 19 Batch Mode Transmit Delay Sometimes when accumulated scans are sent to the host system, the transmission of those scans is too fast for the application to process. To program a transmit delay between accumulated scans, scan one of the following delays. Default = Off. Note: In most cases, a short (250 ms (milliseconds)) delay is ideal, however, longer delays may be programmed. Contact Technical Support (page 13-3) for additional information. * Batch Mode Transmit Delay Off (No Delay) Batch Mode Transmit Delay Short (250 ms) Batch Mode Transmit Delay Medium (500 ms) Batch Mode Transmit Delay Long (1000 ms) Scanner Name You may assign a name to each scanner you are using for identification purposes. The default name is “Voyager.” Perform the rename operation using either the bar codes on page 3-21, or by sending the serial command :Voyager:BT_NAMname. where name is the new name for the scanner. If you wish to change the names of additional scanners, link them to the base one at a time and repeat the :Voyager:BT_NAMname. command for each scanner. 3 - 20 To rename scanners with sequential, numeric names, scan the following bar codes. Scan the Reset code after each name change and wait for the scanner to relink to the base. 0001 0002 0003 0004 0005 0006 0007 Reset You may also scan the following Scanner Name bar code and scan up to 30 numbers and/or letters for the scanner name. For example, if you wanted to name the linked scanner “312,” you would scan the following bar code, scan the 3, 1, and 2 bar codes on the Programming Chart inside the back cover of this manual, then scan Save. Scan the Reset bar code and wait for the scanner to relink to the base. To output the name of the scanner, scan the following bar code. The name will be output showing the product name, model number, and the scanner’s 10-digit serial number. Scanner Name 3 - 21 Using the Scanner with Bluetooth Devices The scanner can be used either with the CCB00-010BT charge base or with other Bluetooth devices. Those devices include personal computers and laptops. Scanning the following Non-Base BT Connection bar code allows the scanner to be used with other Bluetooth devices (e.g., PC/laptop). After you scan the Non-Base BT Connection bar code, follow the instructions supplied with your Bluetooth device to locate the scanner and connect to it. Note: If you go out of range with your scanner, the scanner will not reconnect to the Bluetooth device when it is back in range. To relink to the charge base, scan the Base BT Connection bar code. Non-Base BT Connection Base BT Connection Changing the Scanner’s Bluetooth PIN Code Some devices require a PIN code as part of the Bluetooth security features. Your scanner’s default PIN is 0000, which you may need to enter the first time you connect to your non-base Bluetooth device. To change the PIN, scan the following bar code and then scan the appropriate numeric bar codes from the Programming Chart inside the back cover of this manual. (The PIN code must be between 1 and 16 characters.) Scan Save to save your selection. Default = 0000. Bluetooth PIN Minimizing Bluetooth/ISM Band Network Activity The following settings can help you customize the relinking behavior of the cordless system to obtain the best compromise between convenience and low interference. Note: ISM band refers to the 2.4 to 2.48 GHz frequency band used by wireless networks, cordless phones, and Bluetooth. 3 - 22 Auto Reconnect Mode Auto Reconnect controls whether or not the scanner automatically begins the relink process when a loss of connection is detected. When the Auto Reconnect On bar code is scanned, the scanner begins the relink process immediately, without user intervention. Default = Auto Reconnect On. * Auto Reconnect On Auto Reconnect Off The following table shows the results of the Auto Reconnect On and Off settings: Event Auto Reconnect On Auto Reconnect Off Scanner out of range Relink occurs automatically. If maximum number of link attempts is unsuccessful, then the scanner must be relinked by either pressing the scanner’s button or placing the scanner in the base. (See Maximum Link Attempts on page 3-24.) The scanner is relinked by pressing the button. Base reset (firmware upgrade or power cycle) Scanner behaves as if out of range. No attempt to relink made while base is powered off. Button must be pressed to initiate relinking. Scanner reset due to firmware upgrade Relink occurs automatically. Scanner reset due to battery change Relink occurs automatically. Scanner placed in different base unit Relink to new base occurs automatically. 3 - 23 Maximum Link Attempts The Maximum Link Attempts setting controls the number of times the scanner tries to form a connection with a base. During the connection setup process, the scanner transmits in order to search for and connect to a base. In order to prevent continuous transmissions that could interfere with other users of the ISM band, the number of attempts to connect is limited by this setting. After the maximum number of attempts is reached, the scanner will not attempt to reconnect to a base. Pressing the scanner’s button or placing the scanner in the cradle resets the attempt count and the scanner will again try to link. Scan the Maximum Link Attempts bar code, then scan the number of attempts for the setting (from 0-255) from the inside back cover. Scan Save to save the setting. Default = 0. Maximum Link Attempts Note: When Auto Reconnect Mode is On, setting Maximum Link Attempts to zero will cause the scanner to try to link until the Power Time-Out Timer setting (see page 3-13) expires. When Auto Reconnect Mode is Off, setting Maximum Link Attempts to zero will cause the scanner to only attempt linking one time after a trigger pull. Relink Time-Out Relink Time-Out controls the idle time between relink attempts. An attempt to link a scanner to a base typically lasts up to 5 seconds. This is the time when the scanner is actually attempting a contact . Relink Time-Out controls the amount of time, in seconds, that elapses between the end of one connection attempt and the start of the next. Scan the Relink Time-Out bar code, then scan the number of seconds for the setting (from 1-100) from the inside back cover. Scan Save to save the setting. Default = 3 seconds. Relink Time-Out Bluetooth/ISM Network Activity Examples Default values When the scanner goes out of range, the scanner repeatedly attempts to connect to the base unit. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After one hour, the scanner powers off and batch mode data is lost. 3 - 24 Maximum Link Attempts set to 15 Other values at default settings When the scanner goes out of range, 15 attempts are made to link to the base unit. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After 15 cycles (8*15 =120), or about 2 minutes, the scanner stops trying to connect to the base, but retains any bar codes that may have been saved in batch mode. After one hour, the scanner powers off and batch mode data is lost. Auto Reconnect Mode set to 0 Maximum Link Attempts set to 15 Other values at default settings When the scanner goes out of range, no action is taken to relink. When the scanner’s button is pressed, 15 attempts are made to link to the base. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After 15 cycles (8*15 =120), or about 2 minutes, the scanner stops trying to connect to the base, but retains any bar codes that may have been saved in batch mode. After one hour, the scanner powers off and batch mode data is lost. Refer to Auto Reconnect Mode, page 3-23, to review other events that can start the relink process. Reset Scanner and Base After changing settings, you may need to reset your scanner and base. Scan the Reset Base bar code and wait for the scanner to unlink and relink to a base. Once that is done, scan the Reset Scanner bar code and wait for the base to unlink and relink to the scanner. Reset Scanner : * : RESE T _ . ³ Reset Base 3 - 25 3 - 26 4 Input/Output Settings Power Up Beeper The scanner can be programmed to beep when it’s powered up. Scan the Off bar code(s) if you don’t want a power up beep. Default = Power Up Beeper On - Scanner. Power Up Beeper Off Scanner * Power Up Beeper On Scanner Beep on BEL Character You may wish to force the scanner to beep upon a command sent from the host. If you scan the following Beep on BEL On bar code, the scanner will beep every time a BEL character is received from the host. Default = Beep on BEL Off. *Beep on BEL Off Beep on BEL On 4-1 Good Read and Error Indicators Beeper – Good Read The beeper may be programmed On or Off in response to a good read. Turning this option off, only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Default = Beeper Good Read On. Beeper - Good Read Off * Beeper - Good Read On Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High. Low Medium * High Off 4-2 Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read. Default = Medium. Low (1600 Hz) * Medium (2350 Hz) High (4200 Hz) Beeper - Transmit Order The beeper transmit order determines when the good read beep occurs. The scanner can be set to emit the good read beep either before or after data transmission. Default = Before Transmission. * Before Transmission After Transmission Beeper Pitch – Error The beeper pitch codes modify the pitch (frequency) of the sound the scanner emits when there is a bad read or error. Default = Razz. * Razz (100 Hz) Medium (2000 Hz) High (4200 Hz) 4-3 Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal. * Normal Beep Short Beep Number of Beeps – Good Read The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the beeper and LED in response to a good read. For example, if you program this option to have five beeps, there will be five beeps and five LED flashes in response to a good read. The beeps and LED flashes are in sync with one another. Note: The LEDs can also be programmed separately. See LED Settings on page 4-6. To change the number of beeps, scan the following bar code and then scan a digit (1-9) bar code and the Save bar code on the Programming Chart inside the back cover of this manual. Default = 1. Number of Good Read Beeps/LED Flashes Number of Beeps – Error The number of beeps and LED flashes emitted by the scanner for a bad read or error can be programmed from 1 - 9. For example, if you program this option to have five error beeps, there will be five error beeps and five LED flashes in response to an error. Note: The LEDs can also be programmed separately. See LED Settings on page 4-6. 4-4 To change the number of error beeps, scan the following bar code and then scan a digit (1-9) bar code and the Save bar code on the Programming Chart inside the back cover of this manual. Default = 1. Number of Error Beeps/LED Flashes 4-5 LED Indicators The green and red LEDs can be programmed to be On or Off and at different brightness levels to indicate various scanner states. Use the following bar codes to program the LED indicators. LED Settings Default = Red LED On with Laser, Green LED On with Good Scan. Red LED Off Green LED Off Red LED On with Good Scan * Green LED On with Good Scan * Red LED On with Laser Green LED On with Laser Red LED On when CodeGate Disabled Green LED On when CodeGate Disabled Red LED On when In-Stand Green LED On when In-Stand 4-6 Red LED On with CTS Green LED On with CTS Red LED On when Battery is Low Green LED On when Battery is Low 4-7 LED Brightness Default = Red High, Green High. Red Off Green Off Red Low Green Low Red Medium Green Medium * Red High * Green High In-Stand and Out-Of-Stand Settings The following settings program the scanner’s behavior when it is either in the stand, or out of the stand (hand-held). Caution: When working with In-Stand and Out-of-Stand settings, enable the settings you want before disabling those you do not want to use. If you disable settings first, you may program the scanner so it is unable to read bar codes. if this happens, power cycle the scanner and scan the defaults bar code on page 1-10. 4-8 In-Stand and Out-of-Stand Defaults If you want the In-Stand or Out-of-Stand default settings restored to your scanner, scan the appropriate Defaults bar code below. They reset the scanner to the custom default settings (see Setting Custom Defaults on page 1-9). If there are no custom defaults, it will reset the scanner to the factory default settings. Any settings that have not been specified through the custom defaults will be defaulted to the factory default settings. In-Stand Defaults Out-of-Stand Defaults Presentation Modes When the scanner is in the stand, by default, bar codes are automatically read when they are detected in the scanner’s field of view. When the scanner is out of the stand, by default you must push the button on top of the scanner to read a bar code. Use the following commands to adjust how the scanner behaves when it is out of the stand. Note: If you are using a cordless charge base in Presentation Mode, the battery will not charge unless the power supply is plugged into the base’s auxiliary power port. Presentation Mode Out-of-Stand: When the scanner is not in the stand, it automatically detects bar codes, then scans and transmits the data. The laser turns off afterward. (If you are accustomed to a Voyager 9520, this setting is the same as the 9520’s default.) Presentation Mode with CodeGate® Out-of-Stand: When the scanner is not in the stand, it automatically detects bar codes and decodes them. However, the data is not transmitted until you press the button. The laser remains on briefly after the transmission. (If you are accustomed to a Voyager 9540, this setting is the same as the 9540’s default.) Presentation Mode Out-of-Stand Presentation Mode with CodeGate Out-of-Stand 4-9 Manual Activation Mode In Manual Activation Mode, you must press the button to scan a bar code. The scanner scans until a bar code is read, or until the button is released. Default = Manual Activation Mode On In-Stand, Manual Activation On Outof-Stand. Manual Activation Mode Off In-Stand * Manual Activation Mode On In-Stand Manual Activation Mode Off Out-of-Stand * Manual Activation Mode On Out-of-Stand End Manual Activation After Good Read After a bar code is successfully read, the laser can be programmed either to remain on and scanning, or to turn off. When End Manual Activation After Good Read is enabled, the laser turns off and stops scanning after a good read. If you scan Do Not End Manual Activation After Good Read, the laser remains on after a good read, but the button must be pressed to scan the next bar code. Default = End Manual Activation After Good Read. Do Not End Manual Activation After Good Read In-Stand * End Manual Activation After Good Read In-Stand Do Not End Manual Activation After Good Read Out-of-Stand * End Manual Activation After Good Read Out-of-Stand 4 - 10 Manual Activation Laser Timeout - Button Settings You can set a timeout for the length of time the laser remains on and attempting to decode bar codes when the button is held down, and after it is released. Set the length (in milliseconds) for a timeout by scanning one of the following bar codes, then setting the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = Button Hold In-Stand 5000 ms, Button Hold Out-of-Stand 5000 ms, Button Release In or Out-of-Stand 0. Laser Timeout - Button Hold In-Stand Laser Timeout - Button Release In-Stand Laser Timeout - Button Hold Out-of-Stand Laser Timeout - Button Release Out-of-Stand 4 - 11 CodeGate® When CodeGate is On, the button is used to allow decoded data to be transmitted to the host system. The scanner remains on, scanning and decoding bar codes, but the bar code data is not transmitted until the button is pressed. When CodeGate is Off, bar code data is transmitted when it is decoded. Default = CodeGate Off in-Stand, CodeGate On Out-ofStand. * CodeGate Off In-Stand CodeGate On In-Stand CodeGate Off Out-of-Stand * CodeGate On Out-of-Stand Object Detection Mode Object Detection Mode uses an LED to detect when an object is in the scanner’s field of view. When an object is detected, the laser turns on and the scanner attempts to scan the bar code. Default = Object Detection Mode On In-Stand. Object Detection Mode Off In-Stand * Object Detection Mode On In-Stand * Object Detection Mode Off Out-of-Stand Object Detection Mode On Out-of-Stand 4 - 12 End Object Detection After Good Read After a bar code is successfully detected and read from the scanner, the laser can be programmed either to remain on and scanning, or to turn off. When End Object Detection After Good Read is enabled, the laser turns off and stops scanning after a good read. If you scan Do Not End Object Detection After Good Read, the laser remains on after a good read. Default = End Object Detection After Good Read. Do Not End Object Detection After Good Read In-Stand * End Object Detection After Good Read In-Stand Do Not End Object Detection After Good Read Out-of-Stand * End Object Detection After Good Read Out-of-Stand Object Detection Laser Timeout You can set a timeout for the length of time the laser remains on and attempting to decode bar codes after an object is detected. Set the length (in milliseconds) for a timeout by scanning the following bar code, then setting the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 5000 ms. Object Detection Laser Timeout In-Stand Object Detection Laser Timeout Out-of-Stand 4 - 13 Object Detection Distance When the scanner is in the stand and you are using Object Detection Mode, you can set the distance range for detecting objects. Short sets the scanner to detect objects approximately 5 inches (12.7cm) away from the nose. Long sets it to detect objects approximately 10 inches (25.4cm) away. Default = Short In-Stand, Long Out-of-Stand. * Short In-Stand Long In-Stand Short Out-of-Stand * Long Out-of-Stand Character Activation Mode You may use a character sent from the host to trigger the scanner to begin scanning. When the activation character is received, the scanner continues scanning until either the Character Activation Laser Timeout (page 4-15), the deactivation character is received (see Deactivation Character on page 4-16), or a bar code is transmitted. Scan the following On bar code to use character activation, then use Activation Character (following) to select the character you will send from the host to start scanning. Default = Off. * Off On Activation Character This sets the character used to trigger scanning when using Character Activation Mode. On the ASCII Conversion Chart (Code Page 1252), page A-4, find the hex value that represents the character you want to use to 4 - 14 trigger scanning. Scan the following bar code, then use the Programming Chart to read the alphanumeric combination that represents that ASCII character. Scan Save to finish. Activation Character End Character Activation After Good Read After a bar code is successfully detected and read from the scanner, the laser can be programmed either to remain on and scanning, or to turn off. When End Character Activation After Good Read is enabled, the laser turns off and stops scanning after a good read. If you scan Do Not End Character Activation After Good Read, the laser remains on after a good read. Default = End Character Activation After Good Read. Do Not End Character Activation After Good Read * End Character Activation After Good Read Character Activation Laser Timeout You can set a timeout for the length of time the laser remains on and attempting to decode bar codes when using Character Activation Mode. Set the length (in milliseconds) for a timeout by scanning the following bar code, then setting the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 5000 ms. Character Activation Laser Timeout 4 - 15 Character Deactivation Mode If you have sent a character from the host to trigger the scanner to begin scanning, you can also send a deactivation character to stop scanning. Scan the following On bar code to use character deactivation, then use Deactivation Character (following) to select the character you will send from the host to terminate scanning. Default = Off. * Off On Deactivation Character This sets the character used to terminate scanning when using Character Deactivation Mode. On the ASCII Conversion Chart (Code Page 1252), page A-4, find the hex value that represents the character you want to use to terminate scanning. Scan the following bar code, then use the Programming Chart to read the alphanumeric combination that represents that ASCII character. Scan Save to finish. Deactivation Character 4 - 16 Reread Delay This sets the time period before the scanner can read the same bar code a second time. Setting a reread delay protects against accidental rereads of the same bar code. Longer delays are effective in minimizing accidental rereads. Use shorter delays in applications where repetitive bar code scanning is required. Default = Medium. Short (500 ms) * Medium (750 ms) Long (1000 ms) Extra Long (2000 ms) User-Specified Reread Delay If you want to set your own length for the reread delay, scan the following bar code, then set the delay (from 0-30,000 milliseconds) by scanning digits from the Programming Chart, then scanning Save. User-Specified Reread Delay Output Sequence Overview Require Output Sequence When turned off, the bar code data will be output to the host as the scanner decodes it. When turned on, all output data must conform to an edited sequence or the scanner will not transmit the output data to the host device. See Require Output Sequence on page 4-21 for further information. 