Horizon Hobby SR2100AL SR2100 Receiver User Manual BRWSR2100AL English

Horizon Hobby, LLC SR2100 Receiver BRWSR2100AL English

Contents

BRWSR2100AL_English User Manual

Download: Horizon Hobby SR2100AL SR2100 Receiver User Manual BRWSR2100AL English
Mirror Download [FCC.gov]Horizon Hobby SR2100AL SR2100 Receiver User Manual BRWSR2100AL English
Document ID3807422
Application IDJlUDKqIiy43BYNUg7JQH0Q==
Document DescriptionBRWSR2100AL_English User Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize14.96kB (186962 bits)
Date Submitted2018-04-05 00:00:00
Date Available2018-04-08 00:00:00
Creation Date2018-03-23 12:57:24
Producing SoftwareAcrobat Distiller 10.1.12 (Macintosh)
Document Lastmod2018-03-23 13:05:27
Document Title52929.3_SPM_SPMSR2100_DSMR Micro Race Rx Antenna-Less_MULTI.indb
Document CreatorAdobe InDesign CS5.5 (7.5.3)
Document Author: ashell

SR2100 Instruction Manual
SR2100 Bedienungsanleitung
Manuel d’utilisation SR2100
Manuale di istruzioni SR2100
EN
NOTICE
All instructions, warranties and other collateral documents are subject to
change at the sole discretion of Horizon Hobby, LLC. For up-to-date product
literature, visit horizonhobby.com and click on the support tab for this
product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate
various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability
of property damage, collateral damage, and serious injury OR create a high
probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the probability
of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of
physical property damage AND a little or no possibility of injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
WARNING: Read the ENTIRE instruction manual to become familiar
with the features of the product before operating. Failure to operate the
product correctly can result in damage to the product, personal property and
cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and
common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or
damage to the product or other property. This product is not intended for use
by children without direct adult supervision. Do not attempt disassembly, use
with Incompatible components or augment product in any way without the
approval of Horizon Hobby, LLC. This manual contains instructions for safety,
operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to
operate correctly and avoid damage or serious injury.
WARNING AGAINST COUNTERFEIT PRODUCTS
Always purchase from a Horizon Hobby, LLC authorized dealer to ensure
authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims
all support and warranty with regards, but not limited to, compatibility and
performance of counterfeit products or products claiming compatibility with
DSM or Spektrum technology.
NOTICE: This product is only intended for use with unmanned, hobby-grade,
remote-controlled vehicles and aircraft. Horizon Hobby disclaims all liability
outside of the intended purpose and will not provide warranty service related
thereto.
WARRANTY REGISTRATION
Visit www.community.spektrumrc.com today to register your product.
EN
SR2100 Instruction Manual
The Spektrum™ SR2100 3-channel DSMR® Micro Race, Antenna-Less receiver
is compatible with all Spektrum DSMR surface transmitters.
Specifications
SR2100
Type
Dimensions
(LxWxH)
Channels
Weight
Band
Frame rate
Voltage Range
DSMR Micro Race
17.6 x 25.5 x 25mm
5.5g
2404-2476 MHz
11ms-5.5ms
3.5–9V
Steering Port
Aux 1 Port
Throttle Port
Bind Button
Table of Contents
Receiver Installation and Setup ...................................................... 4
Binding Receiver to Transmitter ...................................................... 5
Aux channels ................................................................................ 5
Troubleshooting Guide ................................................................... 6
1-Year Limited Warranty ................................................................ 7
Warranty and Service Contact Information ...................................... 9
FCC Information ............................................................................ 9
EU Compliance Statement: ..........................................................10
EN
Receiver Installation and Setup
The Spektrum SR2100’s micro size and lack of antenna, allows for easy
installations. Simply install the receiver in your vehicle using double-sided foam
servo tape.
Powering the receiver with a separate receiver pack
Battery
Throttle Servo
Receiver
Steering Servo
Powering the receiver with an ESC
Battery
To Motor
Electronic
Speed Control
Receiver
Steering Servo
Failsafe
The throttle failsafe position is set during binding. In the unlikely event that
transmitter signal is lost during use, the receiver will drive the the throttle servo
to its pre-programmed failsafe position. If you power on the receiver before
powering on the transmitter, the receiver enters failsafe mode. Normal control
resumes when you power on the transmitter.
CAUTION: Failsafe activates only in the event that signal is lost from
the transmitter. Failsafe does NOT activate in the event that the receiver
loses battery power.
EN
Binding Receiver to Transmitter
In order to operate, the receiver must be bound to the transmitter. Binding
is the process of programming the receiver to recognize the GUID (Globally
Unique Identifier) code of a single specific transmitter. When a receiver is
bound to a transmitter/model memory, the receiver will only respond to that
specific transmitter/model memory.
Binding
1. Push and hold the bind button on the receiver while powering up the
receiver. The orange LED will flash continuously, indicating that the receiver
is in bind mode.
2. With all channels in the desired preset failsafe position (normally neutral),
