Husqvarna 2754 Gls Users Manual OM, GLS, 96043004700, 2008 01, Ride Mower

2754 GLS HUSO2008_USen_O0802014_

2754 GLS to the manual 61789a60-3451-7854-f5d0-ffc0ba9d1eae

2015-01-24

: Husqvarna Husqvarna-2754-Gls-Users-Manual-317437 husqvarna-2754-gls-users-manual-317437 husqvarna pdf

Open the PDF directly: View PDF .
Page Count: 48

Download
Open PDF In Browser	View PDF

Operator's
Manual

2008-01
O0802014

Ride Mower

2754 GLS
96043004700

03002

Operator's Manual

SAFETY RULES
Safe Operation Practices for Ride-On Mowers
DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE
TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

•
WARNING: In order to prevent accidental starting when setting up,
transporting, adjusting or making
repairs, always disconnect spark plug
wire and place wire where it cannot
contact spark plug.

•
•
•

WARNING: Do not coast down a hill
in neutral, you may lose control of
the tractor.

•
•

WARNING: Tow only the attachments
that are recommended by and comply
with specifications of the manufacturer
of your tractor. Use common sense
when towing. Operate only at the lowest possible speed when on a slope.
Too heavy of a load, while on a slope,
is dangerous. Tires can lose traction
with the ground and cause you to lose
control of your tractor.

•
•
•
•

WARNING

•

Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals
known to the State of California to cause cancer and
birth defects or other reproductive harm.

•

WARNING

II. SLOPE OPERATION

Battery posts, terminals and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands
after handling.

I. GENERAL OPERATION
•
•
•
•
•
•
•
•

Read, understand, and follow all instructions on the
machine and in the manual before starting.
Do not put hands or feet near rotating parts or under
the machine. Keep clear of the discharge opening at
all times.
Only allow responsible adults, who are familiar with
the instructions, to operate the machine.
Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blades.
Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.
Never direct discharged material toward anyone. Avoid
discharging material against a wall or obstruction.
Material may ricochet back toward the operator. Stop
the blades when crossing gravel surfaces.

Do not operate machine without the entire grass catcher,
discharge guard, or other safety devices in place and
working.
Slow down before turning.
Never leave a running machine unattended. Always
turn off blades, set parking brake, stop engine, and
remove keys before dismounting.
Disengage blades when not mowing. Shut off engine
and wait for all parts to come to a complete stop before
cleaning the machine, removing the grass catcher, or
unclogging the discharge guard.
Operate machine only in daylight or good artificial
light.
Do not operate the machine while under the influence
of alcohol or drugs.
Watch for traffic when operating near or crossing
roadways.
Use extra care when loading or unloading the machine
into a trailer or truck.
Always wear eye protection when operating machine.
Data indicates that operators, age 60 years and above,
are involved in a large percentage of riding mower-related injuries. These operators should evaluate their
ability to operate the riding mower safely enough to
protect themselves and others from serious injury.
Follow the manufacturer's recommendation for wheel
weights or counterweights.
Keep machine free of grass , leaves or other debris
build-up which can touch hot exhaust / engine parts
and burn. Do not allow the mower deck to plow leaves
or other debris which can cause build-up to occur.
Clean any oil or fuel spillage before operating or
storing the machine. Allow machine to cool before
storage.

Slopes are a major factor related to loss of control and
tip-over accidents, which can result in severe injury or
death. Operation on all slopes requires extra caution. If
you cannot back up the slope or if you feel uneasy on it,
do not mow it.
• Mow up and down slopes, not across.
• Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could overturn the machine.
Tall grass can hide obstacles.
• Choose a low ground speed so that you will not have
to stop or shift while on the slope.
• Do not mow on wet grass. Tires may lose traction.
Always keep the machine in gear when going down
slopes. Do not shift to neutral and coast downhill.
• Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope.
• Keep all movement on the slopes slow and gradual.
Do not make sudden changes in speed or direction,
which could cause the machine to roll over.
• Use extra care while operating machine with grass
catchers or other attachments; they can affect the
stability of the machine. Do no use on steep slopes.
• Do not try to stabilize the machine by putting your foot
on the ground.
• Do not mow near drop-offs, ditches, or embankments.
The machine could suddenly roll over if a wheel is over
the edge or if the edge caves in.

SAFETY RULES
Safe Operation Practices for Ride-On Mowers
GENERAL SERVICE
• Never operate machine in a closed area.
• Keep all nuts and bolts tight to be sure the equipment
is in safe working condition.
• Never tamper with safety devices. Check their proper
operation regularly.
• Keep machine free of grass, leaves, or other debris
build-up. Clean oil or fuel spillage and remove any
fuel-soaked debris. Allow machine to cool before
storing.
• If you strike a foreign object, stop and inspect the
machine. Repair, if necessary, before restarting.
• Never make any adjustments or repairs with the engine
running.
• Check grass catcher components and the discharge
guard frequently and replace with manufacturer's recommended parts, when necessary.
• Mower blades are sharp. Wrap the blade or wear
gloves, and use extra caution when servicing them.
• Check brake operation frequently. Adjust and service
as required.
• Maintain or replace safety and instruction labels, as
necessary.

III. CHILDREN
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume that
children will remain where you last saw them.
• Keep children out of the mowing area and in the watchful
care of a responsible adult other than the operator.
• Be alert and turn machine off if a child enters the
area.
• Before and while backing, look behind and down for
small children.
• Never carry children, even with the blades shut off. They
may fall off and be seriously injured or interfere with
safe machine operation. Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
• Never allow children to operate the machine.
• Use extra care when approaching blind corners, shrubs,
trees, or other objects that may block your view of a
child.

IV. TOWING
•
•
•
•
•

Tow only with a machine that has a hitch designed for
towing. Do not attach towed equipment except at the
hitch point.
Follow the manufacturer's recommendation for weight
limits for towed equipment and towing on slopes.
Never allow children or others in or on towed equipment.
On slopes, the weight of the towed equipment may
cause loss of traction and loss of control.
Travel slowly and allow extra distance to stop.

•
•
•

V. SERVICE
SAFE HANDLING OF GASOLINE
To avoid personal injury or property damage, use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive.
• Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
• Use only approved gasoline container.
• Never remove gas cap or add fuel with the engine
running. Allow engine to cool before refueling.
• Never fuel the machine indoors.
• Never store the machine or fuel container where there
is an open flame, spark, or pilot light such as on a water
heater or other appliances.
• Never fill containers inside a vehicle or on a truck or
trailer bed with plastic liner. Always place containers
on the ground away from your vehicle when filling.
• Remove gas-powered equipment from the truck or
trailer and refuel it on the ground. If this is not possible,
then refuel such equipment with a portable container,
rather than from a gasoline dispenser nozzle.
• Keep the nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete.
Do not use a nozzle lock-open device.
• If fuel is spilled on clothing, change clothing immediately.
• Never overfill fuel tank. Replace gas cap and tighten
securely.

•

•
•
•
•
•
•
•
•

Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.
Never carry children, even with the blades shut off. They
may fall off and be seriously injured or interfere with
safe machine operation. Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
Keep children out of the mowing area and in the watchful
care of a responsible adult other than the operator.
Be alert and turn machine off if a child enters the
area.
Before and while backing, look behind and down for
small children.
Mow up and down slopes (15° Max), not across.
Choose a low ground speed so that you will not have
to stop or shift while on the slope.
Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope.
If machine stops while going uphill, disengage blades,
shift into reverse and back down slowly.
Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.

PRODUCT SPECIFICATIONS
Gasoline Capacity
and type:

4 Gallons
Unleaded Regular

Oil Type (API-SG-SL):

SAE 30 (above 32°F)
SAE 5W-30 (below 32°F)

Oil Capacity:

W/ Filter:
W/O Filter:

Spark Plug:

Champion QC12YC
(Gap: .040")

Ground Speed (MPH):

Forward:
Reverse:

Charging System:

16 AMPS @ 3600 RPM

Battery:
Case Size:

AMP/HR:
MIN. CCA:
U1R

Blade Bolt Torque:

45-55 FT. LBS.

CUSTOMER RESPONSIBILITIES
•
•
•

64 oz.
60 oz.

Read and observe the safety rules.
Follow a regular schedule in maintaining, caring for
and using your tractor.
Follow the instructions under “Maintenance” and “Storage” sections of this owner’s manual.

WARNING: This tractor is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered
land unless the engine’s exhaust system is equipped with
a spark arrester meeting applicable local or state laws (if
any). If a spark arrester is used, it should be maintained
in effective working order by the operator.
In the state of California the above is required by law
(Section 4442 of the California Public Resources Code).
Other states may have similar laws. Federal laws apply
on federal lands.
A spark arrester for the muffler is available through your
nearest authorized service center/department (See REPAIR
PARTS section of this manual).

0 – 5.8
0 – 2.1
28
230

CONGRATULATIONS on your purchase of a new tractor.
It has been designed, engineered and manufactured to give
you the best possible dependability and performance.
Should you experience any problem you cannot easily remedy, please contact your nearest authorized servicecenter/
department We have competent, well-trained technicians
and the proper tools to service or repair this tractor.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your tractor properly.
Always observe the “SAFETY RULES”.

TABLE OF CONTENTS
MAINTENANCE ..................................................... 17-20
SERVICE AND ADJUSTMENTS ............................ 21-25
STORAGE .................................................................... 26
TROUBLESHOOTING ............................................ 27-28
REPAIR PARTS ...................................................... 29-44
WARRANTY............................................. BACK COVER

SAFETY RULES ......................................................... 2-3
PRODUCT SPECIFICATIONS ....................................... 4
CUSTOMER RESPONSIBILITIES................................. 4
ASSEMBLY ................................................................. 6-9
OPERATION ........................................................... 10-16
MAINTENANCE SCHEDULE ...................................... 17

UNASSEMBLED PARTS
Mower

(5) Large Retainer
Springs - 7/16

Mower Front Wheel

(1) 3/4 O.D. Washers
(1) Wheel
(1) 1-1/4 O.D. Washer

(2) Smaller Retainer
Springs - 5/16

(5) 1-3/16 O.D. Washers

(1) Shoulder Bolt

(1) Locknut
3/8-16

(1) Anti-Sway Bar

Slope Sheet
(1) Oil Drain Tube
For Future Use

Keys
(1) Front Link
Assembly

(2) Rear Lift Link
Assemblies

(2) Keys

ASSEMBLY
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.

TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
(1) 3/4" wrench
(1) Utility knife
(1) 9/16" wrench
(1) Pliers
(1) Tire Pressure Gauge
When right or left hand is mentioned in this manual, it means
from your point of view, when you are in the operating
position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM
CARTON
FIG. 2

UNPACK CARTON
•
•
•
•

Remove all accessible loose parts and parts cartons
from carton .
Cut along dashed lines on all four panels of carton.
Remove end panels and lay side panels flat.
Remove mower and packing materials.
Check for any additional loose parts or cartons and
remove.

NOTE: You may now roll or drive your tractor off the skid.
Follow the appropriate instruction below to remove the
tractor from the skid.
WARNING: Before starting, read, understand and follow
all instructions in the Operation section of this manual. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other people and objects.

TO ROLL TRACTOR OFF SKID (See Operation section for location and function of
controls)

CHECK BATTERY (See Fig. 1)
• Lift hood to raised position.
NOTE: If this battery is put into service after month and year
indicated on label (L) (label is located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in Maintenance section of this manual
for charging instructions).

•
•
•
•

Raise attachment lift lever to its highest position.
Release parking brake by depressing brake pedal.
Place freewheel control in disengaged position to disengage transmission (See “TO TRANSPORT” in the
Operation section of this manual).
Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See Operation section for location and function of
controls)
•
L

02931

FIG. 1

ADJUST SEAT (See Fig. 2)
•
•
•

Sit in seat.
Lift up adjustment lever (A) and slide seat until a comfortable position is reached which allows you to press
clutch/brake pedal all the way down.
Release lever to lock seat in position.

Be sure all the above assembly steps have been completed.
• Check engine oil level and fill fuel tank with gasoline.
• Place freewheel control in "transmission engaged"
position (see "TO TRANSPORT" in Operation section
of this manual).
• Sit on seat in operating position, depress clutch/brake
pedal and set the parking brake.
• Place motion control lever in neutral (N) position.
• Press lift lever plunger and raise attachment lift lever
to its highest position.
• Remove key from bag and start the engine (see "TO
START ENGINE" in the Operation section of this
manual). After engine has started, move throttle control
to idle (slow) position.
• Release parking brake.
• Slowly move the motion control lever forward and slowly
drive tractor off skid.
• Apply brake to stop tractor, set parking brake and place
motion control lever in neutral position.
• Turn ignition key to "STOP" position.
Continue with the instructions that follow.

