Honeywell Ct2095 Users Manual 69 1385 Honeywell/20 Programmable Thermostat

CT2095 to the manual 8653ec9b-26a1-4c6e-9e57-38a2edaabf99

: Honeywell Honeywell-Ct2095-Users-Manual-262029 honeywell-ct2095-users-manual-262029 honeywell pdf

Open the PDF directly: View PDF .
Page Count: 40

Place Bar Code Here

69- 1385

OWNER’S GUIDE

Honeywell/20

Programmable Thermostat

Weekday/Weekend (5-day/2-day)

Programmable Heat and/or Cool

Low Voltage (20 to 30 Vac)

Thermostat and Mounting Plate

Model CT2095

2 69-1385

Welcome to the world of comfort and energy

savings with your new Honeywell

Programmable Thermostat.

Your new thermostat will automatically control

the temperature in your home, keeping you

comfortable while saving energy when

programmed according to the instructions in

this manual.

Direct any questions concerning the application

of this thermostat to Honeywell Consumer

Services at 1-800-468-1502, Monday-Friday,

7:00 a.m.-5:30 p.m., Central time.

MERCURY NOTICE

If this thermostat is replacing a thermo-

stat that contains mercury in a sealed

tube, do not place your old thermostat in

the trash. Dispose of properly.

Contact your local waste management

authority for instructions regarding recy-

cling and the proper disposal of your old

thermostat. If you have questions, call

Honeywell Customer Response Center

at 1-800-

468-1502.

Typical location of

a mercury switch

in a thermostat.

M3701

MERCURY

SWITCH

3 69-1385

Contents

Step 1. Prepare for Installation ..................................................................................................... 4

Step 2. Remove Old Thermostat ..................................................................................................6

Step 3. Install Batteries ................................................................................................................ 8

Step 4. Program Thermostat ........................................................................................................ 11

Step 5. Adjust Fan Operation Switch, As Required ...................................................................... 19

Step 6. Adjust System On-Time, °F/°C, As Required ................................................................... 19

Step 7. Mount Thermostat Mounting Plate ................................................................................... 21

Step 8. Wire Thermostat Terminals ..............................................................................................23

Step 9. Mount Thermostat ............................................................................................................ 27

Step 10. Check Thermostat Operation After Programming and Installing ................................... 28

Step 11. Set Fan and System Switches ....................................................................................... 30

Troubleshooting Guide ................................................................................................................. 31

Limited One-Year Warranty .......................................................................................................... 35

4 69-1385

Step 1. Prepare for Installation

❑Check Table 1 to make sure this thermostat is compatible with your system. If not, return it to the

retailer. For more information, call Honeywell Consumer Services, 1-800-468-1502, Monday -

Friday, 7 am to 5:30 pm, Central time.

Not compatible with any 120/240 volt circuit.

aCompatible with Honeywell 2-wire zone valves. Isolating relay required for 3-wire thermostats for zone valves.

Not compatible with 2-wire White-Rodgers no. 1361 valves.

bCompatible with hot water baseboard systems. Does not work efficiently on steam or gravity systems.

Table 1. Compatibility Information.

System Type Compatible with CT2095

Gas—Standing Pilot Yes

Gas—Electronic Ignition Yes

Gas-Fired Boilers Yesa,b

Gas—Millivolt No

Oil-Fired Boilers Yesa,b

Oil-Fired Furnace Yes

Electric Furnace Yes

Electric Air Conditioning Yes

Baseboard Electric (120/240 Line Volt) No

Heat Pumps/Multistage Equipment No

5 69-1385

❑Acquire tools and items as needed (see illustration). Also purchase two AA alkaline batteries; we

recommend Energizer® batteries.

M13544

CROSS-RECESSED

SCREWDRIVER

HAND OR

POWER DRILL

WITH 3/16 INCH

DRILL BIT, IF NEEDED

TO DRILL HOLES

IN WALL

WIRE CUTTER/STRIPPER OR SHARP

KNIFE, IF NEEDED TO STRIP WIRES

LEVEL, IF NEEDED TO LEVEL

THERMOSTAT FOR APPEARANCE

6 69-1385

Step 2. Remove Old Thermostat

❑Test to be sure your heating and cooling

systems are working properly. If either does

not work, contact your local heating/air

conditioning dealer. To avoid compressor

damage, do not operate the cooling system

when outdoor temperature is below 50°F

(10°C).

