Honeywell VM3WWANA Vehicle Mount Computer User Manual VM3 W7 UG

Honeywell International Inc Vehicle Mount Computer VM3 W7 UG

UserManual.wiki >

Honeywell >

VM3WWANA User Manual >

User manual_2

5 - 13Bar Code ReadersThe Thor VM3 can use the following external bar code readers:• Tethered hand-held scanners are tethered to a serial port or a USB host port (via a dongle cable) on the Thor VM3 Quick Mount Smart Dock and are configured by scanning the engine-specific bar codes in the scanner manufacturer's programming guide. The manufacturer's guides are usually shipped with the bar code reader.• Wireless hand-held Bluetooth scanners are configured by scanning the engine-specific bar codes in the scanner manufacturer's programming guide. The manufacturer's guides are usually shipped with the bar code reader. • The body worn Bluetooth Ring Scanner module may be using a Symbol 4400 Ring Imager or a Symbol 955 Ring Scanner. The BTRS module is configured by scanning the bar codes in the Bluetooth Ring Scanner Guide.Scanner WedgeHoneywell provides Freefloat Link*One for bar code decoding needs on the Thor VM3. Refer to the Freefloat website for documentation on Freefloat Link*One.Touch Screen CalibrationStart > Programs > PenMount Windows Universal DriverTo calibrate the touch screen, tap Start > Programs > PenMount Universal Driver > Utility > PenMount Control Panel. Select PenMount 6000 USB and then tap Configure. Select Standard Calibration or Advance Calibration.Advanced Calibration allows the user to select the number of calibration points. With either option, follow the on screen instructions to touch the red square, hold the touch and then lift the stylus to complete the calibration process.

5 - 14BIOSThe Microsoft Windows operating system is installed before shipping. The default BIOS parameters are configured at that time. In most cases, it is unnecessary to modify the BIOS parameters.Generally, it is only necessary to enter the BIOS setup to change the boot order of the drives.This section is not intended to detail all features of the BIOS, instead it is intended to cover the most commonly used setup options.Accessing the BIOS SetupWhen the Embedded BIOS screen (Phoenix Technologies) is displayed press the Del key to enter BIOS setup.Use the arrow keys to move around the screen.To access and modify the BIOS on the Thor VM3, an external keyboard must be attached.Boot OrderTo view or edit the boot order, select the Boot tab.By default, the first device in the boot order is USB Hard Drive.The second device is the Windows CE Image.Exiting BIOS SetupTo exit the BIOS setup, select the Exit tab and select one of these options:• Save Setting and Restart• Exit Setup without Saving Changes• Reload Factory-Defaults and RestartThor VM3 Recovery DVDA recovery DVD is available to restore the operating system on your Thor VM3 to the same state it had when it was shipped from the factory. The recovery DVD may not reload all factory installed software.Contact Technical Assistance (page 9-1) for information on the recovery DVD and for assistance installing other factory loaded software.•CAUTION - Be very careful when using this utility to modify BIOS Setup parameters. The Thor VM3 may generate unex-pected results when incorrect or conflicting parameter values are entered. Selecting incorrect or invalid options may re-quire the Thor VM3 to be returned for repairs.The parameters should only be modified by Information Services personnel or the system administrator.If a USB drive, such as a thumb drive is attached to the Thor VM3, the device attempts to boot from the USB drive:• If the USB drive contains a bootable sector, the Thor VM3 boots from the USB drive.• If the USB drive does not contain a bootable sector, the Thor VM3 does not boot. Remove the USB drive and boot the Thor VM3 again.!!

5 - 15Windows Embedded Standard 20091. Locate the CCU icon either on the desktop or by selecting 2. Double-tap the icon to launch the CCU.Windows Embedded Standard 7 and Windows 7 Professional:3.4.Using Configuration Cloning Utility GUI

6 - 7It is important the Radio Mode parameter correspond to the AP to which the device is to connect. For example, if this parameter is set to G rates only, the Thor VM3 may only connect to APs set for G rates and not those set for B and G rates.Encryption None Type of encryption to be used to protect transmitted data. Available options may vary by SCU version.Options are: None, WEP (or Manual WEP), WEP EAP (or Auto WEP), WPA PSK, WPA TKIP, WPA CCKM, WPA2 PSK, WPA2 AES, or WPA2 CCKM.CKIP is not supported in the Thor VM3.Note: The Encryption type chosen determines if the WEP Keys / PSK Keys button is active and also determines the available entries in the WEP or PSK pop-up window.Radio Mode BGA Rates Full Specify 802.11a, 802.11b and/or 802.11g rates when communicating with the AP. The options displayed for this parameter depend on the type of radio in-stalled in the mobile device. Options:B rates only (1, 2, 5.5 and 11 Mbps)BG Rates Full (All B and G rates)G rates only (6, 9, 12, 18, 24, 36, 48 and 54 Mbps)BG optimized or BG subset (1, 2, 5.5, 6, 11, 24, 36 and 54 Mbps) A rates only (6, 9, 12, 18, 24, 36, 48 and 54 Mbps)ABG Rates Full (All A rates and all B and G rates with A rates preferred)BGA Rates Full (All B and G rates and all A rates with B and G rates preferred)Ad Hoc (when connecting to another client device instead of an AP)Default:BGA Rates FullParameter Default Explanation

