Hunter Douglas Window Fashions 1DX Communications Module User Manual Rev 3
Hunter Douglas Window Fashions Communications Module Users Manual Rev 3
Users Manual Rev 3
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3391257 |
| Application ID | ew1+93FWlID9s46nDbv+Vw== |
| Document Description | Users Manual Rev 3 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 21.92kB (274057 bits) |
| Date Submitted | 2017-05-15 00:00:00 |
| Date Available | 2017-05-15 00:00:00 |
| Creation Date | 2017-04-15 08:10:41 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2017-04-15 08:10:41 |
| Document Title | Users Manual Rev 3 |
| Document Creator | Microsoft® Office Word 2007 |
| Document Author: | Baugh, James |
Confidential 1DX Installation Manual FCC ID of this product is as follows. FCC ID: UXU1DX IC No. of this product is as follows. IC : 7316A-1DX For OEM integration only – device cannot be sold to general public. Therefore we will ask OEM to include the following statements required by FCC and IC on the product and in the Installation manual Notice. Contents 1.Voltage 2.Antenna 3.Notice Copyright © Hunter Douglas Window Fashions All rights reserved. 28 April 2016 Confidential 1.Supply Voltage min. typ. max. unit Specification Temperature Range -40 +25 +85 deg.C Specification Voltage VBAT 3.0 3.6 4.8 VDDIO 1.71 1.8or3.3 3.63 Copyright © Hunter Douglas Window Fashions All rights reserved. 28 April 2016 Confidential 2.Antenna ■Please perform the antenna design that followed the specifications of the antenna. The concrete contents of a check are the following three points. １）It is the same type as the antenna type of antenna specifications. The trace reference design section is provided under a separate non-disclosure agreement ２）An antenna gain is lower than a gain given in antenna specifications. Measure the gain, and confirm the peak gain is less than the application value (1.4dBi) ３）The emission level is not getting worse. Measure the spurious, and confirm degradation of less than 3dB than spurious value of worst of report used for the application. However it is spurious defined below. Please send those reports to Hunter Douglas. Copyright © Hunter Douglas Window Fashions All rights reserved. 28 April 2016 Confidential 3.Notice For OEM integration only – device cannot be sold to general public. Therefore we will ask OEM to include the following statements required by FCC/IC on the product and in the Installation manual Notice. Please describe the following warning on the final product which contains this module. Contains Transmitter Module FCC ID: UXU1DX or Contains FCC ID: UXU1DX and Contains IC: 7316A-1DX Copyright © Hunter Douglas Window Fashions All rights reserved. 28 April 2016 Confidential 3.Notice ●Please describe the following warning to the manual. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. ※When the product is small, as for these words mentioned above, the posting to a manual is possible. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) l’appareil ne doit pas produire de brouillage; 2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. ※When the product is small, as for these words mentioned above, the posting to a manual is possible. Copyright © Hunter Douglas Window Fashions All rights reserved. 28 April 2016 Confidential 3.Notice ●When installing it in a mobile equipment. Please describe the following warning to the manual. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body. Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain. RF Exposure requirements are met when installed in mobile equipment. This module cannot be installed in portable equipment without further testing and a change to FCC's grant of authorization. Contact Murata regarding portable applications. Copyright © Hunter Douglas Window Fashions All rights reserved. 28 April 2016 Confidential 3.Notice ●When installing it in a portable equipment. It is necessary to take a SAR test with your set mounting this module. Class II permissive change application is necessary using the SAR report. Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm. Copyright © Hunter Douglas Window Fashions All rights reserved. 28 April 2016 Confidential 3.Notice This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. 3)The use of an antenna with gain less than 1.4 dBi. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1)L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les utilisateurs, et 2)Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Tant que les 3 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé. Copyright © Hunter Douglas Window Fashions All rights reserved. 28 April 2016 Confidential 3.Notice IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: UXU1DX”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Copyright © Hunter Douglas Window Fashions All rights reserved. 28 April 2016 Confidential IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 7316A-1DX ”. Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 7316A-1DX". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel. Copyright © Hunter Douglas Window Fashions All rights reserved. 28 April 2016 10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 10 Language : en-US Tagged PDF : Yes Author : Baugh, James Creator : Microsoft® Office Word 2007 Create Date : 2017:04:15 08:10:41-06:00 Modify Date : 2017:04:15 08:10:41-06:00 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools