Honeywell LXE4831P MX9, FC300 Handheld computer User Manual PDF Output

Honeywell International, Inc. MX9, FC300 Handheld computer PDF Output

UserManual.wiki >

LXE4831P User Manual >

Users Manual F300

Contents

Users Manual F300

2009 Copyright© by LXE®, Inc, An EMS Technologies Company. All Rights Reserved.FC300 User GuideWH-FC300USER-001For Review - Do Not Distribute - LXE Confidential

Table of ContentsIntroduction 1Laser Warnings and Labels 2Label Location 2Label 2Set Up A New FC300 3Hardware Setup 3Software Setup 3Batteries 4How To Connect or Remove the Battery Pack 4Insert/Replace Battery 4Remove Battery 4Insert Battery in HazLoc FC300 5Remove Battery from HazLoc FC300 5Hotswap the Main Battery 5Tapping the Touchscreen with a Stylus 6Backlights and Indicators 7Status LEDs 7System Status LED 7Battery Charging Status LED 7Bluetooth Status LED 7Keypad Backlight Setting 8Connecting Cables to the FC300 9Connecting the USB Host and Power Cable 9Host Cable Assembly 9Connecting the USB Client and Power Cable 10Client Cable Assembly 10Connecting the Serial and Power Cable 11Serial/Power Cable Assembly 11Connecting an External Power Supply 12Connecting Vehicle Power 12Connecting the Headset Cable 13Adjust Headset / Microphone and Secure Cable 14Connecting a Tethered Scanner 15Attaching the Handstrap 16Assemble the Carry Case 17Carry Case with Metal Snaps 17WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

iiSet Date and Time Zone 18Grab Time Utility 18Using the Input Panel / Virtual Keyboard 19Set Power Scheme Timers 20Battery Power Scheme 20AC Power Scheme 20Set Speaker Volume 21Using the Keypad 21Using the Control Panel 21Touchscreen 22Calibrating the Touchscreen 22Adjust the Display Backlight Brightness 22Adjusting the Display Backlight Timer 22Apply the Touchscreen Protective Film 23Cleaning 23Using the AppLock Switchpad 24Using the Keypad 24Using the Touchscreen 24Connecting to Bluetooth Devices 25Taskbar Connection Indicator 25LED Connection Indicator 25Reboot 26Warm Boot 26Troubleshooting 26Regulatory Notices and Safety Information 27Class B Digital Device 27RF Notices 28AC Power Supply Safety Statement 29Laser Light Safety Statement 30Hazardous Locations Warnings 32Index 33FC300 User Guide WH-FC300USER-001For Review - Do Not Distribute - LXE Confidential

IntroductionThe Itron® FC300 is a ruggedized handheld computer targeted for indoor and outdoor use. It is powered by alightweight main battery that can be removed and replaced without the need for special tools.FC300 wireless connectivity is secured by user-configured encryption and authentication protocols. TheFC300 has an integrated keyboard, outdoor readable touch display, a tethered stylus, Microsoft® Windows®CE® 5.0 operating system, and many wireless connection options.The keypad is available in a 62-key configuration. The 62-key keypad is also available in a Frenchconfiguration.Barcode reader options are: an imager integrated in the FC300, or a handheld scanner tethered to the port atthe base of the FC300, Bluetooth mobile barcode imagers and scanners, or the LXE Bluetooth ring scanner /ring imager.Wireless network connection can be accomplished using a Summit WLAN 802.11 radio, WWAN, andBluetooth.Desk and vehicle cradles, a handstrap, holsters with shoulder straps or belts, Bluetooth scanners and printer,a battery and in-vehicle battery chargers are among the many accessories available for the FC300.Note: This document contains start up information and instruction for the FC300 end-user. Technicaland advanced instruction is contained in the FC300 Reference Guide.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

2 Laser Warnings and LabelsLaser Warnings and Labels●Do not look into the laser’s lens.●Do not stare directly into the laser beam.●Do not remove the laser caution labels from the FC300.●Do not connect the laser barcode aperture to any other device. The laser barcode aperture is certifiedfor use with the FC300 only.Caution: Laser radiation when open. Please read the caution labels. Use of controls, adjustments or per-formance of procedures other than those specified herein may result in hazardous radiation expo-sure.Label LocationLabelWH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

3 Set Up A New FC300Set Up A New FC300Note: LXE recommends that installation or removal of accessories be performed on a clean, well-litsurface. When necessary, protect the work surface, the FC300, and components from electrostaticdischarge.While the FC300 is in a Hazardous Location DO NOT:●Connect an external power source to the FC300.●Connect a USB device or audio jack to the FC300.●Connect the Car Power Adapter to the I/O connector at the base of the FC300.●Remove or install a battery pack in the FC300.●Connect a tethered scanner to the FC300.●Place the FC300 in a powered cradle.Hardware Setup1. Connect accessories.2. Connect cables.3. Insert/connect a fully charged battery4. Press the Power key.Software SetupPrerequisite: Hardware setup is complete.1. Calibrate Touch screen2. Set Date and Time Zone3. Set Power Schemes Timers4. Set Speaker Volume5. Pair Bluetooth devices6. Save changed settings to the registryWH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