4 - 17 Output Sequence Editor This programming selection allows you to program the scanner to output data (when scanning more than one symbol) in whatever order your application requires, regardless of the order in which the bar codes are scanned. Reading the Default Sequence symbol programs the scanner to the following Universal values. These are the defaults. Be certain you want to delete or clear all formats before you read the Default Sequence symbol. Note: If CodeGate is enabled, you must hold the button down while reading each bar code in a sequence. Note: To make Output Sequence Editor selections, you’ll need to know the code I.D., code length, and character match(es) your application requires. Use the Alphanumeric symbols on the Programming Chart to read these options. To Add an Output Sequence 1. Scan the Enter Sequence symbol (see Require Output Sequence, page 4-21). 2. Code I.D. On the Symbology Chart on page A-1, find the symbology to which you want to apply the output sequence format. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart (inside back cover). 3. Length Specify what length (up to 9999 characters) of data output will be acceptable for this symbology. Scan the four digit data length from the Programming Chart. (Note: 50 characters is entered as 0050. 9999 is a universal number, indicating all lengths.) When calculating the length, you must count any programmed prefixes, suffixes, or formatted characters as part of the length (unless using 9999). 4. Character Match Sequences On the ASCII Conversion Chart (Code Page 1252), page A-4, find the Hex value that represents the character(s) you want to match. Use the Programming Chart to read the alphanumeric combination that represents the ASCII characters. (99 is the Universal number, indicating all characters.) 5. End Output Sequence Editor Scan F F to enter an Output Sequence for an additional symbology, or Save to save your entries. Other Programming Selections • Discard This exits without saving any Output Sequence changes. 4 - 18 Output Sequence Example In this example, you are scanning Code 93, Code 128, and Code 39 bar codes, but you want the scanner to output Code 39 1st, Code 128 2nd, and Code 93 3rd, as shown below. Note: Code 93 must be enabled to use this example. A - Code 39 B - Code 128 C - Code 93 You would set up the sequence editor with the following command line: SEQBLK62999941FF6A999942FF69999943FF The breakdown of the command line follows: SEQBLKsequence editor start command 62 code identifier for Code 39 9999 code length that must match for Code 39, 9999 = all lengths 41 start character match for Code 39, 41h = “A” FF termination string for first code 6A code identifier for Code 128 9999 code length that must match for Code 128, 9999 = all lengths 42 start character match for Code 128, 42h = “B” FF termination string for second code 69 code identifier for Code 93 9999 code length that must match for Code 93, 9999 = all lengths 43 start character match for Code 93, 43h = “C” FF termination string for third code To program the previous example using specific lengths, you would have to count any programmed prefixes, suffixes, or formatted characters as part of the length. If you use the example on page 4-19, but assume a suffix and specific code lengths, you would use the following command line: SEQBLK62001241FF6A001342FF69001243FF The breakdown of the command line follows: 4 - 19 SEQBLKsequence editor start command 62 code identifier for Code 39 0012 A - Code 39 sample length (11) plus CR suffix (1) = 12 41 start character match for Code 39, 41h = “A” FF termination string for first code 6A code identifier for Code 128 0013 B - Code 128 sample length (12) plus CR suffix (1) = 13 42 start character match for Code 128, 42h = “B” FF termination string for second code 69 code identifier for Code 93 0012 C - Code 93 sample length (11) plus CR suffix (1) = 12 43 start character match for Code 93, 43h = “C” FF termination string for third code Output Sequence Editor Enter Sequence Default Sequence Sequence Timeout You may wish to set the maximum time between bar code scans in an output sequence. If that maximum time is not met, the output sequence operation is terminated. Set the length (in milliseconds) for a timeout by scanning the following bar code, then setting the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 5000 msec. Sequence Timeout 4 - 20 Sequence Match Beeper By default, the scanner beeps when a sequence match is found. If you want the scanner to remain silent, scan the following Sequence Match Beeper Off bar code. Default = Sequence Match Beeper On. Sequence Match Beeper Off * Sequence Match Beeper On Partial Sequence If an output sequence operation is terminated before all your output sequence criteria are met, the bar code data acquired to that point is a “partial sequence.” Scan Discard Partial Sequence to discard partial sequences when the output sequence operation is terminated before completion. Scan Transmit Partial Sequence to transmit partial sequences. (Any fields in the sequence where no data match occurred will be skipped in the output.) If you have programmed a Sequence Timeout (page 4-20) and the timeout is reached, the partial sequence is transmitted. Default = Discard Partial Sequence. Transmit Partial Sequence * Discard Partial Sequence Require Output Sequence When an output sequence is Required, all output data must conform to an edited sequence or the scanner will not transmit the output data to the host device. When it’s On/Not Required, the scanner will attempt to get the output data to conform to an edited sequence but, if it cannot, the scanner transmits all output data to the host device as is. 4 - 21 When the output sequence is Off, the bar code data is output to the host as the scanner decodes it. Default = Off. Required On/Not Required *Off No Read With No Read turned On, the scanner notifies you if a code cannot be read. If using an EZConfig-Scanning Tool Scan Data Window (see page 9-2), an “NR” appears when a code cannot be read. If No Read is turned Off, the “NR” will not appear. Default = Off. On * Off If you want a different notation than “NR,” for example, “Error,” or “Bad Code,” you can edit the output message (see Data Formatting beginning on page 6-1). The hex code for the No Read symbol is 9C. 4 - 22 5 Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string. Prefix and Suffix characters are data characters that can be sent before and after scanned data. You can specify if they should be sent with all symbologies, or only with specific symbologies. The following illustration shows the breakdown of a message string: Prefix Scanned Data 1-11 variable length alpha numeric & control characters Suffix 1-11 alpha numeric & control characters Points to Keep In Mind • It is not necessary to build a message string. The selections in this chapter are only used if you wish to alter the default settings. Default prefix = None. Default suffix is dependent on interface. • A prefix or suffix may be added or cleared from one symbology or all symbologies. • You can add any prefix or suffix from the ASCII Conversion Chart (Code Page 1252), beginning on page A-4, plus Code I.D. and AIM I.D. • You can string together several entries for several symbologies at one time. • Enter prefixes and suffixes in the order in which you want them to appear on the output. • When setting up for specific symbologies (as opposed to all symbologies), the specific symbology ID value counts as an added prefix or suffix character. • The maximum size of a prefix or suffix configuration is 32 characters, which includes header information. To Add a Prefix or Suffix: Step 1. Scan the Add Prefix or Add Suffix symbol (page 5-3). Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Symbology Chart, beginning on page A-1) for the 5-1 symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”. Step 3. Scan the 2 hex digits from the Programming Chart inside the back cover of this manual or scan 9, 9 for all symbologies. Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page 1252) on page A-4, for the prefix or suffix you wish to enter. Step 5. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual. Step 6. Repeat Steps 4 and 5 for every prefix or suffix character. Step 7. To add the Code I.D., scan 5, C, 8, 0. To add AIM I.D., scan 5, C, 8, 1. To add a backslash (\), scan 5, C, 5, C. Note: To add a backslash (\) as in Step 7, you must scan 5C twice – once to create the leading backslash and then to create the backslash itself. Step 8. Scan Save to exit and save, or scan Discard to exit without saving. Repeat Steps 1-6 to add a prefix or suffix for another symbology. Example: Add a Suffix to a specific symbology To send a CR (carriage return)Suffix for U.P.C. only: Step 1. Scan Add Suffix. Step 2. Determine the 2 digit hex value from the Symbology Chart (included in the Symbology Chart, beginning on page A-1) for U.P.C. Step 3. Scan 6, 3 from the Programming Chart inside the back cover of this manual. Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page 1252) on page A-4, for the CR (carriage return). Step 5. Scan 0, D from the Programming Chart inside the back cover of this manual. Step 6. Scan Save, or scan Discard to exit without saving. To Clear One or All Prefixes or Suffixes You can clear a single prefix or suffix, or clear all prefixes/suffixes for a symbology. If you have been entering prefixes and suffixes for single symbologies, you can use Clear One Prefix (Suffix) to delete a specific character from a symbology. When you Clear All Prefixes (Suffixes), all the prefixes or suffixes for a symbology are deleted. 5-2 Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Symbology Chart, beginning on page A-1) for the symbology from which you want to clear the prefix or suffix. Step 3. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual or scan 9, 9 for all symbologies. Your change is automatically saved. To Add a Carriage Return Suffix to All Symbologies Scan the following bar code if you wish to add a carriage return suffix to all symbologies at once. This action first clears all current suffixes, then programs a carriage return suffix for all symbologies. Add CR Suffix All Symbologies Prefix Selections Add Prefix Clear One Prefix Clear All Prefixes 5-3 Suffix Selections Add Suffix Clear One Suffix Clear All Suffixes Transmit Alternate Extended ASCII Characters You may need to emulate special keyboard functions, such as up or down arrows, Alt/Make or Alt/Break commands, that are not supported in the Extended ASCII Character table. Refer to Alternate Extended ASCII Characters (page 5-5) for a range of keyboard function keys and corresponding decimal and hex characters. If you scan the Transmit Alternate Extended ASCII code, any hex entries in a prefix or suffix will result in the corresponding Keyboard Function output. Example: Transmit Alternate Extended ASCII is enabled, and you scan Add Suffix, then scan 9 9 8 9. All symbologies (99) would have a suffix of a Page Down (hex 89) added to them. When Transmit Normal Extended ASCII is selected, the normal extended ASCII character is transmitted (see ASCII Conversion Chart (Code Page 1252) on page A-4). Example: Transmit Normal Extended ASCII is enabled, and you scan Add Suffix, then scan 9 9 8 9. All symbologies (99) would have a suffix of a ‰ character added to them. Default = Transmit Alternate Extended ASCII. * Transmit Alternate Extended ASCII Transmit Normal Extended ASCII 5-4 Alternate Extended ASCII Characters DEC HEX Keyboard Function 128 80 129 81 130 82 up arrow ↑ down arrow ↓ right arrow → DEC HEX Keyboard Function 152 98 F9 153 99 F10 154 9A F11 131 83 left arrow ← 155 9B F12 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 Insert Delete Home End Page Up Page Down Right ALT Right CTRL Reserved Reserved Numeric Keypad Enter Numeric Keypad / F1 F2 F3 F4 F5 F6 F7 F8 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 Numeric Keypad + Numeric Keypad Numeric Keypad * Caps Lock Num Lock Left Alt Left Ctrl Left Shift Right Shift Print Screen Tab Shift Tab Enter Esc Alt Make Alt Break Control Make Control Break Alt Sequence with 1 Character Ctrl Sequence with 1 Character 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF 5-5 Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in Supported Interface Keys starting on page 8-2. When the scanner is in keyboard wedge mode, the scan code is converted to a key code before it is transmitted. Default = Enable. * Enable Disable Communication Check Character To enhance security, you can specify the transmission type of a check character; either LRC where the calculation starts on the first transmitted character, LRC where the calculation starts on the second transmitted character, or CRC. Note: This option adds a check character to the bar code data for all symbologies. If you need to enable or disable check characters for individual symbologies, see Symbologies beginning on page 7-1. Scan the following bar code to set the communication check character type. Default = None. * None LRC Starts on 1st Character LRC Starts on 2nd Character CRC 5-6 Intercharacter, Interfunction, and Intermessage Delays Some terminals drop information (characters) if data comes through too quickly. Intercharacter, interfunction, and intermessage delays slow the transmission of data, increasing data integrity. Intercharacter Delay An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each character of scanned data. Scan the following Intercharacter Delay bar code, then scan the number of 5ms delays, and the Save bar code using the Programming Chart inside the back cover of this manual. Prefix Scanned Data Suffix Intercharacter Delay Intercharacter Delay To remove this delay, scan the Intercharacter Delay bar code, then set the number of delays to 0. Scan the Save bar code using the Programming Chart inside the back cover of this manual. Note: Intercharacter delays are not supported in USB serial emulation. User Specified Intercharacter Delay An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed after the transmission of a particular character of scanned data. Scan the following Delay Length bar code, then scan the number of 5ms delays, and the Save bar code using the Programming Chart inside the back cover of this manual. 5-7 Next, scan the Character to Trigger Delay bar code, then the 2-digit hex value for the ASCII character that will trigger the delay ASCII Conversion Chart (Code Page 1252) on page A-4. Delay Length Character to Trigger Delay To remove this delay, scan the Delay Length bar code, and set the number of delays to 0. Scan the Save bar code using the Programming Chart inside the back cover of this manual. Interfunction Delay An interfunction delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each segment of the message string. Scan the following Interfunction Delay bar code, then scan the number of 5ms delays, and the Save bar code using the Programming Chart inside the back cover of this manual. Prefix STX Scanned Data HT 2 3 4 5 Suffix CR LF Interfunction Delays Interfunction Delay To remove this delay, scan the Interfunction Delay bar code, then set the number of delays to 0. Scan the Save bar code using the Programming Chart inside the back cover of this manual. 5-8 Intermessage Delay An intermessage delay of up to 5000 milliseconds (in 5ms increments) may be placed between each scan transmission. Scan the following Intermessage Delay bar code, then scan the number of 5ms delays, and the Save bar code using the Programming Chart inside the back cover of this manual. 1st Scan Transmission 2nd Scan Transmission Intermessage Delay Intermessage Delay To remove this delay, scan the Intermessage Delay bar code, then set the number of delays to 0. Scan the Save bar code using the Programming Chart inside the back cover of this manual. 5-9 5 - 10 6 Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output. Default Data Format setting = None. Normally, when you scan a bar code, it gets outputted automatically; however when you create a format, you must use a “send” command (see Send Commands on page 6-4) within the format program to output data. Multiple formats may be programmed into the scanner. They are stacked in the order in which they are entered. However, the following list presents the order in which formats are applied: 1. 2. 3. 4. 5. 6. 7. 8. Specific Terminal ID, Actual Code ID, Actual Length Specific Terminal ID, Actual Code ID, Universal Length Specific Terminal ID, Universal Code ID, Actual Length Specific Terminal ID, Universal Code ID, Universal Length Universal Terminal ID, Actual Code ID, Actual Length Universal Terminal ID, Actual Code ID, Universal Length Universal Terminal ID, Universal Code ID, Actual Length Universal Terminal ID, Universal Code ID, Universal Length The maximum size of a data format configuration is 256 bytes, which includes header information. No format can contain more than 50 bytes. If you have changed data format settings, and wish to clear all formats and return to the factory defaults, scan the following Default Data Format code. * Default Data Format To Add a Data Format Step 1. Scan the Enter Data Format symbol (page 6-2). Step 2. Select Primary/Alternate Format Determine if this will be your primary data format, or one of 3 alternate formats. This allows you to save a total of 4 different data formats. To program your primary format, scan 0 using the Programming Chart inside the back cover of this manual. If you are programming an alternate format, scan 1, 2, or 3, depending on which alternate format 6-1 you are programming. (See Primary/Alternate Data Formats on page 6-10 for further information.) Step 3. Terminal Type Refer to Terminal ID Table (page 6-4) and locate the Terminal ID number for your PC. Scan three numeric bar codes on the Programming Chart to program the scanner for your terminal ID (you must enter 3 digits). For example, scan 0 0 3 for an AT wedge. Note: The wildcard for all terminal types is 099. Step 4. Code I.D. In the Symbology Chart, beginning on page A-1, find the symbology to which you want to apply the data format. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart inside the back cover of this manual. Step 5. Length Specify what length (up to 9999 characters) of data will be acceptable for this symbology. Scan the four digit data length from the Programming Chart inside the back cover of this manual. (Note: 50 characters is entered as 0050. 9999 is a universal number, indicating all lengths.) Step 6. Editor Commands Refer to (page 6-4). Scan the symbols that represent the command you want to enter. 