$6 - 10GlobalStart > All Programs > Summit > Summit Client Utility > Global tabThe parameters on this panel can only be changed when an with a password. The current values for the parameters can be viewed by the general user without requiring a password.Note: Tap the Commit button to save changes. If the panel is exited before tapping the Commit button, changes are not saved!Factory Default SettingsRoam Trigger -65 dBmRoam Delta 5 dBmRoam Period 10 sec.BG Channel Set Full DFS Channels OffDFS Scan Time 120 ms.Ad Hoc Channel 1Aggressive Scan OnCCX Features OptimizedWMM OnAuth Server Type 1TTLS Inner Method Auto-EAPPMK Caching StandardWAPI Off (dimmed)TX Diversity OnRX Diversity On Start on MainFrag Threshold 2346RTS Threshold 2347LED OffTray Icon On Hide Passwords OnAdmin Password SUMMIT (or blank)Auth Timeout 8 secondsCerts Path C:\Program Files\Summit\certsPing Payload 32 bytesPing Timeout 5000 msPing Delay ms 1000 msLogon Options Use SCU credentials$

$6 - 13Note: Tap the Commit button to save changes. If this panel is closed before tapping the Commit button, changes are not saved!Logon OptionsThere are two options available, a Single Signon (page 6-14) option which uses the Windows username and password as the credentials for 802.1x authentication and a Pre-Logon Connection (page 6-14) option which uses saved creden-tials for 802.1x authentication before Windows logon.RTS Thresh 2347 If the packet size exceeds the specified number of bytes set in the Re-quest to Send (RTS) threshold, an RTS is sent before sending the pack-et. A low RTS threshold setting can be useful in areas where many client devices are associating with the Access Point. This parameter cannot be changed.LED Off The LED on the wireless card is not visible to the user when the wireless card is installed in a sealed mobile device. Options are: On, Off. Tray Icon On Determines if the Summit icon is displayed in the System tray.Options are: On, OffThe tray icon is not displayed when the Thor VM3 is running a Windows Embedded Standard 2009 operating system.Hide Password On When On, the Summit Config Utility masks passwords (characters on the screen are displayed as an *) as they are typed and when they are viewed. When Off, password characters are not masked.Options are: On, Off.Admin Password SUMMIT(or Blank) A string of up to 64 alphanumeric characters that must be entered when the Admin Login button is tapped. If Hide Password is On, the password is masked when typed in the Admin Password Entry dialog box. The password is case sensitive. This value is masked when the Admin is logged out.Options are: none.Auth Timeout 8 seconds Specifies the number of seconds the Summit software waits for an EAP authentication request to succeed or fail.If the authentication credentials are stored in the active profile and the authentication times out, the association fails. No error message or prompting for corrected credentials is displayed.If the authentication credentials are not stored in the active profile and the authentication times out, the user is again prompted to enter the cre-dentials.Options are: An integer from 3 to 60.Certs Path certificates A valid directory path, of up to 64 characters, where WPA Certificate Au-thority and User Certificates are stored on the mobile device when not using the Windows certificates store. Ensure the Windows folder path ex-ists before assigning the path in this parameter. See Certificates (page 6-32) for instructions on obtaining CA and User Certificates. This value is masked when the Admin is logged out.Options are: none.The complete path is C:\Program Files\Summit\certsPing Payload 32 bytes Maximum amount of data to be transmitted on a ping. Options are: 32 bytes, 64, 128, 256, 512, or 1024 bytes.Ping Timeout ms 5000 The amount of time, in milliseconds, that a device will be continuously pinged. The Stop Ping button can be tapped to end the ping process ahead of the ping timeout. Options are: Any number between 0 and 30000 ms.Ping Delay ms 1000 The amount of time, in milliseconds, between each ping after a Start Ping button tap. Options are: Any number between 0 and 30000 ms.Logon Options SCU Use SCU or Windows login credentials.Parameter Default Function$

$6 - 17Windows Certificate Store vs. Certs PathNote: It is important that all dates are correct on the Thor VM3 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail.User CertificatesEAP-TLS authentication requires a user certificate. The user certificate must be stored in the Windows certificate store.• To generate the user certificate, see Generate a User Certificate (page 6-35).• To import the user certificate into the Windows certificate store, see Install a User Certificate (page 6-37).• A Root CA certificate is also needed. Refer to the section below.Root CA CertificatesRoot CA certificates are required for EAP/TLS, PEAP/GTC and PEAP/MSCHAP. Two options are offered for storing these certificates. They may be imported into the Windows certificate store or copied into the Certs Path directory.Certs Path1. See Generate a Root CA Certificate (page 6-32) and follow the instructions to download the Root Certificate to a PC.2. Copy the certificate to specified directory on the mobile device. The default location for Certs Path is C:\Program Files\Summit\certs. A different location may be specified by using the Certs Path global variable. 3. When completing the Credentials screen for the desired authentication, do not check the Use MS store checkbox after checking the Validate server checkbox.4. Enter the certificate name in the CA Cert text box.5. Click OK to exit the Credentials screen and then Commit to save the profile changes.Windows Certificate Store1. See Generate a Root CA Certificate (page 6-32) and follow the instructions to download the Root Certificate to a PC.2. To import the certificate into the Windows store, See Install a Root CA Certificate (page 6-34).3. When completing the Credentials screen for the desired authentication, be sure to check the Use MS store check-box after checking the Validate server checkbox.4. The default is to use all certificates in the store. If this is OK, skip to the last step.5. Otherwise, to select a specific certificate click on the Browse (…) button. If using the Windows Certificate Store, the Windows Account must have a password. The password cannot be left blank. The Summit Client Utility uses the Windows user account credentials to access the Certificate Store. The Windows user account credentials need not be the same as the credentials entered in the Summit Client Utility.!$