4 BatteriesBatteriesHow To Connect or Remove the Battery PackWarning: Never remove or replace any battery in a hazardous location.Note: The FC300 will not function unless the battery pack is in place and securely latched.Note: Be sure to place the unit in Suspend Mode (by pressing the Power key or tapping Start | Suspend)before removing the battery. Failing to properly place the device in Suspend mode will result in a loss ofall unsaved data.The main battery is located in a compartment on the back of the unit. The battery case serves as the backcover for the battery well of the FC300.With a fully charged backup battery, an FC300 will retain data, while the main battery is removed and replacedwith a fully charged main battery, for 5 minutes. Important: When the backup battery power is Low or VeryLow connect the AC adapter to the FC300 before replacing the main battery.Note: The battery should not be replaced in a dirty, harsh or hazardous environment. When the battery isnot connected to the FC300, any dust or moisture that enters the battery well or connector may transferto the battery/well terminals, potentially causing damage.Warning : Only use LXE MX9380BATTERY 161888-0001 or 161915-0001 (Low Temperature) 163086-0001batteries as replacements.Insert/Replace BatteryTo insert the main battery, complete the following steps:1. Detach the bottom hook of the handstrap (if installed).2. Tilt the end (with the terminals) of the fully charged battery pack into the upper end of the battery com-partment, and firmly press down on the other end until it is fully inserted into the battery compartment.3. Push down on the battery until the retaining clip clicks into place.4. Replace the handstrap clip in its holder (if installed).The FC300 draws power from the battery immediately upon successful terminal connection.Check battery status by tapping the Start | Settings | Control Panel | Battery icon. Main battery level,status and other details are displayed.Remove BatteryTo remove the battery, complete the following steps:1. Place the FC300 in Suspend mode.2. Detach the bottom hook of the handstrap (if installed).3. Slide the battery retaining clip down to release the main battery.4. Pull the battery up and out of the battery well with a hinge motion.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

Insert Battery in HazLoc FC300 5Insert Battery in HazLoc FC3001. Detach the bottom hook of the handstrap (if installed).2. Tilt the end (with the terminals) of the fully charged battery pack into the upper end of the battery com-partment, and firmly press the other end until it is seated into the battery compartment.3. Push down on the battery pack until it clicks into place.4. Place the tethered plastic locking tab over the battery latch, matching up the screw holes in theFC300 and the screw holes in the tethered plastic locking tab.5. Using a flat head screwdriver, secure the battery in the battery well by securing the locking screws tothe FC300 body.6. Replace the hand strap clip in its holder.Remove Battery from HazLoc FC3001. Place the FC300 in Suspend mode.2. Detach the bottom hook of the handstrap (if installed).3. Using a flat head screwdriver, unfasten the tethered plastic lock's captive locking screws.4. Place the tethered plastic locking tab to one side. Do not remove or unfasten the tether.5. Press the battery locking tab down to release the battery pack.6. Pull the battery up and out of the battery well with a hinge motion.Hotswap the Main BatteryWarning: Never replace (hotswap) the FC300 battery in a hazardous location.Place the FC300 in Suspend Mode. Itron recommends any work in progress be saved prior to replacing thebattery pack.Simply replace the discharged battery with a fully-charged battery. An FC300, with a fully charged backupbattery, will retain data during a battery hotswap for 5 minutes.FC300 User Guide WH-FC300USER-001For Review - Do Not Distribute - LXE Confidential

6 Tapping the Touchscreen with a StylusTapping the Touchscreen with a StylusNote: Always use the point of the stylus for tapping or making strokes on the touchscreen.Never use an actual pen, pencil, or sharp/abrasive object to write on the touchscreen.Hold the stylus as if it were a pen or pencil. Touch an element on the screen with the tip of the stylus thenremove the stylus from the screen.Firmly press the stylus into the stylus holder when the stylus is not in use.Using a stylus is similar to moving the mouse pointer then left-clicking icons on a desktop computer screen.Using the stylus to tap icons on the touchscreen is the basic action that can:●Open applications●Choose menu commands●Select options in dialog boxes or drop-down boxes●Drag the slider in a scroll bar●Select text by dragging the stylus across the text●Place the cursor in a text box prior to typing in data●Place the cursor in a text box prior to retrieving data using the scanner/imager or an input/output deviceconnected to the serial port.A right-click can be simulated by touching the touchscreen with the stylus and holding it for a short time.A stylus replacement kit is available.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

7 Backlights and IndicatorsBacklights and IndicatorsStatus LEDsSeveral LEDs are located on the front of the FC300 above the integrated speaker. They are:●System Status LED indicates power management status.●Battery Charging Status LED indicates main battery charging status.●Bluetooth Status LED applies to Bluetooth client functions.System Status LEDBlinking Red Battery power fail; critical suspendSolid Red Main battery lowBlinking Green Display turned offYellow / Amber Initial few seconds when Power key is pressedBattery Charging Status LEDOff No battery, no AC power, battery pack not plugged in or no AC power appliedFlashing Red Fault, battery pack fault or failureYellow / Amber Standby, battery pack temperature out of rangeRed Charging, battery pack charging (icon on touchscreen)Green Charged, battery pack fully charged. Connected to external power.Bluetooth Status LED●Blue when Bluetooth activated●Off when Bluetooth not activated.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

