Honeywell QC900A Bar Code Scanner with BT User Manual Reg 0002 Rev A cordless

Honeywell International Inc Bar Code Scanner with BT Reg 0002 Rev A cordless

Contents

User Manual Appendix

Reg-0002 Rev A
2/06
www.handheld.com
Reg-0002 Rev A
Agency Compliance Statements
This device meets or exceeds the requirements of all applicable standards organizations for safe operation. However, as with any electrical
equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow. Please read these guidelines
carefully before using your device.
Regulatory and Safety Approvals
FCC Class B Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio or television technician for help.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the
following booklet helpful: “Something About Interference.” This is available at FCC local regional offices. Hand Held Products, Inc. is not
responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of
connecting cables and equipment other than those specified by Hand Held Products, Inc. The correction is the responsibility of the user. Use
only shielded data cables with this system.
In accordance with FCC 15.21, changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To
maintain compliance with FCC RF exposure guidelines for body-worn operation, do not use accessories that contain metallic
components and ensure that the device is at least 15mm (0.6 inches) from the body.
Canadian Compliance
This Class B digital apparatus compiles with Canadian ICES-003. Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
3. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide max-
imum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
The CE mark on the product indicates that the system has been tested to and conforms with the provisions noted within the 89/336/EEC
Electromagnetic Compatibility Directive and the 73/23/EEC Low Voltage Directive.
For further information please contact:
Hand Held Products, Inc.
Nijverheidsweg 9
5627 BT Eindhoven
The Netherlands
Hand Held Products shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked
and does not comply with the Low Voltage Directive.
Bluetooth Qualified Product
Bluetooth Qualified Body approved as a Bluetooth Class II radio.
Parameter Specification
USA FCC Part 15, Class B
Canada ICES-003
European Community
EN55022 (CISPR 22) Class B
EN55024:1998
EN60950
EN60825-1
!
Reg-0002 Rev A
2/06
www.handheld.com
This product is marked with in accordance with the Class II product requirements specified in the R&TTE Directive, 1999/5/EC.
The equipment is intended for use throughout the European Community.
LED Safety Statement
This device has been tested in accordance with IEC60825-1 LED safety, and has been certified to be under the limits of a Class 1 LED device.
Laser Eye Safety Statement
If the following label is attached to your product, it indicates the product contains a laser engine or laser aimer:
UL and cUL Statement
UL and cUL listed: UL60950-1 and CSA C22.2 No.60950-1-03.
C-Tick Statement
Conforms to AUS/NZ 3548.
TÜV Statement
TÜV or GS marked to EN60950 and EN60825-1.
Mexico
Certified.
Solids and Water Protection
This device has a rating of IP41, immunity of foreign particles and dripping water.
Patents
Please refer to product packaging for patent information.
For European Community Users
Hand Held Products complies with Directive 2002/69/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on
waste electrical and electronic equipment (WEEE).
Waste Electrical and Electronic Equipment Information
This product has required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact
health and the environment, if not properly disposed.In order to avoid the dissemination of those substances in our environment and to diminish
the pressure on the natural resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will
reuse or recycle most of the materials of the product you are disposing in a sound way.
If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration.
You may also contact your supplier for more information on the environmental performances of this product.
The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal waste and invites you
to use the appropriate separate take-back systems for product disposal.
Regulatory Approvals for Bluetooth Radio Devices
RF devices are designed to comply with the most current applicable
standards on safe levels of RF energy developed by the Institute of
Electrical and Electronics Engineers (IEEE) and the American
National Standards Institute (ANSI) and have been recommended for
adoption by the Federal Communications Commission (FCC).
RF Approvals Specification
USA FCC Part 15.247
Canada RSS 210
Bluetooth Radio Device R&TTE Compliance
Statement
This device is in conformity with all essential requirements of the
R&TTE Directive (1999/5/EC). This equipment has been
assessed to the following standards:
Parameter Specification
RT&TTE
EN300 328-2:2000
EN301 489-1 (2002-08)
EN301 489-17 (2002-08)
EN60950:2000
This device has been tested in accordance with and complies with IEC60825-1: 1993+A1+A2
and 21 CFR 1040.10 and 1040.11, except for deviations pursuant to Laser Notice No. 50, dated
July 26, 2001.
LASER LIGHT, DO NOT STARE INTO BEAM, CLASS 2 LASER PRODUCT, 1.0 mW MAX
OUTPUT: 650nM.
Caution: Use of controls or adjustments or performance of procedures other than those
specified in the user documentation may result in hazardous radiation
exposure.

Navigation menu