ASSEMBLY
ASSEMBLE FRONT WHEEL TO
MOWER (See Fig. 3)
Using shoulder bolt, washer and locknut from parts
bag, assemble front wheel to mower as shown. Tighten
securely.

02
05
1

•

A
FIG. 5
NOTE: Be sure mower side suspension arms (A) are pointing forward before sliding mower under tractor.
• Slide mower under tractor until it is centered under
tractor.
• FIRST INSTALL ANTI-SWAY BAR (S).
- From right side of mower, insert anti-sway bar into
hole in transmission bracket (T).

FIG. 3

INSTALL MOWER AND DRIVE BELT

(See Figs. 4-12)
See MOWER AND DRIVE BELT ASSEMBLY Supplement
Sheet for additional guidance on this assembly.
Be sure tractor is on level surface and engage parking
brake.
• Lower attachment lift lever to it's lowest position.

CAUTION: Lift lever is spring loaded. Have
a tight grip on lift lever, lower it slowly and
engage in lowest position.
•

Turn steering wheel to the left as far as it will go and
position mower on right side of tractor with deflector
shield to the right.

A
02995

FIG. 6
- Pivot bar towards you and insert other end of bar
into hole in rear mower bracket (D). Move mower
as needed to insert bar.
- Secure with washer and retainer spring as shown
using small 5/16 retainer spring.

D
02965

FIG. 4
•

Remove plastic tie securing belt, bring belt forward
and check belt for proper routing in all mower pulley
grooves.
02996

FIG. 7

ASSEMBLY
•

•

ATTACH MOWER SIDE SUSPENSION ARMS (A) TO
CHASSIS - Position hole in arm over pin (B) on outside
of tractor chassis and secure with washer and retainer
spring.
Repeat on opposite side of tractor.

•
•

•

Turn steering wheel to position wheels straight forward.
ATTACH FRONT LINK (E) - Work from left side of
tractor. Insert rod end of link assembly through front
hole in tractor front suspension bracket (F) and secure
with7/16 retainer spring (G) through hole in link located
behind the bracket.
Insert other end of link (E) into hole in front mower
bracket (H) and secure with washer and 5/16 retainer
spring (J).

•

FIG. 8
ATTACH REAR LIFT LINKS (C) - Insert rod end of lift
link assembly into hole in tractor lift shaft suspension
arm (L) and pivot link down to mower. Lift rear corner
of mower and position slot in link assembly over pin on
rear mower bracket (D) and secure with washer and
retainer spring.
Repeat on opposite side of tractor.

FIG. 10
•

Disengage belt tension rod (K) from locking bracket
(L).
• Install belt onto engine clutch pulley (M).
IMPORTANT: Check belt for proper routing in all mower
pulley grooves.

L
C

FIG. 9
L

B
M

K
F

E
H

FIG. 11

ASSEMBLY
✓CHECKLIST

BEFORE YOU OPERATE YOUR NEW TRACTOR, WE
WISH TO ASSURE THAT YOU RECEIVE THE BEST
PERFORMANCE AND SATISFACTION FROM THIS
QUALITY PRODUCT.
PLEASE REVIEW THE FOLLOWING CHECKLIST:
✓ All assembly instructions have been completed.
✓ No remaining loose parts in carton.
✓ Battery is properly prepared and charged.
✓ Seat is adjusted comfortably and tightened securely.
✓ All tires are properly inflated. (For shipping purposes,
the tires were overinflated at the factory).
✓ Be sure mower deck is properly leveled side-to-side/
front-to-rear for best cutting results. (Tires must be
properly inflated for leveling).
✓ Check mower and drive belts. Be sure they are routed
properly around pulleys and inside all belt keepers.
✓ Check wiring. See that all connections are still secure
and wires are properly clamped.
✓ Before driving tractor, be sure freewheel control is in
“transmission engaged” position (see “TO TRANSPORT” in the Operation section of this manual).
WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT
ITEMS:
✓ Engine oil is at proper level.
✓ Fuel tank is filled with fresh, clean, regular unleaded
gasoline.
✓ Become familiar with all controls, their location and
function. Operate them before you start the engine.
✓ Be sure brake system is in safe operating condition.
✓ Be sure Operator Presence System and Reverse Operation System (ROS) are working properly (See the
Operation and Maintenance sections in this manual).
✓ It is important to purge the transmission before operating your tractor for the first time. Follow proper
starting and transmission purging instructions (See
“TO START ENGINE” and “PURGE TRANSMISSION”
in the Operation section of this manual).

FIG. 12
•

Engage belt tension rod (K) on locking bracket (L).
CAUTION: Belt tension rod is spring
loaded. Have a tight grip on rod and engage slowly.

•
•

Raise attachment lift lever to highest position.
If necessary, adjust gauge wheels before operating
mower as shown in the Operation section of this
manual.

CHECK TIRE PRESSURE
The tires on your tractor were overinflated at the factory
for shipping purposes. Correct tire pressure is important
for best cutting performance.
• Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS
For best cutting results, mower housing should be properly leveled. See “TO LEVEL MOWER HOUSING” in the
Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL
BELTS
See the figures that are shown for replacing motion and
mower blade drive belts in the Service and Adjustments
section of this manual. Verify that the belts are routed
correctly.

CHECK BRAKE SYSTEM
After you learn how to operate your tractor, check to see that
the brake is operating properly. See “TO CHECK BRAKE”
in the Service and Adjustments section of this manual.

OPERATION
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.

REVERSE

ENGINE OFF

LIGHTS ON

NEUTRAL

REVERSE
OPERATION
SYSTEM (ROS)

FUEL

HIGH

LOW

ENGINE ON

BATTERY

CHOKE

ENGINE START

REVERSE

FAST

IGNITION SWITCH

PARKING BRAKE

FORWARD

SLOW

MOWER HEIGHT

MOWER LIFT

CLUTCH/BRAKE
PEDAL

CRUISE CONTROL
15

ATTACHMENT
CLUTCH DISENGAGED

ATTACHMENT
CLUTCH ENGAGED

DANGER, KEEP HANDS
AND FEET AWAY

SLOPE HAZARDS
KEEP AREA CLEAR
(SEE SAFETY RULES SECTION)

DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.

FREE WHEEL
(Automatic Models only)

WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
might result in minor or moderate injury.
CAUTION when used without the alert symbol,
indicates a situation that could result in damage
to the tractor and/or engine.

Failure to follow instructions
could result in serious injury or
death. The safety alert symbol
is used to identify safety information about hazards which can
result in death, serious injury
and/or property damage.

HOT SURFACES indicates a hazard which,
if not avoided, could result in death, serious injury
and/or property damage.
FIRE indicates a hazard which, if not avoided,
could result in death, serious injury and/or
property damage.

OPERATION
KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.
Save this manual for future reference.

P
H

E
G

FIG. 13
Our tractors conform to the applicable safety standards of the American National Standards Institute.
(G) REVERSE OPERATION SYSTEM (ROS) "ON" POSITION – Allows operation of mower or other powered
attachment while in reverse.
(H) LIGHT SWITCH – Turns the headlights on and off.
(J) MOTION CONTROL LEVER - Selects the speed and
direction of the tractor.
(M) FREEWHEEL CONTROL – Disengages transmission
for pushing or slowly towing the tractor with the engine
off.
(N) CHOKE CONTROL – Used when starting a cold
engine.
(P) SERVICE REMINDER / HOUR METER – Indicates when
service is required for the engine and mower.
(Q) 12-VOLT POWER PORT – Used for 12-volt accessories.

(A) ATTACHMENT LIFT LEVER – Used to raise and lower
the mower or other attachments mounted to your tractor.
(B) CLUTCH/BRAKE PEDAL – Used for declutching and
braking the tractor and starting the engine.
(C) PARKING BRAKE – Locks clutch/brake pedal into the
brake position.
(D) THROTTLE CONTROL – Used to control engine
speed.
(E) ATTACHMENT CLUTCH SWITCH – Used to engage
the mower blades, or other attachments mounted to your
tractor.
(F) IGNITION SWITCH – Used for starting and stopping
the engine.

OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, which can result
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor
or performing any adjustments or repairs. We recommend standard safety glasses or a wide
vision safety mask worn over spectacles.
IMPORTANT: Leaving the ignition switch in any position
other than "STOP" will cause the battery to discharge and
go dead.
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may
cause “browning” of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE(See Fig. 14)
Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine.
• Depress brake pedal (B) all the way down and hold.
• Pull parking brake lever (C) up and hold, release pressure from brake pedal (B), then release parking brake
lever. Pedal should remain in brake position. Make
sure parking brake will hold tractor secure.

CAUTION: Always stop tractor completely, as described above, and set
parking brake before leav ing the
operator's position.

D
B
C

FIG. 14

F
N

STOPPING
MOWER BLADES • To stop mower blades, push attachment clutch switch
in to disengaged position (o).

FIG. 16

TO USE THROTTLE CONTROL - D (See Fig.
16)
Always operate engine at full speed (fast).
• Operating engine at less than full speed (fast) reduces
engines operating efficiency.
• Full speed (fast) offers the best bagging and mower
performance.
(I) ATTACHMENT
CLUTCH SWITCH
PULL OUT TO “ENGAGE”

(O) PUSH-IN TO
“DISENGAGED”

TO USE CHOKE CONTROL - N (See Fig. 16)
Use choke control whenever you are starting a cold engine.
Do not use to start a warm engine.
• To engage choke control, pull knob out. Slowly push
knob in to disengage.

FIG. 15
GROUND DRIVE • To stop ground drive, depress clutch/brake pedal all
the way down.
• Move motion control lever (J) to neutral position.

TO MOVE FORWARD AND BACKWARD
(See Fig. 17)
The direction and speed of movement is controlled by the
motion control lever. (J)

ENGINE • Move throttle control (D) between half and full speed
(fast) position.
NOTE: Failure to move throttle control between half and
full speed (fast) position, before stopping, may cause engine to “backfire”.
• Turn ignition key (F) to “STOP” position and remove
key. Always remove key when leaving tractor to prevent
unauthorized use.
• Never use choke (N) to stop engine.

OPERATION
NOTE: Adjust gauge wheels with tractor on a flat level
surface.
• Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in this section of
manual).
• With mower in desired height of cut position, gauge
wheels should be assembled so they are slightly off
the ground. Install gauge wheel in appropriate hole.
Tighten securely.
• Repeat for all, installing gauge wheel in same adjustment hole.

FIG. 17
•
•
•

Start tractor with motion control lever in neutral (N)
position.
Release parking brake.
Slowly move motion control lever to desired position.

TO ADJUST MOWER CUTTING HEIGHT
(See Fig. 18)

FIG. 19

The position of the attachment lift lever (A) determines the
cutting height.

TO OPERATE MOWER
Your tractor is equipped with an operator presence sensing
switch. Any attempt by the operator to leave the seat with
the engine running and the attachment clutch engaged will
shut off the engine. You must remain fully and centrally
positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough,
rolling terrain or hills.
1. Select desired height of cut with attachment lift lever.
2. Start mower blades by engaging attachment clutch
control.

TO STOP MOWER BLADES disengage attachment clutch control.

FIG. 18
• Put attachment lift lever in desired cutting height slot.
The cutting height range is approximately 1" to 4". The
heights are measured from the ground to the blade tip with
the engine not running. These heights are approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
• The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
• For best cutting performance, grass over 6 inches
in height should be mowed twice. Make the first cut
relatively high; the second to desired height.

CAUTION: Do not operate the mower
without either the entire grass catcher,
on mowers so equipped, or the deflector shield (S) in place.

FIG. 20

TO ADJUST GAUGE WHEELS (See Fig. 19)

REVERSE OPERATION SYSTEM (ROS)

Gauge wheels are properly adjusted when they are slightly
off the ground when mower is at the desired cutting height
in operating position. Gauge wheels then keep the deck
in proper position to help prevent scalping in most terrain
conditions.

Your tractor is equipped with a Reverse Operation System
(ROS). Any attempt by the operator to travel in the reverse
direction with the attachment clutch engaged will shut off
the engine unless ignition key is placed in the ROS "ON"
position.