put your transmitter in bind mode. Continue holding the failsafe position until
the binding process is complete.
3. The bind process is complete when the orange LED on the receiver is solid.
CAUTION: When the bind process is complete, the throttle and
steering channels are active. Keep hands and loose objects away
from all rotating parts.
You must rebind the transmitter and receiver if you:
• Change the servo reverse after binding
• Want to use the receiver with a different model memory
• Are using the receiver with a DSMR transmitter and you change the frame
rate in the transmitter
Aux channel
The Aux channel can operate as extra servo channel, or as a power supply for
a personal transponder.
•
If 5.5ms frame rate is selected in the transmitter, only two channels,
Steering and Throttle, are operational. The Aux channel can be used to
power a personal transponder, a fan or lights.
•
If a frame rate other than 5.5ms is selected, the Aux channel will operate
as extra servo channel.
•
A Y-harness (SPM1516) may be used to operate two auxilary items from
one servo port.
IMPORTANT: You must re-bind any time you change the frame rate in the
transmitter.
IMPORTANT: The DX4R Pro DX5R, Dx5 Pro or DX6R are required for 5.5ms frame
rate.
EN
Troubleshooting Guide
Problem
Possible Cause
Solution
The system will
not connect
You are near metal objects
Move to an area with less
metal
The receiver is bound to a
different model memory
Make sure the correct
model memory is active in
your transmitter
Your transmitter was
placed into bind mode and
is no longer bound to your
receiver
Rebind your transmitter
and receiver
The receiver
goes into
failsafe mode a
short distance
away from the
transmitter
The antenna inside the
receiver case could
become damaged if the
receiver is damaged
Inspect the receiver for
damage
The receiver
stops responding during
operation
Low receiver battery voltage. If the battery voltage
is low, it may drop below
3.5V momentarily, causing
the receiver to brown-out,
then reconnect
Charge the receiver or
vehicle battery. Spektrum
receivers require at least
3.5V to operate
Loose or damaged wires
or connectors between
battery and receiver
Check the wires and
connection between the
battery and receiver. Repair
or replace wires and/or
connectors
Replace the receiver or
contact Horizon Product
Support
EN
1-Year Limited Warranty
What this Warranty Covers - Horizon Hobby, LLC, (Horizon) warrants to the
original purchaser that the product purchased (the “Product”) will be free from
defects in materials and workmanship for a period of 1 year from the date of
purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii)
damage due to acts of God, accident, misuse, abuse, negligence, commercial
use, or due to improper use, installation, operation or maintenance, (iii)
modification of or to any part of the Product, (iv) attempted service by anyone
other than a Horizon Hobby authorized service center, (v) Product not purchased
from an authorized Horizon dealer, (vi) Product not compliant with applicable
technical regulations, or (vii) use that violates any applicable laws, rules, or
regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER
WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL
IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY
ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE
REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that
Horizon will, at its option, either (i) service, or (ii) replace, any Product determined
by Horizon to be defective. Horizon reserves the right to inspect any and all
Product(s) involved in a warranty claim. Service or replacement decisions are
at the sole discretion of Horizon. Proof of purchase is required for all warranty
claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS
THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR
COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR
ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of
Horizon exceed the individual price of the Product on which liability is asserted.
As Horizon has no control over use, setup, final assembly, modification or misuse,
no liability shall be assumed nor accepted for any resulting damage or injury. By
the act of use, setup or assembly, the user accepts all resulting liability. If you
as the purchaser or user are not prepared to accept the liability associated with
the use of the Product, purchaser is advised to return the Product immediately in
new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law
principals). This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state. Horizon reserves the right to change
or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support
or service. Once assembly, setup or use of the Product has been started, you
must contact your local distributor or Horizon directly. This will enable Horizon
EN
to better answer your questions and service you in the event that you may
need any assistance. For questions or assistance, please visit our website at
www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free
telephone number referenced in the Warranty and Service Contact Information
section to speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country
you live and use the Product in, please use the Horizon Online Service Request
submission process found on our website or call Horizon to obtain a Return
Merchandise Authorization (RMA) number. Pack the Product securely using a
shipping carton. Please note that original boxes may be included, but are not
designed to withstand the rigors of shipping without additional protection. Ship
via a carrier that provides tracking and insurance for lost or damaged parcels,
as Horizon is not responsible for merchandise until it arrives and is accepted at
