Honeywell Ct2095 Users Manual 69 1385 Honeywell/20 Programmable Thermostat

CT2095 to the manual 8653ec9b-26a1-4c6e-9e57-38a2edaabf99

2015-01-23

: Honeywell Honeywell-Ct2095-Users-Manual-262029 honeywell-ct2095-users-manual-262029 honeywell pdf

Open the PDF directly: View PDF .
Page Count: 40

Download
Open PDF In Browser	View PDF

Honeywell/20
Programmable Thermostat
OWNER’S GUIDE
Weekday/Weekend (5-day/2-day)
Programmable Heat and/or Cool
Low Voltage (20 to 30 Vac)
Thermostat and Mounting Plate
Model CT2095

Place Bar Code Here
69- 1385

Welcome to the world of comfort and energy
savings with your new Honeywell
Programmable Thermostat.

MERCURY NOTICE

If this thermostat is replacing a thermostat that contains mercury in a sealed
tube, do not place your old thermostat in
the trash. Dispose of properly.

Your new thermostat will automatically control
the temperature in your home, keeping you
comfortable while saving energy when
programmed according to the instructions in
this manual.

Contact your local waste management
authority for instructions regarding recycling and the proper disposal of your old
thermostat. If you have questions, call
Honeywell Customer Response Center
at 1-800468-1502.

Direct any questions concerning the application
of this thermostat to Honeywell Consumer
Services at 1-800-468-1502, Monday-Friday,
7:00 a.m.-5:30 p.m., Central time.

MERCURY
SWITCH

Typical location of
a mercury switch
in a thermostat.
M3701

69-1385

Contents
Step 1. Prepare for Installation .....................................................................................................
Step 2. Remove Old Thermostat ..................................................................................................
Step 3. Install Batteries ................................................................................................................
Step 4. Program Thermostat ........................................................................................................
Step 5. Adjust Fan Operation Switch, As Required ......................................................................
Step 6. Adjust System On-Time, °F/°C, As Required ...................................................................
Step 7. Mount Thermostat Mounting Plate ...................................................................................
Step 8. Wire Thermostat Terminals ..............................................................................................
Step 9. Mount Thermostat ............................................................................................................
Step 10. Check Thermostat Operation After Programming and Installing ...................................
Step 11. Set Fan and System Switches .......................................................................................
Troubleshooting Guide .................................................................................................................
Limited One-Year Warranty ..........................................................................................................

4
6
8
11
19
19
21
23
27
28
30
31
35

69-1385

Step 1. Prepare for Installation
❑ Check Table 1 to make sure this thermostat is compatible with your system. If not, return it to the
retailer. For more information, call Honeywell Consumer Services, 1-800-468-1502, Monday Friday, 7 am to 5:30 pm, Central time.

Gas—Standing Pilot
Gas—Electronic Ignition
Gas-Fired Boilers
Gas—Millivolt

Table 1. Compatibility Information.
System Type
Compatible with CT2095
Yes
Yes
Yesa,b
No

Oil-Fired Boilers
Yesa,b
Oil-Fired Furnace
Yes
Electric Furnace
Yes
Electric Air Conditioning
Yes
Baseboard Electric (120/240 Line Volt)
No
Heat Pumps/Multistage Equipment
No
Not compatible with any 120/240 volt circuit.
a
Compatible with Honeywell 2-wire zone valves. Isolating relay required for 3-wire thermostats for zone valves.
Not compatible with 2-wire White-Rodgers no. 1361 valves.
b Compatible with hot water baseboard systems. Does not work efficiently on steam or gravity systems.
4
69-1385

❑ Acquire tools and items as needed (see illustration). Also purchase two AA alkaline batteries; we
recommend Energizer® batteries.