OPERATION
•

WARNING: Backing up with the attachment clutch engaged while mowing is strongly discouraged. Turning the
ROS "ON", to allow reverse operation with the attachment
clutch engaged, should only be done when the operator
decides it is necessary to reposition the machine with the
attachment engaged. Do not mow in reverse unless
absolutely necessary.

•

Transmission Engaged

USING THE REVERSE OPERATION SYSTEM Only use if you are certain no children or other bystanders
will enter the mowing area.
• Move motion control lever to neutral (N) position.
• With engine running, turn ignition key counterclockwise
to ROS "ON" position.
• Look down and behind before and while backing.
• Slowly move motion control lever to reverse (R) position
to start movement.
• When use of the ROS is no longer needed, turn the
ignition key clockwise to engine "ON" position.
ROS "ON" POSITION

Do not push or tow tractor at more than two (2)
MPH.
To reengage transmission, reverse above procedure.

Transmission Disengaged

FIG. 21
NOTE: To protect hood from damage when transporting
your tractor on a truck or a trailer, be sure hood is closed
and secured to tractor. Use an appropriate means of tying
hood to tractor (rope, cord, etc.).

ENGINE "ON" POSITION
(NORMAL OPERATING)

SERVICE REMINDER/HOUR METER
Service reminder shows the total number of hours the engine
has run and flashes to indicate that the engine or mower
needs servicing. When service is required, the service
reminder will flash for two hours. To service engine and
mower, see the Maintenance section of this manual.
NOTE: Service reminder runs when the ignition key is in
any position but "STOP". For accurate reading, be sure
key remains in the "STOP" position when engine is not
running.

02828

TO OPERATE ON HILLS
CAUTION: Do not drive up or down
hills with slopes greater than 15° and
do not drive across any slope.
•
•
•
•
•

TOWING CARTS AND OTHER ATTACHMENTS
Tow only the attachments that are recommended by and
comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load,
while on a slope, is dangerous. Tires can lose traction with
the ground and cause you to lose control of your tractor.

Choose the slowest speed before starting up or down
hills.
Avoid stopping or changing speed on hills.
If slowing is necessary, move throttle control lever to
slower position.
If stopping is absolutely necessary, push clutch/brake
pedal quickly to brake position and engage parking
brake.
Move motion control lever to neutral (N) position.

BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL
The engine in your tractor has been shipped, from the
factory, already filled with summer weight oil.
• Check engine oil with tractor on level ground.
• Remove oil fill cap/dipstick and wipe clean, reinsert the
dipstick and screw cap tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
• For cold weather operation you should change oil for
easier starting (See “OIL VISCOSITY CHART” in the
Maintenance section of this manual).
• To change engine oil, see the Maintenance section in
this manual.

IMPORTANT:
THE MOTION CONTROL LEVER DOES NOT
RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/
BRAKE PEDAL IS DEPRESSED.

•
•
•

To restart movement, slowly release parking brake and
clutch/brake pedal.
Slowly move motion control lever to slowest setting.
Make all turns slowly.

TO TRANSPORT (See Figs. 13 and 21)
When pushing or towing your tractor, be sure to disengage
transmission by placing freewheel control in freewheeling
position. Free wheel control is located at the rear drawbar
of tractor.
• Raise attachment lift to highest position with attachment
lift control.
• Pull freewheel control out and down into the slot and
release so it is held in the disengaged position.

OPERATION
•

ADD GASOLINE
•

Fill fuel tank to bottom of filler neck. Do not overfill. Use
fresh, clean, regular unleaded gasoline with a minimum of
87 octane. (Use of leaded gasoline will increase carbon
and lead oxide deposits and reduce valve life). Do not
mix oil with gasoline. Purchase fuel in quantities that can
be used within 30 days to assure fuel freshness.

The attachments and ground drive can now be used. If
the engine does not accept the load, restart the engine
and allow it to warm up for one minute using the choke
as described above.

COLD WEATHER STARTING (50° F and below)
• When engine starts, slowly push choke control in until
the engine begins to run smoothly. Continue to push
the choke control in small steps allowing the engine to
accept small changes in speed and load, until the choke
control is fully in. If the engine starts to run roughly, pull
the choke control out slightly for a few seconds and
then continue to push the control in slowly. This may
require an engine warm-up period from several seconds
to several minutes, depending on the temperature.

CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
IMPORTANT: WHEN OPERATING IN TEMPERATURES
BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE
GASOLINE TO HELP INSURE GOOD COLD WEATHER
STARTING.

AUTOMATIC TRANSMISSION WARM UP
• Before driving the unit in cold weather, the transmission
should be warmed up as follows:
• Be sure the tractor is on level ground.
• Place the motion control lever in neutral.
Release the parking brake and let the clutch/brake
slowly return to operating position.
• Allow one minute for transmission to warm up. This
can be done during the engine warm up period.
• The attachments can be used during the engine warm-up
period after the transmission has been warmed up and
may require the choke control be pulled out slightly.
NOTE: If at a high altitude (above 3000 feet) or in cold
temperatures (below 32 F) the carburetor fuel mixture may
need to be adjusted for best engine performance. See “TO
ADJUST CARBURETOR” in the Service and Adjustments
section of this manual.

CAUTION: Alcohol blended fuels (called gasohol
or using ethanol or methanol) can attract moisture
which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel
system of an engine while in storage. To avoid engine
problems, the fuel system should be emptied before
storage of 30 days or longer. Drain the gas tank,
start the engine and let it run until the fuel lines and
carburetor are empty. Use fresh fuel next season.
See Storage Instructions for additional information.
Never use engine or carburetor cleaner products in
the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 13)
When starting the engine for the first time or if the engine
has run out of fuel, it will take extra cranking time to move
fuel from the tank to the engine.
• Be sure freewheel control is in the transmission engaged position.
• Sit on seat in operating position, depress clutch/brake
pedal and set parking brake.
• Place motion control lever in neutral (N) position.
• Move attachment clutch to “DISENGAGED” position.
• Move throttle control to fast position
• Pull choke control out for a cold engine start attempt.
For a warm engine start attempt the choke control may
not be needed.
NOTE: Before starting, read the warm and cold starting
procedures below.
• Insert key into ignition and turn key clockwise to
“START” position and release key as soon as engine
starts. Do not run starter continuously for more than
fifteen seconds per minute. If the engine does not start
after several attempts, push choke control in, wait a
few minutes and try again. If engine still does not start,
pull the choke control out and retry.

PURGE TRANSMISSION
CAUTION: Never engage or disengage
freewheel lever while the engine is
running.
To ensure proper operation and performance, it is recommended that the transmission be purged before operating
tractor for the first time. This procedure will remove any
trapped air inside the transmission which may have developed during shipping of your tractor.
IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE
REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD
BE PURGED AFTER REINSTALLATION BEFORE OPERATING
THE TRACTOR.

•
•
•

WARM WEATHER STARTING (50° F and above)
• When engine starts, slowly push choke control in until
the engine begins to run smoothly. If the engine starts
to run roughly, pull the choke control out slightly for a
few seconds and then continue to push the control in
slowly.

Place tractor safely on a level surface - that is clear
and open - with engine off and parking brake set.
Disengage transmission by placing freewheel control
in freewheeling position (See “TO TRANSPORT” in
this section of manual).
Sitting in the tractor seat, start engine. After the engine
is running, move throttle control to slow position. With
motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

OPERATION
MOWING TIPS

CAUTION: At any time, during step 4,
there may be movement of the drive
wheels.

•

Move motion control lever to full forward position and
hold for five (5) seconds. Move lever to full reverse
position and hold for five (5) seconds. Repeat this
procedure three (3) times.
• Move motion control lever to neutral (N) position. Shutoff engine and set parking brake.
• Engage transmission by placing freewheel control in
engaged position (See “TO TRANSPORT” in this section of manual).
• Sitting in the tractor seat, start engine. After the engine
is running, move throttle control to half (1/2) speed.
With motion control lever in neutral (N) position, slowly
disengage clutch/brake pedal.
• Slowly move motion control lever forward, after the
tractor moves approximately five (5) feet, slowly move
motion control lever to reverse position. After the tractor moves approximately five (5) feet return the motion control lever to the neutral (N) position. Repeat
this procedure with the motion control lever three (3)
times.
Your transmission is now purged and now ready for normal
operation.

•
•

•

Mower should be properly leveled for best mowing
performance. See “TO LEVEL MOWER HOUSING” in
the Service and Adjustments section of this manual.
The left hand side of mower should be used for trimming.
Drive so that clippings are discharged onto the area
that has been cut. Have the cut area to the right of the
machine. This will result in a more even distribution of
clippings and more uniform cutting.
When mowing large areas, start by turning to the right
so that clippings will discharge away from shrubs,
fences, driveways, etc. After one or two rounds, mow
in the opposite direction making left hand turns until
finished (See Fig. 22).

FIG. 22
•

•
•

•

If grass is extremely tall, it should be mowed twice to
reduce load and possible fire hazard from dried clippings. Make first cut relatively high; the second to the
desired height.
Do not mow grass when it is wet. Wet grass will plug
mower and leave undesirable clumps. Allow grass to
dry before mowing.
Always operate engine at full throttle when mowing to assure better mowing performance and proper
discharge of material. Regulate ground speed by
selecting a low enough gear to give the mower cutting
performance as well as the quality of cut desired.
When operating attachments, select a ground speed
that will suit the terrain and give best performance of
the attachment being used.

MAINTENANCE
MAINTENANCE
SCHEDULE

BEFORE
EACH
USE

EVERY
8
HOURS

EVERY
25
HOURS

EVERY
50
HOURS

EVERY
100
HOURS

EVERY
SEASON

BEFORE
STORAGE

Check Brake Operation
Check Tire Pressure

T Check Operator Presence & ROS Systems
R
A Check for Loose Fasteners
C Check/Replace Mower Blades
T Lubrication Chart
0 Check Battery Level
R Clean Battery and Terminals

Check Transaxle Cooling
Check Mower Levelness
Check V-Belts
Check Engine Oil Level
Change Engine Oil (with oil filter)

1,2

Change Engine Oil (without oil filter)

1,2

E Clean Air Filter
N
G Clean Air Screen
I Inspect Muffler/Spark Arrester
N Replace Oil Filter (If equipped)
E Clean Engine Cooling Fins

2
2

maint_sch-tractore.ROS.e

1, 2
2

Replace Spark Plug
Replace Air Filter Paper Cartridge

Replace Fuel Filter
1 - Change more often when operating under a heavy load or
in high ambient temperatures.
2 - Service more often when operating in dirty or dusty conditions.

3 - Replace blades more often when mowing in sandy soil.
4 - Not required if equipped with maintenance-free battery.

LUBRICATION CHART

GENERAL RECOMMENDATIONS

➀ SPINDLE ZERK
➀ FRONT

The warranty on this tractor does not cover items that have
been subjected to operator abuse or negligence. To receive
full value from the warranty, operator must maintain tractor
as instructed in this manual.
Some adjustments will need to be made periodically to
properly maintain your tractor.
At least once a season, check to see if you should make
any of the adjustments described in the Service and
Adjustments section of this manual.
• At least once a year you should replace the spark
plug, clean or replace air filter, and check blades and
belts for wear. A new spark plug and clean air filter
assure proper air-fuel mixture and help your engine
run better and last longer.

WHEEL
BEARING
ZERK

➁ ENGINE
➀ STEERING

SECTOR GEAR
TEETH

➀ MANDREL
ZERKS

01965

BEFORE EACH USE
•
•
•
•
•

➀ General Purpose Grease
➁ Refer to Maintenance “ENGINE” Section

Check engine oil level.
Check brake operation.
Check tire pressure.
Check operator presence and
ROS systems for proper operation.
Check for loose fasteners.

IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS
WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS
LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL
SHORTEN THE LIFE OF THE SELF-LUBRICATING BEARINGS.
IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY,
POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY.

MAINTENANCE
TRACTOR

BLADE CARE

Always observe safety rules when performing any maintenance.

For best results mower blades must be sharp. Replace
worn, bent or damaged blades.

BRAKE OPERATION

CAUTION: Use only a replacement
blade approved by the manufacturer of
your tractor. Using a blade not approved
by the manufacturer of your tractor is
hazardous, could damage your tractor
and void your warranty.

If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be serviced. (See “TO CHECK
BRAKE” in the Service and Adjustments section of this
manual).

TIRES

BLADE REMOVAL (See Fig. 23)

•

Maintain proper air pressure in all tires (See PSI on
tires).
• Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
NOTE: To seal tire punctures and prevent flat tires due
to slow leaks, tire sealant may be purchased from your
local parts dealer. Tire sealant also prevents tire dry rot
and corrosion.