8 Keypad Backlight SettingKeypad Backlight SettingStart | Settings | Control Panel | KeyMapThe keypad backlight is white and can be set to be on or off.The default value is on.When set to off, the keypad backlight does not turn on during Suspend/Restart or reboots.When set to on, the keypad backlight follows the display backlight settings. The keypad backlight turns offwhen the display backlight dims.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

9 Connecting Cables to the FC300Connecting Cables to the FC300Note: Do not connect or disconnect cables in a Hazardous location.Connecting the USB Host and Power CablePrerequisite : AC/DC Adapter, AssembledNote: Do not connect AC power to the AC Adapter yet.Host Cable Assembly1. Holding the cable I/O connector, pinch the catch release buttons in until the catches are open. Connectthe cable to the FC300 I/O port by matching the shape of the I/O connector on the cable with the shapeof the I/O connector at the base of the FC300. Release the catch release buttons.2. Insert the AC adapter single pin cable (2).3. Connect the AC Adapter to a power source (wall outlet).4. Insert the USB host plug (3) into the USB Host port.The FC300 and the host device are connected.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

10 Connecting the USB Client and Power CableConnecting the USB Client and Power CablePrerequisite : AC/DC Adapter AssembledNote: Do not connect AC power to the AC Adapter yet.Client Cable Assembly1. Holding the cable I/O connector (3), pinch the catch release buttons in until the catches are open. Con-nect the cable to the FC300 I/O port by matching the shape of the I/O connector on the cable with theshape of the I/O connector at the base of the FC300. Release the catch release buttons.2. Insert the AC adapter single pin cable (2) .3. Connect the AC Adapter to a power source (wall outlet).4. Insert the USB client plug (1) into the target USB Client port.The FC300 and the USB client are connected.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

11 Connecting the Serial and Power CableConnecting the Serial and Power CablePrerequisite : AC/DC Adapter, AssembledNote: Do not connect AC power to the AC Adapter yet.Serial/Power Cable Assembly1. Holding the cable I/O connector (1) , squeeze the catch release buttons in until the catches are open.Connect the cable to the FC300 I/O port by matching the shape of the I/O connector on the cable withthe shape of the I/O connector at the base of the FC300. Release the catch release buttons.2. Connect the AC adapter single pin cable end here (2).3. Connect the assembled AC/DC Adapter to a power source (wall outlet).4. Connect the RS-232 cable end (3) to the desired serial device. Turn the thumbscrews clockwise untilthe connection is finger-tight.The FC300 and the serial device are connected.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

12 Connecting an External Power SupplyConnecting an External Power Supply1. Connects to AC single-pin cable end2. AC receptacle3. Wall plug4. AC connection from wall to adapterTo apply external power to the FC300 follow the steps below in sequence.1. Plug the 3 prong AC adapter cable end of the external power assembly into an AC power source (e.g.wall outlet).2. Firmly press the female end of the power cable into the male connector on the power adapter. WhenAC power is being supplied to the power adapter, the LED on the power adapter illuminates green.3. Squeeze the catches of the I/O connector and push the cable connector into the FC300 I/O port until itclicks. The click means the connector is seated firmly.4. Press the power cable connector pin from the power adapter into the connector on the (USB/Power orSerial/Power) cable attached to the base of the FC300. External power is now being supplied to theFC300.Whenever possible, use the AC power adapter with the FC300 to conserve the main battery powerConnecting Vehicle PowerComplete vehicle cradle mounting and power instruction is contained in the FC300 Cradle Guide.The FC300 must have a main battery installed before docking the FC300 in a vehicle cradle.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

13 Connecting the Headset CableConnecting the Headset CableHeadset1. Connects to voice cable end of voice cable2. Headphones3. MicrophoneConnect the FC300 voice cable I/O connector to the I/O port on the FC300. The FC300 internal microphoneand speaker are automatically disabled.Slide the voice cable ends together until they click shut. Do not twist or bend the connectors.The FC300 is ready for voice-enabled applications.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

14 Adjust Headset / Microphone and Secure CableAdjust Headset / Microphone and Secure CableThe headset consists of an earpiece, a microphone, a clothing clip and a cable. The headset attaches to theaudio cable end of the voice cable which attaches to the FC300.Align the audio connector and the headset quick connect cable end. Firmly push the cable ends together untilthey click and lock in place.Do not twist the microphone boom when adjusting the microphone. The microphone should be adjusted to beabout two finger widths from your mouth.Make sure the microphone is pointed at your mouth. Note the small “Talk” label near the mouthpiece. Makesure the Talk label is in front of your mouth. The microphone cable can be routed over or under clothing.Under Clothing●Leave the cable exposed only at the top of the collar.●Be sure to leave a small loop of cable to allow movement of your head.Over Clothing●Use clothing clips to hold the cable close to your body.●Tuck the cable under the belt, but leave a small loop where it goes under the belt.●Do not wear the cable on the front of your body. It may get in your way or get caught on protrudingobjects.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

15 Connecting a Tethered ScannerConnecting a Tethered Scanner1. Connect to I/O port2. Connect to tethered scanner1. Squeeze the I/O port connector latches inwards. Connect part (1) of the RS232 cable to the I/O port atthe base of the FC300. Release the connector latches and test the connection for stability.2. Match the shape of the serial port (2) on the RS232 cable with the shape of the tethered scanner cableend.3. Press the ends firmly together.4. Secure the connection by tightening the thumbscrews on the tethered scanner cable end until they arefinger tight.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