CROSS-RECESSED
SCREWDRIVER
HAND OR
POWER DRILL
WITH 3/16 INCH
DRILL BIT, IF NEEDED
TO DRILL HOLES
IN WALL
WIRE CUTTER/STRIPPER OR SHARP
KNIFE, IF NEEDED TO STRIP WIRES

LEVEL, IF NEEDED TO LEVEL
THERMOSTAT FOR APPEARANCE

M13544

69-1385

Step 2. Remove Old Thermostat

❑ Loosen screws holding thermostat to
subbase, wallplate or wall, and lift away.
❑ Disconnect wires from old thermostat or
subbase. As you disconnect each wire,
attach one of the enclosed labels to each old
terminal designation. If there are only two
wires, they do not need labeling. If there is
an extra wire that is not connected to your
old thermostat, you also do not connect it to
your new thermostat. Keep the wires from
falling back into the wall by wrapping them
around a pencil as shown.

❑ Test to be sure your heating and cooling
systems are working properly. If either does
not work, contact your local heating/air
conditioning dealer. To avoid compressor
damage, do not operate the cooling system
when outdoor temperature is below 50°F
(10°C).
❑ Turn off power to the system at the furnace,
or at the fuse/circuit breaker panel.
❑ Carefully unpack your new thermostat and
mounting plate, saving package of screws,
instructions and receipt.
❑ Remove cover from old thermostat. If it does
not snap off when pulled firmly from the
bottom, check for a screw used to lock on
the cover.

WIRES THROUGH
WALL OPENING

M5136

69-1385

Replacing a Clock Thermostat that has
C or C1 Clock Terminals?

those systems so return the product to the
retailer. If you want information about the
programmable thermostats that work with your
system, call Honeywell Consumer Services at
1-800-468-1502.

If you are replacing a Honeywell Chronotherm®
Thermostat, you may find one or two wires that
go to the C or C1 clock terminals on the
Chronotherm® Thermostat wiring wallplate. Do
not allow them to touch, or you can damage
your transformer. Disconnect the wires and
wrap them separately, using electrical tape. Do
not wrap them together. Place the wires where
they do not interfere with the operation of the
new thermostat. Record the colors and terminal
designation labels of the remaining wires.

Three thermostat wires?
If you have three wires for heating only and can
operate the fan using the fan On switch, this
thermostat works with your system. However,
some hot water (zoned) heating systems have
three thermostat wires. The thermostat does
not work without installing an isolating relay on
these systems. For details, call Honeywell
Consumer Services at 1-800-468-1502.

Six or more wires?
If there are six or more wires (excluding clock
wires attached to terminals), you probably have
a variation of a heat pump or multistage
system. This thermostat is not compatible with
7

69-1385

Step 3. Install Batteries
IMPORTANT
Batteries must be installed for the programming and operation of the thermostat and heating/cooling system.
❑ Purchase two AA alkaline batteries; nonalkaline batteries do not last as long, and
can leak, causing damage to the thermostat
or the wall surface. We recommend
Energizer® batteries.
❑ Open the top cover of thermostat to access
control panel and battery compartment.
❑ Make sure the thermostat is set to the Off
position.
❑ Use a coin to remove the battery cover.

BATTERY
DOOR COVER

REMOVING
BATTERY
DOOR
M12492

69-1385

❑ Install the fresh batteries as shown, making
sure positive and negative terminals are
oriented correctly.
❑ Replace the battery cover.

After the batteries are completely dead, the
bAtLo indication disappears, leaving a
completely blank display.

As the batteries run low, a bAt Lo indicator
flashes for one to two months before the
batteries run out completely. Replace the
batteries as soon as possible after the indicator
starts flashing. If you do not replace the
batteries sometime during the flashing bAt Lo,
the indicator eventually stops flashing. bAt Lo
then stays on without flashing, indicating the
thermostat and heating/cooling system have
stopped working and the batteries are almost
completely dead.

INSTALL TWO AA ALKALINE
BATTERIES AS SHOWN

M1713

69-1385

IMPORTANT
Although the thermostat has a low battery indicator, replace the batteries
once a year to prevent the thermostat
and heating/cooling system from shutting down due to lack of battery power.

Press down on the left ends of batteries to
remove them. If you insert the new batteries
within 20 to 30 seconds of removing the old
ones, you do not need to reprogram the
thermostat. However, if the display is blank, the
batteries are dead or incorrectly installed and
you must reprogram. See Step 4.

As a precaution, when leaving home
for longer than a month, change batteries before you leave to prevent the
system from shutting down due to lack
of battery power.