•

Raise mower to highest position to allow access to
blades.
NOTE: Protect your hands with gloves and/or wrap blade
with heavy cloth.
• Remove blade bolt by turning counterclockwise.
• Install new blade with stamped "GRASS SIDE" facing
the ground.
IMPORTANT: To ensure proper assembly, center hole in
blade must align with star on mandrel assembly.
• Install and tighten blade bolt securely (45-55 Ft. Lbs.
torque).
IMPORTANT: Special blade bolt is heat treated.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS)
Be sure operator presence and reverse operation systems
are working properly. If your tractor does not function as
described, repair the problem immediately.
• The engine should not start unless the brake pedal is
fully depressed, and the attachment clutch control is
in the disengaged position.

BLADE
BLADE BOLT
(SPECIAL)

CHECK OPERATOR PRESENCE SYSTEM
• When the engine is running, any attempt by the operator
to leave the seat without first setting the parking brake
should shut off the engine.
• When the engine is running and the attachment clutch
is engaged, any attempt by the operator to leave the
seat should shut off the engine.
• The attachment clutch should never operate unless
the operator is in the seat.
ROS "ON" Position

STAR
CENTER
HOLE

MANDREL
ASSEMBLY

FIG. 23

BATTERY
Your tractor has a battery charging system which is sufficient
for normal use. However, periodic charging of the battery
with an automotive charger will extend its life.
• Keep battery and terminals clean.
• Keep battery bolts tight.
• Keep small vent holes open.
• Recharge at 6-10 amperes for 1 hour.
NOTE: The original equipment battery on your tractor is
maintenance free. Do not attempt to open or remove caps
or covers. Adding or checking level of electrolyte is not
necessary.

Engine "ON" Position
(Normal Operating)

02828

CHECK REVERSE OPERATION (ROS) SYSTEM
• When the engine is running with the ignition switch in
the engine "ON" position and the attachment clutch
engaged, any attempt by the operator to shift into
reverse should shut off the engine.
• When the engine is running with the ignition switch in
the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse
should NOT shut off the engine.

TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals can cause
the battery to “leak” power.
• Remove terminal guard.
• Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.
• Rinse the battery with plain water and dry.
• Clean terminals and battery cable ends with wire brush
until bright.

MAINTENANCE
•
•

Coat terminals with grease or petroleum jelly.
Reinstall battery (See “REPLACING BATTERY" in
the SERVICE AND ADJUSTMENTS section of this
manual).

TO CHANGE ENGINE OIL (See Figs. 24 and 25)
Determine temperature range expected before oil change.
All oil must meet API service classification SG-SL.
• Be sure tractor is on level surface.
• Oil will drain more freely when warm.
• Catch oil in a suitable container.
• Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine when changing oil.
• Remove yellow cap from end of drain valve and install
the drain tube onto the fitting.

V-BELTS
Check V-belts for deterioration and wear after 100 hours
of operation and replace if necessary. The belts are not
adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE COOLING
The transmission fan and cooling fins should be kept clean
to assure proper cooling.
Do not attempt to clean fan or transmission while engine
is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or
steam to clean transaxle.
• Inspect cooling fan to be sure fan blades are intact and
clean.
• Inspect cooling fins for dirt, grass clippings and other
materials. To prevent damage to seals, do not use
compressed air or high pressure sprayer to clean
cooling fins.

OIL DRAIN VALVE

CLOSED AND
LOCKED
POSITION

YELLOW
CAP

The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should
the transaxle ever leak or require servicing, contact your
nearest authorized service center/department.

•
•
•

ENGINE
LUBRICATION

•

Only use high quality detergent oil rated with API service
classification SG-SL. Select the oil’s SAE viscosity grade
according to your expected operating temperature.

•

SAE VISCOSITY GRADES

•

SAE 30
5W-30
-20

-30

0
-20

30
-10

100

60
10

DRAIN
TUBE

FIG. 25

TRANSAXLE PUMP FLUID

Unlock drain valve by pushing inward and turning
counterclockwise.
To open, pull out on the drain valve.
After oil has drained completely, close and lock the
drain valve by pushing inward and turning clockwise
until the pin is in the locked position as shown.
Remove the drain tube and replace the cap onto to the
bottom fitting of the drain valve.
Refill engine with oil through oil fill dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCT SPECIFICATIONS” section of this manual.
Use gauge on oil fill cap/dipstick for checking level.
Be sure dipstick cap is tightened securely for accurate
reading. Keep oil at “FULL” line on dipstick. Tighten
cap onto the tube securely when finished.

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

CLEAN AIR SCREEN

oil_visc_chart1_e

FIG. 24

Air screen must be kept free of dirt and chaff to prevent
engine damage from overheating. Clean with a wire brush
or compressed air to remove dirt and stubborn dried gum
fibers.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, they will result in increased
oil consumption when used above 32°F. Check your engine
oil level more frequently to avoid possible engine damage
from running low on oil.
Change the oil after every 50 hours of operation or at least
once a year if the tractor is not used for 50 hours in one
year.
Check the crankcase oil level before starting the engine
and after each eight (8) hours of operation. Tighten oil fill
cap/dipstick securely each time you check the oil level.

AIR FILTER
Your engine will not run properly using a dirty air filter.
Service air cleaner more often under dusty conditions.
See Engine Manual.

ENGINE OIL FILTER
Replace the engine oil filter every season or every other
oil change if the tractor is used more than 100 hours in
one year.

MAINTENANCE
MUFFLER
Inspect and replace corroded muffler and spark arrester
(if equipped) as it could create a fire hazard and/or damage.

Hose
Nozzle Adapter
Washout Port

SPARK PLUGS
Replace spark plugs at the beginning of each mowing
season or after every 100 hours of operation, whichever
occurs first. Spark plug type and gap setting are shown in
“PRODUCT SPECIFICATIONS” section of this manual.

IN-LINE FUEL FILTER (See Fig. 26)
The fuel filter should be replaced once each season. If fuel
filter becomes clogged, obstructing fuel flow to carburetor,
replacement is required.
• With engine cool, remove filter and plug fuel line sections.
• Place new fuel filter in position in fuel line with arrow
pointing towards carburetor.
• Be sure there are no fuel line leaks and clamps are
properly positioned.
• Immediately wipe up any spilled gasoline.

Fig. 27
IMPORTANT: Tug hose ensuring connection is secure.
5. Turn the water on.
6. While sitting in the operator’s position on the tractor,
re-start the engine and place the throttle lever in the
Fast " " position.
IMPORTANT: Recheck the area making certain the area
is clear.
7. Move the tractor’s PTO (Blade Engage) to the ON
position. Remain in the operator’s position with the
cutting deck engaged until the deck is cleaned.
8. Move the tractor’s PTO (Blade Engage) to the OFF
position. Turn the ignition key to the STOP position to
turn the tractor’s engine off. Turn the water off.
9. Pull back the lock collar of the nozzle adapter to disconnect the adapter from the nozzle washout port.
10. Move the tractor to a dry area, preferably a concrete or
paved area. Engage the mower deck PTO to remove
excess water and to help dry before putting the tractor
away.

CLAMP
FUEL FILTER

FIG. 26

CLEANING
•

Clean engine, battery, seat, finish, etc. of all foreign
matter.
• Keep finished surfaces and wheels free of all gasoline,
oil, etc.
• Protect painted surfaces with automotive type wax.
We do not recommend using a garden hose or pressure
washer to clean your tractor unless the engine and transmission are covered to keep water out. Water in engine or
transmission will shorten the useful life of your tractor. Use
compressed air or a leaf blower to remove grass, leaves
and trash from tractor and mower.

•

DECK WASHOUT PORT (See Fig. 27)
Your tractor’s deck is equipped with a washout port on
its surface as part of its deck wash system. It should be
utilized after each use.
1. Drive the tractor to a level, clear spot on your lawn,
near enough to a water spigot for your garden hose to
reach.
IMPORTANT: Make certain the tractor’s discharge chute is
directed AWAY from your house, garage, parked cars, etc.
Remove bagger chute or mulch cover if attached.
2. Make sure the PTO (Blade Engage) is not engaged,
set the parking brake, and stop the engine.
3. Thread the nozzle adapter (packaged with your tractor’s
Operator’s Manual) onto the end of your garden hose.
4. Pull back the lock collar of the nozzle adapter and push
the adapter onto the deck washout port at the left end
of the mower deck. Release the lock collar to lock the
adapter on the nozzle.

•

WARNING: A broken or missing washout
fitting could expose you or others to
thrown objects from contact with the blade.
Replace broken or missing washout fitting immediately, prior to using mower
again.
Plug any holes in mower with bolts and
locknuts.

SERVICE AND ADJUSTMENTS
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:
• Depress brake pedal fully and set parking brake.
• Place attachment clutch in “DISENGAGED” position.
• Turn ignition key to “STOP” and remove key.
• Make sure the blades and all moving parts have completely stopped.
• Disconnect spark plug wire from spark plug and place wire where it cannot come in contact
with plug.
•

TRACTOR (See Fig. 28)
TO REMOVE MOWER
•
•
•

Place attachment clutch in “DISENGAGED” position.
Lower attachment lift lever to its lowest position.
Disengage belt tension rod (K) from lock bracket (L).

•
•

CAUTION: Belt tension rod is spring
loaded. Have a tight grip on rod and release slowly.
•
•
•

•

From right side of mower, disconnect anti-sway bar (S)
from right rear mower bracket (D) - remove retainer
spring and washer and pull mower toward you until the
bar falls from the hole in bracket.
Turn tractor steering wheel to the left as far as it will
go.
Slide mower out from under right side of tractor.

TO INSTALL MOWER
Follow procedure described in “INSTALL MOWER AND
DRIVE BELT” in the Assembly section of this manual.

Remove mower belt from electric clutch pulley (M).
Disconnect front link (E) from mower - remove retainer
spring and washer.
Go to either side of mower and disconnect mower
suspension arm (A) from chassis and rear lift link (C)
from rear mower bracket (D) - remove retainer springs
and washers.
Go to other side of mower and disconnect the suspension arm and rear lift link.

TO LEVEL MOWER
Make sure tires are properly inflated to the PSI shown on
tires. If tires are over or under inflated, it may affect the
appearance of your lawn and lead you to think the mower
is not adjusted properly.
VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 29)
• With all tires properly inflated and if your lawn appears
unevenly cut, determine which side of mower is cutting
lower.
NOTE: As desired, you can raise the low side of mower
or lower the high side.

CAUTION: After rear lift links are disconnected, the attachment lift lever will be
spring loaded. Have a tight grip on lift lever
when changing position of the lever.

B
M

K
F
A
E
H

FIG. 28

SERVICE AND ADJUSTMENTS
•
•

Go to side of mower you wish to adjust.
With a 3/4" or adjustable wrench, turn lift link adjustment nut (A) to the left to lower the mower, or, to the
right to raise the mower.

FRONT-TO-BACK ADJUSTMENT (See Figs. 31 and 32)
IMPORTANT: Deck must be level side-to-side.
To obtain the best cutting results, the mower blades should
be adjusted so the front tip is 1/8" to 1/2" lower than the
rear tip when the mower is in its highest position.
CAUTION: Blades are sharp. Protect your
hands with gloves and/or wrap blade with
heavy cloth.

•
•
•
•
•

Turn nut left
to lower mower

Turn nut right
to raise mower
02948

FIG. 29
NOTE: Each full turn of adjustment nut will change mower
height about 3/16".
• Test your adjustment by mowing some uncut grass
and visually checking the appearance. Readjust, if
necessary, until you are satisfied with the results.

Raise mower to highest position.
Position any blade so the tip is pointing straight forward.
Measure distance (B) to the ground at front and rear
tip of the blade.
If front tip of blade is not 1/8" to 1/2" lower than the rear
tip, go to the front of tractor.
With an 11/16" or adjustable wrench, loosen jam nut
A several turns to clear adjustment nut B.
With a 3/4" or adjustable wrench, turn front link adjustment nut (B) clockwise (tighten) to raise the front of
mower, or, counterclockwise (loosen) to lower the front
mower.
02548

PRECISION SIDE-TO-SIDE ADJUSTMENT
(See Fig. 30)
• With all tires properly inflated, park tractor on level
ground or driveway.