$6 - 21LEAPTo use LEAP (without WPA, also called WEP-LEAP), make sure the following profile options are used.1. Enter the SSID of the Access Point assigned to this profile2. Set EAP Type to LEAP3. Set Encryption to WEP EAP or Auto WEP (depending on SCU version)4. Set Auth Type as follows:5. If the Cisco/CCX certified AP is configured for open authentication, set the Auth Type radio parameter to Open.6. If the AP is configured to use shared key or passphrase, set the Auth Type radio parameter to Shared.7. If the AP is configured for network EAP only, set the Auth Type radio parameter to LEAP.See Sign-On vs. Stored Credentials (page 6-15) for information on entering credentials.To use Stored Credentials, click on the Credentials button. No entries are necessary for Sign-On Credentials as the user will be prompted for the Username and Password when connecting to the network. Enter the Domain\Username (if the Domain is required), otherwise enter the Username.Enter the password. Click OK then click Commit.Ensure the correct Active Profile is selected on the Main tab and restart. The SCU Main tab shows the device is associated after the radio connects to the network.$

$6 - 22PEAP/MSCHAPTo use PEAP/MSCHAP, make sure the following profile options are used.1. Enter the SSID of the Access Point assigned to this profile2. Set EAP Type to PEAP-MSCHAP3. Set Encryption to WPA TKIP4. Set Auth Type to OpenTo use another encryption type, select WPA CCKM, WPA2 AES or WPA2 CCKM for encryption and complete other entries as detailed in this section.See Sign-On vs. Stored Credentials (page 6-15) for information on entering credentials.Click the Credentials button.• No entries except the CA Certificate Filename are necessary for Sign-On Credentials as the user will be prompted for the User Name and Password when connecting to the network.• For Stored Credentials, User, Password and the CA Certificate Filename must be entered.Enter these items as directed below.Enter the Domain\Username (if the Domain is required), otherwise enter the Username.Enter the password.Leave the CA Certificate File Name blank for now.Click OK then click Commit. Ensure the correct Active profile is selected on the Main tab.See Windows Certificate Store vs. Certs Path (page 6-17) for more information on certificate storage.Once successfully authenticated, import the CA certificate into the Windows certificate store. Return to the Credentials screen and check the Validate server checkbox.$

$6 - 24PEAP/GTCTo use PEAP/GTC, make sure the following profile options are used.1. Enter the SSID of the Access Point assigned to this profile2. Set EAP Type to PEAP-GTC3. Set Encryption to WPA TKIP4. Set Auth Type to OpenTo use another encryption type, select WPA CCKM, WPA2 AES or WPA2 CCKM for encryption and complete other entries as detailed in this section.See Sign-On vs. Stored Credentials (page 6-15) for information on entering credentials.Click the Credentials button.• No entries except the CA Certificate Filename are necessary for Sign-On Credentials as the user will be prompted for the User Name and Password when connecting to the network. Enter these items as directed below.Enter the Domain\Username (if the Domain is required), otherwise enter the Username.Enter the password.Leave the CA Certificate File Name blank for now.Click OK then click Commit. Ensure the correct Active Profile is selected on the Main tab.See Windows Certificate Store vs. Certs Path (page 6-17) for more information on certificate storage.Once successfully authenticated, import the CA certificate into the Windows certificate store. Return to the Credentials screen and check the Validate server checkbox. Note: Some servers may be configured to allow only a single use of the password for PEAP/GTC. In this case, wait for the token to update with a new password before attempting to validate the server. Then enter the new password, check the Validate Server checkbox and proceed with the certificate process below.$

$6 - 26WPA/LEAPTo use WPA/LEAP, make sure the following profile options are used.1. Enter the SSID of the Access Point assigned to this profile2. Set EAP Type to LEAP3. Set Encryption to WPA TKIP4. Set Auth Type as follows:5. If the Cisco/CCX certified AP is configured for open authentication, set the Auth Type radio parameter to Open.6. If the AP is configured to use shared key or passphrase, set the Auth Type radio parameter to Shared.7. If the AP is configured for network EAP only, set the Auth Type radio parameter to LEAP.To use another encryption type, select WPA CCKM, WPA2 AES or WPA2 CCKM for encryption and complete other entries as detailed in this section.See Sign-On vs. Stored Credentials (page 6-15) for information on entering credentials.To use Stored Credentials, click on the Credentials button. No entries are necessary for Sign-On Credentials as the user will be prompted for the Username and Password when connecting to the network. Enter the Domain\Username (if the Domain is required), otherwise enter the Username.Enter the password.Click OK then click the Commit button. Ensure the correct Active Profile is selected on the Main tab and restart. The SCU Main tab shows the device is associated after the radio connects to the network.$

$6 - 28• Enter the Domain\Username (if the Domain is required), otherwise enter the Username. • Enter the password.To use Automatic PAC Provisioning:• No additional entries are required.To use manual PAC Provisioning:• Enter the PAC Filename and PAC Password.• The PAC file must be copied to the directory specified in the Certs Path global variable. The PAC file must not be read only.Ensure the correct Active Profile is selected on the Main tab and restart. The SCU Main tab shows the device is associated after the radio connects to the network.Note: When using Automatic PAC Provisioning, once authenticated, there is a file stored in the C:\Program Files\Summit\certs directory with the PAC credentials. If the username is changed, that file must be deleted. The filename is autoP.00.pac.$

