Honeywell Video Gaming Accessories W7750A Users Manual W7750A,B,C

2015-01-23

• Contents
• List of Figures
• List of Tables
• Introduction
  • Description of Devices
  • Control Application
  • Control Provided
  • Products Covered
  • Organization of Manual
  • Applicable Literature
  • Product Names
  • Agency Listings
  • Abbreviations and Definitions
  • Construction
    • Controllers
      • PERFORMANCE SPECIFICATIONS
      • LonMark® Functional Profile
    • Inputs/Outputs:
      • ANALOG INPUTS:
      • DIGITAL INPUTS:
      • TRIAC OUTPUTS ON THE (W7750B,C MODELS ONLY):
      • DIGITAL OUTPUTS:
    • Wall Modules
    • Duct Sensor
  • Configurations
    • General
    • Allowable Heating and Cooling Equipment Configurations
      • STAGED HEATING/COOLING CONTROL
      • MODULATING HEATING/COOLING CONTROL
      • HEAT PUMP CONTROL
      • ECONOMIZER CONTROL
      • PNEUMATIC ACTUATOR CONTROL
      • MIXED-OUTPUT-TYPE CONTROL
    • Occupancy Sensor
    • Window Open/Closed Digital Input
    • Wall Module Options
    • Dirty Filter Monitor
    • Indoor Air Quality (IAQ) Override
    • Smoke Control
    • Freeze Stat
  • Modes of Operation
• Application Steps
  • Overview
  • Step 1. Plan the System
  • Step 2. Determine Other Bus Devices Required
  • Step 3. Lay Out Communications and Power Wiring
    • LonWorks® Bus Layout
    • Power Wiring
      • POWER BUDGET CALCULATION EXAMPLE
      • LINE LOSS
  • Step 4. Prepare Wiring Diagrams
    • General Considerations
    • W7750 Controllers
      • FACTORY DEFAULT DIGITAL OUTPUTS:
    • LonWorks® Bus Termination Module
  • Step 5. Order Equipment
  • Step 6. Configure Controllers
  • Step 7. Troubleshooting
    • Troubleshooting Excel 10 Controllers and Wall Modules
    • Temperature Sensor and Setpoint Potentiometer Resistance Ranges
    • Alarms
    • Broadcasting the Service Message
    • W7750 Controller Status LED
    • T7770C,D Wall Module Bypass Pushbutton and Override LED
    • T7560A,B Digital Wall Module Bypass Pushbutton and LCD Display Occupancy Symbols
• Appendices
  • Appendix A. Using E-Vision to Commission a W7750 Controller.
    • Sensor Calibration
    • Setting the Pid Parameters
  • Appendix B. Sequences of Operation.
    • Common Operations
      • Room Temperature Sensor (RmTemp)
      • Remote Setpoint (RmtStptPot)
      • Setpoint Limits (LoSetptLim and HiSetptLim)
      • Bypass Mode (StatusOvrd and StatusLed)
      • BYPASSTIME
      • OverrideType
      • OverridePriority
      • Cycles per Hour (ubHeatCph and ubCoolCph)
      • T7770C,D or T7560A,B Wall Module Bypass Pushbutton Operation
      • Standby Mode (StatusOcySen)
      • Continuous Unoccupied Mode
      • Occupancy Mode and Manual Override Arbitration
      • Time Clock (Occ_Time_Clock)
      • Schedule Master (Sched_Master)
      • Setpoint Ramping
      • Recovery Ramping for Heat Pump Systems
      • Fan Operation
      • Window Sensor (StatusWndw)
      • Smoke Control
      • Demand Limit Control (DLC)
      • Dirty Filter Monitor
      • Start-Up
    • Temperature Control Operations
      • Staged Cooling Control
      • Staged Heating Control
      • Cascade Control of Modulating Cooling/Heating
      • Series 60 Modulating Control
      • Pulse Width Modulating (PWM) Control
      • Outdoor Air Lockout of Heating/Cooling
      • Economizer Damper Control
      • Indoor Air Quality (IAQ) Override
      • Freeze Stat
      • Discharge Air Low Limit Control
      • Economizer Enable/Disable Control
  • Appendix C. Complete List of Excel 10 W7750 Controller User Addresses.
    • User Address Indexes (all in alphabetical order)
    • Mappable User Addresses and Table Number
    • Failure Detect User Addresses and Table Number
  • Appendix D. Q7750A Excel 10 Zone Manager Point Estimating Guide.
    • Approximate Memory Size Estimating Procedure.
  • Appendix E. Sensor Data for Calibration.
    • Resistance Sensors.
    • Voltage/Current Sensors.