❑Turn off power to the system at the furnace,

or at the fuse/circuit breaker panel.

❑Carefully unpack your new thermostat and

mounting plate, saving package of screws,

instructions and receipt.

❑Remove cover from old thermostat. If it does

not snap off when pulled firmly from the

bottom, check for a screw used to lock on

the cover.

❑Loosen screws holding thermostat to

subbase, wallplate or wall, and lift away.

❑Disconnect wires from old thermostat or

subbase. As you disconnect each wire,

attach one of the enclosed labels to each old

terminal designation. If there are only two

wires, they do not need labeling. If there is

an extra wire that is not connected to your

old thermostat, you also do not connect it to

your new thermostat. Keep the wires from

falling back into the wall by wrapping them

around a pencil as shown.

WIRES THROUGH

WALL OPENING

M5136

7 69-1385

Replacing a Clock Thermostat that has

C or C1 Clock Terminals?

If you are replacing a Honeywell Chronotherm®

Thermostat, you may find one or two wires that

go to the C or C1 clock terminals on the

Chronotherm® Thermostat wiring wallplate. Do

not allow them to touch, or you can damage

your transformer. Disconnect the wires and

wrap them separately, using electrical tape. Do

not wrap them together. Place the wires where

they do not interfere with the operation of the

new thermostat. Record the colors and terminal

designation labels of the remaining wires.

Six or more wires?

If there are six or more wires (excluding clock

wires attached to terminals), you probably have

a variation of a heat pump or multistage

system. This thermostat is not compatible with

those systems so return the product to the

retailer. If you want information about the

programmable thermostats that work with your

system, call Honeywell Consumer Services at

1-800-468-1502.

Three thermostat wires?

If you have three wires for heating only and can

operate the fan using the fan On switch, this

thermostat works with your system. However,

some hot water (zoned) heating systems have

three thermostat wires. The thermostat does

not work without installing an isolating relay on

these systems. For details, call Honeywell

Consumer Services at 1-800-468-1502.

8 69-1385

Step 3. Install Batteries

IMPORTANT

Batteries must be installed for the pro-

gramming and operation of the ther-

mostat and heating/cooling system.

❑Purchase two AA alkaline batteries; non-

alkaline batteries do not last as long, and

can leak, causing damage to the thermostat

or the wall surface. We recommend

Energizer® batteries.

❑Open the top cover of thermostat to access

control panel and battery compartment.

❑Make sure the thermostat is set to the Off

position.

❑Use a coin to remove the battery cover.

M12492

REMOVING

BATTERY

DOOR

BATTERY

DOOR COVER

9 69-1385

❑Install the fresh batteries as shown, making

sure positive and negative terminals are

oriented correctly.

❑Replace the battery cover.

As the batteries run low, a bAt Lo indicator

flashes for one to two months before the

batteries run out completely. Replace the

batteries as soon as possible after the indicator

starts flashing. If you do not replace the

batteries sometime during the flashing bAt Lo,

the indicator eventually stops flashing. bAt Lo

then stays on without flashing, indicating the

thermostat and heating/cooling system have

stopped working and the batteries are almost

completely dead.

After the batteries are completely dead, the

bAtLo indication disappears, leaving a

completely blank display.

INSTALL TWO AA ALKALINE

BATTERIES AS SHOWN

M1713

10 69-1385

Press down on the left ends of batteries to

remove them. If you insert the new batteries

within 20 to 30 seconds of removing the old

ones, you do not need to reprogram the

thermostat. However, if the display is blank, the

batteries are dead or incorrectly installed and

you must reprogram. See Step 4.

IMPORTANT

Although the thermostat has a low bat-

tery indicator, replace the batteries

once a year to prevent the thermostat

and heating/cooling system from shut-

ting down due to lack of battery power.

