Huawei Technologies MU736 HSPA + Module User Manual Manual system

Download:
Mirror Download [FCC.gov]
Document ID	2341566
Application ID	PepaGzU1OD+VMxr/S+MNNg==
Document Description	User Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	124.34kB (1554204 bits)
Date Submitted	2014-07-31 00:00:00
Date Available	2014-07-31 00:00:00
Creation Date	2014-07-21 17:40:45
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2014-07-29 10:56:17
Document Title	Manual (system).pdf
Document Creator	Microsoft® Office Word 2007
Document Author:	apple

User Guide
For Windows 8.1 Tablet-laptop TL10IE2
Regulatory Compliance
Information
FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
z Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
z Consult the dealer or an experienced radio/TV technician
for help.
This device meets the government’s requirements for exposure
to radio waves.
This device is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy set
by the Federal Communications Commission of the U.S.
Government, Industry Canada, and other national regulatory
agencies.
The exposure standard employs a unit of measurement known
as the Specific Absorption Rate, or SAR. Tests for SAR are
conducted using standard operating positions accepted by the
FCC with the device transmitting at its highest certified power
level in all tested frequency bands. Although the SAR is
determined at the highest certified power level, the actual SAR
level of the device while operating can be well below the
maximum value. This is because the device is designed to
operate at multiple power levels so as to use only the power
required to reach the network. In general, the closer you are to a
wireless base station antenna, the lower the power output.
Equipment Authorization has been granted to this model with all
reported SAR levels evaluated as in compliance with the FCC
RF exposure guidelines. SAR information on this device is on
file with the FCC and can be found under the Display Grant
section of www.fcc.gov/oet/ea/fccid after searching the FCC ID:
WL6-TMBCC0002
For questions related to the EMC performance of this product,
FCC Caution: Any changes or modifications not expressly approved by the
contact:
party responsible for compliance could void the user's authority to operate
Elitegroup Computer Systems Co., Ltd
this equipment.
No.239, Sec. 2, Ti Ding Blvd., Taipei, Taiwan 11493
886-2162-1177
Canadian Department of Communications Compliance
Statement
This digital apparatus does not exceed the Class B limits for
radio noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of
Communications. This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of
the device.
Le présent appareil numerique német pas de bruits radio
électriques dépassant les limites applicables aux appareils
numériques de la classe B prescrites dans le Réglement sur le
broullage radioélectrique édicté par le ministére des
Communications du Canada. Le présent appareil est conforme
aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de
brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
CE mark. Declaring compliance to all the applicable
European Union (EU) directives. For CE mark related
questions:
Elitegroup Computer Systems Co., Ltd
No.239, Sec. 2, Ti Ding Blvd., Taipei, Taiwan 11493
886-2162-1177
French SAR/DAS
Votre ordinateur tablette a un DAS. Pour plus d'informations,
voir le portail radiofréquences-sante-environnement:
www.radiofrequences.gouv.fr
In the European Union, this symbol indicates that
this product including battery must not be disposed
of with household waste. It is your responsibility to
hand it over to a designated collection point for the
recycling of waste electrical and electronic
equipment. For more information, please contact
your local waste collection center or the point of
purchase of this product.
Japan VCCI Statement
Taiwan battery recycling:
Translation – please recycle batteries
Attention: Teachers, Parents
and Adult Supervisors
This product is an educational tool designed for school children,
ages 6 and up. There must be supervision by an adult on
school children under 10 when using this Intel Classmate PC Convertible.
It is a must to have a thorough explanation to
students on safe and proper handling of the Intel Classmate PC
- Convertible, power supply, battery pack, and power cord.
Be sure to keep the power cord away from
younger children
Please ensure that students understand the following:
 As with all electrical products, precautions should be observed
during handling and use to prevent electric shock. The power
supply (adapter) should not be handled by the children.”
 Emphasize to students that this device is an educational tool and
not a toy. The computer, power supply, battery pack or power
cord should not be dropped, crushed, stepped on or otherwise
abused.
 Ensure students understand the safe and proper handling of
power cord and power supply. Misuse could result in serious
injury.
 The teacher, parent or adult supervisor should periodically
inspect the computer; power supply and power cord for damage
and replace it, if necessary.
 Students should report any damage or loose parts to their
teacher, parent or adult supervisor, immediately.