94 alphanumeric characters may be entered for each symbology data format. Step 7. Scan Save to save your data format, or Discard to exit without saving your changes. Enter Data Format Save Discard 6-2 Other Programming Selections Clear One Data Format This deletes one data format for one symbology. If you are clearing the primary format, scan 0 from the Programming Chart inside the back cover of this manual. If you are clearing an alternate format, scan 1, 2, or 3, depending on the format you are clearing. Scan the Terminal Type and Code I.D. (see Symbology Chart on page A-1), and the bar code data length for the specific data format that you want to delete. All other formats remain unaffected. Clear all Data Formats This clears all data formats. Save to exit and save your data format changes. Discard to exit without saving any data format changes. Clear One Data Format Clear All Data Formats Save Discard 6-3 Terminal ID Table Terminal Model(s) IBM PC/AT and compatibles PS2 Keyboard USB SurePOS Handheld Scanner USB SurePOS Tabletop Scanner True TTL RS232 RS485 USB Serial PC Keyboard Mac Keyboard Japanese Keyboard (PC) HID POS Terminal ID 003 002 128 129 000 000 051 130 124 125 134 131 Data Format Editor Commands Send Commands Send all characters F1 Include in the output message all of the characters from the input message, starting from current cursor position, followed by an insert character. Syntax = F1xx where xx stands for the insert character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for decimal, hex and character codes. Send a number of characters F2 Include in the output message a number of characters followed by an insert character. Start from the current cursor position and continue for “nn” characters or through the last character in the input message, followed by character “xx.” Syntax = F2nnxx where nn stands for the numeric value (00-99) for the number of characters, and xx stands for the insert character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for decimal, hex and character codes. 6-4 Send all characters up to a particular character F3 Include in the output message all characters from the input message, starting with the character at the current cursor position and continuing to, but not including, the search character “ss,” followed by an insert character. The cursor is moved forward to the “ss” character. Syntax = F3ssxx where ss stands for the search character’s hex value for its ASCII code, and xx stands for the insert character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for decimal, hex and character codes. Send all but the last characters E9 Include in the output message all but the last “nn” characters, starting from the current cursor position. The cursor is moved forward to one position past the last input message character included. Syntax = E9nn where nn stands for the numeric value (00-99) for the number of characters that will not be sent at the end of the message. Insert a character multiple times F4 Send “xx” character “nn” times in the output message, leaving the cursor in the current position. Syntax = F4xxnn where xx stands for the insert character’s hex value for its ASCII code, and nn is the numeric value (00-99) for the number of times it should be sent. Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for decimal, hex and character codes. Insert symbology name B3 Insert the name of the bar code’s symbology in the output message, without moving the cursor. Only symbologies with a Honeywell ID are included (see Symbology Chart on page A-1). Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for decimal, hex and character codes. Insert bar code length B4 Insert the bar code’s length in the output message, without moving the cursor. The length is expressed as a numeric string and does not include leading zeroes. Move Commands Move the cursor forward a number of characters F5 Move the cursor ahead “nn” characters from current cursor position. Syntax = F5nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved ahead. Move the cursor backward a number of characters F6 Move the cursor back “nn” characters from current cursor position. Syntax = F6nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved back. 6-5 Move the cursor to the beginning F7 Move the cursor to the first character in the input message. Syntax = F7. Move the cursor to the end EA Move the cursor to the last character in the input message. Syntax = EA. Search Commands Search forward for a character F8 Search the input message forward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. Syntax = F8xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for decimal, hex and character codes. Search backward for a character F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. Syntax = F9xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for decimal, hex and character codes. Search forward for a string B0 Search forward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B0nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B0000454657374 will search forward for the first occurrence of the 4 character string “Test.” Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for decimal, hex and character codes. Search backward for a string B1 Search backward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B1nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B1000454657374 will search backward for the first occurrence of the 4 character string “Test.” Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for decimal, hex and character codes. 6-6 Search forward for a non-matching character E6 Search the input message forward for the first non-“xx” character from the current cursor position, leaving the cursor pointing to the non-“xx” character. Syntax = E6xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for decimal, hex and character codes. Search backward for a non-matching character E7 Search the input message backward for the first non-“xx” character from the current cursor position, leaving the cursor pointing to the non“xx” character. Syntax = E7xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for decimal, hex and character codes. Miscellaneous Commands Suppress characters FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is advanced by other commands. When the FC command is encountered, the suppress function is terminated. The cursor is not moved by the FB command. Syntax = FBnnxxyy . .zz where nn is a count of the number of suppressed characters in the list, and xxyy .. zz is the list of characters to be suppressed. Stop suppressing characters FC Disables suppress filter and clear all suppressed characters. Syntax = FC. Replace characters E4 Replaces up to 15 characters in the output message, without moving the cursor. Replacement continues until the E5 command is encountered. Syntax = E4nnxx1xx2yy1yy2...zz1zz2 where nn is the total count of the number of characters in the list (characters to be replaced plus replacement characters); xx1 defines characters to be replaced and xx2 defines replacement characters, continuing through zz1 and zz2. Stop replacing characters E5 Terminates character replacement. Syntax = E5. 6-7 Compare characters FE Compare the character in the current cursor position to the character “xx.” If characters are equal, move the cursor forward one position. Syntax = FExx where xx stands for the comparison character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for decimal, hex and character codes. Compare string B2 Compare the string in the input message to the string “s.” If the strings are equal, move the cursor forward past the end of the string. Syntax = B2nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B2000454657374 will compare the string at the current cursor position with the 4 character string “Test.” Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for decimal, hex and character codes. Check for a number EC Check to make sure there is an ASCII number at the current cursor position. The format is aborted if the character is not numeric. Check for non-numeric character ED Check to make sure there is a non-numeric ASCII character at the current cursor position. The format is aborted if the character is numeric. Insert a delay EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position. Syntax = EFnnnn where nnnn stands for the delay in 5ms increments, up to 9999. This command can only be used with keyboard wedge interfaces. Data Formatter When Data Formatter is turned Off, the bar code data is output to the host as read, including prefixes and suffixes. Data Formatter Off You may wish to require the data to conform to a data format you have created and saved. The following settings can be applied to your data format: Data Formatter On, Not Required, Keep Prefix/Suffix Scanned data is modified according to your data format, and prefixes and suffixes are transmitted. 6-8 Data Formatter On, Not Required, Drop Prefix/Suffix Scanned data is modified according to your data format. If a data format is found for a particular symbol, those prefixes and suffixes are not transmitted. Data Format Required, Keep Prefix/Suffix Scanned data is modified according to your data format, and prefixes and suffixes are transmitted. Any data that does not match your data format requirements generates an error tone and the data in that bar code is not transmitted. If you wish to process this type of bar code without generating an error tone, see Data Format Non-Match Error Tone. Data Format Required, Drop Prefix/Suffix Scanned data is modified according to your data format. If a data format is found for a particular symbol, those prefixes and suffixes are not transmitted. Any data that does not match your data format requirements generates an error tone. If you wish to process this type of bar code without generating an error tone, see Data Format Non-Match Error Tone. Choose one of the following options. Default = Data Formatter On, Not Required, Keep Prefix/Suffix. * Data Formatter On, Not Required, Keep Prefix/Suffix Data Formatter On, Not Required, Drop Prefix/Suffix Data Format Required, Keep Prefix/Suffix Data Format Required, Drop Prefix/Suffix Data Format Non-Match Error Tone When a bar code is encountered that doesn’t match your required data format, the scanner normally generates an error tone. However, you may want to continue scanning bar codes without hearing the error tone. If you scan the Data Format Non-Match Error Tone Off bar code, data that doesn’t conform to your data format is not transmitted, and no error tone 6-9 will sound. If you wish to hear the error tone when a non-matching bar code is found, scan the Data Format Non-Match Error Tone On bar code. Default = Data Format Non-Match Error Tone On. * Data Format Non-Match Error Tone On Data Format Non-Match Error Tone Off Primary/Alternate Data Formats You can save up to four data formats, and switch between these formats. Your primary data format is saved under 0. Your other three formats are saved under 1, 2, and 3. To set your device to use one of these formats, scan one of the following bar codes. Primary Data Format Data Format 1 Data Format 2 Data Format 3 Single Scan Data Format Change You can also switch between data formats for a single scan. The next bar code is scanned using an alternate data format, then reverts to the format you have selected above (either Primary, 1, 2, or 3). 6 - 10 For example, you may have set your device to the data format you saved as Data Format 3. You can switch to Data Format 1 for a single button press by scanning the following Single Scan-Data Format 1 bar code. The next bar code that is scanned uses Data Format 1, then reverts back to Data Format 3. Single Scan-Primary Data Format Single Scan-Data Format 1 Single Scan-Data Format 2 Single Scan-Data Format 3 6 - 11 6 - 12 7 Symbologies This programming section contains the following menu selections. Refer to Chapter 10 for settings and defaults. • All Symbologies • GS1-128 • Airline Code 5 - see Straight 2 of 5 IATA (two-bar start/stop) • Interleaved 2 of 5 • China Post (Hong Kong 2 of 5) • ISBT 128 • Codabar • Matrix 2 of 5 • Code 11 • MSI • Code 128 • NEC 2 of 5 • Code 32 Pharmaceutical (PARAF) • Plessey Code • Code 39 • Postal Codes • Code 93 • Straight 2 of 5 IATA (two-bar start/ stop) • EAN/JAN-13 • Straight 2 of 5 Industrial (three-bar start/stop) • EAN/JAN-8 • Telepen • GS1 DataBar Expanded • Trioptic Code • GS1 DataBar Limited • UPC-A • GS1 DataBar Omnidirectional • UPC-A/EAN-13 with Extended Coupon Code • GS1 Emulation • UPC-E0 All Symbologies If you want to decode all the symbologies allowable for your scanner, scan the All Symbologies On code. If on the other hand, you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular symbology. All Symbologies On All Symbologies Off 7-1 Message Length Description You are able to set the valid reading length of some of the bar code symbologies. If the data length of the scanned bar code doesn’t match the valid reading length, the scanner will issue an error tone. You may wish to set the same value for minimum and maximum length to force the scanner to read fixed length bar code data. This helps reduce the chances of a misread. EXAMPLE: Decode only those bar codes with a count of 9-20 characters. Min. length = 09Max. length = 20 EXAMPLE: Decode only those bar codes with a count of 15 characters. Min. length = 15Max. length = 15 For a value other than the minimum and maximum message length defaults, scan the bar codes included in the explanation of the symbology, then scan the digit value of the message length and Save bar codes on the Programming Chart inside the back cover of this manual. The minimum and maximum lengths and the defaults are included with the respective symbologies. 7-2 Codabar Codabar On/Off * On Off Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar bar codes with Modulo 16, Modulo 7 CD, or CLSI check characters. Default = No Check Character. No Check Character indicates that the scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate and Transmit, the scanner will only read Codabar bar codes printed with a check character, and will transmit this character at the end of the scanned data. 7-3 When Check Character is set to Validate, but Don’t Transmit, the unit will only read Codabar bar codes printed with a check character, but will not transmit the check character with the scanned data. * No Check Character Validate Modulo 16, but Don’t Transmit Validate Modulo 16 and Transmit Validate Modulo 7 CD, but Don’t Transmit Validate Modulo 7 CD and Transmit Validate CLSI, but Don’t Transmit Validate CLSI and Transmit Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concatenated into one with the “D” characters omitted. A 1 2 3 4 D 7-4 D 5 6 7 8 A Select Require to prevent the scanner from decoding a single “D” Codabar symbol without its companion. This selection has no effect on Codabar symbols without Stop/Start D characters. On * Off Require Concatenation Timeout When searching for bar codes during concatenation, you may wish to set a delay used to find the next bar code. Set the length (in milliseconds) for this delay by scanning the following bar code, then setting the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 750. Concatenation Timeout Codabar Redundancy If you are encountering errors when reading Codabar bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the following Codabar Redundancy bar code, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. Codabar Redundancy 7-5 Codabar Message Length Scan the following bar codes to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length 7-6 Code 39 < Default All Code 39 Settings > Code 39 On/Off * On Off Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Code 39 Check Character No Check Character indicates that the scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate, but Don’t Transmit, the unit only reads Code 39 bar codes printed with a check character, but will not transmit the check character with the scanned data. 7-7 When Check Character is set to Validate and Transmit, the scanner only reads Code 39 bar codes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Character. * No Check Character Validate, but Don’t Transmit Validate and Transmit Code 39 Redundancy If you are encountering errors when reading Code 39 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the Code 39 Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. Code 39 Redundancy Code 39 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length 7-8 Code 32 Pharmaceutical (PARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian pharmacies. This symbology is also known as PARAF. On * Off Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = Off. NUL %U DLE $P SP SPACE 0 %V ‘ %W p +P SOH $A DC1 $Q /A +A +Q STX $B DC2 $R “ /B +B +R ETX $C DC3 $S /C +C +S EOT $D DC4 $T /D +D +T ENQ $E NAK $U /E +E +U ACK $F SYN $V /F +F +V BEL $G ETB $W ‘ /G +G +W BS $H CAN $X /H +H +X HT $I EM $Y /I +I +Y LF $J SUB $Z /J /Z +J +Z VT $K ESC %A /K %F %K +K %P FF $L FS %B /L %G L %L +L %Q CR $M GS %C %H %M m +M %R SO $N RS %D %I %N +N %S SI $O US %E /O %J %O o +O DEL %T 7-9 Character pairs /M and /N decode as a minus sign and period respectively. Character pairs /P through /Y decode as 0 through 9. Full ASCII On * Full ASCII Off 7 - 10 Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 On/Off * On Off Follett Formatting * Off On NULL Characters Interleaved 2 of 5 requires an even number of characters. When an odd number of characters is present, it is due to NULL characters embedded in the bar code. Scan the On bar code below to decode this type of Interleaved 2 of 5 bar code. Default = Off. * Off On 7 - 11 Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads Interleaved 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data. When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit Interleaved 2 of 5 Redundancy If you are encountering errors when reading Interleaved 2 of 5 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the Interleaved 2 of 5 Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. Interleaved 2 of 5 Redundancy 7 - 12 Interleaved 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 6, Maximum Default = 80. Minimum Message Length Maximum Message Length NEC 2 of 5 < Default All NEC 2 of 5 Settings > NEC 2 of 5 On/Off On * Off Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data. 7 - 13 When Check Digit is set to Validate and Transmit, the scanner only reads NEC 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit NEC 2 of 5 Redundancy If you are encountering errors when reading NEC 2 of 5 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the NEC 2 of 5 Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. NEC 2 of 5 Redundancy NEC 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length 7 - 14 Code 93 < Default All Code 93 Settings > Code 93 On/Off * On Off Code 93 Redundancy If you are encountering errors when reading Code 93 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the Code 93 Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. Code 93 Redundancy 7 - 15 Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length Straight 2 of 5 Industrial (three-bar start/stop) Straight 2 of 5 Industrial On/Off On * Off Straight 2 of 5 Industrial Redundancy If you are encountering errors when reading Straight 2 of 5 Industrial bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the Straight 2 of 5 Industrial Redundancy bar code below, then 7 - 16 scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. Straight 2 of 5 Industrial Redundancy Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 3-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length 7 - 17 Straight 2 of 5 IATA (two-bar start/stop) Note: This symbology is also known as Airline Code 5. Straight 2 of 5 IATA On/Off On * Off Straight 2 of 5 IATA Redundancy If you are encountering errors when reading Straight 2 of 5 IATA bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the Straight 2 of 5 IATA Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. Straight 2 of 5 IATA Redundancy 7 - 18 Straight 2 of 5 IATA Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 13, Maximum Default = 15. Minimum Message Length Maximum Message Length Matrix 2 of 5 Matrix 2 of 5 On/Off On * Off Matrix 2 of 5 Check Character No Check Character indicates that the scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate, but Don’t Transmit, the unit only reads Matrix 2 of 5 bar codes