As a precaution, when leaving home

for longer than a month, change bat-

teries before you leave to prevent the

system from shutting down due to lack

of battery power.

11 69-1385

Step 4. Program Thermostat

After the batteries are installed, the thermostat

can be easily programmed in your hand before

it is installed on the wall.

If you prefer to program the thermostat after it is

installed on the wall, go to Step 7 and return

later to this programming section.

The Personal Programming Chart, Tables 2 and

3, may be helpful for planning your program

schedule of time and temperature settings for

various times of the day.

Four time periods are available during

weekdays — WAKE, LEAVE, RETURN, and

SLEEP; view these periods individually on the

display as you press the Weekday key.

•WAKE is the time period you want the house

at a comfortable temperature when you get

up and while you get ready for work or

school. (This is a higher temperature during

heating season and a lower temperature dur-

ing cooling season.)

•LEAVE is the time period you can set for an

energy-saving temperature while you are

away at work or school. (This is a lower tem-

perature during heating season and a higher

temperature during cooling season.)

•RETURN is the time period you want the

house at a comfortable temperature for activ-

ities before bedtime. (This is a higher tem-

perature during heating season and a lower

temperature during cooling season.)

•SLEEP is the time period you can set for an

energy-saving temperature while you are

sleeping. (This is a lower temperature during

the heating season and a higher tem-

perature during the cooling season.)

12 69-1385

Set one schedule for weekdays and another for

weekends because your requirements are

usually different for each. Also, during week-

ends, only the WAKE and SLEEP time periods

are available.

Fill in the times and temperatures you desire for

weekdays and weekends. If you decide not to

program the thermostat, it automatically con-

trols heating at 68°F (20°C), and cooling at 78°F

(26°C), 24 hours a day. Also, you do not need to

enter a time and temperature program for all

periods if your schedule does not require it. For

example, a house that is occupied during week-

days would require programs only for WAKE

and SLEEP.

If no program is entered for the weekends, the

thermostat operates on the weekday SLEEP

program all weekend.

Before programming, remove the clear plastic

overlay covering the display.

When pressing the keys, use the ball of your

finger or a soft pencil eraser. Using sharp finger-

nails or pencil points can damage the keypad.

If you make an error at any time during program-

ming, just press the Run Program key, and

continue again at the previous step in your

sequence.

13 69-1385

aThe temperatures cannot be set any higher than 88°F (31°C) or any lower than 45°F (7°C).

bIf you decide not to enter weekend programs, the thermostat operates on the weekday SLEEP pro-

gram all weekend.

Table 2. Personal Programming Chart for Heating.

Days of Week Heating Program Start Time Heating Temperaturea

Weekdays

WAKE

LEAVE

RETURN

SLEEP

Weekendsb

WAKE

SLEEP

14 69-1385

.

aThe temperatures cannot be set any higher than 88°F (31°C) or any lower than 45°F (7°C).

bIf you decide not to enter weekend programs, the thermostat operates on the weekday SLEEP pro-

gram all weekend.

Table 3. Personal Programming Chart for Cooling.

Days of Week Cooling Program Start Time Cooling Temperaturea

Weekdays

WAKE

LEAVE

RETURN

SLEEP

Weekendsb

WAKE

SLEEP

15 69-1385

NOTE: Batteries are required for operation and programming. When inserting batteries, set the

System switch to Off. Remove the battery door (on the thermostat left side) using a coin at

the bottom. Follow instructions in Step 3. Also see the label inside the battery cover for

abbreviated programming procedures for your thermostat.

Set Current Time/Day

To set time, press and release once, press until current shows. To set day, press and

release again, press until current day shows; then press .

Heating Program

With System switch at Heat, press and release once. WAKE, MON FRI (Monday-Friday), and

SET appear on display.

Use to program WAKE time and to program WAKE temperature for MON FRI (Monday-Friday).

Repeat sequence for LEAVE, RETURN, SLEEP.

Clock/Day

Time

Clock/Day Time

Run Program

Weekday

Time TEMP

16 69-1385

Press until SAT SUN (Saturday-Sunday), WAKE and SET appear on display. Use to program

WAKE time and to program WAKE temperature for SAT SUN (Saturday-Sunday).