 Do not leave the PC plugged in or “on” when enclosed in a
non-vented container, such as a school backpack, as overheating
may occur.
 It is recommended that students should take a 5 minute break
every 30 minutes of use.
Safety Precautions
The following are lists of precautionary measure the students
must understand before using this computer inside the
classroom or home environment:
1.
2.
3.
4.
5.
6.
Do not place near the fire or other sources of heat.
Do not expose to magnetic fields.
Do not expose to direct sunlight.
Do not expose to rain or moisture.
Do not place heavy objects to add heavy pressure on
the computer.
Do not drop the computer.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS.
Contents
1. Getting to know your computer ........................................ 1
Package contents ................................................................................. 1
Separating your tablet-laptop ................................................................ 1
Layout ................................................................................................... 2
Tablet Views ................................................................................. 2
Front .................................................................................... 2
Back ..................................................................................... 3
Left (I/O cabinet) .................................................................. 4
Bottom ................................................................................. 4
Keyboard Duck Views .................................................................. 5
Connectors and indicators ................................................... 5
Shortcut keys ....................................................................... 6
2.
Using your computer ...................................................... 7
Powering ON/OFF ................................................................................ 7
Powering on your computer ......................................................... 7
Powering off your computer ......................................................... 7
Putting your tablet into sleep mode .............................................. 8
Waking up your computer ............................................................ 9
Locking or unlock the screen rotation ................................................... 9
Basic touch screen operations .............................................................. 9
Digital pen operations ......................................................................... 11
3. Windows Interface ........................................................... 13
Start Screen ........................................................................................ 13
Desktop ...............................................................................................14
Customizing your taskbar ........................................................... 15
The Charms menu ..............................................................................16
All Apps ...............................................................................................17
Switching back to Start screen ...........................................................17
3. Setup and Connection ..................................................... 19
Windows Activation .............................................................................19
Configuring your Microsoft Account ....................................................20
Setup your Start screen ......................................................................20
Adding an App ............................................................................20
Removing an App .......................................................................21
Wireless LAN ......................................................................................21
Enabling wireless connection .....................................................21
Connecting to a wireless LAN ....................................................22
Micro SD Card Slot .............................................................................22
To insert your micro SD card ......................................................22
To remove your memory card ....................................................23
Installing the SIM card ........................................................................23
Connecting an External Device ..........................................................25
Connecting to the USB port .......................................................25
Connecting to the HDMI port ......................................................26
4.
Battery ........................................................................... 27
Charging your battery .........................................................................27
Inspecting your battery status .............................................................27
By opening the Charms ..............................................................27
By inspecting the taskbar ...........................................................28
Approximate status of your battery .....................................................28
5. Windows Help and Troubleshooting .............................. 30
Windows Help .....................................................................................30
Troubleshooting ..................................................................................30
6. Specification..................................................................... 35
1. Getting to know your
computer
This chapter provides an overview of the tablet, including the locations of
the connectors and controls, tablet features, and accessories.
Package contents
Carefully unpack your box and take out the items listed as below. If any
of the items is missing or damaged, contact your dealer immediately:
• One Tablet
• One Keyboard duck
• One touch pen
• One AC adapter
• One Warranty card
• This manual
Separating your tablet-laptop
1. Set your tablet laptop on a stable surface.
2. Hold the screen and push down the blue latch.
3. Detach the screen by pulling it upward
Layout
Tablet Views
z Front
No.
Name
Function
Microphone
Mainly for sound and speech recording.
Light sensor
It detects the brightness of the environment.
Front facing
camera
Often for taking self-portraits as well as for video
conferencing.
Digital pen
slot
This is where you can rest and charge the
attached digital pen (optional).
Speaker
The sound system has two speakers for playing
music, notification sounds, and other audio data.
Windows
button
Switches the screen between the Start screen
and the previously opened app/program.
I/O cabinet
Touchscreen
See page 4 for details.
It is a see-touch device: You look at it and also
touch it with your fingers to control the tablet.
z Back
No.
Name
Power lock
Function
Push here to power on/off or lock on/off your
Screen
tablet.
Push here to active or cancel the screen rotating
rotation lock
function.
Rear facing
The camera is mainly used when you are taking
camera
Volume up/
down
photos or recording videos.