69-1385

Step 4. Program Thermostat

• WAKE is the time period you want the house
at a comfortable temperature when you get
up and while you get ready for work or
school. (This is a higher temperature during
heating season and a lower temperature during cooling season.)
• LEAVE is the time period you can set for an
energy-saving temperature while you are
away at work or school. (This is a lower temperature during heating season and a higher
temperature during cooling season.)
• RETURN is the time period you want the
house at a comfortable temperature for activities before bedtime. (This is a higher temperature during heating season and a lower
temperature during cooling season.)
• SLEEP is the time period you can set for an
energy-saving temperature while you are
sleeping. (This is a lower temperature during
the heating season and a higher temperature during the cooling season.)

After the batteries are installed, the thermostat
can be easily programmed in your hand before
it is installed on the wall.
If you prefer to program the thermostat after it is
installed on the wall, go to Step 7 and return
later to this programming section.
The Personal Programming Chart, Tables 2 and
3, may be helpful for planning your program
schedule of time and temperature settings for
various times of the day.
Four time periods are available during
weekdays — WAKE, LEAVE, RETURN, and
SLEEP; view these periods individually on the
display as you press the Weekday key.

69-1385

Set one schedule for weekdays and another for
weekends because your requirements are
usually different for each. Also, during weekends, only the WAKE and SLEEP time periods
are available.

If no program is entered for the weekends, the
thermostat operates on the weekday SLEEP
program all weekend.
Before programming, remove the clear plastic
overlay covering the display.

Fill in the times and temperatures you desire for
weekdays and weekends. If you decide not to
program the thermostat, it automatically controls heating at 68°F (20°C), and cooling at 78°F
(26°C), 24 hours a day. Also, you do not need to
enter a time and temperature program for all
periods if your schedule does not require it. For
example, a house that is occupied during weekdays would require programs only for WAKE
and SLEEP.

When pressing the keys, use the ball of your
finger or a soft pencil eraser. Using sharp fingernails or pencil points can damage the keypad.
If you make an error at any time during programming, just press the Run Program key, and
continue again at the previous step in your
sequence.

69-1385

Table 2. Personal Programming Chart for Heating.
Days of Week

Heating Program Start Time

Heating Temperaturea

Weekdays
WAKE
LEAVE
RETURN
SLEEP
Weekendsb
WAKE
SLEEP
a
b

The temperatures cannot be set any higher than 88°F (31°C) or any lower than 45°F (7°C).
If you decide not to enter weekend programs, the thermostat operates on the weekday SLEEP program all weekend.
13

69-1385

Table 3. Personal Programming Chart for Cooling.
Days of Week

Cooling Program Start Time

Cooling Temperaturea

Weekdays
WAKE
LEAVE
RETURN
SLEEP
Weekendsb
WAKE
SLEEP
a
b

69-1385

NOTE: Batteries are required for operation and programming. When inserting batteries, set the
System switch to Off. Remove the battery door (on the thermostat left side) using a coin at
the bottom. Follow instructions in Step 3. Also see the label inside the battery cover for
abbreviated programming procedures for your thermostat.

Set Current Time/Day

Time
Clock/Day

To set time, press and release

once, press

until current shows. To set day, press and

Time
Clock/Day

release

Run Program

again, press

until current day shows; then press

Heating Program

Weekday

With System switch at Heat, press and release
SET appear on display.

once. WAKE, MON FRI (Monday-Friday), and

TEMP

Time

Use

to program WAKE time and

to program WAKE temperature for MON FRI (Monday-Friday).

Repeat sequence for LEAVE, RETURN, SLEEP.
15

69-1385

Time
Weekend

Press

until SAT SUN (Saturday-Sunday), WAKE and SET appear on display. Use

to program

TEMP

WAKE time and

to program WAKE temperature for SAT SUN (Saturday-Sunday).
Run Program

Repeat sequence for SLEEP. Press and release

to start the program.

Cooling Program
With System switch at Cool, follow the same instructions as for the Heating Program.
Run Program

After programming, adjust the Fan and System switches, as desired. Press and release
start the program.

