Hunter Fan TX13 Remote Control for Ceiling Fan and Attached Lamp User Manual 41475 01

Hunter Fan Company Remote Control for Ceiling Fan and Attached Lamp 41475 01

Contents

User Manual 85094

Form # 41475-01 Rev. 1-23-2001Hunter Fan CompanyRemote Ceiling Fan& Light Control®Transmitter Model: 85095Transmitter Battery: 12 V, Type 23A, MN-21 or equivalentReceiver Model: 85069Ratings: 120 VAC, 60 Hz,1.0 Amp FanReceiver Weight: 8 oz.300 Watts incandescent lightNotes:1. This device complies with Part 15 of the FCC Rules. Operation is sub-ject to the following two conditions: (1) this device may not causeharmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation.2. This equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment gen-erates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harm-ful interference to radio communications. However, there is no guar-antee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or televi-sion reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference byone or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different fromthat to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.3. For use only with electrically reversible ceiling fans rated at 1.0 amp orless, and fan incandescent light kits rated at 300 watts or less.4. Not for use with shaded-pole or non-reversible motors. Not recom-mended for use with the Hunter Original®.Before Installing the Control:1. Use the pull-chain switch to set the fan speed to the HIGH positionbefore installation. Do not use the pull-chain to change the fan speedafter installation, as damage to your ceiling fan or control may result.The speed of the fan should only be changed by the control.2. Set the ceiling fan light kit to the ON position before installation. Thelight level should only be changed by the control.Receiver Installation:1. Disconnect power to the ceiling fan and light kit at the main electricpanel. Remove fuse or move circuit breaker to the OFF position. Turnoff wall switch.2. IMPORTANT! Before installing this control, change the factory defaultjumper switch settings to your own unique code. Refer to Figure 1.Using small pliers or tweezers, pull out one or more of the three jumperswtiches by clamping on the small metal strip. Place the jumperswitches in the desired spots. Be sure the jumper switch positions ofthe transmitter and receiver match, or the ceiling fan will not func-tion. Select different combinations of jumper switches to prevent mis-operation due to other remote control fans, garage door openers, etc.3. Install the ceiling fan according to its instructions, up to the point ofmaking the electrical connections.4. Use the 2 large wire nuts supplied to connect the receiver and housewiring, then use the 3 small wire nuts supplied to connect the receiverand ceiling fan wiring. Refer to the Wiring Diagram in Figure 2.Caution: Risk of Electrical Shock!All wiring must be performed in accordance with national and local electri-cal codes. If you are unfamiliar with the wiring codes, you should use aqualified electrician.To avoid overheating and possible damage to other equipment, do notinstall to control a receptacle, fluorescent light fixture, motor operated ap-pliance, or transformer-supplied appliance. Use only to control one paddle-blade ceiling fan and incandescent light fixture.Read and Save these InstructionsCeiling PlateReceiverCanopyFigure 3 - Installing ReceiverJumperSwitchTransmitterJumperSwitchBack ReceiverBackFigure 1 - Jumper SwitchesFigure 2 - Wiring DiagramLightKitBlack /WhiteBlack WhiteFan CommonAntenna120 V ACPowerInWhite MainBlack Main5. Install receiver as shown in Figure 3. Line up slots on the receiver withthe ceiling plate. Be sure to push wire connections from the ceilingback up through the hole in the ceiling pate. Wires attaching fromthe ceiling plate to the fan should be placed inside the canopy underthe receiver. Once the receiver is installed, continue with the appro-priate instructions from the fan installation manual to finish installingthe fan.
Form # 41475-01 Rev. 1-23-2001 © 2001 Hunter Fan Company2. Press the remote control’s HIGH speed button (refer to Figure 4). Thefan should start and reach it’s maximum speed. If the fan does notstart, or is turning too slow, turn off the power at the wall switch. Pullthe fan’s pull chain to change speed. Reapply power and try Highspeed again. Repeat this procedure until you have confirmed that thefan’s pull chain is set to HIGH speed.Operation:1. Turn ON wall switch, the light will turn ON at maximum brightness.2. Light Operation:• Press and quickly release the light button on the hand held re-mote to turn the light OFF or ON. (Light will come ON at maxi-mum brightness.)• Press and hold the light button for more than 1 second to turnthe light ON and decrease from maximum brightness to OFF.• Release the light button when the desired light level is reached.• Continue to hold the light button to repeat the cycle. (Maxi-mum–light level decrease–OFF)• While the light is ON, holding the light button will decrease thelight brightness.• Turning the light OFF resets the dimming function. The next pressof the light button will start at maximum brightness.3. Fan Operation:• Press the High, Medium, or Low speed buttons to turn the ceil-ing fan ON at the desired speed.• Press the fan OFF key to turn the ceiling fan OFF.For best fan operation: Allow the ceiling fan motor to start on High,then select the desired speed.4. Manual Light Switch Operation:To turn the lights ON without the transmitter, turn OFF the wall switchfor 5 seconds, then turn the wall switch back ON. The light will turnON at maximum brightness, and the fan will be OFF.For everyday operation, leave the wall switch ON. However, if the con-trol will not be used for an extended period of time (5 days or more),turn the wall switch OFF.Testing the Control1. When the installation is complete, restore power at main electricalpanel. Then, turn on the wall switch. The light kit should turn ON. Ifthe light remains OFF, turn off the power at the wall switch. Pull thelight kit’s pull chain to turn the light ON. Turn the wall switch backON.Warning!• Do not use the pull chain to operate the light. Pulling the chain whilepower is applied can damage the receiver. It is recommended to shortenthe pull chain(s) to prevent accidental use.• Do not use the pull chain switch to change speeds. Pulling the chainwhile power is applied can damage the receiver or ceiling fan.Symptom Possible Causes SolutionTroubleshooting1. No functions operate.2. Operates only at close range.3. Inconsistent operation.Main Power not restored.Signal blocked from reaching receiver.Signal partially blocked from reaching receiver.Replace fuse. Turn ON circuit breaker. Turn ON wall switch.Extend antenna into ceiling box, or move it for betterreception.Extend antenna into ceiling box, or move it for betterreception.Fan pull chain not set to High.Light pull chain not set to ON.Receiver wiring incorrect.Transmitter and receiver jumper switches do not match.Battery too weak.Turn OFF power at wall switch or main electric panel. Setfan to High speed.Set light kit to ON.Verify wiring connections.Set transmitter and receiver to same jumper switch set-ting.Replace with new, alkaline battery.Battery too weak. Replace with new, alkaline battery.RF interference. Turn OFF wall switch for 5 seconds, then turn back ON.Continuing RF interference. Change dip switch settings to a different code in bothTransmitter and Receiver.Transmitter Installation:1. Install a 12 volt alkaline battery inside the hand-held transmitter aftersetting the jumper switches to match the jumper switches in the re-ceiver.2. Mount the remote holder over the ceiling fan’s wall switch using theexisting wall plate screws. Refer to Figure 4.3. The transmitter can be placed on the remote holder for convenienceor safekeeping.Select your own unique code, being sure settings match in the trans-mitter and receiver.Fan HighFan MediumFan LowFan OFFLight Key RemoteHolderFigure 4 - Remote Holder Assembly

Navigation menu