Press here to increase or decrease the sound
volume.
z Left
(I/O cabinet)
No.
Name
HDMI port
Function
This is where you can connect your HDMI
Micro SD card
slot
Headphone
external screen.
This is where you can insert a Micro SD memory
card.
Here you can plug in a standard headphone.
connector
USB 3.0 port
Power port
SIM card slot
This is for establishing a USB 3.0 connection.
This is where you plug in the adapter to charge
your tablet.
Insert your SIM card here. (See Chapter 4)
z Bottom
No.
Name
Docking
Connector
Function
A connector to the keyboard dock
Keyboard Duck Views
z Connectors
No.
Name
Docking
Connector
DC Jack
USB 2.0 port
Battery
charging
indicator
and indicators
Function
A connector where you docking your tablet.
A jack to connect the AC adapter that supplies
power to the computer.
You can connect a USB 2.0 device here.
It lights up in amber when the battery is being
charged, and turns into blue when the battery is
fully charged
z Shortcut
keys
You can access certain system settings quickly by pressing the
appropriate function keys.
Press both the Fn key and One of the following shortcut key at the
same time to perform your desired function.
Fn
F1
Enable/disable the
F5
Airplane mode to turn
Increases the volume
level.
off/on all wireless
communication.
F2
Puts your computer
F6
into sleep mode.
Allows you to select your
display mode (an external
monitor required).
F3
Mutes/unmutes the
F7
brightness.
audio output.
F4
Decreases the display
Decreases the volume
F8
level.
Increases the display
brightness.
2. Using your
computer
Powering ON/OFF
Powering on your computer
1. If this is the first time you turn this
computer on, connect the AC
adapter and fully charge the
battery.
2. Press the power button.
3. A logo will appear when the
system is powered on.
Powering off your computer
• Save all your data before powering your computer off.
To power off your system, you can do one of the following:
A.
By Charms
1. Slightly swipe from the right edge of the screen. This opens the
Charms menu. (For more about the Charms menu, see page 16)
2. Click Settings from the menu, and
you will see a menu as shown on the
right,
3. Click Power icon, and select Shut
down.
B. Using the power button
Press and hold the power button for at least four seconds, and you
will see an instruction appears in the middle of the screen, which is
as shown below.
Slide your finger on the screen downward, and the system will
power off itself.
Putting your tablet into sleep mode
When you will be away from your computer for a short time, put the
computer to sleep.
Do one of the following:
• When the keyboard is attached, close the display panel or press Fn +
F2.
• Press the power button.
• Open the Charms and then select Settings → Power → Sleep.
Waking up your computer
Note: It is recommended that you put your computer to sleep
before you move it. Moving your computer while the hard disk is
spinning can sometimes damage the hard disk, causing loss of
data.
Do one of the following:
• Press the power button.
• Press the Windows button.
Locking or unlock the screen rotation
You can find the rotation lock button on the left end of the
screen, as shown on the left.
A first press on the button can lock the screen to keep it
from rotating when you tilt the tablet. And a second press
can unlock the function.
Basic touch screen operations
The monitor is not only a touch screen, but actually also is a tablet. You
can use your fingers or a touch pen to perform many actions on it.
• Don’t use sharp objects to touch the screen. Or, the screen may be
damaged or scratched.
• Don’t touch the touch screen with a conductive material. It may cause a
malfunction.
• The supported functions are application dependent.
Gesture name
Explanation
Tap
Touch once on an item to start an app, open a
link, or perform an optional function. This is
similar to a left-click with a mouse.
Double-tap
Slightly press twice with your finger to select
an item.
Press and hold
Press and leave your finger on an item. This
brings up detailed information or opens a
menu with more options for the item. This is
similar to a right-click with a mouse.
Pinch
Move two fingers together or apart while
touching the screen. This is to zoom in and
or
out on visual apps, such as pictures and
maps.
10
Rotate
Place two or more fingers on an item and then
turn your hand.
This enables you to turn an object.
(Note:
Not all items can be rotated, depending upon
the app.)
Slide
Drag your finger across the screen.
This can scroll through lists and pages, and
can also move an object or be used to draw or
write, depending upon your apps.
Two-finger-slide
Moves up/down, left/right. This is the same
function as scrolling your mouse.
