Horizon Hobby PLANO1T Plano RF Module User Manual Plano User Guide f

Download:
Mirror Download [FCC.gov]
Document ID	3993732
Application ID	XgrfXidOfC+SAENgzwqEaQ==
Document Description	Exhibit D Users Manual per 2 1033 b3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	12.73kB (159119 bits)
Date Submitted	2018-09-06 00:00:00
Date Available	2018-09-06 00:00:00
Creation Date	2018-08-20 08:51:18
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2018-08-20 08:51:18
Document Title	Microsoft Word - Plano User Guide (f)
Document Creator	PScript5.dll Version 5.2.2
Document Author:	decrowder

Plano RF Module User Manual
Horizon Hobby, LLC
4105 Fieldstone Rd
Champaign, IL 61822
1. Features
 2.4GHz Frequency Hopping spread spectrum (FHSS) radio transceiver module
 Operates in the unlicensed worldwide ISM band (2.4 GHz to 2.483.5GHz) band
 Fully integrated power regulation with a wide input unregulated operating range 3V to
10V
 Fully integrated local oscillator and 24MHz 10ppm reference crystal
 400mA operating current
 Transmit power - <=18.5dBm in EU, <=26dBm in North America
 Receive sensitivity up to -95dBm
 DSSS data rates up to 1Mbps
 1 mile operating range
 Full packet assembling and disassembling
 Auto transaction sequencer
 Fully buffered digital interface with high voltage tolerant inputs
2. Pin description
Pin Number
Name
RF_P
RF_N
3,7,17,20,29,3 GND
RX_TX
X32K_Q1
X32K_Q2
DIO_0
DIO_1
10
DIO_2
11
12
VDDS2
DCOUPL
13
JTAG_TMSC
Description
Positive RF input signal to LNA during RX
Positive RF output signal to PA during TX
Negative RF input signal to LNA during
RX
Negative RF output signal to PA during TX
Module GND
Optional bias pin for the RF LNA
32-kHz crystal oscillator pin 1
32-kHz crystal oscillator pin 2
GPIO, Sensor Controller, high-drive
capability
GPIO, Sensor Controller, high-drive
capability
GPIO, Sensor Controller, high-drive
capability
1.8-V to 3.8-V GPIO supply
1.27-V regulated digital-supply decoupling
capacitor(
JTAG TMSC
Page 1 of 4
14
15
16
18
JTAG_TCKC
DIO_3
DIO_4
DCDC_SW
19
21
22
23
24
25
26
27
28
VDDS_DCDC
RESET_N
DIO_5
DIO_6
DIO_7
DIO_8
DIO_9
VDDS
VDDR
30
31
32
X24M-N
X24M_P
VDDR_RF
JTAG TCKC
GPIO, High drive capability, JTAG_TDO
GPIO, High drive capability, JTAG_TDI
Output from internal DC-DC. Tie to ground
for external regulator mode
(1.7-V to 1.95-V operation)
Reset, active-low. No internal pullup.
GPIO, Sensor Controller, Analog
GPIO, Sensor Controller, Analog
GPIO, Sensor Controller, Analog
GPIO, Sensor Controller, Analog
GPIO, Sensor Controller, Analog
1.8-V to 3.8-V main chip supply
1.7-V to 1.95-V supply, typically connect to
output of internal DC-DC.
24-MHz crystal oscillator pin 1
24-MHz crystal oscillator pin 2
1.7-V to 1.95-V supply, typically connect to
output of internal DC-DC(
3. Specifications
Parameter
Storage Temp
VDD
Receive Sensitivity
Transmit power (conducted)
Transmit power (radiated)
Idle current
Receive current
Transmit current
Value
-65 to 105
2.4 to 3.6
-95
25.5
27
22
400
Units
Degrees Celsius
Volts
dBm
dBm MAX
dBm MAX
mA
mA
mA
Page 2 of 4
4. Module User Requirements
4.1 This module must be integrated into a device where the user cannot access the antenna
connector.
4.2 Only a 1.5dBi antenna can be used with this module. The antenna must meet and not exceed
the gain and pattern of the supplied folded dipole antenna.
4.3 The device must contain the following permanent labeling on the exterior of the device as
follows:
Contains FCC ID: BRWPLANO1T
Contains IC: 6157A-PLANO1T
4.4 The user manual of the device must contain the following paragraph:
Page 3 of 4
FCC Information
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Caution:
Changes or modifications not expressly approved by the party
manufacturer could void the user’s authority to operate the equipment.
4.5 This module meets the requirements for a mobile device that may be used at
separation distances of more than 5cm from the human body. It may be used in hand-held
controllers that provide a separation distance of at least 5cm between the antenna and the
body (excluding hands/wrists).
IC Information
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
CE Information
This product contains a radio transmitter with wireless technology
which has been tested and found to be compliant with the applicable
regulations governing a radio transmitter in the 2.400 GHz to 2.4835 GHz
frequency range.
Page 4 of 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : decrowder
Create Date                     : 2018:08:20 08:51:18-05:00
Modify Date                     : 2018:08:20 08:51:18-05:00
XMP Toolkit                     : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 11.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - Plano User Guide (f)
Creator                         : decrowder
Document ID                     : uuid:e0c25d0a-8fda-48f8-a761-ed70779d916e
Instance ID                     : uuid:0fce1b66-24f8-445e-acaa-072c6b38ff63
Page Count                      : 4

EXIF Metadata provided by EXIF.tools