$6 - 29EAP-TLSTo use EAP-TLS, make sure the following profile options are used.1. Enter the SSID of the Access Point assigned to this profile2. Set EAP Type to EAP-TLS3. Set Encryption to WPA TKIP4. Set Auth Type to OpenTo use another encryption type, select WPA CCKM, WPA2 AES or WPA2 CCKM for encryption and complete other entries as detailed in this section.See Sign-On vs. Stored Credentials (page 6-15) for information on entering credentials.Click the Credentials button.• No entries except the User Certificate Filename and the CA Certificate Filename are necessary for Sign-On Credentials as the user will be prompted for the User Name when connecting to the network. • For Stored Credentials, User Certificate Filename and the CA Certificate Filename must be entered.Enter these items as directed below.Enter the Domain\Username (if the Domain is required), otherwise enter the Username.Select a user certificate from the Windows certificate store. Use the Browse button to locate the User Cert from the certifi-cate store. Highlight the desired certificate and press the Select button. The name of the certificate is displayed in the User Cert box.Some versions of the SCU require a User Cert password. If this entry field is present, enter the password for the user certif-icate in the User Cert pwd box.If there are no user certificates in the Windows certificate store, follow these instructions for Generate a User Certificate (page 6-35) and Install a User Certificate (page 6-37).See Windows Certificate Store vs. Certs Path (page 6-17) for more information on CA certificate storage.Check the Validate server checkbox.$

6 - 32CertificatesNote: Please refer to the Security Primer to prepare the Authentication Server and Access Point for communication.Note: It is important that all dates are correct on the Thor VM3 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail.Quick StartRoot Certificates are necessary for EAP-TLS, PEAP/GTC and PEAP/MSCHAP.1. Generate a Root CA Certificate (page 6-32) either from the Thor VM3 or using a PC.2. If a PC was used to request the certificate, copy the certificate to the Thor VM3.3. Install a Root CA Certificate (page 6-34).User Certificates are necessary for EAP-TLS1. Generate a User Certificate (page 6-35)either from the Thor VM3 or using a PC.2. If a PC was used to request the certificate, copy the certificate to the Thor VM3.3. Install a User Certificate (page 6-37).Generate a Root CA CertificateNote: It is important that all dates are correct on the Thor VM3 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail.The easiest way to get the root CA certificate is to use a browser on a PC or the Thor VM3 to navigate to the Certificate Authority. To request the root CA certificate, open a browser to http://<CA IP address>/certsrv. Sign into the CA with any valid username and password.If using the Windows Certificate Store, the Windows Account must have a password. The password cannot be left blank. The Summit Client Utility uses the Windows user account credentials to access the Certificate Store. The Windows user account credentials need not be the same as the entered in the Summit Client Utility.!

6 - 33Click the Download a CA certificate, certificate chain or CRL link. Make sure the correct root CA certificate is selected in the list box.Click the DER button.To download the CA certificate, click on the Download CA certificate link.

$6 - 34Click the Save button and save the certificate. Make sure to keep track of the name and location of the certificate.Next install the certificate on the Thor VM3.Install a Root CA CertificateNote: This section is only if the Windows certificate store is used. If the certificate store is not used, copy the certificate to the C:\Program Files\Summit\certs folder or other path specified in the Summit Certs global parameter.Copy the certificate file to theThor VM3. The certificate file has a .CER extension. Locate the file and double-tap on it. If presented with a security warning, confirm that you want to open the file.If the Certificate Wizard does not start automatically when you double-tap the certificate .CER file:1. Select Start > Run and type certmgr.msc in the text box and tap OK (Windows Embedded Standard 2009 only).2. In the left pane, right-click Trusted Root Certificate Authorities and select All Tasks > Import.3. The Certificate Import Wizard starts.4. Tap Next and use the Browse.. button to locate the Root certificate copied to the Thor VM3 then tap Open.5. The certificate filename and path are displayed. Tap Next.Tap the Install Certificate button.The certificate import wizard starts. Tap Next.$

6 - 35Generate a User CertificateThe easiest way to get the user certificate is to use the browser on the Thor VM3 or a PC to navigate to the Certificate Authority. To request the user certificate, open a browser to http://<CA IP address>/certsrv. Sign into the CA with the username and password of the person who will be logging into the mobile device.This process saves a user certificate file. There is no separate private key file as used on Windows CE devices.Click the Request a certificate link. Click on the User Certificate link.

6 - 36Click on the Submit button. if there is a message box asking if you want to confirm the request, click Yes.The User Certificate is issued.Install the user certificate on the requesting computer by clicking the Install this certificate link. If the requesting computer is the Thor VM3, then the process is finished. otherwise, export the certificate as described below.Exporting a User CertificateSelect Tools > Internet Options > Content and click the Certificates button.Make sure the Personal tab is selected. Highlight the certificate and click the Export button.The Certificate Export Wizard is startedSelect Yes, export the private key and click Next.

6 - 37Click Finish. and OK to close the Successful Export message.Locate the User Certificate in the specified location. Copy to the Thor VM3. Install the User certificate.Install a User CertificateAfter generating and exporting the user certificate, install the user certificate.1. Copy the certificate from the PC to the Thor VM3. 2. Locate the certificate file (it has a .PFX extension) and double-click on it. If clicking on the certificate file does not launch the certificate import wizard, follow the Manually Initiate Certificate Installation (page 6-38) before continuing the instructions below.3. The certificate import wizard starts. Tap Next.4. Confirm the certificate file name and location.5. Tap Next.6. You are prompted for the password that was assigned when the certificate was exported.7. It is not necessary to select either of the checkboxes displayed above.8. Enter the password and tap Next.9. On the next screen, allow Windows to automatically select the certificate store, then click Next and Finish. An import successful message is displayed.Uncheck Enable strong protection and check Next. The certifi-cate type must be PKCS #12 (.PFX).When the private key is exported, you must enter the password, confirm the password and click Next. Be sure to remember the password as it is needed when installing the certificate.Supply the file name for the certificate. Use the Browse button to select the folder where you wish to store the certificate. The certif-icate is saved with a .PFX extension.