printed with a check character, but will not transmit the check character with the scanned data. 7 - 19 When Check Character is set to Validate and Transmit, the scanner only reads Matrix 2 of 5 bar codes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Character. * No Check Character Validate, but Don’t Transmit Validate and Transmit Matrix 2 of 5 Redundancy If you are encountering errors when reading Matrix 2 of 5 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the Matrix 2 of 5 Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. Matrix 2 of 5 Redundancy Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length 7 - 20 Code 11 Code 11 On/Off On * Off Check Digits Required These options set whether 1 or 2 check digits are required with Code 11 bar codes. Auto Select Check Digits determines the number of check digits based on the length of the bar code. If the bar code is 10 digits or more, 2 check digits are required. If it is 9 digits or less, 1 check digit is required. The check digit data is only transmitted if you program that feature (see Check Digit Validation on page 7-22). Default = Two Check Digits Required. One Check Digit Required * Two Check Digits Required Auto Select Check Digits Required 7 - 21 Check Digit Validation When Check Character is set to Validate and Transmit, the scanner will only read Code 11 bar codes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data. Validate and Transmit One Check Digit Validate and Transmit Two Check Digits Validate and Transmit Auto Select Check Digits Code 11 Redundancy If you are encountering errors when reading Code 11 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the Code 11 Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. Code 11 Redundancy 7 - 22 Code 11 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length 7 - 23 Code 128 Code 128 On/Off * On Off 128 Group Separator Output If you wish to transmit the group separator characters “GS” (0x1D hex) with your Code 128 bar code output, scan the On bar code. When Off is scanned, the group separator is not output. Default =Off. On * Off Code 128 Redundancy If you are encountering errors when reading Code 128 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the Code 7 - 24 128 Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. Code 128 Redundancy Code 128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length ISBT 128 ISBT is a variation of Code 128 that supports concatenation of neighboring symbols on a blood product label. Use the bar codes below to turn ISBT 128 concatenation on or off. Default =Off. On * Off 7 - 25 Concatenation Timeout When searching for bar codes during concatenation, you may wish to set a delay used to find the next bar code. Set the length (in milliseconds) for this delay by scanning the bar code below, then setting the timeout (from 165535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 750. Concatenation Timeout ISBT 128 Predefined Concatenation Sequences Note: You must enable Code 128 and ISBT 128 to use this feature. The following bar codes are used to select the pre-defined ISBT 128 Concatenation Sequence you wish to use. Once you have selected the concatenation sequence, use ISBT 128 Predefined Concatenation Sequences On/Off to enable this feature. Default = Donation ID Number (001) and ABO/RhD Blood Groups (002). * Donation ID Number (001) and ABO/RhD Blood Groups (002) Donation ID Number (001) and Donor ID Number (019) Donation ID Number (001) and Confidential Unit Exclusion Status Product Code (003) and Expiration Date (Form 1) Product Code (003) and Expiration Date (Form 2) Product Code (003) and Expiration Date (Form 3) Product Code (003) and Expiration Date (Form 4) 7 - 26 ISBT 128 Predefined Concatenation Sequences On/ Off The following selections allow you to enable or require the Predefined ISBT 128 Concatenation Sequences. If you scan Off, the predefined concatenation sequences are disabled. If you scan the Allow Predefined Sequence code, then the scanner will output only the data combination specified in the predefined concatenation sequence you selected. If you scan the Require Predefined Sequence code, the data combination specified in the predefined concatenation sequence you selected is required to transmit the data. No data is output unless the sequence is read. Default = Off. * Off Allow Predefined Sequence Require Predefined Sequence ISBT 128 User-Defined Concatenation Sequences Note: You must enable Code 128 and ISBT 128 to use this feature. The following bar codes are used to create a custom ISBT 128 Concatenation Sequence. Select the identifiers you want to transmit in the 1st and 2nd positions, both left and right. Refer to the ISBT 128 Standard Technical Specification for the list of data identifiers. Use the ASCII Conversion Chart (Code Page 1252), beginning on page A4, to find the characters needed for the identifier. Locate the hex value for each character and scan that 2 digit/character value from the Programming Chart inside the back cover of this manual. Example: You want to create a concatenation sequence that has the Donation Identification Number (001) as the left identifier, and Product Code (003) as the right identifier. The ISBT Index of Data Structures shows that for the Donation Identification Number, the first character is “=” and the second character can be from A-N; P-Z; 1-9. For this example, use “G.” The Product Code first character is “=” and the second character is “<.” 7 - 27 Step 1. Scan the 1st Left Identifier bar code, below. Step 2. Use the Programming Chart to scan 3, D (hex for “=”). Step 3. Scan Save. Step 4. Scan the 2nd Left Identifier bar code, below. Step 5. Use the Programming Chart to scan 4, 7 (hex for “G”). Step 6. Scan Save. Step 7. Scan the 1st Right Identifier bar code, below. Step 8. Use the Programming Chart to scan 3, D (hex for “=”). Step 9. Scan Save. Step 10. Scan the 2nd Right Identifier bar code, below. Step 11. Use the Programming Chart to scan 3, C (hex for “<”). Step 12. Scan Save. Once you have programmed the concatenation sequence, use ISBT 128 User-Defined Concatenation Sequences to enable this feature. Default = 0. 1st Left Identifier 2nd Left Identifier 1st Right Identifier 2nd Right Identifier ISBT 128 User-Defined Concatenation Sequences On/Off The following selections allow you to enable or require the User-Defined ISBT 128 Concatenation Sequences. If you scan Off, the User-Defined concatenation sequences are disabled. If you scan the Allow User-Defined Sequence code, then the scanner will output only the data combination specified in the User-Defined concatenation sequence you created. 7 - 28 If you scan the Require User-Defined Sequence code, the data combination specified in the User-Defined concatenation sequence is required to transmit the data. No data is output unless the sequence is read. Default = Off. * Off Allow User-Defined Sequence Require User-Defined Sequence Content Verification When the On bar code is scanned, the check character values are output along with the bar code data, thus allowing you to verify that the check character is in agreement with that calculated for the data stream. Default = Off. On * Off Transmit Identifiers You may disable the transmission of the ISBT Code 128 data identifiers by scanning Off. When this selection is Off, the first 2 data (ID) characters are removed from the data stream unless the ISBT code contains the Donation Identification Number identifiers. If the code contains the Donation Identifi- 7 - 29 cation Number identifiers, only the first ID character is removed from the Donation Identification Number. The second character is transmitted as normal data. Default = On. * On Off Flag Digit Conversion Type 3 flag digits are a part of the Donation Identification Number in an ISBT 128 bar code. If you select On, the flag data is converted into a single MOD (37, 2) character and transmitted with the bar code data. Scan Off if you do not want the flag digits transmitted. Default = Off. On * Off 7 - 30 GS1-128 GS1-128 On/Off * On Off GS1-128 Application Identifier Parsing This allows a single GS1-128 bar code to be broken into multiple transmissions based on the presence of application identifiers (AI) embedded in the bar code. Scan Transmit Without Identifiers if you want the bar code broken into packets and stripped of the AI. If you want the AI included, scan Transmit With Identifiers. Default = Off. * Off Transmit Without Identifiers Transmit With Identifiers GS1-128 Redundancy If you are encountering errors when reading GS1-128 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the GS1- 7 - 31 128 Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. GS1-128 Redundancy GS1-128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length 7 - 32 Telepen Telepen On/Off On * Off Telepen Output Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pattern 2). Default = AIM Telepen Output. * AIM Telepen Output Original Telepen Output Telepen Redundancy If you are encountering errors when reading Telepen bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the 7 - 33 Telepen Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. Telepen Redundancy Telepen Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length 7 - 34 UPC-A UPC-A On/Off * On Off UPC-A Number System and Check Digit UPC-A sample showing the number system and check digit: Number System Check Digit UPC-A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the can be programmed so it will not transmit it. Default = On. * On Off 7 - 35 UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off UPC-A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-A data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off UPC-A Addenda Required When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or 5 digit addenda listed on page 7-36. Default = Not Required. Required * Not Required 7 - 36 Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A Addenda Required (see page 7-36). Set the length (in milliseconds) for this timeout by scanning the bar code below, then setting the timeout (from 065535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 100. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches. Addenda Timeout UPC-A Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = Off. On * Off UPC-A Redundancy If you are encountering errors when reading UPC-A bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the UPCA Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. UPC-A Redundancy 7 - 37 UPC-A/EAN-13 with Extended Coupon Code Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. When left on the default setting (Off), the scanner treats Coupon Codes and Extended Coupon Codes as single bar codes. If you scan the Allow Concatenation code, when the scanner sees the coupon code and the extended coupon code in a single scan, it transmits both as separate symbologies. Otherwise, it transmits the first coupon code it reads. If you scan the Require Concatenation code, the scanner must see and read the coupon code and extended coupon code in a single read to transmit the data. No data is output unless both codes are read. Default = Off. * Off Allow Concatenation Require Concatenation UPC-A Number System 4 Addenda Required This setting programs the scanner to require a coupon code only on UPC-A bar codes that begin with a “4.” The following settings can be programmed: Require Coupon Code: All UPC-A bar codes that begin with a “4” must have a coupon code. The UPC-A bar code with the coupon code is then transmitted as a single, concatenated bar code. If a coupon code is not found within the Addenda Timeout period, the UPC-A bar code is discarded. Don’t Require Coupon Code: If you have selected Require Coupon Code, and you want to disable this feature, scan Don’t Require Coupon Code. UPC-A bar codes are transmitted, depending on the setting you are using for UPC-A/EAN-13 with Extended Coupon Code. 7 - 38 Default = Don’t Require Coupon Code. * Don’t Require Coupon Code Require Coupon Code UPC-A Number System 5 Addenda Required This setting programs the scanner to require any combination of a coupon code, a 2 digit addenda, or a 5 digit addenda on UPC-A bar codes that begin with a “5.” The following settings can be programmed: Require Coupon Code/Addenda: All UPC-A bar codes that begin with a “5” must have a coupon code, a 2 digit addenda, a 5 digit addenda, or a combination of these addenda. The UPC-A bar code with the coupon code and/or addenda is then transmitted as a single, concatenated bar code. If a coupon code and/or required addenda is not found within the Addenda Timeout period, the UPC-A bar code is discarded. Don’t Require Coupon Code/Addenda: If you have selected Require Coupon Code/Addenda, and you want to disable this feature, scan Don’t Require Coupon Code/Addenda. UPC-A bar codes are transmitted, depending on the setting you are using for UPC-A/EAN-13 with Extended Coupon Code. 7 - 39 Default = Don’t Require Coupon Code/Addenda. * Don’t Require Coupon Code/ Addenda Require 2 Digit Addenda Require 5 Digit Addenda Require 2 or 5 Digit Addenda Require Coupon Code Require Coupon Code or 2 Digit Addenda Require Coupon Code or 5 Digit Addenda Require Coupon Code, 2 Digit Addenda, or 5 Digit Addenda Addenda Timeout You can set a time during which the scanner looks for a coupon code. If a coupon code is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A/ EAN-13 with Extended Coupon Code or UPC-A Number System 4 Addenda Required. Set the length (in milliseconds) for this timeout by 7 - 40 scanning the bar code below, then setting the timeout (from 0-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 100. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches. Addenda Timeout UPC-E0 UPC-E0 On/Off Most U.P.C. bar codes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to read codes that lead with the 1 number system, use EAN/JAN-13 (page 7-45). Default = On. * UPC-E0 On UPC-E0 Off UPC-E0 Expand UPC-E Expand expands the UPC-E code to the 12 digit, UPC-A format. Default = Off. On * Off 7 - 41 UPC-E0 Number System The numeric system digit of a UPC-A symbol is normally transmitted at the beginning of scanned data. When using UPC-E Expand, the unit can be programmed so it will not transmit it. Default = On. * On Off UPC-E0 Number System and Check Digit UPC-E0 sample showing the number system and check digit: Number System Check Digit UPC-E0 Check Digit Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = Off. On * Off 7 - 42 UPC-E0 Leading Zero This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan Off. Default = Off. On * Off UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off UPC-E0 Addenda Required When Required is scanned, the scanner will only read UPC-E bar codes that have addenda. Default = Not Required. Required * Not Required 7 - 43 Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-E0 Addenda Required (page 7-43). Set the length (in milliseconds) for this timeout by scanning the bar code below, then setting the timeout (from 065535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 100. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches. Addenda Timeout UPC-E0 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = Off. On * Off UPC-E0 Redundancy If you are encountering errors when reading UPC-E0 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the UPCE0 Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 1. UPC-E0 Redundancy 7 - 44 EAN/JAN-13 EAN/JAN-13 On/Off * On Off EAN/JAN-13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off 7 - 45 EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-13 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-13 bar codes that have addenda. Default = Not Required. Required * Not Required EAN-13 Beginning with 2 Addenda Required This setting programs the scanner to require a 2 digit addenda only on EAN-13 bar codes that begin with a “2.” The following settings can be programmed: Require 2 Digit Addenda: All EAN-13 bar codes that begin with a “2” must have a 2 digit addendum. The EAN-13 bar code with the 2 digit addendum is then transmitted as a single, concatenated bar code. If a 2 digit addendum is not found within the Addenda Timeout period, the EAN13 bar code is discarded. Note: if you are using EAN-13 Beginning with 290 Addenda Required (page 7-47), that setting will take precedence over this one. 7 - 46 Don’t Require 2 Digit Addenda: If you have selected Require 2 Digit Addenda, and you want to disable this feature, scan Don’t Require 2 Digit Addenda. EAN-13 bar codes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required. Default = Don’t Require 2 Digit Addenda. * Don’t Require 2 Digit Addenda Require 2 Digit Addenda EAN-13 Beginning with 290 Addenda Required This setting programs the scanner to require a 5 digit addenda only on EAN-13 bar codes that begin with “290.” The following settings can be programmed: Require 5 Digit Addenda: All EAN-13 bar codes that begin with “290” must have a 5 digit addendum. The EAN-13 bar code with the 5 digit addendum is then transmitted as a single, concatenated bar code. If a 5 digit addendum is not found within the Addenda Timeout period, the EAN13 bar code is discarded. Note: if you are using EAN-13 Beginning with 2 Addenda Required (page 7-46), this setting will take precedence. Don’t Require 5 Digit Addenda: If you have selected Require 5 Digit Addenda, and you want to disable this feature, scan Don’t Require 5 Digit Addenda. EAN-13 bar codes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required. Default = Don’t Require 5 Digit Addenda. * Don’t Require 5 Digit Addenda Require 5 Digit Addenda EAN-13 Beginning with 378/379 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 bar codes that begin with a “378” or “379.” The following settings can be programmed: 7 - 47 Require Addenda: All EAN-13 bar codes that begin with a “378” or “379” must have a 2 digit addenda, a 5 digit addenda, or a combination of these addenda. The EAN-13 bar code with the addenda is then transmitted as a single, concatenated bar code. If the required addenda is not found within the Addenda Timeout period, the EAN-13 bar code is discarded. Don’t Require Addenda: If you have selected Require Addenda, and you want to disable this feature, scan Don’t Require Addenda. EAN-13 bar codes are transmitted, depending on the setting you are using for EAN/ JAN-13 Addenda Required. Default = Don’t Require Addenda. * Don’t Require Addenda Require 2 Digit Addenda Require 5 Digit Addenda Require 2 or 5 Digit Addenda EAN-13 Beginning with 414/419 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 bar codes that begin with a “414” or “419.” The following settings can be programmed: Require Addenda: All EAN-13 bar codes that begin with a “414” or “419” must have a 2 digit addenda, a 5 digit addenda, or a combination of these addenda. The EAN-13 bar code with the addenda is then transmitted as a single, concatenated bar code. If the required addenda is not found within the Addenda Timeout period, the EAN-13 bar code is discarded. Don’t Require Addenda: If you have selected Require Addenda, and you want to disable this feature, scan Don’t Require Addenda. EAN-13 bar codes are transmitted, depending on the setting you are using for EAN/ JAN-13 Addenda Required. 7 - 48 Default = Don’t Require Addenda. * Don’t Require Addenda Require 2 Digit Addenda Require 5 Digit Addenda Require 2 or 5 Digit Addenda EAN-13 Beginning with 434/439 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 bar codes that begin with a “434” or “439.” The following settings can be programmed: Require Addenda: All EAN-13 bar codes that begin with a “434” or “439” must have a 2 digit addenda, a 5 digit addenda, or a combination of these addenda. The EAN-13 bar code with the addenda is then transmitted as a single, concatenated bar code. If the required addenda is not found within the Addenda Timeout period, the EAN-13 bar code is discarded. Don’t Require Addenda: If you have selected Require Addenda, and you want to disable this feature, scan Don’t Require Addenda. EAN-13 bar codes are transmitted, depending on the setting you are using for EAN/ JAN-13 Addenda Required. 