Humax T1 11n Wireless Roaming Router User Manual IP04305

Download:
Mirror Download [FCC.gov]
Document ID	3284485
Application ID	R6NrqSuQFVhguGWvPVEKaw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	43.19kB (539914 bits)
Date Submitted	2017-02-15 00:00:00
Date Available	2017-04-01 00:00:00
Creation Date	2017-12-22 09:37:26
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-12-22 09:37:26
Document Title	IP04305_说明书
Document Creator	Adobe Illustrator CS6 (Windows)

Use it as Router
LEDs on the Front Panel
After the product is successfully registered on the network, the LEDs illuminate continuously to indicate
that the product is active and fully operational.
Warning
Electrical Outlet
Quick Start Guide
3. Powering On
1. Connect all devices before you plug any power cords into the electrical outlet.
1. Plug in the AC power adaptor from the power connector to an electrical outlet.
2. Always turn off the product and network devices before you connect or disconnect any cables.
2. If the power successfully turns on, a white light on the power LED is turned on.
3. Hazardous electrical voltages can exist on the product and peripheral devices and can be present on
any connected cables.
Note: Use only the AC power adaptor provided in this product. Using other
adaptors may damage the product.
Wireless or Wired, it's 11n Wireless
LED
Operation
Power
Internet
White On
Power is on.
White On
Internet is connected.
White Blinking
Firmware update is in progress.
Internet is not connected.
Roaming Router
White On
QUANTUM T1
Network is connected wirelessly.
2 minutes.
White Slow Blinking
White Fast Blinking
Blue On
Wireless
2. Checking the Mode
Blue Slow Blinking
Your product has the Q-MODE switch.
Blue Fast Blinking
Check that the switch is set to ROUTER.
2 minutes.
Wi-Fi is not available.
White On
Ethernet
Networking device is connected to the LAN port.
No device is connected to the LAN port.
Internet, Wireless, Ethernet Blinking
Resetting the system is in progress.
Note: Blue light is turned on when the roaming & mesh network is successfully configured over HUMAX
products.
Modem
T1 Router
Internet
Q-MODE
Your product supports Q-MODE that enables operating as a router or an extender.
4. Connecting the Network Devices
It’s very simple to change the operation mode. Just slide the Q-MODE switch to ROUTER or EXTENDER.
Then, the mode change is automatically completed.
You can connect your network devices to the router over wired or wirelessly.
PC
1-1
Use Ethernet cables to connect your devices to the router over a wired
Ethernet connection.
Mobile Phone
1. Connecting the Internet
1-2
You can connect your product to the Internet over a direct WAN or through a modem.
1-1 If you access Internet by the modem such as ADSL, VDSL, cable and FTTH, plug
one end of the Ethernet cable to the Internet port of your product and the other
end to the LAN port of your modem.
1-2 If you access the Internet by WAN broadband, plug the Ethernet cable to the
Internet port of your product.
Note: We recommend you to connect entertainment devices such as OTT,
gaming console and IPTV to the Entertainment ports. The ports have
the priority in transmitting multimedia data without transmission delay
or interruption.
BOTH
Gaming Console &
Media Sharing
*Roaming Mode
*Mesh Mode
Use it as Extender
ROUTER
Router Mode
WISP Mode
EXTENDER
AP Mode
Repeater Mode
Media Bridge Mode
Electrical Outlet
Internet Connection
You can configure the network over a wired Ethernet connection or wirelessly.
2. Powering On
1. Changing the Mode
Wired
Connect the Ethernet cable between the PC and the LAN port of your product.
Your product has the Q-MODE switch.
Slide the switch to EXTENDER.
Wireless
1. Open the web browser.
2. Enter http://dearmyrouter.net to the address bar, and then press the Enter key.
- With HUMAX QUANTUM Series,
you will experience seamless Wi-Fi network at any moment.
- T1, T2, T3, T3A, X1 and X3 support both roaming & mesh network, and T5, T7 and
T9 support roaming network only.
- Roaming & mesh feature is con฀gured over HUMAX products. (*)
3. The default ID and password are admin and nnnn. nnnn is the last 4 digits of serial number.
Refer to the serial number at the bottom of your product.
Extender has wireless connectivity
with a third party router
WPS
Note: We recommend you to change the ID and password to secure your network.
Go to Management > Change Password to change your password.
* Roaming & mesh network is configured
over HUMAX products
Welcome to QUANTUM T1!
T1 Extender
192.168.1.1
You can configure WPS between the extender and the router.
3-1 Press the WPS buttons on both devices within 2 minutes. When WPS is
successfully configured, the blue light blinks on the Wireless LED.
Scan the QR code
to access @@ on your mobile device.
Note: If you use another router other than HUMAX product, the white light
blinks on the Wireless LED, which means your extender is in repeater
mode.
3-2 Check the network when the connection is complete.
If you connect the extender to a HUMAX router, both network
names are the same as if they configure a single network. But,
if you use a router other than HUMAX products, the network
name of your extender will copy the router›s name following
Ext2G or Ext5G. (ex. Router_Ext5G)
Model: QUANTUM T1
Code: 4-00021
http://dearmyrouter.net
123456789
ID
admin
Power Input: 12V
, 0.5A
123456789
S/N: QT1YYWWnnnnnn
Password
****
Mac: DCDC8321000001
Login
※
For the default ID and password, see the bottom of the product.
Router Login:
http://dearmyrouter.net
ID: admin
Password: nnnn
SSID: We Love You So Much
Password: humax_nnnn
Designed by Humax (Korea)
Made in China
※Please change Login Password and Wi-Fi Password for Security.
When you log in to the router for the first time, the installation wizard will appear. Then, follow the steps to configure the network.
3. Wireless Network Setting
Router Mode
Enter your own network name and password to change the default settings. You can secure your
wireless network from unauthorized users.
1. Welcome
Click Start. The system will check automatically if your router is connected to the Internet.
2-1. Roaming & Mesh
WISP Mode
Just press the WPS buttons on HUMAX products within 1 second. Then, they are connected each
other automatically, and configure the mesh network. You will experience seamless Wi-Fi roaming
over the mesh network.
You can use wireless Internet service in Router mode.
1. Log in to dearmyrouter.net, and then go to Management > WISP Mode.
Wireless Setting
2. Set the WISP mode to On, and select your Internet service provider.
Roaming & Mesh Setting
Welcone to Quantum T1 !
WISP Mode
This is Quantum T1,