Swipe
Start from any edge of the screen, and then
swipe toward the center of the screen.
Digital pen operations
Your tablet is provided with a touch pen or a
digital pen. With the touch pen, as the one shown
on the right, you can perform all the one-finger
gestures shown in the previous section.
11
With the digital pen, you can perform not only one-finger gestures, but
also more advanced actions with the buttons on it (if supported by apps).
The digital pen has a battery built in. To
charge your digital pen, you need to
rest it in the digital pen slot, which you
can find on the front right of your tablet.
To put your digital pen into the slot,
make sure the side with the golden
connectors facing the connectors in the
slot.
It takes around 20 seconds to fully charge the digital pen.
12
3. Windows
Interface
Start Screen
When you turn on the computer, the Start screen is displayed,
which allows you to access many features and installed
applications (also referred to as apps) at one glance.
Apps
These bricks are the shortcuts for respective
applications.
User Account
The currently used user account.
Charms
See page 16 for detailed information.
13
Desktop
In Windows 8.1, the Desktop is treated as an app. You can find and
activate it from your Start screen and All Apps screen.
Taskbar
Allows you to add toolbars that hold extra
buttons and menus.
Notification
Shows you the current system status and
area
notifications
Program area
This where you can place a shortcut icon for
your desired application.
Charms
See page 16 for detailed information.
14
Customizing your taskbar
Right-click (or press and
hold using your finger) on a
blank part of the taskbar, a
pop-up menu leaps out. In
the menu, select Toolbars
and offer and you can see
following five toolbar
options:
Address
By choosing this, part of your taskbar becomes a
place for typing website addresses where you want to
visit.
Links
This adds quick access to your favorite websites listed
in your Internet Explorer's Favorites menu.
Touch
This is for tablet owners and can add a button that
Keyboard
brings a keyboard to the forefront for touch-typing on
the screen.
Desktop
This adds quick access to all your PC's resources,
allowing you to browse through files, folders, libraries,
network locations, and Control Panel menus without
opening any menus.
New Toolbar
This lets you create a toolbar from any folder's
contents.
15
The Charms menu
This menu consists of five options that are called charms and provide
quick access to various aspects of Windows 8.1.
To display the Charms, do one of the following:
Move the pointer to the upper-right or lower-right corner;
Use one finger to swipe in from the right edge of the screen; or
Press Windows key + C.
The five charms are:
Search
Search for a program or file. Simply enter a keyword in
the Search charm and start search.
It also enables you perform a search within an app or
on the Web.
Share
This charm is for you to transfer and share a picture or
file with another user.
Start
If you are not in the Start screen, this allows you
to return to the Start screen.
If you are in the Start screen, this allows you to
return to the previously screen, which could be
an app or the Desktop.
16
Device
This enables you to operate directly a desired device.
You can import pictures from a digital camera, stream
a video to your TV, or transfer files to a device listed
on the screen.
Settings
This charm enables you to perform basic tasks such
as adjusting the volume, turning off the PC, etc.
All Apps
In the Start screen, touch any blank area and slightly drag upward.
The screen will appear similar to what is as shown below.
Switching back to Start screen
For switching back to the Start screen, do one of the following:
17
z
Move the mouse cursor to the lower-left corner, and click the
Windows icon.
Press the Windows key on your keyboard or tap the Windows
button on your tablet.
Click the Windows icon in the Charms bar.
18
3. Setup and
Connection
Windows Activation
When you turn the computer on for the first time, the Windows activation
screen may appear. Follow the instructions on the screen to register and
active your computer.
If you fail to activate your windows and want to retry again, do the
following:
1. Open the Charms and click Settings > Change PC Settings.
2. Click Activate Windows from the left column.
3. Follow the instructions to activate your windows.
19
Configuring your Microsoft Account
To share files or settings with other devices running Windows 8, you
need to setup a Microsoft Account.
Furthermore, if you want to download or purchase apps from the
Microsoft Store, such Microsoft Account is required.
To setup a Microsoft account
1. Open the Charms and click Settings > Change PC Settings.
2. Click Users > Your account > Switch to a Microsoft account.
3. Follow the instruction to register your account information.
Setup your Start screen
Adding an App
To add an app:
1. Open the All Apps
screen.
2. Drag the top or bottom
of the screen inward,
and an option menu
20
appears at the bottom of
the screen.