Repeat sequence for SLEEP. Press and release to start the program.

Cooling Program

With System switch at Cool, follow the same instructions as for the Heating Program.

After programming, adjust the Fan and System switches, as desired. Press and release to

start the program.

Weekend

Time

TEMP

Run Program

Run Program

17 69-1385

Operating Your Thermostat

System switch must be set to Heat or Cool to perform the following:

Temporarily Change Temperature for current period only — Press ; temporary indicator shows

on display and cancels itself at the next scheduled change; to cancel sooner, press .

Hold a Temperature Indefinitely (such as when on vacation) — Press and ; HOLD

appears on display; to cancel, press .

Check Current Temperature Setting — Press .

Check Programs — Press , repeatedly to see each time and temperature; then press

.

TEMP

Run Program

Hold Temp

TEMP

Run Program

Present Set

Weekday Weekend

Run Program

18 69-1385

Cancel Program — Press , until program to cancel shows; then press .

Check Usage — Press to see length of time heat or air conditioning has run today since

midnight; press again for yesterday’s usage, press again for cumulative; press to clear

cumulative reading, if desired; then press .

Permanently Change a Program — Repeat Heating Program or Cooling Program steps, as

applicable.

Return to Normal Program or Start Program — Press .

Weekday Weekend Clear

Usage

Clear

Run Program

Run Program

19 69-1385

Step 5. Adjust Fan Operation

Switch, As Required

❑The thermostat fan operation switch, labeled

FUEL SWITCH (see illustration) is factory-set

in the F position. This is the correct setting for

most systems. If your system is an electric

heat system, set the switch to E to allow the

fan to turn on immediately with the heating in

a system when the G terminal is connected.

Step 6. Adjust System On-Time,

°F/°C, As Required

❑The thermostat on-time is factory-set for a

warm air, gas or oil heating system. If you are

installing it on another type of system, adjust

the on-time accordingly by setting screws A

and B on the back of the thermostat. Use the

heating system table shown in the illustration

as a guide. The system on-time should be

optimized according to the type of system to

maximize comfort. Setting the screw “out one

turn” means turning the screw approximately

360° counterclockwise, or about one com-

plete turn.

RRc

W Y G

B D

A C

THERMOSTAT BACK

M8796A

DISPLAY °F

DISPLAY °CC–IN

C–OUT

1 TURN

FOR HIGH EFFICIENCY FURNACE (90%+ AFUE)

ADJUST: SCREW A–OUT ONE TURN

SCREW B–IN

FUEL SWITCH – F POSITION

FE

FUEL SWITCH

WARM AIR

FURNACE

HOT WATER

BOILER

ELECTRIC

FURNACE

A–IN

A–OUT

1 TURN

A–IN

ADJUST SCREWS THROUGH HOLES

TO SELECT OPERATION DESIRED

B–IN

B–IN

B–OUT

1 TURN

FUEL SWITCH

POSITION

F

F

E

HEATING SYSTEM

20 69-1385

In the unlikely event that you want a longer

furnace on-time, readjust screws A and/or B as

follows:

First, turn both screws in completely, then

adjust for system type:

•Warm Air Furnace—Set at the Hot Water

setting (A—out one turn, B—leave in).

•Electric Furnace—Leave at the Warm Air

Furnace setting (A—leave in, B—leave in).

NOTE: This thermostat does not have a set-

ting for steam/gravity air; cycles would

not be long enough for accurate tem-

perature control.

IMPORTANT

When using a high efficiency furnace

such as a 90 percent or greater Aver-

age Fuel Utilization Efficiency (AFUE)

unit, adjust screw A out one turn and

leave screw B in.

❑The thermostat is set to read the temperature

in degrees Fahrenheit. If readings are

desired in degrees Celsius, adjust screw C

out one turn.

21 69-1385

Step 7. Mount Thermostat

Mounting Plate

❑ Position mounting plate on wall. Use level to

make sure mounting plate is level. Use a

pencil to mark the two mounting holes.

❑Remove mounting plate from wall, and drill

3/16-inch holes in wall (if drywall) as marked.

