Hoover Vacuum Cleaner Purepower PU2120 Instruction Manual Product Code 39100201
User Manual: Hoover Instruction Manual Purepower PU2120 - Vacuum Cleaner Help and Advice from Hoover
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
Pure Power-ok 2004.4.16 10:55 AM Page 2 I M P O RTA N T S A F E T Y R E M I N D E R S User’s manual-This cleaner should only be used for its intended purpose as described in these instructions. Ensure that these are fully understood before operating this appliance. Only use attachments recommended or supplied by Hoover. When using cleaning tools ensure that the cleaner is kept in the upright (parked) position.This will avoid possible damage to the carpet or floor covering.When cleaning stairs DO NOT position the cleaner above you. STATIC ELECTRICITY. Some carpets can cause a small build up of static electricity. Any static discharge is not hazardous to health. DO NOT use your cleaner out of doors or on any wet surface or for wet pick up. Air freshener pads must be kept away from children. DO NOT suck, swallow or chew air freshener pads. Keep hands, feet, loose clothing and hair away from rotating brushes. DO NOT pick up hard or sharp objects, matches, hot ashes, cigarette ends or other similar items. HOOVER SERVICE HOOVER SPARES Congratulations on the purchase of your new Hoover PurePower. DO NOT pick up flammable liquids such as cleaning fluids, petrol etc. or their vapours. This highly advanced machine - with new technology unique to Hoover - makes cleaning easier and more efficient. Aerosol sprays may be flammable. DO NOT spray near cleaner. SUPPLY CORD. DO NOT run over the supply cord when using your cleaner or remove the plug by pulling on the supply cord. You’ll find it kinder to your carpets - and to you! Please take the time to read this manual carefully. FAULTS. DO NOT continue to use your cleaner if it appears to be faulty. If the supply cord is damaged stop using the cleaner IMMEDIATELY. The supply cord must be replaced by an authorised Hoover service engineer to avoid a safety hazard. You’ll be ready to make the most of the special features only the new Hoover PurePower can offer! AFTER USE. Switch the cleaner off and remove the plug from the electricity supply. Always switch off and remove the plug before cleaning the appliance or attempting any maintenance task. WARNING! ELECTRICITY CAN BE EXTREMELY DANGEROUS HOOVER SERVICE. To ensure the continued safe and efficient operation of this appliance we recommend that any servicing or repairs are only carried out by an authorised Hoover service engineer. This appliance is double insulated and must not be earthed. The plug is fitted with a 13 amp fuse. IMPORTANT:The wires in the mains lead are coloured in accordance with the following code: 08705 400 600 01204 556 111 Blue - NEUTRAL Brown - LIVE Use only HOOVER paper bags and filters PurePower -2- Pure Power-ok 2004.4.16 10:55 AM Page 4 C A R P E T H E I G H T S E L E C TO R P R E PA R I N G TO U S E YO U R C L E A N E R 1 Insert handle into body of cleaner. Slide into position. Ensure handle is flush with body of cleaner. Tighten large screw (pre-fitted to handle upper hole). Insert small screw into handle lower hole and tighten. 2 Locate hose end, turn clockwise to lock. 3 Locate hose retainer on lower hose support. 4 Position hose over hose supports 5 Push handgrip firmly into socket. Clip tools to back of cleaner. The carpet height selector raises or lowers the height of the nozzle.The nozzle height will not change until the handle is released.Try various settings until you get the best results for each of your carpets. 2 3 ! Ensure that cleaner is in the upright (parked position). 4 1 IMPORTANT: When cleaning hard floors such as vinyl or linoleum, move the “Height Right” selector knob to the hard floor position. Failure to do so may cause damage to the floor surface. Check that paper bag is fitted, if not fit new one (See ‘Changing the paper bag’ overleaf). Slide knob to position best suited to depth of carpet pile. Using this cleaner for carpets with pile greater than 30mm is not recommended. P OW E R S W I T C H S E T T I N G S 5 Switching on and off Push bottom of switch to switch on. Push top of switch to switch off. HANDLE LOCK RELEASE Unlock the handle by pressing down on pedal with foot. For cleaning under low furniture and some maintenance tasks simply press pedal again and lower handle to floor. -4- Dust_Manager_6.eps 17:16:31 Page_06.ai 22/3/05 19/10/05 3:36:04 pm C H A N G I N G B E LT O R B RU S H E S C L E A