69-1385

Operating Your Thermostat
System switch must be set to Heat or Cool to perform the following:
TEMP

Temporarily Change Temperature for current period only — Press

; temporary indicator shows
Run Program

on display and cancels itself at the next scheduled change; to cancel sooner, press

.
TEMP

Hold Temp

Hold a Temperature Indefinitely (such as when on vacation) — Press

and

; HOLD

Run Program

appears on display; to cancel, press

.
Present Set

Check Current Temperature Setting — Press
Weekday

Check Programs — Press
Run Program
.

Weekend

repeatedly to see each time and temperature; then press

69-1385

Weekday

Cancel Program — Press

Clear

Weekend

until program to cancel shows; then press

Usage

Check Usage — Press

to see length of time heat or air conditioning has run today since
Clear

midnight; press again for yesterday’s usage, press again for cumulative; press

to clear

Run Program

cumulative reading, if desired; then press

Permanently Change a Program — Repeat Heating Program or Cooling Program steps, as
applicable.
Run Program

Return to Normal Program or Start Program — Press

69-1385

Step 5. Adjust Fan Operation
Switch, As Required

as a guide. The system on-time should be
optimized according to the type of system to
maximize comfort. Setting the screw “out one
turn” means turning the screw approximately
360° counterclockwise, or about one complete turn.

❑ The thermostat fan operation switch, labeled
FUEL SWITCH (see illustration) is factory-set
in the F position. This is the correct setting for
most systems. If your system is an electric
heat system, set the switch to E to allow the
fan to turn on immediately with the heating in
a system when the G terminal is connected.

THERMOSTAT BACK

DISPLAY °F C–IN
DISPLAY °C C–OUT
1 TURN

Step 6. Adjust System On-Time,
°F/°C, As Required

ADJUST SCREWS THROUGH HOLES
TO SELECT OPERATION DESIRED
FUEL SWITCH
HEATING SYSTEM
POSITION
F
WARM AIR A–IN
B–IN
FURNACE
F
HOT WATER A–OUT B–IN
BOILER
1 TURN
E
ELECTRIC A–IN
B–OUT
FURNACE
1 TURN

FOR HIGH EFFICIENCY FURNACE (90%+ AFUE)
ADJUST: SCREW A–OUT ONE TURN
SCREW B–IN
FUEL SWITCH – F POSITION

❑ The thermostat on-time is factory-set for a
warm air, gas or oil heating system. If you are
installing it on another type of system, adjust
the on-time accordingly by setting screws A
and B on the back of the thermostat. Use the
heating system table shown in the illustration

FUEL SWITCH

M8796A

69-1385

IMPORTANT
When using a high efficiency furnace
such as a 90 percent or greater Average Fuel Utilization Efficiency (AFUE)
unit, adjust screw A out one turn and
leave screw B in.

In the unlikely event that you want a longer
furnace on-time, readjust screws A and/or B as
follows:
First, turn both screws in completely, then
adjust for system type:
• Warm Air Furnace—Set at the Hot Water
setting (A—out one turn, B—leave in).
• Electric Furnace—Leave at the Warm Air
Furnace setting (A—leave in, B—leave in).

❑ The thermostat is set to read the temperature
in degrees Fahrenheit. If readings are
desired in degrees Celsius, adjust screw C
out one turn.

NOTE: This thermostat does not have a setting for steam/gravity air; cycles would
not be long enough for accurate temperature control.

69-1385

Step 7. Mount Thermostat
Mounting Plate

WALL ANCHORS (2)
WIRES THROUGH
WALL OPENING

❑ Position mounting plate on wall. Use level to
make sure mounting plate is level. Use a
pencil to mark the two mounting holes.
❑ Remove mounting plate from wall, and drill
3/16-inch holes in wall (if drywall) as marked.
For firmer material such as plaster or wood,
drill 7/32-inch holes. Gently tap anchors
(provided) into drilled holes until flush with the
wall.
❑ Reposition mounting plate over holes,
pulling wires through wiring opening.
❑ Loosely insert two mounting screws into
holes.

WALL

MOUNTING
PLATE

MOUNTING
SCREWS (2)

M1718

69-1385

❑ Level for appearance only; thermostat
functions properly even when not level.
❑ Tighten mounting screws.