FIG. 31

CAUTION: Blades are sharp. Protect your
hands with gloves and/or wrap blade with
heavy cloth.
B

•
•

Raise mower to its highest position.
At both sides of mower, position blade at side and
measure the distance (A) from bottom edge of blade
to the ground. The distance should be the same on
both sides.
If adjustment is necessary, see steps 2 and 3 in Visual
Adjustment instructions above.
Recheck measurements, adjust if necessary until both
sides are equal.

Tighten adjust nut
B to raise mower

02966

Loosen adjust nut
B to lower mower

02950

Loosen jam nut A first

FIG. 32
FIG.30

NOTE: Each full turn of the adjustment nut will change
mower height about 1/8".
• Recheck measurements, adjust if necessary until front
tip of blade is 1/8" to 1/2" lower than the rear tip.
• Hold adjustment nut in position with wrench and tighten
jam nut securely against adjustment nut.

SERVICE AND ADJUSTMENTS
TO REPLACE MOWER BLADE DRIVE BELT
(See Fig. 33)

BELT REMOVAL • Remove mower (See “TO REMOVE MOWER” in this
section of manual).
NOTE: Observe entire motion drive belt and position of all
belt guides and keepers.
• Disconnect clutch wire harness (A).
• Remove anti-rotation link (B) on right side of tractor.
• Remove belt from stationary idler (C) and clutching
idler (D).
• Remove belt from centerspan idler (E).
• Pull belt slack toward rear of tractor. Carefully remove
belt upwards from transmission input pulley and over
cooling fan blades (F).
• Remove belt downward from engine pulley and around
electric clutch (G).
• Slide belt toward rear of tractor, off the steering plate
(H) and remove from tractor.

MOWER DRIVE BELT REMOVAL
• Park tractor on a level surface. Engage parking
brake.
• Lower attachment lift lever to its lowest position.
• Disengage belt tension rod (K) from lock bracket (L).
CAUTION: Belt tension rod is spring
loaded. Have a firm grip on rod and
release slowly.
•

Remove screws (P) from mandrel covers (Q) and
remove covers.
Remove any dirt or grass clippings which may have
accumulated around mandrels and entire upper deck
surface.
Remove belt from electric clutch pulley (M), both mandrel pulleys (R) and all idler pulleys (S).

•
•

BELT INSTALLATION • Install new belt from tractor rear to front, over the steering plate (H) and above clutch brake pedal shaft (J).
• Pull belt toward front of tractor and roll belt around
electric clutch and onto engine pulley (G).
• Pull belt toward rear of tractor. Carefully work belt down
around transmission cooling fan and onto the input
pulley (F). Be sure belt is inside the belt keeper.
• Install belt on centerspan idler (E).
• Install belt through stationary idler (C) and clutching
idler (D).
• Reinstall anti-rotation link (B) on right side of tractor.
Tighten securely.
• Reconnect clutch harness (A).
• Make sure belt is in all pulley grooves and inside all
belt guides and keepers.
• Install mower (See “TO INSTALL MOWER” in this
section of manual).

MOWER DRIVE BELT INSTALLATION
• Install belt around all mandrel pulleys (R) and around
idler pulleys (S) as shown.
• Install belt onto electric clutch pulley (M).
IMPORTANT: Check belt for proper routing in all mower
pulley grooves.
• Reassemble mandrel covers (Q). Securely tighten all
screws.
• Engage belt tension rod (K) on locking bracket (L).
CAUTION: Belt tension rod is spring
loaded. Have a tight grip on rod and
engage slowly.
•

Raise attachment lift lever to highest position.
P
Q

G
Q

H
B
R

A
C

D
S

E
R

FIG. 33

TO REPLACE MOTION DRIVE BELT
(See Fig. 34)
Park the tractor on level surface. Engage parking brake.
For assistance, there is a belt installation guide decal on
bottom side of left footrest.

02953
electric

FIG. 34

SERVICE AND ADJUSTMENTS
TO CHECK BRAKE

TO START ENGINE WITH A WEAK BATTERY
(See Fig. 36)

If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be serviced.
You may also check brake by:
• Park tractor on a level, dry concrete or paved surface,
depress brake pedal all the way down and engage
parking brake.
• Disengage transmission by placing freewheel control
in “transmission disengaged” position. Pull freewheel
control out and into the slot and release so it is held
in the disengaged position.
The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, then
the brake needs to be serviced. Contact a qualified service
center.

WARNING: Lead-acid batteries generate explosive gases. Keep sparks,
flame and smoking materials away from
batteries. Always wear eye protection
when around batteries.
If your battery is too weak to start the engine, it should be
recharged. (See "BATTERY" in the MAINTENANCE section of this manual).
If “jumper cables” are used for emergency starting, follow
this procedure:
IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12
VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12
VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO
START OTHER VEHICLES.

FRONT WHEEL TOE-IN/CAMBER

TO ATTACH JUMPER CABLES • Connect one end of the RED cable to the POSITIVE
(+) terminal of each battery(A-B), taking care not to
short against tractor chassis.
• Connect one end of the BLACK cable to the NEGATIVE
(-) terminal (C) of fully charged battery.
• Connect the other end of the BLACK cable (D) to good
chassis ground, away from fuel tank and battery.

Your new tractor front wheel toe-in and camber is set at the
factory and is normal. The front wheel toe-in and camber
are not adjustable. If damage has occurred to affect the
factory set front wheel toe-in or camber, contact a qualified
service center.

TO REMOVE WHEEL FOR REPAIRS
(See Fig. 35)

TO REMOVE CABLES, REVERSE ORDER • BLACK cable first from chassis and then from the fully
charged battery.
• RED cable last from both batteries.

•
•

Block up axle securely.
Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key
- Do not lose).
• Repair tire and reassemble.
• On rear wheels only: align grooves in rear wheel hub
and axle. Insert square key.
• Replace washers and snap retaining ring securely in
axle groove.
• Replace axle cover.
NOTE: To seal tire punctures and prevent flat tires due
to slow leaks, tire sealant may be purchased from your
local parts dealer. Tire sealant also prevents tire dry rot
and corrosion.

WEAK OR DEAD
BATTERY

FULLY CHARGED
BATTERY

FIG. 36

REPLACING BATTERY (See Fig. 37)

WASHERS

WARNING: Do not short battery terminals by allowing
a wrench or any other object to contact both terminals at
the same time. Before connecting battery, remove metal
bracelets, wristwatch bands, rings, etc.
Positive terminal must be connected first to prevent sparking from accidental grounding.
• Lift hood to raised position.
• Disconnect BLACK battery cable (A) then RED battery
cable and carefully remove battery from tractor.

RETAINING
RING
AXLE COVER

SQUARE KEY (REAR
WHEEL ONLY)

FIG. 35

SERVICE AND ADJUSTMENTS
•
•
•

•

Install new battery with terminals in same position as
old battery.
First connect RED battery cable (B) to positive (+) battery
terminal with hex bolt and keps nut as shown. Tighten
securely. Slide terminal cover (C) over terminal.
Connect BLACK grounding cable to negative (-) battery
terminal with remaining hex bolt and keps nut. Tighten
securely

TO REMOVE HOOD AND GRILL ASSEMBLY
(See Fig. 38)
•
•
•
•

Raise hood.
Unsnap headlight wire connector.
Stand in front of tractor. Grasp hood at sides, tilt toward
engine and lift off of tractor.
To replace, reverse above procedure.

Close hood.
HOOD
A Negative
(Black)
Cable
C
HEADLIGHT
WIRE
CONNECTOR
Positive B
(Red)
Cable
02778

02954

FIG. 37

TO REPLACE HEADLIGHT BULB
•
•
•
•

FIG. 38

Raise hood.
Pull bulb holder out of the hole in the backside of the
grill.
Replace bulb in holder and push bulb holder securely
back into the hole in the backside of the grill.
Close hood.

ENGINE
TO ADJUST THROTTLE CONTROL CABLE
The throttle control has been preset at the factory and
adjustment should not be necessary. If adjustment is necessary, see engine manual.

INTERLOCKS AND RELAYS
Loose or damaged wiring may cause your tractor to run
poorly, stop running, or prevent it from starting.
• Check wiring. See electrical wiring diagram in the
Repair Parts section.

TO ADJUST CHOKE CONTROL
The choke control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engne manual.

TO REPLACE FUSE
Replace with 20 amp automotive-type plug-in fuse. The
fuse holder is located behind the dash.

TO ADJUST CARBURETOR
Your carburetor is not adjustable. If your engine does not
operate properly due to suspected carburetor problems,
take your tractor to an authorized service center for repair
and/or adjustment.

STORAGE
Immediately prepare your tractor for storage at the end
of the season or if the tractor will not be used for 30 days
or more.

ENGINE
FUEL SYSTEM
IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS
FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING
ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH
LEADS TO SEPARATION AND FORMATION OF ACIDS DURING
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM
OF AN ENGINE WHILE IN STORAGE.

WARNING: Never store the tractor with
gasoline in the tank inside a building
where fumes may reach an open flame
or spark. Allow the engine to cool before
storing in any enclosure.

TRACTOR

•

Empty the fuel tank by starting the engine and let it run
until the fuel lines and carburetor are empty.
• Never use engine or carburetor cleaner products in
the fuel tank or permanent damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.

Remove mower from tractor for winter storage. When
mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a
clean, dry area.
• Clean entire tractor (See “CLEANING” in the Maintenance section of this manual).
• Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments
section of this manual).
• Lubricate as shown in the Maintenance section of this
manual.
• Be sure that all nuts, bolts and screws are securely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
• Touch up all rusted or chipped paint surfaces; sand
lightly before painting.

ENGINE OIL
Drain oil (with engine warm) and replace with clean engine
oil. (See “ENGINE” in the Maintenance section of this
manual).

BATTERY

CYLINDER(S)

•
•

•

•
•

Fully charge the battery for storage.
After a period of time in storage, battery may require
recharging.
To help prevent corrosion and power leakage during
long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see “TO
CLEAN BATTERY AND TERMINALS” in the Maintenance section of this manual).
After cleaning, leave cables disconnected and place
cables where they cannot come in contact with battery
terminals.
If battery is removed from tractor for storage, do not
store battery directly on concrete or damp surfaces.

•
•

Remove spark plug(s).
Pour one ounce of oil through spark plug hole(s) into
cylinder(s).
Turn ignition key to “START” position for a few seconds
to distribute oil.
Replace with new spark plug(s).

OTHER
•
•
•
•

Do not store gasoline from one season to another.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
If possible, store your tractor indoors and cover it to
give protection from dust and dirt.
Cover your tractor with a suitable protective cover that
does not retain moisture. Do not use plastic. Plastic
cannot breathe which allows condensation to form and
will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE
AND EXHAUST AREAS ARE STILL WARM.

TROUBLESHOOTING POINTS
PROBLEM

CAUSE

CORRECTION

Will not start

1.
2.
3.
4.
5.
6.
7.
8.

Hard to start

Out of fuel.
Engine not “CHOKED” properly.
Engine flooded.
Bad spark plug.
Weak or dead battery.
Dirty air filter.
Dirty fuel filter.
Water in fuel.

9.
10.

Loose or damaged wiring.
Carburetor out of adjustment.

9.
10.

11.

Engine valves out of adjustment.

11.

Fill fuel tank.
See “TO START ENGINE” in Operation section.
Wait several minutes before attempting to start.
Replace spark plug.
Recharge or replace battery.
Clean/replace air filter.
Replace fuel filter.
Empty fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.

1.
2.
3.
4.
5.
6.
7.

Dirty air filter.
Bad spark plug.
Weak or dead battery.
Dirty fuel filter.
Stale or dirty fuel.
Loose or damaged wiring.
Carburetor out of adjustment.

1.
2.
3.
4.
5.
6.
7.

Engine valves out of adjustment.

Clean/replace air filter.
Replace spark plug.
Recharge or replace battery.
Replace fuel filter.
Empty fuel tank and refill tank with fresh, clean gasoline.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.

Engine will not turn over

1.
2.
3.
4.
5.
6.
7.
8.
9.

Brake pedal not depressed.
Attachment clutch is engaged.
Weak or dead battery.
Blown fuse.
Corroded battery terminals.
Loose or damaged wiring.
Faulty ignition switch.
Faulty solenoid or starter.
Faulty operator presence switch(es).

1.
2.
3.
4.
5.
6.
7.
8.
9.

Depress brake pedal.
Disengage attachment clutch.
Recharge or replace battery.
Replace fuse.
Clean battery terminals.
Check all wiring.
Check/replace ignition switch.
Check/replace solenoid or starter.
Contact an authorized service center/department.

