Huawei Technologies U3310 WCDMA/GPRS/GSM/EDGE Mobile Phone with BT User Manual U3300

Huawei Technologies Co.,Ltd WCDMA/GPRS/GSM/EDGE Mobile Phone with BT U3300

User Manual Part 2

62Getting Started Loading the SIM CardLoad your SIM card before using your phone. To use the SIM card properly, please read the following instructions carefully. Note • Keep the SIM card out of the reach of chil-dren.• The SIM card and its metal contacts can be easily damaged by scratching or bend-ing. Ensure care when you carry, load or remove it.• Always disconnect the charger from the phone before loading or removing the SIM card.To load the SIM card, do as follows: 1Position the card at the card slot entrance, mak-ing sure it is facing the same way as shown in the diagram below, with the notched corner at the down right. Then slide in as shown. 2Fit the battery into the battery slot on back of the phone. Press the battery down until it clicks into place. 3Slide the back cover to the phone.
Unloading the SIM Card7Getting Started2 Unloading the SIM CardOnly unload the SIM card and the battery after pow-ering off your phone. Otherwise, your phone may be damaged.To unload the SIM card: 1Unload the back cover out of the phone. 2Please unload the battery according to the fol-lowing picture. 3Press the SIM card with one finger and slide it out of the slot. Charging the BatteryBefore charging the battery, please read the following precautions carefully. Note • When you charge the battery for the first time, please charge it for a minimum of 12 hours.• The battery discharges even while not being used. If you have not used it for a long time, please recharge it first.• The charging time depends on the envi-ronmental temperature and the age of the battery.• The battery can be recharged but eventu-ally wears out. If the battery lasts for a shorter time period than usual after being
Loading/Removing a Memory Card8charged normally, replace it with a battery of the same type.• Do not strike, throw or cause any kind of violent shock to the battery, otherwise liq-uid leakage, body damage, overheating, explosion or fire may occur.• Charge the battery by using the charger supplied with your phone.Charging with a Cable ChargerBefore charging the battery with a cable charger, ensure that the battery has been properly loaded into your phone.To charge the battery, do as follows: 1* Insert the plug of the charger into the connector of the phone as shown in the following figure. 2Plug in the connector of the charger to a power socket. Note • *The plug of the charger is in trapezium shape. Reversely inserting the plug may damage the mobile phone and charger.The connection methods of USB data cable and headset are the same as the charger.• When the battery power level is very low, the phone makes alert sounds and dis-plays a prompt. When the battery power level is too low, the phone will power off automatically.• When the battery is being charged, the charging indicator blinks continuously. When the charging indicator stops blink-ing, it indicates that the battery is full. Loading/Removing a Memory CardYour phone supports a memory card (micro-SD) with a capacity up to 2 GB. 1Insert the memory card into the slot, as shown in the following figure.With the metallic conect downward
Powering On/Off9Getting Started2 2To remove a memory card, press the memory card gently. Now the memory card will pop up automatically. Then take it out as shown in the following figure. Powering On/OffPowering OnEnsure that the SIM card is in your phone and that the battery has been charged.Press and hold to power on your phone.Powering OffPress and hold to power off your phone.Access CodesIf you have set the phone password and the PIN is ON, you have to enter the corresponding access codes when you power on your phone. For setting and changing the access codes, please refer to "Set-tings/Security Setup" on page 50.◆ Phone PasswordThe phone password is used to protect your phone from unauthorized use. The phone password is preset as 0000 for your phone.◆ PINThe personal identification number (PIN) code is used to protect your SIM card from unauthorized use. The PIN code is usually provided when you get the SIM card from your server provider. If you have not received a PIN code or if you have forgotten it, con-tact your local customer care centre.