16 Attaching the HandstrapAttaching the Handstrap1. Place the FC300 with the screen facing down, on a flat stable surface.2. Place the handstrap base (2) in the grooved area, matching the screw holes in the handstrap base withthe screw holes in the body of the FC300.3. Insert the screws (supplied) into each of the four holes and fasten the base securely.4. Slide the handstrap bottom clip pins into the slots at the base of the FC300 and pull the strap towardsthe top of the FC300 until the top clip slips into the groove.5. Making sure the closed loop fastener surface on the handstrap are facing up, slide the strap through thelatch in the top clip.6. Fold the end of the strap over so that the closed loop fastener surfaces mate evenly and the handstrapis secured to the FC300.7. Test the strap's connection making sure the FC300 is securely connected to each end of the strap con-nectors.Check the closed loop fastener and handstrap base connection frequently. If loose, they must be tightened orreplaced before the FC300 is placed into service again.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

17 Assemble the Carry CaseAssemble the Carry CaseNote: Itron recommends that accessory installation or removal be performed on a clean, well-lit surface.When necessary, protect the work surface, the FC300, and components from electrostatic discharge.1. Remove any cables connected to the I/O port at the bottom of the FC300.2. Separate the hook and loop fabric on the carry case without removing the hook and loop fabric from thecarry case.3. Slip the removable, clear plastic protector for the keypad and touchscreen into the case. Position itagainst the openings for the keypad and touchscreen in the case. The voice case does not require theclear plastic protector.4. Slide the FC300 into the case, making sure the touchscreen and keypad (including the Scan LED) arevisible and accessible through the front openings of the case.5. Securely tether the stylus to the case, if necessary. Place the stylus in the stylus holder on the hand-strap or the trigger handle.6. Loosen then tighten the handstrap (on cases without a trigger handle opening) until the carry caseassembly is secure in your hand.7. When a shoulder strap is available,secure the clips at each end of the shoulder strap to the D rings oneither side of the carry case. The shoulder strap allows the FC300 to hang upside down until needed.The main battery can be removed and inserted without taking the FC300 out of the carry case.Carry Case with Metal SnapsThe metal snap has a bulge in the lip and a dot indentation on the opposite side. To snap the cap closed, tuckthe lip bulge under the snap lip and press on the dot to snap closed.Pull the snap up to open.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

18 Set Date and Time ZoneSet Date and Time ZoneStart | Settings | Control Panel | Date/Time iconSet Date, Time, Time Zone, and assign a Daylight Savings location on the FC300 after a warm boot oranytime.There is very little functional change from standard desktop PC Date/Time Properties options. Adjust thesettings and tap the OK button or the Apply button to save changes to the registry. Any changes take effectimmediately.Double-tapping the time displayed in the Taskbar causes the Date/Time Properties screen to appear.Grab Time UtilityThe GrabTime utility can be configured to synchronize the time with a local server during each reboot function.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

19 Using the Input Panel / Virtual KeyboardUsing the Input Panel / Virtual KeyboardThe virtual keyboard is always available when needed e.g. text entry.Tap the Keyboard icon in the Taskbar to put the virtual keyboard on the display.Place the cursor in the text entry field and, using the stylus:●Tap the Shift key to type one capital letter.●Tap the CAPS key to type all capital letters.●Tap the áü key to access symbols.Some applications do not automatically display the Input Panel. In this case, do the following to use the InputPanel:Input Panel icon in the taskbar●Tap the Input Panel icon in the taskbar.●Select Keyboard from the menu.●Move the cursor into the text entry field when you want to enter data using the Input Panel.Keyboard icon in the taskbarWhen finished entering data, tap the Keyboard icon in the Taskbar. Select Hide Input Panel.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

20 Set Power Scheme TimersSet Power Scheme TimersStart | Settings | Control Panel | Power | SchemesChange the parameter values and tap OK to save the changes.Battery Power SchemeUse this option when the FC300 will be running on battery power only.Switch state to User Idle1Default is After 3 secondsSwitch state to System Idle2Default is After 15 secondsSwitch state to Suspend3Default is After 5 minutesAC Power SchemeUse this option when the FC300 will be running on external power (e.g. connected to an A/C power source).Switch state to User Idle Default is After 2 minuteSwitch state to System Idle Default is After 2 minutesSwitch state to Suspend Default is After 5 minutesThe timers are cumulative. The System Idle timer begins the countdown after the User Idle timer has expiredand the Suspend timer begins the countdown after the System Idle timer has expired. When the User Idletimer is set to “Never”, the power scheme timers never place the FC300 in User Idle, System Idle or Suspendmodes (even when the FC300 is idle).Because of the cumulative effect, and, using the Battery Power Scheme Defaults listed above:●The backlight turns off after 3 seconds of no activity,●The display turns off after 18 seconds of no activity (15 seconds + 3 seconds),●And the FC300 enters Suspend after 5 minutes and 18 seconds of no activity.1An amount of time has passed, set by the User Idle timer, and the device shuts down a minimum number ofservices e.g. backlights. The System Idle timer and the Suspend timer have not expired yet.2An amount of time has passed, set by the System Idle timer, and the device shuts down a few more servicese.g. touch display. The User Idle timer has expired and the Suspend timer has not expired yet.3Suspend mode is entered when (1) the unit is inactive for a predetermined period of time, (2) the user taps thePower key, or (3) Start | Suspend is chosen. Inactivity means that no internal devices are causing interrupts toreset the power state.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