Engine clicks but will not
start

1.
2.
3.
4.

Weak or dead battery.
Corroded battery terminals.
Loose or damaged wiring.
Faulty solenoid or starter.

1.
2.
3.
4.

Recharge or replace battery.
Clean battery terminals.
Check all wiring.
Check/replace solenoid or starter.

Loss of power

1.
2.
3.
4.
5.
6.
7.
8.
9.

Cutting too much grass/too fast.
Throttle in “CHOKE” position.
Build-up of grass, leaves and trash under mower.
Dirty air filter.
Low oil level/dirty oil.
Faulty spark plug.
Dirty fuel filter.
Stale or dirty fuel.
Water in fuel.

1.
2.
3.
4.
5.
6.
7.
8.
9.

Raise cutting height/reduce speed.
Adjust throttle control.
Clean underside of mower housing.
Clean/replace air filter.
Check oil level/change oil.
Clean and regap or change spark plug.
Replace fuel filter.
Empty fuel tank and refill tank with fresh, clean gasoline.
Empty fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
Connect and tighten spark plug wire.
Clean engine air screen/fins.
Clean/replace muffler.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.

Excessive vibration

10.
11.
12.
13.
14.

Spark plug wire loose.
Dirty engine air screen/fins.
Dirty/clogged muffler.
Loose or damaged wiring.
Carburetor out of adjustment.

10.
11.
12.
13.
14.

15.

Engine valves out of adjustment.

15.

1.
2.
3.

Worn, bent or loose blade.
Bent blade mandrel.
Loose/damaged part(s).

1.
2.
3.

Replace blade. Tighten blade bolt.
Replace blade mandrel.
Tighten loose part(s). Replace damaged parts.

TROUBLESHOOTING POINTS
PROBLEM

CAUSE

CORRECTION

Engine dies when
tractor is shifted
into reverse

Turn ignition key to
ROS "ON" position.
See Operation section.

Reverse operation system
(ROS) is not "ON" while
mower or other attachment
is engaged.

Engine continues to run
when operator leaves seat
with attachment clutch
engaged

Faulty operator-safety presence control system.

Check wiring, switches and connections. If not
corrected, contact an authorized service center/
department.

Poor cut - uneven

1.
2.
3.
4.
5.

Worn, bent or loose blade.
Mower deck not level.
Buildup of grass, leaves, and trash under mower.
Bent blade mandrel.
Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels.

1.
2.
3.
4.
5.

Replace blade. Tighten blade bolt.
Level mower deck.
Clean underside of mower housing.
Replace blade mandrel.
Clean around mandrels to open vent holes.

Mower blades will not
rotate

1.
2.
3.
4.

Obstruction in clutch mechanism.
Worn/damaged mower drive belt.
Frozen idler pulley.
Frozen blade mandrel.

1.
2.
3.
4.

Remove obstruction.
Replace mower drive belt.
Replace idler pulley.
Replace blade mandrel.

Poor grass discharge

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

Engine speed too slow.
Travel speed too fast.
Wet grass.
Mower deck not level.
Low/uneven tire air pressure.
Worn, bent or loose blade.
Buildup of grass, leaves and trash under mower.
Mower drive belt worn.
Blades improperly installed.
Improper blades used.
Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels.

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

Place throttle control in “FAST” position.
Shift to slower speed.
Allow grass to dry before mowing.
Level mower deck.
Check tires for proper air pressure.
Replace blade. Tighten blade bolt.
Clean underside of mower housing.
Replace mower drive belt.
Reinstall blades sharp edge down.
Replace with blades listed in this manual.
Clean around mandrels to open vent holes.

Headlight(s) not working
(if so equipped)

1.
2.
3.
4.
5.

Light switch is “OFF”.
Bulb(s) or lamp(s) burned out.
Faulty light switch.
Loose or damaged wiring.
Blown fuse.

1.
2.
3.
4.
5.

Turn light switch “ON”.
Replace bulb(s) or lamp(s).
Check/replace light switch.
Check wiring and connections.
Replace fuse.

Battery will not charge

1.
2.
3.
4.

Bad battery cell(s).
Poor cable connections.
Faulty regulator (if so equipped).
Faulty alternator.

1.
2.
3.
4.

Replace battery.
Check/clean all connections.
Replace regulator.
Replace alternator.

Loss of drive

1.
2.
3.

Freewheel control in “disengaged” position.
Motion drive belt worn, damaged, or broken.
Air trapped in transmission during shipment
or servicing.

1.
2.
3.

Place freewheel control in “engaged” position.
Replace motion drive belt.
Purge transmission.

Engine “backfires” when
turning engine “OFF”

Engine throttle control not set between half and
full speed (fast) position before stopping engine.

Move throttle control between half and full speed
(fast) position before stopping engine.

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
SCHEMATIC
SCH12

BATTERY

SOLENOID

STARTER

RED

A
RED

FUSE

AMMETER
(OPTIONAL)

BLACK

ELECTRIC CLUTCH
WHITE

WHITE

RED

BLACK

WHITE

BLACK

PTO SWITCH
(DISENGAGED)

GRAY

A2
RED

CLUTCH/BRAKE
(PEDAL UP)

BLACK

REVERSE SWITCH
(NOT IN REVERSE)

BLACK
BLACK

BLACK

BLACK
BLACK

BLACK

1
6

SEAT SWITCH
(NOT OCCUPIED)

GRAY

BLACK /WHITE

JUNCTION
CONNECTOR

C F H

SPARK
PLUGS GAP
(2 PLUGS ON
TWIN CYL. ENGINES)

IGNITION
UNIT

B E G

(OPTIONAL)
HOUR
METER

BLUE

BLACK

A D
PTO SWITCH

SHORTING
CONNECTOR

CHASSIS
HARNESS

FUEL
LINE

(MATING SIDE)

BLACK

BLUE

POWER OUTLET
(OPTIONAL)

BLUE

CHARGING SYSTEM OUTPUT
9 - 1 6 AMP DC @ 3600 RPM

FUEL SHUT-OFF
SOLENOID
(IF EQUIPPED)

NOTES

BLACK

12V

REGULATOR

ORANGE

RED

STATOR

28 VOLTS AC @ 3600 RPM (REGULATOR DISCONNECTED)
BROWN

BLACK

LIGHT
SWITCH
HEADLIGHTS

2
1

IGNITION SWITCH
POSITION

CIRCUIT

OFF
RUN/OVERRIDE

M+G+A1
B+A1

RUN
START

B+A1
B + S + A1

“MAKE”

L+A2

CHASSIS HARNESS
CONNECTOR
(MATING SIDE)

DASH HARNESS
CONNECTOR

WIRING INSULATED CLIPS
NOTE: IF WIRING INSULATED
CLIPS WERE REMOVED FOR
SERVICING OF UNIT, THEY
SHOULD BE RE-INSTALLED TO
PROPERLY SECURE YOUR
WIRING.

NON-REMOVABLE
CONNECTIONS

REMOVABLE
CONNECTIONS

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
ELECTRICAL
T07S
33

30
21

2
1

91
99
100

27
43
41
40

25
55

101

With 12V Outlet Option

103
71
59
94

29
With Service Minder Option

92
46

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
ELECTRICAL

KEY
NO.
1
2
8
16
21
22
24
25
26
27
28
29
30
33
34
40
41
42
43
46
50
55
59
71
79
90
91
92
93
94
99
100
101
103

PART
NO.
532 16 34-65
874 76 04-12
532 18 64-91
532 17 61-38
532 18 37-59
532 41 52-J
532 40 02-53
532 41 28-95
532 17 51-58
873 51 04-00
532 14 54-91
532 40 15-45
532 19 33-50
532 41 19-35
532 11 07-12
532 40 11-04
817 72 04-08
532 13 15-63
532 19 25-07
532 40 17-63
532 17 46-51
817 06 05-12
532 40 03-03
532 19 42-76
532 17 52-42
532 40 07-24
532 19 02-70
532 19 66-15
532 19 25-40
532 19 18-34
817 67 04-12
819 09 14-16
532 19 83-17
532 40 79-62

DESCRIPTION
Battery
Bolt Hex Head 1/4-20 x 3/4
Box Battery
Switch Interlock Push-In
Harness Socket Light w/4152J
Bulb, Light
Cable Battery
Cable Start Red 17.5"
Fuse
Nut Keps Hex 1/4-20 unc
Cable, Ground
Switch, Seat
Switch Ignition
Key/Chain
Switch Light/Reset
Harness Ign Dash
Screw Thd Cut 1/4-20 x 1/2
Cover Terminal
Solenoid
Gauge Hourmeter
Switch, PTO
Screw Thdrol 5/16-18 x 3/4 TYTT
Outlet 12-Volt
Harness Ignition, Chassis
Bulbholder Asm. Incandescent
Cover Terminal Battery
Strap Battery Mount Front
Harness Pigtail
Screw
Module Reverse
Screw Hexwsh Thdrol 1/4-20 x 3/4
Washer 9/32 x 7/8 x 16 Ga.
Pigtail MATNLK
Harness Pigtail 12V Outlet

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
CHASSIS

15
208

204

210
212
214
203

207

130

211

206

209

234
181
176

130

202

234

176

205

176
177

175

150

178

196
221

195
161

176

176
37

162
199

182

194

181

68
194

130
235

236
130

213
218

180

213
165

162

68
183

189

68
217

228
181

194

152
228

189

189
189

chassis-tex_tex gt husq_14

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
CHASSIS

KEY
NO.

PART
NO.

5
14
15
18
25
34
36
37
52
58
68
130
150
152
161
162
165
175
176
177
178
180
181
182
183
189
194

532 40 87-01
532 41 10-46
532 19 89-07
532 40 86-07
532 19 89-06
532 19 61-25
817 06 05-12
532 40 18-25
873 68 05-00
532 19 43-14
817 49 05-08
532 41 63-58
532 19 85-12
532 19 95-35
532 40 18-26
532 14 24-32
532 19 68-26
532 19 63-04
532 40 07-76
532 19 52-27
532 19 97-82
532 19 54-77
532 40 30-25
532 40 68-59
874 78 05-20
817 00 05-12
873 90 05-00

DESCRIPTION
Dash
Hood
Lens LH
Grille
Lens RH
Plate Engine
Screw 5/16-18 x 3/4
Fender
Nut Crown Lock 5/16-18
Bracket Fender
Screw 5/16-18 x 1/2
Screw #10 x 0.750 BOS Thread
Duct Heat Hood
Shield Browning/Debris
Console Fuel Window
Screw Hex Wsh Hi-Lo 1/4 x 1/2
Bracket Support Tank
Crossmember
Screw 10-24 x 5/8 Wshd Qdrx
Bushing Steering
Cargo Asm. Net
Chassis
Bushing Mtg. Fender Crgo.
Dash Lower
Bolt Fin Hex 5/16-18 unc x 1-1/4
Screw 5/16-18 x 3/4
Nut Lock Hex Flange 5/16-18

KEY
NO.

PART
NO.

195
196
199
202
203
204
205
206
207
208
209
210
211
212
213
214
217
218
221
228
234
235
236

532 40 35-71
532 41 77-78
532 19 82-59
532 40 30-48
532 40 30-76
532 41 66-15
532 40 17-09
532 40 17-11
532 19 71-98
532 19 71-99
532 19 91-30
532 19 91-31
532 19 91-32
532 19 91-33
874 76 05-12
532 19 91-45
532 40 91-67
532 19 63-95
532 19 89-09
532 19 51-61
532 40 47-42
532 40 61-29
873 93 05-00

DESCRIPTION
Plug Cruise/Phone
Console Asm. Deck Lift
Plate Deck Lift
Vent Side Hood RH
Vent Side Hood LH
Vent Asm Hood Top
Skirt Hood Side RH
Skirt Hood Side LH
Bezel RH
Bezel LH
Insert Hex Top RH
Insert Hex Top LH
Insert Hex Bottom RH
Insert Hex Bottom LH
Bolt Hex Hd 5/16-18 unc x 3/4
Clip Retainer
Rod Pivot
X-Piece Hood Stop
Reflector LH
Stud Fastener
Bumper Hood
Spacer Fender
Nut Center Lock 5/16-18 unc

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
DRIVE

220

74
216

143

221

171

184

197

196

125
42
125

80
64

125

167
159

125

170
52

160

51
226

188
159

211

185
186

189
166

161

187

279

174
233

190

176

153

276

175
51
125

52
9

178
225

51
7

183

166

116
2

33
205
230

116
2
1
73

183

9
7
205

99
73

33
230

drive-tex_K66_fender_1

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
DRIVE

KEY
NO.