6 - 38Manually Initiate Certificate InstallationIf the Certificate Wizard does not start automatically when you double-tap the certificate .PFX file:1. Select Start > Run and type certmgr.msc in the text box and tap OK.2. In the left pane, right-click Personal and select All Tasks > Import.3. The Certificate Import Wizard starts.4. Tap Next and use the Browse.. button to locate the User certificate copied to the Thor VM3. If necessary, change the file type drop down list at the bottom of the explorer window from *.cer to *.pfx. After selecting the .PFX file, tap Open.5. The certificate filename and path are displayed. Tap Next.6. Return to the installation instructions above.

6 - 39OneClick InternetThis section contains the User Manual for the customized version of WebToGo's OneClick Internet for the Honeywell Thor VM3.OneClick Internet is installed by Honeywell on all Thor VM3s equipped with a WWAN radio. Available carriers and OneClick fea-tures may vary by device.OneClick Internet provides:• Internet connection management• Email download• SMS Management• Contact management for SIM and Microsoft Outlook• GPS ManagementSince WebToGo OneClick Internet is preinstalled, it is present on the Windows Start Menu. A desktop icon is also provided.Preparing for Initial Use on the Thor VM3Install SIM CardIf using a CDMA carrier such as Verizon, skip this step because a SIM card is not used.Install SIM Card (page 4-57) in the Thor VM3.Load FirmwareWhile the OneClick Internet utility is preinstalled, it is necessary to load the GOBI radio firmware for your selected car-rier such as AT&T, T-Mobile or Verizon.Note: For carriers requiring a SIM card, the firmware may automatically be selected when a SIM card is installed in the Thor VM3.Double-tap the OneClick Internet icon on the Thor VM3 desktop.Tap t h e Settings button and select the Firmware tab. Select the firmware for your carrier from the list and tap Change.For more details, see OneClick Internet Connection Manager (page 6-56) and the Firmware (page 6-48) tab.ActivationThis step is only necessary for Verizon.You need the IMEI number for the Thor VM3 when you contact Verizon prior to activating service on the Thor VM3. The IMEI number can be found on the Info (page 6-48) tab.The activation screen is displayed automatically after the Verizon firmware is selected. If the activation screen is not automatically displayed, double-tap the OneClick Internet icon on the desktop. Select Settings > General tab and tap the Activate button.Honeywell does not recommend using standby on the Thor VM3 while the WWAN connection is active. When exiting standby, a delay of one minute or more may occur as the WWAN radio reads firmware files and initializes before recon-necting. If this delay is acceptable to the user, standby may be enabled.When the One Click Internet utility is displayed on screen and the Thor VM3 enters standby, the touch screen may remain inactive for 10-15 seconds after the Thor VM3 resumes from standby.!

6 - 40Make sure Automated Activation is selected and tap Next.Tap Next to complete the activation.Once the activation is completed, OneClick Internet may be minimized to the tray. To verify your settings, tap on the OneClick Internet icon in the system tray.Tap Settings. Tap the Network tab.

6 - 42Menu ButtonsRadio Button The Radio button allows you to switch the WWAN radio on and off to save power or to disable the radio in instances where it is not desired (such as during airplane travel).When the radio is switched off, the button is red. When on, it is green. If the radio is disabled by a hardware switch or if the device is not available, the button is disabled and is light gray/white.Statistics Button The Statistics area provides advanced information about the connection. Values displayed are approximate.Tap the Statistics button to enable the statistics viewing area, which is below the main area. When the statistics are displayed, tapping the Statistics button again hides the statistics viewing area.Update Button OneClick Internet provides a built-in online update functionality that allows for an automatic update of OneClick Internet application, device drivers, and APN database.Honeywell DOES NOT recommend using this option. Contact Technical Assistance (page 9-1) or information on upgrading to another version of OneClick Internet.The update is triggered by pressing the update button. The application will check the WebToGo server, if updates are available, and offer them for download if suitable.In order to start the update, select a file from the list of available updates and tap OK.Help Button OneClick Internet includes online help that can be accessed by tapping the Help button.Data In: The amount of data received during the current connection.Data Out: The amount of data sent during the current connection. Total: The total amount of data transferred during the current connection.Speed: The current data transfer rate.Max. Speed: The maximum data transfer rate during this connection.Time: The duration of the current connection.

6 - 45NetworkThe appearance of the network tab depends on the type of firmware selected.Network with SIM CardSelect ConnectionSelect and tap Apply. A “Network changed successfully” message is displayed.Close the tab and view the signal strength icon in the main window. Once the signal strength is displayed, you can establish a connection.Select NetworkUse this option to select from available networks.Note: When you are registered to a CDMA network, you cannot select the network. “All CDMA network” is shown instead.Note: The network list only appears if the connection setting is Only use GPRS or Only use UMTS/HSPA.Select the network and tap on the register button. If the change is successful you will see the message “Network changed successfully”.This item is useful when traveling . Automatic mode selects the preferred network of your network opera-tor.If enabled, Network Selection displays a list of network options.1. Automatic Selection2. Retrieving Networks..The currently registered network is marked.Label DescriptionSelect automatically Selects the best suited network automaticallyUse GPRS/EDGE only Use only GPRS/EDGE for a connectionUse UMTS/HSPA only Use only UMTS/HSPA for a connection.

6 - 46CDMA NetworkInformation on the CDMA network is displayed. There are no editable parameters on this screen.HistoryThe history shows the data volume transferred in a specified time frame. Select the From and To dates to see the data volume sent/received in the specified period. Tap Reset to reset the counter.

