Hunter Douglas Window Fashions SIL1 Motor Control User Manual Users Manaul

Hunter Douglas Window Fashions Motor Control Users Manaul

Users Manaul

Instructions for PV4 Assembly 23mm Motor 31mm Motor
Connect the Power Source ■ Refer to the appropriate section below based on your order. ➤ For a battery wand, see “If You Have a Battery Wand...” below. ➤ For an optional DC power supply, see “If You Have a DC Power Supply...”. If You Have a Battery Wand... Install Batteries Into the Battery Wand NOTE: Hunter Douglas recommends AA alkaline batteries for use with our battery-powered assemblies. These will provide more than one year of operation, depending on usage. Lithium and rechargeable batteries are not recommended. ■ Squeeze the cap latch to release and remove the cap. ■ Install the batteries according to the instructions on the battery wand label. ■ Replace the cap. ➤ Align the tab with the end of the wand. ➤ Press the cap on until it latches. Plug the Power Cable into the Battery Wand ■ Connect the power cable (coming from the end of the motor) into the socket on the battery wand. If You Have a DC Power Supply... Connect the Power Supply ■ Plug the power cable from the motor into the extension cable. ■ Plug the other end of the extension cable into the DC power supply. ■ Plug the DC power supply into a standard outlet. WARNING: Keep cords and small parts out of the reach of children. They can wrap cords around their necks and STRANGLE. They can also put small parts in their mouths and CHOKE. WARNING: Electric shock and/or a fire hazard may occur if the DC power supply and cables are not properly installed. Operate the Assembly Check the Power Cord ■ Check to ensure the power cord is not pinched. Test the Assembly Using the Manual Control Button Testing the shade with the manual control button will allow you to ensure that the motor and power source are working correctly. Press the manual control button to test operation ➤ Press the button to alternately rotate motor, stop, and rotate the other way. Manual control button
Test the Assembly Using the Remote Refer to the PowerView™ Remote Guide for more information To link a shade to a remote: 1. Press and hold Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in program mode. 2. Press and hold the manual control button on the 3. While continuing to press the manual button, press been linked to the network. 4. Press and hold Stop for six seconds to exit program mode.To join a shade to a GROUP: 1. Press and hold Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in program mode. 2. Press desired group number (1 – 6) on the remote.selected. 3. Press and hold the manual control button on the 4. While continuing to press the manual button, Press has joined the group. 5. Press and hold Stop for six seconds to exit program mode.To remove a shade from a group: 1. Press and hold Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in program mode. 2. Press desired group number (1 – 6) on the remote. The light for the group number selected will pulsate to show it is selected. 3. Press and hold the manual control button on the 4. While continuing to press the manual button, Press removed from the group. Radio Control Operation Once the assembly has been joined to a group, radio control is used to operate the toward the assembly being operated. Multiple assemblies Remote Functions: 1. To wake up remote, press Stop. The last group(s) selected will be highlighted and active.2. Press “All” or Groups 1‐6 to select specific shade(s) to move. Selected a. Multiple Group number may be selected at a time.b. To deselect a Group, press the Group number again. The light for that group will go out.3. Select the OPEN button to move the motor in one direction4. Select the CLOSE button to move the motor in the other direction5. While a motor is in motion, press OPEN or Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in Press and hold the manual control button on the assembly. While continuing to press the manual button, press Stop on the remote. The motor will rotate slightly for six seconds to exit program mode. Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in 6) on the remote. The light for the group number selected will pulsate to show it is Press and hold the manual control button on the assembly. While continuing to press the manual button, Press Open on the remote. The motor will rotate slightlyStop for six seconds to exit program mode. Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in 6) on the remote. The light for the group number selected will pulsate to show it is Press and hold the manual control button on the assembly. While continuing to press the manual button, Press Close on the remote. The shade will jog to indicate it has been been joined to a group, radio control is used to operate the motor. There is no need to aim the remote assemblies can be operated at the same time. Stop. The last group(s) selected will be highlighted and active. 6 to select specific shade(s) to move. Selected groups will light to show they are selected.a. Multiple Group number may be selected at a time. To deselect a Group, press the Group number again. The light for that group will go out. move the motor in one direction. move the motor in the other direction. OPEN or CLOSE, the opposite of motor motion to reverse direction.Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in rotate slightly to indicate it has Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in The light for the group number selected will pulsate to show it is rotate slightly to indicate it Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in 6) on the remote. The light for the group number selected will pulsate to show it is e. The shade will jog to indicate it has been . There is no need to aim the remote groups will light to show they are selected. motion to reverse direction.
U.S. Radio Frequency FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may causeThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Freasonable protection against harmful interference in a resideinstalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, thernot occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, wequipment off and on, the user is encouraged to try to correct the interference b• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority tIndustry Canada Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for tIndustry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be spower (e.i.r.p.) is not more than that necessary for successful communication.This device complies with Industry Canada licence‐exempt RSS standard(s). Operation is subject to the following two conditioninterference, and (2) this device must accept any interference, including interference that may cause undesired operation of Industrie Canada Conformément à la réglementation d’Industrie Canada, le présent émettapprouvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intentiond’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessairsatisfaisante. Le présent appareil est conforme aux CNR d’Industrie Canada applicasuivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillasusceptible d’en compromettre le fonctionnement. European Conformity We, the undersigned, Hunter Douglas Window Fashions Address: One Duette Way, Broomfield, CO 80020, USA Authorized representative in Europe: Nico Dekker Hunter Douglas Europe B.V. Piekstraat 2, 3071 EL Rotterdam, The Netherlands certify and declare under our sole responsibility that the PV4 1999/5/EC. A copy of the original declaration of conformity may be found at Location of FCC label on Location of FCC label on assembly This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfnot occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.a regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for tIndustry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisird’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le b assembly conforms with the essential requirements of the EMC directive 2004/108/EC and eclaration of conformity may be found at www.hunterdouglas.com/RFcertifications. Location of FCC label on assembly Location of FCC label on assembly CC Rules. These limits are designed to provide ntial installation. This equipment generates, uses and can radiate radio frequency energy and, if not e is no guarantee that interference will hich can be determined by turning the o operate the equipment. a regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by o chosen that the equivalent isotropically radiated s: (1) this device may not cause the device. eur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) des autres utilisateurs, il faut choisir le type e à l’établissement d’une communication bles aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions ge radioélectrique subi, même si le brouillage est EMC directive 2004/108/EC and R&TTE directive

Navigation menu