LEVEL

M1714A

69-1385

Step 8. Wire Thermostat Terminals
NOTE: All wiring must comply with local codes
and ordinances. If unsure about household wiring procedures, call your local
heating/air conditioning contractor.

METHOD TO INCREASE WIRE LENGTH

❑ Refer to the labels you placed on the terminal
wires when you removed your old thermostat.
Match the letter of your old thermostat wire
with the terminal of the corresponding letter
on the back of your new thermostat. (See
wiring diagrams.) Hold the thermostat as
shown in illustration to minimize need for wire
extenders. If wires are still too short, use wire
connectors (purchased locally) to extend
wires. See illustration for guidelines on using
wire extenders.

WIRE NUT SIZE FOR
TWO 18-GAUGE WIRES

WIRE
FROM
WALL

6 IN. (152 MM)
OF 18-GAUGE
THERMOSTAT
WIRE. MATCH
INSULATION
COLORS
OR MARK
WIRE ENDS.

M1715A

❑ In 5-wire installations only, be sure to remove
the factory-installed jumper connecting terminals R and Rc.

69-1385

❑ Loosen the terminal screws and slip each wire beneath its matching terminal. See illustrations for
wire insertion technique.
❑ Securely tighten terminals.
❑ Plug the hole in the wall with insulation to help prevent drafts from adversely affecting thermostat
operation.

END OF WIRE
VISIBLE HERE

JUMPER (FACTORYINSTALLED). REMOVE
IF 5-WIRE SYSTEM
R

5/16 in.
(8 mm)
STRIP

INSERT
STRAIGHT
UNDER
SCREW HEAD

M1712B

M3002A

69-1385

2-WIRE HEAT-ONLY (JUMPER INTACT)

4-WIRE HEAT/COOL (JUMPER INTACT)

JUMPER

HEATING
RELAY OR
VALVE COIL

L1
(HOT)

HEATING
RELAY OR
VALVE COIL

COOLING
CONTACTOR
COIL

L2
1

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED.

FAN
RELAY
M1709B

L1
(HOT)
L2

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED.
M1710B

69-1385

5-WIRE HEAT/COOL (JUMPER REMOVED)
A

3-WIRE COOL-ONLY (JUMPER INTACT)
A

G
W

JUMPER
R

Rc
R

HEATING
RELAY OR
VALVE COIL

FAN
RELAY

COOLING
CONTACTOR
COIL

FAN
RELAY

L1
(HOT)

L1
(HOT)
L2

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED.
M1711C

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED.
M848A

69-1385

Step 9. Mount Thermostat
NOTE: To remove thermostat from wall, first pull out at bottom of thermostat, then remove top.
A. ENGAGE TABS AT TOP OF
THERMOSTAT AND SUBBASE.

B. PRESS LOWER EDGE
OF CASE TO LATCH.

C. SWING OPEN COVER TO
CHECK OPERATION.

AM
TU
LEAVE

Clock/Day

Time

TEMP

Run Progra

Weekday
Hold Temp
Weekend

Fan
Auto

Clear

Usage

On
Cool

Present Set

System
Off Heat

M13545

69-1385

Step 10. Check Thermostat
Operation After Programming
and Installing

Move the System switch to
Heat and the Fan switch to
Auto.

Cool

Off

Heat

M1703

Auto

M1705

Heating

TEMP

Press TEMP key until the setting is about 10°F (6°C) above
room temperature. Heating
should start and the fan should
run after a short delay (immediately if fan operation switch is set to E position).

Do not check heating system operation by
jumpering thermostat terminals such as gas
valve, zone valve, and oil burner control at the
primary control. This damages the thermostat.
Instead, jumper R and W wires at the
thermostat.

Press TEMP key until setting is about 10°F (6°C)
below room temperature. The heating equipment should shut off.

69-1385

Cooling

Move the System switch to
Cool and the Fan switch to
Auto.

To avoid possible compressor damage, do not
operate the cooling system when outdoor
temperature is below 50°F (10°C). See
compressor manufacturer instructions.