6 - 47PINYou can Activate/Deactivate the PIN or Change the PIN.Activate/Deactivate PINThis tab is only displayed when a firmware is loaded that requires a SIM card (such as AT&T or T-Mobile).By default, you have to enter the PIN each time you start WebToGo OneClick Internet using a modem card. Deactivate the PIN to avoid entering the PIN each time.Change PINThis dialog lets you change your PIN.Label Description Current PIN Enter the current PIN. New PIN Enter the new PIN. Verify PIN Verify the new PIN by entering it again.

6 - 50ApplicationUse the Application tab to specify any application to launch automatically once the Internet connection is estab-lished. Use the Browse button to locate the desired application.Application ButtonsSMSGobi NDIS Auto Connect When selected OneClick Internet connects automatically after powering up the operating system and before the user logs in.Label Description

6 - 51The SMS Center window is split into menu bar, folder view, folder content and preview window. To manage your short messages you may: FolderBy using this menu, you may change the folder structure of the SMS Center:Button DescriptionManage SMS foldersChange SMS settingsCreate new SMS/MMS messagesReply to SMSForward SMSMove SMS to a folderDelete SMSSend and receive SMS/MMS (if supported)Manage phone book contacts on SIM and in Email client.

6 - 52Note: Predefined folders can't be deleted or modified.SettingsThe settings window lets you change the deletion mode. You may choose whether to delete an SMS from the SMS Center, from the SIM or decide whether this should be asked at all. You may also activate an alarm signal when a new SMS arrives.New SMSThe “New Message” window is used to enter the SMS text. You may also enter texts by copy & paste from other applications. The status bar at the lower right corner indicates the length of the SMS for your convenience: the first number tells you how many parts the SMS consists of (one part has max. 160 characters/unicode70), the second number counts down from 160/70 characters. The number in parenthesis () counts the total number of characters. The recipient for your SMS has to be entered in the “To” field. This can be either entered by typing digits or by clicking the “To” button to select a recipient from the address book. Recipient addresses may be taken from the SIM address book or from your Email client's contact folder. Just select an address and click OK. To send the mes-sage click “Send/Receive”.ReplyHighlight a message to which you want to reply, e.g. in the inbox folder, then click the “Reply” button. The “New Message” window opens and the recipient address is already filled in the “To” field. Continue as before when sending a new message.ForwardHighlight a SMS, which you want to forward. Click the “Forward” button. The “New Message” window opens, how-ever the message text is already copied. Continue as before when sending a new message.Move SMS..Highlight the SMS to be moved and click the “Move SMS” button. A small window opens that lets you select the destination folder. Select the folder to which the message should be moved, then click “Move”.DeleteHighlight the SMS which you want to delete. Click “Delete” to remove the message.Send/ReceiveMessages will be sent and/or received by clicking on this button.Button DescriptionNew Folder Creates a new folder, name has to be uniqueRename Renames an existing folderRemove Removes an existing folder (including the messages)

6 - 53AddressesClicking this button opens the address book. You may add new contacts to your personal address book or you may change existing addresses, delete addresses or exchange them with your SIM card and your Email client applica-tion, or export the data set. Web BrowserClicking this button opens the Web Browser and allows the user to surf the Internet once the connection is established. The default browser is used, which is Internet Explorer by default on the Thor VM3.EmailClicking this button opens the Email application after the connection is established. The Email application is the default Email client set in the Control Panel (Start > Control Panel > Internet Options > Programs tab).GPSTap the GPS button to open the GPS window. Press Get GPS to start the GPS. The rotating GPS button indicates the GPS is active.Buttons DescriptionNew Contact Create new contact.Modify Modify a contact.Delete Delete contacts, mark one or more and press the button.Copy Synchronization with MS Outlook.Export To export addresses you may select between two export formats:• CSV (comma separated text format, usually read by spread sheet applications) • VCard (business card format, used by MS Outlook and other applications)

6 - 54After Latitude and Longitude Data are displayed, the user can tap Track Me to open Google Maps, showing their cur-rent location on a map.Lat - Latitude - The location north or south of the equator in degrees.Lon - Longitude: The angular distance from the Prime Meridian in degrees.After Latitude and Longitude Data are displayed, the user can tap Clipboard and the latitude and longitude are copied to the clipboard cache. The data can be pasted into an email, document or other electronic media.AboutOneClick Internet allows the user to configure the WWAN connection by entering basic setup information. The network connection (service carrier) can be chosen based on the firmware loaded, GPS tracking can be enabled and SMS messaging can be configured.Once configured, OneClick Internet allows the user to connect or disconnect from the mobile network. System RequirementsOneClick Internet requires:• Gobi 000 3G Module (preinstalled by Honeywell)• Gobi 000 Driver package (loaded by Honeywell)OneClick Internet for Gobi 000is compatible with the following operating system on the Thor VM3:• Windows Embedded Standard 2009 Supported LanguagesOneClick Internet supports the following languages:German, English, Spanish, French, Polish, Russian, Italian, Simplified Chinese and Traditional Chinese.Note: This does not mean that the Thor VM3 has been localized for these languages.Installing or Upgrading OneClick InternetNote: You must use the Honeywell supplied version of OneClick Internet. Do not change versions unless instructed by your Honeywell representative.One Click Internet is pre-installed before the Thor VM3 is shipped.If you have an installed version of OneClick Internet and need to update to a newer version, you must uninstall the previous version first by selecting Start > Control Panel and select Add or Remove Programs. Select OneClick Internet and tap Remove. Follow the on screen instructions.Note: OneClick Internet does not install the drivers for the Gobi 000 devices. Device drivers are preloaded.InstallationWhen you double-click the Installer file for OneClick Internet, it extracts the files to install.