7 - 49 Default = Don’t Require Addenda. * Don’t Require Addenda Require 2 Digit Addenda Require 5 Digit Addenda Require 2 or 5 Digit Addenda EAN-13 Beginning with 977 Addenda Required This setting programs the scanner to require a 2 digit addenda only on EAN-13 bar codes that begin with “977.” The following settings can be programmed: Require 2 Digit Addenda: All EAN-13 bar codes that begin with “977” must have a 2 digit addendum. The EAN-13 bar code with the 2 digit addendum is then transmitted as a single, concatenated bar code. If a 2 digit addendum is not found within the Addenda Timeout period, the EAN13 bar code is discarded. Don’t Require 2 Digit Addenda: If you have selected Require 2 Digit Addenda, and you want to disable this feature, scan Don’t Require 2 Digit Addenda. EAN-13 bar codes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required. Default = Don’t Require 2 Digit Addenda. * Don’t Require 2 Digit Addenda Require 2 Digit Addenda EAN-13 Beginning with 978 Addenda Required These settings program the scanner to require a 5 digit addenda only on EAN-13 bar codes that begin with “978.” The following settings can be programmed: 7 - 50 Require 5 Digit Addenda: All EAN-13 bar codes that begin with “978” must have a 5 digit addendum. The EAN-13 bar code with the 5 digit addendum is then transmitted as a single, concatenated bar code. If a 5 digit addendum is not found within the Addenda Timeout period, the EAN13 bar code is discarded. Don’t Require 5 Digit Addenda: If you have selected Require 5 Digit Addenda, and you want to disable this feature, scan Don’t Require 5 Digit Addenda. EAN-13 bar codes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required. Default = Don’t Require 5 Digit Addenda. * Don’t Require 5 Digit Addenda Require 5 Digit Addenda EAN-13 Beginning with 979 Addenda Required These settings program the scanner to require a 5 digit addenda only on EAN-13 bar codes that begin with “979.” The following settings can be programmed: Require 5 Digit Addenda: All EAN-13 bar codes that begin with “979” must have a 5 digit addendum. The EAN-13 bar code with the 5 digit addendum is then transmitted as a single, concatenated bar code. If a 5 digit addendum is not found within the Addenda Timeout period, the EAN13 bar code is discarded. Don’t Require 5 Digit Addenda: If you have selected Require 5 Digit Addenda, and you want to disable this feature, scan Don’t Require 5 Digit Addenda. EAN-13 bar codes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required. Default = Don’t Require 5 Digit Addenda. * Don’t Require 5 Digit Addenda Require 5 Digit Addenda 7 - 51 Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for EAN/JAN-13 Addenda Required. Set the length (in milliseconds) for this timeout by scanning the bar code below, then setting the timeout (from 0-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 100. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches. Addenda Timeout EAN/JAN-13 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = Off. On * Off Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon Code (page 7-38). EAN/JAN-13 Redundancy If you are encountering errors when reading EAN/JAN-13 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the EAN/JAN-13 Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. EAN/JAN-13 Redundancy 7 - 52 ISBN Translate ISBNs are printed on books using the EAN-13 bar code symbology. To translate EAN-13 Bookland symbols into their equivalent ISBN number format, scan the On bar code below. Default = Off. On * Off Convert ISBN to 13-Digit When translating EAN-13 codes to the ISBN format, you can convert the bar code to a 13 digit format by scanning the Convert to 13-Digit On bar code below. Default = Convert to 13-Digit Off. Convert to 13-Digit On *Convert to 13-Digit Off ISBN Reformat In normal use, the first two or three digits of an EAN-13 bar code identify the country of origin. The country prefixes are 978 and 979. To reformat ISBN codes so the country prefix is dropped out, scan the Reformat On bar code below. Default = Reformat Off. Reformat On *Reformat Off 7 - 53 ISSN Translate When On is scanned, EAN-13 977 Bookland symbols are translated into their equivalent 8-digit ISSN number format. For example, 9770123456787 will be transmitted as 01234560. Default = Off. On * Off ISSN Reformat When Reformat On is scanned, EAN-13 977 Bookland symbols are translated into their equivalent 8-digit ISSN number format, with hyphens added to the output. For example, 9770123456787 will be transmitted as 0123-456-0. (You must first scan ISSN On (page 7-54) before scanning Reformat On.) Default = Reformat Off. Reformat On * Reformat Off 7 - 54 EAN/JAN-8 EAN/JAN-8 On/Off * On Off EAN/JAN-8 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off 7 - 55 EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that have addenda. Default = Not Required. Required * Not Required Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for EAN/JAN-8 Addenda Required. Set the length (in milliseconds) for this timeout by 7 - 56 scanning the bar code below, then setting the timeout (from 0-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 100. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches. Addenda Timeout EAN/JAN-8 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = Off. On * Off EAN/JAN-8 Redundancy If you are encountering errors when reading EAN/JAN-8 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the ba code. To adjust the redundancy, scan the EAN/JAN-8 Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. EAN/JAN-8 Redundancy 7 - 57 MSI MSI On/Off On * Off MSI Check Character Different types of check characters are used with MSI bar codes. You can program the scanner to read MSI bar codes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI bar codes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data. 7 - 58 When Check Character is set to Validate Type 10/11, but Don’t Transmit, the unit will only read MSI bar codes printed with the specified type check character(s), but will not transmit the check character(s) with the scanned data. * Validate Type 10, but Don’t Transmit Validate Type 10 and Transmit Validate 2 Type 10 Characters, but Don’t Transmit Validate 2 Type 10 Characters and Transmit Validate Type 10 then Type 11 Character, but Don’t Transmit Validate Type 10 then Type 11 Character and Transmit Disable MSI Check Characters MSI Redundancy If you are encountering errors when reading MSI bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the MSI Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. MSI Redundancy 7 - 59 MSI Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length Plessey Code < Default All Plessey Code Settings > Plessey Code On/Off On * Off Plessey Check Character No Check Character indicates that the scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate, but Don’t Transmit, the unit only reads Plessey bar codes printed with a check character, but will not transmit the check character with the scanned data. 7 - 60 When Check Character is set to Validate and Transmit, the scanner only reads Plessey bar codes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Character. * No Check Character Validate, but Don’t Transmit Validate and Transmit Plessey Redundancy If you are encountering errors when reading Plessey bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the Plessey Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. Plessey Redundancy Plessey Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length 7 - 61 GS1 DataBar Omnidirectional < Default All GS1 DataBar Omnidirectional Settings > GS1 DataBar Omnidirectional On/Off * On Off GS1 DataBar Omnidirectional Redundancy If you are encountering errors when reading GS1 DataBar Omnidirectional bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the GS1 DataBar Omnidirectional Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. GS1 DataBar Omnidirectional Redundancy 7 - 62 GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off * On Off GS1 DataBar Limited Redundancy If you are encountering errors when reading GS1 DataBar Limited bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the GS1 DataBar Limited Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. GS1 DataBar Limited Redundancy 7 - 63 GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On Off GS1 DataBar Expanded Redundancy If you are encountering errors when reading GS1 DataBar Expanded bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the GS1 DataBar Expanded Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. GS1 DataBar Expanded Redundancy 7 - 64 GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length Trioptic Code Trioptic Code is used for labeling magnetic storage media. On * Off GS1 Emulation The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1-128, and GS1-128 DataBar and GS1 Composites. (Any application that accepts GS1 data can be simplified since it only needs to recognize one data carrier type.) If GS1-128 Emulation is scanned, all retail codes (U.P.C., UPC-E, EAN8, EAN13) are expanded out to 16 digits. If the AIM ID is enabled, the value will be the GS1-128 AIM ID, ]C1 (see Symbology Chart on page A-1). If GS1 DataBar Emulation is scanned, all retail codes (U.P.C., UPC-E, EAN8, EAN13) are expanded out to 16 digits. If the AIM ID is enabled, the value will be the GS1-DataBar AIM ID, ]em (see Symbology Chart on page A-1). If GS1 Code Expansion Off is scanned, retail code expansion is disabled, and UPC-E expansion is controlled by the UPC-E0 Expand (page 7-41) setting. If the AIM ID is enabled, the value will be the GS1-128 AIM ID, ]C1 (see Symbology Chart on page A-1). 7 - 65 If EAN8 to EAN13 Conversion is scanned, all EAN8 bar codes are converted to EAN13 format. Default = GS1 Emulation Off. GS1-128 Emulation GS1 DataBar Emulation GS1 Code Expansion Off EAN8 to EAN13 Conversion * GS1 Emulation Off Postal Codes The following lists linear postal codes. Any combination of linear postal code selections can be active at a time. China Post (Hong Kong 2 of 5) 7 - 66 China Post (Hong Kong 2 of 5) On/Off On * Off China Post (Hong Kong 2 of 5) Redundancy If you are encountering errors when reading China Post (Hong Kong 2 of 5) bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the China Post (Hong Kong 2 of 5) Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. China Post (Hong Kong 2 of 5) Redundancy China Post (Hong Kong 2 of 5) Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length 7 - 67 7 - 68 8 Interface Keys Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can be used with the scanner. Refer to page 2-17 enable Control + ASCII mode. Function Code NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US HEX/ASCII Value 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F Full ASCII “CTRL” + 8-1 The last five characters in the Full ASCII “CTRL”+ column ( [ \ ] 6 - ), apply to US only. The following chart indicates the equivalents of these five characters for different countries. Note: Not all countries may be supported by your device. Country Codes United States Belgium Scandinavia France Germany à Italy Switzerland .. ¢ United Kingdom Denmark Norway Spain Supported Interface Keys ASCII HEX IBM AT/XT and PS/2 Compatibles, WYSE PC/AT Supported Keys NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF 00 01 02 03 04 05 06 07 08 09 0A 0B 0C Reserved Enter (KP) Cap Lock ALT make ALT break CTRL make CTRL break CR/Enter Reserved Tab Reserved Tab Delete 8-2 Apple Mac/iMac Supported Keys Reserved Enter/Numpad Enter CAPS ALT make ALT break CNTRL make CNTRL break RETURN APPLE make TAB APPLE break TAB Del ASCII HEX CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US DEL 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 7F IBM AT/XT and PS/2 Compatibles, WYSE PC/AT Supported Keys CR/Enter Insert Escape F11 Home Print Back Space Back Tab F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 Apple Mac/iMac Supported Keys RETURN Ins Help ESC F11 Home Prnt Scrn BACKSPACE LSHIFT TAB F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 BACKSPACE 8-3 8-4 9 Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Chart, beginning on page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D. prefix for all symbologies. This is a temporary setting that will be removed when the unit is power cycled. Add Code I.D. Prefix to All Symbologies (Temporary) Show Software Revision Scan the bar code below to output the current software revision, unit serial number, and other product information for both the scanner and base. Show Revision Show Data Format Scan the bar code below to show current data format settings. DFMBK3?. Data Format Settings 9-1 Test Menu When you scan the Test Menu On code, then scan a programming code in this manual, the scanner displays the content of a programming code. The programming function will still occur, but in addition, the content of that programming code is output to the terminal. Note: This feature should not be used during normal scanner operation. On * Off EZConfig-Scanning Introduction EZConfig-Scanning provides a wide range of PC-based programming functions that can be performed on a scanner connected to your PC's COM port. EZConfig-Scanning allows you to download upgrades to the scanner's firmware, change programmed parameters, and create and print programming bar codes. Using EZConfig-Scanning, you can even save/open the programming parameters for a scanner. This saved file can be e-mailed or, if required, you can create a single bar code that contains all the customized programming parameters and mail or fax that bar code to any location. Users in other locations can scan the bar code to load in the customized programming. To communicate with a scanner, EZConfig-Scanning requires that the PC have at least one available serial communication port, or a serial port emulation using a physical USB port. If you are using the serial port and RS232 cable, an external power supply is required. When using a USB serial port emulation, only a USB cable is required. EZConfig-Scanning Operations The EZConfig-Scanning software performs the following operations: Scan Data Scan Data allows you to scan bar codes and display the bar code data in a window. Scan Data lets you send serial commands to the scanner and receive scanner response that can be seen in the Scan Data window. The data displayed in the Scan Data window can either be saved in a file or printed. Configure Configure displays the programming and configuration data of the scanner. The scanner's programming and configuration data is grouped into different categories. Each category is displayed as a tree 9-2 item under the “Configure” tree node in the application explorer. When one of these tree nodes is clicked, the right-hand side is loaded with the parameters' form belonging to that particular category. The Configure tree option has all the programming and configuration parameters specified for a scanner. You can set or modify these parameters as required. You can later write the modified settings to the scanner, or save them to a dcf file. Installing EZConfig-Scanning from the Web Note: EZConfig-Scanning requires .NET framework. If .NET is not installed on your PC, you will be prompted to install it during the EZConfig-Scanning installation. 1. Access the Honeywell web site at www.honeywellaidc.com 2. Click on the Downloads tab. Select Software. 3. Click on the dropdown for Select Product Number and select the number of your product. 4. Click on the listing for EZConfig-Scanning. 5. Follow the security directions as prompted on the screen. 6. When prompted, select Save, and save the file to the c:\windows\temp directory. 7. Once you have finished downloading the file, exit the web site. 8. Using Explorer, go to the c:\windows\temp file. 9. Double click on the EZConfig-Scanning Setup.exe file. Follow the screen prompts to install the EZConfig-Scanning program. 10. If you’ve selected the defaults during installation, you can click on Start Menu-All Programs-Honeywell-EZConfig-Scanning. 9-3 9-4 10 Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will program the scanner. For complete descriptions and examples of each serial programming command, refer to the corresponding programming bar code in this manual. The device must be set to an RS232 interface (see page 2-1). The following commands can be sent via a PC COM port using terminal emulation software. Conventions The following conventions are used for menu and query command descriptions: parameter A label representing the actual value you should send as part of a command. An optional part of a command. [option] {Data} Alternatives in a command. bold Names of menus, menu commands, buttons, dialog boxes, and windows that appear on the screen. Menu Command Syntax Menu commands have the following syntax (spaces have been used for clarity only): Prefix [:Name:] Tag SubTag {Data} [, SubTag {Data}] [; Tag SubTag {Data}] […] Storage Prefix Three ASCII characters: SYN M CR (ASCII 22,77,13). :Name: To send information to the scanner (with the base connected to host), use :Voyager: The default factory setting for a Voyager scanner is Voyager scanner. If the name is not known, a wildcard (*) can be used :*:. Note: Since the base stores all work group settings and transfers to them to scanner once they are linked, changes are typically done to the base and not to the scanner. Tag A 3 character case-insensitive field that identifies the desired menu command group. For example, all RS232 configuration settings are identified with a Tag of 232. SubTag A 3 character case-insensitive field that identifies the desired menu command within the tag group. For example, the SubTag for the RS232 baud rate is BAD. Data The new value for a menu setting, identified by the Tag and SubTag. 10 - 1 Storage A single character that specifies the storage table to which the command is applied. An exclamation point (!) performs the command’s operation on the device’s volatile menu configuration table. A period (.) performs the command’s operation on the device’s non-volatile menu configuration table. Use the non-volatile table only for semi-permanent changes you want saved through a power cycle. Query Commands Several special characters can be used to query the device about its settings. What is the default value for the setting(s). What is the device’s current value for the setting(s). What is the range of possible values for the setting(s). (The device’s response uses a dash (-) to indicate a continuous range of values. A pipe (|) separates items in a list of non-continuous values.) :Name: Field Usage (Optional) This command returns the query information from the scanner. Tag Field Usage When a query is used in place of a Tag field, the query applies to the entire set of commands available for the particular storage table indicated by the Storage field of the command. In this case, the SubTag and Data fields should not be used because they are ignored by the device. SubTag Field Usage When a query is used in place of a SubTag field, the query applies only to the subset of commands available that match the Tag field. In this case, the Data field should not be used because it is ignored by the device. Data Field Usage When a query is used in place of the Data field, the query applies only to the specific command identified by the Tag and SubTag fields. Concatenation of Multiple Commands Multiple commands can be issued within one Prefix/Storage sequence. Only the Tag, SubTag, and Data fields must be repeated for each command in the sequence. If additional commands are to be applied to the same Tag, then the new command sequence is separated with a comma (,) and only the SubTag and Data fields of the additional command are issued. If the additional command requires a different Tag field, the command is separated from previous commands by a semicolon (;). 