Powering On/Off10◆ PIN2Some SIM cards provide a PIN2 code. Some special functions such as the "Fixed Dialer Number" are not available until you enter the PIN2 code. At the same time, your SIM card should support these functions.◆ PUKTo unlock a locked SIM card, you need to enter the PIN Unblocking Key (PUK) code. The PUK code is usually provided when you get the SIM card from server provider. If you have not received a PUK code or if you have forgotten it, contact your local customer care centre.◆ PUK2Some SIM cards provide a PUK2 code that is used to unlock a locked PIN2 code. The PUK2 code is usu-ally provided when you get the SIM card from server provider. If you have not received a PUK2 code or if you have forgotten it, contact your local customer care centre.
113Call Service Making or Answering CallsMaking a Video CallYou can make a video call to other person whose phone also supports video calls. 1Enter or edit a phone number in one of the fol-lowing ways:• Enter a phone number through the keypad.• Select a number from the Calls screen.• Select a number from the Contacts screen. 2Select Options > Call > Video Call to dial. 3Press to end the video call. Note To delete a wrong number, press once to delete the digit to the left of the cursor.Making a Voice Call 1Enter or edit a phone number in one of the fol-lowing ways:• Enter a phone number through the keypad.• Select a number from the Calls screen.• Select a number from the Contacts screen. 2Press to dial. 3Press to end the call.Making Voice Calls Using SDNYou can make a voice call through speed dialing. For instructions on assigning speed dialing numbers, refer to "Contacts/Other Operations" on page 17.To make a call by speed dialing number (SDN), press and hold the number key until the phone dials the corresponding phone number.Answering or Rejecting CallsYou can set the answer mode to Any key, Send key or Slide up. For details, refer to "Settings/Call Set-tings/Answer Mode".The following describes how to answer or reject a call in different answer modes:
Operations During a Voice Call12 Note When the phone is closed and there is no ongoing call, you can press and hold the camera key to mute the ringtone of an incoming call. You can also press and hold the volume keys to reject the call.You can also set the auto answer mode to Immedi-ate answer, Text message or Recorded voice.For details, refer to “Settings/Call settings/Auto Answer”. Operations During a Voice CallIcon Description: A call is ongoing.: The call is on hold.OperationsDuring a voice call, you can select Options to per-form the following operations.• Hold active call/Resume: To hold or resume the call during a call.• End: To end all calls, the active call, the current call or the on hold call.• Handfree/Earpiece: To switch between the Hand-free and the Earpiece modes during a call.Operation DescriptionAnswera call• If the answer mode is Slide up, slide the phone.• If the answer mode is Any key, press any key except .• If the answer mode is Send key, press .• If the headset is in use, press the con-trol key on the headset.Rejecta callPress or select Options > Reject.End a call • If the headset is not in use, you can close the phone or press .• If the headset is in use, press the con-trol key of the headset.Reply by messageTo send a predefined message to the caller.
Operations During a Video Call13Call Service3• Start recording/Stop recording: to record or stop recording the conversation.• Other Applications: To access he Contacts screen, the Messaging screen, the Calls screen or the Calendar screen.• Answer/Reject: Your phone allows you to handle two calls simultaneously. During a call, if there is a new incoming call, select Options > Answer to answer it or select Options > Reject to reject it.• Swap: To swap between calls during a 3-party call.• Conference call/Private call: To switch to the con-ference call during a 3-party call or to talk with a party privately during a conference call. Operations During a Video CallIcon DescriptionOperationsDuring a video call, you can press to hold the call and send a preset file to the other party. You can press again to resume the call. Before you use the function, you can preset a file in settings/video call/Send image.During a video call, you can select Options to per-form the following operations.• Camera on/Camera off: To allow or forbid the video from your side.• Audio on/Audio off: To allow or forbid the audio from your side.• External view/Internal view: To switch between the main lens and the assistant lens.Icon DescriptionPress the up or down scroll key to adjust the brightness.Press the left or right scroll key to zoom in or zoom out.Press the volume keys to adjust the vol-ume./Press to switch between the loud-speaker mode and the earpiece mode.Icon Description

Navigation menu