3. Touch the icon named Customize
in the menu.
4. Touch the app that you want to add to your Start screen. The
available options will appear in the right side of the option menu.
5. Click “Pin to Start”
to add the app to your Start screen.
Removing an App
To remove an app:
1. In the Start screen or All Apps screen, drag the top or bottom of the
screen inward. An option menu is activated at the bottom of your
screen.
2. Touch the icon named Customize
in the menu.
3. Touch the app that you want to remove from the Start screen. The
available options will appear in the right side of the option menu
4. Click “Unpin from Start”
to remove it from the Start screen.
Wireless LAN
Enabling wireless connection
To do this, do one of the following:
• Press Fn+F1 to activate the wireless networking function.
• Open the Charms and select Settings to open the Network
configuration page, and then toggle the Airplane mode switch to Off.
21
To confirm that Airplane mode is disabled,
go to the desktop and check the
notification area. If you see an airplane
icon displayed on the lower right, then
Airplane mode is on. Otherwise, wireless
function is enabled.
Connecting to a wireless LAN
Once the wireless has been enabled, the computer
automatically scans for available wireless networks
and displays them in the wireless LAN network list.
To connect to your desired wireless network, click
the network’s name in the list, and then click
Connect.
Note: Some networks require a network security key or password for
connection. If necessary, ask the network administrator or the Internet
service provider (ISP) for the required information.
Micro SD Card Slot
You can utilize your micro SD cards as removable disks and conveniently
exchange data with digital devices such as a digital camera, digital
camcorder, MP3, etc.
To insert your micro SD card
1. Insert the micro SD card into the
card slot as shown below.
2. Follow the message appears on
22
the screen, and choose to open
and view files.
3. A Windows Explorer runs and shows all the folders and files in the
micro SD cards, and you can save, move and delete data as you are
handling a storage device.
To remove your memory card
1. Press the card and release. The card will pop up.
2. Pull the card out by holding the end of the card.
Installing the SIM card
Attention: When installing or removing the SIM card, do not touch the
SIM card metal connectors. As a precaution, always hold
your tablet in your hand before you install or remove the
SIM card to avoid electrostatic discharges.
To install a SIM card, do the following:
1. Turn off the system
2. Open the cover of the I/O slot
3. Locate the SIM card slot. To locate the SIM card slot, see “Tablet
layout” on page 4.
4. Hold the SIM card with the metal
contacts facing up, and then insert it
firmly into the SIM card slot until you
hear a click.
5. Close the cover back.
To remove the SIM card, after you turn
23
off the tablet, just pull the SIM card out of the slot.
24
Connecting an External Device
Connecting to the USB port
Your computer comes with two USB ports compatible with USB devices.
The one on the tablet is the latest USB 3.0 port. You can easily identify
the USB 3.0 port by its blue color.
Once you plug a USB device into a USB port on your computer, Windows
automatically loads a driver for that device. After the driver has been
loaded one time, you can disconnect and reconnect the same device
without performing any additional steps.
Note: If Windows requires you to install the driver before connecting.
Check the documentation provided by the device’s manufacturer before
connecting the device.
Before disconnecting a USB storage device, make sure the data
transferring data between your computer and that device has finished.
Click the Safely Remove Hardware icon in the notification area of
Windows to remove the device before disconnecting.
Note: If your USB device uses a power cord, connect the device to a
power source before connecting it.
25
Connecting to the HDMI port
You can connect an external display device such as a monitor, TV,
projector, etc., only if such device has a HDMI port. By doing so, you
have a wider view when you give a presentation or watch a video or
movie.
1. Power off the external device.
2. Locate the mini-HDMI port on your
computer.
3. Connect the small end of the HDMI
cable to the port, and the other end to
the HDMI port on the external device.
4. Power on the external device.
When connecting a TV, you may need
to configure your TV to external
device mode.
5. Select Charms menu > Devices >
Second Screen. An option menu
appears as shown on the right.
6. Select a desired monitor mode.
26
4. Battery
Charging your battery
You can charge your tablet directly
by connecting the adapter to the DC
jack on your tablet and to a wall
socket.
If you dock the tablet into the keyboard dock, the dock will start to
charge the tablet. In this case,
it is recommended to connect
the dock to a wall socket
using the AC adapter.