PART
NO.

1
2
7
9
15
17
22
23
29
33
35
42
49
50
51
52
56
64
69
70
73
74
80
99
116
125
143
153
159
160
161
166

532 41 41-45
532 00 70-70
532 19 98-37
532 14 00-80
819 13 13-16
532 40 10-72
532 19 73-29
532 14 08-45
532 40 72-45
812 00 00-53
532 19 95-91
532 12 48-72
872 11 06-14
532 19 43-27
873 90 06-00
532 19 43-26
532 12 59-07
532 19 62-00
532 12 38-00
532 40 02-98
874 49 05-44
532 14 24-32
532 40 71-82
532 41 57-44
873 90 05-00
817 00 05-12
817 49 05-08
532 12 47-88
876 02 04-12
532 16 94-84
532 10 57-09
532 19 72-90

DESCRIPTION
Transaxle, TuffTorq K66
Key
Hub Asm. Wheel
Bolt Hub Wheel
Washer 13/32 x 13/16 x 16 Ga.
Spring, Brake
Rod Shift
Knob Deluxe 1/2-13 unc
Rod, Brake
Ring E
Rod, Brake, Park
Cover, Foot Pedal
Bolt
Pulley Idler Flat
Lock Nut 3/8-16
Idler V-Groove 910" Offset
V-Belt, Drive
Shaft Asm. Pedal Brake Control
Washer 11/32 x 1-5/8 x 16 Ga.
Control Asm.
Bolt Hex Flghd 5/16-18 Gr. 5
Screw Hx Wsh Hi-Lo 1/4 x 1/2 unc
Strap Torque
Rod Bypass
Nut Lock Hex Flange 5/16-18
Screw 5/16-18 x 3/4
Screw Thdrol 5/16-18 x 1/2
Retainer Spring
Pin Cotter 1/8 x 3/4
Retainer Clip
Spring, Return, Clutch
Nut Push .625

KEY
NO.

PART
NO.

167
170
171
174
175
176
178
183
184
185
186
187
188
189
190
195
196
197
205
211
216
220
221
225
226
230
233
276
279

532 40 52-57
532 19 43-22
872 11 06-16
532 19 72-89
532 40 85-39
532 19 62-14
532 19 74-56
532 19 73-57
532 40 31-18
872 11 06-20
532 19 43-21
819 13 32-10
532 19 43-23
532 19 43-17
532 19 43-18
532 40 51-13
817 00 06-16
532 19 97-69
532 12 38-00
532 19 62-12
532 19 61-31
532 19 89-08
532 40 31-87
532 40 73-11
532 40 71-09
532 00 75-63
532 40 52-96
874 78 07-16
532 41 37-78

DESCRIPTION
Latch Brake Parking
Keeper Belt Centerspan
Bolt
Nut Push
Shaft Asm Shift
Arm Clevis Rod Shift
Spring Shift
Spacer Axle
Handle Parking Brake
Bolt
Spacer Retainer
Washer
Link Clutch Ground Drive
Bellcrank Ground Drive
Keeper Bellcrank Ground Drive
Bracket Rod Brake
Screw 3/8-16 x 1
Bracket Clutch Anti-Rotation
Washer 1 1/32 x 1 5/8 x 16 Ga.
Bearing Nylon
Bracket Pulley Idler
Reflector RH
Retainer Spring Clip Handle
Keeper Belt Trans.
Bracket Mount Torque
Washer Hardened
Washer Serrated
Bolt Fin Hex 7/16 - 14 x 1 Gr. 5
Link Asm. Shift

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
ENGINE

87
20

84
15

84
12
37 91

84
82

70
81

9
37

41
42

90
2

SPARK ARRESTER KIT

engine-tex_bs-2cyl_2

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
ENGINE

KEY PART
NO. NO.
1
-----2
9
11
12
15
18
20
21
22
28
29
31
37
41
42
45

532 14 97-23
532 19 43-20
532 17 93-35
532 19 43-43
532 19 34-99
532 19 42-67
532 17 83-85
532 41 63-58
532 19 15-96
532 40 11-35
532 13 71-80
532 14 50-06
532 12 34-87
532 12 61-97
810 04 07-00
873 51 04-00

KEY
NO.
62
69
70
71
79
81
82
84
85
86
87
90
91

DESCRIPTION
Engine B&S Model No. 44Q7771039-B1
Muffler
Keeper Belt Engine
Clutch Electric
Pulley Engine
Tank Fuel 4.0
Cap Asm
Control Throttle
Screw #10 x 0.750 BOS Thread
Control Choke
Fuel Line
Spark Arrester Kit
Clip Push-In Hinged
Clamp Hose
Washer 1-1/2 OD x 15/32 ID x .250
Washer Lock 7/16
Nut Keps Hex 1/4-20 unc

PART
NO.
DESCRIPTION
532 14 66-29
Shield Heat Muffler
532 16 53-91
Gasket
532 15 99-55
Tube Exhaust LH
532 16 05-89
Tube Exhaust RH
532 18 39-06
Screw Socket Head
532 14 84-56
Tube Drain Oil Easy
532 18 16-54
Plug Drain Oil
817 06 06-20
Screw 3/8-16 x 1-1/4
532 17 99-53
Bolt Hex 7/16-20 x 3.75 Gr. 5
532 18 43-62
Nut Hex M8-1.25
532 19 82-39
Bolt 5/16-18 unc x 1 w/Sems
817 00 06-16
Screw 3/8-16 x 1
532 18 74-95
Bushing 1.375 OD

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
For engine service and replacement parts, call the toll free
number for your engine manufacturer listed below:
Briggs & Stratton
1-800-233-3723

Engine Power Rating Information
The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive
Engineers) code J11940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-5). Actual gross engine power will be lower and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both
the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power
equipment (actual “on-site” or net horsepower). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine.

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
STEERING ASSEMBLY

HUSQ SR

PREM 2

26
45

26
1

63
19

60
57

61
8

67
2

98
7

6
4

35
58

28
13

15
22

69
68

5
62

13
14
15

53 8

70
steering-tex_Special_3

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
STEERING ASSEMBLY

KEY
NO.
1
2
4
5
6
7
8
9
13
14
15
16
19
21
22
26
28
35
45
51
53
57
58
59
60
61
62
63
64
66
67
68
69
70

PART
NO.

DESCRIPTION

532 41 46-56X418
532 19 59-68
532 40 30-89
532 40 30-90
532 00 62-66H
532 12 17-48
812 00 00-29
532 12 12-32
532 12 17-49
810 04 06-00
873 54 06-00
532 40 82-19
532 19 47-29
532 18 67-37
532 19 48-45
532 41 59-87
817 00 06-12
532 19 47-32
819 18 38-12
873 94 08-00
532 18 89-67
532 19 72-46
532 19 47-47
532 19 47-48
873 97 10-00
532 19 47-40
532 19 47-41
817 00 05-12
532 19 98-49
871 02 07-48
532 19 47-37
873 90 07-00
532 19 91-62
532 19 61-97

Wheel, Steering
Axle Asm., Front
Spindle Asm. LH
Spindle Asm. RH
Bearing, Race Thrust Harden
Washer 25/32 x 1-5/8 x 16 Ga.
Ring, Clip #T5304-75
Cap, Spindle
Washer 25/32 x 1-1/4 x 16 Ga.
Washer, Lock Hvy Hlcl Spr 3/8
Nut, Crown Lock 3/8-24 unf
Shaft Steering
Plate Steering
Adapter, Wheel Steering
Bushing, Strg. Blk
Insert, Wheel Steering
Screw 3/8-16 x 3/4
Gear, Sector Plate
Washer 9/16 x 2-3/8 x 12 Ga.
Nut Hex Jam Toplock 1/2-20 unf
Washer Hardened .793 x 1.637 x .060
Bracket Upstop
Bolt Shoulder Sector Pivot CFM
Washer Thrust Sector Steering
Nut Flange Lock 5/8-11
Draglink LH
Draglink, RH
Screw 5/16-18 x 3/4
Retainer Clip Spring Steering
Bolt Hex Fghd 7/16-14 x 3 Serr
Bushing PM Front Axle
Nut Lock Flange 7/16-14 Gr. 5
Washer 1.5 x .505 x .118
Bracket Deck Susp. Front

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
SEAT ASSEMBLY

8
8
7
7

8
41

37
37

44
2

3
seat-tex_6.5SL_2

KEY
NO.
1
2
3
5
6
7
8
10
21

PART
NO.
532 40 66-21
532 18 01-66
532 14 06-75
532 14 50-06
873 80 06-00
532 12 41-81X
532 17 18-77
532 19 69-77
532 17 18-52

KEY
NO.

DESCRIPTION

37
40
41
43
44

Seat
Bracket Pivot Fender
Strap, Asm Fender
Clip, Push In, Hinged
Nut, Lock w/Ins. 3/8-16 unc
Spring, Seat Cprsn
Bolt 5/16-18 uncx 3/4 w/Sems
Pan, Seat
Bolt, Shoulder 5/16-18

PART
NO.
873 80 05-00
532 19 76-61
532 19 82-00
874 76 06-12
819 13 38-12

DESCRIPTION
Nut, Lock 5/16-18 unc
Handle Slide Seat
Spring Latch Seat
Bolt Fin Hex 3/8-16 unc x 3/4
Washer 13/32 x 2-3/8 x 12 Ga.

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
DECALS

4
3

12
8

KEY PART
NO. NO.
1
532 41 16-58
2
532 41 57-80
4
532 41 82-73
6
532 41 84-97
8
532 19 87-85
9
532 14 50-05
10 532 18 09-41
12 532 17 05-63

KEY PART
NO. NO.
14 532 41 82-16
- - 532 16 69-60
- - 532 40 17-71
- - 532 40 17-70
- - 532 41 82-77
- - 532 41 82-76
- - 532 41 82-78

DESCRIPTION
Decal, Operator's
Decal, Hood Emblem
Decal, replacement
Decal, Engine HP
Decal, Mower Sch.
Decal, Battery Dnge/Poi
Decal, Hood Cust. Resp.
Decal, Mower warning Keep Hand
Away

KEY
PART
NO.
NO.
DESCRIPTION
1
532 05 91-92 Cap, Valve, Tire
2
532 06 51-39 Stem, Valve
3
532 14 45-09 Rim Assembly, Front
4
532 00 81-34 Tube, Front (Service Item Only)
5
532 10 62-30X Tire, Front
6
532 12 49-57 Fitting, Grease (Front Wheel Only)
7
532 12 49-59 Bearing, Flange (Front Wheel Only)
8
532 17 50-39 Cap, Axle (Front Wheel Only)
9
532 10 55-88X Tire, Rear
10 532 00 71-54 Tube, Rear (Service Item Only)
11 532 16 41-27 Rim Assembly, Rear
- - 532 14 43-34 Sealant, Tire (10 oz. Tube)
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

WHEELS AND TIRES
1
2

11 3
4
7

10
5

DESCRIPTION
Decal, Panel SD
Decal, Bypass
Pad, Footrest, LH
Pad, Footrest, RH
Decal, Deck Air Induct
Manual, Owner's (Eng)
Manual, Owner's (Fr)

9
8

wheel_art_1-vgt

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
MOWER DECK

47
185

39
34
192
49

21
122

52
7

114

43
196

52
32

241
242

1
30

116
117

120
29

113
194

12
16

26
24

19
27

21
21

60
59

190

189

190
11

187

184
8

187
mower_deck 54-tex_10

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
MOWER DECK

KEY
NO.
1
6
7
8
11
-12
13
14
15
16
17
19
21
24
25
26
27
29
30
31
32
33
34
39
43
46
47
49
50

PART
NO.
532 41 87-08
532 19 60-66
532 19 71-81
532 17 43-65
532 18 72-56
532 18 72-55
532 40 03-37
532 18 72-91
532 18 72-81
532 11 04-85X
819 13 13-12
872 14 05-05
532 19 42-08
873 68 05-00
532 10 53-04X
532 17 81-02
532 11 04-52X
532 18 89-38
532 13 14-91
532 17 39-84
532 18 76-90
532 15 35-35
532 40 02-34
873 68 06-00
532 19 73-80
532 19 60-65
532 13 77-29
532 19 61-03
873 90 06-00
872 11 06-16

KEY
NO.