In this mode, all Ethernet ports are bridged together and the wireless client will connect to ISP access
point. The NAT is enabled and PCs in Ethernet ports share the same IP to ISP through wireless LAN.
2.4GHz
Complies with 11n Wi-Fi standard.
Wi-Fi 300 Mbps speed.
Provides WEP 64/128-bit, WPA, WPA2 and WPA-Mixed security.
Supports Guest Network ,QoS, Parental Control, VPN, WPS etc.
Supports Smart Roaming for Mobile Client.
Supports Power Saving, LED Control, System Restart for energy saving.
On/Off
We Love You So Much
Network Name (SSID)
CH
RSSI
Security
MAC Address
Band
We Love You So Much
-45
WPA2-PSK
BC:76:70:7C:5C:74
2.4GHz
TIANA_89
-47
WPA2-PSK
F8:D1:11:5C:84:BA
2.4GHz
ASUS
-51
WPA2-PSK
70:7C:F8:D1:11:55
2.4GHz
Wafya
-26
None
11:5C:54:D8:33:98
2.4GHz
NETGEAR
-51
WPA2-PSK
70:7C:F8:D1:11:55
2.4GHz
iptime
-77
WEP
5C:74:31:AB:C1:D2
2.4GHz
Next
Start
4. Password Setting
•
We recommend you to update the firmware to the latest version when available.
If the existing configured, pressing the WPS button on the Mesh Network products
and add new products are the closest connection automatically.
**********
Previous
If you want to skip the installation wizard, click Skip. This button is available always during
installation wizard.
Refresh
Select the device and enter the password to connect the host device.
Password
? About wireless security and password. view more
•
Tip!
Minimizing the walls, furniture, appliances, etc. to connect between the two products,
and the products work best when operating at up to 12m (40 feet) inside and outside.
Network Name (SSID)
You can more easily set various functions through web UI and experience fabulous router.
Do you want to start the wizard for easy setup?
Note:
HUMAX each other two products that you want to connect to, you can simply Extended Network via the WPS button.
Place the product on where to actual use, press the WPS button on your product.
Password
WPS
**********
Start WPS Process...
Enter your ID and password to change the default password. You can enhance the security on your
network environment.
Back
Connect
Previous
Change Password (Optional)
2. Internet Setting
2-2. Repeater
You can connect the Internet automatically or manually depending on your Internet connection type.
Note: This page appears only when your product is not connected to the Internet.
Extender Mode
If you change the password, you can make your network more secure.
For the default ID and password, see the bottom of the product.
Slide the Q-MODE switch to EXTENDER.
The changed password will be applied from the next login.
Internet Setting
Connection Type
Dynamic IP
Repeater Setting
Login ID
admin
Current Password
**********
New Password
**********
Retype New Password
**********
You can manually configure your connection settings.
If you do not know the Internet connection type, please contact your ISP.
Previous
Select a device from the list below and enter the password to connect to the host device.
Using the WPS button on both devices, you can easily connect them.
If you want to configure the network over a wired Ethernet connection, plug the Ethernet cable into the WAN Port
of the host device. In this case, the host operates automatically in Bridge mode.
WPS
Next
5. Summary
When you complete your network settings, the information on your network will display.
Previous
Next
Summary
Select the connection type your ISP is using. In most cases, it will be Dynamic IP.
•
Dynamic IP: The Internet will be connected automatically.
•