10 - 2 Responses The device responds to serial commands with one of three responses: ACK Indicates a good command which has been processed. ENQ Indicates an invalid Tag or SubTag command. NAK Indicates the command was good, but the Data field entry was out of the allowable range for this Tag and SubTag combination, e.g., an entry for a minimum message length of 100 when the field will only accept 2 characters. When responding, the device echoes back the command sequence with the status character inserted directly before each of the punctuation marks (the period, exclamation point, comma, or semicolon) in the command. Examples of Query Commands In the following examples, a bracketed notation [ ] depicts a non-displayable response. Example: What is the range of possible values for Codabar Coding Enable? Enter: cbrena*. Response: CBRENA0-1[ACK] This response indicates that Codabar Coding Enable (CBRENA) has a range of values from 0 to 1 (off and on). Example: What is the default value for Codabar Coding Enable? Enter: cbrena^. Response: CBRENA1[ACK] This response indicates that the default setting for Codabar Coding Enable (CBRENA) is 1, or on. Example: What is the device’s current setting for Codabar Coding Enable? Enter: cbrena?. Response: CBRENA1[ACK] This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on. Example: What are the device’s settings for all Codabar selections? Enter: cbr?. Response: CBRENA1[ACK], SSX0[ACK], CK20[ACK], CCT1[ACK], MIN2[ACK], 10 - 3 MAX60[ACK], DFT[ACK]. This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on; the Start/Stop Character (SSX) is set to 0, or Don’t Transmit; the Check Character (CK2) is set to 0, or Not Required; concatenation (CCT) is set to 1, or Enabled; the Minimum Message Length (MIN) is set to 2 characters; the Maximum Message Length (MAX) is set to 60 characters; and the Default setting (DFT) has no value. Serial Trigger Commands You can activate and deactivate the scanner with serial trigger commands. The button is activated and deactivated by sending the following commands: Activate: SYN T CR Deactivate: SYN U CR The scanner scans until a bar code has been read or until the deactivate command is sent. The scanner can also be set to turn itself off after a specified time has elapsed (see Read Time-Out, which follows). Read Time-Out Use this selection to set a time-out (in milliseconds) of the scanner’s button when using serial commands to trigger the scanner. Once the scanner has timed out, you can activate the scanner either by pressing the button or using a serial trigger command. After scanning the Read Time-Out bar code, set the time-out duration (from 0-300,000 milliseconds) by scanning digits on the Programming Chart inside the back cover, then scanning Save. Default = 30,000 ms. Read Time-Out Resetting the Standard Product Defaults If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want the factory default settings restored, scan the Standard Product Default Settings bar code below. Standard Product Default Settings 10 - 4 The charts on the following pages list the factory default settings for each of the commands (indicated by an asterisk (*) on the programming pages). 10 - 5 Menu Commands Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page Product Default Settings Setting Custom Defaults Set Custom Defaults MNUCDF 1-9 Save Custom Defaults DEFALT 1-9 Resetting the Custom Defaults Activate Custom Defaults DEFALT 1-10 Resetting the Factory Defaults Remove Custom Defaults DEFOVR 1-10 Activate Defaults DEFALT 1-10 Keyboard Wedge: IBM PC AT and Compatibles with CR suffix PAP_AT 2-1 IBM PS2 Keyboard PAPPS2 2-1 RS232 Serial Port PAP232 2-2 IBM Port 5B Interface PAPP5B 2-2 IBM Port 9B HHBCR-1 Interface PAP9B1 2-2 IBM Port 17 Interface PAPP17 2-2 IBM Port 9B HHBCR-2 Interface PAP9B2 2-2 OPOS Mode OPOS Mode PAPOPS 2-3 Plug and Play Codes: IBM SurePos USB IBM SurePos Handheld PAPSPH 2-4 USB IBM SurePos Tabletop PAPSPT 2-4 * Enable Secondary Interface REMIFC1 2-4 Disable Secondary Interface REMIFC0 2-4 Programming the Interface Plug and Play Codes Plug and Play Codes: RS485 IBM Secondary Interface 10 - 6 Selection Plug and Play Codes: USB HID Fallback Mode Setting Serial Command * Indicates default # Indicates a numeric entry Page USB Keyboard (PC) PAP124 2-5 USB Keyboard (Mac) PAP125 2-5 USB Japanese Keyboard (PC) PAP134 2-5 USB HID PAP131 2-5 HID Fallback Mode (Range 0-60 *5 minutes USBFTO 2-6 10 - 7 Selection USB Serial Commands 10 - 8 Setting Serial Command # Indicates a numeric entry Page USB Serial Emulation for Windows XP, Windows Server 2003, and later PAP130 2-6 USB Serial Emulation for Windows 2000 REMIFCO;PAP130 2-6 CTS/RTS Emulation On USBCTS1 2-6 CTS/RTS Emulation Off* USBCTS0 2-6 ACK/NAK Mode On USBACK1 2-7 ACK/NAK Mode Off* USBACK0 2-7 Communication Timeout (Range 0-65535) *2000 ms 232DLK##### 2-7 Timeout Retries HSTRTY 2-7 Communication Timeout Beeper Off HSTTOA0 2-8 *Communication Timeout Beeper On HSTTOA1 2-8 NAK Retries (Range 0-255) *0 HSTRTN### 2-8 BEL/CAN Mode On BELCAN1 2-8 BEL/CAN Mode Off* BELCAN0 2-8 * Indicates default Selection Plug and Play Codes Setting Serial Command # Indicates a numeric entry Page Verifone Ruby Terminal PAPRBY 2-9 Gilbarco Terminal PAPGLB 2-9 Honeywell Bioptic Aux Port PAPBIO 2-10 Datalogic Magellan Bioptic Aux Port PAPMAG 2-10 NCR Bioptic Aux Port PAPNCR 2-10 Wincor Nixdorf Terminal PAPWNX 2-11 Wincor Nixdorf Beetle PAPBTL 2-12 * Indicates default 10 - 9 Selection Program Keyboard Country Setting Serial Command * Indicates default # Indicates a numeric entry Page *U.S.A. KBDCTY0 2-13 Arabic KBDCTY91 2-13 Belgium KBDCTY1 2-13 Chinese KBDCTY92 2-13 Finland KBDCTY2 2-13 France KBDCTY3 2-13 Germany KBDCTY4 2-13 Hungary KBDCTY19 2-13 IBM Financial KBDCTY90 2-13 Italy KBDCTY5 2-13 Japan ASCII KBDCTY28 2-13 Korea KBDCTY93 2-13 Russia KBDCTY26 2-14 Slovenia KBDCTY31 2-14 Spain KBDCTY10 2-14 Switzerland (German) KBDCTY6 2-14 Thailand KBDCTY94 2-14 Turkey Q KBDCTY24 2-14 United Kingdom KBDCTY7 2-14 Vietnam KBDCTY95 2-14 *Off KBDALT0 2-15 3 Characters KBDALT6 2-15 4 Characters KBDALT7 2-15 *Regular KBDSTY0 2-15 Caps Lock KBDSTY1 2-15 Shift Lock KBDSTY2 2-15 Autocaps via NumLock KBDSTY7 2-16 Emulate External Keyboard KBDSTY5 2-16 Keyboard Wedge Modifiers ALT Mode Keyboard Style 10 - 10 Selection Keyboard Conversion Keyboard Modifiers Setting Serial Command # Indicates a numeric entry Page *Keyboard Conversion Off KBDCNV0 2-16 Convert all Characters to Upper Case KBDCNV1 2-16 Convert all Characters to Lower Case KBDCNV1 2-16 * Indicates default *Control + ASCII Off KBDCAS0 2-17 DOS Mode Control + ASCII KBDCAS1 2-17 Windows Mode Control + ASCII KBDCAS2 2-17 Windows Mode Prefix/Suffix Off KBDCAS3 2-17 *Numeric Keypad Off KBDNPS0 2-17 Numeric Keypad On KBDNPS1 2-17 Inter-Scan Code Delay Inter-Scan Code Delay *0 (Range 1-30 msecs) KBDDLY## 2-18 Break Character Suppress Break Character KBDF0B0 2-18 *Transmit Break Character KBDF0B1 2-18 Reset Keyboard Wedge Defaults KBDDFT 2-18 Keyboard Wedge Defaults 10 - 11 Selection Setting Serial Command * Indicates default # Indicates a numeric entry Page RS-232 Modifiers RS232 Baud Rate 10 - 12 300 BPS 232BAD0 2-19 600 BPS 232BAD1 2-19 1200 BPS 232BAD2 2-19 2400 BPS 232BAD3 2-19 4800 BPS 232BAD4 2-19 *9600 BPS 232BAD5 2-19 19200 BPS 232BAD6 2-19 38400 BPS 232BAD7 2-19 57600 BPS 232BAD8 2-19 115200 BPS 232BAD9 2-19 Selection Word Length: Data Bits, Stop Bits, and Parity Setting Serial Command * Indicates default # Indicates a numeric entry Page 7 Data, 1 Stop, Parity Even 232WRD3 2-20 7 Data, 1 Stop, Parity None 232WRD0 2-20 7 Data, 1 Stop, Parity Odd 232WRD6 2-20 7 Data, 2 Stop, Parity Even 232WRD4 2-20 7 Data, 2 Stop, Parity None 232WRD1 2-20 7 Data, 2 Stop, Parity Odd 232WRD7 2-20 8 Data, 1 Stop, Parity Even 232WRD5 2-20 *8 Data, 1 Stop, Parity None 232WRD2 2-20 8 Data, 1 Stop, Parity Odd 232WRD8 2-20 7 Data, 1 Stop, Parity Space 232WRD9 2-20 7 Data, 2 Stop, Parity Space 232WRD10 2-21 8 Data, 1 Stop, Parity Space 232WRD11 2-21 7 Data, 1 Stop, Parity Mark 232WRD12 2-21 7 Data, 2 Stop, Parity Mark 232WRD13 2-21 8 Data, 1 Stop, Parity Mark 232WRD14 2-21 10 - 13 Selection RS232 Handshaking RS232 Defaults NCR Modifiers 10 - 14 Setting Serial Command * Indicates default # Indicates a numeric entry Page *RTS/CTS Off 232CTS0 2-22 Flow Control, No Timeout 232CTS1 2-22 Character-Based Flow Control, No Timeout 232CTS7 2-22 Two-Direction Flow Control 232CTS2 2-22 Flow Control with Timeout 232CTS3 2-22 Character-Based Flow Control with Timeout 232CTS9 2-22 RS232 Timeout (Range 1-5100) *1000 ms 232DEL#### 2-22 *XON/XOFF Off 232XON0 2-23 XON/XOFF On 232XON1 2-23 *ACK/NAK Off 232ACK0 2-23 ACK/NAK On 232ACK1 2-23 Communication Timeout (Range 1-65535) *2000 ms 232DLK##### 2-23 Communication Timeout Beeper Off HSTTOA0 2-24 *Communication Timeout Beeper On HSTTOA1 2-24 BEL/CAN Mode On BELCAN1 2-25 *BEL/CAN Mode Off BELCAN0 2-25 Reset RS232 Defaults 232DFT 2-25 Selection NCR ACK/NAK Setting Serial Command * Indicates default # Indicates a numeric entry Page *NCR ACK/NAK Off NCRACK0 2-25 NCR ACK/NAK On NCRACK1 2-25 Block Check Character *Transmit NCRBCC1 2-26 Don’t Transmit NCRBCC0 2-26 NCR Prefix/Suffix NCR Prefix NCRPR2## 2-26 NCR Suffix NCRSF2## 2-26 Transmit Prefix/ Suffix NCRBCP1 2-27 *Don’t Transmit Prefix/Suffix NCRBCP0 2-27 NCR NOF (Not-onFile) Error On NCRRAZ1 2-27 *Off NCRRAZ0 2-27 Scanner to Bioptic Communication *Packet Mode Off 232PKT0 2-28 Packet Mode On 232PKT2 2-28 *ACK/NAK Off 232ACK0 2-28 ACK/NAK On 232ACK1 2-28 Communication Timeout (Range 1-65535) *2000 ms 232DLK##### 2-28 Cordless System Operation Note: This section applies only to cordless systems. It does not apply to corded scanners. Base Power Communication Indicator *On :*:BASRED1 3-7 Off :*:BASRED0 3-7 Reset Scanner Reset Scanner RESET_ 3-8 Scanning While in Base Cradle Scanning in Cradle Off BT_SIC0 3-8 *Scanning in Cradle On BT_SIC1 3-8 *On BEPPGE1 3-9 Off BEPPGE0 3-9 Paging Mode 10 - 15 Setting Serial Command # Indicates a numeric entry Page Low (*1000) (min 100Hz) BEPPFQ1000 3-9 Medium (3250) BEPPFQ3250 3-9 High (4200) (min 5000Hz) BEPPFQ4200 3-9 Scanner Address Scanner Address BT_LDA 3-9 Base Address Base Address :*:BASLDA 3-10 Scanner Modes Charge Only Mode :*:BASLNK0 3-10 *Charge and Link Mode :*:BASLNK1 3-10 Locked Link Mode :*:BASCON0 3-11 *Open Link Mode :*:BASCON1 3-11 Unlink Scanner BT_RMV 3-11 Override Locked Scanner BT_RPL1 3-12 Selection Paging Pitch Out-of-Range Alarm Scanner Power Time-Out Timer Batch Mode 10 - 16 * Indicates default *Alarm Off BT_ORW0 3-12 Alarm On BT_ORW1 3-12 Scanner Alarm Duration (Range 1 3000 sec (*1)) BT_ORD 3-12 Timer (0-7200 seconds) BT_LPT0 3-13 200 Seconds BT_LPT200 3-13 400 Seconds BT_LPT400 3-13 900 Seconds BT_LPT900 3-13 3600 Seconds BT_LPT3600 3-13 7200 Seconds BT_LPT7200 3-13 Automatic Batch Mode BATENA1 3-14 *Batch Mode Off BATENA0 3-14 Inventory Batch Mode BATENA2 3-14 Setting Serial Command * Indicates default # Indicates a numeric entry Page Batch Mode Beep Off BATBEP0 3-14 *On BATBEP1 3-14 Batch Mode Quantity *Off BATQTY0 3-15 On BATQTY1 3-15 Quantity Codes BATNUM0 3-16 BATNUM1 3-16 BATNUM2 3-16 BATNUM3 3-16 BATNUM4 3-16 BATNUM5 3-16 BATNUM6 3-16 BATNUM7 3-16 BATNUM8 3-16 BATNUM9 3-16 Delete Last Code BATUND 3-17 *Record Counter Off BATENT0 3-17 Record Counter On BATENT1 3-17 Selection Delete Last Code Record Counter Total Records Total Records BATNRC 3-17 Batch Mode Output Order FIFO BATLIF0 3-18 LIFO BATLIF1 3-18 Clear All Codes After Transmission *Don’t Clear All Codes After Transmission BATCLX0 3-18 Clear All Codes After Transmission BATCLX1 3-18 Clear All Codes Clear All Codes BATCLR 3-18 Transmit Records Automatically *Don’t Transmit Records Automatically BATATX0 3-19 Transmit Records Automatically BATATX1 3-19 Transmit Inventory Records BAT_TX 3-19 Transmit Records to Host 10 - 17 Selection Batch Mode Transmit Delay Setting Serial Command * Indicates default # Indicates a numeric entry Page *Off BATDLY0 3-20 Short (ms) BATDLY250 3-20 Medium (ms) BATDLY500 3-20 Long (ms) BATDLY1000 3-20 Scanner Name Scanner Name BT_NAM 3-21 Bluetooth Connection Non-Base BT Connection BT_DNG9 3-22 Base BT Connection BT_DNG8 3-22 Bluetooth PIN Code Bluetooth PIN *0000 BT_PIN 3-22 Auto Reconnect Mode *Auto Reconnect On BT_ACM1 3-23 Auto Reconnect Off BT_ACM0 3-23 Maximum Link Attempts Maximum Link Attempts Range 0-255 (*0) BT_MLA### 3-24 Relink Time-Out Relink Time-Out Range 0-100 (*3) BT_RLT### 3-24 Reset Reset Base RESET_ 3-25 Reset Scanner :*:RESET_ 3-25 Power Up Beeper Off - Scanner BEPPWR0 4-1 *Power Up Beeper On - Scanner BEPPWR1 4-1 Beep on BEL Character Beep on BEL On BELBEP1 4-1 *Beep on BEL Off BELBEP0 4-1 Beeper - Good Read Off BEPBEP0 4-2 *On BEPBEP1 4-2 Off BEPLVL0 4-2 Low BEPLVL1 4-2 Medium BEPLVL2 4-2 *High BEPLVL3 4-2 Input/Output Selections Power Up Beeper Beeper Volume Good Read 10 - 18 Selection Beeper Pitch - Good Read (Frequency) Beeper - Transmit Order Beeper Pitch - Error (Frequency) Setting Serial Command * Indicates default # Indicates a numeric entry Page Low (1600 Hz) BEPFQ11600 4-3 *Medium (2350 Hz) BEPFQ12350 4-3 High (4200 Hz) BEPFQ14200 4-3 *Before Transmission BEPWHN1 4-3 After Transmission BEPWHN2 4-3 *Razz (100 Hz) BEPFQ2100 4-3 Medium (2000 Hz) BEPFQ22000 4-3 High (4200 Hz) BEPFQ24200 4-3 Beeper Duration Good Read *Normal Beep BEPBIP0 4-4 Short Beep BEPBIP1 4-4 Number of Beeps Good Read Range 1 - 9 (*1) BEPRPT# 4-4 Number of Beeps Error Range 1 - 9 (*1) BEPERR# 4-5 10 - 19 Selection LED Settings 10 - 20 Setting Serial Command * Indicates default # Indicates a numeric entry Page Red LED Off LEDFN10 4-6 Green LED Off LEDFN20 4-6 Red LED On with Good Scan LEDFN11 4-6 *Green LED On with Good Scan LEDFN21 4-6 *Red LED On with Laser LEDFN12 4-6 Green LED On with Laser LEDFN22 4-6 Red LED On when CodeGate Disabled LEDFN14 4-6 Green LED On when CodeGate Disabled LEDFN24 4-6 Red LED On when In-Stand LEDFN18 4-6 Green LED On when In-Stand LEDFN28 4-6 Red LED On with CTS LEDFN1128 4-7 Green LED On with CTS LEDFN2128 4-7 Red LED when Battery is Low LEDFN11024 Green LED when Battery is Low LEDFN21024 Selection LED Brightness Setting Serial Command * Indicates default # Indicates a numeric entry Page Red Off LEDIN10 4-8 Green Off LEDIN20 4-8 Red Low LEDIN11 4-8 Green Low LEDIN21 4-8 Red Medium LEDIN12 4-8 Green Medium LEDIN22 4-8 *Red High LEDIN13 4-8 *Green High LEDIN23 4-8 10 - 21 Selection In-Stand and Out-ofStand Settings 10 - 22 Setting Serial Command * Indicates default # Indicates a numeric entry Page In-Stand Defaults AISDFT 4-9 Out-of-Stand Defaults AOSDFT 4-9 Presentation Mode Out-of-Stand PAPPM1 4-9 Presentation Mode with CodeGate Outof-Stand PAPPM2 4-9 Manual Activation Mode Off In-Stand AISMEN0 4-10 *Manual Activation Mode On In-Stand AISMEN1 4-10 Manual Activation Mode Off Out-ofStand AOSMEN0 4-10 *Manual Activation Mode On Out-ofStand AOSMEN1 4-10 Do Not End Manual Activation After Good Read In-Stand AISMGD0 4-10 *End Manual Activation After Good Read In-Stand AISMGD1 4-10 Do Not End Manual Activation After Good Read Out-ofStand AOSMGD0 4-10 *End Manual Activation After Good Read Out-ofStand AOSMGD1 4-10 Laser Timeout Button Hold InStand (Range 1 - 65525) *5000 ms AISMPT##### 4-11 Selection In-Stand and Out-ofStand Settings (continued) Setting Serial Command # Indicates a numeric entry Page Laser Timeout Button Release InStand (Range 1 - 65525) *0 ms AISMRT##### 4-11 Laser Timeout Button Hold Out-ofStand (Range 1 - 65525) *5000 ms AOSMPT##### 4-11 Laser Timeout Button Release Outof-Stand (Range 1 - 65525) *0 ms AOSMRT##### 4-11 *CodeGate Off InStand AISCGD0 4-12 CodeGate On InStand AISCGD1 4-12 CodeGate Off Outof-Stand AOSCGD0 4-12 *CodeGate On Outof-Stand AOSCGD1 4-12 Object Detection Mode Off In-Stand AISOEN0 4-12 Object Detection Mode On Out-ofStand AOSOEN1 4-12 *Object Detection Mode Off Out-ofStand AOSOEN0 4-12 *Object Detection Mode On In-Stand AISOEN1 4-12 Do Not End Object Detection After Good Read In-Stand AISOGD0 4-13 * Indicates default 10 - 23 Selection In-Stand and Out-ofStand Settings (continued) 10 - 24 Setting Serial Command # Indicates a numeric entry Page *End Object Detection After Good Read In-Stand AISOGD1 4-13 Do Not End Object Detection After Good Read Out-ofStand AOSOGD0 4-13 *End Object Detection After Good Read Out-ofStand AOSOGD1 4-13 Object Detection Laser Timeout InStand (Range 1 - 65525) *5000 ms AISODT##### 4-13 Object Detection Laser Timeout Outof-Stand (Range 1 - 65525) *5000 ms AOSODT##### 4-13 *Object Detection Distance - Short InStand AISRNG2 4-14 Object Detection Distance - Long InStand AISRNG1 4-14 Object Detection Distance - Short Out-of-Stand AOSRNG2 4-14 *Object Detection Distance - Long Outof-Stand AOSRNG1 4-14 * Indicates default Selection Character Activation Mode Character Deactivation Mode Reread Delay Setting Serial Command * Indicates default # Indicates a numeric entry Page *Off HSTCEN0 4-14 On HSTCEN1 4-14 Activation Character HSTACH## 4-15 Do Not End Character Activation After Good Read HSTCGD0 4-15 *End Character Activation After Good Read HSTCGD1 4-15 Character Activation Laser Timeout (Range 1 - 65525) *5000 ms HSTCDT##### 4-15 *Off HSTDEN0 4-16 On HSTDEN1 4-16 Deactivation Character HSTDCH## 4-16 Short (500 ms) DLYRRD500 4-17 *Medium (750 ms) DLYRRD750 4-17 Long (1000 ms) DLYRRD1000 4-17 Extra Long (2000 ms) DLYRRD2000 4-17 User-Specified Reread Delay Range 0 - 30,000 ms DLYRRD##### 4-17 Output Sequence Editor Enter Sequence SEQBLK 4-20 Default Sequence SEQDFT 4-20 Sequence Timeout (Range 1 - 65535) *5000 ms SEQDLY##### 4-20 Sequence Match Beeper *On SEQBEP1 4-21 Off SEQBEP0 4-21 Partial Sequence Transmit Partial Sequence SEQTTS1 4-21 *Discard Partial Sequence SEQTTS0 4-21 10 - 25 Setting Serial Command * Indicates default # Indicates a numeric entry Page Required SEQ_EN2 4-22 On/Not Required SEQ_EN1 4-22 *Off SEQ_EN0 4-22 On SHWNRD1 4-22 *Off SHWNRD0 4-22 Add CR Suffix to All Symbologies VSUFCR 5-3 Prefix PREBK2## 5-3 Clear One Prefix PRECL2 5-3 Clear All Prefixes PRECA2 5-3 Add Suffix SUFBK2## 5-4 Clear One Suffix SUFCL2 5-4 Selection Require Output Sequence No Read Prefix/Suffix Selections Suffix Add Prefix Clear All Suffixes SUFCA2 5-4 Transmit Alternate Extended ASCII Characters *Transmit Alternate Extended ASCIi KBDEXT0 5-4 Transmit Normal Extended ASCIi KBDEXT1 5-4 Function Code Transmit *Enable RMVFNC0 5-6 Disable RMVFNC1 5-6 Communication Check Character *None HSTXRC0 5-6 LRC Starts on 1st Character HSTXRC1 5-6 LRC Starts on 2nd Character HSTXRC2 5-6 CRC HSTXRC3 5-6 Intercharacter Delay Range 0 - 1000 (5ms increments) DLYCHR## 5-7 User Specified Intercharacter Delay Delay Length 0 - 1000 (5ms increments) DLYCRX## 5-8 Character to Trigger Delay DLY_XX## 5-8 10 - 26 Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page Interfunction Delay Range 0 - 1000 (5ms increments) DLYFNC## 5-8 Intermessage Delay Range 0 - 1000 (5ms increments) DLYMSG## 5-9 DFMDF3 6-1 Enter Data Format DFMBK3## 6-2 Clear One Data Format DFMCL3 6-3 Clear All Data Formats DFMCA3 6-3 Data Formatter Selections Data Format Editor Data Formatter Data Format NonMatch Error Tone *Default Data Format (None) Data Formatter Off DFM_EN0 6-8 *Data Formatter On, Not Required, Keep Prefix/Suffix DFM_EN1 6-9 Data Format Required, Keep Prefix/Suffix DFM_EN2 6-9 Data Formatter On, Not Required, Drop Prefix/Suffix DFM_EN3 6-9 Data Format Required, Drop Prefix/Suffix DFM_EN4 6-9 *Data Format NonMatch Error Tone On DFMDEC0 6-10 Data Format NonMatch Error Tone Off DFMDEC1 6-10 10 - 27 Selection Primary/Alternate Data Formats Single Scan Data Format Change Setting Serial Command # Indicates a numeric entry Page Primary Data Format ALTFNM0 6-10 Data Format 1 ALTFNM1 6-10 Data Format 2 ALTFNM2 6-10 Data Format 3 ALTFNM3 6-10 Single Scan-Primary Data Format VSAF_0 6-11 Single Scan-Data Format 1 VSAF_1 6-11 Single Scan-Data Format 2 VSAF_2 6-11 Single Scan-Data Format 3 VSAF_3 6-11 All Symbologies Off ALLENA0 7-1 All Symbologies On ALLENA1 7-1 Default All Codabar Settings CBRDFT 7-3 Off CBRENA0 7-3 *On CBRENA1 7-3 *Don’t Transmit CBRSSX0 7-3 Transmit CBRSSX1 7-3 * Indicates default Symbologies All Symbologies Codabar Codabar Start/Stop Char. 10 - 28 Setting Serial Command * Indicates default # Indicates a numeric entry Page *No Check Char. CBRCK20 7-4 Validate Modulo 16, But Don’t Transmit CBRCK21 7-4 Validate Modulo 16, and Transmit CBRCK22 7-4 Validate Modulo 7 CD, But Don’t Transmit CBRCK23 7-4 Validate Modulo 7 CD, and Transmit CBRCK24 7-4 Validate CLSI, But Don’t Transmit CBRCK25 7-4 Validate CLSI, and Transmit CBRCK26 7-4 *Off CBRCCT0 7-5 On CBRCCT1 7-5 Require CBRCCT2 7-5 Concatenation Timeout DLYCCT 7-5 Codabar Redundancy Range (0 - 10) *0 