6 - 55Next, select the application language. By default, the language of the OS is used (if available).Review and accept the license agreement. Click Accept, if you agree. Otherwise please click Reject to cancel installation.Next the installer asks for the installation directory. Use the Browse button to specify a location other than the default.

6 - 56Installation process is indicated on screen. When completed. click the Finish button to exit the installer.Start OneClick Internet from the Windows Program Menu or double-tap the desktop icon.OneClick Internet Connection ManagerLaunch OneClick Internet from the desktop icon or Windows Start Menu. When OneClick Internet is active, a status icon appears in the system tray.

6 - 57The main screen for OneClick Internet opens when the application is started. This screen displays basic information on the connection as well as access to more advanced features and details. From this screen you can connect to the Internet, send Emails, send short messages (SMS) and access the GPS.General Windows controls for minimize and exit are located at the upper right of the screen.Connection ManagementRefer to the table below for descriptions of the items in the connection management area.Icon DescriptionNetwork signal strengthAdditionally the network name is displayed to the right of the icon. The more green bars, the stronger the signal.Connect / Cancel / DisconnectTap this button to connect or disconnect. The color of this button also indicates the status of the connection: The radio is disconnected. Tap the button to connect. The radio is currently connecting. The radio is connected. Tap the button to disconnect.SMSThe SMS button is enabled if no Internet connection is active. When this button is active, tapping it ac-cesses the integrated SMS application.WebTap this button to launch the default browser.EmailTap this button to launch the default Email application.GPSTap this button access the integrated GPS tool.

6 - 58Information ButtonsIcon DescriptionRadio On/OffTap this button to switch the radio state. The color of this button also indicates the state of the radio: The radio is On. Tap the button to turn the radio Off. The radio is Off. Tap the button to turn the radio On. The radio is Connecting or the radio has been disabled. The button is inactive at this time.Statistics Show/Hide Tap the button to expand the screen to include connection statistics. See Statistics Button (page 6-42) for details. Tap the button to hide the connection statistics.SettingsTap this button to access One Clink Internet settings. Select from several tabs to configure the connection settings. See Settings Button (page 6-43) for details.UpdateTap this button to access OneClick Internet update tab. See Update Button (page 6-42).HelpClick this button to view the online help.Status Ready. Tap the Connect button to establish a connection. Connecting. Tap the Cancel button to cancel the connection in process. Connected. Tap the Disconnect button to end the connection. Failure. Review the screen for messages such as “No Network”, etc.

7 - 17Key MapsIntegrated KeypadThere are seven integrated programmable keys located on the Thor VM3 below the display. Each programmable key can be modified by the Orange key for a total of 14 programmable keys.See Programmable Key (page 5-41) to remap these keys.The default values for these keys are:The following key press sequences are not programmable:The Blue plus P3, P4 or P7 key press sequences cause no action.To get this Programmable Key Press These Keys in this Order Default Key ValueP1 (Programmable key 1) P1 F1P2 (Programmable key 2) P2 F2P3 (Programmable key 3) P3 F3P4 (Programmable key 4) P4 Open/Close Soft KeyboardP5 (Programmable key 5) P5 EnterP6 (Programmable key 6) P6 <none>P7 (Programmable key 7) P7 <none>P8 (Programmable key 8) Orange P1 <none>P9 (Programmable key 9) Orange P2 <none>P10 (Programmable key 10) Orange P3 <none>P10 (Programmable key 11) Orange P4 <none>P10 (Programmable key 12) Orange P5 <none>P10 (Programmable key 13) Orange P6 <none>P10 (Programmable key 14) Orange P7 <none>To get this function Press These Keys in this OrderIncrease speaker volume Blue P1Decrease speaker volume Blue P2Increase display brightness Blue P5Decrease display brightness Blue P6P8P1P14P7P13P6P12P5P11P4P10P3P9P2

7 - 2External 21-Key KeyboardThe table below shows the results of the keypress combinations. Each key has an unshifted mode, a Yellow shifted mode and a Green shifted mode. • To enter Yellow shifted mode, press the Yellow key. The keypad remains in Yellow shifted mode until any other key is pressed or the Yellow key is pressed again.• To enter Green shifted mode, press the Green key. The keypad remains in Green shifted mode until any other key is pressed or the Green key is pressed again.• Pressing the Yellow key then the Green key cancels Yellow mode and the keypad is in Green shifted mode.• Pressing the Green key then the Yellow key cancels Green mode and the keypad is in Yellow shifted mode.• Arrow keys are unaffected by Yellow or Green shifted mode.• Keypress combinations marked as N/A do nothing.• Pressing the backlight key (alone or after the Green or Yellow keys) cycles the keypad backlight through Low, Medium, High, Off then repeats.To get this Key Press These Keys in this Order0 - 9 0 - 91 F1 - F10 Yellow 1 - 0F11 - F20 Green 1 - 0P15 PF P16 Yellow PFDelete DelBackspace Yellow DelTab TabBacktab Yellow TabOrange P3Orange P4Orange P5Orange P6