For firmer material such as plaster or wood,

drill 7/32-inch holes. Gently tap anchors

(provided) into drilled holes until flush with the

wall.

❑Reposition mounting plate over holes,

pulling wires through wiring opening.

❑ Loosely insert two mounting screws into

holes.

WALL

WIRES THROUGH

WALL OPENING

WALL ANCHORS (2)

MOUNTING

PLATE

MOUNTING

SCREWS

(

2

)

M1718

22 69-1385

❑Level for appearance only; thermostat

functions properly even when not level.

❑Tighten mounting screws.

LEVEL

M1714A

23 69-1385

Step 8. Wire Thermostat Terminals

NOTE: All wiring must comply with local codes

and ordinances. If unsure about house-

hold wiring procedures, call your local

heating/air conditioning contractor.

❑Refer to the labels you placed on the terminal

wires when you removed your old thermostat.

Match the letter of your old thermostat wire

with the terminal of the corresponding letter

on the back of your new thermostat. (See

wiring diagrams.) Hold the thermostat as

shown in illustration to minimize need for wire

extenders. If wires are still too short, use wire

connectors (purchased locally) to extend

wires. See illustration for guidelines on using

wire extenders.

❑In 5-wire installations only, be sure to remove

the factory-installed jumper connecting termi-

nals R and Rc.

M1715A

WIRE

FROM

WALL

6 IN. (152 MM)

OF 18-GAUGE

THERMOSTAT

WIRE. MATCH

INSULATION

COLORS

OR MARK

WIRE ENDS.

WIRE NUT SIZE FOR

TWO 18-GAUGE WIRES

METHOD TO INCREASE WIRE LENGTH

24 69-1385

❑Loosen the terminal screws and slip each wire beneath its matching terminal. See illustrations for

wire insertion technique.

❑Securely tighten terminals.

❑Plug the hole in the wall with insulation to help prevent drafts from adversely affecting thermostat

operation.

M3002A

M1712B

JUMPER (FACTORY-

INSTALLED). REMOVE

IF 5-WIRE SYSTEM

INSERT

STRAIGHT

UNDER

SCREW HEAD

5/16 in.

(8 mm)

STRIP

END OF WIRE

VISIBLE HERE

RRc

WY G

25 69-1385

RRc

W Y G

B D

A C

2-WIRE HEAT-ONLY (JUMPER INTACT)

M1709B

L1

(HOT)

L2

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND

OVERLOAD PROTECTION AS REQUIRED.

1

1

HEATING

RELAY OR

VALVE COIL

JUMPER

RRc

W Y G

B D

A C

4-WIRE HEAT/COOL (JUMPER INTACT)

L1

(HOT)

L2

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND

OVERLOAD PROTECTION AS REQUIRED.

1

JUMPER

HEATING

RELAY OR

VALVE COIL

M1710B

COOLING

CONTACTOR

COIL

FAN

RELAY

26 69-1385

RRc

W Y G

B D

A C

5-WIRE HEAT/COOL (JUMPER REMOVED)

L1

(HOT)

L2

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND

OVERLOAD PROTECTION AS REQUIRED.

1

M1711C

L1

(HOT)

L2

COOLING

CONTACTOR

COIL

FAN

RELAY

HEATING

RELAY OR

VALVE COIL

1 1

RRc

W Y G

B D

A C

3-WIRE COOL-ONLY (JUMPER INTACT)

L1

(HOT)

L2

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND

OVERLOAD PROTECTION AS REQUIRED.

1

JUMPER

M848A

COOLING

CONTACTOR

COIL

FAN

RELAY

27 69-1385

Step 9. Mount Thermostat

NOTE: To remove thermostat from wall, first pull out at bottom of thermostat, then remove top.

M13545

PRESS LOWER EDGE

OF CASE TO LATCH.

ENGAGE TABS AT TOP OF

THERMOSTAT AND SUBBASE. SWING OPEN COVER TO

CHECK OPERATION.