21 Set Speaker VolumeSet Speaker VolumeThe speaker is located between the large keys and underneath the LEDs.Speaker volume can be adjusted to a comfortable level for the listener by using the keypad or by changingparameters in the Volume & Sounds control panel.Using the KeypadNote: Volume & Sounds (in Settings | Control Panel) must be enabled before the following keysequences can adjust the volume.The volume is increased or decreased one step each time the volume key sequence is pressed.To adjust speaker volume:●Blue+V+Up Arrow and Blue+V+Down Arrow keys●Press any key, except the keys used to adjust the volume, to exit.Volume control using a keypad key press has six volume settings that match those supported by the Volumeand Sounds Control panel. Volume does not “roll-over” from minimum to maximum or from maximum tominimum. Continuously holding down the up or down arrow keys does not cause an automatic repeat of the up(or down) arrow key.Using the Control PanelTap Start | Settings | Control Panel | Volume & Sounds | Volume tab. Change the volume setting andtap OK to save the change.You can also select / deselect sounds for key clicks and screen taps and whether each is loud or soft.As the volume scrollbar is moved between Loud and Soft, the FC300 emits a tone each time the volumeincreases or decreases.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

22 TouchscreenTouchscreenCalibrating the TouchscreenIf the touchscreen is not responding properly to stylus taps, you may need to recalibrate the touchscreen.Recalibration involves tapping the center of a target. If you miss the center, keep the stylus on the screen,slide it over the target's center, and then lift the stylus.To recalibrate the screen, select Start | Settings | Control Panel | Stylus | Calibration tab.To begin, tap the Recalibrate button on the screen with the stylus.Follow the instructions on the screen and press the Enter key to save the new calibration settings or pressEsc to cancel or quit.Adjust the Display Backlight BrightnessWhen the display backlight is on, press the Blue key and then press the Bkey.●Use the Up Arrow and Down Arrow keys to adjust backlight brightness until the display lightens ordarkens to your satisfaction.●Press any key, except the up arrow or down arrow keys, to exit this mode.At the minimum dimness level, the display is still viewable. The brightness setting is recalled upon a returnfrom Suspend and also upon a warmboot.Note: The brightness of the keypad backlight is not affected by display brightness adjustments or thedisplay brightness default setting.Adjusting the Display Backlight TimerStart | Settings | Control Panel | Display | BacklightThe backlight settings use the Itron set of default timeouts and are synchronized to the User Idle setting in theSchemes tab in the Power control panel.When the backlight timer expires, the display backlight is dimmed, not turned off. When both checkboxes areunchecked, the backlight never turns off (or dims).Default values are 3 seconds for Battery, 2 minutes for External and both the check boxes are enabled.When the keypad backlight is set to Follow the touchscreen backlight, the keypad backlight turns off whenthe touchscreen backlight dims.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

23 Apply the Touchscreen Protective FilmApply the Touchscreen Protective FilmFirst, clean the touchscreen of fingerprints, lint particles, dust and smudges.Remove the protective film from its container. Remove any protective backing from the film sheet by liftingthe backing from a corner of the film. Discard the backing.Apply the film to the touchscreen starting at one side and smoothing it across the display. If air bubblesappear, raise the film slightly and continue smoothing the film across the display until it covers the glasssurface of the display. If dust, lint or smudges are trapped between the protective film and the glass display,remove the protective film, clean the display and apply the protective film again.CleaningCleaning any area of the FC300 should only be done with mild household cleaning chemicals such as Windex.Cleaning chemicals should never be sprayed directly onto the FC300. Do not scrub optical surfaces. Ifpossible, clean only those areas which are soiled. Lint and particulates can be removed with clean, filteredcanned air. Apply the cleaning compound sparingly to a soft, non-abrasive cloth and rub gently. Use of harsherchemicals such as hand creams or insect repellent on the FC300 can damage the materials and void thewarranty.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

24 Using the AppLock SwitchpadUsing the AppLock SwitchpadNote: The touchscreen must be enabled. Select Start | Settings | Control Panel | Options | Misc. tab toverify touchscreen status.Switchpad Menu Switchpad Icon in TaskbarA checkmark indicates applications currently active or available for Launching by the FC300 user. WhenKeyboard, on the Switchpad Menu, is selected, the default input method (Input Panel, Transcriber, or custominput method) is activated.Using the KeypadOne switch key sequence (or hotkey) is defined by the Administrator for the end-user to use when switchingbetween locked applications. This is known as the Activation key.When the switch key sequence is pressed on the keypad, the next application in the AppLock configuration ismoved to the foreground and the previous application moves to the background. The previous applicationcontinues to run in the background. FC300 key presses affect the application in focus only.Using the TouchscreenThe figure shown above is an example and is shown only to aid in describing how the user can switchbetween applications using a stylus.When the user taps the Switchpad icon with the stylus, a menu pops up listing the applications available tothe user. The user can tap an application name in the popup menu and the selected application is brought tothe foreground. The previous application continues to run in the background. Stylus taps affect the applicationin focus only. When the user needs to use the Input Panel, they tap the Keyboard option. Input Panel tapsaffect the application in focus only.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