CBRVOT## 7-5 Codabar Message Length Minimum (1 - 80) *3 CBRMIN## 7-6 Maximum (1 - 80) *80 CBRMAX## 7-6 Code 39 Default All Code 39 Settings C39DFT 7-7 Off C39ENA0 7-7 *On C39ENA1 7-7 *Don’t Transmit C39SSX0 7-7 Transmit C39SSX1 7-7 Selection Codabar Check Char. Codabar Concatenation Code 39 Start/Stop Char. 10 - 29 Setting Serial Command * Indicates default # Indicates a numeric entry Page *No Check Char. C39CK20 7-8 Validate, But Don’t Transmit C39CK21 7-8 Validate, and Transmit C39CK22 7-8 Code 39 Redundancy Range (0 - 10) *0 C39VOT## 7-8 Code 39 Message Length Minimum (1 - 80) *3 C39MIN## 7-8 Maximum (1 - 80) *80 C39MAX## 7-8 Code 32 Pharmaceutical (PARAF) *Off C39B320 7-9 On C39B321 7-9 Code 39 Full ASCII *Off C39ASC0 7-10 On C39ASC1 7-10 Default All Interleaved 2 of 5 Settings I25DFT 7-11 Off I25ENA0 7-11 Selection Code 39 Check Char. Interleaved 2 of 5 *On I25ENA1 7-11 Follett Formatting *Off I25FOL0 7-11 On I25FOL1 7-11 NULL Characters *Off I25NUL0 7-11 On I25NUL1 7-11 *No Check Char. I25CK20 7-12 Validate, But Don’t Transmit I25CK21 7-12 Validate, and Transmit I25CK22 7-12 Interleaved 2 of 5 Redundancy Range (0 - 10) *0 I25VOT## 7-12 Interleaved 2 of 5 Message Length Minimum (1 - 80) *6 I25MIN## 7-13 Maximum (1 - 80) *80 I25MAX## 7-13 Interleaved 2 of 5 Check Digit 10 - 30 Setting Serial Command # Indicates a numeric entry Page Default All NEC 2 of 5 Settings N25DFT 7-13 *Off N25ENA0 7-13 On N25ENA1 7-13 *No Check Char. N25CK20 7-14 Validate, But Don’t Transmit N25CK21 7-14 Validate, and Transmit N25CK22 7-14 NEC 2 of 5 Redundancy Range (0 - 10) *0 N25VOT## 7-14 NEC 2 of 5 Message Length Minimum (1 - 80) *3 N25MIN## 7-14 Maximum (1 - 80) *80 N25MAX## 7-14 Code 93 Default All Code 93 Settings C93DFT 7-15 Off C93ENA0 7-15 *On C93ENA1 7-16 Code 93 Redundancy Range (0 - 10) *0 C93VOT## 7-15 Code 93 Message Length Minimum (1 - 80) *3 C93MIN## 7-16 Maximum (1 - 80) *80 C93MAX## 7-16 Straight 2 of 5 Industrial Default All Straight 2 of 5 Industrial Settings R25DFT 7-16 *Off R25ENA0 7-16 On R25ENA1 7-16 Straight 2 of 5 Industrial Redundancy Range (0 - 10) *0 R25VOT## 7-17 Straight 2 of 5 Industrial Message Length Minimum (3 - 80) *3 R25MIN## 7-17 Maximum (3 - 80) *80 R25MAX## 7-17 Selection NEC 2 of 5 NEC 2 of 5 Check Digit * Indicates default 10 - 31 Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page Straight 2 of 5 IATA Default All Straight 2 of 5 IATA Settings A25DFT 7-18 Straight 2 of 5 IATA *Off A25ENA0 7-18 On A25ENA1 7-18 Straight 2 of 5 IATA Redundancy Range (0 - 10) *0 A25VOT## 7-18 Straight 2 of 5 IATA Message Length Minimum (1 - 80) *13 A25MIN## 7-19 Maximum (1 - 80) *15 A25MAX## 7-19 Default All Matrix 2 of 5 Settings X25DFT 7-19 *Off X25ENA0 7-19 Matrix 2 of 5 On X25ENA1 7-19 Matrix 2 of 5 Redundancy Range (0 - 10) *0 X25VOT## 7-20 Matrix 2 of 5 Message Length Minimum (1 - 80) *3 X25MIN## 7-20 Maximum (1 - 80) *80 X25MAX## 7-20 Matrix 2 of 5 Check Char. *No Check Char. X25CK20 7-20 Validate, But Don’t Transmit X25CK21 7-20 Validate and Transmit X25CK22 7-20 Default All Code 11 Settings C11DFT 7-21 *Off C11ENA0 7-21 On C11ENA1 7-21 Code 11 10 - 32 Setting Serial Command # Indicates a numeric entry Page 1 Check Digit Required C11CK20 7-21 *2 Check Digits Required C11CK21 7-21 Auto Select Check Digits Required C11CK22 7-21 Validate and Transmit One Check Digit C11CK23 7-22 Validate and Transmit Two Check Digits C11CK24 7-22 Validate and Transmit Auto Select Check Digits C11CK25 7-22 Code 11 Redundancy Range (0 - 10) *0 C11VOT## 7-22 Code 11 Message Length Minimum (1 - 80) *3 C11MIN## 7-23 Maximum (1 - 80) *80 C11MAX## 7-23 Code 128 Default All Code 128 Settings 128DFT 7-24 Off 128ENA0 7-24 Selection Code 11 Check Digits Required Check Digit Validation * Indicates default *On 128ENA1 7-24 128 Group Separator Output *Off 128GSE0 7-24 On 128GSE1 7-24 Code 128 Redundancy Range (0 - 10) *0 128VOT## 7-25 Code 128 Message Length Minimum (1 - 80) *3 128MIN## 7-25 Maximum (1 - 80) *80 128MAX## 7-25 ISBT 128 *Off ISBENA0 7-25 On ISBENA1 7-25 Concatenation Timeout DLYCCT 7-26 10 - 33 Selection ISBT128 Predefined Concatenation Sequences ISBT 128 Predefined Concatenation Sequences On/Off 10 - 34 Setting Serial Command # Indicates a numeric entry Page * Donation ID Number (001) and ABO/RhD Blood Groups (002) ISBPCS0 7-26 Donation ID Number (001) and Donor ID Number (019) ISBPCS1 7-26 Donation ID Number (001) and Confidential Unit Exclusion Status ISBPCS2 7-26 Product Code (003) and Expiration Date (Form 1) ISBPCS3 7-26 Product Code (003) and Expiration Date (Form 2) ISBPCS4 7-26 Product Code (003) and Expiration Date (Form 3) ISBPCS5 7-26 Product Code (003) and Expiration Date (Form 4) ISBPCS6 7-26 *Off ISBPCE0 7-27 Allow Predefined Sequence ISBPCE1 7-27 Require Predefined Sequence ISBPCE2 7-27 * Indicates default Setting Serial Command # Indicates a numeric entry Page 1st Left Identifier (0255) *0 ISBUL1## 7-28 2nd Left Identifier (0255) *0 ISBUL2## 7-28 1st Right Identifier (0-255) *0 ISBUR1## 7-28 2nd Right Identifier (0-255) *0 ISBUR2## 7-28 ISBT 128 UserDefined Concatenation Sequences On/Off *Off ISBUCE0 7-29 Allow User-Defined Sequence ISBUCE1 7-29 Require UserDefined Sequence ISBUCE2 7-29 Content Verification *Off ISBXM00 7-29 On ISBXM01 7-29 Transmit Identifiers Off ISBXM10 7-30 *On ISBXM11 7-30 Flag Conversion *Off ISBXM20 7-30 On ISBXM21 7-30 GS1-128 Default All GS1-128 Settings GS1DFT 7-31 *On GS1ENA1 7-31 Off GS1ENA0 7-31 *Off GS1EMU0 7-31 Transmit Without Identifiers GS1EMU1 7-31 Transmit With Identifiers GS1EMU2 7-31 GS1-128 Redundancy Range (0 - 10) *0 GS1VOT## 7-32 GS1-128 Message Length Minimum (1 - 80) *3 GS1MIN 7-32 Maximum (0 - 80) *80 GS1MAX 7-32 Selection ISBT 128 UserDefined Concatenation Sequences GS1-128 Application Identifier Parsing * Indicates default 10 - 35 Setting Serial Command # Indicates a numeric entry Page TELDFT 7-33 *Off TELENA0 7-33 On TELENA1 7-33 *AIM Telepen Output TELOLD0 7-33 Original Telepen Output TELOLD1 7-33 Telepen Redundancy Range (0 - 10) *0 TELVOT## 7-34 Telepen Message Length Minimum (1 - 80) *3 TELMIN## 7-34 Maximum (1 - 80) *80 TELMAX## 7-34 UPC-A Default All UPC-A Settings UPADFT 7-35 Off UPAENA0 7-36 *On UPAENA1 7-36 UPC-A Number System Off UPANSX0 7-35 *On UPANSX1 7-35 UPC-A Check Digit Off UPACKX0 7-35 *On UPACKX1 7-36 Selection Telepen Telepen Output * Indicates default Default All Telepen Settings UPC-A 2 Digit Addenda *Off UPAAD20 7-36 On UPAAD21 7-36 UPC-A 5 Digit Addenda *Off UPAAD50 7-36 On UPAAD51 7-36 UPC-A Addenda Required *Not Required UPAARQ0 7-36 Required UPAARQ1 7-36 Addenda Timeout Range (0 - 65535) *100 DLYADD##### 7-37 UPC-A Addenda Separator *Off UPAADS0 7-37 On UPAADS1 7-37 UPC-A Redundancy Range (0 - 10) *0 UPAVOT## 7-37 10 - 36 Setting Serial Command * Indicates default # Indicates a numeric entry Page UPC-A/EAN-13 with Extended Coupon Code *Off CPNENA0 7-38 Allow Concatenation CPNENA1 7-38 Require Concatenation CPNENA2 7-38 UPC-A Number System 4 Addenda Required * Don’t Require Coupon Code ARQSY40 7-39 Require Coupon Code ARQSY41 7-39 UPC-A Number System 5 Addenda Required * Don’t Require Coupon Code/ Addenda ARQSY50 7-40 Require 2 Digit Addenda ARQSY51 7-40 Require 5 Digit Addenda ARQSY52 7-40 Require 2 or 5 Digit Addenda ARQSY53 7-40 Require Coupon Code ARQSY54 7-40 Require Coupon Code or 2 Digit Addenda ARQSY55 7-40 Require Coupon Code or 5 Digit Addenda ARQSY56 7-40 Require Coupon Code, 2 Digit Addenda, or 5 Digit Addenda ARQSY57 7-40 Addenda Timeout Range (0 - 65535) *100 DLYADD##### 7-41 UPC-E0 Default All UPC-E Settings UPEDFT 7-41 Off UPEEN00 7-41 *On UPEEN01 7-41 Selection 10 - 37 Selection UPC-E0 Expand Setting Serial Command * Indicates default # Indicates a numeric entry Page *Off UPEEXP0 7-41 On UPEEXP1 7-41 UPC-E0 Number System *On UPEEXN1 7-42 Off UPEEXN0 7-42 UPC-E0 Check Digit *Off UPECKX0 7-42 On UPECKX1 7-42 UPC-E0 Leading Zero *Off UPENSX0 7-43 On UPENSX1 7-43 UPC-E0 Addenda 2 Digit Addenda On UPEAD21 7-43 *2 Digit Addenda Off UPEAD20 7-43 5 Digit Addenda On UPEAD51 7-43 *5 Digit Addenda Off UPEAD50 7-43 UPC-E0 Addenda Required Required UPEARQ1 7-43 *Not Required UPEARQ0 7-43 Addenda Timeout Range (0 - 65535) *100 DLYADD##### 7-44 UPC-E0 Addenda Separator On UPEADS1 7-44 *Off UPEADS0 7-44 UPC-E0 Redundancy Range (0 - 10) *1 UPEVOT## 7-44 EAN/JAN-13 Default All EAN/ JAN Settings E13DFT 7-45 Off E13ENA0 7-45 *On E13ENA1 7-45 EAN/JAN-13 Check Digit Off E13CKX0 7-45 *On E13CKX1 7-45 EAN/JAN-13 2 Digit Addenda 2 Digit Addenda On E13AD21 7-46 *2 Digit Addenda Off E13AD20 7-46 5 Digit Addenda On E13AD51 7-46 *5 Digit Addenda Off E13AD50 7-46 *Not Required E13ARQ0 7-46 Required E13ARQ1 7-46 EAN/JAN-13 Addenda Required 10 - 38 Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page EAN-13 Beginning with 2 Addenda Required * Don’t Require 2 Digit Addenda ARQSY20 7-47 Require 2 Digit Addenda ARQSY21 7-47 EAN-13 Beginning with 290 Addenda Required * Don’t Require 5 Digit Addenda ARQ2900 7-47 Require 5 Digit Addenda ARQ2901 7-47 EAN-13 Beginning with 378/379 Addenda Required * Don’t Require Addenda ARQ3780 7-48 Require 2 Digit Addenda ARQ3781 7-48 Require 5 Digit Addenda ARQ3782 7-48 Require 2 or 5 Digit Addenda ARQ3783 7-48 * Don’t Require Addenda ARQ4140 7-49 Require 2 Digit Addenda ARQ4141 7-49 Require 5 Digit Addenda ARQ4142 7-49 Require 2 or 5 Digit Addenda ARQ4143 7-49 * Don’t Require Addenda ARQ4340 7-50 Require 2 Digit Addenda ARQ4341 7-50 Require 5 Digit Addenda ARQ4342 7-50 Require 2 or 5 Digit Addenda ARQ4343 7-50 EAN-13 Beginning with 414/419 Addenda Required EAN-13 Beginning with 434/439 Addenda Required 10 - 39 Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page EAN-13 Beginning with 977 Addenda Required * Don’t Require 2 Digit Addenda ARQ9770 7-50 Require 2 Digit Addenda ARQ9771 7-50 EAN-13 Beginning with 978 Addenda Required * Don’t Require 5 Digit Addenda ARQ9780 7-51 Require 5 Digit Addenda ARQ9781 7-51 EAN-13 Beginning with 979 Addenda Required * Don’t Require 5 Digit Addenda ARQ9790 7-51 Require 5 Digit Addenda ARQ9791 7-51 Addenda Timeout Range (0 - 65535) *100 DLYADD##### 7-52 EAN/JAN-13 Addenda Separator *Off E13ADS0 7-52 On E13ADS1 7-53 EAN/JAN-13 Redundancy Range (0 - 10) *0 E13VOT## 7-52 ISBN Translate *Off E13ISB0 7-53 On E13ISB1 7-53 Convert to 13-Digit On E13I131 7-53 *Convert to 13-Digit Off E13I130 7-53 Reformat On E13IBR1 7-53 *Reformat Off E13IBR0 7-53 *Off E13ISS0 7-54 On E13ISS1 7-54 Reformat On E13ISR1 7-54 *Reformat Off E13ISR0 7-54 ISSN Translate 10 - 40 Setting Serial Command # Indicates a numeric entry Page Default All EAN/ JAN 8 Settings EA8DFT 7-55 Off EA8ENA0 7-55 *On EA8ENA1 7-55 Off EA8CKX0 7-55 *On EA8CKX1 7-55 *2 Digit Addenda Off EA8AD20 7-56 2 Digit Addenda On EA8AD21 7-56 *5 Digit Addenda Off EA8AD50 7-56 5 Digit Addenda On EA8AD51 7-56 EAN/JAN-8 Addenda Required *Not Required EA8ARQ0 7-56 Required EA8ARQ1 7-56 Addenda Timeout Range (0 - 65535) *100 DLYADD##### 7-57 EAN/JAN-8 Addenda Separator *Off EA8ADS0 7-57 On EA8ADS1 7-57 EAN/JAN-8 Redundancy Range (0 - 10) *0 EA8VOT## 7-57 MSI Default All MSI Settings MSIDFT 7-58 *Off MSIENA0 7-58 On MSIENA1 7-58 Selection EAN/JAN-8 EAN/JAN-8 Check Digit EAN/JAN-8 Addenda * Indicates default 10 - 41 Setting Serial Command # Indicates a numeric entry Page *Validate Type 10, but Don’t Transmit MSICHK0 7-59 Validate Type 10 and Transmit MSICHK1 7-59 Validate 2 Type 10 Chars, but Don’t Transmit MSICHK2 7-59 Validate 2 Type 10 Chars and Transmit MSICHK3 7-59 Validate Type 10 then Type 11 Char, but Don’t Transmit MSICHK4 7-59 Validate Type 10 then Type 11 Char and Transmit MSICHK5 7-59 Disable MSI Check Characters MSICHK6 7-59 MSI Redundancy Range (0 - 10) *0 MSIVOT## 7-59 MSI Message Length Minimum (1 - 80) *3 MSIMIN## 7-60 Maximum (1 - 80) *80 MSIMAX## 7-60 Default All Plessey Code Settings PLSDFT 7-60 Off PLSENA0 7-60 *On PLSENA1 7-60 *No Check Char. PLSCHK0 7-61 Validate, But Don’t Transmit PLSCHK1 7-61 Validate, and Transmit PLSCHK2 7-61 Selection MSI Check Character Plessey Code Plessey Check Char. * Indicates default Plessey Redundancy Range (0 - 10) *0 PLSVOT## 7-61 Plessey Message Length Minimum (1 - 80) *3 PLSMIN## 7-61 Maximum (1 - 80) *80 PLSMAX## 7-61 10 - 42 Selection GS1 DataBar Omnidirectional Setting Serial Command # Indicates a numeric entry Page Default All GS1 DataBar Omnidirectional Settings RSSDFT 7-62 Off RSSENA0 7-62 * Indicates default *On RSSENA1 7-62 GS1 DataBar Omnidirectional Redundancy Range (0 - 10) *0 RSSVOT## 7-62 GS1 DataBar Limited Default All GS1 DataBar Limited Settings RSLDFT 7-63 Off RSLENA0 7-63 *On RSLENA1 7-63 GS1 DataBar Limited Redundancy Range (0 - 10) *0 RSLVOT## 7-63 GS1 DataBar Expanded Default All GS1 DataBar Expanded Settings RSEDFT 7-64 Off RSEENA0 7-64 *On RSEENA1 7-64 GS1 DataBar Expanded Redundancy Range (0 - 10) *0 RSEVOT## 7-64 GS1 DataBar Expanded Msg. Length Minimum (1 - 80) *3 RSEMIN## 7-65 Maximum (1 - 80) *80 RSEMAX## 7-65 Trioptic Code *Off TRIENA0 7-65 On TRIENA1 7-65 10 - 43 Setting Serial Command * Indicates default # Indicates a numeric entry Page GS1-128 Emulation EANEMU1 7-66 GS1 DataBar Emulation EANEMU2 7-66 GS1 Code Expansion Off EANEMU3 7-66 EAN8 to EAN13 Conversion EANEMU4 7-66 *GS1 Emulation Off EANEMU0 7-66 Default All China Post (Hong Kong 2 of 5) Settings CPCDFT 7-66 *Off CPCENA0 7-67 On CPCENA1 7-67 China Post (Hong Kong 2 of 5) Redundancy Range (0 - 10) *0 CPCVOT## 7-67 China Post (Hong Kong 2 of 5) Msg. Length Minimum (1 - 80) *3 CPCMIN## 7-67 Maximum (1 - 80) *80 CPCMAX## 7-67 TRGSTO#### 10-4 Selection GS1 Emulation Postal Codes China Post (Hong Kong 2 of 5) Serial Trigger Commands Read Time-Out 10 - 44 0 - 300,000 *30,000 ms 11 Product Specifications Voyager 1200g Scanner Product Specifications Parameter Specification Mechanical Height 3.8 in. (97mm) Length 7.1 in. (180mm) Width 2.6 in. (66mm) Weight 4.41 oz. (125g) Electrical Input Voltage 5V + 5% Operating Power 700mW; 140 mA (typical) @ 5V Standby Power 350mW; 70 mA (typical) @ 5V Environmental Operating Temperature 32°F to 122°F (0°C to 50°C) Storage Temperature -4°F to 140°F (-20°C to 60°C) Humidity 0 to 95% non-condensing Drop Operational after 30 drops to concrete from 5 ft. (1.5m) Environmental Sealing IP42 Light Levels 0 - 70,000 lux (direct sunlight) ESD 16kV, 9kV contact Scan Performance Scan Pattern Single scan line Scan Angle Horizontal: 30° Scan Speed 100 scan lines per second Print Contrast 10% minimum reflectance difference Pitch, Skew 60°, 60° Decode Capabilities Reads standard 1D and GS1 DataBar symbologies DOF with 3.5 mil resolution at standard range Typical Performance 5 mil Code 39 27 - 151mm (1.1 - 5.9 in.) 7.5 mil Code 39 16 - 216mm (.6 - 8.5 in.) 10.4 mil Code 39 0 - 277mm (0 - 10.9 in.) 13 mil UPC-A 0 - 311mm (0 - 12.2 in.) 20 mil Code 39 0 - 367mm (0 - 14.4 in.) 11 - 1 Parameter Specification Guaranteed Performance 5 mil Code 39 38 - 132mm (1.5 - 5.2 in.) 7.5 mil Code 39 26 - 189mm (1 - 7.4 in.) 10.4 mil Code 39 0 - 229mm (0 - 9 in.) 13 mil UPC-A 0 - 253mm (0 - 10 in.) 20 mil Code 39 0 - 293mm (0 - 11.5 in.) Laser Beam Wavelength 645 - 660 nm Divergence < 1.5 mrad. per IEC 60825-1 worst case Maximum Power Output < 1 mw Embedded Laser Wavelength 645 - 660 nm Divergence < 1.5 mrad. per IEC 60825-1 worst case Maximum Power Output 10 mw 11 - 2 Voyager 1202g Scanner Product Specifications Parameter Specification Mechanical Height 3.6 in. (92mm) Length 7.1 in. (180mm) Width 2.6 in. (65mm) Weight (with battery) 6.3 oz. (178.6g) Battery Lithium Ion 1800 mAHr minimum Number of Scans Up to 45,000 per charge Expected Hours of Operation 12 Expected Charge Time 4 hours (external supply) 8 hours (USB power) Radio Frequency 2.4 to 2.5 GHz (ISM Band) Frequency Hopping Bluetooth v.2.1 Range 33 ft. (10 m) typical line of sight Data Rate Up to 3 MBps Environmental Temperature Ranges: Operating - Charging 32° F to +113° F (0° C to 45° C) Operating - Non-Charging 32° F to +122° F (0° C to 50° C) Storage* 23°F to +95°F (-5°C to 35°C) Humidity Up to 95% non-condensing Mechanical Drop Operational after 30 drops from 5 feet (1.5m) to concrete Environmental Sealing IP42 ESD Sensitivity 16kV air 9kV contact Scan Performance Pitch, Skew 60°, 60° 11 - 3 Parameter Specification Scan Pattern Single scan line Scan Angle Horizontal: 30° Scan Speed 100 scan lines per second Print Contrast 10% minimum reflectance difference Decode Capabilities Reads standard 1D and GS1 DataBar symbologies DOF with 3.5 mil resolution at standard range Typical Performance 5 mil Code 39 27 - 151mm (1.1 - 5.9 in.) 7.5 mil Code 39 16 - 216mm (.6 - 8.5 in.) 1.40 mil Code 39 0 - 277mm (0 - 10.9 in.) 13 mil UPC-A 0 - 311mm (0 - 12.2 in.) 20 mil Code 39 0 - 367mm (0 - 14.4 in.) Guaranteed Performance 5 mil Code 39 38 - 132mm (1.5 - 5.2 in.) 7.5 mil Code 39 26 - 189mm (1 - 7.4 in.) 10.4 mil Code 39 0 - 229mm (0 - 9 in.) 13 mil UPC-A 0 - 253mm (0 - 10 in.) 20 mil Code 39 0 - 293mm (0 - 11.5 in.) Laser Beam Wavelength 645 - 660 nm Divergence < 1.5 mrad. per IEC 60825-1 worst case Maximum Power Output < 1 mw Embedded Laser Wavelength 645 - 660 nm Divergence < 1.5 mrad. per IEC 60825-1 worst case Maximum Power Output 10 mw CCB00-010BT Charge Base Product Specifications Parameter Specification Mechanical Dimensions (Typical): Height 3.8 inches (98mm) Length 7.9 inches (200mm) Width 2.6 inches (67mm) 11 - 4 Weight 6.5 oz (185g) Electrical Input Voltage 5 volts +5% Operating Power - Charging 5W (1A@5V) (external supply) 2.5W (0.5A@5V) (USB power) Non-Charging Power 0.5W (1A@5V) Expected Charge Time 4 hours (external supply) 8 hours (USB power) Radio Frequency 2.4 to 2.5 GHz (ISM Band) Frequency Hopping Bluetooth v.2.1 Range 33 ft. (10 m) typical (line of sight) Data Rate Up to 3 MBps Temperature Ranges: Operating - Charging 32° F to +113° F (0° C to 45° C) Operating - Non-Charging 32° F to +122° F (0° C to 50° C) Storage* 23°F to +95°F (-5°C to 35°C) Humidity Up to 95% non-condensing Environmental Mechanical Drop Operational after 30 drops from 3.28 feet (1m) to concrete ESD Sensitivity 16kV air 9kV contact 11 - 5 CCB00-010BT Charge Base Mounting 3.07 in (78mm) Use 2 M3x15mm PHP, self-tapping wood screws 11 - 6 Cable shield Cable select Supply ground Terminal data Terminal clock Keyboard clock Supply power input +5V power Keyboard data Note: Pin assignments are not compatible with Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty. 10 connects to the base 10 Pin RJ41 Modular Plug Standard Cable Pinouts Keyboard Wedge 11 - 7 11 - 8 Cable shield Cable select Supply ground Transmit data Receive data - serial data to scanner CTS +5V power RTS Note: Pin assignments are not compatible with Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty. 10 connects to the base 10 Pin RJ41 Modular Plug Standard Cable Pinouts Serial Output +5V power Transmit Enable Cable shield Cable select Supply ground Transmit data Receive data - serial data to scanner Note: RS485 signal conversion is performed in the cable. Pin assignments are not compatible with Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty. 10 connects to the base 10 Pin RJ41 Modular Plug Standard Cable Pinouts RS485 Output 11 - 9 11 - 10 Data + Data - +5V power Cable shield Cable select Supply ground Note: Pin assignments are not compatible with Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty. connects to the base 10 Pin Modular Plug 10 Standard Cable Pinouts USB 12 Maintenance Repairs Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center (see Customer Support on page 13-1). Maintenance Your device provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the following periodic checks ensure dependable operation: Cleaning the Device Reading performance may degrade if the scanner’s window is not clean. If the window is visibly dirty, or if the scanner isn’t operating well, clean the window with a soft cloth or lens tissue dampened with water (or a mild detergent- water solution). If a detergent solution is used, rinse with a clean lens tissue dampened with water only. The scanner and base’s housing may also be cleaned the same way. Caution: Do not submerge the scanner in water. The scanner’s housing is not watertight. Do not use abrasive wipes or tissues on the scanner’s window – abrasive wipes may scratch the window. Never use solvents (e.g., alcohol or acetone) on the housing or window – solvents may damage the finish or the window. Inspecting Cords and Connectors Inspect the interface cable and connector for wear or other signs of damage. A badly worn cable or damaged connector may interfere with scanner operation. Contact your distributor for information about cable replacement. Cable replacement instructions are on page 12-1. Replacing Cables in Corded Scanners The standard interface cable is attached to the scanner with an 10-pin modular connector. When properly seated, the connector is held in the scanner’s handle by a flexible retention tab. The interface cable is designed to be field replaceable. 