our facility. An Online Service Request is available at http://www.horizonhobby.
com/content/service-center_render-service-center. If you do not have internet
access, please contact Horizon Product Support to obtain a RMA number along
with instructions for submitting your product for service. When calling Horizon,
you will be asked to provide your complete name, street address, email address
and phone number where you can be reached during business hours. When
sending product into Horizon, please include your RMA number, a list of the
included items, and a brief summary of the problem. A copy of your original
sales receipt must be included for warranty consideration. Be sure your name,
address, and RMA number are clearly written on the outside of the shipping
carton.
NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue
with a LiPo battery, please contact the appropriate Horizon Product
Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt verifying
the proof-of-purchase date. Provided warranty conditions have been met, your
Product will be serviced or replaced free of charge. Service or replacement
decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed and
payment will be required without notification or estimate of the expense unless
the expense exceeds 50% of the retail purchase cost. By submitting the item
for service you are agreeing to payment of the service without notification.
Service estimates are available upon request. You must include this request
with your item submitted for service. Non-warranty service estimates will be
billed a minimum of ½ hour of labor. In addition you will be billed for return
freight. Horizon accepts money orders and cashier’s checks, as well as Visa,
MasterCard, American Express, and Discover cards. By submitting any item to
Horizon for service, you are agreeing to Horizon’s Terms and Conditions found
on our website http://www.horizonhobby.com/content/service-center_renderservice-center.
ATTENTION: Horizon service is limited to Product compliant in the
country of use and ownership. If received, a non-compliant Product
will not be serviced. Further, the sender will be responsible for
arranging return shipment of the un-serviced Product, through a
carrier of the sender’s choice and at the sender’s expense. Horizon
will hold non-compliant Product for a period of 60 days from
notification, after which it will be discarded.
5-14-2015
EN
Warranty and Service Contact Information
Country of
Purchase
United States of
America
EU
Horizon Hobby
Contact Information
Horizon Service
Center
(Repairs and Repair
Requests)
servicecenter.horizonhobby.
com/RequestForm/
Horizon Product
Support
(Product Technical
Assistance)
productsupport@horizonhobby.
com.
Address
4105 Fieldstone Rd
Champaign, Illinois,
61822 USA
877-504-0233
websales@horizonhobby.com
Sales
800-338-4639
Horizon Technischer service@horizonhobby.de
Service
Sales: Horizon Hobby +49 (0) 4121 2655 100
GmbH
Hanskampring 9
D 22885 Barsbüttel,
Germany
FCC Information
FCC ID: BRWSR2100AL
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTICE: Modifications to this product will void the user’s authority to
operate this equipment.
This product contains a radio transmitter with wireless technology which has been
tested and found to be compliant with the applicable regulations governing a radio
transmitter in the 2.400GHz to 2.4835GHz frequency range.
Antenna Separation Distance
When operating your Horizon Hobby product, please be sure to maintain a
separation distance of at least 20 cm between your body (excluding fingers,
hands, wrists, ankles and feet) and the antenna to meet RF exposure safety
requirements as determined by FCC regulations.
EN
IC Information
IC: 6157A-SR2100AL
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
EU Compliance Statement:
EU Compliance Statement:
Horizon Hobby, LLC hereby declares that this product is in compliance
with the essential requirements and other relevant provisions of the RED
Directive.
A copy of the EU Declaration of Conformity is available online at:
http://www.horizonhobby.com/content/support-render-compliance.
Instructions for Disposal of WEEE by Users in the European Union
This product must not be disposed of with other waste. Instead, it is the
user’s responsibility to dispose of their waste equipment by handing it
over to a designated collection point for the recycling of waste electrical
and electronic equipment. The separate collection and recycling of your
waste equipment at the time of disposal will help to conserve natural resources
and ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office, your household
waste disposal service or where you purchased the product.
10
© 2018 Horizon Hobby, LLC.
DSM, DSMR and the Horizon Hobby logo are trademarks or registered trademarks of
Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
All other trademarks, service marks and logos are property of their respective owners.
Patents pending.
04/18
52929.3

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : ashell
Create Date                     : 2018:03:23 12:57:24-05:00
Modify Date                     : 2018:03:23 13:05:27-05:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : Adobe InDesign CS5.5 (7.5.3)
Metadata Date                   : 2018:03:23 13:05:27-05:00
Producer                        : Acrobat Distiller 10.1.12 (Macintosh)
Format                          : application/pdf
Creator                         : ashell
Title                           : 52929.3_SPM_SPMSR2100_DSMR Micro Race Rx Antenna-Less_MULTI.indb
Document ID                     : uuid:d8984b52-51d7-3f4d-8022-5ab971d695fc
Instance ID                     : uuid:dcede91d-f499-e246-9a3a-34a1dd01ef2b
Page Count                      : 11
EXIF Metadata provided by EXIF.tools
FCC ID Filing: BRWSR2100AL

Navigation menu