25 Connecting to Bluetooth DevicesConnecting to Bluetooth DevicesPrerequisites:●The system administrator has discovered and paired (using the default LXEZ Pairing Control Panel)Bluetooth devices for each FC300: one mobile Bluetooth scanner, two Bluetooth serial devices andone Bluetooth printer.●The system administrator has enabled and disabled LXEZ Pairing parameters for the FC300.●The system administrator has also assigned a Computer Friendly Name using the LXEZ Pairing Con-trol Panel for the FC300.To connect Bluetooth devices, the FC300 should be as close as possible and in direct line of sight with thetargeted Bluetooth device during the discovery and pairing process.If the devices are in Suspend, tap the power key to wake the FC300.Using the correct procedure, wake the targeted Bluetooth device if necessary.There may be audible or visual signals as both devices discover and pair with each other.Taskbar Connection IndicatorBluetooth module is connected to one or more of the targeted Bluetooth device(s).FC300 is not connected to any Bluetooth device.FC300 is ready to connect with any Bluetooth device.FC300 is out of range of all paired Bluetooth device(s). Connection is inactive.LED Connection IndicatorWhen the Bluetooth LED on the FC300 is off, Bluetooth hardware has been turned off or it does not exist inthe FC300.When the Bluetooth LED on the FC300 is on:●the FC300 is paired with another Bluetooth device but is out of range or not connected, or●is paired and connected to another Bluetooth device, or●is discovering other Bluetooth devices.The Bluetooth LED●Blinks slowly1when it is idle.●Blinks quickly2when the FC300 is discovering other Bluetooth devices.1Bluetooth LED is on for one second, off for five seconds2Bluetooth LED is on for 1/4 second, off for 2 seconds.3Bluetooth LED is on for 1/2 second, off for 1/2 secondWH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

Reboot 26●And blinks normally1when it is connected.There may be audible or visual signals from paired devices as they move back into range and re-connect withthe Bluetooth client in the FC300.RebootWhen the Windows CE desktop is displayed or an application begins, the power up (or reboot) sequence iscomplete.Warm BootStart | Warmbootor Start | Settings | Control Panel | Registry | Warmbootor Start | Run, type WARMBOOT and press EnterThe Warm Boot function refreshes the Windows operating system without clearing RAM or deleting installedprograms. FC300 user-set parameters are unchanged.Warmboot terminates an ActiveSync connection. The ActiveSync connection must be re-established afterthe warm boot.The WARMBOOT text command is not case-sensitive2.TroubleshootingCan’t change the date/time oradjust the volume.AppLock is installed and may be running in User Mode on the FC300.AppLock user mode restricts access to the control panels.Touchscreen is not acceptingstylus taps or needs recal-ibration.Press <Ctrl>+<Esc> to force the Start Menu to appear. Use the tab, back-tab and cursor keys to move the cursor from element to element.New FC300 main batteries don'tlast more than a few hours.New batteries must be fully charged prior to first use. Li-Ion batteries (likeall batteries) gradually lose their capacity over time (in a linear fashion)and never just stop working. This is important to remember – the FC300 isalways ‘on’ even when in the Suspend state and draws battery power atall times.1Bluetooth LED is on for 1/2 second, off for 1/2 second2The text typed in the text box can be upper or lower case or a combination of upper and lower case letters.FC300 User Guide WH-FC300USER-001For Review - Do Not Distribute - LXE Confidential

Regulatory Notices and Safety InformationRF NoticesWaste Electrical and Electronic Equipment (WEEE)Important:This symbol is placed on the product to remind users to dispose of Waste Electrical andElectronic Equipment (WEEE) appropriately, per Directive 2002-96-EC. In most areas, thisproduct can be recycled, reclaimed and re-used when properly discarded. Do not discard labeledunits with trash. For information about proper disposal, contact LXE through your local salesrepresentative, or visit www lxe com.Class B Digital DeviceNOTICEThis device complies with Part 15 of the FCC Rules [and with RSS-210 of Industry Canada]. Operation issubject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesiredoperation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to try to correct the interferenceby one or more of the following measures:●Reorient or relocate the receiving antenna.●Increase the separation between the equipment and the receiver.●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.●Consult the dealer or an experienced radio/TV technician for help.NOTICEChanges or modifications made to this equipment not expressly approved by LXE, Inc., may void the FCCauthorization to operate this equipment.Industry CanadaThis Class B digital apparatus meets all requirements of the Canadian Interference Causing EquipmentRegulations. Operation is subject to the following two conditions: (1) this device may not cause harmfulinterference, and (2) this device must accept any interference received, including interference that may causeundesired operation.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