$7 - 3External 95-Key KeyboardThese key functions apply to both the 95-Key USB Keyboard (page 3-18) and the 95-key PS/2 Keyboard (page 3-19).The key map table that follows lists the commands used for the Thor VM3. Note that since the Thor VM3 uses a Microsoft Win-dows operating system, no DOS Terminal Emulation keypress sequences are provided.There are 10 hidden keys on the 95 key keyboard. Each of the hidden keys is accessed by pressing the <Fn> key (located in the top right hand corner) plus a key on the numeric keypad on the right. Additional function keys are supported as well.To get this Key / Function Press These Keys in this OrderInsert FN 0 (numeric keypad)Home FN 7 (numeric keypad)Page Up FN 9 (numeric keypad)Delete FN . (numeric keypad)End FN 1 (numeric keypad)Page Down FN 3 (numeric keypad)Up Arrow FN 8 (numeric keypad)Left Arrow FN 4 (numeric keypad)Down Arrow FN 2 (numeric keypad)Right Arrow FN 6 (numeric keypad)PrintScreenSysRqScrollLockPauseBreak67BackSpaceNumLockERTYUI OP]\[{}|7410HomeDF GHJ K L;':"EnterAltCV BNM,<.>/?ShiftAlt CtrlInsEnd4$5%^&9(0)-_=+LRXEsc F3 F4 F5 F6 F7 F8 F9 F10 F11 F12F1 F2 Fn123/*-TabQW895623PgUpCapsLockASShiftCtrlPgDn+`~!@#Enter.Del8*Z$

$7 - 4External 60-Key KeyboardThe key map table that follows lists the commands used when using the Thor VM3 with the 60-key PS/2 Keyboard (page 3-20).The 60-key keyboard does not have a NumLock indicator or key. NumLock can be toggled On or Off using the 2nd SHIFT F10 keypress sequence. The default for NumLock is On. Changes made to the NumLock status persist across a Windows restart.When running RFTerm, please refer to the RFTerm Reference Guide for equivalent keys and keypress sequences.60 Key KeyMap 101-Key Equivalencies• The following keymap is used on an Thor VM3 that is NOT running RFTerm. When running RFTerm an optional IBM 3270 Keypad Overlay (page 7-9) or IBM 5250 Keypad Overlay (page 7-9) is available.• When using a sequence of keys that includes the 2nd key, press the 2nd key first then the rest of the key sequence.• When the Thor VM3 boots, the default condition of Caps (or CapsLock) is Off. The Caps (or CapsLock) condition can be toggled with a 2nd + F1 key sequence. The CAPS LED is illuminated when CapsLock is On. The keymaps below assume Caps is Off.• The Thor VM3 keyboard has several control keys. The following control keys are not used:» The 2nd function of the F3 key is not used as Windows Power Management controls all power management modes on the Thor VM3.» The 2nd functions of the F4 and F5 keys are not used as the display brightness is adjusted via the buttons on the front of the Thor VM3.» The 2nd functions of the F6 and F7 keys are not used as the Thor VM3 has TFT LCD screen with no provision for contrast adjustments.» The 2nd functions of the F8 and F9 keys are not used as the sound volume on the Thor VM3 is controlled with a Microsoft Windows Control Panel.» The 2nd function of the F10 key is not used as the display backlight timer also controls the keyboard backlight.To get this Key / Function Press These Keys in this OrderPower On/Off Power 2nd 2nd Shift Shift Alt Alt Ctrl Ctrl Esc Esc Space Sp Enter Enter Enter (numeric) 2nd Enter CapsLock (Toggle) 2nd F1 Back Space BkSp Tab Tab Back Tab 2nd Tab Ctrl-Break Ctrl 2nd F2Pause 2nd F2 CAPS2nd987/-+456INSBKSPCTRL#E*I!Q@WO(P)R$T%U&Y^ =}{PgUpENTERSHIFT:D;F"G'H.K123L?S\A|J’]>[HomePgDn ENDALT SP ~BCVXZDEL0M_N´<.CAPSBREAKR/S BKLTESC 2NDF1 F2 F3 F4 F5 F6 F7 F8 F9 F10$

7 - 5Up Arrow Up Arrow Down Arrow Down Arrow Right Arrow Right Arrow Left Arrow Left Arrow Insert 2nd Bksp Delete (numeric) 2nd DOT Home 2nd Left Arrow End 2nd Right Arrow Page Up 2nd Up Arrow Page Down 2nd Down Arrow ScrollLock 2nd Shift F10F1 F1 F2 F2 F3 F3 F4 F4 F5 F5 F6 F6 F7 F7 F8 F8 F9 F9 F10 F10 F11 2nd Shift F1F12 2nd Shift F2aA bB cC dD eE fF gG hH iI jJ kK lL mM nN oO pP qQ rR sS

7 - 6tT uU vV wW xX yY zZ AShiftA BShiftB CShiftC DShiftD EShiftE FShiftF GShiftG HShiftH IShiftI JShiftJ KShiftK LShiftL MShiftM NShiftN OShiftO PShiftP QShiftQ RShiftR SShiftS TShiftT UShiftU VShiftV WShiftW XShiftX YShiftY ZShiftZ 11 22 33 44 55 66 77 88 99

$7 - 700 DOT DOT <2nd0 [2nd1 ]2nd2 >2nd3 =2nd4 {2nd5 }2nd6 / (numeric) 2nd Ctrl 7/ (alpha) 2nd 7 - (numeric) 2nd Ctrl 8- (alpha) 2nd 8 + (numeric) 2nd Ctrl 9+ (alpha) 2nd 9 * (numeric) 2nd I (letter i) * (alpha) 2nd Ctrl I (letter i): (colon) 2nd D ; (semicolon) 2nd F ?2ndL `2ndN _ (underscore) 2nd M , (comma) 2nd J ' (apostrophe) 2nd H ~ (tilde) 2nd B \2ndS |2ndA "2ndG !2ndQ @2ndW #2ndE $2ndR %2ndT ^2ndY &2ndU (2ndO )2ndP$

Honeywell VM3WWANA Vehicle Mount Computer User Manual VM3 W7 UG

Honeywell International Inc Vehicle Mount Computer VM3 W7 UG

Contents

User manual_2

Navigation menu

Namespaces

Views

Navigation