A. B. C.

System

Cool Off Heat

Fan

OnAuto

LEAVE

TU

AM

TimeTEMPRun Program

Present Set

WeekendClearUsage

Hold Temp

Weekday

Clock/Day

28 69-1385

Step 10. Check Thermostat

Operation After Programming

and Installing

Heating

Do not check heating system operation by

jumpering thermostat terminals such as gas

valve, zone valve, and oil burner control at the

primary control. This damages the thermostat.

Instead, jumper R and W wires at the

thermostat.

Move the System switch to

Heat and the Fan switch to

Auto.

Press TEMP key until the set-

ting is about 10°F (6°C) above

room temperature. Heating

should start and the fan should

run after a short delay (immedi-

ately if fan operation switch is set to E position).

Press TEMP key until setting is about 10°F (6°C)

below room temperature. The heating equip-

ment should shut off.

TEMP

HeatCool Off

M1703

Auto On

M1705

29 69-1385

Cooling

To avoid possible compressor damage, do not

operate the cooling system when outdoor

temperature is below 50°F (10°C). See

compressor manufacturer instructions.

IMPORTANT

When cooling setting is changed, ther-

mostat delays up to five minutes

before turning on the air conditioner.

This delay protects the compressor.

Move the System switch to

Cool and the Fan switch to

Auto.

Press TEMP key until setting is

about 10°F (6°C) below room

temperature. The cooling

equipment and fan should start.

Press TEMP key until the setting is about 10°F

(6°C) above room temperature. The cooling

equipment and fan should stop.

Move the System switch to Off;

keep the Fan switch at Auto.

The system and fan should be

off.

TEMP

HeatCool Off

M1704

Auto On

M1705

HeatCool Off

M1707

Auto On

30 69-1385

Step 11. Set Fan and System Switches

First set the Fan switch.

Fan Auto: Normal setting for most

homes. A single-speed fan will

turn on automatically with the air

conditioner or furnace. A two-speed fan

usually runs on high with the air conditioner

and on low with the furnace.

Fan On: The fan runs continuously.

Use for improved air circulation

during special occasions or for

more efficient electronic air

cleaning. (In a heat-only system, fan runs

continuously only if fan relay is connected to

the thermostat.)

Then set the System switch.

Cool: The thermostat controls

your air conditioning

system.

Off: Both the heating and air

conditioning systems are

off.

Heat: The thermostat

controls your heating

system.

Auto On

Auto On

HeatCool Off

HeatCool Off

HeatCool Off

31 69-1385

Troubleshooting Guide

If... Then...

Display does not come on. Set the System switch to Off. Remove batteries. Insert them backward

for at least five seconds to reset the thermostat. Replace batteries

correctly. Display should come on.

Make sure batteries are fresh and installed correctly.

Temperature display does

not go lower than 45°F

(7°C) or higher than 88°F

(31°C) during programming.

You have reached the temperature setting limit. The setting range is

45°F to 88°F (7° to 31°C).

Temperature change occurs

at wrong times. Check the program times for the questionable period. Be sure that AM

and PM indications are correct. Make sure the current day and time

are correct. Reprogram, if necessary.

32 69-1385

Heating does not come on. Check that the System switch is set to Heat.

Make sure the heating setpoint is above the room temperature.

Check the system fuse or circuit breaker and replace or reset, if

necessary.

Make sure the System switch is in the On position; set it to On if it is in

the Off position.

If temperature setting is higher than the current temperature and the

display says HEAT, contact Honeywell Consumer Services at 1-800-

468-1502.

Cooling does not come on. Check that the System switch is set to Cool.

Make sure the cooling setpoint is below the room temperature.

Check the system fuse or circuit breaker and replace or reset, if

necessary.

Make sure the System switch at the air conditioner is in the On

position; set it to On if it is in the Off position.

If... Then...

33 69-1385

Cooling does not come on

(Continued). The thermostat has a built-in time delay on cooling. Allow five to ten

minutes after changing the setting before the air conditioner starts.

If temperature setting is lower than current temperature, and the

display says COOL, move the System switch from Cool to Off for ten

minutes. After ten minutes, return the switch to the Cool position. If air

conditioner comes on, compressor may have reached its high-limit

temperature protection and shut down.If air conditioner does not come

on after the ten minutes and the display says COOL, contact

Honeywell Consumer Services at 1-800-468-1502.