Cool

Off

Heat

M1704

Auto

M1705

IMPORTANT
When cooling setting is changed, thermostat delays up to five minutes
before turning on the air conditioner.
This delay protects the compressor.

TEMP

Press TEMP key until setting is
about 10°F (6°C) below room
temperature. The cooling
equipment and fan should start.

Press TEMP key until the setting is about 10°F
(6°C) above room temperature. The cooling
equipment and fan should stop.
Move the System switch to Off;
keep the Fan switch at Auto.
The system and fan should be
off.

Cool

Off

Heat

M1707

Auto

69-1385

Step 11. Set Fan and System Switches
First set the Fan switch.
Fan Auto: Normal setting for most
Auto
On
homes. A single-speed fan will
turn on automatically with the air
conditioner or furnace. A two-speed fan
usually runs on high with the air conditioner
and on low with the furnace.

Then set the System switch.
Cool: The thermostat controls
your air conditioning
system.
Off: Both the heating and air
conditioning systems are
off.

Fan On: The fan runs continuously. Auto On
Use for improved air circulation
during special occasions or for
more efficient electronic air
cleaning. (In a heat-only system, fan runs
continuously only if fan relay is connected to
the thermostat.)

Heat: The thermostat
controls your heating
system.

Cool

Off

Heat

Cool

Off

Heat

Cool

Off

Heat

69-1385

Troubleshooting Guide
If...

Then...

Display does not come on.

Set the System switch to Off. Remove batteries. Insert them backward
for at least five seconds to reset the thermostat. Replace batteries
correctly. Display should come on.
Make sure batteries are fresh and installed correctly.
You have reached the temperature setting limit. The setting range is
45°F to 88°F (7° to 31°C).

Temperature display does
not go lower than 45°F
(7°C) or higher than 88°F
(31°C) during programming.
Temperature change occurs Check the program times for the questionable period. Be sure that AM
at wrong times.
and PM indications are correct. Make sure the current day and time
are correct. Reprogram, if necessary.

69-1385

If...

Then...

Heating does not come on. Check that the System switch is set to Heat.
Make sure the heating setpoint is above the room temperature.
Check the system fuse or circuit breaker and replace or reset, if
necessary.
Make sure the System switch is in the On position; set it to On if it is in
the Off position.
If temperature setting is higher than the current temperature and the
display says HEAT, contact Honeywell Consumer Services at 1-800468-1502.
Cooling does not come on. Check that the System switch is set to Cool.
Make sure the cooling setpoint is below the room temperature.
Check the system fuse or circuit breaker and replace or reset, if
necessary.
Make sure the System switch at the air conditioner is in the On
position; set it to On if it is in the Off position.

69-1385

If...
Cooling does not come on
(Continued).

The house is too warm or
too cool.
SYSTEM ON indicator is
lighted, but no heat is
coming from the registers.

Then...
The thermostat has a built-in time delay on cooling. Allow five to ten
minutes after changing the setting before the air conditioner starts.
If temperature setting is lower than current temperature, and the
display says COOL, move the System switch from Cool to Off for ten
minutes. After ten minutes, return the switch to the Cool position. If air
conditioner comes on, compressor may have reached its high-limit
temperature protection and shut down.If air conditioner does not come
on after the ten minutes and the display says COOL, contact
Honeywell Consumer Services at 1-800-468-1502.
If two- or four-wire installation, verify R-Rc jumper is installed.
Press Present Set key to check the current temperature setting.
If desired, change the temperature setting. See Cooling Program
section.
Allow time for the furnace to heat up and the fan to come on before
checking for heat at the register. (Check to make sure system on-time
is set correctly. See Step 6.)

69-1385

Toll-free Customer Assistance
For all questions concerning this thermostat, please read and follow the instructions. If additional
assistance is needed, call Honeywell Consumer Services at 1-800-468-1502, Monday - Friday,
7:00 a.m. - 5:30 p.m. Central time.
Before you call, please have the following information available—thermostat model number and
date code, type of heating/cooling system (hot water, warm air, oil, gas, etc.), and number of wires
connected to the thermostat.
NOTICE
This equipment is a Class B digital apparatus, which complies with Canadian Radio Interference
Regulations, CRC c.1374.