RF Notices 28Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleurdu Canada. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limitesapplicables aux appareils numériques de Classe B prescrites dans le Règlement sur le brouillageradioélectrique édits par le ministère des Communications du Canada.Li-Ion BatteryWhen disposing of the FC300 main battery, the following precautions should be observed: The battery shouldbe disposed of properly. The battery should not be disassembled or crushed. The battery should not be heatedabove 212°F (100°C) or incinerated.NOTICE:This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe [*] est conforme á la norme NMB-003 du Canada.RF NoticesThis device contains transmitter Module FCC ID: KDZLXE4830PRF Safety Notice (Summit Client - 4830)Caution:This portable device with its antenna complies with FCC and Industry Canada RF exposure limitsset for an uncontrolled environment. This equipment has shown compliance with FCC andIndustry Canada Specific Absorption Rate (SAR) limits. Highest reported SAR for the FC300 isUnknown W/kg on body. Any accessories not provided by LXE should not be used with thisdevice. This device must not be co-located or operating in conjunction with any other antenna ortransmitter.This device contains transmitter Module FCC ID: KDZLXE4831PRF Safety Notice (Summit Client - 4831)Caution:This portable device with its antenna complies with FCC and Industry Canada RF exposure limitsset for an uncontrolled environment. This equipment has shown compliance with FCC andIndustry Canada Specific Absorption Rate (SAR) limits. Highest reported SAR for the FC300 isUnknown W/kg on body. Any accessories not provided by LXE should not be used with thisdevice. This device must not be co-located or operating in conjunction with any other antenna ortransmitter.R&TTE Directive Requirements (Applies only to equipment operated within the EU/EFTA)Information to UserA label on the exterior of the device should resemble one of the labels shown below (the labelcontains the LXE part number of the installed radio card). The labels shown below and affixed to thedevice, identify where the device may be used and where its use is restricted. Use of a device isprohibited in countries not listed below or otherwise identified by the label. (May or may not includethe 0560 Notified Body Number. Substitute 4 digit Notified Body Number may also be applied.)FC300 User Guide WH-FC300USER-001For Review - Do Not Distribute - LXE Confidential

29 AC Power Supply Safety StatementAC Power Supply Safety StatementThe LXE-approved AC Power Adapter is only intended for use in a 25ºC (77ºF) maximum ambienttemperature environment.FC300 : Output Rated 15VDC, 4A 60W.Optional A/C Power Supply: Outside North America, this unit is intended for use with an IEC certified ITEpower supply with output rated as stated at the top of this page. (US)Alimentation c.a. optionnelle: Hors de l’Amérique du Nord, cette unité est conçue pour être utilisée avec unealimentation ITE certifiée CEI de sortie nominale indiquée au haut de cette page. (FR)Valgfrit vekselstrømforsygning Udenfor Nord Amerika er denne enhed udstattet med en IEC (internationalelektronisk Kommission) udfærdiget med en ITE strømforsygning med strømudgang som fastslået på dennesides begyndelse. (DK)Vaihtoehtoinen vaihtovirran syöttölaite: Pohjois-Amerikan ulkopuolella tämä laite on tarkoitettu käytettäväksisellaisen IEC:n sertifioiman ITE-tehonsyöttölaitteen kanssa, jonka antoteho on tämän sivun yläosassaesitetyn mukainen. (FI)Optionales Netzteil (Wechselstrom) Außerhalb Nordamerikas sollte diese Einheit über ein der IEC-Normentsprechendes ITE-Netzteil gespeist werden, und zwar mit einer wie oben auf dieser Seite genanntenAusspeisung. (DE)Προαιρετική Τροφοδοσία Συνεχούς Ρεύματος Εκτός Β. Αμερικής, η μονάδα αυτή προορίζεται για χρήση μεένα τροφοδοτικό ITE πιστοποιημένο κατά IEC με ονομαστική ισχύ όπως δηλώνεται στην αρχή της σελίδας.(GR)Alimentazione opzionale a corrente alternata: Al di fuori dei paesi dell’America del nord, l’unità deve essereimpiegata con un dispositivo d’alimentazione per attrezzature informatiche approvato dalla IEC la cui potenzanominale sia pari a quella indicata all’inizio della pagina. (IT)Vekselstrømforsyning (ekstrautstyr): Utenfor Nord-Amerika skal dette produktet brukes med en IEC-sertifisert ITE-strømforsyning med klassifisert effekt som angitt øverst på denne siden. (NO)Fornecimento opcional de CA: Fora dos EUA, esta unidade destina-se a ser usada com dispositivos defornecimento de corrente ITE com certificação IEC, com a capacidade indicada no topo desta página. (PT)Suministro optativo de corriente alterna Fuera de América del Norte, esta unidad se debe utilizar con unalimentador ITE homologado por la IEC (comisión electrotécnica internacional) con una salida que tenga lacalificación que figura en la parte superior de esta página. (ES)Valfri A/C Strömförsörjning Utanför Nordamerika är det meningen att denna enheten används med en IEC-certifierad ITE-strömförsörjare med den uteffekt som anges längst uppe på den här sidan. (SE)İsteğe Bağlı A/C Güç Kaynağı: Kuzey Amerika dışında, bu ünite, çıkış sınıflandırması bu sayfanın başındabelirtilen IEC sertifikalı bir ITE güç kaynağı ile birlikte kullanılmak üzere tasarlanmıştır. (TR)Legend: Danish – DK; English – US; Finnish – FI; French- - FR; German – DE; Greek – GR; Italian – IT;Norwegian – NO; Portuguese – PT; Spanish – ES; Swedish – SE; Turkish – TR.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