R I N G A B L O C K AG E 3 2 1 IMPORTANT: Switch cleaner off and remove plug from electricity supply before checking the brushes or removing hood. Refit brush assembly • Hold the brush assembly and stretch the belt until brush mountings slot down into the cleaner housing Rotate the brush to ensure free movement of the belt. If your cleaner is not picking up efficiently, the belt or brushes (or both) may need replacing, but first make sure you have: • Emptied the dust container • Cleaned filters • Checked for blockages b 4 Refit hood • Refit hood, ensuring the lugs along the front of hood are located in the slots along the front edge of baseplate. • Secure hood, using screws A and B. C M Y CM MY CY CMY 1 a Remove hood • Prise off carpet-care control knob • Remove hood screws A and B Lift off hood 5 Refit carpet-care control knob • Ensure the raised face (T) is towards the front of the cleaner. K ! IMPORTANT: Switch the cleaner off and remove the plug from the electricity supply before dismantling cleaner. This cleaner is unlikely to become blocked, except by overfilling of the dust container or accidentally picking up large solid objects. Clearing a blockage is simple. If cleaning tools were in use, check cleaning tool and extension tube first. Next check hose handgrip; to remove grip ribbed ring as shown, turn in direction of arrow and ease apart. To check the hose, stretch it to full length and switch on the cleaner; the suction will dislodge most obstructions. If this is unsuccessful, switch off and unplug the cleaner. Remove the hose by turning it anti-clockwise as shown. Detach cassette and remove blockage. For blockages in cleaner base: 1.Turn the cleaner over and check that the brushes are free to rotate. 2 Remove brush assembly • Inspect belt for signs of wear. • To remove, pull brush cleaner assembly upwards out of cleaner housing. Remove belt from motor spindle then from brush assembly. Removing a blockage from the ‘Pet hair remover’ (Certain models only) Open clip and lift cover to remove blockage. Replace belt • Loop the new belt around the motor spindle then around the brush channel. -6- 2. Check for a blockage in hose socket. Use a piece of wire or a blunt flexible rod to remove any obstructions. Pure Power-ok 2004.4.16 10:55 AM Page 8 Bag check indicator (certain models only) User checklist For an accurate reading of the bag check indicator ensure that: ● flexible hose handgrip is pushed firmly into its socket. If your cleaner is not working properly run through the following checklist. ● On Variable Power models control is set to maximum. The continuous red light of the bag check indicator will come on if: 1. Is there a working electricity supply to the cleaner? Check with another electrical product. ● Bag needs replacement. If picking up fine powders more frequent replacement will be required even although the bag does not appear well filled. ● Filters are dirty. ● There is a blockage. The light may flicker on and off during normal use. 2. Is the bag full or choked with fine dust? 3. Is the hose blocked? 4. Is there a blockage in the cleaner base? 5. Are the filters blocked? WARNING! A thermal cut out switches off the cleaner to prevent overheating if it is used when full or there is a blockage or dirty filters. If this should happen switch off, unplug and correct the fault. 6. Is the nozzle height set correctly? 7. Are the brushes rotating correctly? 8. Has the cleaner overheated? If so, it will take about 30 minutes to reset. It will take about 30 minutes for the cut out to automatically reset. If there is any doubt call your local Hoover Service Office for advice. They may be able to assist you over the telephone. IMPORTANT: Do not run cleaner over the supply cord as this could damage the supply cord insulation. * Hoover Limited Pentrebach Merthyr Tydfil Mid-Glamorgan C F48 4T U ISO9001 C opyright 2001 BEAB Approved * Registered Trade Mark -8- Part no: 05655202
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 8 Has XFA : No Create Date : 2004:04:16 03:09:14Z Modify Date : 2018:04:16 02:04:19+01:00 Producer : Acrobat Distiller 5.002001-01-22:00 for Macintosh; modified using iTextSharp™ 5.5.12 ©2000-2017 iText Group NV (AGPL-version) Author : Hoover Candy Group Creator : QuarkXPress. 4.01: PSPrinter 8.3 Title : Hoover Vacuum Cleaner Purepower PU2120 Instruction Manual - Product Code 39100201 Subject : Download the PDF user manual for your Vacuum Cleaner Purepower PU2120 directly from the manufacturer, HooverEXIF Metadata provided by EXIF.tools