69-1385

Limited One-Year Warranty
Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and
service, for a period of one (1) year from the date of purchase by the consumer. If, at any time during the warranty period, the
product is defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option) within a reasonable period of time.
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the retailer from which you purchased it, or
(ii) package it carefully, along with proof of purchase (including date of purchase) and a short description of the malfunction, and
mail it, postage prepaid, to the following address:
Honeywell Inc.
Canada: Honeywell Limited/Honeywell Limitée
Return Goods Department
Product ServicesON15-FFE
1050 Berkshire Lane
740 Ellesmere Road
Plymouth, MN 55441-4437
Scarborough, Ontario M1P 2V9
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the
defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer.
Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT
BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY
OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so this limitation may not apply to you.

69-1385

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF
ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, IS HEREBY LIMITED TO THE ONE YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations
on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
If you have any questions concerning this warranty, please write our Customer Assistance Center, Honeywell Inc., P.O. Box 524,
Minneapolis, MN 55440-0524 or call 1-800-468-1502, Monday-Friday, 7:00 a.m. to 5:30 p.m., Central time. In Canada, write
Retail Products ON15-02H, Honeywell Limited/Honeywell Limitée, 155 Gordon Baker Road, North York, Ontario M2H 2C9.

69-1385

TYPICAL ENERGY SAVINGS FOR REPRESENTATIVE CITIES IN THE U.S. AND CANADA
Savings for Once-A-Day
10°F (5°C) decrease

Savings for Twice-A-Day
10°F (5°C) decrease*

Savings for 5°F (3°)
summer increase

Approximate percentage of energy cost savings

30%
28%
26%
24%
22%
20%
18%
16%
14%
12%
10%
8%
6%
4%
2%

Minneapolis
St. Paul
Montreal
Ottawa
Toronto

Edmonton
Regina
Winnipeg

Calgary
Moncton
North Bay
Quebec
St. John's

Halifax

Vancouver

Buffalo
Cleveland
Milwaukee

Denver
Des Moines
Omaha
Salt Lake
City

Boston
Chicago
Detroit
Pittsburgh
Indianapolis

Cincinnati
Kansas City
St. Louis
Columbus

Louisville
New York
Philadelphia Portland
Wash., D C
Seattle

San
Francisco

Dallas
Atlanta

Los Angeles

*Based on 10°F (5°C) decrease—(5°F [3°C] decrease
gives approximately 55 percent of these savings).

San Diego

M2416A

69-1385

Home and Building Control
Honeywell Inc.
Honeywell Plaza
P.O. Box 524
Minneapolis, MN 55408-0524
69-1385

G.H.

6-00

Home and Building Control
Honeywell Limited-Honeywell Limitée
155 Gordon Baker Road
North York, Ontario
M2H 3N7
Printed in U.S.A. on recycled
paper containing at least 10%
post-consumer paper fibers.

www.honeywell.com/yourhome

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Copy, Extract, Assemble, Print high-res
Page Mode                       : UseOutlines
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2000:06:26 10:11:01Z
Creator Tool                    : FrameMaker 5.5.6p145
Modify Date                     : 2007:05:07 15:49:26-05:00
Metadata Date                   : 2007:05:07 15:49:26-05:00
Format                          : application/pdf
Description                     : Owner's Guide
Creator                         : H&BC Technical Communications
Title                           : 69-1385 - Honeywell/20 Programmable Thermostat
Producer                        : Acrobat Distiller 4.0 for Windows
Document ID                     : uuid:51a894bc-c2f0-462a-9103-46f02865e32c
Instance ID                     : uuid:370717aa-0930-4c8a-8e9f-9547af3f90d8
Page Count                      : 40
Subject                         : Owner's Guide
Author                          : H&BC Technical Communications

EXIF Metadata provided by EXIF.tools

Honeywell Ct2095 Users Manual 69 1385 Honeywell/20 Programmable Thermostat

CT2095 to the manual 8653ec9b-26a1-4c6e-9e57-38a2edaabf99

Navigation menu

Versions of this User Manual:

Views

Navigation