DESCRIPTION
Deck Weldment Mower
Cover Mandrel LH
Cover Mandrel RH
Bolt 7/16 Asm. Blade
Blade Bagging
Blade Mulching
Bar Anti-Sway
Shaft Asm. w/Lower Bearing
Housing, Mandrel
Bearing, Ball, Mandrel
Washer 13/32 x 13/16 x 12 Ga.
Bolt Carr. 5/16-18 x 5/8
Pin Cotter 5/16 Bow tie Lock
Nut, Crownlock 5/16-18 unc
Cap Sleeve
Spring, Torsion
Nut, Push
Deflector Shield
Rod, Hinge
Screw, Thdroll Washer Head
Washer, Spacer Mower Vented
Pulley, Mandrel
Nut, Flg. Top Lock
Nut Crownlock 3/8-16 unc
Pulley, Idler, Stationary
Arm, Idler
Screw, Thdroll. 1/4-20 x 5/8
V-Belt, Mower
Nut, Lock Flg. 3/8-16 unc
Bolt Rdhd Sqnk 3/8-16 unc x 2

PART
NO.

52
58
59
60
97
98
113
114
116
117
120
122
185
187
188
189
190
192
194
195
241
242
--

532 19 73-79
532 18 73-42
532 18 73-44
532 18 76-07
532 17 85-15
532 19 61-05
872 11 05-08
532 18 75-56
532 19 34-06
532 17 48-73
819 13 20-12
532 18 75-57
873 90 07-00
532 19 51-61
873 90 05-00
532 19 51-85
532 19 65-39
532 19 84-68
872 14 07-16
872 14 06-20
532 15 29-27
532 41 55-98
532 18 72-92

532 41 82-29

DESCRIPTION
Pulley Idler 4.50
Baffle Right
Baffle Left
Baffle Center
Washer Hardened
Spring Drive
Bolt Rdhd Sqnk 5/16-18 x 3/4
Rod Tension Relief
Bolt, Shoulder
Gauge Wheel
Washer 13/32 x 1-1/4 x 12 Ga.
Bushing Tension Relief
Nut Lock Flange 7/16-14 Gr. 5
Stud Fastener w/"D" Anti-Rotation
Nut Lock Hex Flange 5/16-18
Arm Susp. Mower Rear
Bolt Shoulder
Keeper Belt Idler
Bolt Carr Sqnk 3/8-16 x 2-1/4
Bolt Rdhd 3/8-16 unc x 2-3/4 Gr. 5
Screw
Washout Port
Mandrel Assembly (Includes housing, shaft assembly, and bearing
only - pulley/nut/washer and blade
bolt/washers not included)
Replacement Mower, Complete

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR - MODEL NO. 2754GLS (96043004700), PRODUCT NO. 960 43 00-47
MOWER LIFT

7
87
87

89
3
10

88
97
2

91
87

lift-tex_3

89
87

KEY
NO.
2
3
7
10
87
88
89

PART
NO.

KEY
NO.

DESCRIPTION

532 19 52-23
532 19 52-30
532 41 15-55X42
532 19 63-14
532 19 42-09
532 19 53-04
819 19 19-12

Shaft Asm., Lift
Lever Asm., Lift RH
Grip, Lever
Spring Torsion
Pin Cotter 7/16 Bow Tie Lock
Spring Lift Assist
Washer Clear Zinc

90
91
97
98

PART
NO.
532 19 42-08
532 40 34-07
817 00 06-12
532 19 52-64

DESCRIPTION
Pin Cotter 5/16 Bow Tie Lock
Link Lift Susp Mower Rear
Screw 3/8-16 x .75
Link Lift Susp. Front Mower

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION

FOL
DA
L
O
NG D
THIS
O
I
T
S
T
A
E
D LIN
1
5
DEG
E
RE
E
S
LOP
E

ONLY RIDE UP AND DOWN HILL,
NOT ACROSS HILL

15 DEGREES MAX.

WARNING: To avoid serious injury, operate your tractor up and
down the face of slopes, never across the face. Do not mow
slopes greater than 15 degrees. Make turns gradually to prevent
tipping or loss of control. Exercise extreme caution when
changing direction on slopes.
1. Fold this page along dotted line indicated above.
2. Hold page before you so that its left edge is vertically parallel to a tree
trunk or other upright structure.
3. Sight across the fold in the direction of hill slope you want to measure.
4. Compare the angle of the fold with the slope of the hill.

SERVICE NOTES

532 41 82-76 12.06.07 SR

WARRANTY STATEMENT
SECTION 1: LIMITED WARRANTY
Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from
defects in material and workmanship from the date of purchase for the “Warranty Period” of the product as set forth below:
Lifetime Warranty (Parts and Labor): All tiller tines and trimmer shafts against breakage. Proof of purchase required.
Lifetime Warranty (“PARTS ONLY” after initial warranty expiration): Ignition coils and modules on handheld product.
Proof of purchase required.
WARRANTY SCHEDULE FOR TURF CARE Equipment - Zero Turn Riders
(New warranty applies to units sold after August 1, 2005. Also applies to units factory-equipped with R.O.P.S.
EZ Zero Turn Riders: 3 year consumer warranty or 600 hours of use (when used solely at the owner’s residence.)
EZ Zero Turn Riders: 1 year commercial warranty or 600 hours of use.
iZ, LZ & BZ Zero Turn Riders: 5 year consumer warranty or 1,500 hours of use (when used solely at the owner’s residence.)
iZ, LZ & BZ Zero Turn Riders: 5 year commercial warranty or 1,500 hours of use.
3 Year or 1,500 Hour Commercial Use Warranty: spindles on zero turn riders, hydraulic pumps and wheel motors.
Warranty Schedule for Turf Care Walk Behind Units - W, WG & WH Zero Turn Riders - 3 year consumer and commercial
warranty. New warranty applies to units sold after August 1, 2005. Also applies to units factory-equipped with R.O.P.S.
2 Year COMMERCIAL and CONSUMER Warranty: all Husqvarna ground-engaging commercial equipment.
WARRANTY SCHEDULE FOR CONSUMER TURF CARE EQUIPMENT:
2 Year Consumer Warranty: Automatic mower, all Residential Zero Turn Riders, all lawn, yard and garden tractors, all
noncommercial walk behind mowers, tillers, chain saws, trimmers, brushcutters, clearing saws, snow blowers, handheld
blowers, backpack blowers, hedge trimmers, electrical products and power-assist collection systems for noncommercial,
nonprofessional, noninstitutional or nonincome producing use, except as herein stated. All consumer product use must have
been limited to the owner’s residence.
WARRANTY SCHEDULE FOR CONSUMER FOREST & GARDEN EQUIPMENT:
2 Year Consumer Warranty: all consumer chain saws, trimmers, brushcutters, clearing saws, handheld blowers, backpack
blowers, hedge trimmers, and electrical products for noncommercial, nonprofessional, noninstitutional or nonincome
producing use, except as herein stated. All consumer product use must have been limited to the owner’s residence.
2 Year or 2,000 Hour Powertrain & 1 Year or 1,000 Hour Body Warranty: Husqvarna Utility Vehicles.
1 Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for non-commercial, non-professional,
noninstitutional, non-municipality or non-income producing use. All 300 series trimmers, brushcutters, clearing saws,
hovering trimmers, stick edgers, backpack blowers, hand held blowers, hedge trimmers, power-assist collection systems for
commercial, institutional, professional or income producing purposes or use.
1 Year Conditional Component Warranty: Chain saw crankshafts for commercial/professional use (parts and labor).Saw
must be operated with Husqvarna XP 2 cycle oil.
90 Day Commercial Warranty: Automatic mower, chain saws, 100 series trimmers, power cutters, stump grinders, pole
saws, pole pruners, snow throwers, model series 580 & 600 walk-behind mowers, or any Husqvarna product used for
commercial, institutional, professional, municipality or income producing purposes or use except as otherwise provided herein.
Batteries: 1 year prorated limited warranty with 100% replacement during the first 6 months.
Rental Warranty: 90 days on all applicable professional equipment reference warranty time period charts
located in the back of the Retailer Warranty Policy & Procedure Manual.
Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer’s original purchase for defects in
material and workmanship. Normal wear, tear or abuse is not covered under warranty. Product must be returned to Charlotte
with a warranty claim form. All care and maintenance instructions must be followed as stated by the manufacturer on the
care label. The fit of the protective apparel/boot is not covered under warranty.
30 Day Warranty: Replacement parts, accessories including bars and chains, tools and display items. Emission control
system components necessary to comply with CARB-TIER II and EPA regulations, except for those components which are
part of engine systems manufactured by third part engine manufacturers for which the purchaser has received a separate
warranty with product at time of purchase.

SECTION 2: HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY
Printed in U.S.A.

Husqvarna will repair or replace defective components without charge for parts or labor if a component fails because of a
defect in material or workmanship during the warranty period.

SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY
The following items are not covered by this warranty:
(1) Normal customer maintenance items which become worn through normal regular use, including, but not limited to, belts,
blades, blade adapters, bulbs, clutches, clutch drums, filters, guide bars, lubricants, rewind springs, saw chain, spark plugs,

starter ropes and tines;
(2) Natural discoloration of material due to ultraviolet light;
(3) Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective manufacturer’s
warranty as provided in writing with the product information supplied at the time of purchase; all claims must be sent to the
appropriate manufacturer;
(4) Lawn and garden attachments are covered by a third party which gives a warranty, all claims for warranty should be sent
to the manufacturer,
(5) Commercial or consumer mowing decks with sand abrasion damage.
(6) Emission Control System components necessary to comply with CARB-TIER II and EPA regulations which are
manufactured by third party engine manufacturer.

SECTION 4: EXCEPTIONS AND LIMITATIONS
This warranty shall be inapplicable to defects resulting from the following:
(1) Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any
adverse reaction due to incorrect storage or use habits;
(2) Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished
by Husqvarna;
(3) Alterations or modifications that change the intended use of the product or affects the product’s performance, operation,
safety, or durability, or causes the product to fail to comply with any applicable laws; or:
(4) Additional damage to parts or components due to continued use occurring after any of the above.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE
PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR
BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT TO THE EXTENT
PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO THE WARRANTY PERIOD AS
DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RESERVES THE RIGHT TO CHANGE OR
IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NOTICE, AND DOES NOT ASSUME OBLIGATION TO UPDATE
PREVIOUSLY MANUFACTURED PRODUCTS.
Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.

SECTION 5: CUSTOMER RESPONSIBILITIES
The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written in the
maintenance section of the Owner’s/Operator’s manual. Should an operational problem or failure occur, the product should
not be used, but delivered as is to an authorized Husqvarna retailer for evaluation. Proof of purchase, as explained in
section 6, rests solely with the customer.

SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION
It is the Owner’s and Retailer’s responsibility to make certain that the Warranty Registration Card is properly filled out and
mailed to Husqvarna Forest & Garden Company. This card should be mailed within ten (10) days from the date of purchase
in order to confirm the warranty and to facilitate post-sale service.
Proof of purchase must be presented to the authorized Husqvarna retailer in order to obtain warranty service. This proof
must include date purchased, model number, serial number, and complete name and address of the selling retailer.
To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna
retailer in a timely manner, no later than thirty (30) days from date of the operational problem or failure. The product must be
delivered at the owner’s expense. Downtime, pick-up and delivery charges are not covered by this warranty. An authorized
Husqvarna retailer can be normally located through the “Yellow Pages” of the local telephone directory or by calling 1-800HUSKY62 for a retailer in your area.

HUSQVARNA
7349 Statesville Road
Charlotte, NC 28269

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Page Mode                       : UseOutlines
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Create Date                     : 2008:01:21 14:04:05Z
Modify Date                     : 2008:01:28 13:41:36+01:00
Metadata Date                   : 2008:01:28 13:41:36+01:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Creator                         : Husqvarna
Title                           : OM, 2754 GLS, 96043004700, 2008-01, Ride Mower
Document ID                     : uuid:da54a35b-12b0-4f9e-b24f-46f415f8fd83
Instance ID                     : uuid:32870f98-67be-4dc5-8204-40b15a9beb67
Page Count                      : 48
Page Layout                     : OneColumn
Author                          : Husqvarna

EXIF Metadata provided by EXIF.tools

Husqvarna 2754 Gls Users Manual OM, GLS, 96043004700, 2008 01, Ride Mower

2754 GLS HUSO2008_USen_O0802014_

2754 GLS to the manual 61789a60-3451-7854-f5d0-ffc0ba9d1eae

Navigation menu

Versions of this User Manual:

Views

Navigation