12 - 1 • Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable. Replacing an Interface Cable in a Corded Scanner 1. Turn the power to the host system OFF. 2. Disconnect the scanner’s cable from the terminal or computer. 3. Locate the small hole on the underside of the scanner’s handle. This is the cable release. 4. Straighten one end of a paper clip. 5. Insert the end of the paper clip into the small hole and press in. This depresses the retention tab, releasing the connector. Pull the connector out while maintaining pressure on the paper clip, then remove the paper clip. Cable Release 6. Replace with the new cable. Insert the connector into the opening and press firmly. The connector is keyed to go in only one way, and will click into place. Replacing Cables in Cordless Systems Replacing an Interface Cable in a Base 1. Turn the power to the host system OFF. 2. Disconnect the base’s cable from the terminal or computer. 12 - 2 3. Turn the base upside down. 4. Locate the pinhole for the cable release and insert a straightened paper clip. 5. Pull the connector out while maintaining pressure on the connector release clip. 6. Replace with the new cable. Insert the connector into the opening and press firmly. The connector is keyed to go in only one way, and will click into place. Troubleshooting a Voyager Scanner The scanner automatically performs self-tests whenever you turn it on. If your scanner is not functioning properly, review the following Troubleshooting Guide to try to isolate the problem. Is the power on? Is the laser aimer on? If the laser aimer isn’t illuminated, check that: • The cable is connected properly. • The host system power is on (if external power isn’t used). • The button works. Is the scanner having trouble reading your symbols? If the scanner isn’t reading symbols well, check that the scanner window is clean and that the symbols: • Aren’t smeared, rough, scratched, or exhibiting voids. • Aren’t coated with frost or water droplets on the surface. • Are enabled in the scanner or in the decoder to which the scanner connects. 12 - 3 Is the bar code displayed but not entered? The bar code is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or the Tab key, for example). • You need to program a suffix. Programming a suffix enables the scanner to output the bar code data plus the key you need (such as “CR”) to enter the data into your application. Refer to Prefix/Suffix Overview on page 5-1 for further information. Does the scanner read the bar code incorrectly? If the scanner reads a bar code, but the data is not displayed correctly on the host screen: • The scanner may not be programmed for the appropriate terminal interface. For example, you scan “12345” and the host displays “@es%.” Reprogram the scanner with the correct Plug and Play bar code. See Programming the Interface beginning on page 2-1. • The scanner may not be programmed to output your bar code data properly. For example, you scan “12345” and the host displays “A12345B.” Reprogram the scanner with the proper symbology selections. See Chapter 7. The scanner won’t read your bar code at all. 1. Scan the sample bar codes in the back of this manual. If the scanner reads the sample bar codes, check that your bar code is readable. Verify that your bar code symbology is enabled (see Chapter 7). 2. If the scanner still can’t read the sample bar codes, scan All Symbologies On, page 7-1. The cordless scanner won’t scan bar codes while it is in the base cradle 1. Scanning While in Cradle Off may be programmed. 2. Scan the * Scanning in Cradle On (page 3-8) bar code so the scanner will also scan bar codes while in the base cradle. If you aren’t sure what programming options have been set in the scanner, or if you want the factory default settings restored, refer to Setting Custom Defaults on page 1-9. Troubleshooting a Cordless System Troubleshooting a Base Note: Visit the Services and Support section of our website (www.honeywellaidc.com) to check for the latest software for both the scanner and the base. 12 - 4 If your base is not functioning properly, review the following troubleshooting guidelines to try to isolate the problem. Is the red LED on? If the red LED isn’t illuminated, check that: • The power cable is connected properly and there is power at the power source. • The host system power is on (if external power isn’t used). Is the green LED on? If the green LED isn’t illuminated, check that: • The scanner is correctly placed in the base. • There is external power or 12 volt host power. • Charge mode is turned on. (See "Flash Updates" on page 3-6) • The battery is not bad or deeply discharged. In some cases, the scanner’s battery may trickle charge to bring it into an acceptable level and then transition to a normal charge cycle. Troubleshooting a Cordless Scanner Note: Make sure that your scanner’s battery is charged. Visit the Services and Support section of our website (www.honeywellaidc.com) to check for the latest software for both the scanner and the base or Access Point. Is the scanner having trouble reading your symbols? If the scanner isn’t reading symbols well, check that the symbols: • Aren’t smeared, rough, scratched, or exhibiting voids. • Aren’t coated with frost or water droplets on the surface. • Are enabled in the base or Access Point to which the scanner connects. Is the bar code displayed but not entered into the application? The bar code is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or the Tab key, for example). • You need to program a suffix. Programming a suffix enables the scanner to output the bar code data plus the key you need (such as “CR”) to enter the data into your application. Refer to Prefix/Suffix Overview on page 51 for further information. Does the scanner read the bar code incorrectly? If the scanner reads a bar code, but the data is not displayed correctly on the host screen: • The base or Access Point may not be programmed for the appropriate terminal interface. For example, you scan “12345” and the host displays “@es%.” Reprogram the base/Access Point with the correct Plug and Play bar code. See Programming the Interface beginning on page 2-1. 12 - 5 • The bas or Access Pointe may not be programmed to output your bar code data properly. For example, you scan “12345” and the host displays “A12345B.” Reprogram the base/Access Point with the proper symbology selections. See Chapter 7. The scanner won’t read your bar code at all. • Scan the sample bar codes in the back of this manual. If the scanner reads the sample bar codes, check that your bar code is readable. Verify that your bar code symbology is enabled (see Chapter 7). If the scanner still can’t read the sample bar codes, scan All Symbologies on page 7-1. 12 - 6 13 Customer Support Technical Assistance If you need assistance installing or troubleshooting your device, please call your distributor or the nearest technical support office: North America/Canada Telephone: (800) 782-4263 E-mail: hsmnasupport@honeywell.com Latin America Telephone: (803) 835-8000 Telephone: (800) 782-4263 E-mail: hsmlasupport@honeywell.com Brazil Telephone: +55 (11) 5185-8222 Fax: +55 (11) 5185-8225 E-mail: brsuporte@honeywell.com Mexico Telephone: 01-800-HONEYWELL (01-800-466-3993) E-mail: soporte.hsm@honeywell.com Europe, Middle East, and Africa Telephone: +31 (0) 40 7999 393 Fax: +31 (0) 40 2425 672 E-mail: hsmeurosupport@honeywell.com Hong Kong Telephone: +852-29536436 Fax: +852-2511-3557 E-mail: aptechsupport@honeywell.com Singapore Telephone: +65-6842-7155 Fax: +65-6842-7166 E-mail: aptechsupport@honeywell.com China Telephone: +86 800 828 2803 Fax: +86-512-6762-2560 E-mail: aptechsupport@honeywell.com Japan Telephone: +81-3-6730-7344 Fax: +81-3-6730-7222 E-mail: aptechsupport@honeywell.com 13 - 1 Online Technical Assistance You can also access technical assistance online at www.honeywellaidc.com. Product Service and Repair Honeywell International Inc. provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning the product. North America Telephone: (800) 782-4263 E-mail: hsmnaservice@honeywell.com Latin America Telephone: (803) 835-8000 Telephone: (800) 782-4263 Fax: (239) 263-9689 E-mail: laservice@honeywell.com Brazil Telephone: +55 (11) 5185-8222 Fax: +55 (11) 5185-8225 E-mail: brservice@honeywell.com Mexico Telephone: 01-800-HONEYWELL (01-800-466-3993) Fax: +52 (55) 5531-3672 E-mail: mxservice@honeywell.com Europe, Middle East, and Africa Telephone: +31 (0) 40 2901 633 Fax: +31 (0) 40 2901 631 E-mail: euroservice@honeywell.com Hong Kong Telephone: +852-29536436 Fax: +852-2511-3557 E-mail: apservice@honeywell.com Singapore Telephone: +65-6842-7155 Fax: +65-6842-7166 E-mail: apservice@honeywell.com China Telephone: +86 800 828 2803 Fax: +86-512-6762-2560 E-mail: apservice@honeywell.com 13 - 2 Japan Telephone: +81-3-6730-7344 Fax: +81-3-6730-7222 E-mail: apservice@honeywell.com Online Product Service and Repair Assistance You can also access product service and repair assistance online at www.honeywellaidc.com. Limited Warranty Honeywell International Inc. (“HII”) warrants its products to be free from defects in materials and workmanship and to conform to HII’s published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any HII product which is (i) improperly installed or used; (ii) damaged by accident or negligence, including failure to follow the proper maintenance, service, and cleaning schedule; or (iii) damaged as a result of (A) modification or alteration by the purchaser or other party, (B) excessive voltage or current supplied to or drawn from the interface connections, (C) static electricity or electro-static discharge, (D) operation under conditions beyond the specified operating parameters, or (E) repair or service of the product by anyone other than HII or its authorized representatives. This warranty shall extend from the time of shipment for the duration published by HII for the product at the time of purchase (“Warranty Period”). Any defective product must be returned (at purchaser’s expense) during the Warranty Period to HII factory or authorized service center for inspection. No product will be accepted by HII without a Return Materials Authorization, which may be obtained by contacting HII. In the event that the product is returned to HII or its authorized service center within the Warranty Period and HII determines to its satisfaction that the product is defective due to defects in materials or workmanship, HII, at its sole option, will either repair or replace the product without charge, except for return shipping to HII. EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR WRITTEN, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT. HII’S RESPONSIBILITY AND PURCHASER’S EXCLUSIVE REMEDY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT WITH NEW OR REFURBISHED PARTS. IN NO EVENT SHALL HII BE LIABLE FOR INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, AND, IN NO EVENT, SHALL ANY LIABILITY OF HII ARISING IN CONNECTION WITH ANY PRODUCT SOLD HEREUNDER (WHETHER SUCH LIABILITY ARISES FROM A CLAIM BASED ON CONTRACT, WARRANTY, TORT, OR OTHERWISE) EXCEED THE ACTUAL AMOUNT PAID TO HII FOR THE PRODUCT. THESE LIMITATIONS ON LIA- 13 - 3 BILITY SHALL REMAIN IN FULL FORCE AND EFFECT EVEN WHEN HII MAY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES, LOSSES, OR DAMAGES. SOME STATES, PROVINCES, OR COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. All provisions of this Limited Warranty are separate and severable, which means that if any provision is held invalid and unenforceable, such determination shall not affect the validity of enforceability of the other provisions hereof. Use of any peripherals not provided by the manufacturer may result in damage not covered by this warranty. This includes but is not limited to: cables, power supplies, cradles, and docking stations. HII extends these warranties only to the first end-users of the products. These warranties are non-transferable. The duration of the limited warranty for the Voyager 1200g scanner is five (5) years. The duration of the limited warranty for the Voyager 1202g scanner and CCB00010BT Charge Base is three (3) years. The duration of the limited warranty for the Voyager battery is one (1) year. 13 - 4 A Reference Charts Symbology Chart Note: Not all symbologies may be supported by your device. Symbology AIM ID Possible AIM ID Modifiers ( m) All Symbologies Code ID (hex) (0x99) Australian Post ]X0 Aztec Code ]zm British Post ]X0 B (0x42) Canadian Post ]X0 C (0x43) China Post ]X0 Q (0x51) Chinese Sensible Code (Han Xin Code) ]X0 H (0x48) Codabar ]Fm 0-1 a (0x61) Codablock A ]O6 0, 1, 4, 5, 6 V (0x56) Codablock F ]Om 0, 1, 4, 5, 6 q (0x71) Code 11 ]H3 Code 128 ]Cm GS1-128 A (0x41) 0-9, A-C z (0x7A) h (0x68) 0, 1, 2, 4 j (0x6A) ]C1 I (0x49) Code 32 Pharmaceutical (PARAF) ]X0 < (0x3C) Code 39 (supports Full ASCII mode) ]Am 0, 1, 3, 4, 5, 7 Code 49 ]Tm 0, 1, 2, 4 l (0x6C) Code 93 and 93i ]Gm 0-9, A-Z, a-m i (0x69) Data Matrix ]dm 0-6 w (0x77) EAN-13 (including Bookland EAN) b (0x62) ]E0 d (0x64) EAN-13 with Add-On ]E3 d (0x64) EAN-13 with Extended Coupon Code ]E3 d (0x64) A-1 Possible AIM ID Modifiers ( m) Code ID (hex) Symbology AIM ID EAN-8 ]E4 D (0x44) ]E3 D (0x44) EAN-8 with Add-On GS1 Composite ]em 0-3 y (0x79) GS1 DataBar ]em y (0x79) GS1 DataBar Limited ]em { (0x7B) GS1 DataBar Omnidirectional ]em y (0x79) GS1 DataBar Expanded ]em } (0x7D) InfoMail ]X0 , (0x2c) Intelligent Mail Bar Code ]X0 M (0x4D) Interleaved 2 of 5 ]Im 0, 1, 3 e (0x65) Japanese Post ]X0 J (0x4A) KIX (Netherlands) Post ]X0 K (0x4B) Korea Post ]X0 ? (0x3F) Matrix 2 of 5 ]X0 m (0x6D) MaxiCode ]Um 0-3 x (0x7 8) MicroPDF417 ]Lm 3-5 R (0x52) MSI ]Mm g (0x67) NEC 2 of 5 ]X0 Y (0x59) OCR MICR (E 13 B) ]o3 O (0x4F) OCR SEMI Font ]o3 O (0x4F) OCR-A ]o1 O (0x4F) OCR-B ]o2 O (0x4F) PDF417 ]Lm Planet Code ]X0 L (0x4C) Postal-4i ]X0 N (0x4E) Postnet ]X0 P (0x50) QR Code and Micro QR Code ]Qm 0-6 s (0x73) Straight 2 of 5 IATA ]Rm 0, 1, 3 f (0x66) A-2 0-2 (0x72) Possible AIM ID Modifiers (m) Code ID (hex) Symbology AIM ID Straight 2 of 5 Industrial ]S0 f (0x66) TCIF Linked Code 39 (TLC39) ]L2 T (0x54) Telepen ]Bm t (0x54) UPC-A ]E0 c (0x63) UPC-A with Add-On ]E3 c (0x63) UPC-A with Extended Coupon Code ]E3 c (0x63) ]E0 E (0x45) UPC-E with Add-On ]E3 E (0x45) UPC-E1 ]X0 E (0x45) UPC-E Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for AIM modifier character details. Prefix/Suffix entries for specific symbologies override the universal (All Symbologies, 99) entry. Refer to Data Editing beginning on page 5-1 and Data Formatting beginning on page 6-1 for information about using Code ID and AIM ID. A-3 ASCII Conversion Chart (Code Page 1252) Note: This table applies to U.S. style keyboards. Certain characters may differ depending on your Country Code/PC regional settings. Non-Printable Characters DEC HEX Character (Code) DEC HEX Character (Code) 16 17 10 11 DATA LINK ESCAPE (DLE) DEVICE CONTROL 1 (DC1) 18 19 20 12 13 14 DEVICE CONTROL 2 (DC2) DEVICE CONTROL 3 (DC3) DEVICE CONTROL 4 (DC4) NULL START OF HEADING (SOH) START OF TEXT (STX) END OF TEXT (ETX) END OF TRANSMISSION (EOT) END OF QUERY (ENQ) 21 15 ACKNOWLEDGE (ACK) BEEP (BEL) 22 23 16 17 10 11 12 BACKSPACE (BS) HORIZONTAL TAB (HT) LINE FEED (LF) VERTICAL TAB (VT) FF (FORM FEED) 24 25 26 27 28 18 19 1A 1B 1C 13 CR (CARRIAGE RETURN) 29 1D 14 SO (SHIFT OUT) 30 1E 15 SI (SHIFT IN) 31 1F NEGATIVE ACKNOWLEDGEMENT (NAK) SYNCHRONIZE (SYN) END OF TRANSMISSION BLOCK (ETB) CANCEL (CAN) END OF MEDIUM (EM) SUBSTITUTE (SUB) ESCAPE (ESC) FILE SEPARATOR (FS) RIGHT ARROW GROUP SEPARATOR (GS) LEFT ARROW RECORD SEPARATOR (RS) UP ARROW UNIT SEPARATOR (US) DOWN ARROW Printable Characters DEC HEX 32 33 34 35 36 37 38 39 20 21 22 23 24 25 26 27 A-4 Character DEC HEX 64 65 66 67 68 69 70 71 40 41 42 43 44 45 46 47 Character DEC 96 97 98 99 100 101 102 103 HEX 60 61 62 63 64 65 66 67 Character Printable Characters (Continued) DEC HEX 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F Character DEC HEX 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F Character DEC HEX Character 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F Extended ASCII Characters DEC HEX 128 129 130 131 132 133 134 135 136 137 138 139 80 81 82 83 84 85 86 87 88 89 8A 8B Character €€ ‚ ƒ „ … † ‡ ˆ ‰ Š ‹ DEC HEX 171 172 173 174 175 176 177 178 179 180 181 182 AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 Character « ¬ ® ¯ ° ± ² ³ ´ µ ¶ DEC HEX 214 215 216 217 218 219 220 221 222 223 224 225 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 Character Ö × Ø Ù Ú Û Ü Ý Þ ß à á A-5 Extended ASCII Characters (Continued) DEC HEX 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA Character Œ Ž ‘ ’ “ ” • – — ˜ ™ š › œ ž Ÿ ¡ ¢ £ ¤ ¥ ¦ § ¨ © ª DEC HEX 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 B7 B8 B9 BA BB BC BD BE BF C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 Character · ¸ ¹ º » ¼ ½ ¾ ¿ À Á Â Ã Ä Å Æ Ç È É Ê Ë Ì Í Î Ï Ð Ñ Ò Ó Ô Õ DEC HEX 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 Character E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF â ã ä å æ ç è é ê ë ì í î ï ð ñ ò ó ô õ ö ÷ ø ù ú û ü ý þ ÿ Code Page Mapping of Printed Barcodes Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the barcode being scanned was created using a code page that is different from A-6 the one the host program is expecting. If this is the case, select the code page with which the barcodes were created. The data characters should then appear properly. Note: The Code Page option is available for Code 39, Code 93, and Code 128. Code Page Standard Description CP ISO646 2 (Default) ISO 2022 CP Binary 51 ISO 8859 1 51 Western European Replacement Characters 82 ISO 2022 11 Swe Swedish Replacement Characters 83 ISO 2022 69 Fra French/Belgium Replacement Characters 81 ISO 2022 25 Fra French/Belgium Replacement Characters Automatic National Replacement Characters 84 ISO 2022 11 Ger German Replacement Characters 85 ISO 2022 11 Ita Italian Replacement Characters 86 ISO 2022 11 Swi Swiss Replacement Characters 87 ISO 2022 11 UK British Replacement Characters 88 ISO 2022 11 Dan Danish Replacement Characters 89 ISO 2022 11 Nor Norwegian Replacement Characters 90 ISO 2022 11 Spa Spanish Replacement Characters 91 ISO 2022 85 Spanish Replacement Characters 92 ISO 2022 16 Portuguese Replacement Characters 93 ISO 2022 84 Portuguese Replacement Characters 94 ISO 2022 60 Norwegian Replacement Characters A-7 A-8 Sample Symbols UPC-A 0 123456 7890 Code 128 Code 128 Code 39 BC321 Code 93 123456-9$ Interleaved 2 of 5 1234567890 EAN-13 9 780330 290951 Codabar A13579B Straight 2 of 5 Industrial 123456 Sample Symbols Matrix 2 of 5 6543210 GS1 DataBar (01)00123456789012 Programming Chart Programming Chart Save Discard Reset Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again. Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 ft 15 VG1200-UG Rev (b) 10/11
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Author : Honeywell Scanning & Mobility Create Date : 2011:09:15 10:16:43Z Keywords : Honeywell, Voyager 1200g, Voyager 1202g Modify Date : 2011:09:15 11:22:17-04:00 Subject : User’s Guide for Voyager 1200g and 2102g XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Creator Tool : FrameMaker 9.0 Metadata Date : 2011:09:15 11:22:17-04:00 Format : application/pdf Title : Voyager 1200g/1202g User’s Guide Creator : Honeywell Scanning & Mobility Description : User’s Guide for Voyager 1200g and 2102g Producer : Acrobat Distiller 9.4.5 (Windows) Document ID : uuid:3ac2f2fa-2c0c-4ad7-ab8b-b380759b5e5d Instance ID : uuid:e7687f02-28fe-4fc6-be7d-547a83fe1180 Page Mode : UseOutlines Page Count : 288EXIF Metadata provided by EXIF.tools