While system is off, it takes at least 4hrs to fully charged the battery.
Inspecting your battery status
There are mainly two ways to view your battery status.
By opening the Charms
In the Start screen or Desktop, open the Charms menu. A popup window
shows up at the down-left corner of your screen, as show below.
27
In the lower-left corner is the battery status icon.
By inspecting the taskbar
In Desktop, move the cursor to the battery icon in the taskbar. A pop-up
dialog box appears and shows you the remaining battery percentage, as
shown below.
Approximate status of your battery
The battery icon reveals the approximate status of your battery, which
describes as below.
Battery is fully charged
28
Battery is starting to drain
Battery is about to completely
drain, and you should stop using your
tablet and charge it at once.
Battery is being charged.
A battery is an expendable supply, so when using it over a long time, the
capacity/battery life is shortened. If the battery life is reduced to under
half of its initial time, we recommend purchasing a new battery.
When not using the battery for a long time, store the battery after
charging it to 30-40% of its capacity. This extends the battery life time.
29
5. Windows Help and
Troubleshooting
To know how to use Windows 8 properly, it is better to learn how to
use Windows by utilizing Windows Help.
Windows Help
Move the pointer on the screen to the top or bottom right edge of the
screen to view the Charm menu.
Alternatively, drag the right edge inward with your finger to view the
Charm menu.
Select Charm menu > Settings > Help.
For accessing to the most recent online Help, you need to connect
your computer to the Internet.
Troubleshooting
This section describes some common problems and suggested
solutions, and ways to recover your computer from a crash.
Be aware that the problems and solutions described here are meant
only as a guide. They are not definitive problem solving techniques.
For certain problems, you might need help from your reseller or your
service provider.
When you observe a problem, stop operation immediately, because
taking further action might result in data loss or damage. Take a note
of what the system is doing and what actions you performed before
30
the problem occurred. Provide detailed information to your service
provider for quicker problem resolution.
For about any problem, follow these steps:
1. Restart your tablet.
2. Check your Wi-Fi connection.
3. Reset your Wi-Fi connection.
4. Plug your tablet to a wall socket to charge it for at least one
hour.
Display problems
When I turn on the
• If the screen is blank, make sure that:
computer, nothing appears
- The AC adapter is connected to the
on the screen.
computer and the power cord is plugged
into a working electrical outlet.
- The computer power is on. (Press the
power button again for confirmation.)
• If these items are properly set, and the
screen remains blank, have the computer
serviced.
My screen goes blank while
• Your power management is enabled. Do
the computer is on.
one of the following to resume from sleep
mode:
- Press any key on the keyboard. (Cannot
be used in Tablet mode.)
- Press the power button.
- Press the Windows button.
31
Sleep problems
The critical low-battery error
• The battery power is getting low.
message appears, and the
Connect the AC adapter to the computer.
computer turns off
The computer enters sleep
• Make sure that the battery is charged.
mode immediately after
- The operating temperature may be too
Power-on.
hot. Move to a cooler environment and try
to wake the computer.
The computer does not
• If your computer is in sleep mode,
return from sleep mode and
connect the AC adapter to the computer,
the computer does not
then press the Windows button or the
work.
power button.
• If your computer is powered-off, connect
the AC adapter to the computer, then
press the power button to resume
operation.
Display problem
The screen is blank.
• Do the following:
- If you are using the AC adapter, or using
the battery, and the battery status
indicator is on, press Fn+F8 to make the
screen brighter.
- If the power indicator is blinking, press
the power button to resume from sleep
mode.
- If the problem persists, follow the
solution in the next problem “The screen is
unreadable or distorted.”
32
The screen is unreadable or
• Make sure that:
distorted.
- The screen resolution and color quality
are correctly set.
- The monitor type is correct.
Incorrect characters appear
• Are the operating system or programs
on the screen.
installed correctly? If they are installed
and configured correctly, have the
computer serviced.
Sound problems
No sound can be heard
• Make sure that:
from the speaker even
- The Mute function is off.
when the volume is turned
- The combo audio jack is not being used.
up.
- Speakers are selected as the playback
device.
Recovery system problems
Fail to restore system
• The system partition, such as the
partition to factory default.
partition size or the drive capacity of C,
has been modified.