If two- or four-wire installation, verify R-Rc jumper is installed.

The house is too warm or

too cool. Press Present Set key to check the current temperature setting.

If desired, change the temperature setting. See Cooling Program

section.

SYSTEM ON indicator is

lighted, but no heat is

coming from the registers.

Allow time for the furnace to heat up and the fan to come on before

checking for heat at the register. (Check to make sure system on-time

is set correctly. See Step 6.)

If... Then...

34 69-1385

Toll-free Customer Assistance

For all questions concerning this thermostat, please read and follow the instructions. If additional

assistance is needed, call Honeywell Consumer Services at 1-800-468-1502, Monday - Friday,

7:00 a.m. - 5:30 p.m. Central time.

Before you call, please have the following information available—thermostat model number and

date code, type of heating/cooling system (hot water, warm air, oil, gas, etc.), and number of wires

connected to the thermostat.

NOTICE

This equipment is a Class B digital apparatus, which complies with Canadian Radio Interference

Regulations, CRC c.1374.

35 69-1385

Limited One-Year Warranty

Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and

service, for a period of one (1) year from the date of purchase by the consumer. If, at any time during the warranty period, the

product is defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option) within a reasonable period of time.

If the product is defective,

(i) return it, with a bill of sale or other dated proof of purchase, to the retailer from which you purchased it, or

(ii) package it carefully, along with proof of purchase (including date of purchase) and a short description of the malfunction, and

mail it, postage prepaid, to the following address:

Honeywell Inc. Canada: Honeywell Limited/Honeywell Limitée

Return Goods Department Product ServicesON15-FFE

1050 Berkshire Lane 740 Ellesmere Road

Plymouth, MN 55441-4437 Scarborough, Ontario M1P 2V9

This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the

defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer.

Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT

BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY

OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential

damages, so this limitation may not apply to you.

36 69-1385

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF

ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, IS HEREBY LIMITED TO THE ONE YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations

on how long an implied warranty lasts, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

If you have any questions concerning this warranty, please write our Customer Assistance Center, Honeywell Inc., P.O. Box 524,

Minneapolis, MN 55440-0524 or call 1-800-468-1502, Monday-Friday, 7:00 a.m. to 5:30 p.m., Central time. In Canada, write

Retail Products ON15-02H, Honeywell Limited/Honeywell Limitée, 155 Gordon Baker Road, North York, Ontario M2H 2C9.

37 69-1385

30%

28%

26%

24%

22%

20%

18%

16%

14%

12%

8%

6%

2%

10%

4%

Minneapolis

St. Paul

Montreal

Ottawa

Toronto

Buffalo

Cleveland

Milwaukee

Edmonton

Regina

Winnipeg

Calgary

Moncton

North Bay

Quebec

St. John's

Halifax Vancouver Denver

Des Moines

Omaha

Salt Lake

City

Boston

Chicago

Detroit

Pittsburgh

Indianapolis

Cincinnati

Kansas City

St. Louis

Columbus

New York

Philadelphia

Seattle

Louisville

Portland

Wash., D C

San

Francisco

Dallas

Atlanta Los Angeles

Approximate percentage of energy cost savings

Savings for Once-A-Day

10°F (5°C) decrease Savings for Twice-A-Day

10°F (5°C) decrease* Savings for 5°F (3°)

summer increase

TYPICAL ENERGY SAVINGS FOR REPRESENTATIVE CITIES IN THE U.S. AND CANADA

*Based on 10°F (5°C) decrease—(5°F [3°C] decrease

gives approximately 55 percent of these savings).

M2416A

San Diego

38 69-1385

39 69-1385

69-1385 G.H. 6-00 www.honeywell.com/yourhome

Home and Building Control Home and Building Control

Honeywell Inc. Honeywell Limited-Honeywell Limitée

Honeywell Plaza 155 Gordon Baker Road

P.O. Box 524 North York, Ontario

Minneapolis, MN 55408-0524 M2H 3N7

Printed in U.S.A. on recycled

paper containing at least 10%

post-consumer paper fibers.