30 Laser Light Safety StatementLaser Light Safety StatementWarning This product uses laser light. One of the following labels is provided on the scanner.Please read the Caution statement. (US)Mise én garde: Ce produit utilise un rayon laser. L’une des étiquettes suivantes est apposée sur le scanneur.Veuillez lire l’avertissement qu’elle contient. (FR)Advertência: Este produto usa luz de laser. O scanner contém um dos seguintes avisos. Favor ler o Aviso.(PT)Varning: Denna produkt använder laserljus. En av de nedanstående etiketterna sitter på scannern. Var god läsvarningstexten. (SE)Advarsel: Dette produkt anvender laserlys. En af følgende mærkater anvendes på scanneren. Læs venligstsikkerhedsforanstaltningen. (DK)Varoitus: Tämä tuote käyttää laservaloa. Skannerissa on jokin seuraavista tarroista. Lue Huomio-kohta. (FI)Warnung: Dieses Produkt verwendet Laserlicht. Eines der folgenden Etiketten befindet sich auf demScanner. Bitte lesen Sie den Gefahrenhinweis. (DE)Attenzione: Questo prodotto utilizza luce laser. Una delle etichette seguenti c’ ubicata sullo scanner. Siraccomanda di leggere con attenzione le avvertenze riportate. (IT)Advarsel: Dette utstyret bruker laserlys. En av følgende etiketter er plassert på scanneren. Les advarselen påetiketten. (NO)Advertencia: Este producto usa luz de láser. Las etiquetas se proveen en la máquina exploradora. Por favor,lea detenidamente la explicación para las precauciones. (ES)Waarschuwing: Dit product gebruikt laserlicht. Een van de volgende labels is op de scanner aangebracht.Lees a.u.b. de waarschuwing onder Oppassen. (NL)WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

Laser Light Safety Statement 31FC300 User Guide WH-FC300USER-001For Review - Do Not Distribute - LXE Confidential

32 Hazardous Locations WarningsHazardous Locations WarningsWARNINGDo not charge in hazardous area.WARNINGSeparate connectors only in non-hazardous area.WARNINGOnly use Itron 161888-0001 163086-0001 batteries as replacements.WARNINGEXPLOSION HAZARD. DO NOT DISCONNECT WHILE THE CIRCUIT IS LIVE ORUNLESS THE AREA IS KNOWN TO BE FREE OF IGNITABLE CONCENTRATIONS.WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

IndexAAC Power Scheme 20AC Power Supply Safety Statement 29Adjust Headset / Microphone and Secure Cable 14Adjust the Display Backlight Brightness 22Adjusting the Display Backlight Timer 22AppLock Switchpad 24Apply the Touchscreen Protective Film 23Assemblytethered scanner 15USB Host 9-11Attaching the Handstrap 16BBacklightKeypad 8BatteryInstall 4Remove 4Battery insert and remove instruction 4Battery Power Scheme 20Battery Status LED 7Bluetooth client functions 7Bluetooth connection 25Bluetooth LED 25Bluetooth LED activity 25Bluetooth Status LED 7CCalibrate the touchscreen 22Carry Case with Metal Snaps 17Class B 27Cleaning 23Client Cable Assembly 10WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

Index 34Connect or Remove the Battery Pack 4Connecting a Tethered Scanner 15Connecting an External Power Supply 12Connecting Cables 9Connecting the Headset Cable 13Connecting the Serial and Power Cable 11Connecting the USB Client and Power Cable 10Connecting the USB Host and Power Cable 9Connecting Vehicle Power 12Connection Indicators 25Cumulative mode timers 20DDate, Time, TimeZone18Daylight Savings location 18display backlight 22GGrab Time Utility 18HHandstrapassembly 16Hardware Setup 3Hazardous Locations Warnings and Information 32HeadsetAdjusting the microphone 14Mouthpiece Talk label 14quick connectcable14Hide input panel 19Hide online keyboard 19Host Cable Assembly 9Hotswap the Main Battery 5How To Index of Instructions 1FC300 User Guide WH-FC300USER-001For Review - Do Not Distribute - LXE Confidential

35 IndexIInput panel 19IntroductionMain 1KKeypad Backlight 8, 22Keypad Backlight Setting 8LLaser Light Safety Statement 30Laser Warnings and Labels 2LEDBattery Status 7Bluetooth 7System Status 7LEDs (Light Emitting Diodes) 7Mmain battery status 7PPower key 3power management status 7Protective film for touchscreen 23RReboot 26warm boot 26Recalibrate thetouchscreen22Remove Battery 4RF Notices 28WH-FC300USER-001 FC300 User GuideFor Review - Do Not Distribute - LXE Confidential

Index 36SSafety StatementAC Power Supply 29Serial and Power Cable 11Set Date and Time Zone 18Set Power Scheme Timers 20Set Speaker Volume 21Set Up A New Device 3SIP soft input panel 19Software Setup 3Status LEDs 7Stylushow to use 6Switchpad 24System Status LED 7TTethered scanner cable assembly 15Touchscreenand the stylus 6Touchscreen protective film 23Troubleshooting 26UUSB host cable assembly 9-11Using the AppLock Switchpad 24Vvirtual keyboard 19Volume adjust 21WWarm Boot 26WEEE 27FC300 User Guide WH-FC300USER-001For Review - Do Not Distribute - LXE Confidential

Navigation menu