Other problems
Your computer does not
• To turn off your computer, press and hold
respond.
the power button for 10 seconds or more.
If the computer still does not respond,
remove the AC adapter.
• Your computer might lock when it enters
sleep mode during a communication
operation. Disable the sleep timer when
you are working on the network.
33
The connected external
• Do not connect or disconnect any
device does not work.
external device cables other than USB
while the computer power is on.
Otherwise, you might damage your
computer.
• When using a high power consumption
external device such as an external USB
optical disk drive, use an external device
power adapter. Otherwise, the device may
not be recognized, or the system may shut
down as a result.
34
6. Specification
Processor
„ Intel Bay Trail-T 2.4 GHz Quad Core
Memory
„ 2GB
„ DDR3L two channel, 1333MT/s (max.)
Storage
„ 32GB NAND flash
„ eMMC Version 4.51 interface
Dimension
„ 282.0 x 180.0 x 11.4 mm
Weight
„ 750 g
Wireless
„ Miracast support
„ Wi-Fi 802.11 A/B/G/N (5GHz/2.4GHz dual
band support)
„ Bluetooth 2.1+EDR / BT4.0+HS
„ Optional: GPS/GLONASS, 3G, NFC
Display
„ 10.1”, 1366 x 768 (HD)
„ IPS-Pro TFT Color LCD, LED Backlight
„ 10-point touch
„ Win 8 certified touch solutions
Cameras
Battery
„ Front facing camera: 1.26M
„ Rear facing camera: 5.0M
Tablet
„ 2 Cell, 1S2P
„ 31Wh, 8400mAh
„ Model No.: Sunwoda TL10-1S8400-S4L8
Keyboard Dock
„ 2 Cell, 2S1P
„ 15Wh, 2150mAh
„ Model No.: Sunwoda TL10-2S2150-S4L8
35
Input/Output
Tablet
„ 1 x DC-in jack
„ 1 x A-type USB 3.0 port
„ 1 x Mic/head phone jack combo
„ 1 x Micro HDMI port
„ 1 x Micro SD card slot
„ 1 x 3G SIM slot
Keyboard Dock
„ 1 x DC-in jack
„ 1 x A-type USB 2.0 port
Gyroscope
„ Gaming and virtual reality input devices
„ GPS navigation systems
„ I2C/SPI digital output interface
Magnetometer/
„ Compensated compass
Accelerometer
„ Map rotation
sensor
Speaker &
Mic
„ I2C serial interface
„ HDD protection
Speaker :
„ Build-in 2 Speakers
„ 1W x 8 ohm
Mic:
„ 2 x Internal digital MIC
Language
„
„
„
„
„
„
„
„
„
„
Arabic
Brazil Portuguese
English
French
German
Greek
Hebrew
Hungarian
Italian
Latin Spanish
36
„
„
„
„
„
„
„
AC-Adapter
Portuguese
Russian
Simplified Chinese
Spanish
Thai
Traditional Chinese
Turkish
„ DC Output: 12V/24W
„ Input Voltage: 100–240VAC Nominal
„ Input Frequency: 50–60Hz.
Model No.
„ Asian WA-24R12Fy (y=U,G,K,B,A)
Certification
„ CE /FCC/CCC
EMC
„ FCC&SAR / R&TTE&SAR
RF
„ UL / CB
„ CCC
Safety&
„ WEEE
Environment
„ RoHS
„ Energy Star 5.2
„ EUP LOT6
„ Vibration test :
MIL-STD-810F/EN-60068
„ Drop test : MIL-STD-810F
/GB/T4857
„ Acoustic test :
Others
ISO3745/ISO7779
„ GB 28380-2012 (For
China Only)
„ Water resistant: IP41
37

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2014:07:21 17:40:45+08:00
Creator Tool                    : Microsoft® Office Word 2007
Modify Date                     : 2014:07:29 10:56:17+08:00
Metadata Date                   : 2014:07:29 10:56:17+08:00
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Format                          : application/pdf
Creator                         : apple
Title                           : Manual (system).pdf
Document ID                     : uuid:d309adf6-a887-4a6b-9200-0b1be9b61e5c
Instance ID                     : uuid:6effbe02-f247-4512-a313-38736ccbea69
Page Count                      : 46
Author                          : apple

EXIF Metadata provided by EXIF.tools