Static IP: Enter the IP address, Subnet mask, Gateway and DNS server supplied by the ISP.
•
PPPoE: Enter the user name and password supplied by the ISP.
•
PPTP or L2TP: Enter the user name, password and VPN server supplied by the ISP.
Connection Type
Dynamic IP
Internet Setting
Dynamic IP
100.1.1.1
255.255.255.0
192.168.1.1
0.0.0.0
0.0.0.0
Connection Type
WAN IP Address
Subnet Mask
Gateway
Primary DNS
Secondary DNS
Next
Wireless 2.4GHz
100.1.1.1
Network Name (SSID)
CH
RSSI
Security
MAC Address
Band
IPTime Zone
-45
TIANA_89
-47
ASUS
Wafya
iptime
Previous
 T1 works automatically in AP mode if you connect it to a router over a wired Ethernet cable and use a
client device wirelessly.
 T1 works automatically in media bridge mode if you connect it to a router wirelessly and use a client
device over a wired Ethernet cable.
 T1 works automatically in repeater mode if you connect it wirelessly to a router other than a HUMAX
router and use a client device wirelessly.
 If T1 works together with a HUMAX router, the roaming & mesh network is configured over the
products.
WPA2-PSK
BC:76:70:7C:5C:74
2.4GHz
WPA2-PSK
F8:D1:11:5C:84:BA
2.4GHz
-51
WPA2-PSK
70:7C:F8:D1:11:55
2.4GHz
-26
None
11:5C:54:D8:33:98
2.4GHz
-77
WPA2-PSK
5C:74:31:AB:C1:D2
5GHz
Password
Back
**********
Next
We Love You So Much
Password
If your router is successfully connected to the Internet, the information on the internet connection will
display.
Previous
Internet
IP Address
Note: For more information on the Internet connection, refer to the web manual at
www.humaxdigital.com/QUANTUM.
Network Name (SSID)
T1 operates as an extender, and configures the roaming & mesh network with a HUMAX router.
▼
? What is the Dynamic IP/Static IP/PPPoE/PPTP/L2TP? view more
If you have a networking device other than HUMAX products, select it from the list and then enter
the password. You will experience stronger and wider Wi-Fi signal.
humax_0000
Done
FCC warning:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
1. Welcome
Home
If you configure the network with HUMAX
products only, click HUMAX Products and go to
2-1. Roaming & Mesh.
If you use a third party product other than
HUMAX, click Other Products and go to
2-2 Repeater.
Welcome to Extended Network
After completing the network settings, go to Operation Mode. In this page, you can see the current
status of your product.
Home
This page shows the current status and some basic settings of the device.
Your product has changed to Extender mode. In this mode, you can expand Wi-Fi coverage.
If you want to configure the network over a wired Ethernet connection,
plug the Ethernet cable into the WAN port of your product.
In this case, the product operates automatically in Bridge mode.
2.4G
Select a product you want to connect wirelessly.
Dynamic IP
10.10.10.1
HUMAX Products
QUANTUM T1
SanULTRA DUAL_1
Other Products
Internet
Next
Operation Mode
Router Mode
Connection Status
Dynamic IP
IP Address
183.99.19.131
Subnet Mask
255.255.255.128
Gateway
183.99.19.129
DNS Server
168.126.63.1/168126.63.2
MAC Address
F4:28:53:35:C3:F9
4 Devices

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:4c1b0774-a119-11f2-0000-02c7314339d4
Producer                        : GPL Ghostscript 9.18
Modify Date                     : 2017:07:15 01:27:21Z
Create Date                     : 2017:07:15 01:27:21Z
Creator Tool                    : UnknownApplication
Document ID                     : uuid:4c1b0774-a119-11f2-0000-02c7314339d4
Format                          : application/pdf
Title                           : Untitled

EXIF Metadata provided by EXIF.tools